Alan Stern [Mon, 25 Jan 2016 20:45:38 +0000 (15:45 -0500)]
USB: EHCI: improvements to unlink_empty_async_suspended()
unlink_empty_async_suspended() is marked __maybe_unused. This is
because its caller, ehci_bus_suspend(), is protected by "#ifdef
CONFIG_PM". We should use the same protection here instead of
__maybe_unused.
unlink_empty_async_suspended() gets called only when the root hub is
suspended. It's silly for it to call start_iaa_cycle() at such a
time; the IAA mechanism doesn't work when the root hub isn't running.
It should call end_unlink_async() instead. But even this isn't
necessary, since there already is a call to end_iaa_cycle() right
before the call to unlink_empty_async_suspended(). All we have to do
is interchange the two subroutine calls.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Mon, 25 Jan 2016 20:45:25 +0000 (15:45 -0500)]
USB: EHCI: add a delay when unlinking an active QH
Michael Reutman reports that an AMD/ATI EHCI host controller on one of
his computers does not stop transferring data when an active bulk QH
is unlinked from the async schedule. Apparently that host controller
fails to implement the IAA mechanism correctly when an active QH is
unlinked. This leads to data corruption, because the controller
continues to update the QH in memory when the driver doesn't expect
it. As a result, the next URB submitted for that QH can hang, because
the link pointers for the TD queue have been messed up. This
misbehavior is observed quite regularly.
To be fair, the EHCI spec (section 4.8.2) says that active QHs should
not be unlinked. It goes on to recommend a procedure that involves
waiting for the QH to go inactive before unlinking it. In the real
world this is impractical, not least because the QH may _never_ go
inactive. (What were they thinking?) Sometimes we have no choice but
to unlink an active QH.
In an attempt to avoid the problems that can ensue, this patch changes
how the driver decides when the unlink is complete. In addition to
waiting through two IAA cycles, in cases where the QH was not known to
be inactive beforehand we now wait until a 2-ms period has elapsed
with the host controller making no change to the QH data structure
(the hw_current and hw_token fields in particular). The intuition
here is that after such a long period, the endpoint must be NAKing and
hopefully the QH has been dropped from the host controller's internal
cache. There's no way to know if this reasoning is really valid --
the spec is no help in this regard -- but at least this approach fixes
Michael's problem.
The test for whether the QH is already known to be inactive involves
the reason for unlinking the QH originally. If it was unlinked
because it had halted, or it stopped in response to a short read, or
it overlaid a dummy TD (a silicon bug), then it certainly is inactive.
If it was unlinked because the TD queue was empty and no TDs have been
added to the queue in the meantime, then it must be inactive. Or if
the hardware status indicates that the QH is currently halted (even if
that wasn't the reason for unlinking it), then it is inactive.
Otherwise, if none of those checks apply, we go through the 2-ms
delay.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Michael Reutman <mreutman@epiqsolutions.com> Tested-by: Michael Reutman <mreutman@epiqsolutions.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Mon, 25 Jan 2016 20:44:16 +0000 (15:44 -0500)]
USB: EHCI: improve handling of the ehci->iaa_in_progress flag
This patch improves the way ehci-hcd handles the iaa_in_progress flag.
The current code is somewhat careless in this regard:
The flag is meaningless when the root hub isn't running, most
particularly after the root hub has been suspended. But in
start_iaa_cycle(), the driver checks the flag before checking
the root hub's state. They should be checked in the opposite
order.
That routine also sets the flag too early, before it has
definitely committed to starting an IAA cycle.
The flag is turned off in end_unlink_async(). Upcoming
changes will call that routine at other times, not just at the
end of an IAA cycle. The two actions are logically separate
(although related), so we separate out a new routine to be
called in place of end_unlink_async() whenever an IAA cycle
ends: end_iaa_cycle().
iaa_in_progress should be turned off when the root hub is
suspended -- we certainly don't want it still to be set when
the root hub resumes. Therefore the call to
end_unlink_async() in ehci_bus_suspend() should also be
replaced with a call to end_iaa_cycle().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Mon, 25 Jan 2016 20:42:04 +0000 (15:42 -0500)]
USB: EHCI: store reason for unlinking a QH
This patch replaces the "exception" bitflag in the ehci_qh structure
with a more explicit "unlink_reason" bitmask. This is for use in the
following patch, where we will need to have a good idea of the
reason for unlinking a QH, not just "something exceptional happened".
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Michael Reutman <mreutman@epiqsolutions.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Mon, 1 Feb 2016 01:36:45 +0000 (17:36 -0800)]
Merge tag 'usb-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver fixes from Greg KH:
"Here are some small USB fixes and new device ids for 4.5-rc2. Nothing
major here, full details are in the shortlog, and all of these have
been in linux-next successfully"
* tag 'usb-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: option: fix Cinterion AHxx enumeration
USB: mxu11x0: fix memory leak on usb_serial private data
USB: serial: ftdi_sio: add support for Yaesu SCU-18 cable
USB: serial: option: Adding support for Telit LE922
USB: serial: visor: fix crash on detecting device without write_urbs
USB: visor: fix null-deref at probe
USB: cp210x: add ID for IAI USB to RS485 adaptor
usb: hub: do not clear BOS field during reset device
cdc-acm:exclude Samsung phone 04e8:685d
usb: cdc-acm: send zero packet for intel 7260 modem
usb: cdc-acm: handle unlinked urb in acm read callback
Linus Torvalds [Mon, 1 Feb 2016 01:09:39 +0000 (17:09 -0800)]
Merge tag 'tty-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty/serial driver fixes for 4.5-rc2.
They resolve a number of reported problems (the ioctl one specifically
has been pointed out by numerous people) and one patch adds some new
device ids for the 8250_pci driver. All have been in linux-next
successfully"
* tag 'tty-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250_pci: Add Intel Broadwell ports
staging/speakup: Use tty_ldisc_ref() for paste kworker
n_tty: Fix unsafe reference to "other" ldisc
tty: Fix unsafe ldisc reference via ioctl(TIOCGETD)
tty: Retry failed reopen if tty teardown in-progress
tty: Wait interruptibly for tty lock on reopen
Linus Torvalds [Mon, 1 Feb 2016 01:00:27 +0000 (17:00 -0800)]
Merge tag 'staging-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some small staging driver fixes for 4.5-rc2.
