Lasse Collin [Wed, 21 Sep 2011 14:30:50 +0000 (17:30 +0300)]
XZ: Fix incorrect XZ_BUF_ERROR
xz_dec_run() could incorrectly return XZ_BUF_ERROR if all of the
following was true:
- The caller knows how many bytes of output to expect and only provides
that much output space.
- When the last output bytes are decoded, the caller-provided input
buffer ends right before the LZMA2 end of payload marker. So LZMA2
won't provide more output anymore, but it won't know it yet and thus
won't return XZ_STREAM_END yet.
- A BCJ filter is in use and it hasn't left any unfiltered bytes in the
temp buffer. This can happen with any BCJ filter, but in practice
it's more likely with filters other than the x86 BCJ.
This fixes <https://bugzilla.redhat.com/show_bug.cgi?id=735408> where
Squashfs thinks that a valid file system is corrupt.
This also fixes a similar bug in single-call mode where the uncompressed
size of a block using BCJ + LZMA2 was 0 bytes and caller provided no
output space. Many empty .xz files don't contain any blocks and thus
don't trigger this bug.
This also tweaks a closely related detail: xz_dec_bcj_run() could call
xz_dec_lzma2_run() to decode into temp buffer when it was known to be
useless. This was harmless although it wasted a minuscule number of CPU
cycles.
* git://github.com/davem330/net: (27 commits)
xfrm: Perform a replay check after return from async codepaths
fib:fix BUG_ON in fib_nl_newrule when add new fib rule
ixgbe: fix possible null buffer error
tg3: fix VLAN tagging regression
net: pxa168: Fix build errors by including interrupt.h
netconsole: switch init_netconsole() to late_initcall
gianfar: Fix overflow check and return value for gfar_get_cls_all()
ppp_generic: fix multilink fragment MTU calculation (again)
GRETH: avoid overwrite IP-stack's IP-frags checksum
GRETH: RX/TX bytes were never increased
ipv6: fix a possible double free
b43: Fix beacon problem in ad-hoc mode
Bluetooth: add support for 2011 mac mini
Bluetooth: Add MacBookAir4,1 support
Bluetooth: Fixed BT ST Channel reg order
r8169: do not enable the TBI for anything but the original 8169.
r8169: remove erroneous processing of always set bit.
r8169: fix WOL setting for 8105 and 8111evl
r8169: add MODULE_FIRMWARE for the firmware of 8111evl
r8169: fix the reset setting for 8111evl
...
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
* 'for-linus' of git://git.kernel.dk/linux-block:
floppy: use del_timer_sync() in init cleanup
blk-cgroup: be able to remove the record of unplugged device
block: Don't check QUEUE_FLAG_SAME_COMP in __blk_complete_request
mm: Add comment explaining task state setting in bdi_forker_thread()
mm: Cleanup clearing of BDI_pending bit in bdi_forker_thread()
block: simplify force plug flush code a little bit
block: change force plug flush call order
block: Fix queue_flag update when rq_affinity goes from 2 to 1
block: separate priority boosting from REQ_META
block: remove READ_META and WRITE_META
xen-blkback: fixed indentation and comments
xen-blkback: Don't disconnect backend until state switched to XenbusStateClosed.
init: carefully handle loglevel option on kernel cmdline.
When a malformed loglevel value (for example "${abc}") is passed on the
kernel cmdline, the loglevel itself is being set to 0.
That then suppresses all following messages, including all the errors
and crashes caused by other malformed cmdline options. This could make
debugging process quite tricky.
This patch leaves the previous value of loglevel if the new value is
incorrect and reports an error code in this case.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@sysgo.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Hansen [Tue, 20 Sep 2011 22:19:41 +0000 (15:19 -0700)]
teach /proc/$pid/numa_maps about transparent hugepages
This is modeled after the smaps code.
