Per Forlin [Mon, 14 Nov 2011 11:04:24 +0000 (12:04 +0100)]
mmc: mmc_test: align max_seg_size
If max_seg_size is unaligned, mmc_test_map_sg() may create sg element
sizes that are not aligned with 512 byte. Fix, align max_seg_size at
mmc_test_area_init().
Signed-off-by: Per Forlin <per.forlin@stericsson.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Kyungmin Park [Thu, 17 Nov 2011 04:34:33 +0000 (13:34 +0900)]
mmc: core: Fix typo at mmc_card_sleep
Fix wrong bus_ops->sleep check. (This isn't expected to have real-world
consequences, because the mmc core always defines both 'awake' and
'sleep' ops.)
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Philip Rakity [Tue, 15 Nov 2011 03:14:38 +0000 (19:14 -0800)]
mmc: sdio: support SDIO UHS cards
This patch adds support for sdio UHS cards per the version 3.0
spec.
UHS mode is only enabled for version 3.0 cards when both the
host and the controller support UHS modes.
1.8v signaling support is removed if both the card and the
host do not support UHS. This is done to maintain
compatibility and some system/card combinations break when
1.8v signaling is enabled when the host does not support UHS.
Signed-off-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Aaron Lu <Aaron.lu@amd.com> Reviewed-by: Arindam Nath <arindam.nath@amd.com> Tested-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Girish K S [Tue, 15 Nov 2011 06:25:46 +0000 (11:55 +0530)]
mmc: core: Fix power_off_notify during suspend
The eMMC 4.5 devices respond to only RESET and AWAKE command in the
sleep state. Hence the mmc switch command to notify power off state
should be sent before the device enters sleep state.
This patch fixes the same.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: core: Use delayed work in clock gating framework
Current clock gating framework disables the MCI clock as soon as the
request is completed and enables it when a request arrives. This aggressive
clock gating framework, when enabled, cause following issues:
When there are back-to-back requests from the Queue layer, we unnecessarily
end up disabling and enabling the clocks between these requests since 8MCLK
clock cycles is a very short duration compared to the time delay between
back to back requests reaching the MMC layer. This overhead can effect the
overall performance depending on how long the clock enable and disable
calls take which is platform dependent. For example on some platforms we
can have clock control not on the local processor, but on a different
subsystem and the time taken to perform the clock enable/disable can add
significant overhead.
Also if the host controller driver decides to disable the host clock too
when mmc_set_ios function is called with ios.clock=0, it adds additional
delay and it is highly possible that the next request had already arrived
and unnecessarily blocked in enabling the clocks. This is seen frequently
when the processor is executing at high speeds and in multi-core platforms
thus reduces the overall throughput compared to if clock gating is
disabled.
Fix this by delaying turning off the clocks by posting request on
delayed workqueue. Also cancel the unscheduled pending work, if any,
when there is access to card.
sysfs entry is provided to tune the delay as needed, default
value set to 200ms.
Girish K S [Fri, 4 Nov 2011 10:52:47 +0000 (16:22 +0530)]
mmc: core: Fix setting power notify state variable for non-eMMC
This patch skips the setting of the power notify state variable
for non eMMC 4.5 devices. Also fixes the problem of omap_hsmmc
noisy/broken for suspend resume reported by Kevin Hilman.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org> Acked-by: Ulf Hansson <ulf.hansson@stericsson.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Chris Ball [Sat, 12 Nov 2011 03:01:43 +0000 (22:01 -0500)]
mmc: card: Use manufacturer ID symbols in card quirks.
No functional change; adds macros for card manufacturer IDs.
Signed-off-by: Chris Ball <cjb@laptop.org> Cc: Andrei E. Warkentin <andrey.warkentin@gmail.com> Cc: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Adds a quirk that sets the data read timeout to a fixed value instead
of relying on the information in the CSD. The timeout value chosen
is 300ms since that has proven enough for the problematic cards found,
but could be increased if other cards require this.
This patch also enables this quirk for certain Micron cards known to
have this problem.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com> Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Cc: <stable@kernel.org> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: debugfs: expose the SDCLK frq in sys ios (V6)
This patch is to expose the actual SDCLK frequency in
/sys/kernel/debug/mmcX/ios entry.
