The hueristic was designed to avoid using locality group preallocation
when writing the last segment of a closed file. Fix it by move
setting size to the maximum of size and isize until after we check
whether size == isize.
In an attempt to avoid doing an unneeded flush after opening a
(previously non-existent) file with O_CREAT|O_TRUNC, the code only
triggered the hueristic if ei->disksize was non-zero. Turns out that
the VFS doesn't call ->truncate() if the file doesn't exist, and
ei->disksize is always zero even if the file previously existed. So
remove the test, since it isn't necessary and in fact disabled the
hueristic.
Thanks to Clemens Eisserer that he was seeing problems with files
written using kwrite and eclipse after sudden crashes caused by a
buggy Intel video driver.
EXT4_EXT_MIGRATE is only intended to be used for an in-memory flag,
and the hex value assigned to it collides with FS_DIRECTIO_FL (which
is also stored in i_flags). There's no reason for the
EXT4_EXT_MIGRATE bit to be stored in i_flags, so we switch it to use
i_state instead.
Today, the ext4 allocator will happily allocate blocks past
2^32 for indirect-block files, which results in the block
numbers getting truncated, and corruption ensues.
This patch limits such allocations to < 2^32, and adds
BUG_ONs if we do get blocks larger than that.
This should address RH Bug 519471, ext4 bitmap allocator
must limit blocks to < 2^32
* ext4_find_goal() is modified to choose a goal < UINT_MAX,
so that our starting point is in an acceptable range.
* ext4_xattr_block_set() is modified such that the goal block
is < UINT_MAX, as above.
* ext4_mb_regular_allocator() is modified so that the group
search does not continue into groups which are too high
* ext4_mb_use_preallocated() has a check that we don't use
preallocated space which is too far out
* ext4_alloc_blocks() and ext4_xattr_block_set() add some BUG_ONs
No attempt has been made to limit inode locations to < 2^32,
so we may wind up with blocks far from their inodes. Doing
this much already will lead to some odd ENOSPC issues when the
"lower 32" gets full, and further restricting inodes could
make that even weirder.
For high inodes, choosing a goal of the original, % UINT_MAX,
may be a bit odd, but then we're in an odd situation anyway,
and I don't know of a better heuristic.
If logical block offset of original file which is passed to
EXT4_IOC_MOVE_EXT is different from donor file's,
a calculation error occurs in ext4_calc_swap_extents(),
therefore wrong block is exchanged between original file and donor file.
As a result, we hit ext4_error() in check_block_validity().
To detect the logical offset difference in EXT4_IOC_MOVE_EXT,
add checks to mext_calc_swap_extents() and handle it as error,
since data exchange must be done between the same blocks in EXT4_IOC_MOVE_EXT.
There is the possibility that path structure which is taken
by ext4_ext_find_extent() indicates null extents.
Because during data block exchanging in ext4_move_extents(),
constitution of an extent tree may be changed.
As a solution, the patch adds null extent check
to ext_get_path().
Replace BUG_ON calls with a call to ext4_error()
to print an error message if EXT4_IOC_MOVE_EXT failed
with some kind of reasons. This will help to debug.
Ted pointed this out, thanks.
Replace get_ext_path macro with an inline function,
since this macro looks like a function call but its arguments
get modified. Ted pointed this out, thanks.
Using relative pathnames in #include statements interacts badly with
SystemTap, since the fs/ext4/*.h header files are not packaged up as
part of a distribution kernel's header files. Since systemtap doesn't
use TP_fast_assign(), we can use a blind structure definition and then
make sure the needed header files are defined before the ext4 source
files #include the trace/events/ext4.h header file.
The s_flex_groups array should have been initialized using atomic_add
to sum up the free counts from the block groups that make up a
flex_bg. By using atomic_set, the value of the s_flex_groups array
was set to the values of the last block group in the flex_bg.
The impact of this bug is that the block and inode allocation
algorithms might not pick the best flex_bg for new allocation.
Thanks to Damien Guibouret for pointing out this problem!
When ext4_dx_add_entry() has to split an index node, it has to ensure that
name_len of dx_node's fake_dirent is also zero, because otherwise e2fsck
won't recognise it as an intermediate htree node and consider the htree to
be corrupted.
