Jubin John [Tue, 12 Apr 2016 18:30:08 +0000 (11:30 -0700)]
IB/hfi1: Change default number of user contexts
Change the default number of user contexts to the number of real
(non-HT) cpu cores in order to reduce the division of hfi1 hardware
contexts in the case of high core counts with hyper-threading enabled.
Reviewed-by: Dean Luick <dean.luick@intel.com> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com> Signed-off-by: Jubin John <jubin.john@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Mike Marciniszyn [Tue, 12 Apr 2016 18:28:56 +0000 (11:28 -0700)]
IB/hfi1: Remove unreachable code
Remove unreachable code from RC ack handling to fix an
smatch error.
Fixes: 633d27399514 ("staging/rdma/hfi1: use mod_timer when appropriate") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Dean Luick [Tue, 12 Apr 2016 18:28:36 +0000 (11:28 -0700)]
IB/hfi1: Fix double QSFP resource acquire on cache refresh
The function refresh_qsfp_cache() acquires the i2c chain resource,
but one caller already holds the resource. Change the acquire so
all calls to refresh_qsfp_cache() are covered by the acquire and
remove the acquire within refresh_qsfp_cache().
Dean Luick [Tue, 12 Apr 2016 18:26:21 +0000 (11:26 -0700)]
IB/hfi1: Guard against concurrent I2C access across all chains
The discrete ASIC board design makes the two I2C chains not
independent of each other. That is, only one chain can safely
be accessed at a time. For discrete ASIC devices, adjust the
resource locking so that access to one I2C chain will lock both
of the chains.
The pre-LNI SerDes and channel tuning algorithm already checks for
module presence assertion for the relevant port types. The extraneous
check removed in this patch blocks link up for port types for which
the module presence assertion is not relevant.
IB/hfi1: Always turn on CDRs for low power QSFP modules
Clock and data recovery mechanisms (CDRs) in active QSFP modules
can be turned on or off to improve the bit error rate observed on
the channel. Signal integrity and bit error rate requirements require
us to always turn on any CDRs present in low power cables (power
dissipation 2.5W or lower). However, we adhere to the platform
designer's settings (provided in the platform configuration) for
higher power cables (dissipation 3.5W or higher) if the platform
designer has determined that the platform requires the CDRs to be
turned on (or off) and is capable of supplying and cooling the higher
power modules.
This patch also introduces the get_qsfp_power_class function to
centralize the bit twiddling required to determine the QSFP power class
across the code. Reusing this function improves the readability of code
that depends on knowing the power class of the cable, such as the
active and optical channel tuning algorithm.
Reviewed-by: Dean Luick <dean.luick@intel.com> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
IB/hfi1: Check P_KEY for all sent packets from user mode
Add the P_KEY check for user-context mechanism for
both PIO and SDMA. For PIO, the
SendCtxtCheckEnable.DisallowKDETHPackets is set by
default. When the P_KEY is set,
SendCtxtCheckEnable.DisallowKDETHPackets is cleared.
For SDMA, a software check was included. This change
requires user processes to set the P_KEY before sending
any packets, otherwise, the sent packet will fail. The
original submission didn't have this check but it's
required.
Reviewed-by: Dean Luick <dean.luick@intel.com> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Reviewed-by: Mikto Haralanov <mitko.haralanov@intel.com> Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Increasing the default MTU size to 10KB improves performance
for PSM. Change the default MTU to 10KB but constrain
Verbs MTU to 8KB. Also update default MTU module parameter
description to be HFI1_DEFAULT_MAX_MTU.
Reviewed-by: Dean Luick <dean.luick@intel.com> Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Reviewed-by: Jubin John <jubin.john@intel.com> Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Dean Luick [Tue, 12 Apr 2016 17:50:35 +0000 (10:50 -0700)]
IB/hfi1: Simplify init_qpmap_table()
Make init_qpmap_table() easier to understand by simplifying
the loop indexing and writing each register when it is "full",
removing the need for a follow-on register write.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Dean Luick [Tue, 12 Apr 2016 17:50:16 +0000 (10:50 -0700)]
IB/hfi1: Remove invalid QOS check
Remove an invalid compare of the number of QOS RSM map table entries
against the number of physical receive contexts. The RSM map table
has its own size and has no relation to the number of physical receive
contexts.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Dean Luick [Tue, 12 Apr 2016 17:50:10 +0000 (10:50 -0700)]
IB/hfi1: Fix QOS num_vl bit width
The bit width for num_vls, n, needs to be calculated based on
the pow2 rounded up of the number of vls. Otherwise num_vls of 3,
5, 6, and 7 will have misplaced QOS RSM map entries.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Dean Luick [Tue, 12 Apr 2016 17:50:04 +0000 (10:50 -0700)]
IB/hfi1: Fix i2c resource reservation checks
The i2c and qsfp read/write routines should check for the resource
reservation of the incoming argument target rather than the implicit
target of the hardware HFI.
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com> Signed-off-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Jubin John <jubin.john@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Jubin John [Wed, 20 Apr 2016 13:05:24 +0000 (06:05 -0700)]
IB/rdmavt,hfi1,qib: Fix memory leak
rdi->ports has memory allocated in rvt_alloc_device(), but does not get
freed because the hfi1 and qib drivers drivers call ib_dealloc_device()
directly instead of going through rdmavt. Add a rvt_dealloc_device()
that frees rdi->ports and then calls ib_dealloc_device(). Switch hfi1
and qib drivers to calling rvt_dealloc_device() instead of
ib_dealloc_device() directly.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Reviewed-by: Brian Welty <brian.welty@intel.com> Signed-off-by: Jubin John <jubin.john@intel.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
IB/hfi1: Fix buffer cache races which may cause corruption
There are two possible causes for node/memory corruption both
of which are related to the cache eviction algorithm. One way
to cause corruption is due to the asynchronous nature of the
MMU invalidation and the locking used when invalidating node.
The MMU invalidation routine would temporarily release the
RB tree lock to avoid a deadlock. However, this would allow
the eviction function to take the lock resulting in the removal
of cache nodes.
If the node being removed by the eviction code is the same as
the node being invalidated, the result is use after free.
The same is true in the other direction due to the temporary
release of the eviction list lock in the eviction loop.
Another corner case exists when dealing with the SDMA buffer
cache that could cause memory corruption of kernel memory.
