OMAPDSS: VENC: allow switching venc output type at runtime
VENC output type (composite/svideo) doesn't have to be fixed by board
wiring, it is possible to also provide composite signal through svideo
luminance connector (software enabled), which is what pandora does.
Having to recompile the kernel for users who have TV connector types
that don't match default board setting is very inconvenient, especially
for users of a consumer device, so add support for switching VENC output
type at runtime over a new sysfs file output_type.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Wed, 9 May 2012 10:50:32 +0000 (13:50 +0300)]
Merge branch 'archit/set-timing-work'
An overlay manager's timings (the manager size, and blanking parameters
if an LCD manager) are DISPC shadow registers, and they should hence
follow the correct programming model.
This series makes the video timings an extra_info parameter in manager's
private data. The interface drivers now apply the timings instead of
directly writing to registers.
This change also prevents the need to use display resolution for overlay
checks, hence making some of the APPLY functions less dependent on the
display. Some DISPC functions that needed display width can also use
these privately stored timings.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Archit Taneja [Tue, 8 May 2012 10:23:20 +0000 (15:53 +0530)]
OMAPDSS: DISPC: Remove usage of dispc_mgr_get_device()
The functions calc_fclk_five_taps() and check_horiz_timing_omap3() use the
function dispc_mgr_get_device() to get the omap_dss_device pointer to which
the manager is connected, the width of the panel is derived from that.
The manager's timing is stored in it's private data in APPLY. This contains
the latest timings applied to the manager. Pass these timings to
dispc_ovl_setup() and use them in the above functions. Remove the function
dispc_mgr_get_device() as it isn't used any more.
OMAPDSS: DISPC: Remove omap_dss_device pointer usage from dispc_mgr_pclk_rate()
The pixel clock rate for the TV manager is calculated by checking the device
type connected to the manager, and then requesting the VENC/HDMI interface for
the pixel clock rate.
Remove the use of omap_dss_device pointer from here by checking which interface
generates the pixel clock by reading the DSS_CTRL.VENC_HDMI_SWITCH bit.
Archit Taneja [Thu, 3 May 2012 14:33:11 +0000 (20:03 +0530)]
OMAPDSS: DPI/HDMI: Apply manager timings even if panel is disabled
The DPI and HDMI interfaces use their 'set_timing' functions to take in a new
set of timings. If the panel is disabled, they do not disable and re-enable
the interface. Currently, the manager timings are applied in hdmi_power_on()
and dpi_set_mode() respectively, these are not called by set_timings if the
panel is disabled.
When checking overlay and manager data, the DSS driver uses the last applied
manager timings, and not the timings held by omap_dss_device struct. Hence,
there is a need to apply the new manager timings even if the panel is disabled.
Apply the manager timings if the panel is disabled. Eventually, there should be
one common place where the timings are applied independent of the state of the
panel.
OMAPDSS: APPLY: Remove display dependency from overlay and manager checks
In order to check the validity of overlay and manager info, there was a need to
use the omap_dss_device struct to get the panel resolution. The manager's
private data in APPLY now contains the manager timings. Hence, we don't need to
rely on the display resolution any more.
Pass the manager's timings in private data to dss_mgr_check(). Remove the need
to pass omap_dss_device structs in the functions which check for the validity
of overlay and manager parameters.
Archit Taneja [Tue, 8 May 2012 12:49:15 +0000 (18:19 +0530)]
OMAPDSS: APPLY: Don't check manager settings if it is disabled
If a manager is disabled, there is no guarantee at any point in time that all
it's parameters are configured. There is always a chance that some more
parameters are yet to be configured by a user of DSS, or by DSS itself.
However, when the manager is enabled, we can be certain that all the parameters
have been configured, as we can't enable a manager with an incomplete
configuration. Therefore, if a manager is disabled, don't check for the validity
of it's parameters or the parameters of the overlays connected to it. Only check
once it is enabled. Add a check in dss_check_settings_low() to achieve the same.
OMAPDSS: MANAGER: Create a function to check manager timings
Create a function dss_mgr_check_timings() which wraps around the function
dispc_mgr_timings_ok(). This is mainly a clean up to hide dispc functions
from interface drivers.
dss_mgr_check_timings() is added in the function dss_mgr_check(), it currently
takes the timings maintained in the omap_dss_device struct. This would be later
replaced by the timings stored in the manager's private data.
Make dss_mgr_check_timings() and dispc_mgr_timings_ok() take a const
omap_video_timings pointer since these functions just check the timings.
OMAPDSS: Apply manager timings instead of direct DISPC writes
Replace the function dispc_mgr_set_timings() with dss_mgr_set_timings() in the
interface drivers. The latter function ensures that the timing related DISPC
registers are configured according to the shadow register programming model.