It detects transparent hugepages and then does a single gather_stats()
for the page as a whole. This has two benifits:
1. It is more efficient since it does many pages in a single shot.
2. It does not have to break down the huge page.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Hansen [Tue, 20 Sep 2011 22:19:39 +0000 (15:19 -0700)]
break out numa_maps gather_pte_stats() checks
gather_pte_stats() does a number of checks on a target page
to see whether it should even be considered for statistics.
This breaks that code out in to a separate function so that
we can use it in the transparent hugepage case in the next
patch.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com> Acked-by: Hugh Dickins <hughd@google.com> Reviewed-by: Christoph Lameter <cl@gentwo.org> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Hansen [Tue, 20 Sep 2011 22:19:38 +0000 (15:19 -0700)]
make /proc/$pid/numa_maps gather_stats() take variable page size
We need to teach the numa_maps code about transparent huge pages. The
first step is to teach gather_stats() that the pte it is dealing with
might represent more than one page.
Note that will we use this in a moment for transparent huge pages since
they have use a single pmd_t which _acts_ as a "surrogate" for a bunch
of smaller pte_t's.
I'm a _bit_ unhappy that this interface counts in hugetlbfs page sizes
for hugetlbfs pages and PAGE_SIZE for normal pages. That means that to
figure out how many _bytes_ "dirty=1" means, you must first know the
hugetlbfs page size. That's easier said than done especially if you
don't have visibility in to the mount.
But, that's probably a discussion for another day especially since it
would change behavior to fix it. But, just in case anyone wonders why
this patch only passes a '1' in the hugetlb case...
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Incorrect variable was used in validating the akm_suites array from
NL80211_ATTR_AKM_SUITES. In addition, there was no explicit
validation of the array length (we only have room for
NL80211_MAX_NR_AKM_SUITES).
This can result in a buffer write overflow for stack variables with
arbitrary data from user space. The nl80211 commands using the affected
functionality require GENL_ADMIN_PERM, so this is only exposed to admin
users.
Cc: stable@kernel.org Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the dawn of its time, iwlwifi has used
interruptible waits to wait for synchronous
commands and firmware loading.
This leads to "interesting" bugs, because it
can't actually handle the interruptions; for
example when a command sending is interrupted
it will assume the command completed fully,
and then leave it pending, which leads to all
kinds of trouble when the command finishes
later.
Since there's no easy way to gracefully deal
with interruptions, fix the driver to not use
interruptible waits.
This at least fixes the error
iwlagn 0000:02:00.0: Error: Response NULL in 'REPLY_SCAN_ABORT_CMD'
I have seen in P2P testing, but it is likely
that there are other errors caused by this.
Cc: stable@kernel.org # 2.6.39+ Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the command queue is constantly busy,
which can happen in P2P, the hangcheck
timer will frequently find a command in
it and will eventually reset the device
because nothing sets the timestamp for
this queue when commands are processed.
Fix this by setting the timestamp when
a command completes.
iwlegacy does not support P2P, but this patch fix possible
unneeded hardware resets, hence is needed.
Cc: stable@kernel.org # 2.6.39+ Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
During the endurance testing, rx frames are not getting DMAd from
MAC whereas pcu rx frame counters are getting updated properly.
As per systems team input updated the initval to fix rx dma stuck
issue.
Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
xfrm: Perform a replay check after return from async codepaths
When asyncronous crypto algorithms are used, there might be many
packets that passed the xfrm replay check, but the replay advance
function is not called yet for these packets. So the replay check
function would accept a replay of all of these packets. Also the
system might crash if there are more packets in async processing
than the size of the anti replay window, because the replay advance
function would try to update the replay window beyond the bounds.
