Ezequiel Garcia [Thu, 13 Mar 2014 20:24:30 +0000 (17:24 -0300)]
ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
The Armada 38x SoC family has a clock provider called "Core Divider",
derived from the fixed 2 GHz main PLL clock. This is similar to the
one on A370, A375 and AXP.
Ezequiel Garcia [Thu, 13 Mar 2014 20:24:29 +0000 (17:24 -0300)]
ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
Armada 38x SoCs have a 2 GHz fixed main PLL that is used to feed
other clocks. This commit adds a DT representation of this clock
through a fixed-clock compatible node.
Marvell Dove's pinctrl does require some PMU regs for muxing PMU
functions to MPP pins. Recently, a discussion started about consolidating
Power Management Unit (PMU) into a single DT node. As we don't want
anymore DT ABI in the way, drop the corresponding reg property from
pinctrl node now. The driver will derive the registers from existing
reg properties.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Gregory CLEMENT [Thu, 6 Mar 2014 15:17:55 +0000 (16:17 +0100)]
ARM: mvebu: add Device Tree for the Armada 385 RD board
The Armada 385 RD board is the reference design board from Marvell
for the Armada 385 SoC. This commit adds a Device Tree description for
this board, which enables the following features:
* Network interfaces
* I2C bus
* Serial port
* SPI bus, with a SPI flash
* PCIe interface
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
ARM: mvebu: use the correct phy connection mode on Armada 385 DB
On Armada 385 DB, while the "rgmii" PHY connection mode works fine
with the generic PHY driver, it fails to work when the Marvell PHY
driver is enabled in the kernel configuration, due to a finer handling
of the PHY configuration. This is due to the fact that the phy
connection mode should instead be "rgmii-id", i.e with the TX/RX delay
mechanisms enabled.
This fixes the network operation on Armada 385 DB with
CONFIG_MARVELL_PHY=y. Without this patch and this option enabled, one
would only get messages such as:
mvneta f1070000.ethernet eth1: bad rx status 0cc10000 (crc error), size=70
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Since the Armada XP Matrix board has 4 GB of RAM and not 2 GB, we
update the Device Tree to take into account the correct amount of
memory. As noted in the new comment, the last 256 MB of RAM are in
fact not usable, due to the overlap with the MBus Window address
range.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
ARM: mvebu: switch the Armada XP GP to use internal registers at 0xf1000000
Marvell has now provided bootloaders that are Device Tree capable for
the Armada XP GP board, and that also remap the internal register base
address to 0xf1000000. In addition, the bootloader now sets the MBus
Window base address to 0xf0000000, which allows to use much more RAM
in the last GB of RAM before the 4 GB limit (the entire space from
0xC0000000 to 0xFFFFFFFF was not usable due to being used for I/O, not
only the space from 0xF0000000 to 0xFFFFFFFF is used for I/O).
Therefore this commit:
* Updates the memory->reg Device Tree property with the fact that in
the first bank of RAM, memory up to 0xf0000000 can be used.
* Updates the soc->ranges Device Tree property with the fact that the
internal registers are now mapped at 0xf1000000.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
ARM: mvebu: switch the Armada XP DB to use internal registers at 0xf1000000
Marvell has now provided bootloaders that are Device Tree capable for
the Armada XP DB board, and that also remap the internal register base
address to 0xf1000000. In addition, the bootloader now sets the MBus
Window base address to 0xf0000000, but on this board, this change
doesn't make much difference since the board is by default equipped
with 2 GB of RAM.
Therefore this commit updates the soc->ranges Device Tree property
with the fact that the internal registers are now mapped at
0xf1000000.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
ARM: mvebu: change the default PCIe apertures for Armada 370/XP
The latest Marvell bootloaders for various boards change the MBus
Window base address from 0xC0000000 to 0xF0000000, in order to make
more RAM in the first 4 GB actually usable by the kernel (RAM that is
covered by the MBus window is "shadowed" and therefore not usable).
However, our default PCIe memory and I/O apertures where sitting at
0xe0000000 (for memory) and 0xe8000000 (for I/O), which will now be
outside of the MBus Window range on those platforms. To make things
work, we have to ensure those apertures use addresses in the
0xF0000000 -> 0xFFFFFFFF range.
Of course this change of the MBus Window base address from 0xC0000000
to 0xF0000000 also comes with a change of the internal register base
address from 0xD0000000 to 0xF1000000.
We have therefore designed the following memory map:
* 0xF0000000 -> 0xF1000000: 16 MB, used for NOR flashes on Armada XP
GP and Armada XP DB.
* 0xF1000000 -> 0xF1100000: 1 MB, used for internal registers.
* 0xF8000000 -> 0xFFE00000: 126 MB, used for PCIe memory.
* 0xFFE00000 -> 0xFFF00000: 1 MB, used for PCIe I/O.
* 0xFFF00000 -> 0xFFFFFFFF: 1 MB, used for the BootROM mapping
There is one exception to this layout: the Armada XP OpenBlocks, which
has a 128 MB NOR flash, mapped from 0xF0000000 to 0xF8000000. This
does not conflict with the current change for the PCIe I/O and memory
apertures, and continues to work because on Armada XP OpenBlocks, the
bootloader is an old one, and continues to have internal registers
mapped at 0xD0000000.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Andrew Lunn [Tue, 25 Feb 2014 17:34:00 +0000 (18:34 +0100)]
ARM: kirkwood: Add i2c alias so setting bus number
When using platform_driver instantiation, the i2c bus was given bus
number 0. The kirkwood-t5325 audio driver has this bus number hard
coded for the address of the codec. However by default device tree i2c
busses are dynamically allocated a bus number, starting from 1. Thus
the kirkwood-t5325 cannot find its audio codec. By adding an alias in
the DT file we can control the bus number and set it to 0. The codec
can then be found.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Jason Cooper [Tue, 25 Feb 2014 17:00:10 +0000 (17:00 +0000)]
ARM: mvebu: select dtbs from MACH_ARMADA_*
With kirkwood migrating into mach-mvebu, mvebu_v5_defconfig needs to
select ARCH_MVEBU. Unfortunately, this means that when building a v5
kernel, we unnecessarily build dtbs for the armada v7 boards.