One of them predated 4.4-final, but I missed that merge window due to
the holliday. The others fix reported issues that have come up
recently. The tty change is needed for the speakup driver fix and has
the ack of the tty driver maintainer as well, i.e. myself :)
All have been in linux-next with no reported issues"
* tag 'staging-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Staging: speakup: fix read scrolled-back VT
Staging: speakup: Fix getting port information
Revert "Staging: panel: usleep_range is preferred over udelay"
iio: adis_buffer: Fix out-of-bounds memory access
Linus Torvalds [Mon, 1 Feb 2016 00:55:04 +0000 (16:55 -0800)]
Merge tag 'driver-core-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here's a single driver core fix that resolves an issue a lot of users
have been hitting for a while now. It's been tested a lot and has
been in linux-next successfully for a while"
* tag 'driver-core-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
base/platform: Fix platform drivers with no probe callback
Linus Torvalds [Mon, 1 Feb 2016 00:17:19 +0000 (16:17 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A bit on the largish side due to a series of fixes for a regression in
the x86 vector management which was introduced in 4.3. This work was
started in December already, but it took some time to fix all corner
cases and a couple of older bugs in that area which were detected
while at it
Aside of that a few platform updates for intel-mid, quark and UV and
two fixes for in the mm code:
- Use proper types for pgprot values to avoid truncation
- Prevent a size truncation in the pageattr code when setting page
attributes for large mappings"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
x86/mm/pat: Avoid truncation when converting cpa->numpages to address
x86/mm: Fix types used in pgprot cacheability flags translations
x86/platform/quark: Print boundaries correctly
x86/platform/UV: Remove EFI memmap quirk for UV2+
x86/platform/intel-mid: Join string and fix SoC name
x86/platform/intel-mid: Enable 64-bit build
x86/irq: Plug vector cleanup race
x86/irq: Call irq_force_move_complete with irq descriptor
x86/irq: Remove outgoing CPU from vector cleanup mask
x86/irq: Remove the cpumask allocation from send_cleanup_vector()
x86/irq: Clear move_in_progress before sending cleanup IPI
x86/irq: Remove offline cpus from vector cleanup
x86/irq: Get rid of code duplication
x86/irq: Copy vectormask instead of an AND operation
x86/irq: Check vector allocation early
x86/irq: Reorganize the search in assign_irq_vector
x86/irq: Reorganize the return path in assign_irq_vector
x86/irq: Do not use apic_chip_data.old_domain as temporary buffer
x86/irq: Validate that irq descriptor is still active
x86/irq: Fix a race in x86_vector_free_irqs()
...
Linus Torvalds [Sun, 31 Jan 2016 23:49:06 +0000 (15:49 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"The timer departement delivers:
- a regression fix for the NTP code along with a proper selftest
- prevent a spurious timer interrupt in the NOHZ lowres code
- a fix for user space interfaces returning the remaining time on
architectures with CONFIG_TIME_LOW_RES=y
- a few patches to fix COMPILE_TEST fallout"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/nohz: Set the correct expiry when switching to nohz/lowres mode
clocksource: Fix dependencies for archs w/o HAS_IOMEM
clocksource: Select CLKSRC_MMIO where needed
tick/sched: Hide unused oneshot timer code
kselftests: timers: Add adjtimex SETOFFSET validity tests
ntp: Fix ADJ_SETOFFSET being used w/ ADJ_NANO
itimers: Handle relative timers with CONFIG_TIME_LOW_RES proper
posix-timers: Handle relative timers with CONFIG_TIME_LOW_RES proper
timerfd: Handle relative timers with CONFIG_TIME_LOW_RES proper
hrtimer: Handle remaining time proper for TIME_LOW_RES
clockevents/tcb_clksrc: Prevent disabling an already disabled clock
Linus Torvalds [Sun, 31 Jan 2016 23:44:04 +0000 (15:44 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"Three small fixes in the scheduler/core:
- use after free in the numa code
- crash in the numa init code
- a simple spelling fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
pid: Fix spelling in comments
sched/numa: Fix use-after-free bug in the task_numa_compare
sched: Fix crash in sched_init_numa()
Linus Torvalds [Sun, 31 Jan 2016 23:38:27 +0000 (15:38 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"This is much bigger than typical fixes, but Peter found a category of
races that spurred more fixes and more debugging enhancements. Work
started before the merge window, but got finished only now.
Aside of that this contains the usual small fixes to perf and tools.
Nothing particular exciting"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (43 commits)
perf: Remove/simplify lockdep annotation
perf: Synchronously clean up child events
perf: Untangle 'owner' confusion
perf: Add flags argument to perf_remove_from_context()
perf: Clean up sync_child_event()
perf: Robustify event->owner usage and SMP ordering
perf: Fix STATE_EXIT usage
perf: Update locking order
perf: Remove __free_event()
perf/bpf: Convert perf_event_array to use struct file
perf: Fix NULL deref
perf/x86: De-obfuscate code
perf/x86: Fix uninitialized value usage
perf: Fix race in perf_event_exit_task_context()
perf: Fix orphan hole
perf stat: Do not clean event's private stats
perf hists: Fix HISTC_MEM_DCACHELINE width setting
perf annotate browser: Fix behaviour of Shift-Tab with nothing focussed
perf tests: Remove wrong semicolon in while loop in CQM test
perf: Synchronously free aux pages in case of allocation failure
...
Linus Torvalds [Sun, 31 Jan 2016 22:48:58 +0000 (14:48 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull IRQ fixes from Ingo Molnar:
"Mostly irqchip driver fixes, but also an irq core crash fix and a
build fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mxs: Add missing set_handle_irq()
irqchip/atmel-aic: Fix wrong bit operation for IRQ priority
irqchip/gic-v3-its: Recompute the number of pages on page size change
base: Export platform_msi_domain_[alloc,free]_irqs
of: MSI: Simplify irqdomain lookup
irqdomain: Allow domain lookup with DOMAIN_BUS_WIRED token
irqchip: Fix dependencies for archs w/o HAS_IOMEM
irqchip/s3c24xx: Mark init_eint as __maybe_unused
genirq: Validate action before dereferencing it in handle_irq_event_percpu()
Linus Torvalds [Sun, 31 Jan 2016 22:29:52 +0000 (14:29 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Here are two I2C driver regression fixes. piix4 gets a larger
overhaul fixing the latest refactoring and also an older known issue
as well. designware-pci gets a fix for a bad merge conflict
resolution"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: piix4: don't regress on bus names
i2c: designware-pci: use IRQF_COND_SUSPEND flag
i2c: piix4: Fully initialize SB800 before it is registered
i2c: piix4: Fix SB800 locking
Linus Torvalds [Sat, 30 Jan 2016 00:16:12 +0000 (16:16 -0800)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Just one fix for a -fstack-protector-strong problem from Kees Cook,
and adding the new copy_file_range syscall"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: wire up copy_file_range() syscall
ARM: 8500/1: fix atags_to_fdt with stack-protector-strong
Linus Torvalds [Sat, 30 Jan 2016 00:10:16 +0000 (16:10 -0800)]
Merge tag 'powerpc-4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Wire up copy_file_range() syscall from Chandan Rajendra
- Simplify module TOC handling from Alan Modra
- Remove newly added extra definition of pmd_dirty from Stephen Rothwell
- Allow user space to map rtas_rmo_buf from Vasant Hegde
- Fix PE location code from Gavin Shan
- Remove PPMU_HAS_SSLOT flag for Power8 from Madhavan Srinivasan
- Fixup _HPAGE_CHG_MASK from Aneesh Kumar K.V
* tag 'powerpc-4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fixup _HPAGE_CHG_MASK
powerpc/perf: Remove PPMU_HAS_SSLOT flag for Power8
powerpc/eeh: Fix PE location code
powerpc/mm: Allow user space to map rtas_rmo_buf
powerpc: Remove newly added extra definition of pmd_dirty
powerpc: Simplify module TOC handling
powerpc: Wire up copy_file_range() syscall
Linus Torvalds [Sat, 30 Jan 2016 00:05:18 +0000 (16:05 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
"An optimization for irq-restore, the SSM instruction is quite a bit
slower than an if-statement and a STOSM.