This pach adds a second replay check after resuming from the async
processing to fix these issues.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
fib:fix BUG_ON in fib_nl_newrule when add new fib rule
add new fib rule can cause BUG_ON happen
the reproduce shell is
ip rule add pref 38
ip rule add pref 38
ip rule add to 192.168.3.0/24 goto 38
ip rule del pref 38
ip rule add to 192.168.3.0/24 goto 38
ip rule add pref 38
then the BUG_ON will happen
del BUG_ON and use (ctarget == NULL) identify whether this rule is unresolved
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Daney [Tue, 30 Aug 2011 13:45:20 +0000 (06:45 -0700)]
MIPS: Don't clobber CP0_STATUS value for CONFIG_MIPS_MT_SMTC
Reported-by: Edgar E. Iglesias <edgar.iglesias@gmail.com> Signed-off-by: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/2753/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Sat, 20 Aug 2011 15:44:00 +0000 (08:44 -0700)]
MIPS: Octeon: Select CONFIG_HOLES_IN_ZONE
Current Octeon systems do in fact have holes in their memory zones.
We need to select HOLES_IN_ZONE. If we do not, some memory
configurations will result in crashes at boot time like this:
Yong Zhang [Tue, 16 Aug 2011 01:54:54 +0000 (09:54 +0800)]
MIPS: Compat: Use 32-bit wrapper for compat_sys_futex.
We can't trust userspace to pass signed-extend arguments. Not correctly
sign-extended arguments to futex-wait result in architecturally undefined
operation of 32-bit arithmetic instructions.
For example, if 'val' is too big and bit-31 is 1, the caller may enter
endless loop at:
futex_wait_setup()
{
...
if (uval != val) {
queue_unlock(q, *hb);
ret = -EWOULDBLOCK;
...
}
Signed-off-by: Yong Zhang <yong.zhang@windriver.com>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2714/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
kbuild: introduce ccflags-y, asflags-y and ldflags-y
Moreover, these flags (at least EXTRA_CFLAGS) have been documented for command
line use. By default, gmake(1) do not override command line setting, so this is
likely to result in build failure or unexpected behavior.
Replace their usage by Kbuild's `{as,cc,ld}flags-y'.
To: linux-kernel@vger.kernel.org Cc: Sam Ravnborg <sam@ravnborg.org>
Patchwork: https://patchwork.linux-mips.org/patch/2710/ Cc: linux-mips@linux-mips.org Signed-off-by: Arnaud Lacombe <lacombar@gmail.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Fri, 12 Aug 2011 06:28:35 +0000 (08:28 +0200)]
MIPS: Alchemy: DB1200: Disable cascade IRQ in handler
Disable the cascade IRQ in the cascade handler. This is required to
get the DB1300 working, and also gets rid of all spurious interrupts
previously observed on the DB1200; so Config[OD] can be disabled
again for better performance.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2708/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
John Crispin [Mon, 18 Jul 2011 16:08:40 +0000 (18:08 +0200)]
MIPS: Lantiq: Fix external interrupt sources
The irq base offset needs to be ignored when matching irqs to external
interrupt pins. Taking the offset into account resulted in the EIU not
being brought up properly.
Ralf Baechle [Tue, 2 Aug 2011 21:52:48 +0000 (22:52 +0100)]
MIPS: tlbex: Fix build error in R3000 code.
Only some GCC versions such as gcc 4.2 notice that the variable wr in
build_r3000_tlb_modify_handler is used uninitialized. When using one
of those GCCs the build will fail due to -Werror. GCC 4.6 does not
warn about the uninitialized use of wr.
CC arch/mips/pmc-sierra/msp71xx/msp_irq.o
/home/ralf/src/linux/linux-mips/arch/mips/pmc-sierra/msp71xx/msp_irq.c:112:2: error: request for member ‘flags’ in something not a structure or union
/home/ralf/src/linux/linux-mips/arch/mips/pmc-sierra/msp71xx/msp_irq.c:118:2: error: request for member ‘flags’ in something not a structure or union
make[4]: *** [arch/mips/pmc-sierra/msp71xx/msp_irq.o] Error 1
do_signal() does __put_user() which can fault, resulting in a might_sleep()
warning in down_read(&mm->mmap_sem) and a "scheduling while atomic" warning
when mmap_sem is contented. On Swarm this also results in:
WARNING: at kernel/smp.c:459 smp_call_function_many+0x148/0x398()
Modules linked in:
Call Trace:
Fixed by enabling interrupts in do_notify_resume before delivering signals.