To fix this, we instead select based on MACH_ARMADA_* on a per SoC basis.
Reported-by: Kevin Hilman <khilman@linaro.org> Acked-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Dove pinctrl uses additional registers to control MPPs. This patch first
increases existing pinctrl reg property by one register, and then adds
two new ranges for MPP4 and PMU MPP registers.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Andrew Lunn [Sat, 22 Feb 2014 19:14:59 +0000 (20:14 +0100)]
ARM: mvebu: Instantiate system controller in kirkwood.dtsi
Make use of the mvebu system controller, by placing a node into the
dtsi file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Arnd Bergmann <arnd@arndb.de> Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Andrew Lunn [Sat, 22 Feb 2014 19:14:53 +0000 (20:14 +0100)]
ARM: kirkwood: Instantiate L2 cache from DT.
Now that the Feroceon L2 cache has a DT binding, make use of it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Arnd Bergmann <arnd@arndb.de> Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Thu, 20 Feb 2014 11:11:31 +0000 (12:11 +0100)]
ARM: mvebu: use macros for interrupt flags on Armada 375/38x
Instead of hardcoding the values of the interrupt flags, use the
macros provided by <include/dt-bindings/interrupt-controller/irq.h>
and <include/dt-bindings/interrupt-controller/arm-gic.h> for the
Armada 375 and Armada 38x Device Tree files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Thu, 20 Feb 2014 11:11:30 +0000 (12:11 +0100)]
ARM: mvebu: use GIC_{SPI,PPI} in Armada 375/38x DTs
Instead of hardcoding 0 and 1 to indicate SPI and PPI GIC interrupts,
use the definitions of <dt-bindings/interrupt-controller/arm-gic.h> to
clarify the Device Tree code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Thu, 20 Feb 2014 11:11:29 +0000 (12:11 +0100)]
ARM: mvebu: use C preprocessor include for Armada 375/38x DTs
Some of the Armada 375/38x DTs that were recently submitted were still
using the old-style /include/ instead of the new-style, C-preprocessor
based #include. Since we are going to start including more headers,
switching to the C-preprocessor based includes is important.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Ben Peddell [Wed, 19 Feb 2014 20:02:37 +0000 (06:02 +1000)]
ARM: Kirkwood: Add support for many Synology NAS devices
Add device tree fragments and files to support many of the kirkwood
based Synology NAS devices. This is a modification of
Andrew Lunn's <andrew@lunn.ch> translation of the board setup file
maintained by Ben Peddell <klightspeed@killerwolves.net>
The Ricoh RS5C372 RTC was used in all 2009 units and some 2010 units.
All other Synology Kirkwood-based DiskStations and RackStations use
the Seiko S35390A RTC.
Most of the 1-bay and 2-bay units use the GPIOs that are multiplexed
with the built-in SATA interface activity/presence pins on mpp 20-23,
while the 4-bay units use ge01 and a PCIe SATA controller, and put the
software controlled HDD leds on mpp 36-43.
Most of the 6281 units with HDD power controls use mpp 29 and 31, while
most of the 6282 units with HDD power controls use mpp 30, 34, 44 and 45
and provide a model ID on mpp 28, 29, 46 and 47. Pre-2012 units and
most 4-bay units didn't have a separate power control for HDD1. These
power controls are presumably to limit startup current from the 12V
brick power supply.
Instead of using separate dtsi files in a synology directory, this
patch uses a single dtsi file containing all of the modules for
these boards, with all of the modules not common to all boards
disabled. The board dts files then enable the appropriate modules for
their boards.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Ben Peddell <klightspeed@killerwolves.net> Tested-by: Ben Peddell <klightspeed@killerwolves.net> (ds211j) Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Andrew Lunn [Wed, 19 Feb 2014 20:02:36 +0000 (06:02 +1000)]
DT: i2c: Trivial: Add sii,s35390a
Add the Seiko Instruments Inc S35390a to the list of trivial i2c
devices.
Signed-off-by: Ben Peddell <klightspeed@killerwolves.net> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Andrew Lunn [Wed, 19 Feb 2014 20:02:34 +0000 (06:02 +1000)]
DT: Vendor prefixes: Add ricoh, qnap, sii and synology
The following patches make use of vendor names:
* ricoh (Ricoh Co. Ltd.);
* qnap (QNAP Systems, Inc.);
* sii (Seiko Instruments, Inc.); and
* synology (Synology, Inc.)
Add them to the vendor prefix list.
Signed-off-by: Ben Peddell <klightspeed@killerwolves.net> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Jason Cooper <jason@lakedaemon.net> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Mon, 17 Feb 2014 14:23:29 +0000 (15:23 +0100)]
ARM: mvebu: add Device Tree for the Armada 385 DB board
The Armada 385 DB board is the development board from Marvell for the
Armada 385 SoC. This commit adds a Device Tree description for this
board, which enables the following features:
* Network interfaces
* I2C buses
* SDIO
* Serial port
* SPI bus, with a SPI flash
* PCIe interfaces
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Mon, 17 Feb 2014 14:23:28 +0000 (15:23 +0100)]
ARM: mvebu: add Device Tree description of the Armada 380/385 SoCs
The Armada 380 and 385 SoCs are new SoCs from Marvell, based on a
Cortex-A9 cores (single core for 380, dual core for 385) and a number
of hardware blocks that are common with earlier SoCs from the mvebu
family.