Remove the call to dispc_mgr_go() in dpi_set_timings() as the manager's go bit
is set by dss_mgr_set_timings().
OMAPDSS: APPLY: Add manager timings as extra_info in private data
DISPC manager size and DISPC manager blanking parameters(for LCD managers)
follow the shadow register programming model. Currently, they are programmed
directly by the interface drivers.
To configure manager timings using APPLY, there is a need to introduce extra
info flags for managers, similar to what is done for overlays. This is needed
because timings aren't a part of overlay_manager_info struct configured by a
user of DSS, they are configured internally by the interface or panel drivers.
Add dirty and shadow_dirty extra_info flags for managers, update these flags
at the appropriate places. Rewrite the function extra_info_update_ongoing()
slightly as checking for manager's extra_info flags can simplify the code a bit.
Create function dss_mgr_set_timings() which applies the new manager timings to
extra_info.
Archit Taneja [Mon, 7 May 2012 11:21:36 +0000 (16:51 +0530)]
OMAPDSS: DISPC: Remove Fake VSYNC support
Fake VSYNC support is a hack and has some bugs in it. It isn't used by any user
of DSS. Remove Fake VSYNC support. For DSI command mode and RFBI panels, a user
of DSS should wait for the completion of a frame by using the panel driver's
sync op.
Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Archit Taneja [Mon, 7 May 2012 11:21:35 +0000 (16:51 +0530)]
OMAPDSS: Fix DSI_FCLK clock source selection
The wrong bit field was being updated in DSS_CTRL when trying to configure the
clock source of DSI2 functional clock. Use the correct bit field based on the
dsi module number.
Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Archit Taneja [Mon, 7 May 2012 13:20:28 +0000 (18:50 +0530)]
OMAPDSS: HDMI: define and dump CORE registers in correct order
The HDMI core register offset macros aren't defined in ascending order of their
values, some of the offset macros are also redefined. The same issues occur when
these core registers are dumped.
Clean up the ordering of HDMI core registers and remove repeated registers in
the definition in ti_hdmi_4xxx_ip.h and in ti_hdmi_4xxx_core_dump().
Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Archit Taneja [Mon, 7 May 2012 13:20:27 +0000 (18:50 +0530)]
OMAPDSS: HDMI: Fix ti_hdmi_4xxx_core_dump
The function ti_hdmi_4xxx_core_dump has some bugs, the following mention the
bugs and the solutions:
- The macros DUMPCORE and DUMPCOREAV in ti_hdmi_4xxx_core_dump() use
hdmi_pll_base() for the offsets needed to calculate register addresses, use
functions hdmi_core_sys_base() amd hdmi_av_base() to calculate the correct
offsets for CORE_SYS and CORE_AV registers.
- Many of the CORE_AV registers use the DUMPCORE macro, and hence the register
addresses are calculated incorrectly. Rename the current DUMPCOREAV macro as
DUMPCOREAV2 as it takes 2 arguments to dump indexed CORE_AV registers, create
a new macro called DUMPCOREAV which is now used for dumping non-indexed
CORE_AV registers.
Thanks to Ancy Tom <ancytom@gmail.com> for pointing out the issues.
Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Wed, 28 Mar 2012 12:58:56 +0000 (15:58 +0300)]
OMAPDSS: DSI: implement generic DSI pin config
In preparation for device tree, this patch changes how the DSI pins are
configured. The current configuration method is only doable with board
files and the configuration data is OMAP specific.
This patch moves the configuration data to the panel's platform data,
and the data can easily be given via DT in the future. The configuration
data format is also changed to a generic one which should be suitable
for all platforms.
The new format is an array of pin numbers, where the array items start
from clock + and -, then data1 + and -, and so on. For example:
{
0, // pin num for clock lane +
1, // pin num for clock lane -
2, // pin num for data1 lane +
3, // pin num for data1 lane -
...
}
The pin numbers are translated by the DSI driver and used to configure
the hardware appropriately.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by: Tony Lindgren <tony@atomide.com>
Tomi Valkeinen [Mon, 20 Feb 2012 10:18:52 +0000 (12:18 +0200)]
OMAPDSS: Taal: move reset gpio handling to taal driver
The reset GPIO for Taal panel driver is currently requested in the
4430sdp board file. This patch moves the gpio request/free into the Taal
driver, where it should be.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by: Tony Lindgren <tony@atomide.com>
DISPC_FCLK is incorrectly used as functional clock of DISPC in scaling
calculations. So, DISPC_CORE_CLK replaces as functional clock of DISPC.
DISPC_CORE_CLK is derived from DISPC_FCLK divided by an independent DISPC
divisor LCD.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In OMAP3 DISPC video overlays suffer from some undocumented horizontal position
and timing related limitations leading to SYNCLOST errors. Whenever the image
window is moved towards the right of the screen SYNCLOST errors become
frequent. Checks have been implemented to see that DISPC driver rejects
configuration exceeding above limitations.