The copy_file_range system all is added.
Cleanup for PCI and CIO.
And a couple of bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cio: update measurement characteristics
s390/cio: ensure consistent measurement state
s390/cio: fix measurement characteristics memleak
s390/zcrypt: Fix cryptographic device id in kernel messages
s390/pci: remove iomap sanity checks
s390/pci: set error state for unusable functions
s390/pci: fix bar check
s390/pci: resize iomap
s390/pci: improve ZPCI_* macros
s390/pci: provide ZPCI_ADDR macro
s390/pci: adjust IOMAP_MAX_ENTRIES
s390/numa: move numa_init_late() from device to arch_initcall
s390: remove all usages of PSW_ADDR_INSN
s390: remove all usages of PSW_ADDR_AMODE
s390: wire up copy_file_range syscall
s390: remove superfluous memblock_alloc() return value checks
s390/numa: allocate memory with correct alignment
s390/irqflags: optimize irq restore
s390/mm: use TASK_MAX_SIZE where applicable
Linus Torvalds [Fri, 29 Jan 2016 23:46:49 +0000 (15:46 -0800)]
Merge branch 'for-linus-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Dave had a small collection of fixes to the new free space tree code,
one of which was keeping our sysfs files more up to date with feature
bits as different things get enabled (lzo, raid5/6, etc).
I should have kept the sysfs stuff for rc3, since we always manage to
trip over something. This time it was GFP_KERNEL from somewhere that
is NOFS only. Instead of rebasing it out I've put a revert in, and
we'll fix it properly for rc3.
Otherwise, Filipe fixed a btrfs DIO race and Qu Wenruo fixed up a
use-after-free in our tracepoints that Dave Jones reported"
* 'for-linus-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Revert "btrfs: synchronize incompat feature bits with sysfs files"
btrfs: don't use GFP_HIGHMEM for free-space-tree bitmap kzalloc
btrfs: sysfs: check initialization state before updating features
Revert "btrfs: clear PF_NOFREEZE in cleaner_kthread()"
btrfs: async-thread: Fix a use-after-free error for trace
Btrfs: fix race between fsync and lockless direct IO writes
btrfs: add free space tree to the cow-only list
btrfs: add free space tree to lockdep classes
btrfs: tweak free space tree bitmap allocation
btrfs: tests: switch to GFP_KERNEL
btrfs: synchronize incompat feature bits with sysfs files
btrfs: sysfs: introduce helper for syncing bits with sysfs files
btrfs: sysfs: add free-space-tree bit attribute
btrfs: sysfs: fix typo in compat_ro attribute definition
Linus Torvalds [Fri, 29 Jan 2016 23:40:59 +0000 (15:40 -0800)]
Merge tag 'pm+acpi-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are: cpuidle fixes (including one fix for a recent regression),
cpufreq fixes (including fixes for two issues introduced during the
4.2 cycle), generic power domains framework fixes (two locking fixes
and one cleanup), one locking fix in the ACPI-based PCI hotplug
framework (ACPIPHP), removal of one ACPI backlight blacklist entry
that isn't necessary any more and a PM Kconfig cleanup.
Specifics:
- Fix a recent cpuidle core regression that broke suspend-to-idle on
all systems where cpuidle drivers don't provide ->enter_freeze
callbacks for any states (Sudeep Holla).
- Drop an unnecessary symbol definition from the cpuidle core code
handling coupled CPU cores (Anders Roxell).
- Fix a race condition related to governor initialization and removal
in the cpufreq core (Viresh Kumar).
- Clean up the cpufreq core to use list_is_last() for checking if the
given policy object is the last element of a list instead of open
coding that in a clumsy way (Gautham R Shenoy).
- Fix compiler warnings in the pxa2xx and cpufreq-dt cpufreq drivers
(Arnd Bergmann).
- Fix two locking issues and clean up a comment in the generic power
domains framework (Ulf Hansson, Marek Szyprowski, Moritz Fischer).
- Fix the error code path of one function in the ACPI-based PCI
hotplug framework (ACPIPHP) that forgets to release a lock acquired
previously (Insu Yun).
- Drop the ACPI backlight blacklist entry for Dell Inspiron 5737 that
is not necessary any more (Hans de Goede).
- Clean up the top-level PM Kconfig to stop requiring APM emulation
to depend on PM which in fact isn't necessary (Arnd Bergmann)"
* tag 'pm+acpi-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: cpufreq-dt: avoid uninitialized variable warnings:
cpufreq: pxa2xx: fix pxa_cpufreq_change_voltage prototype
PM: APM_EMULATION does not depend on PM
cpufreq: Use list_is_last() to check last entry of the policy list
cpufreq: Fix NULL reference crash while accessing policy->governor_data
cpuidle: coupled: remove unused define cpuidle_coupled_lock
PM / Domains: Fix typo in comment
PM / Domains: Fix potential deadlock while adding/removing subdomains
ACPI / PCI / hotplug: unlock in error path in acpiphp_enable_slot()
ACPI: Revert "ACPI / video: Add Dell Inspiron 5737 to the blacklist"
cpuidle: fix fallback mechanism for suspend to idle in absence of enter_freeze
PM / domains: fix lockdep issue for all subdomains
Linus Torvalds [Fri, 29 Jan 2016 23:19:42 +0000 (15:19 -0800)]
Merge branch 'stable/for-linus-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb
Pull swiotlb patchlet from Konrad Rzeszutek Wilk:
"One trivial patch.
