Use remove_pagetable() and friends for radix vmemmap removal.
We do not require the special-case handling of vmemmap done in the x86
versions of these functions. This is because vmemmap_free() has already
freed the mapped pages, and calls us with an aligned address range.
So, add a few failsafe WARNs, but otherwise the code to remove physical
mappings is already sufficient for vmemmap.
Reza Arbab [Mon, 16 Jan 2017 19:07:45 +0000 (13:07 -0600)]
powerpc/mm: add radix__remove_section_mapping()
Tear down and free the four-level page tables of physical mappings
during memory hotremove.
Borrow the basic structure of remove_pagetable() and friends from the
identically-named x86 functions. Reduce the frequency of tlb flushes and
page_table_lock spinlocks by only doing them in the outermost function.
There was some question as to whether the locking is needed at all.
Leave it for now, but we could consider dropping it.
Memory must be offline to be removed, thus not in use. So there
shouldn't be the sort of concurrent page walking activity here that
might prompt us to use RCU.
Signed-off-by: Reza Arbab <arbab@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reza Arbab [Mon, 16 Jan 2017 19:07:43 +0000 (13:07 -0600)]
powerpc/mm: refactor radix physical page mapping
Move the page mapping code in radix_init_pgtable() into a separate
function that will also be used for memory hotplug.
The current goto loop progressively decreases its mapping size as it
covers the tail of a range whose end is unaligned. Change this to a for
loop which can do the same for both ends of the range.
Signed-off-by: Reza Arbab <arbab@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/powernv: Add support for direct mapped LPC on POWER9
Use the new non-PCI ISA bridge support to expose the POWER9
LPC bus as direct mapped via the ISA IO port range. This
enables direct access via drivers such as 8250
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Documentation:powerpc: Add device-tree bindings for power-mgt
Document the device-tree bindings defining the the properties under
the @power-mgt node in the device tree that describe the idle states
for Linux running on baremetal POWER servers.
These bindings are documented separately instead of using the the
common idle state bindings since the idle-states on POWER servers
are exposed as property arrays where as the common idle state bindings
expect idle-states to be described as nodes.
Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powernv: Pass PSSCR value and mask to power9_idle_stop
The power9_idle_stop method currently takes only the requested stop
level as a parameter and picks up the rest of the PSSCR bits from a
hand-coded macro. This is not a very flexible design, especially when
the firmware has the capability to communicate the psscr value and the
mask associated with a particular stop state via device tree.
This patch modifies the power9_idle_stop API to take as parameters the
PSSCR value and the PSSCR mask corresponding to the stop state that
needs to be set. These PSSCR value and mask are respectively obtained
by parsing the "ibm,cpu-idle-state-psscr" and
"ibm,cpu-idle-state-psscr-mask" fields from the device tree.
In addition to this, the patch adds support for handling stop states
for which ESL and EC bits in the PSSCR are zero. As per the
architecture, a wakeup from these stop states resumes execution from
the subsequent instruction as opposed to waking up at the System
Vector.
The older firmware sets only the Requested Level (RL) field in the
psscr and psscr-mask exposed in the device tree. For older firmware
where psscr-mask=0xf, this patch will set the default sane values that
the set for for remaining PSSCR fields (i.e PSLL, MTL, ESL, EC, and
TR). For the new firmware, the patch will validate that the invariants
required by the ISA for the psscr values are maintained by the
firmware.
This skiboot patch that exports fully populated PSSCR values and the
mask for all the stop states can be found here:
https://lists.ozlabs.org/pipermail/skiboot/2016-September/004869.html
[Optimize the number of instructions before entering STOP with
ESL=EC=0, validate the PSSCR values provided by the firimware
maintains the invariants required as per the ISA suggested by Balbir
Singh]
Acked-by: Balbir Singh <bsingharora@gmail.com> Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
cpuidle:powernv: Add helper function to populate powernv idle states.
In the current code for powernv_add_idle_states, there is a lot of code
duplication while initializing an idle state in powernv_states table.
Add an inline helper function to populate the powernv_states[] table
for a given idle state. Invoke this for populating the "Nap",
"Fastsleep" and the stop states in powernv_add_idle_states.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com> Acked-by: Balbir Singh <bsingharora@gmail.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powernv:stop: Rename pnv_arch300_idle_init to pnv_power9_idle_init
Balbir pointed out that the name of the function pnv_arch300_idle_init
was inconsistent with the names of the variables and functions
pertaining to POWER9 features in book3s_idle.S.
This patch renames pnv_arch300_idle_init to pnv_power9_idle_init.
This patch does not change any behaviour.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently all the low-power idle states are expected to wake up
at reset vector 0x100. Which is why the macro IDLE_STATE_ENTER_SEQ
that puts the CPU to an idle state and never returns.
On ISA v3.0, when the ESL and EC bits in the PSSCR are zero, the CPU
is expected to wake up at the next instruction of the idle
instruction.
This patch adds a new macro named IDLE_STATE_ENTER_SEQ_NORET for the
no-return variant and reuses the name IDLE_STATE_ENTER_SEQ
for a variant that allows resuming operation at the instruction next
to the idle-instruction.
Acked-by: Balbir Singh <bsingharora@gmail.com> Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Alistair Popple [Tue, 10 Jan 2017 04:41:44 +0000 (15:41 +1100)]
powerpc/powernv: Use OPAL call for TCE kill on NVLink2
Add detection of NPU2 PHBs. NPU2/NVLink2 has a different register
layout for the TCE kill register therefore TCE invalidation should be
done via the OPAL call rather than using the register directly as it
is for PHB3 and NVLink1. This changes TCE invalidation to use the OPAL
call in the case of a NPU2 PHB model.
Signed-off-by: Alistair Popple <alistair@popple.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Alistair Popple [Wed, 14 Dec 2016 02:36:51 +0000 (13:36 +1100)]
powerpc/powernv: Initialise nest mmu
POWER9 contains an off core mmu called the nest mmu (NMMU). This is
used by other hardware units on the chip to translate virtual
addresses into real addresses. The unit attempting an address
translation provides the majority of the context required for the
translation request except for the base address of the partition table
(ie. the PTCR) which needs to be programmed into the NMMU.
