The common PM clock management functions may be used for system
suspend/resume as well as for runtime PM, so rename them
accordingly. Modify kerneldoc comments describing these functions
and kernel messages printed by them, so that they refer to power
management in general rather that to runtime PM.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Reviewed-by: Kevin Hilman <khilman@ti.com>
PM: Allow the clocks management code to be used during system suspend
The common clocks management code in drivers/base/power/clock_ops.c
is going to be used during system-wide power transitions as well as
for runtime PM, so it shouldn't depend on CONFIG_PM_RUNTIME.
However, the suspend/resume functions provided by it for
CONFIG_PM_RUNTIME unset, to be used during system-wide power
transitions, should not behave in the same way as their counterparts
defined for CONFIG_PM_RUNTIME set, because in that case the clocks
are managed differently at run time.
The names of the functions still contain the word "runtime" after
this change, but that is going to be modified by a separate patch
later.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Reviewed-by: Kevin Hilman <khilman@ti.com>
PM / Domains: Wakeup devices support for system sleep transitions
There is the problem how to handle devices set up to wake up the
system from sleep states during system-wide power transitions.
In some cases, those devices can be turned off entirely, because the
wakeup signals will be generated on their behalf anyway. In some
other cases, they will generate wakeup signals if their clocks are
stopped, but only if power is not removed from them. Finally, in
some cases, they can only generate wakeup signals if power is not
removed from them and their clocks are enabled.
To allow platform-specific code to decide whether or not to put
wakeup devices (and their PM domains) into low-power state during
system-wide transitions, such as system suspend, introduce a new
generic PM domain callback, .active_wakeup(), that will be used
during the "noirq" phase of system suspend and hibernation (after
image creation) to decide what to do with wakeup devices.
Specifically, if this callback is present and returns "true", the
generic PM domain code will not execute .stop_device() for the
given wakeup device and its PM domain won't be powered off.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Kevin Hilman <khilman@ti.com>
PM / Domains: System-wide transitions support for generic domains (v5)
Make generic PM domains support system-wide power transitions
(system suspend and hibernation). Add suspend, resume, freeze, thaw,
poweroff and restore callbacks to be associated with struct
generic_pm_domain objects and make pm_genpd_init() use them as
appropriate.
The new callbacks do nothing for devices belonging to power domains
that were powered down at run time (before the transition). For the
other devices the action carried out depends on the type of the
transition. During system suspend the power domain .suspend()
callback executes pm_generic_suspend() for the device, while the
PM domain .suspend_noirq() callback runs pm_generic_suspend_noirq()
for it, stops it and eventually removes power from the PM domain it
belongs to (after all devices in the domain have been stopped and its
subdomains have been powered off).
During system resume the PM domain .resume_noirq() callback
restores power to the PM domain (when executed for it first time),
starts the device and executes pm_generic_resume_noirq() for it,
while the .resume() callback executes pm_generic_resume() for the
device. Finally, the .complete() callback executes pm_runtime_idle()
for the device which should put it back into the suspended state if
its runtime PM usage count is equal to zero at that time.
The actions carried out during hibernation and resume from it are
analogous to the ones described above.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Reviewed-by: Kevin Hilman <khilman@ti.com>
PM / Domains: Move code from under #ifdef CONFIG_PM_RUNTIME (v2)
There is some code in drivers/base/power/domain.c that will be useful
for both runtime PM and system-wide power transitions, so make it
depend on CONFIG_PM instead of CONFIG_PM_RUNTIME.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Reviewed-by: Kevin Hilman <khilman@ti.com>
PM / Domains: Support for generic I/O PM domains (v8)
Introduce common headers, helper functions and callbacks allowing
platforms to use simple generic power domains for runtime power
management.
Introduce struct generic_pm_domain to be used for representing
power domains that each contain a number of devices and may be
parent domains or subdomains with respect to other power domains.
Among other things, this structure includes callbacks to be
provided by platforms for performing specific tasks related to
power management (i.e. ->stop_device() may disable a device's
clocks, while ->start_device() may enable them, ->power_off() is
supposed to remove power from the entire power domain
and ->power_on() is supposed to restore it).
Introduce functions that can be used as power domain runtime PM
callbacks, pm_genpd_runtime_suspend() and pm_genpd_runtime_resume(),
as well as helper functions for the initialization of a power
domain represented by a struct generic_power_domain object,
adding a device to or removing a device from it and adding or
removing subdomains.
Introduce configuration option CONFIG_PM_GENERIC_DOMAINS to be
selected by the platforms that want to use the new code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Reviewed-by: Kevin Hilman <khilman@ti.com>
PM: subsys_data in struct dev_pm_info need not depend on RM_RUNTIME
The subsys_data field of struct dev_pm_info, introduced by commit 1d2b71f61b6a10216274e27b717becf9ae101fc7 (PM / Runtime: Add subsystem
data field to struct dev_pm_info), is going to be used even if
CONFIG_PM_RUNTIME is not set, so move it from under the #ifdef.