Another patch (from Fengguang) is already in your tree courtesy of
Andrew Morton - but I would prefer not to rebase my tree. Hence the
diff is very small"
* 'stable/for-linus-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb: Make linux/swiotlb.h standalone includible
MAINTAINERS: add git URL for swiotlb
Linus Torvalds [Fri, 29 Jan 2016 23:05:49 +0000 (15:05 -0800)]
Merge tag 'iommu-fixes-v4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"Five patches queued up:
- Two patches for the AMD and Intel IOMMU drivers to fix alias
handling and ATS handling.
- Fix build error with arm io-pgtable code
- Two documentation fixes"
* tag 'iommu-fixes-v4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu: Update struct iommu_ops comments
iommu/vt-d: Fix link to Intel IOMMU Specification
iommu/amd: Correct the wrong setting of alias DTE in do_attach
iommu/vt-d: Don't skip PCI devices when disabling IOTLB
iommu/io-pgtable-arm: Fix io-pgtable-arm build failure
Linus Torvalds [Fri, 29 Jan 2016 21:20:39 +0000 (13:20 -0800)]
Merge tag 'hwmon-for-linus-v4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Use bit mask to calculate tdp limit in fam15h_power driver
- Black-list Dell Studio XPS 8000 in dell-smm driver
* tag 'hwmon-for-linus-v4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (fam15h_power) Add bit masking for tdp_limit
hwmon: (dell-smm) Blacklist Dell Studio XPS 8000
Linus Torvalds [Fri, 29 Jan 2016 21:14:45 +0000 (13:14 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four fixes: one to try to fix our repeated intermittent crashes in
suspend/resume, one to correct a regression in the optimal I/O size
reporting and a couple for randconfig build failures in the hisi_sas
driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
SCSI: fix crashes in sd and sr runtime PM
sd: Optimal I/O size is in bytes, not sectors
hisi_sas: Restrict SCSI_HISI_SAS to arm64
hisi_sas: SCSI_HISI_SAS should depend on HAS_DMA
Merge branches 'pm-cpuidle', 'pm-cpufreq', 'pm-domains' and 'pm-sleep'
* pm-cpuidle:
cpuidle: coupled: remove unused define cpuidle_coupled_lock
cpuidle: fix fallback mechanism for suspend to idle in absence of enter_freeze
* pm-cpufreq:
cpufreq: cpufreq-dt: avoid uninitialized variable warnings:
cpufreq: pxa2xx: fix pxa_cpufreq_change_voltage prototype
cpufreq: Use list_is_last() to check last entry of the policy list
cpufreq: Fix NULL reference crash while accessing policy->governor_data
* pm-domains:
PM / Domains: Fix typo in comment
PM / Domains: Fix potential deadlock while adding/removing subdomains
PM / domains: fix lockdep issue for all subdomains
* pm-sleep:
PM: APM_EMULATION does not depend on PM
Linus Torvalds [Fri, 29 Jan 2016 20:34:39 +0000 (12:34 -0800)]
Merge tag 'sound-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"There are a few fixes in ALSA core for bugs that have been spotted by
fuzzer. Also a temporary workaround for PowerPC (and possibly other)
builds with incompatible ioctls was applied to compress API.
Other than that, a few trivial fixes and quirks for FireWire BeBoB,
USB-audio and HD-audio are found, too"
* tag 'sound-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - disable dynamic clock gating on Broxton before reset
ALSA: hda - Add new GPU codec ID 0x10de0083 to snd-hda
ALSA: dummy: Disable switching timer backend via sysfs
ALSA: timer: fix SND_PCM_TIMER Kconfig text
ALSA: Add missing dependency on CONFIG_SND_TIMER
ALSA: bebob: Use a signed return type for get_formation_index
ALSA: usb-audio: Fix TEAC UD-501/UD-503/NT-503 usb delay
ALSA: compress: Disable GET_CODEC_CAPS ioctl for some architectures
ALSA: seq: Degrade the error message for too many opens
ALSA: seq: Fix incorrect sanity check at snd_seq_oss_synth_cleanup()
The etnaviv guys had an API feature they wanted in their first
release, so I've merged that with their fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (41 commits)
drm/vmwgfx: respect 'nomodeset'
drm/amdgpu: only move pt bos in LRU list on success
drm/radeon: fix DP audio support for APU with DCE4.1 display engine
drm/radeon: Add a common function for DFS handling
drm/radeon: cleaned up VCO output settings for DP audio
drm/amd/powerplay: Update SMU firmware loading for Stoney
drm/etnaviv: call correct function when trying to vmap a DMABUF
drm/etnaviv: rename etnaviv_gem_vaddr to etnaviv_gem_vmap
drm/etnaviv: fix get pages error path in etnaviv_gem_vaddr
drm/etnaviv: fix memory leak in IOMMU init path
drm/etnaviv: add further minor features and varyings count
drm/etnaviv: add helper for comparing model/revision IDs
drm/etnaviv: add helper to extract bitfields
drm/etnaviv: use defined constants for the chip model
drm/etnaviv: update common and state_hi xml.h files
drm/etnaviv: ignore VG GPUs with FE2.0
drm/amdgpu: don't init fbdev if we don't have any connectors
drm/radeon: only init fbdev if we have connectors
drm/radeon: Ensure radeon bo is unreserved in radeon_gem_va_ioctl
drm/etnaviv: fix failure path if model is zero
...
Linus Torvalds [Fri, 29 Jan 2016 20:24:05 +0000 (12:24 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security layer fixes from James Morris:
"The keys patch fixes a bug which is breaking kerberos, and the seccomp
fix addresses a no_new_privs bypass"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
KEYS: Only apply KEY_FLAG_KEEP to a key if a parent keyring has it set
seccomp: always propagate NO_NEW_PRIVS on tsync
This ends up doing sysfs operations from deep in balance (where we
should be GFP_NOFS) and under heavy balance load, we're making races
against sysfs internals.
Mika Westerberg [Fri, 29 Jan 2016 14:49:47 +0000 (16:49 +0200)]
serial: 8250_pci: Add Intel Broadwell ports
Some recent (early 2015) macbooks have Intel Broadwell where LPSS UARTs are
PCI enumerated instead of ACPI. The LPSS UART block is pretty much same as
used on Intel Baytrail so we can reuse the existing Baytrail setup code.
Add both Broadwell LPSS UART ports to the list of supported devices.
Signed-off-by: Leif Liddy <leif.liddy@gmail.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matt Fleming [Fri, 29 Jan 2016 11:36:10 +0000 (11:36 +0000)]
x86/mm/pat: Avoid truncation when converting cpa->numpages to address
There are a couple of nasty truncation bugs lurking in the pageattr
code that can be triggered when mapping EFI regions, e.g. when we pass
a cpa->pgd pointer. Because cpa->numpages is a 32-bit value, shifting
left by PAGE_SHIFT will truncate the resultant address to 32-bits.
Viorel-Cătălin managed to trigger this bug on his Dell machine that
provides a ~5GB EFI region which requires 1236992 pages to be mapped.
