Mark Brown [Sat, 3 Dec 2011 10:49:26 +0000 (19:49 +0900)]
ARM: S3C64XX: Power gate unused domains
The S3C64xx CPUs have power gating support with a series of software
controllable power domains in the SoC. To take full advantage of these
we should implement runtime PM support but since several of the IP blocks
have no in tree drivers (and at this point aren't likely to acquire such
drivers) we can get some benefit from the hardware much more easily if
we just turn those blocks off unconditionally. This will cut down on the
leakage these domains generate without interfering with active usage.
Do this for:
- Domain G: 3D acceleration
- Domain V: MFC
- Domain I: JPEG and camera interface
- Domain P: 2D acceleration, TV encoder and scaler
This is easy to reverse if any of these devices do acquire drivers in the
future or as part of out of tree patches for them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Mark Brown [Fri, 2 Dec 2011 05:32:32 +0000 (14:32 +0900)]
ARM: S3C64XX: Hook up Littlemill audio card on Cragganmore
The Littlemill audio card is an adaptor card which can take any 6220-EV1
CODEC daughtercard. Provide standard support for the use of WM8994 class
devices on the Littlemill card, configuring the MFD for WM8958 usage as
this part is a superset of all others and the driver will use runtime
detection to identify the actually fitted part given the configuration for
the superset.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[kgene.kim@samsung.com: fix up conflict] Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Mark Brown [Fri, 2 Dec 2011 05:29:08 +0000 (14:29 +0900)]
ARM: S3C64XX: Improve logging of unknown Cragganmore module types
As our ID table is populated with hexidecimal values it makes sense to log
unknown module IDs in hexidecimal. It's also helpful to display board
revisions as 1 based rather than 0 based as that's the numbering system
used for the hardware (and what we do when announcing known modules).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Mark Brown [Fri, 2 Dec 2011 05:29:07 +0000 (14:29 +0900)]
ARM: S3C64XX: Use software initiated powerdown for Cragganmore
Since the two PMICs are independent we initiate a shutdown on each.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[kgene.kim@samsung.com: fix up conflict] Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ARM: SAMSUNG: Remove SPI bus clocks from platform data
SPI bus clocks can be avoided passing through platform
data as spi driver is getting the bus clock using the
generic clock connection id registered via clkdev.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch modifies the driver to stop depending on the
clock names being passed from platform and switch over
to lookup clocks generic names using clkdev
Signed-off-by: Padmavathi Venna <padma.v@samsung.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
mmc: sdhci-s3c: Use generic clock names for sdhci bus clock options
This patch modifies the driver to stop depending on the clock names
being passed from the platform and switch over to bus clock lookup
using generic clock names.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Chris Ball <cjb@laptop.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Wed, 2 Nov 2011 10:31:15 +0000 (19:31 +0900)]
ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN
Add initial dts file for EXYNOS4210 SoC. This dts file describes
the SoC specific devices and properties. Along with this, add dts
file for Samsung's SMDKV310 board and Insignal's ORIGEN board which
uses the EXYNOS4210 dts file and extends it to describe the board
specific properties.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Sun, 6 Nov 2011 16:24:27 +0000 (21:54 +0530)]
ARM: EXYNOS: Add Exynos4 device tree enabled board file
Add a new EXYNOS4 compatible device tree enabled board file. Boards
based on the EXYNOS4 family of SoC's can use this as the machine/board
file. When using this machine fike, a corresponding device tree blob
which describes the board's properties should be supplied at boot time
to the kernel.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Mon, 24 Oct 2011 12:49:04 +0000 (14:49 +0200)]
rtc: rtc-s3c: Add device tree support
Add device tree based discovery support for Samsung's rtc controller.
Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Wed, 2 Nov 2011 10:37:22 +0000 (19:37 +0900)]
input: samsung-keypad: Add device tree support
Add device tree based discovery support for Samsung's keypad controller.