The most common way, in which this corruption exhibits itself
is a linked list node corruption. In that case, the kernel will
complain that a node with poisoned pointers is being removed.
The fact that the pointers are already poisoned means that the
node has already been removed from the list.
To root cause of this corruption was a mishandling of the
eviction list maintained by the driver. In order for this
to happen four conditions need to be satisfied:
1. A node describing a user buffer already exists in the
interval RB tree,
2. The beginning of the current user buffer matches that
node but is bigger. This will cause the node to be
extended.
3. The amount of cached buffers is close or at the limit
of the buffer cache size.
4. The node has dropped close to the end of the eviction
list. This will cause the node to be considered for
eviction.
If all of the above conditions have been satisfied, it is
possible for the eviction algorithm to evict the current node,
which will free the node without the driver knowing.
To solve both issues described above:
- the locking around the MMU invalidation loop and cache
eviction loop has been improved so locks are not released in
the loop body,
- a new RB function is introduced which will "atomically" find
and remove the matching node from the RB tree, preventing the
MMU invalidation loop from touching it, and
- the node being extended by the pin_vector_pages() function is
removed from the eviction list prior to calling the eviction
function.
IB/hfi1: Extract and reinsert MMU RB node on lookup
The page pinning function, which also maintains the pin cache,
behaves one of two ways when an exact buffer match is not found:
1. If no node is not found (a buffer with the same starting address
is not found in the cache), a new node is created, the buffer
pages are pinned, and the node is inserted into the RB tree, or
2. If a node is found but the buffer in that node is a subset of
the new user buffer, the node is extended with the new buffer
pages.
Both modes of operation require (re-)insertion into the interval RB
tree.
When the node being inserted is a new node, the operations are pretty
simple. However, when the node is already existing and is being
extended, special care must be taken.
First, we want to guard against an asynchronous attempt to
delete the node by the MMU invalidation notifier. The simplest way to
do this is to remove the node from the RB tree, preventing the search
algorithm from finding it.
Second, the node needs to be re-inserted so it lands in the proper place
in the tree and the tree is correctly re-balanced. This also requires
the node to be removed from the RB tree.
This commit adds the hfi1_mmu_rb_extract() function, which will search
for a node in the interval RB tree matching an address and length and
remove it from the RB tree if found. This allows for both of the above
special cases be handled in a single step.
Reviewed-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Mitko Haralanov <mitko.haralanov@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
The computation of the interval of an interval RB node
was incorrect leading to data corruption due to the RB
search algorithm not properly finding the all RB nodes
in an MMU invalidation interval.
The problem stemmed from the fact that the beginning
address of the node's range was being aligned to a page
boundary. For certain buffer sizes, this would lead to
a end address calculation that was off by 1 page.
An important aspect of keeping the RB same is also
updating the node's range in the case it's being extended.
IB/hfi1: Protect the interval RB tree when cleaning up
The current implementation of the clean up function for
the interval RB trees has two flaws which may cause
problems in cases of concurrent executing of the function
and MMU notifier.
The flaws were due to the fact that deregistration of the
MMU callbacks was done after the tree was emptied and,
furthermore, the tree was not being locked.
This commit fixes both of these flaws by, first, switch the
order of operations, and, second, locking the tree while
traversing it to prevent any other operations.
The driver had two memory leaks - one in the user
expected receive code and one in SDMA buffer cache.
The leak in the expected receive code only showed up
when the user/admin had set ulimit sufficiently low
and the driver did not have enough room in the cache
before hitting the limit of allowed cachable memory.
When this condition occurred, the driver returned
early signaling userland that it needed to free some
buffers to free up room in the cache.
The bug was that the driver was not cleaning up
allocated memory prior to returning early.
The leak in the SDMA buffer cache could occur (even
though it never did), when the insertion of a buffer
node in the interval RB tree failed. In this case, the
driver failed to unpin the pages of the node instead
erroneously returning success.
IB/hfi1: Don't remove list entries if they are not in a list
The SDMA cache logic maintains an eviction list which is ordered
by most recently used user buffers. Upon errors or buffer freeing,
the list nodes were unconditionally being deleted. This would lead
to list corruption warnings if the nodes were never inserted in the
eviction list to begin with.
This commit prevents this by checking that the nodes are already
part of the eviction list.
Reviewed-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Mitko Haralanov <mitko.haralanov@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Mike Marciniszyn [Tue, 12 Apr 2016 17:46:10 +0000 (10:46 -0700)]
IB/qib, IB/hfi1: Fix up UD loopback use of irq flags
The dual lock patch moved locking around and missed an issue
with handling irq flags when processing UD loopback
packets. This issue was revealed by smatch.
Fix for both qib and hfi1 to pass the saved flags to the UD request
builder and handle the changes correctly.
Fixes: 46a80d62e6e0 ("IB/qib, staging/rdma/hfi1: add s_hlock for use in post send") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Jason Gunthorpe [Mon, 11 Apr 2016 01:13:13 +0000 (19:13 -0600)]
IB/security: Restrict use of the write() interface
The drivers/infiniband stack uses write() as a replacement for
bi-directional ioctl(). This is not safe. There are ways to
trigger write calls that result in the return structure that
is normally written to user space being shunted off to user
specified kernel memory instead.
For the immediate repair, detect and deny suspicious accesses to
the write API.
For long term, update the user space libraries and the kernel API
to something that doesn't present the same security vulnerabilities
(likely a structured ioctl() interface).
The impacted uAPI interfaces are generally only available if
hardware from drivers/infiniband is installed in the system.
Reported-by: Jann Horn <jann@thejh.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[ Expanded check to all known write() entry points ] Cc: stable@vger.kernel.org Signed-off-by: Doug Ledford <dledford@redhat.com>
Dean Luick [Fri, 22 Apr 2016 18:17:03 +0000 (11:17 -0700)]
IB/hfi1: Use kernel default llseek for ui device
The ui device llseek had a mistake with SEEK_END and did
not fully follow seek semantics. Correct all this by
using a kernel supplied function for fixed size devices.
Cc: Al Viro <viro@ZenIV.linux.org.uk> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
This commit re-arranges the context initialization code in a way that
would allow for context event flags to be used to determine whether
the context has been successfully initialized.
In turn, this can be used to skip the resource de-allocation if they
were never allocated in the first place.
