drm/i915: Don't update staged config during force restore modesets
The force restore path relies on the staged config to preserve the
configuration used before a suspend/resume cycle. The update done to it
in intel_modeset_fixup_state() would cause that information to be lost
after the first modeset, making it impossible to restore the modes for
pipes B and C.
References: https://bugs.freedesktop.org/show_bug.cgi?id=90468 Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
drm/i915: Don't check modeset state in the hw state force restore path
Since the force restore logic will restore the CRTCs state one at a
time, it is possible that the state will be inconsistent until the whole
operation finishes. A call to intel_modeset_check_state() is done once
it's over, so don't check the state multiple times in between. This
regression was introduced in:
drm/i915: factor out compute_config from __intel_set_mode v3
v2: Rename check parameter to force_restore. (Matt)
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94431 Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Francisco Jerez [Fri, 29 May 2015 13:44:15 +0000 (16:44 +0300)]
drm/i915: Add SCRATCH1 and ROW_CHICKEN3 to the register whitelist.
Only bit 27 of SCRATCH1 and bit 6 of ROW_CHICKEN3 are allowed to be
set because of security-sensitive bits we don't want userspace to mess
with. On HSW hardware the whitelisted bits control whether atomic
read-modify-write operations are performed on L3 or on GTI, and when
set to L3 (which can be 10x-30x better performing than on GTI,
depending on the application) require great care to avoid a system
hang, so we currently program them to be handled on GTI by default.
Beignet can immediately start taking advantage of this change to
enable L3 atomics. Mesa should eventually switch to L3 atomics too,
but a number of non-trivial changes are still required so it will
continue using GTI atomics for now.
Signed-off-by: Francisco Jerez <currojerez@riseup.net> Reviewed-by: Zhigang Gong <zhigang.gong@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Francisco Jerez [Fri, 29 May 2015 13:44:14 +0000 (16:44 +0300)]
drm/i915: Extend the parser to check register writes against a mask/value pair.
In some cases it might be unnecessary or dangerous to give userspace
the right to write arbitrary values to some register, even though it
might be desirable to give it control of some of its bits. This patch
extends the register whitelist entries to contain a mask/value pair in
addition to the register offset. For registers with non-zero mask,
any LRM writes and LRI writes where the bits of the immediate given by
the mask don't match the specified value will be rejected.
This will be used in my next patch to grant userspace partial write
access to some sensitive registers.
Signed-off-by: Francisco Jerez <currojerez@riseup.net> Reviewed-by: Zhigang Gong <zhigang.gong@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Francisco Jerez [Fri, 29 May 2015 13:44:13 +0000 (16:44 +0300)]
drm/i915: Fix command parser to validate multiple register access with the same command.
Until now the software command checker assumed that commands could
read or write at most a single register per packet. This is not
necessarily the case, MI_LOAD_REGISTER_IMM expects a variable-length
list of offset/value pairs and writes them in sequence. The previous
code would only check whether the first entry was valid, effectively
allowing userspace to write unrestricted registers of the MMIO space
by sending a multi-register write with a legal first register, with
potential security implications on Gen6 and 7 hardware.
Fix it by extending the drm_i915_cmd_descriptor table to represent
multi-register access and making validate_cmd() iterate for all
register offsets present in the command packet.
Signed-off-by: Francisco Jerez <currojerez@riseup.net> Reviewed-by: Zhigang Gong <zhigang.gong@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ville Syrjälä [Thu, 28 May 2015 15:32:36 +0000 (18:32 +0300)]
drm/i915: Don't skip request retirement if the active list is empty
Apparently we can have requests even if though the active list is empty,
so do the request retirement regardless of whether there's anything
on the active list.
The way it happened here is that during suspend intel_ring_idle()
notices the olr hanging around and then proceeds to get rid of it by
adding a request. However since there was nothing on the active lists
i915_gem_retire_requests() didn't clean those up, and so the idle work
never runs, and we leave the GPU "busy" during suspend resulting in a
WARN later.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
drm/i915: Use complete address space in true PPGTT
v2: Prettify code and explain why this is needed. (Chris)
v3: Don't hide the compilation warning in 32-bit. (Chris)
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Michel Thierry <michel.thierry@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rodrigo Vivi [Thu, 28 May 2015 17:26:58 +0000 (10:26 -0700)]
drm/i915: Another fbdev hack to avoid PSR on fbcon.
With unified modeset and flip paths introduced recently when switching
to fbcon PSR was being disabled on fb_set_par path but re-enabled on
fb_pan_display one, causing missed screen updates and un unusable
console.