[ralf@linux-mips.org: Reported and original fix by tglx but I wanted to
minimize the amount of code being run with interrupts disabled so I moved
the local_irq_disable() call right into do_notify_resume. Which is saner
than doing it in entry.S.]
Reported-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS: Loongson: Mark cascade interrupts IRQF_NO_THREAD
There are two cascade interrupts in Loongson machines, one for bonito
northbridge, another for the 8259A controller in the southbridge. Both
want to be non threaded.
MIPS: Mark cascade and low level interrupts IRQF_NO_THREAD
Mark interrupts with no_action handler, cascade interrupts, low level
interrupts (bus error, halt ..) with IRQF_NO_THREAD to exclude them
from forced threading.
Thomas Gleixner [Sat, 23 Jul 2011 12:41:23 +0000 (12:41 +0000)]
MIPS: Ftrace: Fix the CONFIG_DYNAMIC_FTRACE=n compile
arch/mips/kernel/ftrace.c: In function ‘ftrace_get_parent_ra_addr’:
arch/mips/kernel/ftrace.c:212: error: implicit declaration of function ‘in_kernel_space’
arch/mips/kernel/ftrace.c: In function ‘prepare_ftrace_return’:
arch/mips/kernel/ftrace.c:314: error: ‘MCOUNT_OFFSET_INSNS’ undeclared (first use in this function)
arch/mips/kernel/ftrace.c:314: error: (Each undeclared identifier is reported only once
arch/mips/kernel/ftrace.c:314: error: for each function it appears in.)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2634/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/pci/pci-rc32434.c: In function 'rc32434_pci_init':
arch/mips/pci/pci-rc32434.c:217:16: error: 'rcrc32434_res_pci_io1' undeclared (first use in this function)
arch/mips/pci/pci-rc32434.c:217:16: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [arch/mips/pci/pci-rc32434.o] Error 1
Nicolas Pitre [Wed, 3 Aug 2011 14:50:38 +0000 (15:50 +0100)]
ARM: mach-nuc93x: delete
This architecture received only generic maintenance since December 2009
when it was originally submitted, and no actual additional support since
then. It has no defconfig entry either, meaning that it was never built
by the ARM KAutobuild. Incidentally it currently doesn't build either
when CONFIG_MACH_NUC932EVB is selected which is the only possible config
choice.
This is therefore dead code and should be removed. If someone wants to
revive this code, it could be retrieved from the Git repository, and
ideally be merged in mach-w90x900/ instead.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Wan ZongShun <mcuos.com@gmail.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It seems that at least one PPC machine would occasionally give a (valid) 0 as
the return value from dma_map, this caused the ixgbe code to not work
correctly. A fix is pending in the PPC tree to not return 0 from dma map, but
we can also fix the driver to make sure we don't mess up in other arches as
well.
This patch is applicable to all current stable kernels.
Reported-by: Neil Horman <nhorman@redhat.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> CC: Alexander Duyck <alexander.h.duyck@intel.com> CC: stable@kernel.org Tested-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
broke VLAN tagging on outbound packets.
It ifdef'ed BCM_KERNEL_SUPPORTS_8021Q, but this
is not set anywhere. So vlan never gets set, and
all packets are sent with vlan=0.
v2: We can just remove the test. vlan_tx_tag_present
is valid regardless of whether the 802.1q module
is built.
Tested on BCM5721 rev 11.
Signed-off-by: Kasper Pedersen <kernel@kasperkp.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
Kukjin Kim [Tue, 30 Aug 2011 11:47:32 +0000 (20:47 +0900)]
ARM: SAMSUNG: Update the name of regarding Samsung GPIO
According to gpio-samsung.c, this patch updates the name of
regarding Samsung GPIO. Basically the samsung_xxx prefix is
used in gpio-samsung.c instead of s3c_xxx, because unified
name can reduce its complexity.
Note: some s3c_xxx stil remains because it is used widely.
It will be updated next time.
Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Kukjin Kim [Tue, 30 Aug 2011 11:39:08 +0000 (20:39 +0900)]
gpio/samsung: gpio-samsung.c to support Samsung GPIOs
This patch adds support for Samsung GPIOs with one gpio driver
and removes old GPIO drivers which are drivers/gpio-s3c24xx.c,
gpio-s3c64xx.c, gpio-s5p64x0.c, gpio-s5pc100.c, gpio-s5pv210.c,
gpio-exynos4.c, gpio-plat-samsung.c, plat-samsung/gpio-config.c
and gpio.c to support each Samsung SoCs before. Because the
gpio-samsung.c can replace old Samsung GPIO drivers.
Basically, the gpio-samsung.c has been made by their merging
and removing duplicated definitions.
Note: gpio-samsung.c includes some SoC dependent codes and it
will be replaced next time.
Cc: Ben Dooks <ben-linux@fluff.org> Acked-by: Grant Likely <grant.likely@secretlab.ca>
[kgene.kim@samsung.com: squash the removing and adding patches]
[kgene.kim@samsung.com: fixes bug during to register of gpio_chips] Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds platform devices and regulators for TV devices on
Samsung Goni board.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ARM: EXYNOS4: enable TV support on Universal_C210 board
This patch adds platform devices and regulators for TV devices on
Samsung Universal C210 board.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds all the resources for TV drivers and devices for Samsung
Exynos4 and S5PV210 platforms.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[m.szyprowski: squashed Exynos4 and S5PV210 patches and rewrote commit message] Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Russell King [Tue, 20 Sep 2011 22:35:15 +0000 (23:35 +0100)]
ARM: fix vmlinux.lds.S discarding sections
We are seeing linker errors caused by sections being discarded, despite
the linker script trying to keep them. The result is (eg):
`.exit.text' referenced in section `.alt.smp.init' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o
`.exit.text' referenced in section `.alt.smp.init' of net/built-in.o: defined in discarded section `.exit.text' of net/built-in.o
This is the relevent part of the linker script (reformatted to make it
clearer):
| SECTIONS
| {
| /*
| * unwind exit sections must be discarded before the rest of the
| * unwind sections get included.
| */
| /DISCARD/ : {
| *(.ARM.exidx.exit.text)
| *(.ARM.extab.exit.text)
| }
| ...
| .exit.text : {
| *(.exit.text)
| *(.memexit.text)
| }
| ...
| /DISCARD/ : {
| *(.exit.text)
| *(.memexit.text)
| *(.exit.data)
| *(.memexit.data)
| *(.memexit.rodata)
| *(.exitcall.exit)
| *(.discard)
| *(.discard.*)
| }
| }
Now, this is what the linker manual says about discarded output sections:
| The special output section name `/DISCARD/' may be used to discard
| input sections. Any input sections which are assigned to an output
| section named `/DISCARD/' are not included in the output file.
No questions, no exceptions. It doesn't say "unless they are listed
before the /DISCARD/ section." Now, this is what asn-generic/vmlinux.lds.S
says:
| /*
| * Default discarded sections.
| *
| * Some archs want to discard exit text/data at runtime rather than
| * link time due to cross-section references such as alt instructions,
| * bug table, eh_frame, etc. DISCARDS must be the last of output
| * section definitions so that such archs put those in earlier section
| * definitions.
| */
And guess what - the list _always_ includes .exit.text etc.
Now, what's actually happening is that the linker is reading the script,
and it finds the first /DISCARD/ output section at the beginning of the
script. It continues reading the script, and finds the 'DISCARD' macro
at the end, which having been postprocessed results in another
/DISCARD/ output section. As the linker already contains the earlier
/DISCARD/ output section, it adds it to that existing section, so it
effectively is placed at the start. This can be seen by using the -M
option to ld:
As you can see, all the discarded sections are grouped together - and
as a result of it being the first output section, they all appear before
any other section.
The result is that not only is the unwind information discarded (as
intended), but also the .exit.text, despite us wanting to have the
.exit.text preserved.