Fixes: 3abb33ac6521 ("staging/hfi1: Add TID cache receive init and free funcs") Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Mitko Haralanov <mitko.haralanov@intel.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com. Signed-off-by: Doug Ledford <dledford@redhat.com>
Jubin John [Tue, 12 Apr 2016 17:47:00 +0000 (10:47 -0700)]
IB/rdmavt: Fix send scheduling
call_send is used to determine whether to send immediately or schedule
a send for later. The current logic in rdmavt is inverted and has a
negative impact on the latency of the hfi1 and qib drivers. Fix this
regression by correctly calling send immediately when call_send is set.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Jubin John <jubin.john@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
IB/hfi1: Fix deadlock caused by locking with wrong scope
The locking around the interval RB tree is designed to prevent
access to the tree while it's being modified. The locking in its
current form is too overzealous, which is causing a deadlock in
certain cases with the following backtrace:
As evident from the backtrace above, the process was being put to sleep
while holding the lock.
Limiting the scope of the lock only to the RB tree operation fixes the
above error allowing for proper locking and the process being put to
sleep when needed.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Reviewed-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Mitko Haralanov <mitko.haralanov@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
IB/hfi1: Prevent NULL pointer deferences in caching code
There is a potential kernel crash when the MMU notifier calls the
invalidation routines in the hfi1 pinned page caching code for sdma.
The invalidation routine could call the remove callback
for the node, which in turn ends up dereferencing the
current task_struct to get a pointer to the mm_struct.
However, the mm_struct pointer could be NULL resulting in
the following backtrace:
To correct this, the mm_struct passed to us by the MMU notifier is
used (which is what should have been done to begin with). This avoids
the broken derefences and ensures that the correct mm_struct is used.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Reviewed-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Mitko Haralanov <mitko.haralanov@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Sagi Grimberg [Thu, 31 Mar 2016 16:03:25 +0000 (19:03 +0300)]
IB/mlx5: Expose correct max_sge_rd limit
mlx5 devices (Connect-IB, ConnectX-4, ConnectX-4-LX) has a limitation
where rdma read work queue entries cannot exceed 512 bytes.
A rdma_read wqe needs to fit in 512 bytes:
- wqe control segment (16 bytes)
- rdma segment (16 bytes)
- scatter elements (16 bytes each)
So max_sge_rd should be: (512 - 16 - 16) / 16 = 30.
Cc: linux-stable@vger.kernel.org Reported-by: Christoph Hellwig <hch@lst.de> Tested-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagig@grimberg.me> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Merge branch 'for-4.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fix from Tejun Heo:
"So, it turns out we had a silly bug in the most fundamental part of
workqueue for a very long time. AFAICS, this dates back to pre-git
era and has quite likely been there from the time workqueue was first
introduced.
A work item uses its PENDING bit to synchronize multiple queuers.
Anyone who wins the PENDING bit owns the pending state of the work
item. Whether a queuer wins or loses the race, one thing should be
guaranteed - there will soon be at least one execution of the work
item - where "after" means that the execution instance would be able
to see all the changes that the queuer has made prior to the queueing
attempt.
Unfortunately, we were missing a smp_mb() after clearing PENDING for
execution, so nothing guaranteed visibility of the changes that a
queueing loser has made, which manifested as a reproducible blk-mq
stall.
Lots of kudos to Roman for debugging the problem. The patch for
-stable is the minimal one. For v3.7, Peter is working on a patch to
make the code path slightly more efficient and less fragile"
* 'for-4.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: fix ghost PENDING flag while doing MQ IO
Merge branch 'for-4.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"Two patches to fix a deadlock which can be easily triggered if memcg
charge moving is used.
This bug was introduced while converting threadgroup locking to a
global percpu_rwsem and is caused by cgroup controller task migration
path depending on the ability to create new kthreads. cpuset had a
similar issue which was fixed by performing heavy-lifting operations
asynchronous to task migration. The two patches fix the same issue in
memcg in a similar way. The first patch makes the mechanism generic
and the second relocates memcg charge moving outside the migration
path.
Given that we don't want to perform heavy operations while
writelocking threadgroup lock anyway, moving them out of the way is a
desirable solution. One thing to note is that the problem was
difficult to debug because lockdep couldn't figure out the deadlock
condition. Looking into how to improve that"
* 'for-4.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
memcg: relocate charge moving from ->attach to ->post_attach
cgroup, cpuset: replace cpuset_post_attach_flush() with cgroup_subsys->post_attach callback
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has one buildfix, one ABBA deadlock fix, and three simple 'add ID'
patches"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: exynos5: Fix possible ABBA deadlock by keeping I2C clock prepared
i2c: cpm: Fix build break due to incompatible pointer types
i2c: ismt: Add Intel DNV PCI ID
i2c: xlp9xx: add support for Broadcom Vulcan
i2c: rk3x: add support for rk3228
* tag 'arc-4.6-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: add support for reserved memory defined by device tree
ARC: support generic per-device coherent dma mem
Documentation: dt: arc: fix spelling mistakes
ARCv2: Enable LOCKDEP
Merge tag 'nios2-v4.6-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2
Pull arch/nios2 fix from Ley Foon Tan:
"memset: use the right constraint modifier for the %4 output operand"
* tag 'nios2-v4.6-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
nios2: memset: use the right constraint modifier for the %4 output operand
Merge tag 'platform-drivers-x86-v4.6-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fix from Darren Hart:
"Fix regression caused by hotkey enabling value in toshiba_acpi"
* tag 'platform-drivers-x86-v4.6-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
toshiba_acpi: Fix regression caused by hotkey enabling value
nios2: memset: use the right constraint modifier for the %4 output operand
Depending on the size of the area to be memset'ed, the nios2 memset implementation
either uses a naive loop (for buffers smaller or equal than 8 bytes) or a more optimized
implementation (for buffers larger than 8 bytes). This implementation does 4-byte stores
rather than 1-byte stores to speed up memset.
However, we discovered that on our nios2 platform, memset() was not properly setting the
buffer to the expected value. A memset of 0xff would not set the entire buffer to 0xff, but to:
0xff 0x00 0xff 0x00 0xff 0x00 0xff 0x00 ...
Which is obviously incorrect. Our investigation has revealed that the problem lies in the
incorrect constraints used in the inline assembly.
The following piece of assembly, from the nios2 memset implementation, is supposed to
create a 4-byte value that repeats 4 times the 1-byte pattern passed as memset argument:
This is wrong because r5 gets used both for %5 and %4, which leads to the final pattern
stored in r4 to be 0xff00ff00 rather than the expected 0xffffffff.