Cc: Joonyoung Shim <jy0922.shim@samsung.com> Cc: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Mark Brown [Thu, 3 Nov 2011 07:15:38 +0000 (16:15 +0900)]
ARM: SAMSUNG: Fix GPIO space reservation for S3C64xx platforms
The conversion to use SAMSUNG_GPIO_EXTRA rather than S3C24XX_GPIO_EXTRA
broke a number of S3C64xx boards which had been using the symbols provided
to reserve a range of GPIOs for board specific use. Fix this by adding
equivalent symbols for the new shared driver and updating the relevant
boards to use the new symbols.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Mark Brown [Thu, 3 Nov 2011 07:15:37 +0000 (16:15 +0900)]
ARM: S3C64XX: Update for conversion to SAMSUNG_GPIO_EXTRA
The conversion of the S3C64XX GPIOs to the generic Samsung GPIOs mean that
rather than using the previous S3C24XX_GPIO_EXTRA configuration the driver
now uses SAMSUNG_GPIO_EXTRA.
Since SAMSUNG_GPIO_EXTRA requires the arch to include the extra space in
ARCH_NR_GPIOs add it on to BOARD_NR_GPIOs (in case boards are relying on
the existing reservation).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Mon, 24 Oct 2011 09:45:14 +0000 (11:45 +0200)]
ARM: S5PV210: Modify platform data for pl330 driver
With the 'struct dma_pl330_peri' removed, the platfrom data for dma
driver can be simplified to a simple list of peripheral request ids.
Cc: Jassi Brar <jassisinghbrar@gmail.com> Acked-by: Boojin Kim <boojin.kim@samsung.com> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Mon, 24 Oct 2011 09:45:08 +0000 (11:45 +0200)]
ARM: S5PC100: Modify platform data for pl330 driver
With the 'struct dma_pl330_peri' removed, the platfrom data for dma
driver can be simplified to a simple list of peripheral request ids.
Cc: Jassi Brar <jassisinghbrar@gmail.com> Acked-by: Boojin Kim <boojin.kim@samsung.com> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Mon, 24 Oct 2011 09:45:01 +0000 (11:45 +0200)]
ARM: S5P64x0: Modify platform data for pl330 driver
With the 'struct dma_pl330_peri' removed, the platfrom data for dma
driver can be simplified to a simple list of peripheral request ids.
Cc: Jassi Brar <jassisinghbrar@gmail.com> Cc: Boojin Kim <boojin.kim@samsung.com> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Mon, 24 Oct 2011 12:01:03 +0000 (14:01 +0200)]
ARM: EXYNOS: Add a alias for pdma clocks
PDMA controllers when instantiated from device tree are registered using
amba_device_register(). The registration process enables clock to the
controllers to read the peripheral id of the PDMA amba device.
In case of Exynos4, the clocks to the PDMA controllers are named as 'dma'
but amba_device_register() looks up the clock using the name 'apb_pclk'.
Hence, alias clocks with name 'apb_pclk' clock are created for clocks
with name 'dma'.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Mon, 24 Oct 2011 11:57:43 +0000 (13:57 +0200)]
ARM: EXYNOS: Limit usage of pl330 device instance to non-dt build
The pl330 device instances and associated platform data is required only
for non-device-tree builds. With device tree enabled, the data about the
platform is obtained from the device tree. For images that include both
dt and non-dt platforms, an addditional check is added to ensure that
static amba device registrations is applicable to only non-dt platforms.
Cc: Kukjin Kim <kgene.kim@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Mon, 24 Oct 2011 09:43:38 +0000 (11:43 +0200)]
ARM: SAMSUNG: Add device tree support for pl330 dma engine wrappers
A new dma request id 'DMACH_DT_PROP' is introduced for client drivers
requesting a dma channel. This request indicates that a device tree
node property represting the dma channel is available in
'struct samsung_dma_info'. The dma channel request wrapper uses the
node property value as the value for the filter parameter.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Mon, 24 Oct 2011 09:43:31 +0000 (11:43 +0200)]
DMA: PL330: Add device tree support
For PL330 dma controllers instantiated from device tree, the channel
lookup is based on phandle of the dma controller and dma request id
specified by the client node. During probe, the private data of each
channel of the controller is set to point to the device node of the
dma controller. The 'chan_id' of the each channel is used as the
dma request id.