This avoids updating the superblock write time when we are mounting
the root file system read/only but we need to replay the journal; at
that point, for people who are east of GMT and who make their clock
tick in localtime for Windows bug-for-bug compatibility, and this will
cause e2fsck to complain and force a full file system check.
We should check for need init flag with the group's alloc_sem held, to
make sure while we are loading the buddy cache and holding a reference
to it, a file system resize can't add new blocks to same group.
The patch also drops the need init flag check in
ext4_mb_regular_allocator() because doing the check without holding
alloc_sem is racy.
Teach ext4_write_inode() and ext4_do_update_inode() about non-journal
mode: If we're not using a journal, ext4_write_inode() now calls
ext4_do_update_inode() (after getting the iloc via ext4_get_inode_loc())
with a new "do_sync" parameter. If that parameter is nonzero _and_ we're
not using a journal, ext4_do_update_inode() calls sync_dirty_buffer()
instead of ext4_handle_dirty_metadata().
This problem was found in power-fail testing, checking the amount of
loss of files and blocks after a power failure when using fsync() and
when not using fsync(). It turned out that using fsync() was actually
worse than not doing so, possibly because it increased the likelihood
that the inodes would remain unflushed and would therefore be lost at
the power failure.
When there is no journal present, we must attach buffer heads
associated with extent tree and indirect blocks to the inode's
mapping->private_list via mark_buffer_dirty_inode() so that
ext4_sync_file() --- which is called to service fsync() and
fdatasync() system calls --- can write out the inode's metadata blocks
by calling sync_mapping_buffers().
When ext4 is using a journal, a metadata block which is deallocated
must be passed into the journal layer so it can be dropped from the
current transaction and/or revoked. This is done by calling the
functions ext4_journal_forget() and ext4_journal_revoke(), which call
jbd2_journal_forget(), and jbd2_journal_revoke(), respectively.
Since the jbd2_journal_forget() and jbd2_journal_revoke() call
bforget(), if ext4 is not using a journal, ext4_journal_forget() and
ext4_journal_revoke() must call bforget() to avoid a dirty metadata
block overwriting a block after it has been reallocated and reused for
another inode's data block.
Drop the WARN_ON(1), as he stack trace is not appropriate, since it is
triggered by file system corruption, and it misleads users into
thinking there is a kernel bug. In addition, change the message
displayed by ext4_error() to make it clear that this is a file system
corruption problem.
The ext4_move_extents() functions checks with BUG_ON() whether the
exchanged blocks count accords with request blocks count. But, if the
target range (orig_start + len) includes sparse block(s), 'moved_len'
(exchanged blocks count) does not agree with 'len' (request blocks
count), since sparse block is not counted in 'moved_len'. This causes
us to hit the BUG_ON(), even though the function succeeded.
The mext_check_arguments() function in move_extents.c has wrong
comparisons. orig_start which is passed from user-space is block
unit, but i_size of inode is byte unit, therefore the checks do not
work fine. This mis-check leads to the overflow of 'len' and then
hits BUG_ON() in ext4_move_extents(). The patch fixes this issue.
We need to flush the write cache unconditionally in ->fsync, otherwise
writes into already allocated blocks can get lost. Writes into fully
allocated files are very common when using disk images for
virtualization, and without this fix can easily lose data after
an fdatasync, which is the typical implementation for a cache flush on
the virtual drive.
Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
To solve a lock inversion problem, we implement part of the
range_cyclic algorithm in ext4_da_writepages(). (See commit 2acf2c26
for more details.)
As part of that change wbc->range_start was modified by ext4's
writepages function, which causes its callers to get confused since
they aren't expecting the filesystem to modify it. The simplest fix
is to save and restore wbc->range_start in ext4_da_writepages.
In ext4_link we need to check using EXT4_LINK_MAX, and not
EXT4_DIR_LINK_MAX(), since ext4_link() is creating hard links of
regular files, and not directories.
We need to unlock the new inode before iput. This patch fixes the
following warning when calling chattr +e to migrate a file to use
extents. It also fixes problems in when e4defrag attempts to
defragment an inode.