%4 is defined with the "=r" constraint, i.e as an output operand. However, as explained in
http://www.ethernut.de/en/documents/arm-inline-asm.html, this does not prevent gcc from
using the same register for an output operand (%4) and input operand (%5). By using the
constraint modifier '&', we indicate that the register should be used for output only. With this
change, we get the following assembly output:
Which correctly produces the 0xffffffff pattern when 0xff is passed as the memset() pattern.
It is worth mentioning the observed consequence of this bug: we were hitting the kernel
BUG() in mm/bootmem.c:__free() that verifies when marking a page as free that it was
previously marked as occupied (i.e that the bit was set to 1). The entire bootmem bitmap is
set to 0xff bit via a memset() during the bootmem initialization. The bootmem_free() call right
after the initialization was finding some bits to be set to 0, which didn't make sense since the
bitmap has just been memset'ed to 0xff. Except that due to the bug explained above, the
bitmap was in fact initialized to 0xff00ff00.
Thanks to Marek Vasut for his help and feedback.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Ley Foon Tan <lftan@altera.com>
1) Handle v4/v6 mixed sockets properly in soreuseport, from Craig
Gallak.
2) Bug fixes for the new macsec facility (missing kmalloc NULL checks,
missing locking around netdev list traversal, etc.) from Sabrina
Dubroca.
3) Fix handling of host routes on ifdown in ipv6, from David Ahern.
4) Fix double-fdput in bpf verifier. From Jann Horn.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (31 commits)
bpf: fix double-fdput in replace_map_fd_with_map_ptr()
net: ipv6: Delete host routes on an ifdown
Revert "ipv6: Revert optional address flusing on ifdown."
net/mlx4_en: fix spurious timestamping callbacks
net: dummy: remove note about being Y by default
cxgbi: fix uninitialized flowi6
ipv6: Revert optional address flusing on ifdown.
ipv4/fib: don't warn when primary address is missing if in_dev is dead
net/mlx5: Add pci shutdown callback
net/mlx5_core: Remove static from local variable
net/mlx5e: Use vport MTU rather than physical port MTU
net/mlx5e: Fix minimum MTU
net/mlx5e: Device's mtu field is u16 and not int
net/mlx5_core: Add ConnectX-5 to list of supported devices
net/mlx5e: Fix MLX5E_100BASE_T define
net/mlx5_core: Fix soft lockup in steering error flow
qlcnic: Update version to 5.3.64
net: stmmac: socfpga: Remove re-registration of reset controller
macsec: fix netlink attribute validation
macsec: add missing macsec prefix in uapi
...
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are the latest bug fixes for ARM SoCs, mostly addressing recent
regressions. Changes are across several platforms, so I'm listing
every change separately here.
Regressions since 4.5:
- A correction of the psci firmware DT binding, to prevent users from
relying on unintended semantics
- Actually getting the newly merged clock driver for some OMAP
platforms to work
- A revert of patches for the Qualcomm BAM, these need to be reworked
for 4.7 to avoid breaking boards other than the one they were
intended for
- A correction for the I2C device nodes on the Socionext Uniphier
platform
- i.MX SDHCI was broken for non-DT platforms due to a change with the
setting of the DMA mask
- A revert of a patch that accidentally added a nonexisting clock on
the Rensas "Porter" board
- A couple of OMAP fixes that are all related to suspend after the
power domain changes for dra7
- On Mediatek, revert part of the power domain initialization changes
that broke mt8173-evb
Fixes for older bugs:
- Workaround for an "external abort" in the omap34xx suspend/resume
code.
- The USB1/eSATA should not be listed as an excon device on
am57xx-beagle-x15 (broken since v4.0)
- A v4.5 regression in the TI AM33xx and AM43XX DT specifying
incorrect DMA request lines for the GPMC
- The jiffies calibration on Renesas platforms was incorrect for some
modern CPU cores.
- A hardware errata woraround for clockdomains on TI DRA7"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
drivers: firmware: psci: unify enable-method binding on ARM {64,32}-bit systems
arm64: dts: uniphier: fix I2C nodes of PH1-LD20
ARM: shmobile: timer: Fix preset_lpj leading to too short delays
Revert "ARM: dts: porter: Enable SCIF_CLK frequency and pins"
ARM: dts: r8a7791: Don't disable referenced optional clocks
Revert "ARM: OMAP: Catch callers of revision information prior to it being populated"
ARM: OMAP3: Fix external abort on 36xx waking from off mode idle
ARM: dts: am57xx-beagle-x15: remove extcon_usb1
ARM: dts: am437x: Fix GPMC dma properties
ARM: dts: am33xx: Fix GPMC dma properties
Revert "soc: mediatek: SCPSYS: Fix double enabling of regulators"
ARM: mach-imx: sdhci-esdhc-imx: initialize DMA mask
ARM: DRA7: clockdomain: Implement timer workaround for errata i874
ARM: OMAP: Catch callers of revision information prior to it being populated
ARM: dts: dra7: Correct clock tree for sys_32k_ck
ARM: OMAP: DRA7: Provide proper class to omap2_set_globals_tap
ARM: OMAP: DRA7: wakeupgen: Skip SAR save for wakeupgen
Revert "dts: msm8974: Add dma channels for blsp2_i2c1 node"
Revert "dts: msm8974: Add blsp2_bam dma node"
ARM: dts: Add clocks for dm814x ADPLL
This is more prep-work for the upcoming pty changes. Still just code
cleanup with no actual semantic changes.
This removes a bunch pointless complexity by just having the slave pty
side remember the dentry associated with the devpts slave rather than
the inode. That allows us to remove all the "look up the dentry" code
for when we want to remove it again.
Together with moving the tty pointer from "inode->i_private" to
"dentry->d_fsdata" and getting rid of pointless inode locking, this
removes about 30 lines of code. Not only is the end result smaller,
it's simpler and easier to understand.
The old code, for example, depended on the d_find_alias() to not just
find the dentry, but also to check that it is still hashed, which in
turn validated the tty pointer in the inode.
That is a _very_ roundabout way to say "invalidate the cached tty
pointer when the dentry is removed".
The new code just does
dentry->d_fsdata = NULL;
in devpts_pty_kill() instead, invalidating the tty pointer rather more
directly and obviously. Don't do something complex and subtle when the
obvious straightforward approach will do.