This code was successfully tested on OMAP3. This code is written based on code
written by Ville Syrjälä <ville.syrjala@nokia.com> in Linux OMAP kernel. Ville
Syrjälä <ville.syrjala@nokia.com> had added checks for video overlay horizontal
timing and DISPC horizontal blanking length limitations.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In OMAP3 and OMAP4, the DISPC Scaler can downscale an image up to 4 times, and
up to 2 times in OMAP2. However, with predecimation, the image can be reduced
to 16 times by fetching only the necessary pixels in memory. Then this
predecimated image can be downscaled further by the DISPC scaler.
The pipeline is configured to use a burst of size 8 * 128 bits which consists
of 8 mini bursts of 16 bytes each. So, horizontal predecimation more than 16
can lead to complete discarding of such mini bursts. L3 interconnect may
handover the bus to some other initiator and inturn delay the fetching of
pixels leading to underflows. So, maximum predecimation limit is fixed at 16.
Based on the downscaling required, a prior calculation of predecimation values
for width and height of an image is done. Since, Predecimation reduces quality
of an image higher priorty is given to DISPC Scaler for downscaling.
This code was successfully tested on OMAP2, OMAP3 and OMAP4. Horizontal and
vertical predecimation worked fine except for some synclost errors due to
undocumented errata in OMAP3 which are fixed later and skewed images were seen
on OMAP2 and OMAP3 during horizontal predecimation which will be addressed in
the future patches.
This code is based on code written by Lajos Molnar <lajos@ti.com> who had added
predecimation support for NV12/YUV/rotated/SDMA buffers.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAPDSS: DISPC: Clean up manager timing/size functions
Clean up the DISPC manager timings related function by:
- Create a common function to set size for LCD and TV.
- Create a common function to check timings for LCD and TV.
- Add dss params to get the range of manager size.
Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAPDSS: DISPC: Use a common function to set manager timings
Currently, a LCD manager's timings is set by dispc_mgr_set_lcd_timings() and TV
manager's timings is set by dispc_set_digit_size(). Use a common function called
dispc_mgr_set_timings() which sets timings for both type of managers.
We finally want the interface drivers to use an overlay manager function to
configure it's timings, having a common DISPC function would make things
cleaner.
For LCD managers, dispc_mgr_set_timings() sets LCD size and blanking values, for
TV manager, it sets only the TV size since blanking values don't exist for TV.
Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAPDSS: DISPC/RFBI: Use dispc_mgr_set_lcd_timings() for setting lcd size
The RFBI driver uses dispc_mgr_set_lcd_size() to set the width and height of
the LCD manager. Replace this to use dispc_mgr_set_lcd_timings(), pass dummy
blanking parameters like done in the DSI driver.
This prevents the need to export dispc_mgr_set_lcd_size(), and use a common
function to set lcd timings.
Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
code depending on FB_OMAP_BOOTLOADER_INIT has been removed long before
(e.g. Tomi Valkeinen, 03 Mar 2011: OMAP: DSS2: Remove FB_OMAP_BOOTLOADER_INIT
support), but the option still exists Kconfig and has no use
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAPDSS: provide default get_timings function for panels
With this we can eliminate some duplicate code in panel drivers.
Also lgphilips-lb035q02, nec-nl8048hl11-01b, picodlp and
tpo-td043mtea1 gain support of reading timings over sysfs.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Mark Brown [Mon, 19 Mar 2012 15:02:32 +0000 (15:02 +0000)]
OMAPDSS: TPO-TD03MTEA1: Correct comment for power on delay
Since any power on stabilisation delay for the supply itself should be
taken care of transparently by the regulator API when the regulator is
enabled the additional delay that the TPO-TD03MTEA1 driver adds after
that returned should be due to the requirements of the device itself
rather than the supply (the delay is also suspicously long for one for
a regulator to ramp). Correct the comment to avoid misleading people
taking this code as a reference.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Mark Brown [Mon, 19 Mar 2012 15:02:31 +0000 (15:02 +0000)]
OMAPDSS: TPO-TD03MTEA1: Check for errors from regulator_enable()
It is possible for regulator_enable() to fail and if it does fail that's
generally a bad sign for anything we try to do with the hardware afterwards
so check for and immediately return an error if regulator_enable() fails.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Mark Brown [Mon, 19 Mar 2012 14:56:39 +0000 (14:56 +0000)]
OMAPDSS: VENC: Check for errors from regulator_enable()
It is possible for regulator_enable() to fail and if it does fail that's
generally a bad sign for anything we try to do with the hardware afterwards
so check for and immediately return an error if regulator_enable() fails.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Mark Brown [Mon, 19 Mar 2012 14:50:46 +0000 (14:50 +0000)]
OMAP: DSS2: Remove suspicous and unused TAAL regulator API usage
The TAAL driver contains some regulator support which is currently unused
(the code is there but the one panel supported by the driver doesn't have
any regulators provided). This code mostly looks like an open coded
version of the regulator core bulk API.