The provided Device Tree describes the following parts of the SoC:
* CPU
* Device Bus
* Clocks
* Interrupt controllers: GIC and MPIC
* GPIO controllers
* I2C buses
* L2 cache
* MBus controller
* Pinctrl
* Serial
* SPI buses
* System controller (for reboot)
* Timer
* XOR engines
* PCIe controllers
* Network interfaces
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Mon, 17 Feb 2014 14:23:26 +0000 (15:23 +0100)]
ARM: mvebu: add Device Tree for the Armada 375 DB board
The Armada 375 DB board is the development board from Marvell for the
Armada 375 SoC. This commit adds a Device Tree description for this
board, which enables the following features:
* I2C buses
* SDIO
* Serial port
* SPI bus, with a SPI flash. Note that the SPI bus is disabled by
default, because it conflicts with the NAND, and can only work if
the board boots out of SPI. Since most boards are shipped to boot
out of NAND, we're default to having the SPI bus disabled.
* PCIe interfaces
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Gregory CLEMENT [Mon, 17 Feb 2014 14:23:25 +0000 (15:23 +0100)]
ARM: mvebu: add Device Tree description of the Armada 375 SoC
The Armada 375 SoC is a new SoC from Marvell, based on a dual core
Cortex-A9 and a number of hardware blocks that are common with earlier
SoCs from the mvebu family.
The provided Device Tree describes the following parts of the SoC:
* CPUs
* Device Bus
* Clocks
* Interrupt controllers: GIC and MPIC
* GPIO controllers
* I2C buses
* L2 cache
* MBus controller
* SDIO
* Pinctrl
* SATA
* Serial
* SPI buses
* System controller (for reboot)
* Timer
* XOR engines
* PCIe controllers
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Ezequiel Garcia [Mon, 10 Feb 2014 23:00:34 +0000 (20:00 -0300)]
ARM: dove: Enable Dove watchdog in the devicetree
Add the devicetree node to enable watchdog support available in Dove SoCs.
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Ezequiel Garcia [Mon, 10 Feb 2014 23:00:33 +0000 (20:00 -0300)]
ARM: kirkwood: Add RSTOUT 'reg' entry to devicetree
In order to support multiplatform builds the watchdog devicetree binding
was modified and now the 'reg' property is specified to need two
entries. This commit adds the second entry as-per the new specification.
Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Andrew Lunn [Sat, 15 Feb 2014 12:59:53 +0000 (13:59 +0100)]
ARM: Kirkwood: convert rd88f6281-setup.c to DT.
Perform a mechanical translation of rd88f6281-setup.c into DT. Since
the hardware differs between the A0 and A1 stepping, two dts files are
used, and a .dtsi file for the common parts. The A0 part does not have
a "wan" port on the switch and uses PHY address 10 to address the
switch. The A1 part does have the "wan" port and uses address 0.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Wed, 12 Feb 2014 17:21:01 +0000 (18:21 +0100)]
ARM: mvebu: enable S/PDIF audio in Armada 370 DB Device Tree
In addition to the analog audio input and output, the Armada 370 DB
also has S/PDIF input and output optical connectors. This commit
improves the Device Tree description of the Armada 370 DB platform to
enable the S/PDIF support.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Wed, 12 Feb 2014 17:20:59 +0000 (18:20 +0100)]
ARM: mvebu: add I2C0 muxing option for Armada 370 SoC
This commit adds a pin-muxing configuration for the I2C0 bus of the
Armada 370, which is used on the Armada 370 DB platform to interface
with the CS42L51 audio codec.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Wed, 12 Feb 2014 17:20:58 +0000 (18:20 +0100)]
ARM: mvebu: add audio I2S controller to Armada 370 Device Tree
The Armada 370 SoC has an I2S audio controller. This commit adds the
description of this controller to the Device Tree describing this SoC,
as well as two possible muxing configurations for the I2S bus pins.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Tue, 11 Feb 2014 17:07:13 +0000 (18:07 +0100)]
ARM: mvebu: use input DT defines in Armada 370/XP boards
Instead of harcoding keycodes specifications in the Armada 370/XP
boards, use the <dt-bindings/input/input.h> header file and its
keycode definitions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Tue, 11 Feb 2014 17:07:12 +0000 (18:07 +0100)]
ARM: mvebu: use GPIO DT defines in Armada 370/XP boards
Instead of harcoding 0 and 1 for the gpio specifications in the Armada
370/XP boards, use the <dt-bindings/gpio/gpio.h> header file and its
GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW definitions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Andrew Lunn [Mon, 6 Jan 2014 22:49:17 +0000 (23:49 +0100)]
ARM: Kirkwood: Add DT description of QNAP 419
Re-implement the Marvell Kirkwood ts41x-setup.c in DT.