This patch adds a call to OPAL to set the PTCR for the nest mmu in
opal_init().
Signed-off-by: Alistair Popple <alistair@popple.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reza Arbab [Wed, 16 Nov 2016 16:45:03 +0000 (10:45 -0600)]
powerpc/mm: Allow memory hotplug into an offline node
Relax the check preventing us from hotplugging into an offline node.
This limitation was added in commit 482ec7c403d2 ("[PATCH] powerpc numa:
Support sparse online node map") to prevent adding resources to an
uninitialized node.
These days, there is no harm in doing so. The addition will actually
cause the node to be initialized and onlined; add_memory_resource()
calls hotadd_new_pgdat() (if necessary) and node_set_online().
Signed-off-by: Reza Arbab <arbab@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are chances that multiple CPUs can call crash_fadump() simultaneously
and would start duplicating same info to vmcoreinfo ELF note section. This
causes makedumpfile to fail during kdump capture. One example is,
triggering dumprestart from HMC which sends system reset to all the CPUs at
once.
makedumpfile --dump-dmesg /proc/vmcore
read_vmcoreinfo_basic_info: Invalid data in /tmp/vmcoreinfoyjgxlL: CRASHTIME=1475605971CRASHTIME=1475605971CRASHTIME=1475605971CRASHTIME=1475605971CRASHTIME=1475605971CRASHTIME=1475605971CRASHTIME=1475605971CRASHTIME=1475605971
makedumpfile Failed.
Running makedumpfile --dump-dmesg /proc/vmcore failed (1).
powerpc/mm/hash: Properly mask the ESID bits when building proto VSID
The proto VSID is built using both the MMU context id and effective
segment ID (ESID). We should not have overlapping bits between those.
That could result in us having a VSID collision. With the current code
we missed masking the top bits of the ESID. This implies for kernel
address we ended up using the top 4 bits of the ESID as part of the
proto VSID, which is wrong.
The current code use the top 4 context values (0x7fffc - 0x7ffff) for
the kernel. With those context IDs used for the kernel, we don't run
into VSID collisions because we get the same proto VSID irrespective of
whether we mask the ESID bits or not. eg:
Naveen N. Rao [Fri, 13 Jan 2017 17:10:01 +0000 (22:40 +0530)]
powerpc/bpf: Flush the entire JIT buffer
With bpf_jit_binary_alloc(), we allocate at a page granularity and fill
the rest of the space with illegal instructions to mitigate BPF spraying
attacks, while having the actual JIT'ed BPF program at a random location
within the allocated space. Under this scenario, it would be better to
flush the entire allocated buffer rather than just the part containing
the actual program. We already flush the buffer from start to the end of
the BPF program. Extend this to include the illegal instructions after
the BPF program.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Borkmann [Fri, 13 Jan 2017 17:10:00 +0000 (22:40 +0530)]
powerpc/bpf: Remove redundant check for non-null image
We have a check earlier to ensure we don't proceed if image is NULL. As
such, the redundant check can be removed.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
[Added similar changes for classic BPF JIT] Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
cxl: Prevent read/write to AFU config space while AFU not configured
During EEH recovery, we deconfigure all AFUs whilst leaving the
corresponding vPHB and virtual PCI device in place.
If something attempts to interact with the AFU's PCI config space (e.g.
running lspci) after the AFU has been deconfigured and before it's
reconfigured, cxl_pcie_{read,write}_config() will read invalid values from
the deconfigured struct cxl_afu and proceed to Oops when they try to
dereference pointers that have been set to NULL during deconfiguration.
Add a rwsem to struct cxl_afu so we can prevent interaction with config
space while the AFU is deconfigured.
Vaibhav Jain [Wed, 4 Jan 2017 06:18:52 +0000 (11:48 +0530)]
cxl: Force psl data-cache flush during device shutdown
This change adds a force psl data cache flush during device shutdown
callback. This should reduce a possibility of psl holding a dirty
cache line while the CAPP is being reinitialized, which may result in
a UE [load/store] machine check error.
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com> Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Markus Elfring [Sat, 21 Jan 2017 15:10:50 +0000 (16:10 +0100)]
powerpc/mm: Return directly after a failed __copy_from_user() in sys_subpage_prot()
This function already has multiple exit points, so there's no harm
adding another. Although it looks odd to return directly in a function
which takes a lock, we've actually just dropped the mmap_sem in this
code, so there's really no reason to go via a label. And it means we can
drop the unhelpfully named out2 label.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[mpe: Rewrite change log] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Markus Elfring [Sat, 21 Jan 2017 14:30:15 +0000 (15:30 +0100)]
powerpc/sstep: Return directly after a failed address_ok() in emulate_step()
Setting err and going to ldst_done just returns 0, without using err, so
just return 0 directly. We already do that for other call sites in this
function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[mpe: Rewrite change log] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Mon, 23 Jan 2017 22:49:54 +0000 (09:49 +1100)]
powerpc/kernel: Fix unbalanced refcount on RTAS device node
The RTAS device-tree node's refcount has been increased by one in
the function call of_find_node_by_name(), but it's missed to be
decreased by one in the error path. It leads to unbalanced refcount
on RTAS device-tree node.
This fixes above issue by decreasing RTAS device-tree node's refcount
in error path.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Paul Mackerras [Thu, 3 Nov 2016 05:15:42 +0000 (16:15 +1100)]
powerpc/64: Use optimized checksum routines on little-endian
Currently we have optimized hand-coded assembly checksum routines for
big-endian 64-bit systems, but for little-endian we use the generic C
routines. This modifies the optimized routines to work for
little-endian. With this, we no longer need to enable
CONFIG_GENERIC_CSUM. This also fixes a couple of comments in
checksum_64.S so they accurately reflect what the associated instruction
does.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
[mpe: Use the more common __BIG_ENDIAN__] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Paul Mackerras [Thu, 3 Nov 2016 05:10:55 +0000 (16:10 +1100)]
powerpc/64: Fix checksum folding in csum_tcpudp_nofold and ip_fast_csum_nofold
These functions compute an IP checksum by computing a 64-bit sum and
folding it to 32 bits (the "nofold" in their names refers to folding
down to 16 bits). However, doing (u32) (s + (s >> 32)) is not
sufficient to fold a 64-bit sum to 32 bits correctly. The addition
can produce a carry out from bit 31, which needs to be added in to
the sum to produce the correct result.