When calling populate_pud() the end of the region gets calculated
incorrectly in the following buggy expression,
end = start + (cpa->numpages << PAGE_SHIFT);
And only 188416 pages are mapped. Next, populate_pud() gets invoked
for a second time because of the loop in __change_page_attr_set_clr(),
only this time no pages get mapped because shifting the remaining
number of pages (1048576) by PAGE_SHIFT is zero. At which point the
loop in __change_page_attr_set_clr() spins forever because we fail to
map progress.
Hitting this bug depends very much on the virtual address we pick to
map the large region at and how many pages we map on the initial run
through the loop. This explains why this issue was only recently hit
with the introduction of commit
a5caa209ba9c ("x86/efi: Fix boot crash by mapping EFI memmap
entries bottom-up at runtime, instead of top-down")
It's interesting to note that safe uses of cpa->numpages do exist in
the pageattr code. If instead of shifting ->numpages we multiply by
PAGE_SIZE, no truncation occurs because PAGE_SIZE is a UL value, and
so the result is unsigned long.
To avoid surprises when users try to convert very large cpa->numpages
values to addresses, change the data type from 'int' to 'unsigned
long', thereby making it suitable for shifting by PAGE_SHIFT without
any type casting.
The alternative would be to make liberal use of casting, but that is
far more likely to cause problems in the future when someone adds more
code and fails to cast properly; this bug was difficult enough to
track down in the first place.
Libin Yang [Fri, 29 Jan 2016 12:39:09 +0000 (20:39 +0800)]
ALSA: hda - disable dynamic clock gating on Broxton before reset
On Broxton, to make sure the reset controller works properly,
MISCBDCGE bit (bit 6) in CGCTL (0x48) of PCI configuration space
need be cleared before reset and set back to 1 after reset.
Otherwise, it may prevent the CORB/RIRB logic from being reset.
Baoquan He [Wed, 20 Jan 2016 14:01:19 +0000 (22:01 +0800)]
iommu/amd: Correct the wrong setting of alias DTE in do_attach
In below commit alias DTE is set when its peripheral is
setting DTE. However there's a code bug here to wrongly
set the alias DTE, correct it in this patch.
Oleksij Rempel [Fri, 29 Jan 2016 09:57:53 +0000 (10:57 +0100)]
irqchip/mxs: Add missing set_handle_irq()
The rework of the driver missed to move the call to set_handle_irq() into
asm9260_of_init(). As a consequence no interrupt entry point is installed and
no interrupts are delivered
Solution is simple: Install the interrupt entry handler.
Trying to build a kernel for ARC with both options CONFIG_COMPILE_TEST
and CONFIG_IOMMU_IO_PGTABLE_LPAE enabled (e.g. as a result of "make
allyesconfig") results in the following build failure:
| CC drivers/iommu/io-pgtable-arm.o
| linux/drivers/iommu/io-pgtable-arm.c: In
| function ‘__arm_lpae_alloc_pages’:
| linux/drivers/iommu/io-pgtable-arm.c:221:3:
| error: implicit declaration of function ‘dma_map_single’
| [-Werror=implicit-function-declaration]
| dma = dma_map_single(dev, pages, size, DMA_TO_DEVICE);
| ^
| linux/drivers/iommu/io-pgtable-arm.c:221:42:
| error: ‘DMA_TO_DEVICE’ undeclared (first use in this function)
| dma = dma_map_single(dev, pages, size, DMA_TO_DEVICE);
| ^
Since IOMMU_IO_PGTABLE_LPAE depends on DMA API, io-pgtable-arm.c should
include linux/dma-mapping.h. This fixes the reported failure.
Jean Delvare [Wed, 27 Jan 2016 13:40:33 +0000 (14:40 +0100)]
i2c: piix4: don't regress on bus names
The I2C bus names are supposed to be stable as they can be used by
userspace to uniquely identify a specific I2C bus. So restore the
original names for all legacy (pre-SB800) devices.
For SB800 devices and later, improve the names. "SDA" refers to the
serial data pin of each SMBus port, it's an implementation detail the
user doesn't need to know. Use "port" instead, which is easier to
understand.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Tested-by: Christian Fetzer <fetzer.ch@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Peter Zijlstra [Tue, 26 Jan 2016 14:25:15 +0000 (15:25 +0100)]
perf: Remove/simplify lockdep annotation
Now that the perf_event_ctx_lock_nested() call has moved from
put_event() into perf_event_release_kernel() the first reason is no
longer valid as that can no longer happen.
The second reason seems to have been invalidated when Al Viro made fput()
unconditionally async in the following commit:
Peter Zijlstra [Fri, 15 Jan 2016 14:07:41 +0000 (16:07 +0200)]
perf: Synchronously clean up child events
The orphan cleanup workqueue doesn't always catch orphans, for example,
if they never schedule after they are orphaned. IOW, the event leak is
still very real. It also wouldn't work for kernel counters.
Doing it synchonously is a little hairy due to lock inversion issues,
but is made to work.
Patch based on work by Alexander Shishkin.
Suggested-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: David Ahern <dsahern@gmail.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: vince@deater.net Signed-off-by: Ingo Molnar <mingo@kernel.org>
Peter Zijlstra [Tue, 26 Jan 2016 13:55:02 +0000 (14:55 +0100)]
perf: Untangle 'owner' confusion
There are two concepts of owner wrt an event and they are conflated:
- event::owner / event::owner_list,
used by prctl(.option = PR_TASK_PERF_EVENTS_{EN,DIS}ABLE).
- the 'owner' of the event object, typically the file descriptor.
Currently these two concepts are conflated, which gives trouble with
scm_rights passing of file descriptors. Passing the event and then
closing the creating task would render the event 'orphan' and would
have it cleared out. Unlikely what is expectd.
This patch untangles these two concepts by using PERF_EVENT_STATE_EXIT
to denote the second type.
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: David Ahern <dsahern@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Signed-off-by: Ingo Molnar <mingo@kernel.org>
Peter Zijlstra [Tue, 26 Jan 2016 12:06:56 +0000 (13:06 +0100)]
perf: Clean up sync_child_event()
sync_child_event() has outgrown its purpose, it does far too much.
Bring it back to its named purpose.
Rename __perf_event_exit_task() to perf_event_exit_event() to better
reflect what it does and move the event->state assignment under the
ctx->lock, like state changes ought to be.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: David Ahern <dsahern@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Signed-off-by: Ingo Molnar <mingo@kernel.org>
Peter Zijlstra [Wed, 27 Jan 2016 22:24:29 +0000 (23:24 +0100)]
perf/x86: Fix uninitialized value usage
When calling intel_alt_er() with .idx != EXTRA_REG_RSP_* we will not
initialize alt_idx and then use this uninitialized value to index an
array.
