UFS device may have standard LUs and LUN id could be from 0x00 to 0x7F.
UFS device specification use "Peripheral Device Addressing Format"
(SCSI SAM-5) for standard LUs.
UFS device may also have the Well Known LUs (also referred as W-LU) which
again could be from 0x00 to 0x7F. For W-LUs, UFS device specification only
allows the "Extended Addressing Format" (SCSI SAM-5) which means the W-LUNs
would start from 0xC100 onwards.
This means max. LUN number reported from UFS device could be 0xC17F hence
this patch advertise the "max_lun" as 0xC17F which will allow SCSI mid
layer to detect the W-LUs as well.
But once the W-LUs are detected, UFSHCD driver may get the commands with
SCSI LUN id upto 0xC17F but UPIU LUN id field is only 8-bit wide so it
requires the mapping of SCSI LUN id to UPIU LUN id. This patch also add
support for this mapping.
UFS device specification requires the UFS devices to support 4 well known
logical units:
"REPORT_LUNS" (address: 01h)
"UFS Device" (address: 50h)
"RPMB" (address: 44h)
"BOOT" (address: 30h)
UFS device's power management needs to be controlled by "POWER CONDITION"
field of SSU (START STOP UNIT) command. But this "power condition" field
will take effect only when its sent to "UFS device" well known logical unit
hence we require the scsi_device instance to represent this logical unit in
order for the UFS host driver to send the SSU command for power management.
We also require the scsi_device instance for "RPMB" (Replay Protected
Memory Block) LU so user space process can control this LU. User space may
also want to have access to BOOT LU.
This patch adds the scsi device instances for each of all well known LUs
(except "REPORT LUNS" LU).
ufs: Active Power Mode - configuring bActiveICCLevel
The maximum power consumption in active is determined by bActiveICCLevel.
The configuration is done by reading max current supported by the
regulators connected to VCC, VCCQ and VCCQ2 rails on the boards, and
reading the current consumption levels from the device for each rails
(vcc/vccq/vccq2) using power descriptor.
We configure the bActiveICCLevel attribute, with the max value that
correspond to the minimum-of(VCC-current-level,VCCQ-current-level,
VCCQ2-current-level).
In order to minimize resume latency, pre-fetch icc levels and reference
clock during initialization and avoid reading them each link startup
during resume.
In ->hce_enable_notify() callback the vendor specific initialization
may carry out additional DME configuration using UIC commands and
hence the UIC command completion interrupt enable bit should be set
before the post reset notification.
Add retries if the link-startup fails. This is required since due to
hardware timing issues, the Uni-Pro link-startup might fail. The UFS
HCI recovery procedure contradicts the Uni-Pro sequence. The UFS HCI
specifies to resend DME_LINKSTARTUP command after IS.ULLS (link-lost
interrupt) is received. The Uni-Pro specifies that if link-startup
fails the link is in "down" state. The link-lost is indicated to the
DME user only when the link is up. Hence, the UFS HCI recovery procedure
of waiting for IS.ULLS and retrying link-startup may not work properly.
At the end, if detection fails, power off (disable clocks, regulators,
phy) if the UFS device detection fails. This saves power while UFS device
is not embedded into the system.
Currently reading query descriptor is more tightened to each
descriptor type. This patch generalize the approach and allows
reading any parameter from any query descriptor.
Add generic clock initialization support for UFSHCD platform
driver. The clock info is read from device tree using standard
clock bindings. A generic max-clock-frequency-hz property is
defined to save information on maximum operating clock frequency
the h/w supports.
UFS devices are powered by at most three external power supplies -
- VCC - The flash memory core power supply, 2.7V to 3.6V or 1.70V to 1.95V
- VCCQ - The controller and I/O power supply, 1.1V to 1.3V
- VCCQ2 - Secondary controller and/or I/O power supply, 1.65V to 1.95V
For some devices VCCQ or VCCQ2 are optional as they can be
generated using internal LDO inside the UFS device.
Add DT bindings for voltage regulators that can be controlled
from host driver.
Some vendor specific controller versions might need to configure
vendor specific - registers, clocks, voltage regulators etc. to
initialize the host controller UTP layer and Uni-Pro stack.