Client driver requesting dma channels specify the phandle of the
dma controller and the request id. The pl330 filter function
converts the phandle to the device node pointer and matches that
with channel's private data. If a match is found, the request id
from the client node and the 'chan_id' of the channel is matched.
A channel is found if both the values match.
Acked-by: Jassi Brar <jassisinghbrar@gmail.com> Acked-by: Boojin Kim <boojin.kim@samsung.com> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Reviewed-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Mon, 24 Oct 2011 09:43:22 +0000 (11:43 +0200)]
ARM: EXYNOS: Modify platform data for pl330 driver
With the 'struct dma_pl330_peri' removed, the platfrom data for dma
driver can be simplified to a simple list of peripheral request ids.
Cc: Jassi Brar <jassisinghbrar@gmail.com> Acked-by: Boojin Kim <boojin.kim@samsung.com> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Mon, 24 Oct 2011 09:43:11 +0000 (11:43 +0200)]
DMA: PL330: Infer transfer direction from transfer request instead of platform data
The transfer direction for a channel can be inferred from the transfer
request and the need for specifying transfer direction in platfrom data
can be eliminated. So the structure definition 'struct dma_pl330_peri'
is no longer required.
The channel's private data is set to point to a channel id specified in
the platform data (instead of an instance of type 'struct dma_pl330_peri').
The filter function is correspondingly modified to match the channel id.
With the 'struct dma_pl330_peri' removed from platform data, the dma
controller transfer capabilities cannot be inferred any more. Hence,
the dma controller capabilities is specified using platform data.
Acked-by: Jassi Brar <jassisinghbrar@gmail.com> Acked-by: Boojin Kim <boojin.kim@samsung.com> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Mon, 24 Oct 2011 09:43:02 +0000 (11:43 +0200)]
DMA: PL330: move filter function into driver
The dma channel selection filter function is moved from plat-samsung
into the pl330 driver. In additon to that, a check is added in the
filter function to ensure that the channel on which the filter has
been invoked is pl330 channel instance (and avoid any incorrect
access of chan->private in a system with multiple types of DMA
drivers).
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Jassi Brar <jassisinghbrar@gmail.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Mark Brown [Tue, 8 Nov 2011 08:00:14 +0000 (17:00 +0900)]
serial: samsung: Fix build for non-Exynos4210 devices
exynos4120_serial_drv_data is only defined when building with support
for Exynos4210 so use the already provided define to ensure that we
don't reference it when building for other SoCs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[kgene.kim@samsung.com: Fixed build warning] Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Sun, 6 Nov 2011 16:40:44 +0000 (22:10 +0530)]
serial: samsung: add device tree support
Add device tree based discovery support for Samsung's uart controller.
Cc: Ben Dooks <ben-linux@fluff.org> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Wed, 2 Nov 2011 10:23:25 +0000 (19:23 +0900)]
serial: samsung: merge probe() function from all SoC specific extensions
With reset port, set clock and get clock functions in SoC specific extentions
being removed, only the driver probe is left over in these extensions. The
probe function itself can be merged into one and moved into the samsung common
serial driver. With driver probe also moved, all the SoC specific extentions
are no longer required and they are deleted.
Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Mon, 24 Oct 2011 09:48:21 +0000 (11:48 +0200)]
serial: samsung: merge all SoC specific port reset functions
The port reset function in each of the platform specific extension performs
the same operations and hence all the reset port functions can be merged into
one and moved into the common samsung uart driver. The SoC specific port reset
functions are removed from SoC extensions.
Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Mon, 24 Oct 2011 10:08:42 +0000 (12:08 +0200)]
ARM: SAMSUNG: register uart clocks to clock lookup list
Samsung uart driver lookups the clock using the connection id 'clk_uart_baud'.
The uart clocks for all Samsung platforms are reorganized to register them
with the lookup name as required by the uart driver.
Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Mon, 24 Oct 2011 09:47:57 +0000 (11:47 +0200)]
serial: samsung: remove all uses of get_clksrc and set_clksrc
With clkdev based clock lookup support, the clock set and get operation
using clock names communicated between the samsung uart driver and the
SoC specific extension can be removed.
In addition to that, for each platform specific extension, add the
default clock selection, number of clock options for uart baud generator,
clock selection bit mask and shift values which is required by the
clkdev support in samsung uart driver.
The default clock selection value 'def_clk_sel' specifies the default clock
to be used as the source clock for baud rate generator in case the platform
code does not specify the same.
Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Mon, 24 Oct 2011 09:47:51 +0000 (11:47 +0200)]
ARM: SAMSUNG: remove struct 's3c24xx_uart_clksrc' and all uses of it
With clkdev based clock lookup added to samsung serial driver, the use
of 'struct s3c24xx_uart_clksrc' to supply clock names in platform
data is removed from all the Samsung platform code.
Cc: Ben Dooks <ben-linux@fluff.org> Cc: Ramax Lo <ramaxlo@gmail.com> Cc: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Mon, 24 Oct 2011 09:47:46 +0000 (11:47 +0200)]
serial: samsung: switch to clkdev based clock lookup
Instead of using clock names supplied in platform data, use a generic
clock name 'clk_uart_baud' to look up clocks. The platform code should
register clocks with the name 'clk_uart_baud' which can be used by the
baud rate generator. The clock lookup and selection of the best clock
as baud rate clock is reworked.
Platform code can specify the clocks that can be used as source for the
baud clock (as supported previously by passing names of clocks). A new
member is added to the platform data 'clk_sel' which holds a bit-field
value with each bit representing a baud source clock. If a bit at any
bit position is set, that clock is looked up to participate in the
selection of the baud clock source.
Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Mon, 24 Oct 2011 09:47:40 +0000 (11:47 +0200)]
ARM: S3C2440: move handling of fclk/n clock to platform code
s3c2440 uses fclk/n (fclk divided by n) clock as one of the possible clocks used
to generate the baud rate clock. The divider 'n' in this case can be logically
represented outside of the uart controller.
This patch creates a new clock by name "fclk_n" for s3c2440 based platforms to
represent the fclk/n clock in the platform code. This clock provides a get_rate
callback that checks the UCON0/1/2 registers to determine the clock rate. The
samsung uart driver would receive the "fclk_n" clock name as one of the possible
baud rate clock options and the driver need not determine clock rate of fclk/n.
Cc: Ben Dooks <ben-linux@fluff.org> Cc: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Mon, 24 Oct 2011 09:47:25 +0000 (11:47 +0200)]
serial: samsung: Keep a copy of the location of platform data in driver's private data
Add a pointer to the location of the platform data in the driver's private
data. When instantiated using device tree, pdev->dev->platform_data does not
necessarily point to a valid instance of platform data. The platform data
pointer in the driver's private data could be set to pdev->dev->platform_data
or platform data instance created from device tree.
Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Sun, 6 Nov 2011 19:32:21 +0000 (01:02 +0530)]
gpio/samsung: Add device tree support for EXYNOS4
As gpio chips get registered, a device tree node which represents the
gpio chip is searched and attached to it. A translate function is also
provided to convert the gpio specifier into actual platform settings
for pin function selection, pull up/down and driver strength settings.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Grant Likely <grant.likely@secretlab.ca>
[kgene.kim@samsung.com: fixed build error] Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Sun, 6 Nov 2011 15:49:37 +0000 (21:19 +0530)]
ARM: EXYNOS: Add ioremap interceptor for statically remapped regions
ioremap() request for statically remapped regions are intercepted
and the statically assigned virtual address is returned. For requests
for which there are no statically remapped regions, the requests are
let through.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Wed, 2 Nov 2011 10:13:25 +0000 (19:13 +0900)]
ARM: SAMSUNG: Move timer irq numbers to end of linux irq space
The timer irqs statically mapped from linux irq numbers 11 to 15 are
moved to the end of the statically mapped linux irq space. The GIC PPI
and SPI interrupts are relocated to start from 16 and 32 of the linux
irq space. This is a required to add device tree support for GIC and
Interrupt combiner for EXYNOS4.
A new macro 'IRQ_TIMER_BASE' specifies a platform specific base of the
linux virq number for the timer interrupts. For exynos4, this base is
set to end of the linux virq space. For the other S5P platforms, the
existing base '11' is retained.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Linus Torvalds [Tue, 8 Nov 2011 00:16:02 +0000 (16:16 -0800)]
Linux 3.2-rc1
.. with new name. Because nothing says "really solid kernel release"
like naming it after an extinct animal that just happened to be in the
news lately.
Al Viro [Mon, 7 Nov 2011 21:21:26 +0000 (21:21 +0000)]
VFS: we need to set LOOKUP_JUMPED on mountpoint crossing
Mountpoint crossing is similar to following procfs symlinks - we do
not get ->d_revalidate() called for dentry we have arrived at, with
unpleasant consequences for NFS4.
Linus Torvalds [Mon, 7 Nov 2011 20:38:11 +0000 (12:38 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf top: Fix live annotation in the --stdio interface
perf top tui: Don't recalc column widths considering just the first page
perf report: Add progress bar when processing time ordered events
perf hists browser: Warn about lost events
perf tools: Fix a typo of command name as trace-cmd
perf hists: Fix recalculation of total_period when sorting entries
perf header: Fix build on old systems
perf ui browser: Handle K_RESIZE in dialog windows
perf ui browser: No need to switch char sets that often
perf hists browser: Use K_TIMER
perf ui: Rename ui__warning_paranoid to ui__error_paranoid
perf ui: Reimplement the popup windows using libslang
perf ui: Reimplement ui__popup_menu using ui__browser
perf ui: Reimplement ui_helpline using libslang
perf ui: Improve handling sigwinch a bit
perf ui progress: Reimplement using slang
perf evlist: Fix grouping of multiple events
Tony Lindgren [Mon, 7 Nov 2011 20:27:10 +0000 (12:27 -0800)]
ARM: OMAP: Fix export.h or module.h includes
Commit 32aaeffbd4a7457bf2f7448b33b5946ff2a960eb (Merge branch
'modsplit-Oct31_2011'...) caused some build errors. Fix these
and make sure we always have export.h or module.h included
for MODULE_ and EXPORT_SYMBOL users:
Axel Lin [Mon, 7 Nov 2011 20:27:10 +0000 (12:27 -0800)]
ARM: OMAP: omap_device: Include linux/export.h
Include linux/export.h to fix below build warning:
CC arch/arm/plat-omap/omap_device.o
arch/arm/plat-omap/omap_device.c:1055: warning: data definition has no type or storage class
arch/arm/plat-omap/omap_device.c:1055: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
arch/arm/plat-omap/omap_device.c:1055: warning: parameter names (without types) in function declaration
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
forcedeth: fix a few sparse warnings (variable shadowing)
forcedeth: Improve stats counters
forcedeth: remove unneeded stats updates
forcedeth: Acknowledge only interrupts that are being processed
forcedeth: fix race when unloading module
MAINTAINERS/rds: update maintainer
wanrouter: Remove kernel_lock annotations
usbnet: fix oops in usbnet_start_xmit
ixgbe: Fix compile for kernel without CONFIG_PCI_IOV defined
etherh: Add MAINTAINERS entry for etherh
bonding: comparing a u8 with -1 is always false
sky2: fix regression on Yukon Optima
netlink: clarify attribute length check documentation
netlink: validate NLA_MSECS length
i825xx:xscale:8390:freescale: Fix Kconfig dependancies
macvlan: receive multicast with local address
tg3: Update version to 3.121
tg3: Eliminate timer race with reset_task
tg3: Schedule at most one tg3_reset_task run
tg3: Obtain PCI function number from device
...