As with the QNAP 119, there are two variants, depending on which SoC
has been used. They differ on Ethernet PHY addresses and number of
PCIe busses.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Ian Campbell <ijc@hellion.org.uk> (kirkwood-ts419-6281.dtb) Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Linus Torvalds [Mon, 3 Feb 2014 00:32:53 +0000 (16:32 -0800)]
Merge branch 'parisc-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
"The three major changes in this patchset is a implementation for
flexible userspace memory maps, cache-flushing fixes (again), and a
long-discussed ABI change to make EWOULDBLOCK the same value as
EAGAIN.
parisc has been the only platform where we had EWOULDBLOCK != EAGAIN
to keep HP-UX compatibility. Since we will probably never implement
full HP-UX support, we prefer to drop this compatibility to make it
easier for us with Linux userspace programs which mostly never checked
for both values. We don't expect major fall-outs because of this
change, and if we face some, we will simply rebuild the necessary
applications in the debian archives"
* 'parisc-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: add flexible mmap memory layout support
parisc: Make EWOULDBLOCK be equal to EAGAIN on parisc
parisc: convert uapi/asm/stat.h to use native types only
parisc: wire up sched_setattr and sched_getattr
parisc: fix cache-flushing
parisc/sti_console: prefer Linux fonts over built-in ROM fonts
Mikulas Patocka [Tue, 28 Jan 2014 23:11:33 +0000 (00:11 +0100)]
hpfs: optimize quad buffer loading
HPFS needs to load 4 consecutive 512-byte sectors when accessing the
directory nodes or bitmaps. We can't switch to 2048-byte block size
because files are allocated in the units of 512-byte sectors.
Previously, the driver would allocate a 2048-byte area using kmalloc,
copy the data from four buffers to this area and eventually copy them
back if they were modified.
In the current implementation of the buffer cache, buffers are allocated
in the pagecache. That means that 4 consecutive 512-byte buffers are
stored in consecutive areas in the kernel address space. So, we don't
need to allocate extra memory and copy the content of the buffers there.
This patch optimizes the code to avoid copying the buffers. It checks
if the four buffers are stored in contiguous memory - if they are not,
it falls back to allocating a 2048-byte area and copying data there.
Mikulas Patocka [Tue, 28 Jan 2014 23:10:44 +0000 (00:10 +0100)]
hpfs: remember free space
Previously, hpfs scanned all bitmaps each time the user asked for free
space using statfs. This patch changes it so that hpfs scans the
bitmaps only once, remembes the free space and on next invocation of
statfs it returns the value instantly.
New versions of wine are hammering on the statfs syscall very heavily,
making some games unplayable when they're stored on hpfs, with load
times in minutes.
This should be backported to the stable kernels because it fixes
user-visible problem (excessive level load times in wine).
Helge Deller [Fri, 31 Jan 2014 21:19:52 +0000 (22:19 +0100)]
parisc: add flexible mmap memory layout support
Add support for the flexible mmap memory layout (as described in
http://lwn.net/Articles/91829). This is especially very interesting on
parisc since we currently only support 32bit userspace (even with a
64bit Linux kernel).
Guy Martin [Thu, 16 Jan 2014 16:17:53 +0000 (17:17 +0100)]
parisc: Make EWOULDBLOCK be equal to EAGAIN on parisc
On Linux, only parisc uses a different value for EWOULDBLOCK which
causes a lot of troubles for applications not checking for both values.
Since the hpux compat is long dead, make EWOULDBLOCK behave the same as
all other architectures.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be> Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 31 Jan 2014 22:00:38 +0000 (23:00 +0100)]
parisc: convert uapi/asm/stat.h to use native types only
The stat.h header file is exported to userspace. Some userspace
applications failed to compile due to missing/unknown types, so we
better convert it to use native types only (like it's done on other
architectures too).
Helge Deller [Fri, 31 Jan 2014 20:33:17 +0000 (21:33 +0100)]
parisc: fix cache-flushing
This commit: f8dae00684d678afa13041ef170cecfd1297ed40: parisc: Ensure full cache coherency for kmap/kunmap
caused negative caching side-effects, e.g. hanging processes with expect and
too many inequivalent alias messages from flush_dcache_page() on Debian 5 systems.
This patch now partly reverts it and has been in production use on our debian buildd
makeservers since a week without any major problems.
Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: John David Anglin <dave.anglin@bell.net> Cc: stable@vger.kernel.org # v3.9+ Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 31 Jan 2014 14:39:40 +0000 (15:39 +0100)]
parisc/sti_console: prefer Linux fonts over built-in ROM fonts
The built-in ROM fonts lack many necessary ASCII characters, which is
why it makes sens to prefer the Linux fonts instead if they are
available. This makes consoles on STI graphics cards which are not
supported by the stifb driver (e.g. Visualize FXe) looks much nicer.
Linus Torvalds [Sun, 2 Feb 2014 19:30:08 +0000 (11:30 -0800)]
Merge branch 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux
Pull SLAB changes from Pekka Enberg:
"Random bug fixes that have accumulated in my inbox over the past few
months"
* 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
mm: Fix warning on make htmldocs caused by slab.c
mm: slub: work around unneeded lockdep warning
mm: sl[uo]b: fix misleading comments
slub: Fix possible format string bug.
slub: use lockdep_assert_held
slub: Fix calculation of cpu slabs
slab.h: remove duplicate kmalloc declaration and fix kernel-doc warnings
Linus Torvalds [Sun, 2 Feb 2014 19:28:48 +0000 (11:28 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: introduce -s to dump counters
tools/power turbostat: remove unused command line option
turbostat: Add option to report joules consumed per sample
turbostat: run on HSX
turbostat: Add a .gitignore to ignore the compiled turbostat binary
turbostat: Clean up error handling; disambiguate error messages; use err and errx
turbostat: Factor out common function to open file and exit on failure
turbostat: Add a helper to parse a single int out of a file
turbostat: Check return value of fscanf
turbostat: Use GCC's CPUID functions to support PIC
turbostat: Don't attempt to printf an off_t with %zx
turbostat: Don't put unprocessed uapi headers in the include path
Linus Torvalds [Sun, 2 Feb 2014 19:11:06 +0000 (11:11 -0800)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's a set of patches for (hopefully) -rc1. Some of them are fixes,
but a good number of them also do things such as enable new drivers in
the defconfigs for platforms that have such devices, increases
coverage of the multiplatform defconfig and some DTS changes that
plumbs up some of the devices that now have bindings and driver
support.