To fix this, we copy the from64to32() function from lib/checksum.c
and use that.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Joel Stanley [Fri, 13 Jan 2017 03:53:49 +0000 (14:23 +1030)]
powerpc/powernv: Report size of OPAL memcons log
The OPAL memory console is reported to be size zero, as we do not
initialise the struct attr with any size information due to the size
being variable. This leads users to think that the console is empty.
Instead report the maximum size.
Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm/4k: don't allocate larger pmd page table for 4k
We now support THP with both 64k and 4K page size configuration
for radix. (hash only support THP with 64K page size). Hence we
will have CONFIG_TRANSPARENT_HUGEPAGE enabled for both PPC_64K
and PPC_4K config. Since we only need large pmd page table
with hash configuration (to store the slot information
in the second half of the table) restrict the large pmd page table
to THP and 64K configs.
Linus Torvalds [Sun, 22 Jan 2017 20:47:48 +0000 (12:47 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Thomas Gleixner:
"Restore the retrigger callbacks in the IO APIC irq chips. That
addresses a long standing regression which got introduced with the
rewrite of the x86 irq subsystem two years ago and went unnoticed so
far"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ioapic: Restore IO-APIC irq_chip retrigger callback
Linus Torvalds [Sun, 22 Jan 2017 20:40:09 +0000 (12:40 -0800)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio/vhost fixes from Michael Tsirkin:
"Random fixes and cleanups that accumulated over the time"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio/s390: virtio: constify virtio_config_ops structures
virtio/s390: add missing \n to end of dev_err message
virtio/s390: support READ_STATUS command for virtio-ccw
tools/virtio/ringtest: tweaks for s390
tools/virtio/ringtest: fix run-on-all.sh for offline cpus
virtio_console: fix a crash in config_work_handler
vhost/scsi: silence uninitialized variable warning
vhost: scsi: constify target_core_fabric_ops structures
Linus Torvalds [Sun, 22 Jan 2017 20:36:47 +0000 (12:36 -0800)]
Merge branch 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management fixes from Zhang Rui:
- fix a regression that thermal zone dynamically allocated sysfs
attributes are freed before they're removed, which is introduced in
4.10-rc1 (Jacob von Chorus)
- fix a boot warning because deprecated hwmon API is used (Fabio
Estevam)
- a couple of fixes for rockchip thermal driver (Brian Norris, Caesar
Wang)
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: rockchip: fixes the conversion table
thermal: core: move tz->device.groups cleanup to thermal_release
thermal: thermal_hwmon: Convert to hwmon_device_register_with_info()
thermal: rockchip: handle set_trips without the trip points
thermal: rockchip: optimize the conversion table
thermal: rockchip: fixes invalid temperature case
thermal: rockchip: don't pass table structs by value
thermal: rockchip: improve conversion error messages
Linus Torvalds [Sun, 22 Jan 2017 03:01:06 +0000 (19:01 -0800)]
Merge tag 'usb-4.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a few small USB fixes for 4.10-rc5.
Most of these are gadget/dwc2 fixes for reported issues, all of these
have been in linux-next for a while. The last one is a single xhci
WARN_ON removal to handle an issue that the dwc3 driver is hitting in
the 4.10-rc tree. The warning is harmless and needs to be removed, and
a "real" fix that is more complex will show up in 4.11-rc1 for this
device.
That last patch hasn't been in linux-next yet due to the weekend
timing, but it's a "simple" WARN_ON() removal so what could go wrong?
:)"
Famous last words.
* tag 'usb-4.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: remove WARN_ON if dma mask is not set for platform devices
usb: dwc2: host: fix Wmaybe-uninitialized warning
usb: dwc2: gadget: Fix GUSBCFG.USBTRDTIM value
usb: gadget: udc: atmel: remove memory leak
usb: dwc3: exynos fix axius clock error path to do cleanup
usb: dwc2: Avoid suspending if we're in gadget mode
usb: dwc2: use u32 for DT binding parameters
usb: gadget: f_fs: Fix iterations on endpoints.
usb: dwc2: gadget: Fix DMA memory freeing
usb: gadget: composite: Fix function used to free memory
Linus Torvalds [Sun, 22 Jan 2017 02:53:06 +0000 (18:53 -0800)]
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"Two fixes:
- a regression fix for the multiple-pmem-namespace-per-region support
added in 4.9. Even if an existing environment is not using that
feature the act of creating and a destroying a single namespace
with the ndctl utility will lead to the proliferation of extra
unwanted namespace devices.
- a fix for the error code returned from the pmem driver when the
memcpy_mcsafe() routine returns -EFAULT. Btrfs seems to be the only
block I/O consumer that tries to parse the meaning of the error
code when it is non-zero.