david decotigny [Sat, 5 Nov 2011 14:38:24 +0000 (14:38 +0000)]
forcedeth: fix a few sparse warnings (variable shadowing)
This fixes the following sparse warnings:
drivers/net/ethernet/nvidia/forcedeth.c:2113:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2102:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2155:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2102:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2227:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2215:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2271:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2215:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2986:20: warning: symbol 'addr' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2963:6: originally declared here
Signed-off-by: David Decotigny <david.decotigny@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mandeep Baines [Sat, 5 Nov 2011 14:38:23 +0000 (14:38 +0000)]
forcedeth: Improve stats counters
Rx byte count was off; instead use the hardware's count. Tx packet
count was counting pre-TSO packets; instead count on-the-wire packets.
Report hardware dropped frame count as rx_fifo_errors.
- The count of transmitted packets reported by the forcedeth driver
reports pre-TSO (TCP Segmentation Offload) packet counts and not the
count of the number of packets sent on the wire. This change fixes
the forcedeth driver to report the correct count. Fixed the code by
copying the count stored in the NIC H/W to the value reported by the
driver.
- Count rx_drop_frame errors as rx_fifo_errors:
We see a lot of rx_drop_frame errors if we disable the rx bottom-halves
for too long. Normally, rx_fifo_errors would be counted in this case.
The rx_drop_frame error count is private to forcedeth and is not
reported by ifconfig or sysfs. The rx_fifo_errors count is currently
unused in the forcedeth driver. It is reported by ifconfig as overruns.
This change reports rx_drop_frame errors as rx_fifo_errors.
Signed-off-by: David Decotigny <david.decotigny@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
david decotigny [Sat, 5 Nov 2011 14:38:22 +0000 (14:38 +0000)]
forcedeth: remove unneeded stats updates
Function ndo_get_stats() updates most of the stats from hardware
registers, making the manual updates un-needed. This change removes
these manual updates. Main exception is rx_missed_errors which needs
manual update.
Another exception is rx_packets, still updated manually in this commit
to make sure this patch doesn't change behavior of driver. This will
be addressed by a future patch.
Signed-off-by: David Decotigny <david.decotigny@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Ditto [Sat, 5 Nov 2011 14:38:21 +0000 (14:38 +0000)]
forcedeth: Acknowledge only interrupts that are being processed
This is to avoid a race, accidentally acknowledging an interrupt that
we didn't notice and won't immediately process. This is based solely
on code inspection; it is not known if there was an actual bug here.
Signed-off-by: David Decotigny <david.decotigny@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
david decotigny [Sat, 5 Nov 2011 14:38:20 +0000 (14:38 +0000)]
forcedeth: fix race when unloading module
When forcedeth module is unloaded, there exists a path that can lead
to mod_timer() after del_timer_sync(), causing an oops. This patch
short-circuits this unneeded path, which originates in
nv_get_ethtool_stats().
