The firmware keeps track of channel usage. This data can
be used by the automatic channel selection to find the best
channel.
Survey data from wlan4
frequency: 5200 MHz [in use]
noise: -91 dBm
channel active time: 811909 ms
channel busy time: 63395 ms
channel transmit time: 59636 ms
Survey data from wlan4
frequency: 5210 MHz
noise: -91 dBm
channel active time: 121 ms
channel busy time: 119 ms
channel transmit time: 0 ms
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Tue, 16 Aug 2011 19:44:21 +0000 (21:44 +0200)]
b43: warn when forcing PIO mode
We have resolved all the known issues with DMA mode, however some users
(or distros) are still forcing PIO mode by config files. Without
debugging enabled it's not noticable at all. Add the warning for them.
Cc: Gregory Bellier <gregory.bellier@gmail.com> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware keeps track of channel usage. This data can
be used by the automatic channel selection to find the
*best* channel.
Survey data from wlan22
frequency: 2412 MHz [in use]
noise: -86 dBm
channel active time: 3339608 ms
channel busy time: 270982 ms
channel transmit time: 121515 ms
Survey data from wlan22
frequency: 2417 MHz
noise: -86 dBm
channel active time: 70 ms
channel busy time: 2 ms
channel transmit time: 1 ms
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
carl9170: fix timekeeping for HW_COUNTER firmwares
AR9170_PWR_REG_PLL_ADDAC is used to set the main clock
divisor which affects the AHB/CPU speed. Because this
would interfere with the firmware internal timekeeping,
the function has to be moved into the firmware.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sun, 14 Aug 2011 21:27:30 +0000 (23:27 +0200)]
b43: LCN-PHY: switch analog
Analog is switched on right after reading PHY version:
read16 0xfaafc3e0 -> 0xa801
phy_read(0x043b) -> 0x0000
phy_write(0x043b) <- 0x0000
Switched off after after killing radio:
>>> Switch Radio(OFF) end
phy_read(0x043c) -> 0x0000
phy_write(0x043c) <- 0x0007
phy_read(0x043b) -> 0x0000
phy_write(0x043b) <- 0x0007
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 13 Aug 2011 16:13:49 +0000 (10:13 -0600)]
ath9k: remove a bogus WARN_ON
On embedded hardware it's normal to not have a PCI device for the PCI
bridge that the wifi card is attached to. pdev->bus->self will be
NULL in that case. In that case, simply return without emitting an
useless kernel stack trace.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: Fix invalid noisefloor reading due to channel update
While switching b/w HT20/40, the current channel's nf values
are updated into history buffer. Since the current channel's
channel type, channel flag got updated before reading
nf value from hw. This channel type mismatch is causing invalid
readings when hw is on ht20 but getnf tries to read on extn chains.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: Fix noisefloor history update for extn chains
Before doing hw reset the current channel's noisefloor readings
are updated into history buffer. The extension chain's readings
are considered only if the current channel was configured in HT40.
While moving from HT40 to HT20, the extn chain's readings are
skipped though the current channel is in ht40. This patch updates
extn chain reading based on channel flag.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever RXEOL is received, both RXORN and RXEOL got cleared
to avoid rx overrun interrupt storm. This was handled only for
edma chips. The same scenario was also observered with AR9280,
doing frequent channel type switch b/w HT20/40 with bidi traffic
that is causing failure to stop rx dma. This patch clears
the RXEOL & RXORN interrupts for all chips.
ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020
DMADBG_7=0x000062c0
ath: Could not stop RX, we could be confusing the DMA engine when we
start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:532
ath_stoprecv+0x110/0x120 [ath9k]()
Call Trace:
[<ffffffff8104a55a>] warn_slowpath_common+0x7a/0xb0
[<ffffffff8104a5a5>] warn_slowpath_null+0x15/0x20
[<ffffffffa0560380>] ath_stoprecv+0x110/0x120 [ath9k]
[<ffffffffa055e6fa>] ath_reset+0x6a/0x200 [ath9k]
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw: Fix exceed transmission burst-time of 5GHz
The WAR which adds extra delimiters when using RTS/CTS
with aggregation and non-enterprise AR9003 chips.
This extra padding is done after doing all the 4ms limit
checks and hence the total aggregate sizes are exceeding
the allowed duration. This patch limits the aggregate
sizes appropriately after including these extra delimiters.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Tue, 9 Aug 2011 23:45:11 +0000 (16:45 -0700)]
{nl,cfg,mac}80211: let userspace make meshif mesh gate
Allow userspace to set NL80211_MESHCONF_GATE_ANNOUNCEMENTS attribute,
which will advertise this mesh node as being a mesh gate.
NL80211_HWMP_ROOTMODE must be set or this will do nothing.
Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Tue, 9 Aug 2011 23:45:08 +0000 (16:45 -0700)]
mac80211: mesh gate implementation
In this implementation, a mesh gate is a root node with a certain bit
set in its RANN flags. The mpath to this root node is marked as a path
to a gate, and added to our list of known gates for this if_mesh. Once a
path discovery process fails, we forward the unresolved frames to a
known gate. Thanks to Luis Rodriguez for refactoring and bug fix help.
Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Tue, 9 Aug 2011 23:45:06 +0000 (16:45 -0700)]
mac80211: mesh locking fixes
mesh_queue_preq is invoked invoked from both user (work queue) and
softirq (timer) context, so the _bh version of spinlock needs to be
used. Also, the mpath->state_lock should be softirq safe as well.
Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stefan Assmann [Sat, 13 Aug 2011 10:12:36 +0000 (12:12 +0200)]
rtlwifi: add module parameter to set global debug level
No need to recompile the module anymore to set the debug level.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Fri, 12 Aug 2011 23:41:11 +0000 (01:41 +0200)]
b43: HT-PHY: init: add missing PHY mask/set ops
MMIO hacks were used to trick ndis&wl. For example following:
phy_read(0x0280) -> 0xffff
phy_write(0x0280) <- 0xff3e
***
phy_read(0x0280) -> 0x0000
phy_write(0x0280) <- 0x003e
was translated to mask 0xff00 and set 0x3e.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: Traffic to clients gets affected when one client leaves a cyrpto bss
When a client disassociates from a crypto enabled bss, data traffic to
other clients connected to the bss is stalled. This was due to a boolean
variable used to keep track if HW crypto is enabled i.e. if set key has
been called to add a key. This flag was being reset every time delete
key was called e.g when a station leaves the bss. Once the flag is
reset, rx status flags were not being set for connected clients which
disrupts traffic to these clients. Fix this issue by not resetting the
flag since we do not need to reset this flag during the life time of the
bss.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thomas Pedersen [Sat, 13 Aug 2011 03:01:00 +0000 (20:01 -0700)]
mac80211: update mesh peering frame format
This patch updates the mesh peering frames to the format specified in
the recently ratified 802.11s standard. Several changes took place to
make this happen:
- Change RX path to handle new self-protected frames
- Add new Peering management IE
- Remove old Peer Link IE
- Remove old plink_action field in ieee80211_mgmt header
These changes by themselves would either break peering, or work by
coincidence, so squash them all into this patch.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thomas Pedersen [Fri, 12 Aug 2011 02:35:10 +0000 (19:35 -0700)]
mac80211: fix mesh beacon format
Correct ordering of IEs in the mesh beacon while removing unneeded IEs
from mesh peering frames. Set privacy bit in capability info if security
is enabled. Add utility functions to aid in construction
of IEs and reduce code duplication.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Thu, 11 Aug 2011 21:46:44 +0000 (23:46 +0200)]
bcma: implement BCM4331 workaround for external PA lines
We need to disable ext. PA lines for reading SPROM. It's disabled by
default, but this patch allows using bcma after loading wl, which leaves
workaround enabled.
Cc: Arend van Spriel <arend@broadcom.com> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Thu, 11 Aug 2011 14:17:42 +0000 (16:17 +0200)]
mac80211: Tear down BA session on BAR tx failure
As described at [1] some STAs (i.e. Intel 5100 Windows) can end up
correctly BlockAcking incoming frames without delivering them to user
space if a AMPDU subframe got lost and we don't flush the receipients
reorder buffer with a BlockAckReq. This in turn results in stuck
connections.
According to 802.11n-2009 it is not necessary to send a BAR to flush
the recepients RX reorder buffer but we still do that to be polite.
However, assume the following frame exchange:
AP -> STA, AMPDU (failed)
AP -> STA, BAR (failed)
The client in question then ends up in the same situation and won't
deliver frames to userspace anymore since we weren't able to flush
its reorder buffer.
This is not a hypothetical situation but I was able to observe this
exact behavior during a stress test between a rt2800pci AP and a Intel
5100 Windows client.
In order to work around this issue just tear down the BA session as
soon as a BAR failed to be TX'ed.
Felix Fietkau [Wed, 10 Aug 2011 19:50:30 +0000 (13:50 -0600)]
b43: reload phy and bss settings after core restarts
b43_op_config and b43_op_bss_info_changed apply many settings by directly
writing to hardware registers. These settings are lost as soon as the core
is restarted and the initvals are reloaded. This was discovered because
restarting hostapd led to the beacon interval getting set to ~33s (see
https://dev.openwrt.org/ticket/8033 for more information).
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: do btcoex ASPM disabling at initialization time
Disable ASPM in pci ->probe on upstream (device) and downstream
(PCIe port) component. According to e1000e driver authors this is
required. I did not find that requirement in PCIe spec, but it seems
to be logical for me.