Regression introduced with:
commit bb54662350662815b4bfc2ff4464330a2dbd7041
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Apr 21 17:13:13 2015 +0300
drm/i915: Unify modeset and flip paths of intel_crtc_set_config()
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rodrigo Vivi [Thu, 28 May 2015 17:21:16 +0000 (10:21 -0700)]
drm/i915: Return the frontbuffer flip to enable intel_crtc_enable_planes.
Without this frontbuffer flip when enabling planes PSR got compromised
and wasn't being enabled waiting forever on the flush that never
arrived.
Another solution would to create a enable_cursor function and split this
frontbuffer flip among the different plane enable and disable functions.
But if necessary this can be done in a follow up work. For now let's
just fix the regression.
Paulo Zanoni [Mon, 25 May 2015 21:52:29 +0000 (18:52 -0300)]
drm/i915: disable IPS while getting the sink CRCs
This commit is the "sink CRC" version of:
commit 8c740dcea254a1472df2c0ac5ac585412a2507ec
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Oct 17 18:42:03 2014 -0300
drm/i915: disable IPS while getting the pipe CRCs.
For some unknown reason, when IPS gets enabled, the sink CRC changes.
Since hsw_enable_ips() doesn't really guarantee to enable IPS (it
depends on package C-states), we can't really predict if IPS is
enabled or disabled while running our CRC tests, so let's just
completely disable IPS while sink CRCs are being used.
If we find a way to make IPS not change the pipe CRC result, we may
want to fix IPS and then revert this patch (and 8c740dcea too). While
this doesn't happen, let's merge this patch, so the IGT tests relying
on sink CRCs can work properly.
This was discovered while developing a new IGT test, which will
probably be called kms_frontbuffer_tracking.
Testcase: igt/kms_frontbuffer_tracking (not on upstream IGT yet) Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Select starting pipe bpp irrespective or the primary plane
the kernel will try to use it even for the common rgb888 framebuffers.
Ville has patches to fix it all up properly, but unfortunately they're
stuck in review limbo. And since the 4.2 feature cutoff has passed we
need to somehow handle this regression.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Paulo Zanoni <przanoni@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Ville Syrjälä [Tue, 26 May 2015 17:42:31 +0000 (20:42 +0300)]
drm/i915: Adjust sideband locking a bit for CHV/VLV
chv_enable_pll() doesn't need to hold sb_lock for the entire duration of
the function. Drop the lock as soon as possible.
valleyview_set_cdclk() does a potential lock+unlock+lock+unlock cycle
with sb_lock. Grab the lock a few lines earlier so we can make do
with a single lock+unlock cycle always.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 26 May 2015 17:42:30 +0000 (20:42 +0300)]
drm/i915: s/dpio_lock/sb_lock/
Rename dpio_lock to sb_lock to inform the reader that its primary
purpose is to protect the sideband mailbox rather than some DPIO
state.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 26 May 2015 17:27:23 +0000 (20:27 +0300)]
drm/i915: Kill intel_flush_primary_plane()
The primary plane frobbing was removed from the sprite code in
commit ecce87ea3ab55ad0dc64460e6422c357d158a55e
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Tue Apr 21 17:12:50 2015 +0300
drm/i915: Remove implicitly disabling primary plane for now
but the intel_flush_primary_plane() calls were left behind. Replace them
with straight forward POSTING_READ() of the sprite surface address
register.
The other user of intel_flush_primary_plane() is g4x_disable_trickle_feed()
where we can just inline the steps directly.
This allows intel_flush_primary_plane() to be killed off.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 26 May 2015 17:22:39 +0000 (20:22 +0300)]
drm/i915: Throw out WIP CHV power well definitions
Expecting CHV power wells to be just an extended versions of the VLV
power wells, a bunch of commented out power wells were added in
anticipation when Punit folks would implement it all. Turns out they
never did, and instead CHV has fewer power wells than VLV. Rip out all
the #if 0'ed junk that's not needed.
v2: Rename the "pipe-a" well to "display" to match VLV
Clarify the pipe A power well relationship to pipes B and C (Deepak)
Reviewed-by: Deepak S <deepak.s@linux.intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 26 May 2015 17:22:38 +0000 (20:22 +0300)]
drm/i915: Use the default 600ns LDO programming sequence delay
Not sure which LDO programming sequence delay should be used for the CHV
PHY, but the spec says that 600ns is "Used by default for initial
bringup", and the BIOS seems to use that, so let's do the same.
