Janusz Uzycki [Fri, 14 Nov 2014 22:24:33 +0000 (23:24 +0100)]
serial: mxs-auart: fix gpio change detection on interrupt
mxs_auart_modem_status() did't detect gpio's state change
because s->mctrl_prev was modified before by mctrl_gpio_get().
The patch introduces mctrl_temp variable to fix the bug.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Daney [Fri, 14 Nov 2014 14:26:19 +0000 (17:26 +0300)]
serial: 8250_dw: Use 64-bit access for OCTEON.
Although the existing code appears to work on most hardware, the
hardware designers tell us that 8-bit access to the registers is not
guaranteed to be reliable. Also the OCTEON simulation environments
prohibit 8-bit accesses.
For these reasons, we use __raw_readq/__raw_writeq for OCTEON. This
code is protected with #ifdef CONFIG_64BIT so it still builds under
configurations lacking readq/writeq.
We can get rid of the #ifdef __BIG_ENDIAN, as under 64-bit accesses,
OCTEON is byte order invariant.
Fabio Estevam [Wed, 12 Nov 2014 17:55:07 +0000 (15:55 -0200)]
serial: imx: Fix warning when building 'allmodconfig'
When CONFIG_SERIAL_IMX_CONSOLE=n and CONFIG_CONSOLE_POLL=y we get the following
build warning:
drivers/tty/serial/imx.c:306:13: warning: 'imx_port_ucrs_save' defined but not used [-Wunused-function]
drivers/tty/serial/imx.c:315:13: warning: 'imx_port_ucrs_restore' defined but not used [-Wunused-function]
imx_port_ucrs_save/restore are only used under CONFIG_SERIAL_IMX_CONSOLE, so
their definitions should be also be protected only by CONFIG_SERIAL_IMX_CONSOLE.
Jiri Slaby [Wed, 12 Nov 2014 10:55:25 +0000 (11:55 +0100)]
tty: bfin, define inlined structures
struct bfin_serial_port contains structs circ_buf, timer_list, and
work_struct directly (not pointers). This means that these structures
have to be defined completely to be inlined in struct
bfin_serial_port.
So instead of struct declarations, define the structures by including
proper headers. They were pulled in by linux/serial_core.h or others
until now. But experimenting with circ_buf removal from serial_core,
struct circ_buf becomes undefined in bfin_serial:
In file included from arch/blackfin/kernel/debug-mmrs.c:21:0:
arch/blackfin/include/asm/bfin_serial.h:44:18: error: field 'rx_dma_buf' has incomplete type
tty: serial: omap_serial: line is unsigned, don't check < 0
Dan Carpenter reported:
|drivers/tty/serial/8250/8250_omap.c:1025 omap8250_probe()
|warn: unsigned 'up.port.line' is never less than zero.
|1025 if (up.port.line < 0) {
Since of_alias_get_id() and pdev->id can get negative I check for the
error via ret variable.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty: serial: 8250: omap: line is unsigned, don't check < 0
Dan Carpenter reported:
|drivers/tty/serial/8250/8250_omap.c:1025 omap8250_probe()
|warn: unsigned 'up.port.line' is never less than zero.
|1025 if (up.port.line < 0) {
I (wrongly) assumed that line is an int and compiler didn't complain nor
did sparse. Since of_alias_get_id() and pdev->id can get negative I
check for the error via ret variable.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qipan Li [Tue, 11 Nov 2014 12:44:58 +0000 (20:44 +0800)]
serial: sirf: add a new uart type support
in CSR A7DA SoC, uart6 located at BT module and it need multiple clock
sources, so for "sirf,marco-bt-uart" compatible uarts, drivers take 3
clock sources and enable them.
this patch also replaces clk_get by devm_clk_get function and fix DT
binding document in which we missed to fix when we added marco platform
in commit 909102db44f "serial: sirf: add support for Marco chip".
Signed-off-by: Qipan Li <Qipan.Li@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Joe Perches [Mon, 10 Nov 2014 06:46:35 +0000 (22:46 -0800)]
tty: pr_warning->pr_warn and logging neatening
Convert the pr_warning to the more common pr_warn.