For example, if the max clk for a normal speed card is 20MHz this
is reported in /sys/kernel/debug/mmcX/ios. Unfortunately the actual
SDCLK frequency (i.e. Baseclock / divisor) is not reported at all:
for example, in that case, on Arasan HC, it should be 48/4=12 (MHz).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: sdio: Fix to support any block size optimally
This patch allows any block size to be set on the SDIO link,
and still have an arbitrary sized packet (adjusted in size by
using sdio_align_size) transferred in an optimal way
(preferably one transfer).
Previously if the block size was larger than the default of
512 bytes and the transfer size was exactly one block size
(possibly thanks to using sdio_align_size to get an optimal
transfer size), it was sent as a number of byte transfers instead
of one block transfer. Also if the number of blocks was
(max_blocks * N) + 1, the tranfer would be conducted with a number
of blocks and finished off with a number of byte transfers.
When doing this change it was also possible to break out the quirk
for broken byte mode in a much cleaner way, and collect the logic of
when to do byte or block transfer in one function instead of two.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com> Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Sascha Hauer [Fri, 11 Nov 2011 15:28:05 +0000 (16:28 +0100)]
mmc: mxcmmc: fix falling back to PIO
When we can't configure the dma channel we want to fall
back to PIO. We do this by setting host->do_dma to zero.
This does not work as do_dma is used to see whether dma
can be used for the current transfer. Instead, we have
to set host->dma to NULL.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Cc: <stable@kernel.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Per Forlin [Mon, 7 Nov 2011 16:25:11 +0000 (21:55 +0530)]
mmc: omap_hsmmc: DMA unmap only once in case of MMC error
Reported by Russell King:
mmcblk0: error -84 transferring data, sector 149201, nr 64,
cmd response 0x900, card status 0xb00
mmcblk0: retrying using single block read
WARNING: at lib/dma-debug.c:811 check_unmap
omap_hsmmc omap_hsmmc.0: DMA-API: device driver tries to free DMA memory
it has not allocated [device address=0x0000000080933000] [size=20480 bytes]
In case of an error dma_unmap() is issued in omap_hsmmc_dma_cleanup()
and then again in omap_hsmmc_post_req(). Resolve this by clearing the
host_cookie to indicate there is no DMA mapped memory to unmap.
Signed-off-by: Per Forlin <per.forlin@linaro.org> Tested-by: Balaji T K <balajitk@ti.com> Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Chris Ball <cjb@laptop.org>
Namjae Jeon [Wed, 12 Oct 2011 15:43:14 +0000 (00:43 +0900)]
mmc: fix compile error when CONFIG_BLOCK is not enabled
'DISK_NAME_LEN' is undeclared when CONFIG_BLOCK is disabled; its use was
introduced via genhd.h by the general purpose partition patch.
To fix, we just add our own MAX_MMC_PART_NAME_LEN macro instead of using
DISK_NAME_LEN.
Reported-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Namjae Jeon <linkinjeon@gmail.com> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Acked-by: Andrei Warkentin <andreiw@vmware.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Seungwon Jeon [Tue, 25 Oct 2011 00:43:12 +0000 (09:43 +0900)]
mmc: core: Cleanup eMMC4.5 conditionals
Code cleanup, putting all eMMC 4.5 detection cases together.
This patch removes one if-statement and assembles all. And it also
removes variable initialization below else-statement -- all members
of card structure are already set to zero at card-init.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Paul Walmsley [Thu, 6 Oct 2011 20:50:35 +0000 (14:50 -0600)]
mmc: omap_hsmmc: if multiblock reads are broken, disable them
When device data indicates that multiple block reads are not supported
on a given HSMMC controller instance, log a message to the console, and
pass the appropriate MMC capability flag to the MMC core.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Dave Hylands <dhylands@gmail.com> Tested-by: Steve Sakoman <sakoman@gmail.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Paul Walmsley [Thu, 6 Oct 2011 20:50:33 +0000 (14:50 -0600)]
mmc: core: add workaround for controllers with broken multiblock reads
Due to hardware bugs, some MMC host controllers don't support
multiple-block reads[1]. To resolve, add a new MMC capability flag,
MMC_CAP2_NO_MULTI_READ, which can be set by affected host controller
drivers. When this capability is set, all reads will be issued one
sector at a time.