When that is not fatal, it can result in an infinite loop in its
caller __intel_shared_reg_get_constraints(), with IRQs disabled.
Alternative error modes are random memory corruption due to the
cpuc->shared_regs->regs[] array overrun, which manifest in either
get_constraints or put_constraints doing weird stuff.
Only took 6 hours of painful debugging to find this. Neither GCC nor
Smatch warnings flagged this bug.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: David Ahern <dsahern@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kan Liang <kan.liang@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Fixes: ae3f011fc251 ("perf/x86/intel: Fix SLM MSR_OFFCORE_RSP1 valid_mask") Signed-off-by: Ingo Molnar <mingo@kernel.org>
Samuel Thibault [Mon, 25 Jan 2016 00:32:08 +0000 (01:32 +0100)]
Staging: speakup: fix read scrolled-back VT
Previously, speakup would always read the non-scrolled part of the VT,
even when the VT is scrolled back with shift-page. This patch makes
vt.c export screen_pos so that speakup can use it to properly access
the content of the scrolled-back VT.
This was tested with both vgacon and fbcon.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Reviewed-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Samuel Thibault [Thu, 14 Jan 2016 23:47:41 +0000 (00:47 +0100)]
Staging: speakup: Fix getting port information
Commit f79b0d9c223c ("staging: speakup: Fixed warning <linux/serial.h>
instead of <asm/serial.h>") broke the port information in the speakup
driver: SERIAL_PORT_DFNS only gets defined if asm/serial.h is included,
and no other header includes asm/serial.h.
We here make sure serialio.c does get the arch-specific definition of
SERIAL_PORT_DFNS from asm/serial.h, if any.
Along the way, this makes sure that we do have information for the
requested serial port number (index)
Linus Torvalds [Fri, 29 Jan 2016 01:00:50 +0000 (17:00 -0800)]
Merge tag 'trace-v4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull minor tracing fixes from Steven Rostedt:
"This includes three minor fixes, mostly due to cut-and-paste issues.
The first is a cut and paste issue that changed the amount of stack to
skip when tracing a stack dump from 0 to 6, which basically made the
stack disappear for small stack traces.
The second fix is just removing an unused field in a struct that is no
longer used, and currently just wastes space.
The third is another cut-and-paste fix that had a tracepoint recording
the wrong field (it was recording the previous field a second time)"
* tag 'trace-v4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/dma-buf/fence: Fix timeline str value on fence_annotate_wait_on
ftrace: Remove unused nr_trampolines var
tracing: Fix stacktrace skip depth in trace_buffer_unlock_commit_regs()
Dave Airlie [Fri, 29 Jan 2016 00:04:29 +0000 (10:04 +1000)]
Merge branch 'drm-rockchip-next-fixes-2016-01-22' of https://github.com/markyzq/kernel-drm-rockchip into drm-fixes
Here are some fixes for drm/rockchip, these fixes base on drm-next.
These fixes works on my popmetal(rk3288) board.
About patch: drm/atomic-helper: Export framebuffer_changed()
Daniel Vetter ack for merging it through rockchip git trees, so framebuffer_changed() can be reused by drm/rockchip.
All others looks good, so I'd like you can land them.
* 'drm-rockchip-next-fixes-2016-01-22' of https://github.com/markyzq/kernel-drm-rockchip:
drm/rockchip: respect CONFIG_DRM_FBDEV_EMULATION
drm/rockchip: fix wrong pitch/size using on gem
drm/rockchip: explain why we can't wait_for_vblanks
drm/rockchip: don't wait for vblank if fb hasn't changed
drm/atomic-helper: Export framebuffer_changed()
drm/rockchip/dsi: fix handling mipi_dsi_pixel_format_to_bpp result
drm/rockchip: vop: fix mask when updating interrupts
drm/rockchip: cleanup unnecessary export symbol
drm/rockchip: Don't build rockchip_drm_vop as modules
Rob Clark [Wed, 15 Oct 2014 19:00:47 +0000 (15:00 -0400)]
drm/vmwgfx: respect 'nomodeset'
Signed-off-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>. Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 29 Jan 2016 00:01:54 +0000 (10:01 +1000)]
Merge branch 'drm-etnaviv-fixes' of git://git.pengutronix.de/git/lst/linux into drm-fixes
A bunch of etnaviv fixes for 4.5-rc. Most of them are fixing
things in code paths that will only be hit if something goes
wrong, which have been unearthed by more extensive testing.
The only thing that doesn't really qualify as fixes is an UAPI
extension that userspace wants to rely on being present, so
I want to fast-track this into 4.5 before etnaviv ends up in a
released kernel.
* 'drm-etnaviv-fixes' of git://git.pengutronix.de/git/lst/linux:
drm/etnaviv: call correct function when trying to vmap a DMABUF
drm/etnaviv: rename etnaviv_gem_vaddr to etnaviv_gem_vmap
drm/etnaviv: fix get pages error path in etnaviv_gem_vaddr
drm/etnaviv: fix memory leak in IOMMU init path
drm/etnaviv: add further minor features and varyings count
drm/etnaviv: add helper for comparing model/revision IDs
drm/etnaviv: add helper to extract bitfields
drm/etnaviv: use defined constants for the chip model
drm/etnaviv: update common and state_hi xml.h files
drm/etnaviv: ignore VG GPUs with FE2.0
drm/etnaviv: fix failure path if model is zero
drm/etnaviv: hold object lock while getting pages for coredump
drm/etnaviv: remove owner assignment from platform_driver
Dave Airlie [Fri, 29 Jan 2016 00:00:45 +0000 (10:00 +1000)]
Merge branch 'drm-fixes-4.5' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Misc radeon and amdgpu fixes:
- SMU firmware loading fix for Stoney
- DP audio fixes for DCE4.1
- Don't expose fbdev device if no connectors
- fix page table LRU list update handling
* 'drm-fixes-4.5' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: only move pt bos in LRU list on success
drm/radeon: fix DP audio support for APU with DCE4.1 display engine
drm/radeon: Add a common function for DFS handling
drm/radeon: cleaned up VCO output settings for DP audio
drm/amd/powerplay: Update SMU firmware loading for Stoney
drm/amdgpu: don't init fbdev if we don't have any connectors
drm/radeon: only init fbdev if we have connectors
drm/radeon: Ensure radeon bo is unreserved in radeon_gem_va_ioctl
drm/amdgpu: fix next_rptr handling for debugfs
drm/radeon: properly byte swap vce firmware setup
drm/amdgpu: add a message to indicate when powerplay is enabled (v2)
drm/amdgpu: fix amdgpu_bo_pin_restricted VRAM placing v2
drm/amd/amdgpu: Improve amdgpu_dpm* macros to avoid unexpected result (v2)
drm/amdgpu: Allow the driver to load if amdgpu.powerplay=1 on asics without powerplay support
drm/amdgpu: Use drm_calloc_large for VM page_tables array
drm/amdgpu: Add some tweaks to gfx 8 soft reset
drm/amdgpu: fix tonga smu resume
Peter Zijlstra [Mon, 25 Jan 2016 13:09:54 +0000 (14:09 +0100)]
perf: Fix race in perf_event_exit_task_context()
There is a race between perf_event_exit_task_context() and
orphans_remove_work() which results in a use-after-free.