Other miscellanea:
o Convert unusual PR_FMT define and uses to pr_fmt
o Remove unnecessary OOM message
o Fix grammar in an error message
o Convert a pr_warning with a KERN_ERR to pr_err
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: jsm: Replace magic value with the proper define
The changed function flushes the tx UART and the '4' corresponds to the
UART_FCR_CLEAR_XMIT value. This commit replaces the magic number with
this define.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The flow of {neo,cls}_param() shows that at this stage the baud rate
has a non-zero value. This fact makes the if clausule obsolete and
acknowledges it's removal.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: jsm: Remove unnecessary parameter from clear_break()
The 'force' parameter to the {cls,neo}_send_break() function has been
removed because it has not been used. The client to this API (the tty
code) always called this function with only one value.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: sh-sci: Change checking for error rate of HSCIF
This changes negative values of error rate to be checked, because these
values are valid as error rate. And this changes in the process of adopting
a value close to 0.
Stephen Boyd [Fri, 14 Nov 2014 18:39:21 +0000 (10:39 -0800)]
tty: serial: msm_serial: Don't require DT aliases
If there isn't a DT alias then of_alias_get_id() will return
-ENODEV. This will cause the msm_serial driver to fail probe,
when we want to keep the previous behavior where we generated a
dynamic line number at probe time. Restore this behavior by
generating a dynamic id if the line number is still negative
after checking for an alias or in the non-DT case looking at the
.id field of the platform device.
Reported-by: Kevin Hilman <khilman@kernel.org> Tested-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move macro definition for vt_get_kmsg_redirect() up with file-scope
function declarations.
Reported-by: Jim Davis <jim.epost@gmail.com> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To quote Olof:
This commit broke a whole lot of tegra boards in last night's
-next here. In particular, I've been looking at
tegra20-seaboard, which now doesn't boot with console any more.
Breaking existing systems is bad.
Reported-by: Olof Johansson <olof@lixom.net> Cc: Lucas Stach <dev@lynxeye.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sun, 9 Nov 2014 22:49:56 +0000 (14:49 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- enable bpf syscall for compat
- cpu_suspend fix when checking the idle state type
- defconfig update
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: defconfig: update defconfig for 3.18
arm64: compat: Enable bpf syscall
arm64: psci: fix cpu_suspend to check idle state type for index
Linus Torvalds [Sun, 9 Nov 2014 22:46:36 +0000 (14:46 -0800)]
Merge tag 'armsoc-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another quiet week:
- a fix to silence edma probe error on non-supported platforms from
Arnd
- a fix to enable the PL clock for Parallella, to make mainline
usable with the SDK.
- a somewhat verbose fix for the PLL clock tree on VF610
- enabling of SD/MMC on one of the VF610-based boards (for testing)
- a fix for i.MX where CONFIG_SPI used to be implicitly enabled and
now needs to be added to the defconfig instead
- another maintainer added for bcm2835: Lee Jones"
* tag 'armsoc-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: zynq: Enable PL clocks for Parallella
dma: edma: move device registration to platform code
ARM: dts: vf610: add SD node to cosmic dts
MAINTAINERS: update bcm2835 entry
ARM: imx: Fix the removal of CONFIG_SPI option
ARM: imx: clk-vf610: define PLL's clock tree
Linus Torvalds [Sun, 9 Nov 2014 22:30:24 +0000 (14:30 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fix from Chris Mason:
"It's a one liner for an error cleanup path that leads to crashes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix kfree on list_head in btrfs_lookup_csums_range error cleanup
Linus Torvalds [Sun, 9 Nov 2014 22:11:58 +0000 (14:11 -0800)]
Merge tag 'driver-core-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are 3 tiny fixes for 3.18-rc4.
One fixes up a long-stading race condition in the driver core for
removing directories in /sys/devices/virtual/ and the other 2 fix up
the wording of a new Kconfig option that was added in 3.18-rc1"
* tag 'driver-core-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
tiny: reverse logic for DISABLE_DEV_COREDUMP
sysfs: driver core: Fix glue dir race condition by gdp_mutex
Linus Torvalds [Sun, 9 Nov 2014 22:11:07 +0000 (14:11 -0800)]
Merge tag 'staging-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some staging/iio fixes for 3.18-rc4.