Provide some common initialization operations that can be used
to configure vendor specifics. The methods can be extended in
future, for example, for power mode transitions.
The operations are vendor/board specific and hence determined with
the help of compatible property in device tree.
scsi: don't add scsi_device if its already visible
If LLD has added scsi device (by calling scsi_add_device) before scheduling
async scsi_scan_host then scsi_finish_async_scan() will end up calling
scsi_sysfs_add_sdev for scsi device which was already added by LLD.
This patch fixes this issue by skipping the call to scsi_sysfs_add_sdev()
if it's already visible to rest of the kernel.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Dolev Raviv <draviv@codeaurora.org> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Douglas Gilbert [Sun, 31 Aug 2014 23:09:59 +0000 (19:09 -0400)]
scsi_debug: deadlock between completions and surprise module removal
A deadlock has been reported when the completion
of SCSI commands (simulated by a timer) was surprised
by a module removal. This patch removes one half of
the offending locks around timer deletions. This fix
is applied both to stop_all_queued() which is were
the deadlock was discovered and stop_queued_cmnd()
which has very similar logic.
This patch should be applied both to the lk 3.17 tree
and Christoph's drivers-for-3.18 tree.
Tested-and-reported-by: Milan Broz <gmazyland@gmail.com> Signed-off-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Mike Christie [Mon, 29 Sep 2014 18:55:41 +0000 (13:55 -0500)]
be2iscsi: check ip buffer before copying
Dan Carpenter found a issue where be2iscsi would copy the ip
from userspace to the driver buffer before checking the len
of the data being copied:
http://marc.info/?l=linux-scsi&m=140982651504251&w=2
This patch just has us only copy what we the driver buffer
can support.
Cc: <stable@vger.kernel.org> Tested-by: John Soni Jose <sony.john-n@emulex.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: Christoph Hellwig <hch@lst.de>
John Soni Jose [Fri, 26 Sep 2014 19:14:16 +0000 (15:14 -0400)]
be2iscsi : Bump the driver version
Bump the driver version
Signed-off-by: John Soni Jose <sony.john-n@emulex.com> Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
John Soni Jose [Fri, 26 Sep 2014 19:13:55 +0000 (15:13 -0400)]
be2iscsi : Fix kernel panic during reboot/shutdown
In the reboot/shutdown path, workqueue was destroyed after the
adapter resource were freed. The task associated with workqueue
was getting executed after resources were freed. This lead to
kernel panic.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com> Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
libfc: Replace rcu_assign_pointer() with RCU_INIT_POINTER()
The uses of "rcu_assign_pointer()" are NULLing out the pointers.
According to RCU_INIT_POINTER()'s block comment:
"1. This use of RCU_INIT_POINTER() is NULLing out the pointer"
it is better to use it instead of rcu_assign_pointer() because it has a
smaller overhead.
The following Coccinelle semantic patch was used:
@@
@@
qla2xxx: Add support for QFull throttling and Term Exchange retry
Through the qla target code, the qlt_send_term_exchange() routine
is used in various different places to cleanup an exchange. For the
case of IOCB request queue is full, the exchange is left unhandled/
dangling. Existing code does not have re-try logic to cleanup the
exchange. This patch add retry logic to cleanup the exchange before
letting new commands through.
For the case of FW running out of exchanges, driver need to reply
SAM_STAT_BUSY to the initiators. This patch add a pending queue
for the busy reply in case IOCB queue is unable to handle the cmd.
ABTS path takes path similar to regular task management, but
reset_count was not initialized when allocating mcmd causing
the response to get dropped in qlt_xmit_tm_rsp. Fix this by
initializing reset_count correctly.
A chip reset can occur after driver submits command to the stack. Abort
command processing if a chip reset has occurred or in progress when you
get a follow up for a command.
qla2xxx: Enable SLER conditionally in target mode.
Sequence level error recovery (aka FC Tape) is not really required
for disk devices. On heavily loaded system, with slow turn around,
a bunch of status enquiries using REC puts additional burden to the
target, so just turn off SLER by default.
When allocating memory for new session original patch does
not assign vha to op->vha resulting into NULL pointer
access during qlt_create_sess_from_atio().