The commit dates are recent; we've mostly collected these fixes in the
last few days but I also had to rebuild the branch yesterday to sort
out some internal conflicts which reset the timestamps. The changes
should have been tested by each platform maintainer already (and few
of them have cross-platform impact) so I'm personally not too
concerned by it at this time"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: multi_v7_defconfig: remove redundant entries and re-enable TI_EDMA
ARM: multi_v7_defconfig: add mvebu drivers
clocksource: kona: Add basic use of external clock
drivers: bus: fix CCI driver kcalloc call parameters swap
ARM: dts: bcm28155-ap: Fix Card Detection GPIO
ARM: multi_v7_defconfig: Select CONFIG_AT803X_PHY
ARM: keystone: config: fix build warning when CONFIG_DMADEVICES is not set
MAINTAINERS: ARM: SiRF: use regex patterns to involve all SiRF drivers
ARM: dts: zynq: Add SDHCI nodes
ARM: hisi: don't select SMP
ARM: tegra: rebuild tegra_defconfig to add DEBUG_FS
ARM: multi_v7: copy most options from tegra_defconfig
ARM: iop32x: fix power off handling for the EM7210 board
ARM: integrator: restore static map on the CP
ARM: msm_defconfig: Enable MSM clock drivers
ARM: dts: msm: Add clock controller nodes and hook into uart
ARM: OMAP4+: move errata initialization to omap4_pm_init_early
ARM: OMAP4460: cpuidle: Extend PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD on cpuidle
ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP)
ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference
...
Jean Delvare [Sun, 2 Feb 2014 16:59:07 +0000 (17:59 +0100)]
hwmon: Fix SENSORS_TMP102 dependencies to eliminate build errors
Similar to what was done for the lm75 driver.
Add depends on THERMAL since that is what provides the
register/unregister functions above, but only if THERMAL_OF was
selected as this is an optional feature of the driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Randy Dunlap <rdunlap@infradead.org> Acked-by: Eduardo Valentin <eduardo.valentin@ti.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Jean Delvare [Sun, 2 Feb 2014 16:59:07 +0000 (17:59 +0100)]
hwmon: Fix SENSORS_LM75 dependencies to eliminate build errors
Based on an earlier attempt by Randy Dunlap.
Fix SENSORS_LM75 dependencies to eliminate build errors:
drivers/built-in.o: In function `lm75_remove':
lm75.c:(.text+0x12bd8c): undefined reference to `thermal_zone_of_sensor_unregister'
drivers/built-in.o: In function `lm75_probe':
lm75.c:(.text+0x12c123): undefined reference to `thermal_zone_of_sensor_register'
Add depends on THERMAL since that is what provides the
register/unregister functions above, but only if THERMAL_OF was
selected as this is an optional feature of the driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Randy Dunlap <rdunlap@infradead.org> Acked-by: Eduardo Valentin <eduardo.valentin@ti.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Linus Torvalds [Sat, 1 Feb 2014 19:03:16 +0000 (11:03 -0800)]
Merge branch 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull misc kbuild changes from Michal Marek:
"The non-critical part of kbuild is small this time:
- Three fixes for make deb-pkg
- A new coccinelle check
One of the deb-pkg fixes is a leftover from the last merge window,
hence the merge commit"
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
deb-pkg: Fix building for MIPS big-endian or ARM OABI
deb-pkg: Fix cross-building linux-headers package
scripts: Coccinelle script for pm_runtime_* return checks with IS_ERR_VALUE
deb-pkg: Inhibit initramfs builders if CONFIG_BLK_DEV_INITRD is not set
Pali Rohár [Tue, 28 Jan 2014 20:26:44 +0000 (20:26 +0000)]
afs: proc cells and rootcell are writeable
Both proc files are writeable and used for configuring cells. But
there is missing correct mode flag for writeable files. Without
this patch both proc files are read only.
[ It turns out they aren't really read-only, since root can write to
them even if the write bit isn't set due to CAP_DAC_OVERRIDE ]
Heiko Carstens [Fri, 31 Jan 2014 06:50:36 +0000 (07:50 +0100)]
tile: remove compat_sys_lookup_dcookie declaration to fix compile error
With commit d8d14bd09cdd ("fs/compat: fix lookup_dcookie() parameter
handling") I changed the type of the len parameter of the
lookup_dcookie() syscall.
However I missed that there was still a stale declaration in
arch/tile/.. which now causes a compile error on tile:
In file included from fs/dcookies.c:28:0:
include/linux/compat.h:425:17: error: conflicting types for 'compat_sys_lookup_dcookie'
fs/dcookies.c:207:1: error: conflicting types for 'compat_sys_lookup_dcookie'
Simply remove the declaration in the tile architecture, which is only a
leftover from before the different compat lookup_dcookie() versions have
been merged. The correct declaration is now in include/linux/compat.h
The build error was reported by Fenguang's build bot.