Neither of these fixes are critical, the namespace leak is awkward in
that it can cause device naming to change and complicates debugging
namespace initialization issues. The error code fix is included out of
caution for what other consumers might be expecting -EIO for block I/O
errors"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm, namespace: fix pmem namespace leak, delete when size set to zero
pmem: return EIO on read_pmem() failure
Linus Torvalds [Sun, 22 Jan 2017 02:46:45 +0000 (18:46 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One fix for Samsung Exynos524x SoCs where recent IOMMU patches have
caused some of these clocks to turn off when they were always left on
before"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk/samsung: exynos542x: mark some clocks as critical
Linus Torvalds [Sun, 22 Jan 2017 02:07:40 +0000 (18:07 -0800)]
Merge tag 'arc-4.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- more intc updates [Yuriv]
- fix module build when unwinder is turned off
- IO Coherency Programming model updates
- other miscellaneous
* tag 'arc-4.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Revert "ARC: mm: IOC: Don't enable IOC by default"
ARC: mm: split arc_cache_init to allow __init reaping of bulk
ARCv2: IOC: Use actual memory size to setup aperture size
ARCv2: IOC: Adhere to progamming model guidelines to avoid DMA corruption
ARCv2: IOC: refactor the IOC and SLC operations into own functions
ARC: module: Fix !CONFIG_ARC_DW2_UNWIND builds
ARCv2: save r30 on kernel entry as gcc uses it for code-gen
ARCv2: IRQ: Call entry/exit functions for chained handlers in MCIP
ARC: IRQ: Use hwirq instead of virq in mask/unmask
ARC: mmu: clarify the MMUv3 programming model
Linus Torvalds [Sun, 22 Jan 2017 01:58:45 +0000 (17:58 -0800)]
Merge tag 'powerpc-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Two fixes for fallout from the hugetlb changes we merged this cycle.
Ten other fixes, four only affect Power9, and the rest are a bit of a
mixture though nothing terrible.
Thanks to: Aneesh Kumar K.V, Anton Blanchard, Benjamin Herrenschmidt,
Dave Martin, Gavin Shan, Madhavan Srinivasan, Nicholas Piggin, Reza
Arbab"
* tag 'powerpc-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Ignore reserved field in DCSR and PVR reads and writes
powerpc/ptrace: Preserve previous TM fprs/vsrs on short regset write
powerpc/ptrace: Preserve previous fprs/vsrs on short regset write
powerpc/perf: Use MSR to report privilege level on P9 DD1
selftest/powerpc: Wrong PMC initialized in pmc56_overflow test
powerpc/eeh: Enable IO path on permanent error
powerpc/perf: Fix PM_BRU_CMPL event code for power9
powerpc/mm: Fix little-endian 4K hugetlb
powerpc/mm/hugetlb: Don't panic when we don't find the default huge page size
powerpc: Fix pgtable pmd cache init
powerpc/icp-opal: Fix missing KVM case and harden replay
powerpc/mm: Fix memory hotplug BUG() on radix
Linus Torvalds [Fri, 20 Jan 2017 22:19:34 +0000 (14:19 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM:
- Fix for timer setup on VHE machines
- Drop spurious warning when the timer races against the vcpu running
again
- Prevent a vgic deadlock when the initialization fails (for stable)
s390:
- Fix a kernel memory exposure (for stable)
x86:
- Fix exception injection when hypercall instruction cannot be
patched"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: s390: do not expose random data via facility bitmap
KVM: x86: fix fixing of hypercalls
KVM: arm/arm64: vgic: Fix deadlock on error handling
KVM: arm64: Access CNTHCTL_EL2 bit fields correctly on VHE systems
KVM: arm/arm64: Fix occasional warning from the timer work function
Linus Torvalds [Fri, 20 Jan 2017 22:17:04 +0000 (14:17 -0800)]
Merge branch 'scsi-target-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bvanassche/linux
Pull SCSI target fixes from Bart Van Assche:
- two small fixes for the ibmvscsis driver
- ten patches with bug fixes for the target mode of the qla2xxx driver
- four patches that avoid that the "sparse" and "smatch" static
analyzer tools report false positives for the qla2xxx code base
* 'scsi-target-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bvanassche/linux:
qla2xxx: Disable out-of-order processing by default in firmware
qla2xxx: Fix erroneous invalid handle message
qla2xxx: Reduce exess wait during chip reset
qla2xxx: Terminate exchange if corrupted
qla2xxx: Fix crash due to null pointer access
qla2xxx: Collect additional information to debug fw dump
qla2xxx: Reset reserved field in firmware options to 0
qla2xxx: Set tcm_qla2xxx version to automatically track qla2xxx version
qla2xxx: Include ATIO queue in firmware dump when in target mode
qla2xxx: Fix wrong IOCB type assumption
qla2xxx: Avoid that building with W=1 triggers complaints about set-but-not-used variables
qla2xxx: Move two arrays from header files to .c files
qla2xxx: Declare an array with file scope static
qla2xxx: Fix indentation
ibmvscsis: Fix sleeping in interrupt context
ibmvscsis: Fix max transfer length
Linus Torvalds [Fri, 20 Jan 2017 20:28:02 +0000 (12:28 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Just two small fixes for this -rc.
One is just killing an unused variable from Keith, but the other
fixes a performance regression for nbd in this series, where we
inadvertently flipped when we set MSG_MORE when outputting data"
* 'for-linus' of git://git.kernel.dk/linux-block:
nbd: only set MSG_MORE when we have more to send
blk-mq: Remove unused variable
Linus Torvalds [Fri, 20 Jan 2017 20:25:11 +0000 (12:25 -0800)]
Merge tag 'spi-fix-v4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"The usual small smattering of driver specific fixes. A few bits that
stand out here:
- the R-Car patches adding fallbacks are just adding new compatible
strings to the driver so that device trees are written in a more
robustly future proof fashion, this isn't strictly a fix but it's
just new IDs and it's better to get it into mainline sooner to
improve the ABI
- the DesignWare "switch to new API part 2" patch is actually a
misleadingly titled fix for a bit that got missed in the original
conversion"
* tag 'spi-fix-v4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: davinci: use dma_mapping_error()
spi: spi-axi: Free resources on error path
spi: pxa2xx: add missed break
spi: dw-mid: switch to new dmaengine_terminate_* API (part 2)
spi: dw: Make debugfs name unique between instances
spi: sh-msiof: Do not use C++ style comment
spi: armada-3700: Set mode bits correctly
spi: armada-3700: fix unsigned compare than zero on irq
spi: sh-msiof: Add R-Car Gen 2 and 3 fallback bindings
spi: SPI_FSL_DSPI should depend on HAS_DMA
Linus Torvalds [Fri, 20 Jan 2017 20:15:48 +0000 (12:15 -0800)]
Merge tag 'ceph-for-4.10-rc5' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"Three filesystem endianness fixes (one goes back to the 2.6 era, all
marked for stable) and two fixups for this merge window's patches"
* tag 'ceph-for-4.10-rc5' of git://github.com/ceph/ceph-client:
ceph: fix bad endianness handling in parse_reply_info_extra
ceph: fix endianness bug in frag_tree_split_cmp
ceph: fix endianness of getattr mask in ceph_d_revalidate
libceph: make sure ceph_aes_crypt() IV is aligned
ceph: fix ceph_get_caps() interruption
Linus Torvalds [Fri, 20 Jan 2017 19:56:29 +0000 (11:56 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse fixes from Miklos Szeredi:
"Fix two regressions, one introduced in 4.9 and a less recent one in
4.2"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix time_to_jiffies nsec sanity check
fuse: clear FR_PENDING flag when moving requests out of pending queue
Linus Torvalds [Fri, 20 Jan 2017 19:47:18 +0000 (11:47 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of 12 fixes including the mpt3sas one that was causing
hangs on ATA passthrough.