1. See for example Advisory 2.1.1.128 "MMC: Multiple Block Read
Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_
Revision F (October 2010) (SPRZ278F), available from
http://focus.ti.com/lit/er/sprz278f/sprz278f.pdf
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Dave Hylands <dhylands@gmail.com> Tested-by: Steve Sakoman <sakoman@gmail.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Ulf Hansson [Thu, 13 Oct 2011 14:03:58 +0000 (16:03 +0200)]
mmc: core: Prevent too long response times for suspend
While trying to suspend the mmc host there could still be
ongoing requests that we need to wait for. At the same time
a device driver must respond to a suspend request rather quickly.
Instead of potentially wait "forever" by claiming the host we now
"try" to claim the host instead. If it fails, -EBUSY is returned.
Subhash Jadavani [Wed, 10 Aug 2011 05:46:01 +0000 (11:16 +0530)]
mmc: sd: Handle SD3.0 cards not supporting UHS-I bus speed mode
Here is Essential conditions to indicate Version 3.00 Card
(SD_SPEC=2 and SD_SPEC3=1) :
(1) The card shall support CMD6
(2) The card shall support CMD8
(3) The card shall support CMD42
(4) User area capacity shall be up to 2GB (SDSC) or 32GB (SDHC)
User area capacity shall be more than or equal to 32GB and
up to 2TB (SDXC)
(5) Speed Class shall be supported (SDHC or SDXC)
So even if SD card doesn't support any of the newly defined
UHS-I bus speed mode, it can advertise itself as SD3.0 cards
as long as it supports all the essential conditions of
SD3.0 cards. Given this, these type of cards should atleast
run in High Speed mode @50MHZ if it supports HS.
But current initialization sequence for SD3.0 cards is
such that these non-UHS-I SD3.0 cards runs in Default
Speed mode @25MHz.
This patch makes sure that these non-UHS-I SD3.0 cards run
in High Speed Mode @50MHz.
Tested this patch with SanDisk Extreme SDHC 8GB Class 10 card.
Jaehoon Chung [Mon, 17 Oct 2011 10:36:23 +0000 (19:36 +0900)]
mmc: dw_mmc: modify DATA register offset
In dw_mmc 2.40a spec, Data register's offset is changed.
Before we used Data register offset 0x100. but if somebody uses a
2.40a controller, we must use 0x200 for Data register.
This patch adds a version-id checking point and uses SDMMC_DATA(x)
instead of SDMMC_DATA. It assumes 2.40a is the latest version.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Adrian Hunter [Fri, 6 May 2011 09:14:10 +0000 (12:14 +0300)]
mmc: omap_hsmmc: ensure pbias configuration is always done
Go through the driver's set_power() functions rather than
calling regulator_enable/disable() directly because otherwise
pbias configuration for MMC1 is not done.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Acked-by: Balaji T K <balajitk@ti.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Girish K S [Thu, 13 Oct 2011 06:34:16 +0000 (12:04 +0530)]
mmc: core: Add Power Off Notify Feature eMMC 4.5
This patch adds support for the power off notify feature, available in
eMMC 4.5 devices. If the host has support for this feature, then the
mmc core will notify the device by setting the POWER_OFF_NOTIFICATION
byte in the extended csd register with a value of 1 (POWER_ON).
For suspend mode short timeout is used, whereas for the normal poweroff
long timeout is used.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
EXT_CSD[248] includes the default maximum timeout for CMD6.
This field is added at eMMC4.5 Spec. And it can be used for default
timeout except for some operations which don't define the timeout
(i.e. background operation, sanitize, flush cache) in eMMC4.5 Spec.
Adrian Hunter [Mon, 3 Oct 2011 12:33:34 +0000 (15:33 +0300)]
mmc: sdhci-pci: add runtime pm support
Ths patch allows runtime PM for sdhci-pci, runtime suspending after
inactivity of 50ms and ensuring runtime resume before SDHC registers
are accessed. During runtime suspend, interrupts are masked.
The host controller state is restored at runtime resume.
For Medfield, the host controller's card detect mechanism is
supplanted by an always-on GPIO which provides for card detect wake-up.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Adrian Hunter [Mon, 3 Oct 2011 12:33:33 +0000 (15:33 +0300)]
mmc: core: move ->request() call from atomic context
mmc_request_done() is sometimes called from interrupt or other atomic
context. Mostly all mmc_request_done() does is complete(), however it
contains code to retry on error, which uses ->request(). As the error
path is certainly not performance critical, this may be moved to the
waiting function mmc_wait_for_req_done().