Linus Torvalds [Sat, 1 Feb 2014 18:52:45 +0000 (10:52 -0800)]
Merge branch 'for-linus' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"A set of cifs fixes (mostly for symlinks, and SMB2 xattrs) and
cleanups"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix check for regular file in couldbe_mf_symlink()
[CIFS] Fix SMB2 mounts so they don't try to set or get xattrs via cifs
CIFS: Cleanup cifs open codepath
CIFS: Remove extra indentation in cifs_sfu_type
CIFS: Cleanup cifs_mknod
CIFS: Cleanup CIFSSMBOpen
cifs: Add support for follow_link on dfs shares under posix extensions
cifs: move unix extension call to cifs_query_symlink()
cifs: Re-order M-F Symlink code
cifs: Add create MFSymlinks to protocol ops struct
cifs: use protocol specific call for query_mf_symlink()
cifs: Rename MF symlink function names
cifs: Rename and cleanup open_query_close_cifs_symlink()
cifs: Fix memory leak in cifs_hardlink()
Linus Torvalds [Sat, 1 Feb 2014 18:43:45 +0000 (10:43 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"Several obvious fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Fix mountpoint reference leakage in linkat
hfsplus: use xattr handlers for removexattr
Typo in compat_sys_lseek() declaration
fs/super.c: sync ro remount after blocking writers
vfs: unexport the getname() symbol
Linus Torvalds [Sat, 1 Feb 2014 18:29:59 +0000 (10:29 -0800)]
Merge tag 'staging-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull rtl8812ae staging wireless driver from Greg KH:
"Here's a single staging driver for a wireless chipset that has shown
up in the SteamBox hardware. It is merged separately from the "main"
staging pull request to sync up with the wireless api changes that
came in from the networking tree.
It's self-contained and works for me and others. Larry will be
replacing it with a "real" driver for 3.15, but for now this one is
needed"
* tag 'staging-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8821ae: Enable build by reverting BROKEN marking
staging: r8821ae: Fix build problems
Staging: rtl8812ae: disable due to build errors
Staging: rtl8821ae: add TODO file
Staging: rtl8821ae: removed unused functions and variables
Staging: rtl8821ae: rc.c: fix up function prototypes
Staging: rtl8812ae: Add Realtek 8821 PCI WIFI driver
Revert "PCI: Remove from bus_list and release resources in pci_release_dev()"
Revert commit ef83b0781a73 "PCI: Remove from bus_list and release
resources in pci_release_dev()" that made some nasty race conditions
become possible. For example, if a Thunderbolt link is unplugged
and then replugged immediately, the pci_release_dev() resulting from
the hot-remove code path may be racing with the hot-add code path
which after that commit causes various kinds of breakage to happen
(up to and including a hard crash of the whole system).
Moreover, the problem that commit ef83b0781a73 attempted to address
cannot happen any more after commit 8a4c5c329de7 "PCI: Check parent
kobject in pci_destroy_dev()", because pci_destroy_dev() will now
return immediately if it has already been executed for the given
device.
Note, however, that the invocation of msi_remove_pci_irq_vectors()
removed by commit ef83b0781a73 from pci_free_resources() along with
the other changes made by it is not added back because of subsequent
code changes depending on that modification.
Fixes: ef83b0781a73 (PCI: Remove from bus_list and release resources in pci_release_dev()) Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olof Johansson [Fri, 31 Jan 2014 23:21:08 +0000 (15:21 -0800)]
ARM: multi_v7_defconfig: remove redundant entries and re-enable TI_EDMA
TI_EDMA fell out of automatically selected options in the multi_v7
defconfig due to a select being removed from the davinci Kconfig entry. So
we need to re-enable explicitly to not regress some platforms.
The rest is just the result of running 'make multi_v7_defconfig + make
savedefconfig' to remove entries that are no longer needed due to changed
dependencies/selects or defaults.
Olof Johansson [Fri, 31 Jan 2014 23:20:07 +0000 (15:20 -0800)]
ARM: multi_v7_defconfig: add mvebu drivers
Recent boot farm testing has highlighted some issues with mvebu and
multiplatform kernels. Increase the test coverage so we can discover
these issues earlier.
Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Olof Johansson <olof@lixom.net>
Tim Kryger [Thu, 5 Dec 2013 19:20:43 +0000 (11:20 -0800)]
clocksource: kona: Add basic use of external clock
When an clock is specified in the device tree, enable it and use it to
determine the external clock frequency.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org> Reviewed-by: Markus Mayer <markus.mayer@linaro.org> Reviewed-by: Matt Porter <matt.porter@linaro.org> Reviewed-by: Christian Daudt <bcm@fixthebug.org> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Christian Daudt <bcm@fixthebug.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Fri, 31 Jan 2014 23:39:07 +0000 (15:39 -0800)]
Merge tag 'nfs-for-3.14-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights:
- Fix several races in nfs_revalidate_mapping
- NFSv4.1 slot leakage in the pNFS files driver
- Stable fix for a slot leak in nfs40_sequence_done
- Don't reject NFSv4 servers that support ACLs with only ALLOW aces"
* tag 'nfs-for-3.14-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
nfs: initialize the ACL support bits to zero.
NFSv4.1: Cleanup
NFSv4.1: Clean up nfs41_sequence_done
NFSv4: Fix a slot leak in nfs40_sequence_done
NFSv4.1 free slot before resending I/O to MDS
nfs: add memory barriers around NFS_INO_INVALID_DATA and NFS_INO_INVALIDATING
NFS: Fix races in nfs_revalidate_mapping
sunrpc: turn warn_gssd() log message into a dprintk()
NFS: fix the handling of NFS_INO_INVALID_DATA flag in nfs_revalidate_mapping
nfs: handle servers that support only ALLOW ACE type.
Linus Torvalds [Fri, 31 Jan 2014 23:38:09 +0000 (15:38 -0800)]
Merge tag 'sound-fix-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The big chunks here are the updates for oxygen driver for Xonar DG
devices, which were slipped from the previous pull request. They are
device-specific and thus not too dangerous.