The others are a couple of zoned block device fixes, a SAS device
detection bug which lead to SATA drives not being matched to bays, two
qla2xxx MSI fixes, a qla2xxx req for rsp confusion caused by cut and
paste, and a few other minor fixes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mpt3sas: fix hang on ata passthrough commands
scsi: lpfc: Set elsiocb contexts to NULL after freeing it
scsi: sd: Ignore zoned field for host-managed devices
scsi: sd: Fix wrong DPOFUA disable in sd_read_cache_type
scsi: bfa: fix wrongly initialized variable in bfad_im_bsg_els_ct_request()
scsi: ses: Fix SAS device detection in enclosure
scsi: libfc: Fix variable name in fc_set_wwpn
scsi: lpfc: avoid double free of resource identifiers
scsi: qla2xxx: remove irq_affinity_notifier
scsi: qla2xxx: fix MSI-X vector affinity
scsi: qla2xxx: Fix apparent cut-n-paste error.
scsi: qla2xxx: Get mutex lock before checking optrom_state
Linus Torvalds [Fri, 20 Jan 2017 19:44:47 +0000 (11:44 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- avoid potential stack information leak via the ptrace ABI caused by
uninitialised variables
- SWIOTLB DMA API fall-back allocation fix when the SWIOTLB buffer is
not initialised (all RAM is suitable for 32-bit DMA masks)
- fix the bad_mode function returning for unhandled exceptions coming
from user space
- fix name clash in __page_to_voff()
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: avoid returning from bad_mode
arm64/ptrace: Reject attempts to set incomplete hardware breakpoint fields
arm64/ptrace: Avoid uninitialised struct padding in fpr_set()
arm64/ptrace: Preserve previous registers for short regset write
arm64/ptrace: Preserve previous registers for short regset write
arm64/ptrace: Preserve previous registers for short regset write
arm64: mm: avoid name clash in __page_to_voff()
arm64: Fix swiotlb fallback allocation
KVM: s390: do not expose random data via facility bitmap
kvm_s390_get_machine() populates the facility bitmap by copying bytes
from the host results that are stored in a 256 byte array in the prefix
page. The KVM code does use the size of the target buffer (2k), thus
copying and exposing unrelated kernel memory (mostly machine check
related logout data).
Let's use the size of the source buffer instead. This is ok, as the
target buffer will always be greater or equal than the source buffer as
the KVM internal buffers (and thus S390_ARCH_FAC_LIST_SIZE_BYTE) cover
the maximum possible size that is allowed by STFLE, which is 256
doublewords. All structures are zero allocated so we can leave bytes
256-2047 unchanged.
Add a similar fix for kvm_arch_init_vm().
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
[found with smatch] Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> CC: stable@vger.kernel.org Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Mathias Nyman [Fri, 20 Jan 2017 13:38:24 +0000 (15:38 +0200)]
xhci: remove WARN_ON if dma mask is not set for platform devices
The warn on is a bit too much, we will anyway set the dma mask if not set
previously.
The main reason for this fix is that 4.10-rc1 has a dwc3 change that
pass a parent sysdev dev pointer instead of setting the dma mask of
its xhci platform device. xhci platform driver can then get more
attributes from the sysdev than just the dma mask.
The usb core and xhci changes are not yet in 4.10, and a fix like
this was preferred instead of taking those big changes this late in
the rc-cycle.
Anton Blanchard [Thu, 19 Jan 2017 03:19:10 +0000 (14:19 +1100)]
powerpc: Ignore reserved field in DCSR and PVR reads and writes
IBM bit 31 (for the rest of us - bit 0) is a reserved field in the
instruction definition of mtspr and mfspr. Hardware is encouraged to
(and does) ignore it.
As a result, if userspace executes an mtspr DSCR with the reserved bit
set, we get a DSCR facility unavailable exception. The kernel fails to
match against the expected value/mask, and we silently return to
userspace to try and re-execute the same mtspr DSCR instruction. We
loop forever until the process is killed.
We should do something here, and it seems mirroring what hardware does
is the better option vs killing the process. While here, relax the
matching of mfspr PVR too.
Cc: stable@vger.kernel.org Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Dave Martin [Thu, 5 Jan 2017 16:50:57 +0000 (16:50 +0000)]
powerpc/ptrace: Preserve previous TM fprs/vsrs on short regset write
Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET
to fill all the check pointed registers, the thread's old check pointed
registers are preserved.
Fixes: 9d3918f7c0e5 ("powerpc/ptrace: Enable support for NT_PPC_CVSX") Fixes: 19cbcbf75a0c ("powerpc/ptrace: Enable support for NT_PPC_CFPR") Cc: stable@vger.kernel.org # v4.8+ Signed-off-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Dave Martin [Thu, 5 Jan 2017 16:50:57 +0000 (16:50 +0000)]
powerpc/ptrace: Preserve previous fprs/vsrs on short regset write
Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET
to fill all the registers, the thread's old registers are preserved.