PM / Domains: Rename struct dev_power_domain to struct dev_pm_domain
The naming convention used by commit 7538e3db6e015e890825fbd9f86599b
(PM: Add support for device power domains), which introduced the
struct dev_power_domain type for representing device power domains,
evidently confuses some developers who tend to think that objects
of this type must correspond to "power domains" as defined by
hardware, which is not the case. Namely, at the kernel level, a
struct dev_power_domain object can represent arbitrary set of devices
that are mutually dependent power management-wise and need not belong
to one hardware power domain. To avoid that confusion, rename struct
dev_power_domain to struct dev_pm_domain and rename the related
pointers in struct device and struct pm_clk_notifier_block from
pwr_domain to pm_domain.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Kevin Hilman <khilman@ti.com>
Commit e1866b33b1e89f077b7132daae3dfd9a594e9a1a (PM / Runtime: Rework
runtime PM handling during driver removal) forgot to update the
documentation in Documentation/power/runtime_pm.txt to match the new
code in drivers/base/dd.c. Update that documentation to match the
code it describes.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Reviewed-by: Kevin Hilman <khilman@ti.com>
Merge branch 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915: apply HWSTAM writes to Ivy Bridge as well
drm/i915: move IRQ function table init to i915_irq.c
drm/i915/overlay: Fix unpinning along init error paths
drm/i915: Don't call describe_obj on NULL pointers
drm/i915: Hold struct_mutex during i915_save_state/i915_restore_state
Merge branch 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pci: Use the INT_SRC_OVR IRQ (instead of GSI) to preset the ACPI SCI IRQ.
xen/mmu: Fix for linker errors when CONFIG_SMP is not defined.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (24 commits)
usbnet: Remove over-broad module alias from zaurus.
MAINTAINERS: drop Michael from bfin_mac driver
net/can: activate bit-timing calculation and netlink based drivers by default
rionet: fix NULL pointer dereference in rionet_remove
net+crypto: Use vmalloc for zlib inflate buffers.
netfilter: Fix ip_route_me_harder triggering ip_rt_bug
ipv4: Fix IPsec slowpath fragmentation problem
ipv4: Fix packet size calculation in __ip_append_data
cxgb3: skb_record_rx_queue now records the queue index relative to the net_device.
bridge: Only flood unregistered groups to routers
qlge: Add maintainer.
MAINTAINERS: mark socketcan-core lists as subscribers-only
MAINTAINERS: Remove Sven Eckelmann from BATMAN ADVANCED
r8169: fix wrong register use.
net/usb/kalmia: signedness bug in kalmia_bind()
net/usb: kalmia: Various fixes for better support of non-x86 architectures.
rtl8192cu: Fix missing firmware load
udp/recvmsg: Clear MSG_TRUNC flag when starting over for a new packet
ipv6/udp: Use the correct variable to determine non-blocking condition
netconsole: fix build when CONFIG_NETCONSOLE_DYNAMIC is turned on
...
Linus Torvalds [Thu, 30 Jun 2011 17:43:22 +0000 (10:43 -0700)]
Merge branch 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-3.x
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-3.x:
sh: use printk_ratelimited instead of printk_ratelimit
sh: Fix up unmet dependency warnings with USB EHCI/OHCI selects.
sh: fix the value of sh_dmae_slave_config in setup-sh7757
sh: fix the INTC vector for IRQ and IRL in setup-sh7757
sh: add to select the new configuration for USB EHCI/OHCI
sh: add platform_device of EHCI/OHCI to setup-sh7757
sh: fix compile error using sh7757lcr_defconfig
Linus Torvalds [Thu, 30 Jun 2011 17:43:04 +0000 (10:43 -0700)]
Merge branch 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-3.x
* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-3.x:
ARM: mach-shmobile: make a struct in board-ap4evb.c static
ARM: mach-shmobile: ag5evm: consistently name sdhi info structures
ARM: mach-shmobile: mackerel: change usbhs devices order
which means that GSI 20 (or pin 20) is to be overriden for IRQ 9.
Our code that presets the interrupt for ACPI SCI however would
use the GSI 20 instead of IRQ 9 ending up with:
as the ACPI interpreter made a call to 'acpi_gsi_to_irq' which got nine.
It used that value to request an IRQ (request_irq) and since that was not
present it failed.
The fix is to recognize that for interrupts that are overriden (in our
case we only care about the ACPI SCI) we should use the IRQ number
to present the IRQ instead of the using GSI. End result is that we get:
This alters the maintenance of the AVR32 architecture and the AT32AP machine
code to be shared between Haavard Skinnemoen and me. The status is also changed
to maintained, as we no longer are being paid to look after this architecture.