Nothing major, just a few bugfixes of things that have been reported"
* tag 'staging-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging:iio:ade7758: Remove "raw" from channel name
staging:iio:ade7758: Fix check if channels are enabled in prenable
staging:iio:ade7758: Fix NULL pointer deref when enabling buffer
iio: as3935: allocate correct iio_device size
io: accel: kxcjk-1013: Fix iio_event_spec direction
iio: tsl4531: Fix compiler error when CONFIG_PM_OPS is not defined
iio: adc: mxs-lradc: Disable the clock on probe failure
iio: st_sensors: Fix buffer copy
staging:iio:ad5933: Drop "raw" from channel names
staging:iio:ad5933: Fix NULL pointer deref when enabling buffer
Linus Torvalds [Sun, 9 Nov 2014 22:07:30 +0000 (14:07 -0800)]
Merge tag 'tty-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tiny serial/tty fixes for 3.18-rc4 that resolve some
reported issues"
* tag 'tty-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix pty master poll() after slave closes v2
serial: of-serial: fix uninitialized kmalloc variable
tty/vt: don't set font mappings on vc not supporting this
tty: serial: 8250_mtk: Fix quot calculation
tty: Prevent "read/write wait queue active!" log flooding
tty: Fix high cpu load if tty is unreleaseable
serial: Fix divide-by-zero fault in uart_get_divisor()
Linus Torvalds [Sun, 9 Nov 2014 22:05:53 +0000 (14:05 -0800)]
Merge tag 'usb-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 3.18-rc4.
Just a bunch of little fixes resolving reported issues and new device
ids for existing drivers. Full details are in the shortlog"
* tag 'usb-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
USB: Update default usb-storage delay_use value in kernel-parameters.txt
USB: cdc-acm: add quirk for control-line state requests
phy: omap-usb2: Enable runtime PM of omap-usb2 phy properly
USB: storage: Fix timeout in usb_stor_euscsi_init() and usb_stor_huawei_e220_init()
USB: cdc-acm: only raise DTR on transitions from B0
Revert "storage: Replace magic number with define in usb_stor_euscsi_init()"
usb: core: notify disconnection when core detects disconnect
usb: core: need to call usb_phy_notify_connect after device setup
uas: Add US_FL_NO_ATA_1X quirk for 2 more Seagate models
xhci: no switching back on non-ULT Haswell
USB: quirks: enable device-qualifier quirk for yet another Elan touchscreen
USB: quirks: enable device-qualifier quirk for another Elan touchscreen
MAINTAINERS: Remove duplicate entry for usbip driver
usb: storage: fix build warnings !CONFIG_PM
usb: Remove references to non-existent PLAT_S5P symbol
uas: Add NO_ATA_1X for VIA VL711 devices
xhci: Disable streams on Asmedia 1042 xhci controllers
USB: HWA: fix a warning message
uas: Add US_FL_NO_ATA_1X quirk for 1 more Seagate model
usb-storage: handle a skipped data phase
...
Andreas Färber [Thu, 6 Nov 2014 17:22:10 +0000 (18:22 +0100)]
ARM: dts: zynq: Enable PL clocks for Parallella
The Parallella board comes with a U-Boot bootloader that loads one of
two predefined FPGA bitstreams before booting the kernel. Both define an
AXI interface to the on-board Epiphany processor.
Enable clocks FCLK0..FCLK3 for the Programmable Logic by default.
Otherwise accessing, e.g., the ESYSRESET register freezes the board,
as seen with the Epiphany SDK tools e-reset and e-hw-rev, using /dev/mem.
