The new hardware design applied for this cards.
Silicon Labs C8051F300 microcontroller is used for LNB power control.
It connected to cx23885 GPIO pins:
GPIO0 - P0.3 data
GPIO1 - P0.2 reset
GPIO2 - P0.1 clk
GPIO3 - P0.0 busy
Tevii S470 based on Montage Technology M88TS2020 digital satellite tuner
and M88DS3000 advanced DVB-S/S2 demodulator.
Signed-off-by: Igor M. Liplianin <liplianin@me.by> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 25 Nov 2009 14:27:16 +0000 (11:27 -0300)]
V4L/DVB (13476): spec: remove old dvb-spec and v4l2-spec directories
It was really confusing to have media-specs, v4l2-spec and dvb-spec.
So this patch removes v4l2-spec and dvb-spec. The docs in dvb-spec and
the V4L1_API.html file were moved to media-specs/old-docs.
Removed all references to v4l2-spec and dvb-spec.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pete Eberlein [Mon, 16 Nov 2009 18:07:42 +0000 (15:07 -0300)]
V4L/DVB (13455): go7007: Add struct v4l2_device.
This adds a struct v4l2_device to the go7007 device struct and registers
it during v4l2 initialization. The v4l2_device registration overwrites
the go->dev device_data, which is a struct usb_interface with intfdata set
to the struct go7007. This changes intfdata to point to the struct
v4l2_device inside struct go7007, which is what v4l2_device_register will
also set it to (and warn about non-null drvdata on register.) Since usb
disconnect can happen any time, this intfdata should always be present.
Signed-off-by: Pete Eberlein <pete@sensoray.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sat, 21 Nov 2009 19:19:27 +0000 (16:19 -0300)]
V4L/DVB (13446): ivtv: Add more explicit detection of known IR devices for Hauppauge cards
Avoid legacy IR I2C probing for PVR-150, PVR-500, and PVR-350 cards. This
still probes, but restricts the possbile addresses probed per card.
Also removed legacy probe addresses for the KNC and PixelView cards which are
not supported by ivtv as far as I know.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sat, 21 Nov 2009 16:39:28 +0000 (13:39 -0300)]
V4L/DVB (13445): cx18: Use per cx18 instance init data for ir-kbd-i2c instead of const data
This change creates per cx18 instances of IR_i2c_init_data for handing over
initialization data to ir-kbd-i2c, since that module wants non-const data
even though it never modifies the data.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sat, 21 Nov 2009 15:52:34 +0000 (12:52 -0300)]
V4L/DVB (13444): ivtv: Add explicit IR controller initialization for the AVerTV M116
Add explicit support for the AVerTV M116 for use with the ir-kbd-i2c module.
This also eases future support for other AVerMedia ivtv boards with the same
microcontroller program at I2C address 0x40.
This is a reworked version of an earlier patch that was...
Reviewed-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sat, 21 Nov 2009 14:41:33 +0000 (11:41 -0300)]
V4L/DVB (13443): ivtv: Defer legacy I2C IR probing until after setup of known I2C devices
This avoids collisions of legacy IR controller probing with known I2C devices
in the card definitions in ivtv-cards.c. I2C driver modules for device listed
explicitly in a card definition should always take precedence over a probe
guessing where and IR controller may be.
Reviewed-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sat, 21 Nov 2009 04:47:45 +0000 (01:47 -0300)]
V4L/DVB (13442): ivtv: Add module parameter to adjust I2C SCL clock period per board
Add a module parameter to adjust I2C SCL clock period per board. This allows
some experimental fine tuning by end users to overcome quirky I2C device
problems.
Reported-by: "Aleksandr V. Piskunov" <aleksandr.v.piskunov@gmail.com> Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB (13441): ivtv: Added FM radio support to Avermedia AVerTV MCE 116 Plus card
Signed-off-by: Aleksandr V. Piskunov <alexandr.v.piskunov@gmail.com> Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Wed, 11 Nov 2009 02:28:30 +0000 (23:28 -0300)]
V4L/DVB (13431): cx18: Adjust an MDL's final buffer size to force encoder transfer size
The encoder was not honoring the MDL size sent in DE_SET_MDL mailbox commands.