Jesse Barnes [Tue, 28 Jun 2011 20:00:41 +0000 (13:00 -0700)]
drm/i915: move IRQ function table init to i915_irq.c
This lets us make the various IRQ functions static and helps avoid
problems like the one fixed in "drm/i915: Use chipset-specific irq
installers" where one of the exported functions was called rather than
the chipset specific version.
This also fixes a UMS-mode bug -- the correct irq functions for IRL
and later chips were only getting loaded in the KMS path.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Keith Packard <keithp@keithp.com>
Chris Wilson [Tue, 28 Jun 2011 10:27:47 +0000 (11:27 +0100)]
drm/i915/overlay: Fix unpinning along init error paths
As pointed out by Dan Carpenter, it was seemingly possible to hit an error
whilst mapping the buffer for the regs (except the only likely error
returns should not happen during init) and so leak a pin count on the
bo. To handle this we would need to reacquire the struct mutex, so for
simplicity rearrange for the lock to be held for the entire function.
For extra pedagogy, test that we only call init once.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Keith Packard <keithp@keithp.com> Signed-off-by: Keith Packard <keithp@keithp.com>
Kim Phillips [Thu, 26 May 2011 03:30:34 +0000 (13:30 +1000)]
crypto: caam - fix operator precedence in shared descriptor allocation
setkey allocates 16 bytes (CAAM_CMD_SZ *
DESC_AEAD_SHARED_TEXT_LEN) shy of what is needed to
store the shared descriptor, resulting in memory
corruption. Fix this.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Ben Widawsky [Wed, 29 Jun 2011 18:41:51 +0000 (11:41 -0700)]
drm/i915: Don't call describe_obj on NULL pointers
Reported-by: Pavel Roskin <proski@gnu.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38777 Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Wed, 29 Jun 2011 07:30:34 +0000 (00:30 -0700)]
drm/i915: Hold struct_mutex during i915_save_state/i915_restore_state
Lots of register access in these functions, some of which requires the
struct mutex.
These functions now hold the struct mutex across the calls to
i915_save_display and i915_restore_display, and so the internal mutex
calls in those functions have been removed. To ensure that no-one else
was calling them (and hence violating the new required locking
invarient), those functions have been made static.
gen6_enable_rps locks the struct mutex, and so i915_restore_state
unlocks the mutex around calls to that function.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Keith Packard <keithp@keithp.com>
Linus Torvalds [Wed, 29 Jun 2011 18:07:02 +0000 (11:07 -0700)]
Merge branch 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c/pca954x: Initialize the mux to disconnected state
i2c-taos-evm: Fix log messages
Linus Torvalds [Wed, 29 Jun 2011 18:03:27 +0000 (11:03 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
arch/powerpc: use printk_ratelimited instead of printk_ratelimit
powerpc/rtas-rtc: remove sideeffects of printk_ratelimit
powerpc/pseries: remove duplicate SCSI_BNX2_ISCSI in pseries_defconfig
powerpc/e500: fix breakage with fsl_rio_mcheck_exception
powerpc/p1022ds: fix audio-related properties in the device tree
powerpc/85xx: fix NAND_CMD_READID read bytes number
Linus Torvalds [Wed, 29 Jun 2011 17:10:07 +0000 (10:10 -0700)]
ahci: change 'masking port_map' printk to KERN_WARNING level
It's not so much an error as a warning about normal Marvell crazines.
So don't use KERN_ERR that ends up spamming the console even in quiet
mode, it's not _that_ critical.
Explained by Jeff:
"Long explanation, it's a mess:
Marvell took standard AHCI, and bastardized it to include a weird mode
whereby PATA devices appear inside the AHCI DMA and interrupt
infrastructure you're familiar with.
So, PATA devices appear via pata_marvell driver, using basic legacy
IDE programming interface. But SATA devices, which might also be
attached to this chip, either work in under-performing mode or
simply don't work at all (e.g. newer 6 Gbps devices or port
multiplier attachments, NCQ, ...)
On the other hand, 'ahci' driver loads and works with the chip's
attached SATA devices quite beautifully, but is completely unable to
drive any attached PATA devices, due to the Marvell-specific
PATA-under-AHCI interface.
The "masking port_map 0x7 -> 0x3" message is the ahci driver "hiding"
the PATA port(s) from itself, making sure it will only drive the SATA
ports it knows how to drive."
Acked-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Jones [Sat, 18 Jun 2011 00:02:10 +0000 (20:02 -0400)]
usbnet: Remove over-broad module alias from zaurus.
This module and a bunch of dependancies are getting loaded on several
of laptops I have (probably picking up the mobile broadband device),
that have nothing to do with zaurus. Matching by class without
any vendor/device pair isn't the right thing to do here, as it
will prevent any other driver from correctly binding to it.