A user reported that although his root ext4 filesystem was mounting
fine, other filesystems would not mount, with the:
"Filesystem with huge files cannot be mounted RDWR without CONFIG_LBDAF"
error on his 32-bit box built without CONFIG_LBDAF. This is because
the test at mount time for this situation was not being re-checked
on remount, and the normal boot process makes an ro->rw transition,
so this was being missed.
Refactor to make a common helper function to test the filesystem
features against the type of mount request (RO vs. RW) so that we
stay consistent.
Addresses Red-Hat-Bugzilla: #517650
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
ext4 will happily mount a > 16T filesystem on a 32-bit box, but
this is not safe; writes to the block device will wrap past 16T
and the page cache can't index past 16T (232 index * 4k pages).
Adding another test to the existing "too many sectors" test
should do the trick.
Add a comment, a relevant return value, and fix the reference
to the CONFIG_LBD(AF) option as well.
Jan Kara [Tue, 18 Aug 2009 02:17:20 +0000 (22:17 -0400)]
ext4: Fix possible deadlock between ext4_truncate() and ext4_get_blocks()
During truncate we are sometimes forced to start a new transaction as
the amount of blocks to be journaled is both quite large and hard to
predict. So far we restarted a transaction while holding i_data_sem
and that violates lock ordering because i_data_sem ranks below a
transaction start (and it can lead to a real deadlock with
ext4_get_blocks() mapping blocks in some page while having a
transaction open).
We fix the problem by dropping the i_data_sem before restarting the
transaction and acquire it afterwards. It's slightly subtle that this
works:
1) By the time ext4_truncate() is called, all the page cache for the
truncated part of the file is dropped so get_block() should not be
called on it (we only have to invalidate extent cache after we
reacquire i_data_sem because some extent from not-truncated part could
extend also into the part we are going to truncate).
2) Writes, migrate or defrag hold i_mutex so they are stopped for all
the time of the truncate.
This bug has been found and analyzed by Theodore Tso <tytso@mit.edu>.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
lockdep annotation for a transaction start has been at the end of
jbd2_journal_start(). But a transaction is also started from
jbd2_journal_restart(). Move the lockdep annotation to start_this_handle()
which covers both cases.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently the group preallocation code tries to find a large (512)
free block from which to do per-cpu group allocation for small files.
The problem with this scheme is that it leaves the filesystem horribly
fragmented. In the worst case, if the filesystem is unmounted and
remounted (after a system shutdown, for example) we forget the fact
that wee were using a particular (now-partially filled) 512 block
extent. So the next time we try to allocate space for a small file,
we will find *another* completely free 512 block chunk to allocate
small files. Given that there are 32,768 blocks in a block group,
after 64 iterations of "mount, write one 4k file in a directory,
unmount", the block group will have 64 files, each separated by 511
blocks, and the block group will no longer have any free 512
completely free chunks of blocks for group preallocation space.
So if we try to allocate blocks for a file that has been closed, such
that we know the final size of the file, and the filesystem is not
busy, avoid using group preallocation.
The logic around sbi->s_mb_last_group and sbi->s_mb_last_start was all
screwed up. These fields were getting unconditionally all the time,
set even when stream allocation had not taken place, and if they were
being used when the file was smaller than s_mb_stream_request, which
is when the allocation should _not_ be doing stream allocation.
Fix this by determining whether or not we stream allocation should
take place once, in ext4_mb_group_or_file(), and setting a flag which
gets used in ext4_mb_regular_allocator() and ext4_mb_use_best_found().
This simplifies the code and assures that we are consistently using
(or not using) the stream allocation logic.
move_extent_par_page calls a_ops->write_begin() to increase journal
handler's reference count. However, if either mext_replace_branches()
or ext4_get_block fails, the increased reference count isn't
decreased. This will cause a later attempt to umount of the fs to hang
forever. The patch addresses the issue by calling ext4_journal_stop()
if page is not NULL (which means a_ops->write_end() isn't invoked).
fix jiffie rounding in jbd commit timer setup code. Rounding down
could cause the timer to be fired before the corresponding transaction
has expired. That transaction can stay not committed forever if no
new transaction is created or expicit sync/umount happens.