Reviewed-by: Deepak S <deepak.s@linux.intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Michel Thierry [Mon, 27 Apr 2015 11:31:44 +0000 (12:31 +0100)]
drm/i915: Remove unnecessary null check in execlists_context_unqueue
commit 53292cdb066950611e5bc2e0eb109c7edb42af78 ("drm/i915: Workaround
to avoid lite restore with HEAD==TAIL") added a check for req0 != null
which is unnecessary.
The only way req0 could be null is if the list was empty, and this is
already addressed at the beginning of execlists_context_unqueue().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Michel Thierry <michel.thierry@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Deminish contribution of wait-boosting from clients
we removed an atomic timer based check for allowing waitboosting and
moved it below the mutex taken during RPS. However, that mutex can be
held for long periods of time on Vallyview/Cherryview as communication
with the PCU is slow. As clients may frequently wait for results (e.g.
such as tranform feedback) we introduced contention between the client
and the RPS worker. We can take advantage of the RPS worker, by
switching the wait boost decision to use spin locks and defer the
actual reclocking to the worker.
Fixes a regression of up to 45% on Baytrail and Baswell!
v2 (Daniel):
- Use max_freq_softlimit instead of the not-yet-merged boost
frequency.
- Don't inject a fake irq into the boost work, instead treat
client_boost as just another legit waker.
v3: Drop the now unused mask (Chris).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90112 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v1) Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's causing too much trouble when compile-testing for non-i915 folks.
Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
it is better to be explicit when sharing hardcoded values such as
throttle/boost timeouts. Make it so!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Thu, 21 May 2015 20:01:45 +0000 (21:01 +0100)]
drm/i915: Use the correct destructor for freeing requests on error
After allocating from the slab cache, we then need to free the request
back into the slab cache upon error (and not call kfree as that leads
to eventual memory corruption).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is a mplayer video failure reported with xv.
This is because there is a request to do both plane scaling
and colorkey. Because skl hw doesn't support plane scaling
and colorkey at the same time, request is failed which is expected
behavior.
To make xv operate, this patch allows colorkey continue to work
without using scaler. Then behavior would be similar to platforms
without plane scaler support.
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90449
[danvet: change can_scale to bool as requested by Ville.] Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 19 May 2015 17:32:57 +0000 (20:32 +0300)]
drm/i915: Enable GTT caching on gen8
GTT caching was disabled by default on gen8 due to not working with
big pages. Some information suggests that it got fixed, but still
GTT caching has been left disabled by default. Or could be it just
meant that the default was changed to off, and hence the problem
got solved.
Enable GTT caching in the hopes of some performance increase.
Whether or not the big pages issue has been fixed is irrelevant
at this stage since we don't use big pages.
This gives me a 1-2% improvement in xonotic on my BSW. Haven't tried
BDW, but supposedly it has larger TLBs so might not benefit as much.
On HSW GTT caching is enabled by default.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 19 May 2015 17:32:56 +0000 (20:32 +0300)]
drm/i915: Move WaProgramL3SqcReg1Default:bdw to init_clock_gating()
GEN8_L3SQCREG1 isn't saved in the context (verified by going through
a context dump), and so we shouldn't be using the ring w/a code to
initialize it. Also Bspec explicitly talks about MMIO and writing it
with the CPU.
Additionally there's another w/a WaTempDisableDOPClkGating:bdw which
tells us to disable DOP clock gating around the GEN8_L3SQCREG1 write
to make sure everyone notices the change. So let's do that as well.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 19 May 2015 17:32:55 +0000 (20:32 +0300)]
drm/i915: Use ilk_init_lp_watermarks() on BDW
We're not using ilk_init_lp_watermarks() on BDW for some reason.
Probably due to the BDW patches and the relevant WM patches landing
roughlly at the same time. Fix it up.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 5 May 2015 14:17:36 +0000 (17:17 +0300)]
drm/i915: Disable SDVO port after the pipe on PCH platforms
While at it also remove the redundant/unneeded w/a like done for hdmi
already.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Mention that this also removes the unneeded w/a, as suggested
by Jesse.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 5 May 2015 14:17:35 +0000 (17:17 +0300)]
drm/i915: Disable HDMI port after the pipe on PCH platforms
BSpec says we should disable all ports after the pipe on PCH
platforms. Do so. Fixes a pipe off timeout on ILK now caused by
the transcoder B workaround.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 5 May 2015 14:17:34 +0000 (17:17 +0300)]
drm/i915: Fix the IBX transcoder B workarounds
Currently the IBX transcoder B workarounds are not working correctly.