(Or in the absense of a driver, will just waste time & memory by
unnecessarily loading modules)
Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Frysinger [Mon, 27 Jun 2011 08:24:07 +0000 (08:24 +0000)]
MAINTAINERS: drop Michael from bfin_mac driver
We want people to just use the list now rather than hitting up people
who are no longer responsible for it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/can: activate bit-timing calculation and netlink based drivers by default
The two options "CAN bit-timing calculation" and
"Platform CAN drivers with Netlink support" have a "default Y". In order to
activate them by default, change to "default y".
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be> Signed-off-by: David S. Miller <davem@davemloft.net>
Yinglin Luan [Sat, 25 Jun 2011 18:12:12 +0000 (18:12 +0000)]
rionet: fix NULL pointer dereference in rionet_remove
Function rionet_remove initializes local variable 'ndev' to NULL
and do nothing changes before the call to unregister_netdev(ndev),
this could cause a NULL pointer dereference.
Reported-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: Yinglin Luan <synmyth@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 29 Jun 2011 12:48:41 +0000 (05:48 -0700)]
net+crypto: Use vmalloc for zlib inflate buffers.
They are 64K and result in order-4 allocations, even with SLUB.
Therefore, just like we always have for the deflate buffers, use
vmalloc.
Reported-by: Martin Jackson <mjackson220.list@gmail.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid creating input routes with ip_route_me_harder.
It does not work for locally generated packets. Instead,
restrict sockets to provide valid saddr for output route (or
unicast saddr for transparent proxy). For other traffic
allow saddr to be unicast or local but if callers forget
to check saddr type use 0 for the output route.
The resulting handling should be:
- REJECT TCP:
- in INPUT we can provide addr_type = RTN_LOCAL but
better allow rejecting traffic delivered with
local route (no IP address => use RTN_UNSPEC to
allow also RTN_UNICAST).
- FORWARD: RTN_UNSPEC => allow RTN_LOCAL/RTN_UNICAST
saddr, add fix to ignore RTN_BROADCAST and RTN_MULTICAST
- OUTPUT: RTN_UNSPEC
- NAT, mangle, ip_queue, nf_ip_reroute: RTN_UNSPEC in LOCAL_OUT
- IPVS:
- use RTN_LOCAL in LOCAL_OUT and FORWARD after SNAT
to restrict saddr to be local
Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
Petri Gynther [Wed, 29 Jun 2011 09:36:11 +0000 (11:36 +0200)]
i2c/pca954x: Initialize the mux to disconnected state
pca954x power-on default is channel 0 connected. If multiple pca954x
muxes are connected to the same physical I2C bus, the parent bus will
see channel 0 devices behind both muxes by default. This is bad.
1. Load I2C bus driver: creates I2C-bus-1
2. Load pca954x driver: creates virtual I2C-bus-101 and I2C-bus-111
3. Load eeprom driver
4. Try to read EEPROM @ 0x50 on I2C-bus-101. The transaction will also bleed
onto I2C-bus-111 because pca954x @ 0x71 channel 0 is connected by default.
Fix: Initialize pca954x to disconnected state in pca954x_probe()
Signed-off-by: Petri Gynther <pgynther@google.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: stable@kernel.org
powerpc/rtas-rtc: remove sideeffects of printk_ratelimit
Don't use printk_ratelimit() as an additional condition for returning
on an error. Because when the ratelimit is reached, printk_ratelimit
will return 0 and e.g. in rtas_get_boot_time won't check for an error
condition.
Signed-off-by: Christian Dietrich <christian.dietrich@informatik.uni-erlangen.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Mon, 27 Jun 2011 19:55:30 +0000 (19:55 +0000)]
powerpc/pseries: remove duplicate SCSI_BNX2_ISCSI in pseries_defconfig
Remove duplicate assignment of SCSI_BNX2_ISCSI in pseries_defconfig
introduced by: 37e0c21e powerpc/pseries: Enable iSCSI support for a number of cards
causes warning:
arch/powerpc/configs/pseries_defconfig:151:warning: override: reassigning to symbol SCSI_BNX2_ISCSI
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch updates the email address of the at32ap700x_wdt driver supported by
me to an email account I will use on a more regular basis in the future.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Linus Torvalds [Tue, 28 Jun 2011 18:15:36 +0000 (11:15 -0700)]
Merge branch 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6
* 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
Connector: Correctly set the error code in case of success when dispatching receive callbacks
Connector: Set the CN_NETLINK_USERS correctly
pti: PTI semantics fix in pti_tty_cleanup.
pti: ENXIO error case memory leak PTI fix.
pti: double-free security PTI fix
drivers:misc: ti-st: fix skipping of change remote baud
drivers/base/platform.c: don't mark platform_device_register_resndata() as __init_or_module
st_kim: Handle case of no device found for ID 0
firmware: fix GOOGLE_SMI kconfig dependency warning
Linus Torvalds [Tue, 28 Jun 2011 18:15:17 +0000 (11:15 -0700)]
Merge branch 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
MAINTAINERS: add myself as maintainer of USB/IP
usb: r8a66597-hcd: fix cannot detect low/full speed device
USB: ehci-ath79: fix a NULL pointer dereference
USB: Add new FT232H chip to drivers/usb/serial/ftdi_sio.c
usb/isp1760: Fix bug preventing the unlinking of control urbs
USB: Fix up URB error codes to reflect implementation.
xhci: Always set urb->status to zero for isoc endpoints.
xhci: Add reset on resume quirk for asrock p67 host
xHCI 1.0: Incompatible Device Error
USB: don't let errors prevent system sleep
USB: don't let the hub driver prevent system sleep
USB: change maintainership of ohci-hcd and ehci-hcd
xHCI 1.0: Force Stopped Event(FSE)
xhci: Don't warn about zeroed bMaxBurst descriptor field.