Signed-off-by: Alex Zhuravlev (Tomas) <alex.zhuravlev@sun.com> Signed-off-by: Andreas Dilger <adilger@sun.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The allocation of the ext4_group_info array was moved to a new
function ext4_mb_add_group_info() in commit 5f21b0e6 so that online
resize would use a common (and correct) codepath. Unfortunately, the
call to the new ext4_mb_add_group_info() function was added without
removing the code which originally allocated the array. This caused a
memory leak each time an ext4 filesystem was mounted.
The fix is simple; remove the code that did the original allocation,
since it is no longer needed.
Keysyms stored in key_map[] are not simply K() values, but U(K()) values,
as can be seen in the KDSKBENT ioctl handler. The kernel-generated
braille keysyms thus need a U() call too.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Return temperature in milidegree instead of degree, as sysfs-api requires
the temperature in milidegree.
Signed-off-by: Peter Feuerer <peter@piie.net> Tested-by: Borislav Petkov <petkovbb@gmail.com> Cc: Andreas Mohr <andi@lisas.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Peter Feuerer <peter@piie.net> Cc: Andreas Mohr <andi@lisas.de> Cc: Borislav Petkov <petkovbb@googlemail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A bug was seen on boards using a PLX 8518 switch device which advertises
AER on each of it's transparent bridges. The AER driver was loaded for
each bridge and this driver tried to access the AER source ID register
whenever an interrupt occured on the shared PCI INTX lines. The source
ID register does not exist on non root port PCIE device's which
advertise AER and trying to access this register causes a unsupported
request error on the bridge. Thus, when the next interrupt occurs,
another error is found and the non existent source ID register is
accessed again, and so it goes on.
The result is a spammed dmesg with unsupported request PCI express
errors on the bridge device that the AER driver is loaded against.
Many boards have a bug-free ns16550 compatible serial port, which we should
register as PORT_16550A. This introduces a new value "ns16550a" for the
compatible property of of_serial to let a firmware choose that model instead
of using the crippled PORT_16550 mode.
When the framebuffer driver does not publish detailed timing information
for the current video mode, the correct value for the pixclock field is
zero, not -1.
Since pixclock is actually unsigned, the value -1 would be interpreted
as 4294967295 picoseconds (i.e., about 4 milliseconds) by
register_framebuffer() and userspace programs.
This patch allows X.org's fbdev driver to work.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Tested-by: Paulius Zaleckas <paulius.zaleckas@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Apply Borislav Petkov's patch (convert the fancmd[] array to a real
struct thus disambiguating command handling and making code more
readable.)
- Add BIOS product to BIOS table as AOA110 and AOA150 have different
register values
- Add force_product parameter to allow forcing different product
- fix linker warning caused by "acerhdf_drv" not being named
"acerhdf_driver"
Signed-off-by: Peter Feuerer <peter@piie.net> Cc: Andreas Mohr <andi@lisas.de> Acked-by: Borislav Petkov <petkovbb@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> Cc: Adrian von Bidder <avbidder@fortytwo.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix userspace_device list corruption. The corruption was caused by
clients not being removed when adapters with such clients were
themselves removed. Something like the following would trigger it
(assuming i2c-stub gets adapter number 3):
* Set correct xpd curve indices for high/low gain curves during
rfbuffer setup on RF5112B with both calibration curves available.
* Don't return zero min power when we have the same pcdac value
twice because it breaks interpolation. Instead return the right
x barrier as we do when we have equal power levels for 2 different
pcdac values.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: Dan Williams <dcbw@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Before bringing up a sky2 interface up ethtool reports
"Link detected: yes". Do as ixgbe does and netif_carrier_off() on
probe().
Signed-off-by: Brandon Philips <bphilips@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
b43 allocates a bouncebuffer, if the supplied TX skb is in an invalid
memory range for DMA.
However, this is broken in that it fails to copy over some metadata to the
new skb.
This patch fixes three problems:
* Failure to adjust the ieee80211_tx_info pointer to the new buffer.
This results in a kmemcheck warning.
* Failure to copy the skb cb, which contains ieee80211_tx_info, to the new skb.