The rest of the patch (ie apart from code deletion and the above tty
pointer clearing) is just switching the calling convention to pass the
dentry or file pointer around instead of the inode.
Cc: Eric Biederman <ebiederm@xmission.com> Cc: Peter Anvin <hpa@zytor.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Peter Hurley <peter@hurleysoftware.com> Cc: Serge Hallyn <serge.hallyn@ubuntu.com> Cc: Willy Tarreau <w@1wt.eu> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk> Cc: Jann Horn <jann@thejh.net> Cc: Greg KH <greg@kroah.com> Cc: Jiri Slaby <jslaby@suse.com> Cc: Florian Weimer <fw@deneb.enyo.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bpf: fix double-fdput in replace_map_fd_with_map_ptr()
When bpf(BPF_PROG_LOAD, ...) was invoked with a BPF program whose bytecode
references a non-map file descriptor as a map file descriptor, the error
handling code called fdput() twice instead of once (in __bpf_map_get() and
in replace_map_fd_with_map_ptr()). If the file descriptor table of the
current task is shared, this causes f_count to be decremented too much,
allowing the struct file to be freed while it is still in use
(use-after-free). This can be exploited to gain root privileges by an
unprivileged user.
This bug was introduced in
commit 0246e64d9a5f ("bpf: handle pseudo BPF_LD_IMM64 insn"), but is only
exploitable since
commit 1be7f75d1668 ("bpf: enable non-root eBPF programs") because
previously, CAP_SYS_ADMIN was required to reach the vulnerable code.
(posted publicly according to request by maintainer)
Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad S [Tue, 5 Apr 2016 04:53:48 +0000 (10:23 +0530)]
RDMA/iw_cxgb4: Fix bar2 virt addr calculation for T4 chips
For T4, kernel mode qps don't use the user doorbell. User mode qps during
flow control db ringing are forced into kernel, where user doorbell is
treated as kernel doorbell and proper bar2 offset in bar2 virtual space is
calculated, which incase of T4 is a bogus address, causing a kernel panic
due to illegal write during doorbell ringing.
In case of T4, kernel mode qp bar2 virtual address should be 0. Added T4
check during bar2 virtual address calculation to return 0. Fixed Bar2
range checks based on bar2 physical address.
Steve Wise [Tue, 12 Apr 2016 13:55:01 +0000 (06:55 -0700)]
iw_cxgb3: initialize ibdev.iwcm->ifname for port mapping
The IWCM uses ibdev.iwcm->ifname for registration with the iwarp
port map daemon. But iw_cxgb3 did not initialize this field which
causes intermittent registration failures based on the contents of the
uninitialized memory.
Fixes: c1340e8aa628 ("iw_cxgb3: support for iWARP port mapping") Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Steve Wise [Tue, 12 Apr 2016 13:54:54 +0000 (06:54 -0700)]
iw_cxgb4: initialize ibdev.iwcm->ifname for port mapping
The IWCM uses ibdev.iwcm->ifname for registration with the iwarp
port map daemon. But iw_cxgb4 did not initialize this field which
causes intermittent registration failures based on the contents of the
uninitialized memory.
Fixes: 170003c894d9 ("iw_cxgb4: remove port mapper related code") Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
The drain_rq function expects a normal receive qp to drain. A qp can
only have either a normal rq or an srq. If there is an srq, there
is no rq to drain. Until the API supports draining SRQs, simply
skip draining the rq when the qp has an srq attached.
Fixes: 765d67748bcf ("IB: new common API for draining queues") Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Doug Ledford <dledford@redhat.com>
David Ahern [Fri, 22 Apr 2016 03:56:12 +0000 (20:56 -0700)]
net: ipv6: Delete host routes on an ifdown
It was a simple idea -- save IPv6 configured addresses on a link down
so that IPv6 behaves similar to IPv4. As always the devil is in the
details and the IPv6 stack as too many behavioral differences from IPv4
making the simple idea more complicated than it needs to be.
The current implementation for keeping IPv6 addresses can panic or spit
out a warning in one of many paths:
1. IPv6 route gets an IPv4 route as its 'next' which causes a panic in
rt6_fill_node while handling a route dump request.
2. rt->dst.obsolete is set to DST_OBSOLETE_DEAD hitting the WARN_ON in
fib6_del
3. Panic in fib6_purge_rt because rt6i_ref count is not 1.
The root cause of all these is references related to the host route for
an address that is retained.
So, this patch deletes the host route every time the ifdown loop runs.
Since the host route is deleted and will be re-generated an up there is
no longer a need for the l3mdev fix up. On the 'admin up' side move
addrconf_permanent_addr into the NETDEV_UP event handling so that it
runs only once versus on UP and CHANGE events.
All of the current panics and warnings appear to be related to
addresses on the loopback device, but given the catastrophic nature when
a bug is triggered this patch takes the conservative approach and evicts
all host routes rather than trying to determine when it can be re-used
and when it can not. That can be a later optimizaton if desired.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ok, this puts the feature back. I've decided to apply David A.'s
bug fix and run with that rather than make everyone wait another
whole release for this feature.
Signed-off-by: David S. Miller <davem@davemloft.net>
So blk_flush_plug_list() was called with from_schedule == true.
If from_schedule is true, that means that finally blk_mq_insert_requests()
offloads execution of __blk_mq_run_hw_queue() and uses kblockd workqueue,
i.e. it calls kblockd_schedule_delayed_work_on().
That means, that we race with another CPU, which is about to execute
__blk_mq_run_hw_queue() work.
Further debugging shows the following traces from different CPUs:
CPU#0 CPU#1
---------------------------------- -------------------------------
reqeust A inserted
STORE hctx->ctx_map[0] bit marked
kblockd_schedule...() returns 1
<schedule to kblockd workqueue>
request B inserted
STORE hctx->ctx_map[1] bit marked
kblockd_schedule...() returns 0
*** WORK PENDING bit is cleared ***
flush_busy_ctxs() is executed, but
bit 1, set by CPU#1, is not observed
As a result request B pended forever.
This behaviour can be explained by speculative LOAD of hctx->ctx_map on
CPU#0, which is reordered with clear of PENDING bit and executed _before_
actual STORE of bit 1 on CPU#1.