Fixes: c6e6771b87d4 ("powerpc: Introduce VSX thread_struct and CONFIG_VSX") Cc: stable@vger.kernel.org # v2.6.27+ Signed-off-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Linus Torvalds [Fri, 20 Jan 2017 00:40:03 +0000 (16:40 -0800)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We've been sitting on fixes for a while, and they keep trickling in at
a low rate. Nothing in here comes across as particularly scary or
noteworthy, for the most part it's a large collection of small DT
tweaks"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (24 commits)
ARM: dts: da850-evm: fix read access to SPI flash
ARM: dts: omap3: Fix Card Detect and Write Protect on Logic PD SOM-LV
ARM64: dts: meson-gxbb-odroidc2: Disable SCPI DVFS
ARM: dts: OMAP5 / DRA7: indicate that SATA port 0 is available.
ARM: dts: NSP: Fix DT ranges error
ARM: multi_v7_defconfig: set bcm47xx watchdog
ARM: multi_v7_defconfig: fix config typo
ARM: dts: dra72-evm-revc: fix typo in ethernet-phy node
soc: ti: wkup_m3_ipc: Fix error return code in wkup_m3_ipc_probe()
ARM: ux500: fix prcmu_is_cpu_in_wfi() calculation
ARM: dts: sunxi: Change node name for pwrseq pin on Olinuxino-lime2-emmc
ARM: dts: sun8i: Support DTB build for NanoPi M1
ARM: dts: sun6i: hummingbird: Enable display engine again
ARM: dts: sun6i: Disable display pipeline by default
ARM, ARM64: dts: drop "arm,amba-bus" in favor of "simple-bus" part 3
ARM: dts: imx6qdl-nitrogen6_som2: fix sgtl5000 pinctrl init
ARM: dts: imx6qdl-nitrogen6_max: fix sgtl5000 pinctrl init
ARM: OMAP1: DMA: Correct the number of logical channels
ARM: dts: am335x-icev2: Remove the duplicated pinmux setting
ARM: OMAP2+: Fix WL1283 Bluetooth Baud Rate
...
Linus Torvalds [Fri, 20 Jan 2017 00:33:00 +0000 (16:33 -0800)]
Merge tag 'xfs-for-linux-4.10-rc5-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"I have a few more patches this week -- one to make the behavior of a
quota id ioctl consistent with the other filesystems, and the rest
improve validation of i_mode & i_size values coming into xfs so that
we don't read off the ends of arrays or crash when handed garbage disk
data.
Summary:
- inode i_mode sanitization
- prevent overflows in getnextquota
- minor build fixes"
* tag 'xfs-for-linux-4.10-rc5-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix xfs_mode_to_ftype() prototype
xfs: don't wrap ID in xfs_dq_get_next_id
xfs: sanity check inode di_mode
xfs: sanity check inode mode when creating new dentry
xfs: replace xfs_mode_to_ftype table with switch statement
xfs: add missing include dependencies to xfs_dir2.h
xfs: sanity check directory inode di_size
xfs: make the ASSERT() condition likely
Fabien Parent [Tue, 17 Jan 2017 12:57:42 +0000 (13:57 +0100)]
ARM: dts: da850-evm: fix read access to SPI flash
Read access to the SPI flash are broken on da850-evm, i.e. the data
read is not what is actually programmed on the flash.
According to the datasheet for the M25P64 part present on the da850-evm,
if the SPI frequency is higher than 20MHz then the READ command is not
usable anymore and only the FAST_READ command can be used to read data.
This commit specifies in the DTS that we should use FAST_READ command
instead of the READ command.
Cc: stable@vger.kernel.org Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Fabien Parent <fparent@baylibre.com>
[nsekhar@ti.com: subject line adjustment] Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Declare virtio_config_ops structure as const as it is only stored in the
config field of a virtio_device structure. This field is of type const, so
virtio_config_ops structures having this property can be declared const.
Done using Coccinelle:
File size before and after applying the patch remains the same.
text data bss dec hex filename
9235 296 32928 42459 a5db drivers/s390/virtio/virtio_ccw.o
Colin Ian King [Tue, 27 Sep 2016 20:08:44 +0000 (13:08 -0700)]
virtio/s390: add missing \n to end of dev_err message
Trival fix, dev_err message is missing a \n, so add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Message-Id: <20160927200844.16008-1-colin.king@canonical.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Pierre Morel [Fri, 28 Aug 2015 09:09:32 +0000 (11:09 +0200)]
virtio/s390: support READ_STATUS command for virtio-ccw
As virtio-1 introduced the possibility of the device manipulating the
status byte, revision 2 of the virtio-ccw transport introduced a means
of getting the status byte from the device via READ_STATUS. Let's wire
it up for revisions >= 2 and fall back to returning the stored status
byte if not supported.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com> Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Halil Pasic [Mon, 29 Aug 2016 16:25:22 +0000 (18:25 +0200)]
tools/virtio/ringtest: fix run-on-all.sh for offline cpus
Since ef1b144d ("tools/virtio/ringtest: fix run-on-all.sh to work
without /dev/cpu") run-on-all.sh uses seq 0 $HOST_AFFINITY as the list
of ids of the CPUs to run the command on (assuming ids of online CPUs
are consecutive and start from 0), where $HOST_AFFINITY is the highest
CPU id in the system previously determined using lscpu. This can fail
on systems with offline CPUs.
Instead let's use lscpu to determine the list of online CPUs.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com> Fixes: ef1b144d ("tools/virtio/ringtest: fix run-on-all.sh to work without
/dev/cpu") Reviewed-by: Sascha Silbe <silbe@linux.vnet.ibm.com> Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
G. Campana [Thu, 19 Jan 2017 21:37:46 +0000 (23:37 +0200)]
virtio_console: fix a crash in config_work_handler
Using control_work instead of config_work as the 3rd argument to
container_of results in an invalid portdev pointer. Indeed, the work
structure is initialized as below:
It leads to a crash when portdev->vdev is dereferenced later. This
bug
is triggered when the guest uses a virtio-console without multiport
feature and receives a config_changed virtio interrupt.