This results in breakage of various TX-status postprocessing (Rate control).
* Failure to transfer the queue mapping.
This results in the wrong queue being stopped on saturation and can result in queue overflow.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Tested-by: Christian Casteyde <casteyde.christian@free.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit v2.6.28-rc1~717^2~109^2~2 was slightly incomplete; not all
instances of par->match->family were changed to par->family.
References: http://bugzilla.netfilter.org/show_bug.cgi?id=610 Signed-off-by: Jan Engelhardt <jengelh@medozas.de> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Vitezslav Samel discovered that since 2.6.30.4+ active FTP can not work
over NAT. The "cause" of the problem was a fix of unacknowledged data
detection with NAT (commit a3a9f79e361e864f0e9d75ebe2a0cb43d17c4272).
However, actually, that fix uncovered a long standing bug in TCP conntrack:
when NAT was enabled, we simply updated the max of the right edge of
the segments we have seen (td_end), by the offset NAT produced with
changing IP/port in the data. However, we did not update the other parameter
(td_maxend) which is affected by the NAT offset. Thus that could drift
away from the correct value and thus resulted breaking active FTP.
The patch below fixes the issue by *not* updating the conntrack parameters
from NAT, but instead taking into account the NAT offsets in conntrack in a
consistent way. (Updating from NAT would be more harder and expensive because
it'd need to re-calculate parameters we already calculated in conntrack.)
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The comment says that limits are cached for 60 seconds but the code
actually caches them for only 2 seconds. Align the code on the
comment, as 60 seconds makes more sense.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Cc: Jordan Crouse <jordan@cosmicpenguin.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The logic of temperature fault flags is wrong, it shows faults when
there are none and vice versa. Fix it.
I can't believe this has been broken since the driver was added, 8
months ago, basically breaking temp1 and temp3, and nobody ever
complained.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Cc: Jordan Crouse <jordan@cosmicpenguin.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 0762b8bde9729f10f8e6249809660ff2ec3ad735
(from 14 months ago) introduced a use-after-free bug which has just
recently started manifesting in my md testing.
I tried git bisect to find out what caused the bug to start
manifesting, and it could have been the recent change to
blk_unregister_queue (48c0d4d4c04) but the results were inconclusive.
This patch certainly fixes my symptoms and looks correct as the two
calls are now in the same order as elsewhere in that function.
Fix soft-lockup in hso.c which is triggered on SMP machine when
modem is removed while file descriptor(s) under /dev are still open:
old version called kref_put() too early which resulted in destroying
hso_serial and hso_device objects which were still used later on.
Signed-off-by: Antti Kaijanmäki <antti.kaijanmaki@nomovok.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
The loop in perf_ctx_adjust_freq checks the frequency of sampling
event counters, and adjusts the event interval and unthrottles the
event if required, and resets the interrupt count for the event.
However, at present it only looks at group leaders.
This means that a sampling event that is not a group leader will
eventually get throttled, once its interrupt count reaches
sysctl_perf_event_sample_rate/HZ --- and that is guaranteed to
happen, if the event is active for long enough, since the interrupt
count never gets reset. Once it is throttled it never gets
unthrottled, so it basically just stops working at that point.
This fixes it by making perf_ctx_adjust_freq use ctx->event_list
rather than ctx->group_list. The existing spin_lock/spin_unlock
around the loop makes it unnecessary to put rcu_read_lock/
rcu_read_unlock around the list_for_each_entry_rcu().
Reported-by: Mark W. Krentel <krentel@cs.rice.edu> Signed-off-by: Paul Mackerras <paulus@samba.org> Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <19157.26731.855609.165622@cargo.ozlabs.ibm.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 4706b349f was a forward port of a fix that was needed
for SLES10. But in fact it is not needed in mainline because
the earlier commit dd00a99e7a fixes the same problem in a
better way.
Further, this commit introduces a bug in the way it interacts with
the automatic read-error-correction. If, after a read error is
successfully corrected, the same disk is chosen to re-read - the
re-read won't be attempted but an error will be returned instead.
After reverting that commit, there is the possibility that a
read error on a read-only array (where read errors cannot
be corrected as that requires a write) will repeatedly read the same
device and continue to get an error.