This need to be fixed for CONFIG_PCIEASPM, that will be done later ...
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Fri, 12 Aug 2011 18:45:44 +0000 (21:45 +0300)]
staging: remove ath6kl
ath6kl is now in drivers/net/wireless/ath so the staging driver
is not supported anymore and should be removed.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Greg KH <gregkh@suse.de> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Thu, 11 Aug 2011 01:53:57 +0000 (18:53 -0700)]
mwifiex: use cfg80211 dynamic scan table and cfg80211_get_bss API
Instead of maintaining static scan table in driver, scan list is sent
to cfg80211 stack (after parsing each scan command response).
In assoc handler (for infra and ibss network) requested BSS information
is retrieved using cfg80211_get_bss() API.
With the changes above some redundant code are removed.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 10 Aug 2011 21:23:35 +0000 (15:23 -0600)]
ath9k: avoid sending a-mpdu packets to sleeping stations
If the driver gets a tx status report for an A-MPDU sent to a station that
just went to sleep, that leaves a race condition where this tx status can
trigger another A-MPDU transmission.
To fix this, check if the station is sleeping before queueing the tid.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Wed, 10 Aug 2011 20:55:56 +0000 (23:55 +0300)]
nl80211/cfg80211: Add extra IE configuration to AP mode setup
The NL80211_CMD_NEW_BEACON command is, in practice, requesting AP mode
operations to be started. Add new attributes to provide extra IEs
(e.g., WPS IE, P2P IE) for drivers that build Beacon, Probe Response,
and (Re)Association Response frames internally (likely in firmware).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Wed, 10 Aug 2011 20:54:35 +0000 (23:54 +0300)]
nl80211/cfg80211: Add crypto settings into NEW_BEACON
This removes need from drivers to parse the beacon tail/head data
to figure out what crypto settings are to be used in AP mode in case
the Beacon and Probe Response frames are fully constructed in the
driver/firmware.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211/mac80211: move information element parsing logic to cfg80211
Moving the parsing logic for retrieving the information elements
stored in management frames, e.g. beacons or probe responses,
and making it available to other cfg80211 drivers.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Marek Lindner [Wed, 3 Aug 2011 14:35:16 +0000 (16:35 +0200)]
ath9k: remove eeprom txgain override for minor version < 19
ath9k_hw_4k_get_eeprom() overrides the eeprom value for txgain if the
minor version is not 19 or above with a value of 0.
ar9002_hw_init_mode_gain_regs() relies on this information to
determine whether this is a high power wifi card or not. The override
caused the driver to always use the 'normal' power tables even for
high power devices if their minor version was not high enough. Thus
leading to reduced power output.
This isn't needed for the AR9285; the check originated with the
AR9280 setup code which requires the EEPROM version check.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Acked-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Adrian Chadd <adrian@freebsd.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Thu, 11 Aug 2011 08:46:22 +0000 (11:46 +0300)]
nl80211/cfg80211: Make addition of new sinfo fields safer
Add a comment pointing out the use of enum station_info_flags for
all new struct station_info fields. In addition, memset the sinfo
buffer to zero before use on all paths in the current tree to avoid
leaving uninitialized pointers in the data.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 11 Aug 2011 01:00:33 +0000 (19:00 -0600)]
cfg80211: fix a crash in nl80211_send_station
mac80211 leaves sinfo->assoc_req_ies uninitialized, causing a random
pointer memory access in nl80211_send_station.
Instead of checking if the pointer is null, use sinfo->filled, like
the rest of the fields.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Mon, 8 Aug 2011 23:30:50 +0000 (16:30 -0700)]
mac80211: fix erroneous clearing of MESH_PATH_SN_VALID flag
When a PREQ or PREP is received from an intermediate node, it contains
useful information for path selection but it doesn't include the
originator's sequence number. Therefore, when updating the mesh path
to that intermediate node, we should not set the MESH_PATH_SN_VALID
flag. BUT, if the flag is set, it should not be unset as we might have
received a valid sequence number for that intermediate node in the past.
This issue was reported, fixed and tested by Ya Bo (游波) and Pedro
Larbig (ASPj).
Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Mon, 8 Aug 2011 13:50:22 +0000 (16:50 +0300)]
mac80211: clear sta.drv_priv on reconfiguration
drivers might assume sta.drv_priv is clear while
the sta is added, so clear it on reconfinguration.