The proper fix is an explicit full barrier <mfence>, which guarantees
that clear of PENDING bit is to be executed before all possible
speculative LOADS or STORES inside actual work function.
Signed-off-by: Roman Pen <roman.penyaev@profitbricks.com> Cc: Gioh Kim <gi-oh.kim@profitbricks.com> Cc: Michael Wang <yun.wang@profitbricks.com> Cc: Tejun Heo <tj@kernel.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: linux-block@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Tejun Heo <tj@kernel.org>
drivers: firmware: psci: unify enable-method binding on ARM {64,32}-bit systems
Currently ARM CPUs DT bindings allows different enable-method value for
PSCI based systems. On ARM 64-bit this property is required and must be
"psci" while on ARM 32-bit systems this property is optional and must
be "arm,psci" if present.
However, "arm,psci" has always been the compatible string for the PSCI
node, and was never intended to be the enable-method. So this is a bug
in the binding and not a deliberate attempt at specifying 32-bit
differently.
This is problematic if 32-bit OS is run on 64-bit system which has
"psci" as enable-method rather than the expected "arm,psci".
So let's unify the value into "psci" and remove support for "arm,psci"
before it finds any users.
Reported-by: Soby Mathew <Soby.Mathew@arm.com> Cc: Rob Herring <robh+dt@kernel.org> Acked-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Eric Dumazet [Sat, 23 Apr 2016 18:35:46 +0000 (11:35 -0700)]
net/mlx4_en: fix spurious timestamping callbacks
When multiple skb are TX-completed in a row, we might incorrectly keep
a timestamp of a prior skb and cause extra work.
Fixes: ec693d47010e8 ("net/mlx4_en: Add HW timestamping (TS) support") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_route_output looks into different fields in the passed flowi6 structure,
yet cxgbi passes garbage in nearly all those fields. Zero the structure out
first.
Fixes: fc8d0590d9142 ("libcxgbi: Add ipv6 api to driver") Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
memcg: relocate charge moving from ->attach to ->post_attach
Hello,
So, this ended up a lot simpler than I originally expected. I tested
it lightly and it seems to work fine. Petr, can you please test these
two patches w/o the lru drain drop patch and see whether the problem
is gone?
Thanks.
------ 8< ------
If charge moving is used, memcg performs relabeling of the affected
pages from its ->attach callback which is called under both
cgroup_threadgroup_rwsem and thus can't create new kthreads. This is
fragile as various operations may depend on workqueues making forward
progress which relies on the ability to create new kthreads.
There's no reason to perform charge moving from ->attach which is deep
in the task migration path. Move it to ->post_attach which is called
after the actual migration is finished and cgroup_threadgroup_rwsem is
dropped.
* move_charge_struct->mm is added and ->can_attach is now responsible
for pinning and recording the target mm. mem_cgroup_clear_mc() is
updated accordingly. This also simplifies mem_cgroup_move_task().
* mem_cgroup_move_task() is now called from ->post_attach instead of
->attach.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@kernel.org> Debugged-and-tested-by: Petr Mladek <pmladek@suse.com> Reported-by: Cyril Hrubis <chrubis@suse.cz> Reported-by: Johannes Weiner <hannes@cmpxchg.org> Fixes: 1ed1328792ff ("sched, cgroup: replace signal_struct->group_rwsem with a global percpu_rwsem") Cc: <stable@vger.kernel.org> # 4.4+
cgroup, cpuset: replace cpuset_post_attach_flush() with cgroup_subsys->post_attach callback
Since e93ad19d0564 ("cpuset: make mm migration asynchronous"), cpuset
kicks off asynchronous NUMA node migration if necessary during task
migration and flushes it from cpuset_post_attach_flush() which is
called at the end of __cgroup_procs_write(). This is to avoid
performing migration with cgroup_threadgroup_rwsem write-locked which
can lead to deadlock through dependency on kworker creation.
memcg has a similar issue with charge moving, so let's convert it to
an official callback rather than the current one-off cpuset specific
function. This patch adds cgroup_subsys->post_attach callback and
makes cpuset register cpuset_post_attach_flush() as its ->post_attach.
The conversion is mostly one-to-one except that the new callback is
called under cgroup_mutex. This is to guarantee that no other
migration operations are started before ->post_attach callbacks are
finished. cgroup_mutex is one of the outermost mutex in the system
and has never been and shouldn't be a problem. We can add specialized
synchronization around __cgroup_procs_write() but I don't think
there's any noticeable benefit.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Li Zefan <lizefan@huawei.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: <stable@vger.kernel.org> # 4.4+ prerequisite for the next patch
toshiba_acpi: Fix regression caused by hotkey enabling value
Commit 52cbae0127ad ("toshiba_acpi: Change default Hotkey enabling value")
changed the hotkeys enabling value, as it was the same value Windows uses,
however, it turns out that the value tells the EC that the driver will now
take care of the hardware events like the physical RFKill switch or the
pointing device toggle button.
This patch reverts such commit by changing the default hotkey enabling
value to 0x09, which enables hotkey events only, making the hardware
buttons working again.
Fixes bugs 113331 and 114941.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes a couple of regressions in the talitos driver that were
introduced back in 4.3.
The first bug causes a crash when the driver's AEAD functionality is
used while the second bug prevents its AEAD feature from working once
you get past the first bug"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: talitos - fix AEAD tcrypt tests
crypto: talitos - fix crash in talitos_cra_init()
Kevin Hilman [Mon, 25 Apr 2016 15:55:17 +0000 (08:55 -0700)]
Merge tag 'omap-for-v4.6/dt-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Enable dm814x and dra62x clock driver. This branch has a dependency
to the clk-ti branch from the Linux clk tree for the ADPLL clock driver.
Otherwise things won't keep booting properly when we flip over to use
the clock driver instead of fixed clocks set up by the bootloader.
* tag 'omap-for-v4.6/dt-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add clocks for dm814x ADPLL
Paolo Abeni [Thu, 21 Apr 2016 20:23:31 +0000 (22:23 +0200)]
ipv4/fib: don't warn when primary address is missing if in_dev is dead
After commit fbd40ea0180a ("ipv4: Don't do expensive useless work
during inetdev destroy.") when deleting an interface,
fib_del_ifaddr() can be executed without any primary address
present on the dead interface.
The above is safe, but triggers some "bug: prim == NULL" warnings.