So in the "Array is readonly" case, fail the drive immediately on
a read error.
On the parisc architecture we face for each and every loaded kernel module
this kernel "badness warning":
sysfs: cannot create duplicate filename '/module/ac97_bus/sections/.text'
Badness at fs/sysfs/dir.c:487
Reason for that is, that on parisc all kernel modules do have multiple
.text sections due to the usage of the -ffunction-sections compiler flag
which is needed to reach all jump targets on this platform.
An objdump on such a kernel module gives:
Sections:
Idx Name Size VMA LMA File off Algn
0 .note.gnu.build-id 00000024000000000000000000000034 2**2
CONTENTS, ALLOC, LOAD, READONLY, DATA
1 .text 00000000000000000000000000000058 2**0
CONTENTS, ALLOC, LOAD, READONLY, CODE
2 .text.ac97_bus_match 0000001c000000000000000000000058 2**2
CONTENTS, ALLOC, LOAD, READONLY, CODE
3 .text 000000000000000000000000000000d4 2**0
CONTENTS, ALLOC, LOAD, READONLY, CODE
...
Since the .text sections are empty (size of 0 bytes) and won't be
loaded by the kernel module loader anyway, I don't see a reason
why such sections need to be listed under
/sys/module/<module_name>/sections/<section_name> either.
The attached patch does solve this issue by not exporting section
names which are empty.
This fixes bugzilla http://bugzilla.kernel.org/show_bug.cgi?id=14703
mmc_remove_host() will cause the mmc core to switch off the bus power by
eventually calling pxamci_set_ios(). This function uses the regulator or
the GPIO which have been freed already.
a quirky chipset needs periodic schedules to run for a minimum
time before they can be disabled again. This enforces the requirement
with a time stamp and a calculated delay
Signed-off-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The use of urb->actual_length to update tx_outstanding_bytes
implicitly assumes that the number of bytes actually written is the
same as the number of bytes we tried to write. On error that
assumption is violated so just use transfer_buffer_length the number
of bytes we intended to write to the device.
If an error occurs we need to fall through and call
usb_serial_port_softint to wake up processes waiting in
tty_wait_until_sent.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- fixed shared interrupt bug reported by Vadim Lobanov
- fixed possible warning oops on driver unload when connected
- prevent interrupt flood in PIO mode ("modprobe amd5536udc use_dma=0")
when using gadget ether
Signed-off-by: Thomas Dahlmann <dahlmann.thomas@arcor.de> Cc: Robert Richter <robert.richter@amd.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver incorrectly cancels the mass-storage device CSW request
(which leads to device reset) due to giving back URB at the head of
endpoint's queue after sending each STALL handshake; stop doing that
and start checking for the queue being non-empty before stalling an
endpoint and disallowing stall in such case in musb_gadget_set_halt()
like the other gadget drivers do.
Moreover, the driver starts Rx request despite of the endpoint being
halted -- fix this by moving the SendStall bit check from musb_g_rx()
to rxstate(). And we also sometimes get into rxstate() with DMA still
active after clearing an endpoint's halt (not clear why), so bail out
in this case, similarly to what txstate() does...
While at it, also do the following changes :
- in musb_gadget_set_halt(), remove pointless Tx FIFO flushing (the
driver does not allow stalling with non-empty Tx FIFO anyway);
- in rxstate(), stop pointlessly zeroing the 'csr' variable;
- in musb_gadget_set_halt(), move the 'done' label to a more proper
place;
- in musb_g_rx(), eliminate the 'done' label completely...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1304) fixes a regression in ehci-hcd. Evidently some
hubs don't handle Clear-TT-Buffer requests correctly, so we should
avoid sending them when they don't appear to be absolutely necessary.
The reported symptom is that output on a downstream audio device cuts
out because the hub stops relaying isochronous packets.
The patch prevents Clear-TT-Buffer requests from being sent following
a STALL handshake. In theory a STALL indicates either that the
downstream device sent a STALL or that no matching TT buffer could be
found. In either case, the transfer is completed and the TT buffer
does not remain busy, so it doesn't need to be cleared.