This allows ->request() to use runtime PM get_sync() and guarantee it
is never in an atomic context.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Ulf Hansson <ulf.hansson@stericsson.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Paul Gortmaker [Sun, 3 Jul 2011 19:15:51 +0000 (15:15 -0400)]
mmc: Add module.h to drivers/mmc users assuming implicit presence.
We are cleaning up the implicit presence of module.h; these guys are
some of the people who just assume it will be there. Call it out
explitly for those that really need it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: using module_param requires the inclusion of moduleparam.h
Commit "mmc: add module param to set fault injection attributes" adds
a module_param to this file. But it is relying on the old implicit
"module.h is everywhere" behaviour, and without the explicit include
of moduleparam.h, the pending module.h split up produces this error:
core/debugfs.c:28:35: error: expected ')' before numeric constant
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Namjae Jeon [Thu, 6 Oct 2011 14:41:38 +0000 (23:41 +0900)]
mmc: core: general purpose MMC partition support.
It allows gerneral purpose partitions in MMC Device. And I try to simply
make mmc_blk_alloc_parts using mmc_part structure suggested by Andrei
Warkentin. After patching, we see general purpose partitions like this:
> cat /proc/partitions
179 0 847872 mmcblk0
179 192 4096 mmcblk0gp3
179 160 4096 mmcblk0gp2
179 128 4096 mmcblk0gp1
179 96 1052672 mmcblk0gp0
179 64 1024 mmcblk0boot1
179 32 1024 mmcblk0boot0
Signed-off-by: Namjae Jeon <linkinjeon@gmail.com> Acked-by: Andrei Warkentin <awarkentin@vmware.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Andrei Warkentin [Sat, 24 Sep 2011 16:12:30 +0000 (12:12 -0400)]
mmc: core: ext_csd.raw_* used in comparison but never set
f39b2dd9d ("mmc: core: Bus width testing needs to handle suspend/resume")
added code to only compare read-only ext_csd fields in bus width testing
code, yet it's comparing some fields that are never set.
The affected fields are ext_csd.raw_erased_mem_count and
ext_csd.raw_partition_support.
Signed-off-by: Andrei Warkentin <andrey.warkentin@gmail.com> Acked-by: Philip Rakity <prakity@marvell.com> Cc: <stable@kernel.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts
disabled], we run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler returns with
interrupts enabled (see commit [b738a50a: genirq: Warn when handler
enables interrupts]).
Adrian Hunter [Fri, 23 Sep 2011 09:48:21 +0000 (12:48 +0300)]
mmc: block: support no access to boot partitions
Intel Medfield platform blocks access to eMMC boot partitions which
results in switch errors. Since there is no access, mmcboot0/1
devices should not be created. Add a host capability to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Adrian Hunter [Fri, 23 Sep 2011 09:48:20 +0000 (12:48 +0300)]
mmc: block: fix boot partition switch error path
In the case of a switch error, do not update partition config as though
the switch succeeded, and ensure blk_end_request is called on the
failed request.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Andrei Warkentin <andrey.warkentin@gmail.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Girish K S [Fri, 23 Sep 2011 15:11:47 +0000 (20:41 +0530)]
mmc: core: eMMC 4.5 Power Class Selection Feature
This patch adds the power class selection feature available for mmc
versions 4.0 and above. During the enumeration stage before switching
to the lower data bus, check if the power class is supported for the
current bus width. If the power class is available then switch to the
power class and use the higher data bus. If power class is not supported
then switch to the lower data bus in a worst case.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Per Forlin [Tue, 13 Sep 2011 21:03:29 +0000 (23:03 +0200)]
mmc: add module param to set fault injection attributes
Replace setup("fail_mmc_request") and faulty "ifdef KERNEL" with
a simple module_param(). The module param mmc_core.fail_request
may be used to set the fault injection attributes during boot time
or module load time.
Signed-off-by: Per Forlin <per.forlin@linaro.org> Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Adrian Hunter [Mon, 29 Aug 2011 13:42:15 +0000 (16:42 +0300)]
mmc: block: add eMMC hardware reset support
For cards that support hardware reset (just eMMC), try a reset and
retry before returning an I/O error. However this is not done for
ECC errors and is never done twice for the same operation type
(READ, WRITE, DISCARD, SECURE DISCARD) until that type of operation
again succeeds.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Adrian Hunter [Mon, 29 Aug 2011 13:42:11 +0000 (16:42 +0300)]
mmc: core: add eMMC hardware reset support
eMMC's may have a hardware reset line. This patch provides a
host controller operation to implement hardware reset and
a function to reset and reinitialize the card. Also, for MMC,
the reset is always performed before initialization.