Other than that, all patches are small bug fixes, mainly for Samsung
build fixes, a few HD-audio enhancements, and other misc ASoC fixes.
(And this time ASoC merge is less than Octopus, lucky seven :)"
* tag 'sound-fix-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (42 commits)
ALSA: hda/hdmi - allow PIN_OUT to be dynamically enabled
ALSA: hda - add headset mic detect quirks for another Dell laptop
ALSA: oxygen: Xonar DG(X): cleanup and minor changes
ALSA: oxygen: Xonar DG(X): modify high-pass filter control
ALSA: oxygen: Xonar DG(X): modify input select functions
ALSA: oxygen: Xonar DG(X): modify capture volume functions
ALSA: oxygen: Xonar DG(X): use headphone volume control
ALSA: oxygen: Xonar DG(X): modify playback output select
ALSA: oxygen: Xonar DG(X): capture from I2S channel 1, not 2
ALSA: oxygen: Xonar DG(X): move the mixer code into another file
ALSA: oxygen: modify CS4245 register dumping function
ALSA: oxygen: modify adjust_dg_dac_routing function
ALSA: oxygen: Xonar DG(X): modify DAC/ADC parameters function
ALSA: oxygen: Xonar DG(X): modify initialization functions
ALSA: oxygen: Xonar DG(X): add new CS4245 SPI functions
ALSA: oxygen: additional definitions for the Xonar DG/DGX card
ALSA: oxygen: change description of the xonar_dg.c file
ALSA: oxygen: export oxygen_update_dac_routing symbol
ALSA: oxygen: add mute mask for the OXYGEN_PLAY_ROUTING register
ALSA: oxygen: modify the SPI writing function
...
Linus Torvalds [Fri, 31 Jan 2014 23:31:23 +0000 (15:31 -0800)]
Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- add support for SCSI Referrals (Hannes)
- add support for T10 DIF into target core (nab + mkp)
- add support for T10 DIF emulation in FILEIO + RAMDISK backends (Sagi + nab)
- add support for T10 DIF -> bio_integrity passthrough in IBLOCK backend (nab)
- prep changes to iser-target for >= v3.15 T10 DIF support (Sagi)
- add support for qla2xxx N_Port ID Virtualization - NPIV (Saurav + Quinn)
- allow percpu_ida_alloc() to receive task state bitmask (Kent)
- fix >= v3.12 iscsi-target session reset hung task regression (nab)
- fix >= v3.13 percpu_ref se_lun->lun_ref_active race (nab)
- fix a long-standing network portal creation race (Andy)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (51 commits)
target: Fix percpu_ref_put race in transport_lun_remove_cmd
target/iscsi: Fix network portal creation race
target: Report bad sector in sense data for DIF errors
iscsi-target: Convert gfp_t parameter to task state bitmask
iscsi-target: Fix connection reset hang with percpu_ida_alloc
percpu_ida: Make percpu_ida_alloc + callers accept task state bitmask
iscsi-target: Pre-allocate more tags to avoid ack starvation
qla2xxx: Configure NPIV fc_vport via tcm_qla2xxx_npiv_make_lport
qla2xxx: Enhancements to enable NPIV support for QLOGIC ISPs with TCM/LIO.
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
IB/isert: pass scatterlist instead of cmd to fast_reg_mr routine
IB/isert: Move fastreg descriptor creation to a function
IB/isert: Avoid frwr notation, user fastreg
IB/isert: seperate connection protection domains and dma MRs
tcm_loop: Enable DIF/DIX modes in SCSI host LLD
target/rd: Add DIF protection into rd_execute_rw
target/rd: Add support for protection SGL setup + release
target/rd: Refactor rd_build_device_space + rd_release_device_space
target/file: Add DIF protection support to fd_execute_rw
target/file: Add DIF protection init/format support
...
Barry Song [Fri, 3 Jan 2014 03:24:13 +0000 (11:24 +0800)]
MAINTAINERS: ARM: SiRF: use regex patterns to involve all SiRF drivers
instead of listing drivers one by one, use regex patterns to involve all
SiRF drivers directly.
this also adds sirf UART and watchdog drivers automatically from:
drivers/tty/serial/sirfsoc_uart.*
drivers/watchdog/sirfsoc_wdt.c
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: Wim Van Sebroeck <wim@iguana.be> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 31 Jan 2014 22:59:28 +0000 (14:59 -0800)]
Merge tag 'mvebu-fixes-3.13-2' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for v3.13 (incremental #2)
- allow building and booting DT and non-DT plat-orion SoCs
- catch proper return value for kirkwood_pm_init()
- properly check return of of_iomap to solve boot hangs (mirabox, others)
- remove a compile warning on Armada 370 with non-SMP.
* tag 'mvebu-fixes-3.13-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP)
ARM: mvebu: Fix kernel hang in mvebu_soc_id_init() when of_iomap failed
ARM: kirkwood: kirkwood_pm_init() should return void
ARM: orion: provide C-style interrupt handler for MULTI_IRQ_HANDLER
Stephen Warren [Sat, 25 Jan 2014 03:13:28 +0000 (20:13 -0700)]
ARM: tegra: rebuild tegra_defconfig to add DEBUG_FS
DEBUG_FS used to be selected by COMMON_CLK_DEBUG, which was enabled
by tegra_defconfig. However, this config option no longer exists, so
no longer selects DEBUG_FS, and nothing else selects it either. So,
"make tegra_defconfig" no longer enables DEBUG_FS in .config.
Rebuild tegra_defconfig on top of next-20140424, while manually
re-enabling DEBUG_FS.