Signed-off-by: G. Campana <gcampana@quarkslab.com> Reviewed-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If "head == vq->num" is true on the first iteration then "out" and "in"
aren't initialized. We handle that a few lines after the printk. I was
tempted to just delete the pr_debug() but I decided to just initialize
them to zero instead.
Also checkpatch.pl complains if variables are declared as just
"unsigned" without the "int".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Declare target_core_fabric_ops strucrues as const as they are only
passed as an argument to the functions target_register_template and
target_unregister_template. The arguments are of type const struct
target_core_fabric_ops *, so target_core_fabric_ops structures having
this property can be declared const.
Done using Coccinelle:
Josef Bacik [Thu, 19 Jan 2017 21:08:49 +0000 (16:08 -0500)]
nbd: only set MSG_MORE when we have more to send
A user noticed that write performance was horrible over loopback and we
traced it to an inversion of when we need to set MSG_MORE. It should be
set when we have more bvec's to send, not when we are on the last bvec.
This patch made the test go from 20 iops to 78k iops.
Signed-off-by: Josef Bacik <jbacik@fb.com> Fixes: 429a787be679 ("nbd: fix use-after-free of rq/bio in the xmit path") Signed-off-by: Jens Axboe <axboe@fb.com>
Linus Torvalds [Thu, 19 Jan 2017 17:59:46 +0000 (09:59 -0800)]
Merge tag 'pci-v4.10-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- recognize that a PCI-to-PCIe bridge originates a PCIe hierarchy, so
we enumerate that hierarchy correctly
- X-Gene: fix a change merged for v4.10 that broke MSI
- Keystone: avoid reading undefined registers, which can cause
asynchronous external aborts
- Supermicro X8DTH-i/6/iF/6F: ignore broken _CRS that caused us to
change (and break) existing I/O port assignments
* tag 'pci-v4.10-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/MSI: pci-xgene-msi: Fix CPU hotplug registration handling
PCI: Enumerate switches below PCI-to-PCIe bridges
x86/PCI: Ignore _CRS on Supermicro X8DTH-i/6/iF/6F
PCI: designware: Check for iATU unroll only on platforms that use ATU
Linus Torvalds [Thu, 19 Jan 2017 17:46:10 +0000 (09:46 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull two s390 bug fixes from Martin Schwidefsky:
"Two changes, the first is a fix to add a missing memory clobber to the
inline assembly to load control registers. This has not caused any
issues so far, but who knows what code gcc will generate in future
versions.
The second change is an update for the default configurations. This
includes CONFIG_BUG_ON_DATA_CORRUPTION=y, we want this to be enabled
for s390. The usual approach to debug problems on production systems
is to use crash on a system dump and for us avoiding data corruptions
is priority one"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: update defconfigs
s390/ctl_reg: make __ctl_load a full memory barrier
Mark Rutland [Wed, 18 Jan 2017 17:23:41 +0000 (17:23 +0000)]
arm64: avoid returning from bad_mode
Generally, taking an unexpected exception should be a fatal event, and
bad_mode is intended to cater for this. However, it should be possible
to contain unexpected synchronous exceptions from EL0 without bringing
the kernel down, by sending a SIGILL to the task.
We tried to apply this approach in commit 9955ac47f4ba1c95 ("arm64:
don't kill the kernel on a bad esr from el0"), by sending a signal for
any bad_mode call resulting from an EL0 exception.
However, this also applies to other unexpected exceptions, such as
SError and FIQ. The entry paths for these exceptions branch to bad_mode
without configuring the link register, and have no kernel_exit. Thus, if
we take one of these exceptions from EL0, bad_mode will eventually
return to the original user link register value.
This patch fixes this by introducing a new bad_el0_sync handler to cater
for the recoverable case, and restoring bad_mode to its original state,
whereby it calls panic() and never returns. The recoverable case
branches to bad_el0_sync with a bl, and returns to userspace via the
usual ret_to_user mechanism.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Fixes: 9955ac47f4ba1c95 ("arm64: don't kill the kernel on a bad esr from el0") Reported-by: Mark Salter <msalter@redhat.com> Cc: Will Deacon <will.deacon@arm.com> Cc: stable@vger.kernel.org Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Jason Gerecke [Tue, 17 Jan 2017 23:38:58 +0000 (15:38 -0800)]
HID: wacom: Fix sibling detection regression
Commit 345857b ("HID: wacom: generic: Add support for sensor offsets") included
a change to the operation and location of the call to 'wacom_add_shared_data'
in 'wacom_parse_and_register'. The modifications included moving it higher up
so that it would occur before the call to 'wacom_retrieve_hid_descriptor'. This
was done to prevent a crash that would have occured when the report containing
tablet offsets was fed into the driver with 'wacom_hid_report_raw_event'
(specifically: the various 'wacom_wac_*_report' functions were written with the
assumption that they would only be called once tablet setup had completed;
'wacom_wac_pen_report' in particular dereferences 'shared' which wasn't yet
allocated).
Moving the call to 'wacom_add_shared_data' effectively prevented the crash but
also broke the sibiling detection code which assumes that the HID descriptor
has been read and the various device_type flags set.
To fix this situation, we restore the original 'wacom_add_shared_data'
operation and location and instead implement an alternative change that can
also prevent the crash. Specifically, we notice that the report functions
mentioned above expect to be called only for input reports. By adding a check,
we can prevent feature reports (such as the offset report) from
causing trouble.
Fixes: 345857bb49 ("HID: wacom: generic: Add support for sensor offsets") Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com> Tested-by: Ping Cheng <pingc@wacom.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Vineet Gupta [Wed, 18 Jan 2017 23:10:52 +0000 (15:10 -0800)]
ARC: mm: split arc_cache_init to allow __init reaping of bulk
arc_cache_init() is called for each core so can't be tagged __init.
However bulk of it is only executed by master core and thus is candidate
for __init reaping.