Cc: <stable@vger.kernel.org> # 3.17.x Signed-off-by: Andreas Färber <afaerber@suse.de> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Sat, 8 Nov 2014 17:32:29 +0000 (09:32 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c bugfixes from Wolfram Sang:
"One bigger cleanup (FSF address removal) and two bugfixes for I2C"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: Dispose OF IRQ mapping at client removal time
i2c: at91: don't account as iowait
i2c: remove FSF address
Pull media fixes from Mauro Carvalho Chehab:
"For:
- some regression fixes at the Remote Controller core and imon driver
- a build fix for certain randconfigs with ir-hix5hd2
- don't feed power to satellite system at ds3000 driver init
It also contains some fixes for drivers added for Kernel 3.18:
- some fixes at the new ISDB-S driver, and the corresponding bits to
fix some descriptors for this Japanese TV standard at the DVB core
- two warning cleanups for sp2 driver if PM is disabled
- change the default mode for the new vivid driver"
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] sp2: sp2_init() can be static
[media] dvb:tc90522: fix always-false expression
[media] dvb-core: set default properties of ISDB-S
[media] dvb:tc90522: fix stats report
[media] vivid: default to single planar device instances
[media] imon: fix other RC type protocol support
[media] ir-hix5hd2 fix build warning
[media] ds3000: fix LNB supply voltage on Tevii S480 on initialization
[media] rc5-decoder: BZ#85721: Fix RC5-SZ decoding
[media] rc-core: fix protocol_change regression in ir_raw_event_register
Linus Torvalds [Sat, 8 Nov 2014 02:08:02 +0000 (18:08 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"This weeks' round of MIPS bug fixes for 3.18:
- wire up the bpf syscall
- fix TLB dump output for R3000 class TLBs
- fix strnlen_user return value if no NUL character was found.
- fix build with binutils 2.24.51+. While there is no binutils 2.25
release yet, toolchains derived from binutils 2.24.51+ are already
in common use.
- the Octeon GPIO code forgot to offline GPIO IRQs.
- fix build error for XLP.
- fix possible BUG assertion with EVA for CMA"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix build with binutils 2.24.51+
MIPS: R3000: Fix debug output for Virtual page number
MIPS: Fix strnlen_user() return value in case of overlong strings.
MIPS: CMA: Do not reserve memory if not required
MIPS: Wire up bpf syscall.
MIPS/Xlp: Remove the dead function destroy_irq() to fix build error
MIPS: Octeon: Make Octeon GPIO IRQ chip CPU hotplug-aware
Linus Torvalds [Fri, 7 Nov 2014 22:08:13 +0000 (14:08 -0800)]
Merge tag 'xfs-for-linus-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"This update fixes a warning in the new pagecache_isize_extended() and
updates some related comments, another fix for zero-range
misbehaviour, and an unforntuately large set of fixes for regressions
in the bulkstat code.
The bulkstat fixes are large but necessary. I wouldn't normally push
such a rework for a -rcX update, but right now xfsdump can silently
create incomplete dumps on 3.17 and it's possible that even xfsrestore
won't notice that the dumps were incomplete. Hence we need to get
this update into 3.17-stable kernels ASAP.
In more detail, the refactoring work I committed in 3.17 has exposed a
major hole in our QA coverage. With both xfsdump (the major user of
bulkstat) and xfsrestore silently ignoring missing files in the
dump/restore process, incomplete dumps were going unnoticed if they
were being triggered. Many of the dump/restore filesets were so small
that they didn't evenhave a chance of triggering the loop iteration
bugs we introduced in 3.17, so we didn't exercise the code
sufficiently, either.
We have already taken steps to improve QA coverage in xfstests to
avoid this happening again, and I've done a lot of manual verification
of dump/restore on very large data sets (tens of millions of inodes)
of the past week to verify this patch set results in bulkstat behaving
the same way as it does on 3.16.
Unfortunately, the fixes are not exactly simple - in tracking down the
problem historic API warts were discovered (e.g xfsdump has been
working around a 20 year old bug in the bulkstat API for the past 10
years) and so that complicated the process of diagnosing and fixing
the problems. i.e. we had to fix bugs in the code as well as
discover and re-introduce the userspace visible API bugs that we
unwittingly "fixed" in 3.17 that xfsdump relied on to work correctly.