The only additional feature is that a voltage range can be set once when
the device is opened, though this is never varied at runtime. The general
expectation is that if the device is not actively managing the voltage of
the device (eg, doing DVFS) then any configuration will be done using the
constraints rather than by drivers, saving them code and ensuring that
they work well with systems where the voltage is not configurable.
If systems are added needing regulator support this can be added back in,
though it should be based on core features rather than open coding things.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Thu, 15 Mar 2012 13:22:58 +0000 (15:22 +0200)]
OMAPDSS: DSI: remove option to use pck for DSI PLL clkin
For some OMAP versions the TRM says that the pixel clock from DISPC can
be used as an input clock for DSI PLL, instead of the default, which is
sysclk. For some OMAP versions the bits affecting this are marked as
reserved. This feature has never been tested, so it's unknown if the HW
even works, and has never been used.
To clean things up, this patch removes the functionality. This should
not affect any board.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Thu, 8 Mar 2012 10:52:38 +0000 (12:52 +0200)]
OMAPDSS: Ensure OPP100 when DSS is operational
Most of the DSS clocks have restrictions on their frequency based on the
OPP in use. For example, maximum frequency for a clock may be 180MHz in
OPP100, but 90MHz in OPP50. This means that when a high enough pixel
clock or function clock is required, we need to use OPP100.
However, there's currently no way in the PM framework to make that kind
of request. The closest we get is to ask for very high bus throughput
from the PM framework, which should effectively force OPP100.
This patch is a simple version for handling the problem. Instead of
asking for OPP100 only when needed, this patch asks for OPP100 whenever
DSS is active. This obviously is not an optimal solution for cases with
small displays where OPP50 would work just fine. However, a proper
solution is a complex one, and this patch is a short term solution for
the problem.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Paul Walmsley <paul@pwsan.com> Acked-by: Kevin Hilman <khilman@ti.com>
Otherwise cpu_active_mask will not set, which lead to other issue.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com> Signed-off-by: Konrad Eisele <konrad@gaisler.com> Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'mmc-fixes-for-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- Build fix for omap_hsmmc with OF against 3.4-rc1.
- Fix CONFIG_MMC_UNSAFE_RESUME semantics regression against 3.3, which
broke hotplug card detection when UNSAFE_RESUME is set.
- Fix a race condition in omap_hsmmc with runtime PM.
- Fix two libertas SDIO-powered-resume regressions.
- Small fixes for discard/sanitize, dw_mmc, cd-gpio and esdhc-imx.
* tag 'mmc-fixes-for-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: core: Do not pre-claim host in suspend
mmc: dw_mmc: prevent NULL dereference for dma_ops
mmc: unbreak sdhci-esdhc-imx on i.MX25
mmc: cd-gpio: Include header to pickup exported symbol prototypes
mmc: sdhci: refine non-removable card checking for card detection
mmc: dw_mmc: Fix switch from DMA to PIO
mmc: remove MMC bus legacy suspend/resume method
mmc: omap_hsmmc: Get rid of of_have_populated_dt() usage
mmc: omap_hsmmc: build fix for CONFIG_OF=y and CONFIG_MMC_OMAP_HS=m
mmc: fixes for eMMC v4.5 sanitize operation
mmc: fixes for eMMC v4.5 discard operation
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- Fixes a regression at DVB core when switching from DVB-S2 to DVB-S on
Kaffeine (Fedora 16 Bugzilla #812895);
- Fixes a mutex unlock at an error condition at drx-k;
- Fix winbond-cir set mode;
- mt9m032: Fix a compilation breakage with some random Kconfig;
- mt9m032: fix two dead locks;
- xc5000: don't require an special firmware (that won't be provided by
the vendor) just because the xtal frequency is different;
- V4L DocBook: fix some typos at multi-plane formats description.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] xc5000: support 32MHz & 31.875MHz xtal using the 41.024.5 firmware
[media] V4L: mt9m032: fix compilation breakage
[media] V4L: DocBook: Fix typos in the multi-plane formats description
[media] V4L: mt9m032: fix two dead-locks
[media] rc-core: set mode for winbond-cir
[media] drxk: Does not unlock mutex if sanity check failed in scu_command()
[media] dvb_frontend: Fix a regression when switching back to DVB-S
Merge tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD fixes from Samuel Ortiz:
"We have 3 build fixes, a OMAP USB host PHY reset fix and the twl6040
conversion to an i2c driver. The latter may not sound like a fix but
the twl6040 MFD driver won't probe without it, triggering an OMAP4
audio regression."
* tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Fix modular builds of rc5t583 regulator support
mfd: Fix asic3_gpio_to_irq
ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue
mfd: Convert twl6040 to i2c driver, and separate it from twl core
mfd : Fix dbx500 compilation error
Al Viro [Sat, 21 Apr 2012 01:49:41 +0000 (21:49 -0400)]
aio: don't bother with unmapping when aio_free_ring() is coming from exit_aio()
... since exit_mmap() is coming and it will munmap() everything anyway.
In all other cases aio_free_ring() has ctx->mm == current->mm; moreover,
all other callers of vm_munmap() have mm == current->mm, so this will
allow us to get rid of mm argument of vm_munmap().
Now, dma_ops is assumed that use the IDMAC. But if dma_ops is assigned
the pdata->dma_ops, we didn't ensure that callback function is defined.
If the callback isn't defined, then we should run in PIO mode.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Eric Bénard [Wed, 18 Apr 2012 00:30:20 +0000 (02:30 +0200)]
mmc: unbreak sdhci-esdhc-imx on i.MX25
This was broken by me in 37865fe91582582a6f6c00652f6a2b1ff71f8a78
("mmc: sdhci-esdhc-imx: fix timeout on i.MX's sdhci") where more
extensive tests would have shown that read or write of data to the
card were failing (even if the partition table was correctly read).
Signed-off-by: Eric Bénard <eric@eukrea.com> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Cc: stable <stable@vger.kernel.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Daniel Drake [Mon, 9 Apr 2012 23:14:20 +0000 (00:14 +0100)]
mmc: sdhci: refine non-removable card checking for card detection
Commit c79396c191bc19 ("mmc: sdhci: prevent card detection activity
for non-removable cards") disables card detection where the cards
are marked as non-removable.
This makes sense, but the implementation detail of calling
mmc_card_is_removable() causes some problems, because
mmc_card_is_removable() is overloaded with CONFIG_MMC_UNSAFE_RESUME
semantics.
In the OLPC XO case, we need CONFIG_MMC_UNSAFE_RESUME because our root
filesystem is stored on SD, but we also have external SD card slots
where we want automatic card detection.
Refine the check to only apply to hosts marked as MMC_CAP_NONREMOVABLE,
which is defined to mean that the card is *really* nonremovable. This
could be revisited in future if we find a way to improve
CONFIG_MMC_UNSAFE_RESUME semantics.
Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
[stable@: please apply to 3.3-stable] Cc: stable <stable@vger.kernel.org> Signed-off-by: Chris Ball <cjb@laptop.org>
When dw_mci_pre_dma_transfer returns failure in some reasons,
dw_mci_submit_data will prepare to switch the PIO mode from DMA.
After switching to PIO mode, DMA(IDMAC in particular) is still
enabled. This makes the corruption in handling interrupt and
the driver lock-up.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
MMC bus is using legacy suspend/resume method, which is not compatible if
runtime pm callbacks are used. In this scenario, MMC bus suspend/resume
callbacks cannot be called when system entering S3. So change to use the
new defined dev_pm_ops for system sleeping mode.
Tested on AM335x Platform. Solves major issue/crash reported at
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg65425.html
This continues the theme started with vm_brk() and vm_munmap():
vm_mmap() does the same thing as do_mmap(), but additionally does the
required VM locking.
This uninlines (and rewrites it to be clearer) do_mmap(), which sadly
duplicates it in mm/mmap.c and mm/nommu.c. But that way we don't have
to export our internal do_mmap_pgoff() function.
Some day we hopefully don't have to export do_mmap() either, if all
modular users can become the simpler vm_mmap() instead. We're actually
very close to that already, with the notable exception of the (broken)
use in i810, and a couple of stragglers in binfmt_elf.
mmc: omap_hsmmc: Get rid of of_have_populated_dt() usage
of_have_populated_dt() is not expected to be used in drivers but
instead only in early platform init code.
Drivers on the other hand should rely on dev->of_node or of_match_device().
Besides usage of of_have_populated_dt() also throws up build error as below
which was reported by Balaji TK, when omap_hsmmc is built as a module.
So get rid of all of_have_populated_dt() usage in omap_hsmmc driver and
instead use dev->of_node to make the same dicisions as earlier.
Signed-off-by: Rajendra Nayak <rnayak@ti.com> Reported-by: Benoit Cousson <b-cousson@ti.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Rob Herring <rob.herring@calxeda.com> Reviewed-by: Balaji T K <balajitk@ti.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Adrian Hunter [Thu, 5 Apr 2012 11:45:48 +0000 (14:45 +0300)]
mmc: fixes for eMMC v4.5 sanitize operation
eMMC v4.5 sanitize operation erases all copies of unmapped
data. However trim or erase operations must be used first
to unmap the required sectors. That was not being done.