This commit avoids warning if the in_dev is dead
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 24 Apr 2016 18:51:50 +0000 (14:51 -0400)]
Merge branch 'mlx5-fixes'
Saeed Mahameed says:
====================
mlx5 driver updates and fixes
Changes from V0:
- Dropped: ("net/mlx5e: Reset link modes upon setting speed to zero")
- Fixed compilation issue introduced to mlx5_ib driver.
- Rebased to df637193906a ('Revert "Prevent NUll pointer dereference with two PHYs on cpsw"')
This series has few bug fixes for mlx5 core and ethernet driver.
Eli fixed a wrong static local variable declaration in flow steering API.
Majd added the support of ConnectX-5 PF and VF and added the support
for kernel shutdown pci callback for more robust reboot procedures.
Maor fixed a soft lockup in flow steering.
Rana fixed a wrog speed define in mlx5 EN driver.
I also had the chance to introduce some bug fixes in mlx5 EN mtu
reporting and handling.
For -stable:
net/mlx5_core: Fix soft lockup in steering error flow
net/mlx5e: Device's mtu field is u16 and not int
net/mlx5e: Fix minimum MTU
net/mlx5e: Use vport MTU rather than physical port MTU
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Majd Dibbiny [Thu, 21 Apr 2016 21:33:07 +0000 (00:33 +0300)]
net/mlx5: Add pci shutdown callback
This patch introduces kexec support for mlx5.
When switching kernels, kexec() calls shutdown, which unloads
the driver and cleans its resources.
In addition, remove unregister netdev from shutdown flow. This will
allow a clean shutdown, even if some netdev clients did not release their
reference from this netdev. Releasing The HW resources only is enough as
the kernel is shutting down
Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen [Thu, 21 Apr 2016 21:33:06 +0000 (00:33 +0300)]
net/mlx5_core: Remove static from local variable
The static is not required and breaks re-entrancy if it will be required.
Fixes: 2530236303d9 ("net/mlx5_core: Flow steering tree initialization") Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5e: Use vport MTU rather than physical port MTU
Set and report vport MTU rather than physical MTU,
Driver will set both vport and physical port mtu and will
rely on the query of vport mtu.
SRIOV VFs have to report their MTU to their vport manager (PF),
and this will allow them to work with any MTU they need
without failing the request.
Also for some cases where the PF is not a port owner, PF can
work with MTU less than the physical port mtu if set physical
port mtu didn't take effect.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
For set/query MTU port firmware commands the MTU field
is 16 bits, here I changed all the "int mtu" parameters
of the functions wrapping those firmware commands to be u16.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Majd Dibbiny [Thu, 21 Apr 2016 21:33:02 +0000 (00:33 +0300)]
net/mlx5_core: Add ConnectX-5 to list of supported devices
Add the upcoming ConnectX-5 devices (PF and VF) to the list of
supported devices by the mlx5 driver.
Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bit 25 of eth_proto_capability in PTYS register is
1000Base-TT and not 100Base-T.
Fixes: f62b8bb8f2d3 ('net/mlx5: Extend mlx5_core to
support ConnectX-4 Ethernet functionality') Signed-off-by: Rana Shahout <ranas@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maor Gottlieb [Thu, 21 Apr 2016 21:33:00 +0000 (00:33 +0300)]
net/mlx5_core: Fix soft lockup in steering error flow
In the error flow of adding flow rule to auto-grouped flow
table, we call to tree_remove_node.
tree_remove_node locks the node's parent, however the node's parent
is already locked by mlx5_add_flow_rule and this causes a deadlock.
After this patch, if we failed to add the flow rule, we unlock the
flow table before calling to tree_remove_node.
fixes: f0d22d187473 ('net/mlx5_core: Introduce flow steering autogrouped
flow table') Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Reported-by: Amir Vadai <amir@vadai.me> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Vasut [Thu, 21 Apr 2016 12:11:50 +0000 (14:11 +0200)]
net: stmmac: socfpga: Remove re-registration of reset controller
Both socfpga_dwmac_parse_data() in dwmac-socfpga.c and stmmac_dvr_probe()
in stmmac_main.c functions call devm_reset_control_get() to register an
reset controller for the stmmac. This results in an attempt to register
two reset controllers for the same non-shared reset line.
The first attempt to register the reset controller works fine. The second
attempt fails with warning from the reset controller core, see below.
The warning is produced because the reset line is non-shared and thus
it is allowed to have only up-to one reset controller associated with
that reset line, not two or more.
The solution has multiple parts. First, the original socfpga_dwmac_init()
is tweaked to use reset controller pointer from the stmmac_priv (private
data of the stmmac core) instead of the local instance, which was used
before. The local re-registration of the reset controller is removed.
Next, the socfpga_dwmac_init() is moved after stmmac_dvr_probe() in the
probe function. This order is legal according to Altera and it makes the
code much easier, since there is no need to temporarily register and
unregister the reset controller ; the reset controller is already registered
by the stmmac_dvr_probe().