Well, the HDMI one seems to be working somewhat, but the DP one is
definitely busted.
After a bit of experimentation it looks like the best way to make this
work is first disable the port on transcoder B, and then re-enable it
transcoder A, and immediately disable it again.
We can also clean up the code by noting that we can't be called without
a valid crtc. And also note that port A on ILK does not need the
workaround, so let's check for that one too.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 5 May 2015 14:17:33 +0000 (17:17 +0300)]
drm/i915: Write the SDVO reg twice on IBX
On IBX the SDVO/HDMI register write may be masked when enabling the
port, so it may need to written twice. The HDMI code does this, but
the SDVO code does not. Add the workaround to the SDVO code as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 5 May 2015 14:17:31 +0000 (17:17 +0300)]
drm/i915: Fix DP enhanced framing for CPT
Currently we're always enabling enhanced framing on CPT even if the sink
doesn't support it. Fix this up by actaully looking at what the sink
tells us.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 5 May 2015 14:17:29 +0000 (17:17 +0300)]
drm/i915: Clarfify the DP code platform checks
intel_dp.c is a mess with all the checks for different
platform/PCH variants and ports. Try to clean it up by recognizing
the following facts:
- IVB port A, and CPT port B/C/D are always the special cases
- VLV/CHV don't have port A
- Using the same kind of logic everywhere makes things much easier to
parse
So let's move the IVB port A and PCH port B/C/D checks to be done first,
and let the other cases fall through, and always check for these things
using the same logic.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 5 May 2015 14:17:28 +0000 (17:17 +0300)]
drm/i915: Remove the double register write from intel_disable_hdmi()
IBX can have problems with the first write to the port register getting
masked when enabling the port. We are trying to apply the workaround
also when disabling the port where it's not needed, and we also try
to apply it for CPT/PPT as well which don't need it. Just kill it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Resolve conflict with the remove CHV if block.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 5 May 2015 14:17:27 +0000 (17:17 +0300)]
drm/i915: Remove a bogus 12bpc "toggle" from intel_disable_hdmi()
The IBX 12bpc port enable toggle is only relevant when enabling
the port, not when disabling it. Also this code doesn't actually
toggle anything, and essentially just writes the port register
one extra time. Furthermore CPT/PPT don't need such workarounds
and yet we include them. Just kill it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Thu, 21 May 2015 15:37:48 +0000 (16:37 +0100)]
drm/i915/skl: Deinit/init the display at suspend/resume
We need to re-init the display hardware when going out of suspend. This
includes:
- Hooking the PCH to the reset logic
- Restoring CDCDLK
- Enabling the DDB power
Among those, only the CDCDLK one is a bit tricky. There's some
complexity in that:
- DPLL0 (which is the source for CDCLK) has two VCOs, each with a set
of supported frequencies. As eDP also uses DPLL0 for its link rate,
once DPLL0 is on, we restrict the possible eDP link rates the chosen
VCO.
- CDCLK also limits the bandwidth available to push pixels.
So, as a first step, this commit restore what the BIOS set, until I can
do more testing.
In case that's of interest for the reviewer, I've unit tested the
function that derives the decimal frequency field:
for (i = 0; i < ARRAY_SIZE(freqs); i++)
test_freq(&freqs[i]);
return 0;
}
v2:
- Rebase on top of -nightly
- Use (freq - 1000) / 500 for the decimal frequency (Ville)
- Fix setting the enable bit of HSW_NDE_RSTWRN_OPT (Ville)
- Rename skl_display_{resume,suspend} to skl_{init,uninit}_cdclk to
be consistent with the BXT code (Ville)
- Store boot CDCLK in ddi_pll_init (Ville)
- Merge dev_priv's skl_boot_cdclk into cdclk_freq
- Use LCPLL_PLL_LOCK instead of (1 << 30) (Ville)
- Replace various '0' by SKL_DPLL0 to be a bit more explicit that
we're programming DPLL0
- Busy poll the PCU before doing the frequency change. It takes about
3/4 cycles, each separated by 10us, to get the ACK from the CPU
(Ville)
v3:
- Restore dev_priv->skl_boot_cdclk, leaving unification with
dev_priv->cdclk_freq for a later patch (Daniel, Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 27 Apr 2015 12:41:24 +0000 (13:41 +0100)]
drm/i915: Free RPS boosts for all laggards
If the client stalls on a congested request, chosen to be 20ms old to
match throttling, allow the client a free RPS boost.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
[danvet: s/0/NULL/ reported by 0-day build] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 27 Apr 2015 12:41:23 +0000 (13:41 +0100)]
drm/i915: Don't downclock whilst we have clients waiting for GPU results
If we have clients stalled waiting for requests, ignore the GPU if it
signals that it should downclock due to low load. This helps prevent
the automatic timeout from causing extremely long running batches from
taking even longer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 27 Apr 2015 12:41:22 +0000 (13:41 +0100)]
drm/i915: Convert RPS tracking to a intel_rps_client struct
Now that we have internal clients, rather than faking a whole
drm_i915_file_private just for tracking RPS boosts, create a new struct
intel_rps_client and pass it along when waiting.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 27 Apr 2015 12:41:21 +0000 (13:41 +0100)]
drm/i915: Limit mmio flip RPS boosts
Since we will often pageflip to an active surface, we will often have to
wait for the surface to be written before issuing the flip. Also we are
likely to wait on that surface in plenty of time before the vblank.