We mark ctx->task with TASK_TOMBSTONE to indicate a context is
'dead', under ctx->lock. After which point event_function_call()
on any event of that context will NOP
A concurrent orphans_remove_work() will only hold ctx->mutex for
the list iteration and not serialize against this. Therefore its
possible that orphans_remove_work()'s perf_remove_from_context()
call will fail, but we'll continue to free the event, with the
result of free'd memory still being on lists and everything.
Once perf_event_exit_task_context() gets around to acquiring
ctx->mutex it too will iterate the event list, encounter the
already free'd event and proceed to free it _again_. This fails
with the WARN in free_event().
Plug the race by having perf_event_exit_task_context() hold
ctx::mutex over the whole tear-down, thereby 'naturally'
serializing against all other sites, including the orphan work.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: alexander.shishkin@linux.intel.com Cc: dsahern@gmail.com Cc: namhyung@kernel.org Link: http://lkml.kernel.org/r/20160125130954.GY6357@twins.programming.kicks-ass.net Signed-off-by: Ingo Molnar <mingo@kernel.org>
Peter Zijlstra [Mon, 25 Jan 2016 13:08:45 +0000 (14:08 +0100)]
perf: Fix orphan hole
We should set event->owner before we install the event,
otherwise there is a hole where the target task can fork() and
we'll not inherit the event because it thinks the event is
orphaned.
Signed-off-by: Peter Zijlstra <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Nicolai Hähnle [Wed, 27 Jan 2016 16:04:19 +0000 (11:04 -0500)]
drm/amdgpu: only move pt bos in LRU list on success
This fixes a race condition in the error case: since the pt bos have not
necessarily been reserved in case of an error, we could move a pt bo that
is currently in the middle of being evicted/moved by another process,
which then resulted in a BUG_ON in ttm_bo_add_to_lru.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Merge tag 'usb-serial-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.5-rc2
Here are two fixes of crashes in the visor driver that could be
triggered using bad (malicious) descriptors, a fix for two memory leaks
in the new mxu11x0 driver, and an interface-blacklist fix for the option
driver.
This was wrongly updated by commit 7aa9a23c69ea ("powerpc, thp: remove
infrastructure for handling splitting PMDs") during the last merge
window. Fix it up.
This could lead to incorrect behaviour in THP and/or mprotect(), at a
minimum.
Fixes: 7aa9a23c69ea ("powerpc, thp: remove infrastructure for handling splitting PMDs") Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/perf: Remove PPMU_HAS_SSLOT flag for Power8
Commit 7a7868326d77 ("powerpc/perf: Add an explict flag indicating
presence of SLOT field") introduced the PPMU_HAS_SSLOT flag to remove
the assumption that MMCRA[SLOT] was present when PPMU_ALT_SIPR was not
set.
That commit's changelog also mentions that Power8 does not support
MMCRA[SLOT]. However when the Power8 PMU support was merged, it
errnoeously included the PPMU_HAS_SSLOT flag.
So remove PPMU_HAS_SSLOT from the Power8 flags.
mpe: On systems where MMCRA[SLOT] exists, the field occupies bits 37:39
(IBM numbering). On Power8 bit 37 is reserved, and 38:39 overlap with
the high bits of the Threshold Event Counter Mantissa. I am not aware of
any published events which use the threshold counting mechanism, which
would cause the mantissa bits to be set. So in practice this bug is
unlikely to trigger.
Takashi Iwai [Thu, 28 Jan 2016 06:54:16 +0000 (07:54 +0100)]
ALSA: dummy: Disable switching timer backend via sysfs
ALSA dummy driver can switch the timer backend between system timer
and hrtimer via its hrtimer module option. This can be also switched
dynamically via sysfs, but it may lead to a memory corruption when
switching is done while a PCM stream is running; the stream instance
for the newly switched timer method tries to access the memory that
was allocated by another timer method although the sizes differ.
As the simplest fix, this patch just disables the switch via sysfs by
dropping the writable bit.
to undo the change that made it unconditional (Mimi got it right the first
time).
Without undoing this change, it becomes impossible to delete, revoke or
invalidate keys added to keyrings through __key_instantiate_and_link()
where the keyring has itself been linked to. To test this, run the
following command sequence:
keyctl newring foo @s
keyctl add user a a %:foo
keyctl unlink %user:a %:foo
keyctl clear %:foo
With the commit mentioned above the third and fourth commands fail with
EPERM when they should succeed.
Reported-by: Stephen Gallager <sgallagh@redhat.com> Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
cc: keyrings@vger.kernel.org
cc: stable@vger.kernel.org Signed-off-by: James Morris <james.l.morris@oracle.com>
gcc warns quite a bit about values returned from allocate_resources()
in cpufreq-dt.c:
cpufreq-dt.c: In function 'cpufreq_init':
cpufreq-dt.c:327:6: error: 'cpu_dev' may be used uninitialized in this function [-Werror=maybe-uninitialized]
cpufreq-dt.c:197:17: note: 'cpu_dev' was declared here
cpufreq-dt.c:376:2: error: 'cpu_clk' may be used uninitialized in this function [-Werror=maybe-uninitialized]
cpufreq-dt.c:199:14: note: 'cpu_clk' was declared here
cpufreq-dt.c: In function 'dt_cpufreq_probe':
cpufreq-dt.c:461:2: error: 'cpu_clk' may be used uninitialized in this function [-Werror=maybe-uninitialized]
cpufreq-dt.c:447:14: note: 'cpu_clk' was declared here
The problem is that it's slightly hard for gcc to follow return
codes across PTR_ERR() calls.
This patch uses explicit assignments to the "ret" variable to make
it easier for gcc to verify that the code is actually correct,
without the need to add a bogus initialization.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are two definitions of pxa_cpufreq_change_voltage, with slightly
different prototypes after one of them had its argument marked 'const'.