The host must set the new host capability MMC_CAP_HW_RESET
to enable hardware reset.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Per Forlin [Mon, 29 Aug 2011 13:35:59 +0000 (15:35 +0200)]
mmc: mmci: simplify err check in mmci_post_request
The error condition indicates that mmci_post_request() should cleanup
after the mmci_pre_request(). In this case the resources allocated by
device_prep_slave_sg() are freed by calling dmaengine_terminate_all().
dma_unmap_sg() should always be performed if the host_cookie is set.
Signed-off-by: Per Forlin <per.forlin@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Per Forlin [Mon, 29 Aug 2011 13:35:58 +0000 (15:35 +0200)]
mmc: core: clarify how to use post_req in case of errors
The err condition in post_req() is set to undo a call made to pre_req()
that hasn't been started yet. The err condition is not set if an MMC
request returns an error.
Signed-off-by: Per Forlin <per.forlin@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Earlier all cards where initiated with bus mode set as OPENDRAIN, and then
later switched to PUSHPULL. According to the MMC/SD/SDIO specifications
only MMC cards use OPENDRAIN during init. For both SD and SDIO the bus
mode shall be PUSHPULL before attempting to init the card.
The consequence of having incorrect bus mode can lead to not being able
to detect the card. Therefore the default behavior have now been changed
to PUSHPULL in mmc_power_up, and will only be temporarily switched when
trying to attach or init a MMC card.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com> Signed-off-by: Ulf HANSSON <ulf.hansson@stericsson.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Adds a quirk which can be turned on for SDIO devices that do not support
512 byte requests in byte mode during CMD53. These requests will always
be sent in block mode instead.
This patch also enables this quirk for ST-Ericsson CW1200 WLAN device.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com> Signed-off-by: Ulf HANSSON <ulf.hansson@stericsson.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: core: Fix hangs related to insert/remove of cards
During a rescan operation mmc_attach(sd|mmc|sdio) functions are
called. The error handling in these function can trigger a detach
of the bus, which also meant a power off. This is not notified by
the rescan operation which then continues to the next attach function.
If a power off has been done, the framework must never send any
new commands to the host driver, without first doing a new power up.
This will most likely trigger any host driver to hang.
Moving power off out of detach and instead handle power off
separately when it is actually needed, solves the issue.
mmc: sdhci-spear: Don't set power gpio to 1 on probe
Currently if card_power_gpio is passed from platform data, it is acquired
and its value is either set or reset. After that we overwrite it with 1,
which is not required.
So, this patch removes the extra line which sets its value.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Xu lei [Fri, 9 Sep 2011 12:05:46 +0000 (20:05 +0800)]
mmc: sdhci-of-esdhc: Access Freescale eSDHC registers as 32-bit
Freescale eSDHC registers only support 32-bit accesses, this patch
ensures that all Freescale eSDHC register accesses are 32-bit.
Signed-off-by: Xu lei <B33228@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Anton Vorontsov <cbouatmailru@gmail.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Balaji T K [Thu, 8 Sep 2011 16:38:39 +0000 (22:08 +0530)]
mmc: core: Put eMMC in Sleep mode before suspend
Put MMC to sleep if it supports SLEEP/AWAKE (CMD5) in the mmc suspend
so that Vcc (NAND core) can be cut to minimize power consumption.
eMMC put into SLEEP can respond to CMD0 or H/W reset or CMD5.
Current implemention on resume from suspend relies on CMD0 in
mmc_init_card to get out of SLEEP mode.
Signed-off-by: Balaji T K <balajitk@ti.com> Acked-by: Venkatraman S <svenkatr@ti.com> Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Chris Ball <cjb@laptop.org>
The default controller configuration which was previously setup by
platform helper functions is moved into the driver.
Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Daniel Drake [Wed, 7 Sep 2011 09:22:09 +0000 (10:22 +0100)]
mmc: core: add a short delay in mmc_power_off
Stress-testing the runtime power management of libertas_sdio
through a rmmod/insmod loop revealed that it is quite easy to
cause an ETIMEDOUT failure in mmc_sdio_power_restore() leading to:
libertas_sdio: probe of mmc1:0001:1 failed with error -16
Experimentation shows that a very short delay (100us) is needed in
the power down path before the card can be successfully booted again.