Since we have a mechanism for boosting when a flip misses the expected
vblank, curtain the number of times we RPS boost when simply waiting for
mmioflip.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 27 Apr 2015 12:41:20 +0000 (13:41 +0100)]
drm/i915: Limit ring synchronisation (sw sempahores) RPS boosts
Ring switches can occur many times per frame, and are often out of
control, causing frequent RPS boosting for no practical benefit. Treat
the sw semaphore synchronisation as a separate client and only allow it
to boost once per busy/idle cycle.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, we only track the last request globally across all engines.
This prevents us from issuing concurrent read requests on e.g. the RCS
and BCS engines (or more likely the render and media engines). Without
semaphores, we incur costly stalls as we synchronise between rings -
greatly impacting the current performance of Broadwell versus Haswell in
certain workloads (like video decode). With the introduction of
reference counted requests, it is much easier to track the last request
per ring, as well as the last global write request so that we can
optimise inter-engine read read requests (as well as better optimise
certain CPU waits).
v2: Fix inverted readonly condition for nonblocking waits.
v3: Handle non-continguous engine array after waits
v4: Rebase, tidy, rewrite ring list debugging
v5: Use obj->active as a bitfield, it looks cool
v6: Micro-optimise, mostly involving moving code around
v7: Fix retire-requests-upto for execlists (and multiple rq->ringbuf)
v8: Rebase
v9: Refactor i915_gem_object_sync() to allow the compiler to better
optimise it.
Benchmark: igt/gem_read_read_speed
hsw:gt3e (with semaphores):
Before: Time to read-read 1024k: 275.794µs
After: Time to read-read 1024k: 123.260µs
hsw:gt3e (w/o semaphores):
Before: Time to read-read 1024k: 230.433µs
After: Time to read-read 1024k: 124.593µs
bdw-u (w/o semaphores): Before After
Time to read-read 1x1: 26.274µs 10.350µs
Time to read-read 128x128: 40.097µs 21.366µs
Time to read-read 256x256: 77.087µs 42.608µs
Time to read-read 512x512: 281.999µs 181.155µs
Time to read-read 1024x1024: 1196.141µs 1118.223µs
Time to read-read 2048x2048: 5639.072µs 5225.837µs
Time to read-read 4096x4096: 22401.662µs 21137.067µs
Time to read-read 8192x8192: 89617.735µs 85637.681µs
Testcase: igt/gem_concurrent_blit (read-read and friends) Cc: Lionel Landwerlin <lionel.g.landwerlin@linux.intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> [v8]
[danvet: s/\<rq\>/req/g] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 21 May 2015 12:21:25 +0000 (14:21 +0200)]
drm/i915: s/\<rq\>/req/g
The merged seqno->request conversion from John called request
variables req, but some (not all) of Chris' recent patches changed
those to just rq. We've had a lenghty (and inconclusive) discussion on
irc which is the more meaningful name with maybe at most a slight bias
towards req.
Given that the "don't change names without good reason to avoid
conflicts" rule applies, so lets go back to a req everywhere for
consistency. I'll sed any patches for which this will cause conflicts
before applying.
Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: John Harrison <John.C.Harrison@Intel.com>
[danvet: s/origina/merged/ as pointed out by Chris - the first
mass-conversion patch was from Chris, the merged one from John.] Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
v2:
- set the override disable flag too on stepping F0 (mika)
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Spotted-by: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 20 May 2015 13:12:47 +0000 (14:12 +0100)]
drm/i915: Force clean compilation with -Werror
Our driver compiles clean (nowadays thanks to 0day) but for me, at least,
it would be beneficial if the compiler threw an error rather than a
warning when it found a piece of suspect code. (I use this to
compile-check patch series and want to break on the first compiler error
in order to fix the patch.)
v2: Kick off a new "Debugging" submenu for i915.ko
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Add "DRM i915" to the menu name as requested by Chris.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Sonika Jindal [Wed, 20 May 2015 08:10:48 +0000 (13:40 +0530)]
drm/i915/skl: Swapping 90 and 270 to be compliant with Xrandr
Since DRM_ROTATE is counter clockwise (which is compliant with Xrandr),
and HW rotation is clockwise, swapping 90/270 to work as expected from
userspace.
v2: Rebased
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Sonika Jindal <sonika.jindal@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 19 May 2015 11:29:16 +0000 (12:29 +0100)]
drm/i915: Tighten the exposure ARGB/ABGR 8888 formats
ARGB8888 is used for cursors on all platforms so we need to allow it
everywhere.
ABGR8888 is currently only honoured:
- on VLV/CHV in sprite planes
- on SKL+ for primary and sprite planes
so only allow it for those platforms.
Note that we only support ARGB8888/ABGR8888 on the primary plane for
SKL/BXT because we have in line of sight the pipe bottom color on those
platforms and because the primary plane programming on VLV/CHV doesn't
anything different for those formats today.
v2: Fix the logic to forbid the creation ABGR2101010 fbs (Ville)
v3: Still allow the creation of ARGB8888 fbs now that cursor planes use
real fb objects (found by PRTS).
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Vandana Kannan [Wed, 13 May 2015 06:48:52 +0000 (12:18 +0530)]
drm/i915/bxt: Port PLL programming BUN
BUN 1: prop_coeff, int_coeff, tdctargetcnt programming updated and tied to
VCO frequencies. Program i_lockthresh in PORT_PLL_9.
VCO calculated based on the formula:
Desired Output = Port bit rate in MHz (DisplayPort HBR2 is 5400 MHz)
Fast Clock = Desired Output / 2
VCO = Fast Clock * P1 * P2
Prop_coeff, int_coeff, and tdctargetcnt modified according to above
calculation.
BUN 2: Port PLLs require additional programming at certain frequencies -
DCO amplitude in PORT_PLL_10
Review comments from Siva which were addressed in the initial version of the
patch.
- Change PORT_PLL_LOCK_THRESHOLD to PORT_PLL_LOCK_THRESHOLD_MASK
- Calculate for HDMI
- Correct values for vco = 5.4
- return in case of invalid vco range
v2: Imre's review comments addressed
- change dcoampovr_en to dcoampovr_en_h
- change PORT_PLL_DCO_AMP_OVR_EN to PORT_PLL_DCO_AMP_OVR_EN_H
- Correct lane stagger value for 324MHz
- Make coef common for HDMI and DP
- remove superfluous comments
v3: Imre's comments addressed
- Remove Prop_coeff, int_coeff, tdctargetcnt, dcoampovr_en, gain_ctl,
dcoampovr_en_h from bxt_clk_div and make them local variables.
Chris Wilson [Fri, 15 May 2015 10:42:21 +0000 (11:42 +0100)]
drm/i915: Use uninterruptible mutex_lock for userptr bo creation
Mika encountered one pathological scenario under X where acquiring all
the mm locks (required to insert a mmu notifier) was very slow, so slow
that by the time we tried to lock the struct_mutex with the usual call
to i915_mutex_lock_interruptible(), X's signal timer had fired causing
us to restart the ioctl (and so looped indefinitely).
While I suspect this is the result of another bug (something leaking mm
perhaps?) we can forgo the error checking and interuptible nature of the
lock here so we only have to pay the expense once and get on with it.
This does expose the userptr creation routine to a driver livelock
though by not being interruptible.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Init ret to avoid issues reported by PRTS.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Preserve ddi_pll_sel when allocating new pipe_config
When the modeset code is reached with a CRTC that only needs a flip, the
code that assigns PLLs is skipped. But since there is still a state swap
for that CRTC, the current PLL assignment needs to be preserved. I
missed the ddi_pll_sel field in the following commit, which causes
warnings in DDI platforms.
commit 4978cc93d9ac240b435ce60431aef24239b4c270
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Apr 21 17:13:21 2015 +0300
drm/i915: Preserve shared DPLL information in new pipe_config
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90410 Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Don't overwrite (e)DP PLL selection on SKL
In the following commit, the place where the contents of dpll_hw_state
in crtc_state where zeroed was changed. Prior to that commit, it
happened when the new state was allocated, but now that happens just
before the call the .crtc_compute_clock() hook. The DP code for SKL,
however, sets up the (private) PLL in the encoder compute config
function that has already run by the time that memset() is reached,
causing the previous value to be lost.