Finally, plat_dat->exit and socfpga_dwmac_exit() is no longer necessary,
since the functionality is already performed by the stmmac core.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at drivers/reset/core.c:187 __of_reset_control_get+0x218/0x270
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.6.0-rc4-next-20160419-00015-gabb2477-dirty #4
Hardware name: Altera SOCFPGA
[<c010f290>] (unwind_backtrace) from [<c010b82c>] (show_stack+0x10/0x14)
[<c010b82c>] (show_stack) from [<c0373da4>] (dump_stack+0x94/0xa8)
[<c0373da4>] (dump_stack) from [<c011bcc0>] (__warn+0xec/0x104)
[<c011bcc0>] (__warn) from [<c011bd88>] (warn_slowpath_null+0x20/0x28)
[<c011bd88>] (warn_slowpath_null) from [<c03a6eb4>] (__of_reset_control_get+0x218/0x270)
[<c03a6eb4>] (__of_reset_control_get) from [<c03a701c>] (__devm_reset_control_get+0x54/0x90)
[<c03a701c>] (__devm_reset_control_get) from [<c041fa30>] (stmmac_dvr_probe+0x1b4/0x8e8)
[<c041fa30>] (stmmac_dvr_probe) from [<c04298c8>] (socfpga_dwmac_probe+0x1b8/0x28c)
[<c04298c8>] (socfpga_dwmac_probe) from [<c03d6ffc>] (platform_drv_probe+0x4c/0xb0)
[<c03d6ffc>] (platform_drv_probe) from [<c03d54ec>] (driver_probe_device+0x224/0x2bc)
[<c03d54ec>] (driver_probe_device) from [<c03d5630>] (__driver_attach+0xac/0xb0)
[<c03d5630>] (__driver_attach) from [<c03d382c>] (bus_for_each_dev+0x6c/0xa0)
[<c03d382c>] (bus_for_each_dev) from [<c03d4ad4>] (bus_add_driver+0x1a4/0x21c)
[<c03d4ad4>] (bus_add_driver) from [<c03d60ac>] (driver_register+0x78/0xf8)
[<c03d60ac>] (driver_register) from [<c0101760>] (do_one_initcall+0x40/0x170)
[<c0101760>] (do_one_initcall) from [<c0800e38>] (kernel_init_freeable+0x1dc/0x27c)
[<c0800e38>] (kernel_init_freeable) from [<c05d1bd4>] (kernel_init+0x8/0x114)
[<c05d1bd4>] (kernel_init) from [<c01076f8>] (ret_from_fork+0x14/0x3c)
---[ end trace 059d2fbe87608fa9 ]---
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Matthew Gerlach <mgerlach@opensource.altera.com> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: David S. Miller <davem@davemloft.net> Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 24 Apr 2016 18:32:05 +0000 (14:32 -0400)]
Merge branch 'macsec-fixes'
Sabrina Dubroca says:
====================
macsec: a few fixes
Some small fixes for the macsec driver:
- possible NULL pointer dereferences
- netlink dumps fixes: RTNL locking, consistent dumps
- a reference counting bug
- wrong name for uapi constant
- a few memory leaks
Patches 1 to 5 are the same as in v1, patches 6 to 9 are new.
Patch 6 fixes the memleak that Lance spotted in v1.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
macsec_validate_attr should check IFLA_MACSEC_REPLAY_PROTECT (not
IFLA_MACSEC_PROTECT) to verify that the replay protection and replay
window arguments are correct.
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
I accidentally forgot some MACSEC_ prefixes in if_macsec.h.
Fixes: dece8d2b78d1 ("uapi: add MACsec bits") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
macsec: fix memory leaks around rx_handler (un)registration
We leak a struct macsec_rxh_data when we unregister the rx_handler in
macsec_dellink.
We also leak a struct macsec_rxh_data in register_macsec_dev if we fail
to register the rx_handler.
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver") Suggested-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
macsec: fix rx_sa refcounting with decrypt callback
The decrypt callback macsec_decrypt_done needs a reference on the rx_sa
and releases it before returning, but macsec_handle_frame already
put that reference after macsec_decrypt returned NULL.
Set rx_sa to NULL when the decrypt callback runs so that
macsec_handle_frame knows it must not release the reference.
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver") Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 24 Apr 2016 18:23:38 +0000 (14:23 -0400)]
Merge branch 'bridge-mdb-fixes'
Jiri Pirko says:
====================
bridge: mdb: Couple of fixes
Elad says:
This patchset fixes two problems reported by Nikolay Aleksandrov. The first
problem is that the MDB offload flag might be accesed without helding the
multicast_lock.
The second problem is that the switchdev mdb offload is deferred and
the offload bit was marked regardless if the operation succeeded or not.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Elad Raz [Thu, 21 Apr 2016 10:52:45 +0000 (12:52 +0200)]
bridge: mdb: Marking port-group as offloaded
There is a race-condition when updating the mdb offload flag without using
the mulicast_lock. This reverts commit 9e8430f8d60d98 ("bridge: mdb:
Passing the port-group pointer to br_mdb module").
This patch marks offloaded MDB entry as "offload" by changing the port-
group flags and marks it as MDB_PG_FLAGS_OFFLOAD.
When switchdev PORT_MDB succeeded and adds a multicast group, a completion
callback is been invoked "br_mdb_complete". The completion function
locks the multicast_lock and finds the right net_bridge_port_group and
marks it as offloaded.
Fixes: 9e8430f8d60d98 ("bridge: mdb: Passing the port-group pointer to br_mdb module") Reported-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Elad Raz <eladr@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Elad Raz [Thu, 21 Apr 2016 10:52:44 +0000 (12:52 +0200)]
bridge: mdb: Common function for mdb entry translation
There is duplicate code that translates br_mdb_entry to br_ip let's wrap it
in a common function.
Signed-off-by: Elad Raz <eladr@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Elad Raz [Thu, 21 Apr 2016 10:52:43 +0000 (12:52 +0200)]
switchdev: Adding complete operation to deferred switchdev ops
When using switchdev deferred operation (SWITCHDEV_F_DEFER), the operation
is executed in different context and the application doesn't have any way
to get the operation real status.
Adding a completion callback fixes that. This patch adds fields to
switchdev_attr and switchdev_obj "complete_priv" field which is used by
the "complete" callback.
Application can set a complete function which will be called once the
operation executed.
Signed-off-by: Elad Raz <eladr@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
MAINTAINERS: net: add entry for TI Ethernet Switch drivers
Add record for TI Ethernet Switch Driver CPSW/CPDMA/MDIO HW
(am33/am43/am57/dr7/davinci) to ensure that related patches
will go through dedicated linux-omap list.
Also add Mugunthan as maintainer and myself as the reviewer.
Cc: "David S. Miller" <davem@davemloft.net> Cc: Tony Lindgren <tony@atomide.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal fixes from Eduardo Valentin:
"Specifics in this pull request:
- Fixes in mediatek and OF thermal drivers
- Fixes in power_allocator governor
- More fixes of unsigned to int type change in thermal_core.c.
These change have been CI tested using KernelCI bot. \o/"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: fix Mediatek thermal controller build
thermal: consistently use int for trip temp
thermal: fix mtk_thermal build dependency
thermal: minor mtk_thermal.c cleanups
thermal: power_allocator: req_range multiplication should be a 64 bit type
thermal: of: add __init attribute
Merge tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic update from Arnd Bergmann:
"Here is one patch to wire up the preadv/pwritev system calls in the
generic system call table, which is required for all architectures
that were merged in the last few years, including arm64.
Usually these get merged along with the syscall implementation or one
of the architecture trees, but this time that did not happen.
Andre and Christoph both sent a version of this patch, I picked the
one I got first"
* tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
generic syscalls: wire up preadv2 and pwritev2 syscalls
projects / linux-beck.git / log