We can't move the unwind information elsewhere, because it'll then be
included even when we do actually discard the .exit.text (and similar)
sections.
So, work around this by avoiding the generic DISCARDS macro, and instead
conditionalize the sections to be discarded ourselves. This avoids the
ambiguity in how the linker assigns input sections to output sections,
making our script less dependent on undocumented linker behaviour.
Reported-by: Rob Herring <robherring2@gmail.com> Tested-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 1 Sep 2011 10:57:59 +0000 (11:57 +0100)]
ARM: pm: add L2 cache cleaning for suspend
We need to ensure that state is pushed out from the L2 cache when
suspending so that the resume paths can access their data before the
MMU and caches have been re-initialized. Add the necessary calls to
__cpu_suspend_save().
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Tested-by: Shawn Guo <shawn.guo@linaro.org> Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 1 Sep 2011 10:52:33 +0000 (11:52 +0100)]
ARM: pm: convert some assembly to C
Convert some of the sleep.S guts to C code, which makes it easier to
use our macros and to add L2 cache handling. We provide a helper
function, __cpu_suspend_save(), which deals with saving the common
state, setting up for resume, and flushing caches.
The remainder left as assembly code is the saving of the CPU general
purpose registers, and allocating space on the stack to save the CPU
specific registers and resume state.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Tested-by: Shawn Guo <shawn.guo@linaro.org> Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Wed, 31 Aug 2011 22:26:18 +0000 (23:26 +0100)]
ARM: pm: get rid of cpu_resume_turn_mmu_on
We don't require cpu_resume_turn_mmu_on as we can combine the ldr
instruction with the following code provided we ensure that
cpu_resume_mmu is aligned for older CPUs. Note that we also align
to a 32-byte boundary to ensure that the code can't cross a section
boundary.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Tested-by: Shawn Guo <shawn.guo@linaro.org> Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 28 Aug 2011 09:30:34 +0000 (10:30 +0100)]
ARM: pm: no need to save/restore context ID register
There is no need to save and restore the context ID register on ARMv6
and ARMv7 with a temporary page table as we write the context ID
register when we switch back to the real page tables for the thread.
Moreover, the temporary page tables do not contain any non-global
mappings, so the context ID value should not be used. To be safe,
initialize the register to a reserved context ID value.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Tested-by: Shawn Guo <shawn.guo@linaro.org> Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 27 Aug 2011 21:39:09 +0000 (22:39 +0100)]
ARM: pm: only use preallocated page table during resume
Only use the preallocated page table during the resume, not while
suspending. This avoids the overhead of having to switch unnecessarily
to the resume page table in the suspend path.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Tested-by: Shawn Guo <shawn.guo@linaro.org> Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 26 Aug 2011 19:28:52 +0000 (20:28 +0100)]
ARM: pm: preallocate a page table for suspend/resume
Preallocate a page table and setup an identity mapping for the MMU
enable code. This means we don't have to "borrow" a page table to
do this, avoiding complexities with L2 cache coherency.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Tested-by: Shawn Guo <shawn.guo@linaro.org> Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge branch 'fixes' of git://git.linaro.org/people/arnd/arm-soc
* 'fixes' of git://git.linaro.org/people/arnd/arm-soc:
mach-integrator: fix VGA base regression
arm/dt: Tegra: Update SDHCI nodes to match bindings
ARM: EXYNOS4: fix incorrect pad configuration for keypad row lines
ARM: SAMSUNG: fix to prevent declaring duplicated
ARM: SAMSUNG: fix watchdog reset issue with clk_get()
ARM: S3C64XX: Remove un-used code backlight code on SMDK6410
ARM: EXYNOS4: restart clocksource while system resumes
ARM: EXYNOS4: Fix routing timer interrupt to offline CPU
ARM: EXYNOS4: Fix return type of local_timer_setup()
ARM: EXYNOS4: Fix wrong pll type for vpll
ARM: Dove: fix second SPI initialization call
projects / karo-tx-linux.git / log