This patch fixes the issue by moving the memset() down the call chain,
so that it is only called if the values in dpll_hw_state are going to be
updated.
commit 4978cc93d9ac240b435ce60431aef24239b4c270
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Apr 21 17:13:21 2015 +0300
drm/i915: Preserve shared DPLL information in new pipe_config
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90462 Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Reported-and-tested-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Wed, 13 May 2015 12:34:05 +0000 (15:34 +0300)]
drm/i915/bios: be more explicit about discarding iomem address space
Add one explicit discard of __iomem address space qualifier in
validate_vbt(), and respect it otherwise. This adds clarity in the code,
and reduces the sparse warnings from the module to just one.
Quoting Daniel, "The vbt really is plain old memory. Except that it's
reserved in the e820 table as something special and hence treated as io
range by the kernel. But it is memory, hence casting away the __iomem is
imo the right approach."
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Fri, 15 May 2015 14:07:02 +0000 (15:07 +0100)]
drm/i915/skl: Remove unnecessary local variables in skl_plane_ctl*()
Ville noticed in another patch we we didn't need them at all, so remove
them. It's worth saying that it makes no difference to code generated as
gcc is clever enough to optimize it out.
v2: Remove 'break' after 'return' in switches (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Wed, 13 May 2015 07:35:25 +0000 (10:35 +0300)]
drm/i915/dsi: add support for DSI PLL N1 divisor values
Currently DSI PLL N1 is hardcoded off. Make it possible to use it
later. This should have no functional changes for now.
v2: s/ffz(~(n))/ffs(n) - 1/ (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Animesh Manna [Wed, 13 May 2015 16:43:29 +0000 (22:13 +0530)]
drm/i915/skl: Documentation for CSR firmware
Added docbook info regarding context save and restore (CSR)
firmware support added from gen9 onwards to drive newly added
DMC (Display microcontroller) in display engine.
v1: Initial version as RFC.
v2: Used "DOC:" tag for csr description based on review comment from Daniel.
Signed-off-by: Animesh Manna <animesh.manna@intel.com> Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Fri, 15 May 2015 10:09:21 +0000 (13:09 +0300)]
drm/i915: Don't read dpcd for disconnected ports
Reading from disconnected ports will spit out timeout error
on the dmesg. Skip the attempted read if the port is not
connected and avoid confusing users/testcases about
expected timeouts.
This new dpcd debugfs entry was introduced by commit aa7471d228eb
("drm/i915: add i915 specific connector debugfs file for DPCD")
v2 by Jani: move the check at the top, out of the loop.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90060 Tested-by: yex.tian@intel.com Cc: Jani Nikula <jani.nikula@intel.com> Cc: Bob Paauwe <bob.j.paauwe@intel.com> Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dan Carpenter [Tue, 12 May 2015 18:07:37 +0000 (21:07 +0300)]
drm/edid: fix a debug message
There is an extra semi-colon on the if statement so the debug output
always says "Failed to write EDID checksum" even when it didn't fail.
Fixes: 559be30cb74d ('drm/i915: Implement the intel_dp_autotest_edid function for DP EDID complaince tests') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 12 May 2015 15:13:16 +0000 (16:13 +0100)]
drm/i915/skl: Replace BUG() by MISSING_CASE() in skl_plane_ctl_format()
Let's be consistent with the others skl_plane_ctl_*() functions and use
a MISSING_CASE(). Not only that, but it's a rude to BUG() the whole
machine here.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Tue, 12 May 2015 12:23:09 +0000 (15:23 +0300)]
drm/i915: clean up dsi pll calculation
Improve readability. No functional changes.
v2: use more rational types (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Tue, 12 May 2015 12:41:32 +0000 (15:41 +0300)]
drm/i915: constify validate_vbt in VBT parsing
Make input and output of validate_vbt const, and fix the fallout. We
shouldn't modify the VBT, so make the compiler help us here.
v2: use pointer arithmetics on void* to simplify (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Wed, 15 Apr 2015 12:18:28 +0000 (15:18 +0300)]
drm/i915: constify find_section in VBT parsing
Make input and output of find_section const, and fix the fallout. We
shouldn't modify the VBT, so make the compiler help us here.