Fixes apply to linux 3.2 on.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: <stable@vger.kernel.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Adrian Hunter [Thu, 5 Apr 2012 11:45:47 +0000 (14:45 +0300)]
mmc: fixes for eMMC v4.5 discard operation
eMMC v4.5 discard operation is significantly different from the
existing trim operation because it is not guaranteed to work with
the new sanitize operation. Consequently mmc_can_trim() is
separated from mmc_can_discard().
Also the new discard operation does not result in the sectors being
set to all-zeros, so discard_zeroes_data must not be set.
In addition, the new discard has the same timeout as trim, but from
v4.5 trim is defined to use the hc timeout. The timeout calculation
is adjusted accordingly.
Fixes apply to linux 3.2 on.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: <stable@vger.kernel.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Merge tag 'for-torvalds-20120418' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
- Fixed compilation errors and warnings
- Stricter checks on the ops vtable
* tag 'for-torvalds-20120418' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: implement pinctrl_check_ops
pinctrl: include <linux/bug.h> to prevent compile errors
pinctrl: fix compile error if not select PINMUX support
Merge tag 'tty-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull 3 tiny tty bugfixes from Greg Kroah-Hartman.
* tag 'tty-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
drivers/tty/amiserial.c: add missing tty_unlock
pch_uart: Fix dma channel unallocated issue
ARM: clps711x: serial driver hungs are a result of call disable_irq within ISR
Merge tag 'stable/for-linus-3.4-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen fixes from Konrad Rzeszutek Wilk:
- mechanism to work with misconfigured backends (where they are
advertised but in reality don't exist).
- two tiny compile warning fixes.
- proper error handling in gnttab_resume
- Not using VM_PFNMAP anymore to allow backends in the same domain.
* tag 'stable/for-linus-3.4-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
Revert "xen/p2m: m2p_find_override: use list_for_each_entry_safe"
xen/resume: Fix compile warnings.
xen/xenbus: Add quirk to deal with misconfigured backends.
xen/blkback: Fix warning error.
xen/p2m: m2p_find_override: use list_for_each_entry_safe
xen/gntdev: do not set VM_PFNMAP
xen/grant-table: add error-handling code on failure of gnttab_resume
It breaks reboot on at least one Thinkpad T43, as reported by Jörg Otte:
"On reboot it shuts down as normal.
The last lines displayed are:
>Unmounting temporary filesystems.. [OK]
>Deactivating swap... [OK]
>Unmounting local filesystems... [OK]
>Will now restart
> Restarting system
Then I hear it accessing the cd-drive, but then it's being stuck."
Jörg bisected the regression to this commit.
That commit fixes another machine (see
https://bugzilla.kernel.org/show_bug.cgi?id=11533
for details) that has a BIOS bug and doesn't support ACPI reset.
However, at least one of those other reporters no longer even has the
machine in question, and had a different workaround to begin with.
Besides, it clearly was a buggy BIOS. Let's not break the correct case
to fix that case.
Reported-and-bisected-by: Jörg Otte <jrg.otte@googlemail.com> Cc: linux-acpi@vger.kernel.org Cc: Len Brown <lenb@kernel.org> Cc: Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
memblock: memblock should be able to handle zero length operations
Commit 24aa07882b ("memblock, x86: Replace memblock_x86_reserve/
free_range() with generic ones") replaced x86 specific memblock
operations with the generic ones; unfortunately, it lost zero length
operation handling in the process making the kernel panic if somebody
tries to reserve zero length area.
There isn't much to be gained by being cranky to zero length operations
and panicking is almost the worst response. Drop the BUG_ON() in
memblock_reserve() and update memblock_add_region/isolate_range() so
that all zero length operations are handled as noops.
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pyll hwmon fixes from Guenter Roeck:
"Two patches: Fix build warning in ads1015 driver, and fix bogus power
values with current BIOSes in fam15h_power driver."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ads1015) Fix build warning
hwmon: fam15h_power: fix bogus values with current BIOSes
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Fixes for a few regressions of HD-audio, originated partly from 3.4
and partly 3.3.
The fixes for ThinkPad docking-station are for 3.3 kernels, thus they
are based on 3.3 then merged back to 3.4, so that they can be merged
to stable tree cleanly. The non-trivial merge conflicts are because
of this action.