USB: Free bandwidth when usb_disable_device is called.
xhci: Reject double add of active endpoints.
USB: TI 3410/5052 USB Serial Driver: Fix mem leak when firmware is too big.
usb: musb: gadget: clear TXPKTRDY flag when set FLUSHFIFO
usb: musb: host: compare status for negative error values
Linus Torvalds [Tue, 28 Jun 2011 18:14:55 +0000 (11:14 -0700)]
Merge branch 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
serial: bcm63xx_uart: fix irq storm after rx fifo overrun.
amba pl011: platform data for reg lockup and glitch v2
amba pl011: workaround for uart registers lockup
tty: n_gsm: improper skb_pull() use was leaking framed data
tty: n_gsm: Fixed logic to decode break signal from modem status
TTY: ntty, add one more sanity check
TTY: ldisc, do not close until there are readers
8250: Fix capabilities when changing the port type
8250_pci: Fix missing const from merges
ARM: SAMSUNG: serial: Fix on handling of one clock source for UART
serial: ioremap warning fix for jsm driver.
8250_pci: add -ENODEV code for Intel EG20T PCH
Linus Torvalds [Tue, 28 Jun 2011 18:14:22 +0000 (11:14 -0700)]
Merge branch 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: comedi: fix build breakages on some platforms
Staging: brcm80211: disable drivers except for X86 or MIPS platforms
Staging: brcm80211: disable drivers for PPC platforms
Staging: iio: Make IIO depend on GENERIC_HARDIRQS
Staging: mei: fix suspend failure
Staging: fix iio builds when IIO_RING_BUFFER is not enabled
Staging: Comedi: Build only on arches providing PAGE_KERNEL_NOCACHE
Staging: fix more iio builds when IIO_RING_BUFFER is not enabled
Chris Wilson [Tue, 28 Jun 2011 10:48:51 +0000 (11:48 +0100)]
drm/i915: Use chipset-specific irq installers
Konstantin Belousov pointed out that 4697995b98417 replaced the generic
i915_driver_irq_*install() functions with chipset specific routines
accessible only through driver->irq_*install(). So update the sanity
check in i915_request_wait() to match.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Keith Packard <keithp@keithp.com>
Ben Widawsky [Fri, 24 Jun 2011 21:31:47 +0000 (14:31 -0700)]
drm/i915: forcewake fix after reset
The failure is as follows:
1. Userspace gets forcewake lock, lock count >=1
2. GPU hang/reset occurs (forcewake bit is reset)
3. count is now incorrect
The failure can only occur when using the forcewake userspace lock.
This has the unfortunate consequence of messing up the driver as well as
userspace, unless userspace closes the debugfs file, the kernel will
never end up waking the GT since the refcount will be > 1.
The solution is to try to recover the correct forcewake state based on
the refcount. There is a period of time where userspace reads/writes may
occur after the reset, before the GT has been forcewaked. The interface
was never designed to be a perfect solution for userspace reads/writes,
and the kernel portion is fixed by this patch.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Keith Packard <keithp@keithp.com>
Vasiliy Kulikov [Fri, 24 Jun 2011 12:08:38 +0000 (16:08 +0400)]
proc: restrict access to /proc/PID/io
/proc/PID/io may be used for gathering private information. E.g. for
openssh and vsftpd daemons wchars/rchars may be used to learn the
precise password length. Restrict it to processes being able to ptrace
the target process.
ptrace_may_access() is needed to prevent keeping open file descriptor of
"io" file, executing setuid binary and gathering io information of the
setuid'ed process.