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 11 May 2015 17:49:10 +0000 (20:49 +0300)]
drm/i915: Use HOTPLUG_INT_STATUS_G4X on VLV/CHV
Use HOTPLUG_INT_STATUS_G4X instead of HOTPLUG_INT_STATUS_I915 on VLV/CHV
so that we don't confuse the AUX status bits with SDVO status bits.
Avoid pointless log spam as below while handling AUX interrupts:
[drm:intel_hpd_irq_handler] hotplug event received, stat 0x00000040, dig 0x00000000
[drm:intel_hpd_irq_handler] hotplug event received, stat 0x00000040, dig 0x00000000
[drm:intel_hpd_irq_handler] hotplug event received, stat 0x00000040, dig 0x00000000
[drm:intel_hpd_irq_handler] hotplug event received, stat 0x00000040, dig 0x00000000
[drm:intel_hpd_irq_handler] hotplug event received, stat 0x00000040, dig 0x00000000
[drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x71450064
Note that there's no functional issue, it's just that the sdvo bits
overlap with the dp aux bits. Hence every time we receive an aux
interrupt we also think there's an sdvo hpd interrupt, but due to lack
of any sdvo encoders nothing ever happens because of that.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Add Ville's explanation why nothing functional really
changes.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 11 May 2015 17:49:09 +0000 (20:49 +0300)]
drm/i915: Remove excess inline keywords
Remove some inline keywords. One of the functions has clearly outgrown
it anyway, so let's just leave it to the compiler.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Tue, 12 May 2015 07:35:08 +0000 (10:35 +0300)]
drm/i915/gtt: Fix the boundary check for vm area
The check for start + length >= total_vm_size is
wrong since start + length can be exactly the size of
the vm.
Fix the check to allow allocation to boundary.
Fixes a regression in commit 4dd738e9cd79
("drm/i915: Fix 32b overflow check in gen8_ppgtt_alloc_page_directories")
Testcase: igt/gem_evict_everything/swapping-interruptible
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90399 Tested-by: Lu Hua <huax.lu@intel.com> Cc: Chris Wilson <chris@chris.wilson.co.uk> Cc: Dave Gordon <david.s.gordon@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Michel Thierry <michel.thierry@intel.com> Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chandra Konduru [Mon, 11 May 2015 21:35:47 +0000 (14:35 -0700)]
drm/i915: Make scaler_id check in check_crtc_state work for all gens
During check_crtc_state, scaler_id mispatch is being reported for HSW.
This is applicable for skl+ and not for HSW. It is introduced by
commit id:
commit a1b2278e4dfcd2dbea85e319ebf73a6b7b2f180b
Author: Chandra Konduru <chandra.konduru@intel.com>
Date: Tue Apr 7 15:28:45 2015 -0700
drm/i915: skylake panel fitting using shared scalers
This patch will make sure that we leave scaler_id as 0 for platforms
before skl and set for skl+ only. This way scaler_id check during
check_crtc_state will pass for both prior to skl and skl+ platforms.
v2:
-Leave scaler_id as 0 for gen < 9 (Daniel)
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
References: http://lists.freedesktop.org/archives/intel-gfx/2015-May/065741.html Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 27 Apr 2015 12:41:16 +0000 (13:41 +0100)]
drm/i915: Fix race on unreferencing the wrong mmio-flip-request
As we perform the mmio-flip without any locking and then try to acquire
the struct_mutex prior to dereferencing the request, it is possible for
userspace to queue a new pageflip before the worker can finish clearing
the old state - and then it will clear the new flip request. The result
is that the new flip could be completed before the GPU has finished
rendering.
The bugs stems from removing the seqno checking in
commit 536f5b5e86b225dab94c7ff8061ae482b6077387
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Thu Nov 6 11:03:40 2014 +0200
drm/i915: Make mmio flip wait for seqno in the work function
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 27 Apr 2015 12:41:15 +0000 (13:41 +0100)]
drm/i915: Ensure cache flushes prior to doing CS flips
Synchronising to an object active on the same ring is a no-op, for the
benefit of execbuffer scheduler. However, for CS flips this means that
we can forgo checking whether the last write request of the object is
actually queued and more importantly whether the cache flush for the
write was emitted.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 27 Apr 2015 12:41:14 +0000 (13:41 +0100)]
drm/i915: Remove domain flubbing from i915_gem_object_finish_gpu()
We no longer interpolate domains in the same manner, and even if we did,
we should trust setting either of the other write domains would trigger
an invalidation rather than force it. Remove the tweaking of the
read_domains since it serves no purpose and use
i915_gem_object_wait_rendering() directly.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add notes with information dug out of git history.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
projects / linux-beck.git / log