Summary:
- incorrect warnings about i_mutex locking in pagecache_isize_extended()
and updates comments to match expected locking
- another zero-range bug fix for stray file size updates
- a bunch of fixes for regression in the bulkstat code introduced in
3.17"
* tag 'xfs-for-linus-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: track bulkstat progress by agino
xfs: bulkstat error handling is broken
xfs: bulkstat main loop logic is a mess
xfs: bulkstat chunk-formatter has issues
xfs: bulkstat chunk formatting cursor is broken
xfs: bulkstat btree walk doesn't terminate
mm: Fix comment before truncate_setsize()
xfs: rework zero range to prevent invalid i_size updates
mm: Remove false WARN_ON from pagecache_isize_extended()
xfs: Check error during inode btree iteration in xfs_bulkstat()
xfs: bulkstat doesn't release AGI buffer on error
Linus Torvalds [Fri, 7 Nov 2014 19:55:47 +0000 (11:55 -0800)]
Merge tag 'regulator-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"More changes than I'd like here, most of them for a single bug
repeated in a bunch of drivers with data not being initialized
correctly, plus a fix to lower the severity of a warning introduced in
the last merge window which can legitimately go off so we don't want
to alarm users excessively"
* tag 'regulator-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: s2mpa01: zero-initialize regulator match table array
regulator: max8660: zero-initialize regulator match table array
regulator: max77802: zero-initialize regulator match table
regulator: max77686: zero-initialize regulator match table
regulator: max1586: zero-initialize regulator match table array
regulator: max77693: Fix use of uninitialized regulator config
regulator: of: Lower the severity of the error with no container
Linus Torvalds [Fri, 7 Nov 2014 19:54:44 +0000 (11:54 -0800)]
Merge tag 'spi-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi bugfixes from Mark Brown:
"A couple of small driver fixes for v3.18, both quite problematic if
you hit a use case that's affected"
* tag 'spi-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: pxa2xx: toggle clocks on suspend if not disabled by runtime PM
spi: fsl-dspi: Fix CTAR selection
Johannes Berg [Thu, 30 Oct 2014 09:00:35 +0000 (10:00 +0100)]
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
The ENABLE_DEV_COREDUMP option is misleading as it implies that
it gets the framework enabled, this isn't true it just allows it
to get enabled if a driver needs it.
Rename it to ALLOW_DEV_COREDUMP to better capture its semantics.
Aristeu Rozanski [Thu, 16 Oct 2014 15:49:49 +0000 (11:49 -0400)]
tiny: reverse logic for DISABLE_DEV_COREDUMP
It's desirable for allnconfig and tinyconfig targets to result in the
least amount of code possible. DISABLE_DEV_COREDUMP exists as a way to
switch off DEV_COREDUMP regardless if any drivers select
WANT_DEV_COREDUMP.
This patch renames the option to ENABLE_DEV_COREDUMP and setting it to
'n' (as in allnconfig or tinyconfig) will effectively disable device
coredump.
Mark Knibbs [Tue, 4 Nov 2014 13:00:15 +0000 (13:00 +0000)]
USB: Update default usb-storage delay_use value in kernel-parameters.txt
Back in 2010 the default usb-storage delay_use time was reduced from 5 to 1
second (commit a4a47bc03fe520e95e0c4212bf97c86545fb14f9), but
kernel-parameters.txt wasn't updated to reflect that.
Signed-off-by: Mark Knibbs <markk@clara.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrew Jackson [Fri, 7 Nov 2014 14:14:47 +0000 (14:14 +0000)]
serial: pl011: Don't enable RX DMA if residue processing not supported
If the DMA engine doesn't support residue processing then the RX DMA
handling won't work terribly well if polling is enabled. So, disable
RX DMA if residue handling isn't available.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrew Jackson [Fri, 7 Nov 2014 14:14:39 +0000 (14:14 +0000)]
serial: pl011: Avoid assumptions about buffer size when refilling TX DMA
The existing code assumed that PL011_DMA_BUFFER_SIZE == UART_XMIT_SIZE,
which may not always be the case. This allows for these two being
different sizes and not copying too much data.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no real value in displaying "serial: Freescale lpuart driver" in every
boot.
The uart_register_driver() can fail and even so the "serial: Freescale lpuart
driver" will be displayed, which is not really helpful.
This is particularly annoying when booting multi_v7_defconfig kernel on a SoC
that is not a Vybrid/Layerscape and even though this message gets displayed.
Yijing Wang [Fri, 7 Nov 2014 04:05:49 +0000 (12:05 +0800)]
sysfs: driver core: Fix glue dir race condition by gdp_mutex
There is a race condition when removing glue directory.