Jesper Juhl [Thu, 26 May 2011 09:12:53 +0000 (11:12 +0200)]
watchdog: Intel SCU Watchdog: Fix build and remove duplicate code
Trying to build the Intel SCU Watchdog fails for me with gcc 4.6.0 -
$ gcc --version | head -n 1
gcc (GCC) 4.6.0 20110513 (prerelease)
like this :
CC drivers/watchdog/intel_scu_watchdog.o
In file included from drivers/watchdog/intel_scu_watchdog.c:49:0:
/home/jj/src/linux-2.6/arch/x86/include/asm/apb_timer.h: In function ‘apbt_time_init’:
/home/jj/src/linux-2.6/arch/x86/include/asm/apb_timer.h:65:42: warning: ‘return’ with a value, in function returning void [enabled by default]
drivers/watchdog/intel_scu_watchdog.c: In function ‘intel_scu_watchdog_init’:
drivers/watchdog/intel_scu_watchdog.c:468:2: error: implicit declaration of function ‘sfi_get_mtmr’ [-Werror=implicit-function-declaration]
drivers/watchdog/intel_scu_watchdog.c:468:32: warning: assignment makes pointer from integer without a cast [enabled by default]
cc1: some warnings being treated as errors
Florian Fainelli [Wed, 15 Jun 2011 17:15:41 +0000 (19:15 +0200)]
watchdog: mtx1-wdt: fix GPIO toggling
Commit e391be76 (MIPS: Alchemy: Clean up GPIO registers and accessors)
changed the way the GPIO was toggled. Prior to this patch, we would
always actively drive the GPIO output to either 0 or 1, this patch
drove the GPIO active to 0, and put the GPIO in tristate to drive it
to 1, unfortunately this does not work, revert back to active driving.
Using a signed variable (gstate) to hold the gpio state and using a bit-
wise operation on it also resulted in toggling value from 1 to -2 since
the variable is signed. This value was then passed on to gpio_direction_
output, which always perform a if (value) ... to set the value to the
gpio, so we were always writing a 1 to this GPIO instead of 1 -> 0 -> 1 ...
Mark Brown [Tue, 31 May 2011 13:46:55 +0000 (14:46 +0100)]
watchdog: Handle multiple wm831x watchdogs being registered
Due to the whole single instance based watchdog API we use static data
for the wm831x watchdog which means that if the system tries to register
a second one we end up trying to register the same miscdevice again,
corrupting the miscdevice list. Work around this by checking for duplicate
registrations until we get a watchdog core.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
NeilBrown [Tue, 28 Jun 2011 06:59:42 +0000 (16:59 +1000)]
md: avoid endless recovery loop when waiting for fail device to complete.
If a device fails in a way that causes pending request to take a while
to complete, md will not be able to immediately remove it from the
array in remove_and_add_spares.
It will then incorrectly look like a spare device and md will try to
recover it even though it is failed.
This leads to a recovery process starting and instantly aborting over
and over again.
We should check if the device is faulty before considering it to be a
spare. This will avoid trying to start a recovery that cannot
proceed.
This bug was introduced in 2.6.26 so that patch is suitable for any
kernel since then.
Cc: stable@kernel.org Reported-by: Jim Paradis <james.paradis@stratus.com> Signed-off-by: NeilBrown <neilb@suse.de>
Steffen Klassert [Wed, 22 Jun 2011 01:05:37 +0000 (01:05 +0000)]
ipv4: Fix IPsec slowpath fragmentation problem
ip_append_data() builds packets based on the mtu from dst_mtu(rt->dst.path).
On IPsec the effective mtu is lower because we need to add the protocol
headers and trailers later when we do the IPsec transformations. So after
the IPsec transformations the packet might be too big, which leads to a
slowpath fragmentation then. This patch fixes this by building the packets
based on the lower IPsec mtu from dst_mtu(&rt->dst) and adapts the exthdr
handling to this.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert [Wed, 22 Jun 2011 01:04:37 +0000 (01:04 +0000)]
ipv4: Fix packet size calculation in __ip_append_data
Git commit 59104f06 (ip: take care of last fragment in ip_append_data)
added a check to see if we exceed the mtu when we add trailer_len.
However, the mtu is already subtracted by the trailer length when the
xfrm transfomation bundles are set up. So IPsec packets with mtu
size get fragmented, or if the DF bit is set the packets will not
be send even though they match the mtu perfectly fine. This patch
actually reverts commit 59104f06.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hugh Dickins [Mon, 27 Jun 2011 23:18:20 +0000 (16:18 -0700)]
drm/i915: more struct_mutex locking
When auditing the locking in i915_gem.c (for a prospective change which
I then abandoned), I noticed two places where struct_mutex is not held
across GEM object manipulations that would usually require it.
Since one is in initial setup and the other in driver unload, I'm
guessing the mutex is not required for either; but post a patch in case
it is.
Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Keith Packard <keithp@keithp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Mon, 27 Jun 2011 23:18:19 +0000 (16:18 -0700)]
drm/i915: use shmem_truncate_range
The interface to ->truncate_range is changing very slightly: once "tmpfs:
take control of its truncate_range" has been applied, this can be applied.
For now there is only a slight inefficiency while this remains unapplied,
but it will soon become essential for managing shmem's use of swap.
Change i915_gem_object_truncate() to use shmem_truncate_range() directly:
which should also spare i915 later change if we switch from
inode_operations->truncate_range to file_operations->fallocate.
Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Keith Packard <keithp@keithp.com> Cc: Dave Airlie <airlied@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Mon, 27 Jun 2011 23:18:18 +0000 (16:18 -0700)]
drm/i915: use shmem_read_mapping_page
Soon tmpfs will stop supporting ->readpage and read_cache_page_gfp(): once
"tmpfs: add shmem_read_mapping_page_gfp" has been applied, this patch can
be applied to ease the transition.
Make i915_gem_object_get_pages_gtt() use shmem_read_mapping_page_gfp() in
the one place it's needed; elsewhere use shmem_read_mapping_page(), with
the mapping's gfp_mask properly initialized.
Forget about __GFP_COLD: since tmpfs initializes its pages with memset,
asking for a cold page is counter-productive.
Include linux/shmem_fs.h also in drm_gem.c: with shmem_file_setup() now
declared there too, we shall remove the prototype from linux/mm.h later.
Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Keith Packard <keithp@keithp.com> Cc: Dave Airlie <airlied@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Mon, 27 Jun 2011 23:18:17 +0000 (16:18 -0700)]
drm/ttm: use shmem_read_mapping_page
Soon tmpfs will stop supporting ->readpage and read_mapping_page(): once
"tmpfs: add shmem_read_mapping_page_gfp" has been applied, this patch can
be applied to ease the transition.
ttm_tt_swapin() and ttm_tt_swapout() use shmem_read_mapping_page() in
place of read_mapping_page(), since their swap_space has been created with
shmem_file_setup().
Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Thomas Hellstrom <thellstrom@vmware.com> Cc: Dave Airlie <airlied@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: drivers/misc/ioc4.o(.data+0x144): Section mismatch in reference from the variable ioc4_load_modules_work to the function .devinit.text:ioc4_load_modules()
The variable ioc4_load_modules_work references
the function __devinit ioc4_load_modules()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
This one is potentially fatal; by the time ioc4_load_modules is invoked
it may already have been freed. For that reason ioc4_load_modules_work
can't be turned to __devinitdata but also because it's referenced in
ioc4_exit.
WARNING: drivers/leds/leds-lp5523.o(.text+0x12f4): Section mismatch in reference from the function lp5523_probe() to the function .init.text:lp5523_init_led()
The function lp5523_probe() references
the function __init lp5523_init_led().
This is often because lp5523_probe lacks a __init
annotation or the annotation of lp5523_init_led is wrong.
Fixing this one triggers one more mismatch, fix that one as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Cc: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: drivers/leds/leds-lp5521.o(.text+0xf2c): Section mismatch in reference from the function lp5521_probe() to the function .init.text:lp5521_init_led()
The function lp5521_probe() references
the function __init lp5521_init_led().
This is often because lp5521_probe lacks a __init
annotation or the annotation of lp5521_init_led is wrong.
Fixing this mismatch triggers one more mismatch, fix that one as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Cc: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
memcg: fix direct softlimit reclaim to be called in limit path
Commit d149e3b25d7c ("memcg: add the soft_limit reclaim in global direct
reclaim") adds a softlimit hook to shrink_zones(). By this, soft limit
is called as
This will cause a global reclaim when a memcg hits limit.
This is bug. soft_limit_reclaim() should be called when
scanning_global_lru(sc) == true.
And the commit adds a variable "total_scanned" for counting softlimit
scanned pages....it's not "total". This patch removes the variable and
update sc->nr_scanned instead of it. This will affect shrink_slab()'s
scan condition but, global LRU is scanned by softlimit and I think this
change makes sense.
TODO: avoid too much scanning of a zone when softlimit did enough work.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp> Cc: Ying Han <yinghan@google.com> Cc: Michal Hocko <mhocko@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vasiliy Kulikov [Mon, 27 Jun 2011 23:18:11 +0000 (16:18 -0700)]
taskstats: don't allow duplicate entries in listener mode
Currently a single process may register exit handlers unlimited times.
It may lead to a bloated listeners chain and very slow process
terminations.
Eg after 10KK sent TASKSTATS_CMD_ATTR_REGISTER_CPUMASKs ~300 Mb of
kernel memory is stolen for the handlers chain and "time id" shows 2-7
seconds instead of normal 0.003. It makes it possible to exhaust all
kernel memory and to eat much of CPU time by triggerring numerous exits
on a single CPU.
The patch limits the number of times a single process may register
itself on a single CPU to one.
One little issue is kept unfixed - as taskstats_exit() is called before
exit_files() in do_exit(), the orphaned listener entry (if it was not
explicitly deregistered) is kept until the next someone's exit() and
implicit deregistration in send_cpu_listeners(). So, if a process
registered itself as a listener exits and the next spawned process gets
the same pid, it would inherit taskstats attributes.