This change adjusts the size of the last buffer in an MDL, as reported to the
firmware, so that the encoder will send the exact amount of bytes we specify
per MDL transfer. This eliminates tearing in YUV playback when using
non-default YUV buffer sizes.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Tue, 10 Nov 2009 02:55:30 +0000 (23:55 -0300)]
V4L/DVB (13430): cx18: Fix YUV capture so that encoder passes a single frame per transfer
Fix YUV capture such that the encoder will pass one frame per transfer. This
will allow the application to maintain frame alignment when a transfer from
the encoder is missed due to high system latency in service the CX23418 IRQ.
Also force YUV buffer sizes to be specified in multiples of 33.75 kB, the
smalled amount of buffer sizes need to store a complete set of HM12 4:2:0
macroblocks specifying 32 lines of the frame. A full 60Hz/525 line
screen requires 15 * 33.75 kB per frame and a full 50Hz/625 line screen
requires 18 * 33.75 kB per frame so the default buffer size is 3 * 33.75 kB,
requiring exactly 5 or 6 buffers per MDL respectively. The bytes needed per
frame and hence MDL need not be the bytes in an integer number of buffers.
However, if frame artifacts are seen with scaled screen sizes, the YUV buffer
size can be set 34 kB (33.75 kB) to get rid of the artifacts at the cost of more
copies between the kernel and userspace.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add debug register write interface to pac7302 to be able to set
for example the edge detect mode (bit 2 register 0x55) or the
test pattern (bit 0..3, register 0x72) and test overlay (bit 4,
register 0x72) from the user space. Only write of register
page 0 is supported by this patch.
For whatever reason, the device structure pointer to
videobuf_queue_vmalloc_init is typed "void *", even though it's passed
right through to videobuf_queue_core_init(), which expects a struct
device pointer. The other videobuf implementations use struct device *;
I think vmalloc should too.
Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stefan Richter [Wed, 18 Nov 2009 19:01:14 +0000 (16:01 -0300)]
V4L/DVB (13409): firedtv: packet requeuing is likely to succeed
Packet DMA buffers are queued either initially all at once (then, a
queueing failure will cause firedtv to release the DMA context as a
whole) or subsequently one by one as they recycled after use (then a
failure is extremely unlikely). Therefore we can be a little less
cautious when counting at which packet buffer to set the interrupt flag.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cache only addresses of whole pages, not of each buffer chunk. Besides,
page addresses can be obtained by page_address() instead of kmap() since
they were allocated in lowmem.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stefan Richter [Sun, 8 Nov 2009 21:30:54 +0000 (18:30 -0300)]
V4L/DVB (13400): firedtv: port to new firewire core
The firedtv DVB driver will now work not only on top of the old ieee1394
driver stack but also on the new firewire driver stack.
Alongside to the firedtv-1394.c backend for driver binding and I/O, the
firedtv-fw.c backend is added. Depending on which of the two 1394
stacks is configured, one or the other or both backends will be built
into the firedtv driver.
This has been tested with a DVB-T and a DVB-C box on x86-64 and x86-32
together with a few different controllers (Agere FW323, a NEC chip, TI
TSB82AA2, TSB43AB22/A, VIA VT6306).
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stefan Richter [Sun, 8 Nov 2009 21:29:41 +0000 (18:29 -0300)]
V4L/DVB (13399): firedtv: add missing include, rename a constant
Add #include <dvb_demux.h> for dvb_dmx_swfilter_packets(). This was
already indirectly included via firedtv.h, but don't rely on it.
The 4 bytes which were referred to as FIREWIRE_HEADER_SIZE are actually
the source packet header from IEC 61883-4 (MPEG2-TS data transmission
over 1394), not e.g. the IEEE 1394 isochronous packet header. So choose
a more precise name.
Also, express the payload size as a preprocessor constant too.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Preparation for the port of firedtv to the firewire-core kernel API:
The fdtv->backend->lock() hook and thus the CMP code is slightly changed
to better fit with the new API.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stefan Richter [Sun, 8 Nov 2009 21:28:45 +0000 (18:28 -0300)]
V4L/DVB (13397): firedtv: move remote control workqueue handling into rc source file
Preparation for the port of firedtv to the firewire-core kernel API:
Canceling of the remote control workqueue job is factored into
firedtv-rc.c. Plus trivial whitespace change.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Julia Lawall [Sun, 8 Nov 2009 17:49:05 +0000 (14:49 -0300)]
V4L/DVB (13396): correct initialization of audio_mode
This initialization of the value of audio_mode is the one used if nothing
matches in the subsequent switch. The variable audio_mode is subsequently
assigned to constants such as TUNER_AUDIO_MONO and TUNER_AUDIO_STEREO.