It can be reproduced in following test:
path 1: Add first child device
device_add()
get_device_parent()
/*find parent from glue_dirs.list*/
list_for_each_entry(k, &dev->class->p->glue_dirs.list, entry)
if (k->parent == parent_kobj) {
kobj = kobject_get(k);
break;
}
....
class_dir_create_and_add()
path2: Remove last child device under glue dir
device_del()
cleanup_device_parent()
cleanup_glue_dir()
kobject_put(glue_dir);
If path2 has been called cleanup_glue_dir(), but not
call kobject_put(glue_dir), the glue dir is still
in parent's kset list. Meanwhile, path1 find the glue
dir from the glue_dirs.list. Path2 may release glue dir
before path1 call kobject_get(). So kernel will report
the warning and bug_on.
This is a "classic" problem we have of a kref in a list
that can be found while the last instance could be removed
at the same time.
This patch reuse gdp_mutex to fix this race condition.
The following calltrace is captured in kernel 3.4, but
the latest kernel still has this bug.
Manuel Lauss [Fri, 7 Nov 2014 13:13:54 +0000 (14:13 +0100)]
MIPS: Fix build with binutils 2.24.51+
Starting with version 2.24.51.20140728 MIPS binutils complain loudly
about mixing soft-float and hard-float object files, leading to this
build failure since GCC is invoked with "-msoft-float" on MIPS:
To fix this, we detect if GAS is new enough to support "-msoft-float" command
option, and if it does, we can let GCC pass it to GAS; but then we also need
to sprinkle the files which make use of floating point registers with the
necessary ".set hardfloat" directives.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Cc: Linux-MIPS <linux-mips@linux-mips.org> Cc: Matthew Fortune <Matthew.Fortune@imgtec.com> Cc: Markos Chandras <Markos.Chandras@imgtec.com> Cc: Maciej W. Rozycki <macro@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8355/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers: serial: jsm: Enable support for Digi Classic adapters
This commit enables support for the Digi Classic adapters line in the
jsm driver. This means changes in:
- device probing code
- device cleanup code
- driver description (Kconfig)
The init/cleanup code is based on the staging/dgnc driver.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers: serial: jsm: Add the Classic board implementation
This commit adds the Digi Classic board implementation to the
staging/jsm driver.
The code here is taken from the staging/dgnc driver and modified to
match the serial/jsm state. This work is mostly based on the changes
that has been done to the code handling the Digi Neo cards with the
inspiration coming from the diff between staging/dgnc and serial/jsm
as well as the LKML history for the jsm_neo.c
The code compiles now and has no sparse and checkpatch errors or
warnings.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Frans Klaver [Thu, 6 Nov 2014 20:10:17 +0000 (21:10 +0100)]
serial: 8250_core: actually limit char reads to max_count
In serial8250_rx_chars(), max_count is set to 256. Due to the
post-decrement operator used in the while() condition, the maximum
number of iterations actually 257. This is not a problem, but it is
mildly surprising if you're debugging. Use pre-decrement instead.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Slaby [Thu, 6 Nov 2014 15:56:33 +0000 (16:56 +0100)]
tty: warn on deprecated serial flags
When somebody calls TIOCSSERIAL ioctl with serial flags to set one of
* ASYNC_SESSION_LOCKOUT
* ASYNC_PGRP_LOCKOUT
* ASYNC_CALLOUT_NOHUP
* ASYNC_AUTOPROBE
nothing happens. We actually ignore the flags for over a decade at
least (I checked 2.6.0).
So start yelling at users who use those flags, that they shouldn't.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Peter Hurley <peter@hurleysoftware.com> Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following drivers: 8250_core, atmel_serial, max310x, mcf, omap-serial
and sci16is7xx implement code to handle RS485 ioctls.
In order to avoid code duplication, we implement a simple ioctl handler
on the serial_core layer.
This handler can be used by all the other drivers instead of duplicating
code.
Until this is the only RS485 ioctl handler, it will try first the
rs485_config callback and if it is not present it will call the driver
specific ioctl.
Peter Hurley [Wed, 5 Nov 2014 18:11:45 +0000 (13:11 -0500)]
serial: Test/disable MSIs if switching from N_PPS
Switching to the N_PPS line discipline may require enabling
modem status interrupts; conversely switching from N_PPS may
require disabling modem status interrupts.