Signed-off-by: Eliad Peller <eliad@wizery.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Mon, 8 Aug 2011 09:11:52 +0000 (12:11 +0300)]
cfg80211/nl80211: Send AssocReq IEs to user space in AP mode
When user space SME/MLME (e.g., hostapd) is not used in AP mode, the
IEs from the (Re)Association Request frame that was processed in
firmware need to be made available for user space (e.g., RSN IE for
hostapd). Allow this to be done with cfg80211_new_sta().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Mon, 8 Aug 2011 09:10:30 +0000 (12:10 +0300)]
nl80211: Indicate driver-based offchannel TX on mgmt_tx_cancel_wait
Drivers that support frame transmission with mgmt_tx() may not support
driver-based offchannel TX. Use mgmt_tx_cancel_wait instead of mgmt_tx
when figuring out whether to indicate support for this with
NL80211_ATTR_OFFCHANNEL_TX_OK.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Sat, 6 Aug 2011 20:07:00 +0000 (23:07 +0300)]
mac80211_hwsim: Fix RX status reporting for HT
RX_FLAG_HT must be included when reporting MCS rates. Without
this, mac80211 ended up dropping any frame sent at MCS index 12
or higher and that resulted in oddly random looking errors in
mac80211_hwsim tests.
Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Wed, 10 Aug 2011 06:49:12 +0000 (09:49 +0300)]
ath6kl: fix function name conflicts with ath9k
Stephen reported that compilation fails if both ath6kl and ath9k are
compiled in:
drivers/net/wireless/ath/ath6kl/built-in.o: In function `htc_start':
(.opd+0x600): multiple definition of `htc_start'
drivers/net/wireless/ath/ath9k/built-in.o:(.opd+0x3e40): first defined here
drivers/net/wireless/ath/ath6kl/built-in.o: In function `.htc_stop':
(.text+0x7b40): multiple definition of `.htc_stop'
drivers/net/wireless/ath/ath9k/built-in.o:(.text+0x67b34): first defined he=
re
drivers/net/wireless/ath/ath6kl/built-in.o: In function `.htc_start':
(.text+0x7d18): multiple definition of `.htc_start'
drivers/net/wireless/ath/ath9k/built-in.o:(.text+0x67ba0): first defined he=
re
drivers/net/wireless/ath/ath6kl/built-in.o: In function `htc_stop':
(.opd+0x5e8): multiple definition of `htc_stop'
drivers/net/wireless/ath/ath9k/built-in.o:(.opd+0x3e28): first defined here
To fix this add ath6kl prefix to all public functions in htc.c.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Larry Finger [Sat, 30 Jul 2011 16:30:27 +0000 (11:30 -0500)]
b43: Remove EXPERIMENTAL designation from LP PHY selection
Since kernel 3.0, the problems with controlling b43 devices that have
low-power (LP) PHYs have been fixed and the EXPERIMENTAL designation
can be fixed.
This patch also fixes a typo as the device supports 802.11b communications.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Acked-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 6 Aug 2011 11:13:48 +0000 (13:13 +0200)]
rt2x00: Fix PCI interrupt processing race on SMP systems
When toggle_irq is called for PCI devices to disable device interrupts
it used tasklet_disable to wait for a possibly running tasklet to finish.
However, on SMP systems the tasklet might still be scheduled on another CPU.
Instead, use tasklet_kill to ensure that all scheduled tasklets are finished
before returning from toggle_irq.
Furthermore, it was possible that a tasklet reenabled its interrupt even
though interrupts have been disabled already. Fix this by checking the
DEVICE_STATE_ENABLED_RADIO flag before reenabling single interrupts
during tasklet processing.
While at it also enable/kill the TBTT and PRETBTT tasklets in the
toggle_irq callback and only use tasklet_kill in stop_queue to wait
for a currently scheduled beacon update before returning.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sat, 6 Aug 2011 10:55:18 +0000 (05:55 -0500)]
rtlwifi: Eliminate raw reads and writes from PCIe portion
The PCIe driver used raw reads and writes on the PCIe hardware.
As all of these are only affecting the configuration space, all of
then can be converted to pci_{read,write}_config_XX calls.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: Use atomic reference count for interrupt ops
Let us enable/disable interrupts based on reference count.
By doing this we can ensure that interrupts are never be
enabled in the middle of tasklet processing. Instead of
addressing corner cases like "ath9k: avoid enabling interrupts
while processing rx", this approach handles it in generic manner.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Spur frequency was incorrectly computed with 10Mhz offset
which could cause the filter would not notch out the spur
and also this could improve rx sensitivity in HT40.
Cc: Madhan Jaganathan <madhanj@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: do not enable interrupt on set interrupt mask
At preset set_interrupt also enables interrupt after changing
mask. This is not necessary in all cases and also sometime it
breaks the assumption that interrupt was disabled. So let us
enable the interrupt explicity if it was disabled earlier.
This could also avoid unnecessary register ops and also helps
the follow up patch to have global ref count for interrupts ops.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / karo-tx-linux.git / log