Jan Kara [Mon, 27 Jun 2011 23:18:10 +0000 (16:18 -0700)]
mm: fix assertion mapping->nrpages == 0 in end_writeback()
Under heavy memory and filesystem load, users observe the assertion
mapping->nrpages == 0 in end_writeback() trigger. This can be caused by
page reclaim reclaiming the last page from a mapping in the following
race:
Josh Hunt [Mon, 27 Jun 2011 23:18:08 +0000 (16:18 -0700)]
drivers/misc/lkdtm.c: fix race when crashpoint is hit multiple times before checking count
We observed the crash point count going negative in cases where the
crash point is hit multiple times before the check of "count == 0" is
done. Because of this we never call lkdtm_do_action(). This patch just
adds a spinlock to protect count.
romfs_get_unmapped_area() checks argument `len' without considering
PAGE_ALIGN which will cause do_mmap_pgoff() return -EINVAL error after
commit f67d9b1576c ("nommu: add page_align to mmap").
Fix the check by changing it in same way ramfs_nommu_get_unmapped_area()
was changed in ramfs/file-nommu.c.
Signed-off-by: Bob Liu <lliubbo@gmail.com> Cc: David Howells <dhowells@redhat.com> Cc: Paul Mundt <lethal@linux-sh.org> Acked-by: Greg Ungerer <gerg@snapgear.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It has 56 bytes of nonvolatile RAM. Its register set is same as that of
rtc device: DS1307.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Acked-by: Timur Tabi <timur@freescale.com> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Mon, 27 Jun 2011 23:18:04 +0000 (16:18 -0700)]
tmpfs: add shmem_read_mapping_page_gfp
Although it is used (by i915) on nothing but tmpfs, read_cache_page_gfp()
is unsuited to tmpfs, because it inserts a page into pagecache before
calling the filesystem's ->readpage: tmpfs may have pages in swapcache
which only it knows how to locate and switch to filecache.
At present tmpfs provides a ->readpage method, and copes with this by
copying pages; but soon we can simplify it by removing its ->readpage.
Provide shmem_read_mapping_page_gfp() now, ready for that transition,
Export shmem_read_mapping_page_gfp() and add it to list in shmem_fs.h,
with shmem_read_mapping_page() inline for the common mapping_gfp case.
(shmem_read_mapping_page_gfp or shmem_read_cache_page_gfp? Generally the
read_mapping_page functions use the mapping's ->readpage, and the
read_cache_page functions use the supplied filler, so I think
read_cache_page_gfp was slightly misnamed.)
Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Christoph Hellwig <hch@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Mon, 27 Jun 2011 23:18:03 +0000 (16:18 -0700)]
tmpfs: take control of its truncate_range
2.6.35's new truncate convention gave tmpfs the opportunity to control
its file truncation, no longer enforced from outside by vmtruncate().
We shall want to build upon that, to handle pagecache and swap together.
Slightly redefine the ->truncate_range interface: let it now be called
between the unmap_mapping_range()s, with the filesystem responsible for
doing the truncate_inode_pages_range() from it - just as the filesystem
is nowadays responsible for doing that from its ->setattr.
Let's rename shmem_notify_change() to shmem_setattr(). Instead of
calling the generic truncate_setsize(), bring that code in so we can
call shmem_truncate_range() - which will later be updated to perform its
own variant of truncate_inode_pages_range().
Remove the punch_hole unmap_mapping_range() from shmem_truncate_range():
now that the COW's unmap_mapping_range() comes after ->truncate_range,
there is no need to call it a third time.
Export shmem_truncate_range() and add it to the list in shmem_fs.h, so
that i915_gem_object_truncate() can call it explicitly in future; get
this patch in first, then update drm/i915 once this is available (until
then, i915 will just be doing the truncate_inode_pages() twice).
Though introduced five years ago, no other filesystem is implementing
->truncate_range, and its only other user is madvise(,,MADV_REMOVE): we
expect to convert it to fallocate(,FALLOC_FL_PUNCH_HOLE,,) shortly,
whereupon ->truncate_range can be removed from inode_operations -
shmem_truncate_range() will help i915 across that transition too.
Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Christoph Hellwig <hch@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Mon, 27 Jun 2011 23:18:02 +0000 (16:18 -0700)]
mm: move shmem prototypes to shmem_fs.h
Before adding any more global entry points into shmem.c, gather such
prototypes into shmem_fs.h. Remove mm's own declarations from swap.h,
but for now leave the ones in mm.h: because shmem_file_setup() and
shmem_zero_setup() are called from various places, and we should not
force other subsystems to update immediately.
Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Christoph Hellwig <hch@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vitaliy Ivanov [Mon, 27 Jun 2011 16:07:08 +0000 (19:07 +0300)]
Fix some kernel-doc warnings
Fix 'make htmldocs' warnings:
Warning(/include/linux/hrtimer.h:153): No description found for parameter 'clockid'
Warning(/include/linux/device.h:604): Excess struct/union/enum/typedef member 'of_match' description in 'device'
Warning(/include/net/sock.h:349): Excess struct/union/enum/typedef member 'sk_rmem_alloc' description in 'sock'
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-beck.git / log