Affected drivers:
8250
amba-pl010
atmel
Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Russell King <linux@arm.linux.org.uk> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Wed, 5 Nov 2014 18:11:43 +0000 (13:11 -0500)]
serial: core: Pass termios to set_ldisc() notifications
UART drivers which enable modem status interrupts when switching
to N_PPS line discipline need to determine if modem status
interrupts should be disabled when switching from N_PPS.
Specifically, the set_ldisc() notification needs to evaluate
UART_ENABLE_MS() which requires termios->c_cflag.
Convert in-tree UART drivers to new interface.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Wed, 5 Nov 2014 18:11:42 +0000 (13:11 -0500)]
serial: core: Claim port mutex for set_ldisc()
Three UART drivers (8250, atmel & amba-pl010) enable modem status
interrupts if the line discipline is changed to N_PPS. However,
the uart port flags may only be safely modified while holding the
port mutex.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Wed, 5 Nov 2014 18:11:41 +0000 (13:11 -0500)]
tty: Allow safe access to termios for set_ldisc() handlers
Allow a tty driver to safely access termios settings while handling
the set_ldisc() notification. UART drivers use the set_ldisc()
notification to check if the N_PPS line discipline is being enabled;
if so, modem status interrupts may also need to be enabled. Conversely,
modem status interrupts may need to be disabled if switching away
from the N_PPS line discipline.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Wed, 5 Nov 2014 17:40:05 +0000 (12:40 -0500)]
tty: Flush tty buffers after hardware shutdown
The line discipline buffer and the tty buffers must be flushed again
after hardware shutdown; otherwise, a brief window exists between the
ldisc flush in tty_port_close_start() and the subsequent
tty_port_shutdown(), during which more data could be received into the
tty buffers. A racing open might then be able to receive data from the
previous session.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Julien CHAUVEAU [Tue, 4 Nov 2014 10:45:55 +0000 (11:45 +0100)]
serial: 8250_dw: get index of serial line from DT aliases
Get index of serial line from device tree using function of_alias_get_id().
If no alias is found, the 8250 core takes care of incrementing the line number.
Lucas Stach [Mon, 3 Nov 2014 22:16:54 +0000 (23:16 +0100)]
serial: of-serial: fetch line number from DT
The general agreed way to specify a fixed line number
for a serial console is to provide a "serial" alias
in the devicetree. Start parsing this property in
of_serial.
Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several init/setup functions passed the PCI BAR resource start address
to ioremap_nocache() via an unsigned long. This caused address truncation
for a 32-bit device mapped above 4 GiB (i.e. the CPU interacts with the
device via a translated address), which resulted in a kernel panic.
This patch replaces all of the instances of intermediate variable use
with pci_ioremap_bar() to ensure the full resource_size_t start address
is used and that ioremap_nocache() is still called.
The kernel panic (Exar XR17V358 PCIe device on a Freescale P2020 SBC):
In mtk8250_set_termios function, calculating quot value can not be zero,
otherwise, using DIV_ROUND_CLOSEST(port->uartclk, quot * baud) will fail due to
divisor is zero.
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't really need to perform the ioremap "on demand" so it's simpler
just to do it from the probe function. This also lets us eliminate the
UART_REG_SIZE constant and rely on the resource information passed in
from the DT or platform code.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kevin Cernekee [Tue, 21 Oct 2014 22:23:02 +0000 (15:23 -0700)]
tty: serial: bcm63xx: Enable DT earlycon support
This enables early console output if there is a chosen/stdout-path
property referencing a UART node with the "brcm,bcm6345-uart" compatible
string. The bootloader sets up the pinmux and baud/parity/etc.
Tested on bcm3384 (MIPS, DT).
Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kevin Cernekee [Tue, 21 Oct 2014 22:22:58 +0000 (15:22 -0700)]
tty: serial: bcm63xx: Add support for unnamed clock outputs from DT
The original non-DT bcm63xx clk code ignores the struct device argument
and looks up a global clock name. DT platforms, by contrast, often just
use a phandle to reference a clock node with no "clock-output-names"
property. Modify the UART driver to support both schemes.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log