Reasons for removed entries are:
- I2C_MUX: selected by MEDIA_SUBDRV_AUTOSELECT
- DRM_PANEL: selected by DRM_TEGRA
- NEW_LEDS: selected by many things; at least VT
- LEDS_CLASS: selected by many things; at least VT
- LEDS_TRIGGERS: selected by many things; at least VT
- COMMON_CLK_DEBUG: no longer exists
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Kevin Hilman <khilman@linaro.org>
Stephen Warren [Fri, 20 Dec 2013 20:41:32 +0000 (13:41 -0700)]
ARM: multi_v7: copy most options from tegra_defconfig
multi_v7_defconfig was missing a large number of options that were in
tegra_defconfig. This patch adds them. The changes fall into the
following categories:
* Enable more Tegra SoC options/drivers.
* Enable more drivers for Tegra boards.
* Enable more options that are useful for running distros.
The patch removes a few lines as well, simply because those options are
now selected by something else, and "make savedefconfig" removes them. I
verified that the options appear in .config after
"make multi_v7_defconfig".
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Walleij [Wed, 29 Jan 2014 14:20:15 +0000 (15:20 +0100)]
ARM: iop32x: fix power off handling for the EM7210 board
This board was missed when converting all the others to proper
abstracted GPIO handling. Fix it up the right way by requesting
and driving GPIO line 0 high through gpiolib to power off the
machine.
Linus Walleij [Fri, 24 Jan 2014 13:04:28 +0000 (14:04 +0100)]
ARM: integrator: restore static map on the CP
Commit 78d1632183454dba46ca8295484a5e7603acdc18 deleted the
static mappings of the core modules, but this static map is
still needed on the Integrator/CP (not the Integrator/AP).
Restore the static map on the Integrator/CP.
Reported-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Stephen Boyd [Fri, 17 Jan 2014 01:25:04 +0000 (17:25 -0800)]
ARM: msm_defconfig: Enable MSM clock drivers
This allows us to probe the clock controller devices and boot to a
serial console on all DT enabled MSM platforms.
Cc: David Brown <davidb@codeaurora.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Stephen Boyd [Fri, 17 Jan 2014 01:25:03 +0000 (17:25 -0800)]
ARM: dts: msm: Add clock controller nodes and hook into uart
Add the necessary DT nodes to probe the clock controllers on MSM
devices as well as hook up the uart nodes to the clock
controllers. This should allow us to boot to a serial console on
all DT enabled MSM platforms.
Cc: David Brown <davidb@codeaurora.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Nishanth Menon [Mon, 20 Jan 2014 20:06:37 +0000 (14:06 -0600)]
ARM: OMAP4+: move errata initialization to omap4_pm_init_early
Move all OMAP4 PM errata initializations to centralized location in
omap4_pm_init_early. This allows for users to utilize the erratas
in various submodules as needed.
Reported-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Nishanth Menon <nm@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
ARM: OMAP4460: cpuidle: Extend PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD on cpuidle
The same workaround as ff999b8a0983ee15668394ed49e38d3568fc6859
"ARM: OMAP4460: Workaround for ROM bug because of CA9 r2pX GIC ..."
need to be applied not only when system is booting, but when MPUSS hits
OSWR state through CPUIdle too. Without this WA the same issue is
reproduced now on boards PandaES and Tablet/Blaze with SOM OMAP4460
when CONFIG_CPU_IDLE is enabled.
After MPUSS has enterred OSWR and waken up:
- GIC distributor became disabled forever
- scheduling is not performed any more
Cc: Kevin Hilman <khilman@linaro.org> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Reported-by: Taras Kondratiuk <taras.kondratiuk@linaro.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Oleg Drokin [Fri, 31 Jan 2014 20:41:58 +0000 (15:41 -0500)]
Fix mountpoint reference leakage in linkat
Recent changes to retry on ESTALE in linkat
(commit 442e31ca5a49e398351b2954b51f578353fdf210)
introduced a mountpoint reference leak and a small memory
leak in case a filesystem link operation returns ESTALE
which is pretty normal for distributed filesystems like
lustre, nfs and so on.
Free old_path in such a case.
[AV: there was another missing path_put() nearby - on the previous
goto retry]
Signed-off-by: Oleg Drokin: <green@linuxhacker.ru> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Fri, 31 Jan 2014 22:25:52 +0000 (14:25 -0800)]
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pyll ARM64 patches from Catalin Marinas:
- Build fix with DMA_CMA enabled
- Introduction of PTE_WRITE to distinguish between writable but clean
and truly read-only pages
- FIQs enabling/disabling clean-up (they aren't used on arm64)
- CPU resume fix for the per-cpu offset restoring
- Code comment typos
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: Introduce PTE_WRITE
arm64: mm: Remove PTE_BIT_FUNC macro
arm64: FIQs are unused
arm64: mm: fix the function name in comment of cpu_do_switch_mm
arm64: fix build error if DMA_CMA is enabled
arm64: kernel: fix per-cpu offset restore on resume
arm64: mm: fix the function name in comment of __flush_dcache_area
arm64: mm: use ubfm for dcache_line_size
Linus Torvalds [Fri, 31 Jan 2014 22:24:56 +0000 (14:24 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha
Pull alpha updates from Matt Turner:
"A pair of changes for alpha. One fixes a networking regression, and
the second adds audit syscall support which will help in supporting
systemd"
hfsplus was already using the handlers for get and set operations,
and with the removal of can_set_xattr we've now allow operations that
wouldn't otherwise be allowed.
With this we can also centralize the special-casing of the osx.
attrs that don't have prefixes on disk in the osx xattr handlers.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
projects / linux-beck.git / log