We know that this setup is lacking poweroff clamps on the card's power
lines, but as only a short delay is needed, apply this unconditionally.
Also bump up to 1ms sleep for extra legroom.
Signed-off-by: Daniel Drake <dsd@laptop.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Stephen Warren [Tue, 30 Aug 2011 19:17:16 +0000 (13:17 -0600)]
mmc: sdhci-tegra: Add 8-bit support to device tree binding.
The previous patch which implemented a DT binding for sdhci-tegra did not
allow all platform data fields to be initialized from DT. The following
were missing:
is_8bit: Implemented by this patch.
pm_flags: Not implemented yet. There are no mainline users of this field.
I'm not quite sure what it's for, and hence how to represent this
in DT; the value ends up being assigned to host->mmc->pm_caps.
While we're at it, fix the binding documentation to refer to "SD/MMC"
instead of "eSDHC", since that's the correct name; "eSDHC" was cut/paste
from the Freescale binding docs.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: dw_mmc: Support SDIO interrupts for all slots
The Patch adds the support for SDIO interrupts for all slots.
It includes enabling of SDIO interrupts through dw_mci_enable_sdio_irq
and the handling of the slot specific interrupts in the Interrupt Service
Routine.
Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com> Acked-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Sahitya Tummala [Mon, 2 May 2011 12:39:18 +0000 (18:09 +0530)]
mmc: msm_sdcc: Use MCI_INT_MASK0 for PIO interrupts
Not all targets have IRQ1 line routed from the SD controller to
the processor. So we cannot rely on IRQ1 for PIO interrupts.
This patch moves all PIO interrupts to IRQ0 and enables the PIO
mode.
Signed-off-by: Murali Palnati <palnatim@codeaurora.org> Signed-off-by: Sahitya Tummala <stummala@codeaurora.org> Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Sahitya Tummala [Mon, 2 May 2011 12:37:43 +0000 (18:07 +0530)]
msm: mmc: Remove "pio_irq" resource
On some targets, MCI_IRQ_MASK1 is not routed to the MSM in which
case only "cmd_irq" must be used even for PIO. With this change,
all the targets will use only "cmd_irq" for both CMD and PIO.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org> Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Sahitya Tummala [Mon, 2 May 2011 12:37:01 +0000 (18:07 +0530)]
mmc: msm_sdcc: Enable SDC host->clk only after setting the rate.
For clocks that support rates which can be set (most clocks other
than _pclk AHB clocks), a rate must be set using clk_set_rate()
before the clock is enabled for the first time with clk_enable().
Subsequent calls to clk_enable() need not be preceded with the
clk_set_rate() calls unless we wish to change the clock rate that
is set previously.
SDC host->clk is currently enabled without setting the clock rate
even once. This patch fixes this, by ensuring that the clock rate
for this clock is first set before enabling the clock.
Signed-off-by: Murali Palnati <palnatim@codeaurora.org> Signed-off-by: Sahitya Tummala <stummala@codeaurora.org> Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Chris Ball <cjb@laptop.org>
This allows boards with non-standard sdio cards to fill the CIS/CCCR data.
It is particularly important for old msm72k boards using wl1251.
Also drop the obsolete embedded_sdio_data structure from the header
as it was intended to surve a similiar purpose but was not implemented.
Signed-off-by: Alexander Tarasikov <alexander.tarasikov@gmail.com> Acked-by: Sahitya Tummala <stummala@codeaurora.org>
[davidb: minor formatting cleanup] Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: msm_sdcc: Fix a typo in MSM SDCC driver gpio setup
The use of && instead of || caused a NULL pointer dereference if
gpio setup was not passed via platform data
Signed-off-by: Alexander Tarasikov <alexander.tarasikov@gmail.com> Acked-by: Sahitya Tummala <stummala@codeaurora.org> Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Simon Horman [Thu, 25 Aug 2011 01:27:28 +0000 (10:27 +0900)]
ARM: shmobile: ag5evm, ap4: Named SDHI IRQ sources
This allows specific (non-multiplexed) IRQ handlers to be used.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Cc: Paul Mundt <lethal@linux-sh.org> Acked-by: Magnus Damm <magnus.damm@gmail.com> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Chris Ball <cjb@laptop.org>
Simon Horman [Fri, 26 Aug 2011 08:42:39 +0000 (10:42 +0200)]
mmc: sdhi: Allow named IRQs to use specific handlers
Allow named IRQs to use corresponding specific handlers. If named IRQs are
used, at least an "sdcard" IRQ has to be specified by the platform. If
names are not used, an arbitrary number of IRQs can be provided by the
platform, in which case the generic ISR will be used for each of them.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Magnus Damm <magnus.damm@gmail.com> Signed-off-by: Simon Horman <horms@verge.net.au>
[g.liakhovetski@gmx.de: style and typo corrections, platform data check] Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Chris Ball <cjb@laptop.org>
The individual SoC dependency in Kconfig hardly scales anymore.