TUNER_AUDIO_STEREO has the same value as V4L2_TUNER_MODE_STEREO, so it
would seem better to use that value here.
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB (13385): gspca - pac7302: Add red and blue balance control.
The valid values for these controls are 0..3 (lower two bits) which was
identified by trial and error on Labtec Webcam 2200 (USB ID 093a:2626).
The upper 6 bits are ignored on page 0, registers 0xc5 and 0xc7 by the camera.
The usb_control_msg() can fail any time. Only continue writing
sequence if there was no error with the previous write. If there
was any problem stop sending URBs and propagate the error to the
gspca_main.
where sizeof(cam->input_physname) returns length of cam->input_phisname
without length for null-symbol. But this parameter must be - "maximum
numbers of bytes to copy", i.e.:
sizeof(cam->input_physname)-strlen(cam->input_physname)-1.
In this case, after call to usb_make_path the similar drivers use strlcat.
where sizeof(cam->input_physname) returns length of cam->input_phisname
without length for null-symbol. But this parameter must be - "maximum
numbers of bytes to copy", i.e.:
sizeof(cam->input_physname)-strlen(cam->input_physname)-1.
In this case, after call to usb_make_path the similar drivers use strlcat.
Like in drivers/hid/usbhid/hid-core.c:
1152 usb_make_path(dev, hid->phys, sizeof(hid->phys));
1153 strlcat(hid->phys, "/input", sizeof(hid->phys));
Found by Linux Driver Verification Project.
Use strlcat instead of strncat.
Signed-off-by: Alexander Strakh <strakh@ispras.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jonathan Corbet [Tue, 17 Nov 2009 22:43:41 +0000 (19:43 -0300)]
V4L/DVB (13377): make struct videobuf_queue_ops constant
The videobuf_queue_ops function vector is not declared constant, but
there's no need for the videobuf layer to ever change it. Make it const
so that videobuf users can make their operations const without warnings.
Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB (13368): af9015: support for Sveon STV20 Tuner USB DVB-T HDTV
Add USB ID 1b80:e39d for Sveon STV20 Tuner USB DVB-T HDTV.
Signed-off-by: Ignacio de Miguel Diaz <imigueldiaz@gmail.com> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Fri, 13 Nov 2009 21:22:02 +0000 (18:22 -0300)]
V4L/DVB (13360): stv090x: fix the calculation of the r divider in stv6110x_set_frequency
It had always the value 3 no matter what frequency was given.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Fri, 13 Nov 2009 21:20:54 +0000 (18:20 -0300)]
V4L/DVB (13359): stv090x: adds corrections of some register values
While here, also do some blind scan related fixes.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Fri, 13 Nov 2009 21:19:54 +0000 (18:19 -0300)]
V4L/DVB (13358): stv090x: add an additional check for packet delineator lock in stv090x_read_status in case of a tuned DVB-S2 signal
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Fri, 13 Nov 2009 21:18:53 +0000 (18:18 -0300)]
V4L/DVB (13357): stv090x: adds an additional check for signal presence based on AGC1
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Fri, 13 Nov 2009 21:17:45 +0000 (18:17 -0300)]
V4L/DVB (13356): stv090x: fixes signal lock logic
This patch contains several fixes for the stv090x driver:
- added missing else
- use calculated timeout instead of fixed one
- use correct frequency when doing zigzag scan
- added missing read of GENCFG register
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Fri, 13 Nov 2009 21:16:44 +0000 (18:16 -0300)]
V4L/DVB (13355): stv090x: fixes calculation of AGC2 and uses a different AGC2 threshold for cut 3 chips
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Fri, 13 Nov 2009 21:15:27 +0000 (18:15 -0300)]
V4L/DVB (13354): stv090x: fixes some typos like wrong register or variable names
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Fri, 13 Nov 2009 21:14:00 +0000 (18:14 -0300)]
V4L/DVB (13353): stv090x: fixes STR and SNR calculation and normalizes the value into the 0..0xFFFF range
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Fri, 13 Nov 2009 21:12:48 +0000 (18:12 -0300)]
V4L/DVB (13352): stv090x: fixes errors and typos in register definitions
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
projects / karo-tx-linux.git / log