In addition, a couple of trivial fixes for documentation and a long-
standing issue in the listing of built-in sound driver at boot time."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/conexant - Set up the missing docking-station pins
ALSA: hda/conexant - Don't set HP pin-control bit unconditionally
ALSA: workaround: change the timing of alsa_sound_last_init()
ALSA: hda/sigmatel - Fix inverted mute LED
ALSA: hda/realtek - Fix regression on Quanta/Gericom KN1
ALSA: fix core/vmaster.c kernel-doc warning
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
"Fix for one particular device (bluetooth Tivo Slide) and change of
'default y' -> 'default n' for CONFIG_HID_BATTERY_STRENGTH which I
overlooked in the initial merge of the battery support"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: default HID_BATTERY_STRENGTH to no
HID: tivo: fix support for bluetooth version of tivo Slide
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68k arch fixes from Greg Ungerer:
"This contains four fixes for 3.4. Two fix and clean up compilation
for the nommu 68x328 CPU targets. The other two fix the platform
definition and multi-function pin setup of the second eth interface
on the ColdFire 5275 SoC."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: make sure 2nd FEC eth interface pins are enabled on 5275 ColdFire
m68knommu: fix id number for second eth device on 5275 ColdFire
m68knommu: move and fix the 68VZ328 platform bootlogo.h
m68knommu: remove the unused bootlogo.h processing for 68EZ328 and 68VZ328
If we have another thread (very likely) touched the list, we
end up hitting a problem "that the next element is wrong because
we should be able to cope with that. The problem is that the
next->next pointer would be set LIST_POISON1. " (Stefano's
comment on the patch).
Reverting for now.
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Fixed too small hardcoded timeout values for usb_control_msg
in driver for SiliconLabs cp210x-based usb-to-serial adapters.
Replaced with USB_CTRL_GET_TIMEOUT/USB_CTRL_SET_TIMEOUT.
Merge branch 'for-3.4' of git://linux-nfs.org/~bfields/linux
Pull nfsd bugfixes from J. Bruce Fields:
"One bugfix, and one minor header fix from Jeff Layton while we're
here"
* 'for-3.4' of git://linux-nfs.org/~bfields/linux:
nfsd: include cld.h in the headers_install target
nfsd: don't fail unchecked creates of non-special files
linux/drivers/xen/manage.c: In function 'do_suspend':
linux/drivers/xen/manage.c:160:5: warning: 'si.cancelled' may be used uninitialized in this function
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"It's like a grab bag of one liners:
- core: fix page flip error path, reorder object teardown.
- usb: fix the drm_usb module license.
- i915: VT switch on SNB with non-native modes fix, and a regression
fix from 3.3.
- radeon: missing unreserve on SI, AGP/VRAM setup fix (fixes radeon on
IA64, but its a generic bug), an rn50 regression from 3.3, turn off
MSIs on rv515 (it loses rearms every so often)."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
nouveau: Set special lane map for the right chipset
drm/radeon: fix load detect on rn50 with hardcoded EDIDs.
drm: Releasing FBs before releasing GEM objects during drm_release
drm/nouveau/pm: don't read/write beyond end of stack buffer
drivers: gpu: drm: gma500: mdfld_dsi_output.h: Remove not unneeded include of version.h
radeon: fix r600/agp when vram is after AGP (v3)
drm: fix page_flip error handling
drm/radeon/kms: fix the regression of DVI connector check
drm/usb: fix module license on drm/usb layer.
drm/i915: Do not set "Enable Panel Fitter" on SNB pageflips
drm/i915: Hold mode_config lock whilst changing mode for lastclose()
drm/radeon/si: add missing radeon_bo_unreserve in si_rlc_init() v2
drm/radeon: disable MSI on RV515
drm/i915: don't clobber the special upscaling lvds timings
linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_crop':
linux-2.6/drivers/media/video/mt9m032.c:337: error: implicit declaration of function 'v4l2_subdev_get_try_crop'
linux-2.6/drivers/media/video/mt9m032.c:337: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_format':
linux-2.6/drivers/media/video/mt9m032.c:359: error: implicit declaration of function 'v4l2_subdev_get_try_format'
linux-2.6/drivers/media/video/mt9m032.c:359: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_probe':
linux-2.6/drivers/media/video/mt9m032.c:767: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c:826: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_remove':
linux-2.6/drivers/media/video/mt9m032.c:842: error: 'struct v4l2_subdev' has no member named 'entity'
make[4]: *** [drivers/media/video/mt9m032.o] Error 1
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: lock slots_lock around device assignment
KVM: VMX: Fix kvm_set_shared_msr() called in preemptible context
KVM: unmap pages from the iommu when slots are removed
KVM: PMU emulation: GLOBAL_CTRL MSR should be enabled on reset
xen/xenbus: Add quirk to deal with misconfigured backends.
A rather annoying and common case is when booting a PVonHVM guest
and exposing the PV KBD and PV VFB - as broken toolstacks don't
always initialize the backends correctly.