Tested:
x86_64 16-way + 3 ethtool -S infinite loops + 100Mbps incoming traffic
+ rmmod/modprobe/ifconfig in a loop
Paul Gortmaker [Wed, 28 Sep 2011 22:29:32 +0000 (18:29 -0400)]
drivers/md: change module.h -> export.h in persistent-data/dm-*
For the files which are not themselves modular, we can change
them to include only the smaller export.h since all they are
doing is looking for EXPORT_SYMBOL.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Gortmaker [Sun, 9 Oct 2011 03:24:48 +0000 (23:24 -0400)]
arm: Add export.h to recently added files for EXPORT_SYMBOL
These files didn't exist at the time of the module.h split, and
so were not fixed by the commits on that baseline. Since they use
the EXPORT_SYMBOL and/or THIS_MODULE macros, they will need the
new export.h file included that provides them.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the bug added in commit v3.1-rc7-1055-gf9b491e
SKB can be NULL at this point, at least for cdc-ncm.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 7 Nov 2011 18:13:52 +0000 (10:13 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
cpuidle: Single/Global registration of idle states
cpuidle: Split cpuidle_state structure and move per-cpu statistics fields
cpuidle: Remove CPUIDLE_FLAG_IGNORE and dev->prepare()
cpuidle: Move dev->last_residency update to driver enter routine; remove dev->last_state
ACPI: Fix CONFIG_ACPI_DOCK=n compiler warning
ACPI: Export FADT pm_profile integer value to userspace
thermal: Prevent polling from happening during system suspend
ACPI: Drop ACPI_NO_HARDWARE_INIT
ACPI atomicio: Convert width in bits to bytes in __acpi_ioremap_fast()
PNPACPI: Simplify disabled resource registration
ACPI: Fix possible recursive locking in hwregs.c
ACPI: use kstrdup()
mrst pmu: update comment
tools/power turbostat: less verbose debugging
Linus Torvalds [Mon, 7 Nov 2011 18:01:56 +0000 (10:01 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (40 commits)
vmwgfx: Snoop DMA transfers with non-covering sizes
vmwgfx: Move the prefered mode first in the list
vmwgfx: Unreference surface on cursor error path
vmwgfx: Free prefered mode on error path
vmwgfx: Use pointer return error codes
vmwgfx: Fix hw cursor position
vmwgfx: Infrastructure for explicit placement
vmwgfx: Make the preferred autofit mode have a 60Hz vrefresh
vmwgfx: Remove screen object active list
vmwgfx: Screen object cleanups
drm/radeon/kms: consolidate GART code, fix segfault after GPU lockup V2
drm/radeon/kms: don't poll forever if MC GDDR link training fails
drm/radeon/kms: fix DP setup on TRAVIS bridges
drm/radeon/kms: set HPD polarity in hpd_init()
drm/radeon/kms: add MSI module parameter
drm/radeon/kms: Add MSI quirk for Dell RS690
drm/radeon/kms: Add MSI quirk for HP RS690
drm/radeon/kms: split MSI check into a separate function
vmwgfx: Reinstate the update_layout ioctl
drm/radeon/kms: always do extended edid probe
...
Linus Torvalds [Mon, 7 Nov 2011 17:11:16 +0000 (09:11 -0800)]
Merge git://git.infradead.org/mtd-2.6
* git://git.infradead.org/mtd-2.6: (226 commits)
mtd: tests: annotate as DANGEROUS in Kconfig
mtd: tests: don't use mtd0 as a default
mtd: clean up usage of MTD_DOCPROBE_ADDRESS
jffs2: add compr=lzo and compr=zlib options
jffs2: implement mount option parsing and compression overriding
mtd: nand: initialize ops.mode
mtd: provide an alias for the redboot module name
mtd: m25p80: don't probe device which has status of 'disabled'
mtd: nand_h1900 never worked
mtd: Add DiskOnChip G3 support
mtd: m25p80: add EON flash EN25Q32B into spi flash id table
mtd: mark block device queue as non-rotational
mtd: r852: make r852_pm_ops static
mtd: m25p80: add support for at25df321a spi data flash
mtd: mxc_nand: preset_v1_v2: unlock all NAND flash blocks
mtd: nand: switch `check_pattern()' to standard `memcmp()'
mtd: nand: invalidate cache on unaligned reads
mtd: nand: do not scan bad blocks with NAND_BBT_NO_OOB set
mtd: nand: wait to set BBT version
mtd: nand: scrub BBT on ECC errors
...