Chad Dupuis [Thu, 25 Sep 2014 09:17:03 +0000 (05:17 -0400)]
qla2xxx: Fail adapter initialization on load ram failure.
If we fail to load one of the segments of firmware fail the operation
instead of trying to continue which will lead to a system crash since
the pointers to the next segment will not be updated correctly.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
qla2xxx: Disable laser for ISP2031 while unloading driver.
Nameserver data on FC switch is not refreshed when
qla2xxx driver is unloaded. Disabling laser for
ISP2031 will force FC switch to rescan ports and
clear fdmi entries from Nameserver.
When creating request/response queues from qla25xx_setup_mode(),
the shadow index register pointers were not being initialized
to point at the registers.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com> Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
mptfusion: enable no_write_same for vmware scsi disks
When using a virtual SCSI disk in a VMWare VM if blkdev_issue_zeroout is used
data can be improperly zeroed out using the mptfusion driver. This patch
disables write_same for this driver and the vmware subsystem_vendor which
ensures that manual zeroing out is used instead.
Cc: stable@vger.kernel.org BugLink: http://bugs.launchpad.net/bugs/1371591 Reported-by: Bruce Lucas <bruce.lucas@mongodb.com> Tested-by: Chris J Arges <chris.j.arges@canonical.com> Signed-off-by: Chris J Arges <chris.j.arges@canonical.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Tomas Henzl [Fri, 12 Sep 2014 12:44:15 +0000 (14:44 +0200)]
hpsa: add missing pci_set_master in kdump path
Add a call to pci_set_master(...) missing in the previous
patch "hpsa: refine the pci enable/disable handling".
Found thanks to Rob Elliot.
Signed-off-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Robert Elliott <elliott@hp.com> Tested-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
ipr: don't log error messages when applications issues illegal requests
Failing Device information are logged when IOA firmware detected these
illegal request such as IOA firmware doesn't support inquiry with page
code 2. The patch fixes the issue.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
storvsc: get rid of overly verbose warning messages
Get rid of the warning messages since they will clutter up various system logs
and are of questionable value to the end user. For debugging purposes, this
information can be gotten by setting the scsi log level appropriately.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Olaf Hering <olaf@aepfle.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
mpt2sas: fix undefined reference to `__udivdi3' compilation errors
This patch will fix the below compilation errors on i386 ARCH
drivers/built-in.o: In function `_scsih_qcmd':
mpt2sas_scsih.c:(.text+0x1e7b56): undefined reference to `__udivdi3'
mpt2sas_scsih.c:(.text+0x1e7b8a): undefined reference to `__umoddi3'
Used sector_div() API to fix above compilation errors.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Ching Huang [Tue, 19 Aug 2014 07:07:35 +0000 (15:07 +0800)]
arcmsr: clear outbound doorbell buffer completely
Clear outbound doorbell buffer completely for adapter type C. This is to
prevent getting bad data input from IOP before ioctl command processing
starts.
Signed-off-by: Ching Huang <ching2048@areca.com.tw> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
Added comment for to-do work.
Problem statement:
MFI link list in megaraid_sas driver is used from mfi-mpt pass-through commands.
This list can be corrupted due to many possible race conditions in driver and
eventually we may see kernel panic.
One example -
MFI frame is freed from calling process as driver send command via polling method and interrupt
for that command comes after driver free mfi frame (actually even after some other context reuse
the mfi frame). When driver receive MPT frame in ISR, driver will be using the index of MFI and
access that MFI frame and finally in-used MFI frame’s list will be corrupted.
High level description of new solution -
Free MFI and MPT command from same context.
Free both the command either from process (from where mfi-mpt pass-through was called) or from
ISR context. Do not split freeing of MFI and MPT, because it creates the race condition which
will do MFI/MPT list corruption.
Renamed the cmd_pool_lock which is used in instance as well as fusion with below name.
mfi_pool_lock and mpt_pool_lock to add more code readability.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com> Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
megaraid_sas : Add module parameter to disable IRQ-CPU affinity hint
Resending the patch. Addressed the review comments from Tomas Henzl.
For certain deployment, we may need to disable irq cpu affinity hint.
This module parameter provides option for use to disable irq cpu affinity hint
and allow irqbalancer to handle the rest.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com> Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
projects / linux-beck.git / log