Now the other one (for !CONFIG_REGULATOR) produces a harmless warning:
drivers/cpufreq/pxa2xx-cpufreq.c: In function 'pxa_set_target':
drivers/cpufreq/pxa2xx-cpufreq.c:291:36: warning: passing argument 1 of 'pxa_cpufreq_change_voltage' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
ret = pxa_cpufreq_change_voltage(&pxa_freq_settings[idx]);
^
drivers/cpufreq/pxa2xx-cpufreq.c:205:12: note: expected 'struct pxa_freqs *' but argument is of type 'const struct pxa_freqs *'
static int pxa_cpufreq_change_voltage(struct pxa_freqs *pxa_freq)
^
This changes the prototype in the same way as the other, which
avoids the warning.
Fixes: 03c229906311 (cpufreq: pxa: make pxa_freqs arrays const) Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: 4.2+ <stable@vger.kernel.org> # 4.2+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Arnd Bergmann [Mon, 25 Jan 2016 15:48:28 +0000 (16:48 +0100)]
PM: APM_EMULATION does not depend on PM
The APM emulation code does multiple things, and some of them depend on
PM_SLEEP, while the battery management does not. However, selecting
the symbol like SHARPSL_PM does causes a Kconfig warning:
warning: (SHARPSL_PM && PMAC_APM_EMU) selects APM_EMULATION which has unmet direct dependencies (PM && SYS_SUPPORTS_APM_EMULATION)
From all I can tell, this is completely harmless, and we can simply allow
APM_EMULATION to be enabled here, even if PM is not.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Gautham R Shenoy [Wed, 27 Jan 2016 06:32:26 +0000 (12:02 +0530)]
cpufreq: Use list_is_last() to check last entry of the policy list
Currently next_policy() explicitly checks if a policy is the last
policy in the cpufreq_policy_list. Use the standard list_is_last
primitive instead.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Mon, 25 Jan 2016 17:03:46 +0000 (22:33 +0530)]
cpufreq: Fix NULL reference crash while accessing policy->governor_data
There is a race discovered by Juri, where we are able to:
- create and read a sysfs file before policy->governor_data is being set
to a non NULL value.
OR
- set policy->governor_data to NULL, and reading a file before being
destroyed.
This was found with the -RT patch enabled, but the fix should apply to
non-RT also.
Used multi_v7_defconfig+PREEMPT_RT_FULL=y and this caused a compilation
warning without this fix:
../drivers/cpuidle/coupled.c:122:21: warning: 'cpuidle_coupled_lock'
defined but not used [-Wunused-variable]
Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Moritz Fischer [Wed, 27 Jan 2016 07:29:27 +0000 (08:29 +0100)]
PM / Domains: Fix typo in comment
Acked-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Ulf Hansson [Wed, 27 Jan 2016 08:10:37 +0000 (09:10 +0100)]
PM / Domains: Fix potential deadlock while adding/removing subdomains
We must preserve the same order of how we acquire and release the lock for
genpd, as otherwise we may encounter deadlocks.
The power on phase of a genpd starts by acquiring its lock. Then it walks
the hierarchy of its parent domains to be able to power on these first, as
per design of genpd.
From a locking perspective this means the locks of the parents becomes
acquired after the lock of the subdomain.
Let's fix pm_genpd_add|remove_subdomain() to maintain the same order of
acquiring/releasing the genpd lock as being applied in the power on/off
sequence.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Wed, 27 Jan 2016 19:56:03 +0000 (11:56 -0800)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio tests and fixes from Michael Tsirkin:
"This fixes existing tests broken by barrier rework, and adds some new
tests.
Plus, there's a fix for an old bug in virtio-pci"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
tools/virtio: add ringtest utilities
sh: fix smp_store_mb for !SMP
tools/virtio: use virt_xxx barriers
virtio_pci: fix use after free on release
Brian Norris <computersforpeace@gmail.com> is reporting:
Ralf,
Please revert this and send it to Linus (or else, I can send it myself).
This is causing build failures, because I didn't take the rest of
Simon's series yet.
drivers/mtd/bcm63xxpart.c: In function 'bcm63xx_parse_cfe_partitions':
drivers/mtd/bcm63xxpart.c:93:2: error: implicit declaration of function
'bcm63xx_nvram_get_psi_size' [-Werror=implicit-function-declaration]
Linus Torvalds [Wed, 27 Jan 2016 19:08:30 +0000 (11:08 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The main thing here is to get us booting under qemu again after it
turned out that not all of the PMU registers are emulated there,
causing us to die early in boot.
- Ensure we don't access PMU registers of the PMU is not implemented
(fixes booting under QEMU)
- Fix BUG_ON triggered during module loading with DEBUG_SET_MODULE_RONX
- Ensure the kasan zero page is read-only
- Hide __efistub_ symbol aliases from kallsyms, since they otherwise
confuse the backtrace code
- Ensure !PTE_WRITE kernel ptes are marked as read-only
- defconfig updates based on requests and patches on the list
- Other minor fixes (typos, build system)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: avoid calling apply_to_page_range on empty range
arm64: defconfig: updates for 4.5
arm64: errata: Add -mpc-relative-literal-loads to build flags
Eliminate the .eh_frame sections from the aarch64 vmlinux and kernel modules
arm64: Fix an enum typo in mm/dump.c
arm64: Honour !PTE_WRITE in set_pte_at() for kernel mappings
arm64: kernel: fix architected PMU registers unconditional access
arm64: kasan: ensure that the KASAN zero page is mapped read-only
arm64: hide __efistub_ aliases from kallsyms
The email address <ao2@amarulasolutions.com> is not active anymore, use
Antonio's personal email address <ao2@ao2.it> in case someone wants to
get in touch for the code wrote for Amarula Solutions.
Signed-off-by: Antonio Ospite <ao2@ao2.it> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alex Williamson [Wed, 27 Jan 2016 18:22:25 +0000 (11:22 -0700)]
vfio/noiommu: Don't use iommu_present() to track fake groups
Using iommu_present() to determine whether an IOMMU group is real or
fake has some problems. First, apparently Power systems don't
register an IOMMU on the device bus, so the groups and containers get
marked as noiommu and then won't bind to their actual IOMMU driver.
Second, I expect we'll run into the same issue as we try to support
vGPUs through vfio, since they're likely to emulate this behavior of
creating an IOMMU group on a virtual device and then providing a vfio
IOMMU backend tailored to the sort of isolation they provide, which
won't necessarily be fully compatible with the IOMMU API.
The solution here is to use the existing iommudata interface to IOMMU
groups, which allows us to easily identify the fake groups we've
created for noiommu purposes. The iommudata we set is purely
arbitrary since we're only comparing the address, so we use the
address of the noiommu switch itself.
Slava Grigorev [Tue, 26 Jan 2016 22:35:57 +0000 (17:35 -0500)]
drm/radeon: fix DP audio support for APU with DCE4.1 display engine
Properly setup the DFS divider for DP audio for DCE4.1.
Signed-off-by: Slava Grigorev <slava.grigorev@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
projects / linux-beck.git / log