Fix up trivial conflicts:
- arch/arm/mach-at91/board-usb-a9260.c
Merged into board-usb-a926x.c
- drivers/mtd/maps/lantiq-flash.c
add_mtd_partitions -> mtd_device_register vs changed to use
mtd_device_parse_register.
vmwgfx: Snoop DMA transfers with non-covering sizes
Enough to get cursors working under Wayland.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Make it possible to use explicit placement
(although not hooked up with a user-space interface yet)
and relax the single framebuffer limit to only apply to implicit placement.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
vmwgfx: Make the preferred autofit mode have a 60Hz vrefresh
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Michael Neuling [Mon, 7 Nov 2011 06:12:28 +0000 (17:12 +1100)]
powerpc: fix building hvc_opal.c
Fix building following build error:
drivers/tty/hvc/hvc_opal.c:244:12: error: 'THIS_MODULE' undeclared here (not in a function)
Signed-off-by: Michael Neuling <mikey@neuling.org>
[ New file from powerpc tree not following the new rules from the
module.h split, both of which were merged today. - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 7 Nov 2011 04:20:46 +0000 (20:20 -0800)]
Merge branch 'upstream/jump-label-noearly' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen
* 'upstream/jump-label-noearly' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
jump-label: initialize jump-label subsystem much earlier
x86/jump_label: add arch_jump_label_transform_static()
s390/jump-label: add arch_jump_label_transform_static()
jump_label: add arch_jump_label_transform_static() to optimise non-live code updates
sparc/jump_label: drop arch_jump_label_text_poke_early()
x86/jump_label: drop arch_jump_label_text_poke_early()
jump_label: if a key has already been initialized, don't nop it out
stop_machine: make stop_machine safe and efficient to call early
jump_label: use proper atomic_t initializer
Conflicts:
- arch/x86/kernel/jump_label.c
Added __init_or_module to arch_jump_label_text_poke_early vs
removal of that function entirely
- kernel/stop_machine.c
same patch ("stop_machine: make stop_machine safe and efficient
to call early") merged twice, with whitespace fix in one version
Linus Torvalds [Mon, 7 Nov 2011 04:15:05 +0000 (20:15 -0800)]
Merge branch 'upstream/xen-settime' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen
* 'upstream/xen-settime' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen/dom0: set wallclock time in Xen
xen: add dom0_op hypercall
xen/acpi: Domain0 acpi parser related platform hypercall
Linus Torvalds [Mon, 7 Nov 2011 04:03:41 +0000 (20:03 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (114 commits)
Btrfs: check for a null fs root when writing to the backup root log
Btrfs: fix race during transaction joins
Btrfs: fix a potential btrfs_bio leak on scrub fixups
Btrfs: rename btrfs_bio multi -> bbio for consistency
Btrfs: stop leaking btrfs_bios on readahead
Btrfs: stop the readahead threads on failed mount
Btrfs: fix extent_buffer leak in the metadata IO error handling
Btrfs: fix the new inspection ioctls for 32 bit compat
Btrfs: fix delayed insertion reservation
Btrfs: ClearPageError during writepage and clean_tree_block
Btrfs: be smarter about committing the transaction in reserve_metadata_bytes
Btrfs: make a delayed_block_rsv for the delayed item insertion
Btrfs: add a log of past tree roots
btrfs: separate superblock items out of fs_info
Btrfs: use the global reserve when truncating the free space cache inode
Btrfs: release metadata from global reserve if we have to fallback for unlink
Btrfs: make sure to flush queued bios if write_cache_pages waits
Btrfs: fix extent pinning bugs in the tree log
Btrfs: make sure btrfs_remove_free_space doesn't leak EAGAIN
Btrfs: don't wait as long for more batches during SSD log commit
...
projects / karo-tx-linux.git / log