Normally The HVM guest is using the VGA driver and the emulated
keyboard for this (though upstream version of QEMU implements
PV KBD, but still uses a VGA driver). We provide a very basic
two-stage wait mechanism - where we wait for 30 seconds for all
devices, and then for 270 for all them except the two mentioned.
That allows us to wait for the essential devices, like network
or disk for the full 6 minutes.
To trigger this, put this in your guest config:
vfb = [ 'vnc=1, vnclisten=0.0.0.0 ,vncunused=1']
instead of this:
vnc=1
vnclisten="0.0.0.0"
CC: stable@kernel.org Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
[v3: Split delay in non-essential (30 seconds) and essential
devices per Ian and Stefano suggestion]
[v4: Added comments per Stefano suggestion] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Henrik Rydberg [Thu, 12 Apr 2012 22:37:00 +0000 (00:37 +0200)]
nouveau: Set special lane map for the right chipset
The refactoring of the nv50 logic, introduced in 8663bc7c, modified the
test for the special lane map used on some Apple computers with Nvidia
chipsets. The tested MBA3,1 would still boot, but resume from suspend
stopped working. This patch restores the old test, which fixes the problem.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Acked-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Merge fixes for Thinkpad docking-station regressions for 3.3 kernels
back to 3.4. These were committed in that branch to make the stable
merging easier.
ALSA: hda/conexant - Set up the missing docking-station pins
ThinkPad 410,420,510,520 and X201 with cx50585 & co chips have the
docking-station ports, but BIOS doesn't initialize for these pins.
Thus, like the former X200, we need to set up the pins manually in the
driver.
The odd part is that the same PCI SSID is used for X200 and T400, thus
we need to prepare individual fixup tables for cx5051 and others.
Dave Airlie [Thu, 19 Apr 2012 14:42:58 +0000 (15:42 +0100)]
drm/radeon: fix load detect on rn50 with hardcoded EDIDs.
When the force changes went in back in 3.3.0, we ended up returning
disconnected in the !force case, and the connected in when forced,
as it hit the hardcoded check.
Fix it so all exits go via the hardcoded check and stop spurious
modesets on platforms with hardcoded EDIDs.
Reported-by: Evan McNabb (Red Hat) Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
drm: Releasing FBs before releasing GEM objects during drm_release
During DRM release, all the FBs and gem objects are released. If
a gem object is being used as a FB and set to a crtc, it must not
be freed before releasing the framebuffer first.
If FBs are released first, the crtc using the FB is disabled first
so now the GEM object can be freed safely. The CRTC will be enabled
again when the driver restores fbdev mode.
Signed-off-by: Prathyush K <prathyush.k@samsung.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jim Meyering [Tue, 17 Apr 2012 19:27:54 +0000 (21:27 +0200)]
drm/nouveau/pm: don't read/write beyond end of stack buffer
NUL-terminate after strncpy.
If the parameter "profile" has length 16 or more, then strncpy
leaves "string" with no NUL terminator, so the following search
for '\n' may read beyond the end of that 16-byte buffer.
If it finds a newline there, then it will also write beyond the
end of that stack buffer.
Signed-off-by: Jim Meyering <meyering@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers: gpu: drm: gma500: mdfld_dsi_output.h: Remove not unneeded include of version.h
The output of "make versioncheck" points a incorrect include of
version.h in the drivers/gpu/drm/gma500/mdfld_dsi_output.h:
drivers/gpu/drm/gma500/mdfld_dsi_output.h: 32 linux/version.h not needed.
If we take a look in the file, we can agree to remove it.
Cc: David Airlie <airlied@linux.ie> Cc: <dri-devel@lists.freedesktop.org> Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 19 Apr 2012 13:13:52 +0000 (14:13 +0100)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Do not set "Enable Panel Fitter" on SNB pageflips
drm/i915: Hold mode_config lock whilst changing mode for lastclose()
drm/i915: don't clobber the special upscaling lvds timings
drm/radeon/kms: fix the regression of DVI connector check
The check of the encoder type in the commit [e00e8b5e: drm/radeon/kms:
fix analog load detection on DVI-I connectors] is obviously wrong, and
it's the culprit of the regression on my workstation with DVI-analog
connection resulting in the blank output.
Fixed the typo now.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Cc: <stable@vger.kernel.org> Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 4f5ca836b "HID: hid-input: add support for HID devices reporting
Battery Strength" added the CONFIG_HID_BATTERY_STRENGTH option to report
the battery strength of HID devices. The commit log explicitly mentions
it not working properly with recent userspace, but it is default y
anyway. This is rather odd, and actually causes problems on real
systems.
This works around Fedora bug
https://bugzilla.redhat.com/show_bug.cgi?id=806295