Also, the patch fixes a minor flaw in the code that actually sends the
Clear-TT-Buffer requests. Although the pipe direction isn't really
used for control transfers, it should be a Send rather than a Receive.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Javier Kohen <jkohen@users.sourceforge.net> CC: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"[CPUFREQ] cpumask: avoid playing with cpus_allowed in speedstep-ich.c"
changed the code to mistakenly pass the current cpu as the "processor"
argument of speedstep_get_frequency(), whereas it should be the type of
the processor.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Acked-by: Dominik Brodowski <linux@brodo.de> Reported-by: Dave Mueller <dave.mueller@gmx.ch> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ipv4 ip_frag_reasm(), fully replace 'dev_net(dev)' with 'net', defined
previously patched into 2.6.29.
Between 2.6.28.10 and 2.6.29, net/ipv4/ip_fragment.c was patched,
changing from dev_net(dev) to container_of(...). Unfortunately the goto
section (out_fail) on oversized packets inside ip_frag_reasm() didn't
get touched up as well. Oversized IP packets cause a NULL pointer
dereference and immediate hang.
I discovered this running openvasd and my previous email on this is
titled: NULL pointer dereference at 2.6.32-rc8:net/ipv4/ip_fragment.c:566
Signed-off-by: David Ford <david@blue-labs.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Hauppauge WinTV HVR-1150 retail boards require the FORCE_TS_VALID bit
to be set in order to function properly. This change will work on the early
revisions on the board as well, but the final revision will not function
without this change.
When FORCE_TS_VALID mode is enabled, the saa713x will accept MPEG TS input
without requiring TS_VALID set high. This is required for some new boards
to function properly, due to the hardware design implementation.
The configuration is toggled within the board setup configuration. Boards
that do not have this bit set will function as before with no change.
> We allocate and zero cpu_isolated_map after the isolcpus
> __setup option has run. This means cpu_isolated_map always
> ends up empty and if CPUMASK_OFFSTACK is enabled we write to a
> cpumask that hasn't been allocated.
I introduced this regression in 49557e620339cb13 (sched: Fix
boot crash by zalloc()ing most of the cpu masks).
Use the bootmem allocator if they set isolcpus=, otherwise
allocate and zero like normal.
Reported-by: Anton Blanchard <anton@samba.org> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: peterz@infradead.org Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <200912021409.17013.rusty@rustcorp.com.au> Signed-off-by: Ingo Molnar <mingo@elte.hu> Tested-by: Anton Blanchard <anton@samba.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
`>>' has a higher precedence than `?' so src2 evaluated to
either 16 or 0 dependent on the bits set in rs2.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Page buffers containing packets with an incorrect checksum or using a
protocol not handled by hardware checksum offload were previously not
passed to LRO. The conversion to GRO changed this, but did not set
the ip_summed value accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify bonding hash transmit policies to use the psource MAC address of
the packet instead of the MAC address configured for the bonding device.
The old sitation conflicts with the documentation.
Signed-off-by: Jasper Spaans <spaans@fox-it.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On UDP sockets, we must call skb_free_datagram() with socket locked,
or risk sk_forward_alloc corruption. This requirement is not respected
in SUNRPC.
Add a convenient helper, skb_free_datagram_locked() and use it in SUNRPC
Reported-by: Francis Moreau <francis.moro@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pedit will reject a policy that is large because it
uses the wrong structure in the policy validation.
This fixes it.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If ace_load_firmware() fails, ace_init() cleans up but still returns
0, leading to an oops as seen in <http://bugs.debian.org/521383>.
It should pass the error code up.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
udp_poll() can in some circumstances drop frames with incorrect checksums.
Problem is we now have to lock the socket while dropping frames, or risk
sk_forward corruption.
This bug is present since commit 95766fff6b9a78d1
([UDP]: Add memory accounting.)
While we are at it, we can correct ioctl(SIOCINQ) to also drop bad frames.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The VIDIOC_G_STD ioctl may not be present in the case of radio receivers.
In that case G_STD will return an error. The v4l1-compat layer should not
attempt to propagate that error to the caller, instead it should be
ignored.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / karo-tx-linux.git / log