Olof Johansson [Thu, 19 Jan 2017 00:11:03 +0000 (16:11 -0800)]
Merge tag 'omap-for-v4.10/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.10-rc cycle. Mostly a DMA regression fix for
omap1, and then a handful of trivial fixes for boards and devices to
work:
- Fixes TI wilink bluetooth strange platform data baud rate
- Remove duplicate pinmux line for am335x-icev2
- Fix omap1 dma regression
- Fix uninitialized return value for wkup_m3_ipc_probe()
- Fix Ethernet PHY binding typo for dra72-evm
- Fix init for omap5 and dra7 sata ports
- Fix mmc card detect pin for Logic PD SOM-LV
* tag 'omap-for-v4.10/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap3: Fix Card Detect and Write Protect on Logic PD SOM-LV
ARM: dts: OMAP5 / DRA7: indicate that SATA port 0 is available.
ARM: dts: dra72-evm-revc: fix typo in ethernet-phy node
soc: ti: wkup_m3_ipc: Fix error return code in wkup_m3_ipc_probe()
ARM: OMAP1: DMA: Correct the number of logical channels
ARM: dts: am335x-icev2: Remove the duplicated pinmux setting
ARM: OMAP2+: Fix WL1283 Bluetooth Baud Rate
Vineet Gupta [Wed, 18 Jan 2017 20:59:21 +0000 (12:59 -0800)]
ARCv2: IOC: Use actual memory size to setup aperture size
vs. fixed 512M before.
But this still assumes that all of memory is under IOC which may not be
true for the SoC. Improve that later when this becomes a real issue, by
specifying this from DT.
Vineet Gupta [Wed, 22 Jun 2016 10:31:19 +0000 (16:01 +0530)]
ARCv2: IOC: Adhere to progamming model guidelines to avoid DMA corruption
On AXS103 release bitfiles, DMA data corruptions were seen because IOC
setup was not following the recommended way in documentation.
Flipping IOC on when caches are enabled or coherency transactions are in
flight, might cause some of the memory operations to not observe
coherency as expected.
So strictly follow the programming model recommendations as documented
in comment header above arc_ioc_setup()
Arnd Bergmann [Wed, 18 Jan 2017 20:39:21 +0000 (12:39 -0800)]
xfs: fix xfs_mode_to_ftype() prototype
A harmless warning just got introduced:
fs/xfs/libxfs/xfs_dir2.h:40:8: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
Removing the 'const' modifier avoids the warning and has no
other effect.
Fixes: 1fc4d33fed12 ("xfs: replace xfs_mode_to_ftype table with switch statement") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Vineet Gupta [Mon, 16 Jan 2017 18:48:09 +0000 (10:48 -0800)]
ARC: module: Fix !CONFIG_ARC_DW2_UNWIND builds
commit d65283f7b695b5 added mod->arch.secstr under
CONFIG_ARC_DW2_UNWIND, but used it unconditionally which broke builds
when the option was disabled. Fix that by adjusting the #ifdef guard.
And while at it add a missing guard (for unwinder) in module.c as well
Reported-by: Waldemar Brodkorb <wbx@openadk.org> Cc: stable@vger.kernel.org #4.9 Fixes: d65283f7b695b5 ("ARC: module: elide loop to save reference to .eh_frame") Tested-by: Anton Kolesov <akolesov@synopsys.com> Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
[abrodkin: provided fixlet to Kconfig per failure in allnoconfig build] Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Linus Torvalds [Wed, 18 Jan 2017 19:13:41 +0000 (11:13 -0800)]
Merge branch 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull SMP hotplug update from Thomas Gleixner:
"This contains a trivial typo fix and an extension to the core code for
dynamically allocating states in the prepare stage.
The extension is necessary right now because we need a proper way to
unbreak LTTNG, which iscurrently non functional due to the removal of
the notifiers. Surely it's out of tree, but it's widely used by
distros.
The simple solution would have been to reserve a state for LTTNG, but
I'm not fond about unused crap in the kernel and the dynamic range,
which we admittedly should have done right away, allows us to remove
quite some of the hardcoded states, i.e. those which have no ordering
requirements. So doing the right thing now is better than having an
smaller intermediate solution which needs to be reworked anyway"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu/hotplug: Provide dynamic range for prepare stage
perf/x86/amd/ibs: Fix typo after cleanup state names in cpu/hotplug
Linus Torvalds [Wed, 18 Jan 2017 18:47:11 +0000 (10:47 -0800)]
Merge branch 'rcu-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU fixes from Ingo Molnar:
"This fixes sporadic ACPI related hangs in synchronize_rcu() that were
caused by the ACPI code mistakenly relying on an aspect of RCU that
was neither promised to work nor reliable but which happened to work -
until in v4.9 we changed the RCU implementation, which made the hangs
more prominent.
Since the mis-use of the RCU facility wasn't properly detected and
prevented either, these fixes make the RCU side work reliably instead
of working around the problem in the ACPI code.
Hence the slightly larger diffstat that goes beyond the normal scope
of RCU fixes in -rc kernels"
* 'rcu-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Narrow early boot window of illegal synchronous grace periods
rcu: Remove cond_resched() from Tiny synchronize_sched()
Linus Torvalds [Wed, 18 Jan 2017 18:45:22 +0000 (10:45 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"An Intel PMU driver hotplug fix and three 'perf probe' tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Handle exclusive threadid correctly on CPU hotplug
perf probe: Fix to probe on gcc generated functions in modules
perf probe: Add error checks to offline probe post-processing
perf probe: Fix to show correct locations for events on modules
Dave Martin [Wed, 18 Jan 2017 16:25:24 +0000 (16:25 +0000)]
arm64/ptrace: Reject attempts to set incomplete hardware breakpoint fields
We cannot preserve partial fields for hardware breakpoints, because
the values written by userspace to the hardware breakpoint
registers can't subsequently be recovered intact from the hardware.
So, just reject attempts to write incomplete fields with -EINVAL.
Cc: <stable@vger.kernel.org> # 3.7.x- Fixes: 478fcb2cdb23 ("arm64: Debugging support") Signed-off-by: Dave Martin <Dave.Martin@arm.com> Acked-by: Will Deacon <Will.Deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
projects / karo-tx-linux.git / log