Instead of having such a fine grained dependency just depend
on ARCH_MXC and risk that the uninformed user has to look in
the help text to figure out which driver is the correct one.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Chris Ball <cjb@laptop.org>
Grant Likely [Tue, 23 Aug 2011 18:15:33 +0000 (12:15 -0600)]
mmc: sdhci-tegra: Add Device Tree probing support
Add hooks to read gpio configuration out of the device tree node.
[grant.likely: Rewrite of original patch from John Bonesio] Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
[swarren: Fixed tegra_sdhci_get_ro() to retrieve pdata correctly]
[swarren: Reworked to avoid #ifdef CONFIG_OF]
[swarren: Reworked binding based on fsl-imx-esdhc.txt]
[swarren: Documented binding] Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Daniel Drake [Wed, 20 Jul 2011 16:39:22 +0000 (17:39 +0100)]
mmc: enable runtime PM by default
Now that we have improved the runtime power management powerup/powerdown
code, we believe that MMC_CAP_POWER_OFF_CARD is no longer necessary:
runtime PM should now work everywhere.
The only hard evidence for introducing MMC_CAP_POWER_OFF_CARD was the
Marvell sd8686 wifi chip, which was believed to require external gpio
manipulation which wasn't supported by some boards.
After further investigation it was realized (and confirmed by Marvell
folks) that sd8686 requirements can be fulfilled by changing the reset
sequence itself, even if no external gpio is manipulated.
For further information, see the following thread:
http://www.mail-archive.com/linux-mmc@vger.kernel.org/msg04289.html
Enable this trivially for a release or two. If no problems are reported,
we will follow up with a more extensive patch to remove this flag
altogether. If problems are reported, we can look at whitelist/blacklist
possibilities as before.
Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Ohad Ben-Cohen <ohad@wizery.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Per Forlin [Fri, 19 Aug 2011 12:52:37 +0000 (14:52 +0200)]
mmc: core: add random fault injection
This adds support to inject data errors after a completed host transfer.
The mmc core will return error even though the host transfer is successful.
This simple fault injection proved to be very useful to test the
non-blocking error handling in the mmc_blk_issue_rw_rq().
Random faults can also test how the host driver handles pre_req()
and post_req() in case of errors.
Signed-off-by: Per Forlin <per.forlin@linaro.org> Acked-by: Akinobu Mita <akinobu.mita@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Nicolas Ferre [Thu, 4 Aug 2011 15:49:03 +0000 (16:49 +0100)]
mmc: at91_mci: remove the use of irq_to_gpio
Remove the use of irq_to_gpio() in the card detection interrupt
handler. The information is available in the board structure and
we can avoid using a function that has little meaning.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: atmel-mci: fix a potential issue about pending PDC interrupts
This patch fixes a potential issue about PDC interrupts. For example we
have a ENDRX pending interrupt and a RXBUFF pending interrupt. We have
received the RXBUFF interrupt but the transfer is not finished (so we
didn't have time to give a new buffer to the PDC controller). Then we
will compute ENDRX interrupt and we will give a new buffer to the PDC
controller, just after we will compute the RXBUFF interrupt and give
one or two new buffers to the PDC controller but we are not sure that
the first buffer given has been filled. So in this situation we may
have "lost" one sg buffer. It's the same for transmission.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: atmel-mci: add pdc support and runtime capabilities detection
Add pdc support for atmel-mci. It makes at91-mci driver useless because it
was only used for the old atmel MCI core which has pdc but no dma support.
To allow removing at91-mci, the capabilities of the MCI core are detected
at runtime -- then the driver will use pio, pdc or dma transfers.
Warning: at91rm9200 is not supported, to support it we need to use swab32
on data but I have no board to test it.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Chris Ball <cjb@laptop.org>
projects / karo-tx-linux.git / log