Ulf Hansson [Mon, 8 Dec 2014 14:26:13 +0000 (15:26 +0100)]
mmc: pwrseq: Document DT bindings for the simple MMC power sequence
To support SOCs which specifies specific MMC power sequences, document
some MMC DT bindings to be able to describe these hardwares.
Let's also document bindings for a simple MMC power sequence provider,
which purpose is to support a set of common properties between various
SOCs.
In this initial step, let's also document a top level description of
the MMC power sequence and describe the compatible string used for the
simple MMC power sequence provider.
The simple MMC power sequence provider will initially support a reset
GPIO. From several earlier posted patches, it's clear that such
hardware exists. Especially some WLAN chips which are attached to an
SDIO interface may use a GPIO reset.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Ulf Hansson [Fri, 28 Nov 2014 13:38:36 +0000 (14:38 +0100)]
mmc: core: Initial support for MMC power sequences
System on chip designs may specify a specific MMC power sequence. To
successfully detect an (e)MMC/SD/SDIO card, that power sequence must
be followed while initializing the card.
To be able to handle these SOC specific power sequences, let's add a
MMC power sequence interface. It provides the following functions to
help the mmc core to deal with these power sequences.
mmc_pwrseq_alloc() - Invoked from mmc_of_parse(), to initialize data.
mmc_pwrseq_pre_power_on()- Invoked in the beginning of mmc_power_up().
mmc_pwrseq_post_power_on()- Invoked at the end in mmc_power_up().
mmc_pwrseq_power_off()- Invoked from mmc_power_off().
mmc_pwrseq_free() - Invoked from mmc_free_host(), to free data.
Each MMC power sequence provider will be responsible to implement a set
of callbacks. These callbacks mirrors the functions above.
This patch adds the skeleton, following patches will extend the core of
the MMC power sequence and add support for a specific simple MMC power
sequence.
Do note, since the mmc_pwrseq_alloc() is invoked from mmc_of_parse(),
host drivers needs to make use of this API to enable the support for
MMC power sequences. Moreover the MMC power sequence support depends on
CONFIG_OF.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Jisheng Zhang [Mon, 5 Jan 2015 07:59:19 +0000 (15:59 +0800)]
mmc: sdhci-pxav3: Remove checks for optional core clock in error/remove path
Commit 63589e92c2d9 ("clk: Ignore error and NULL pointers passed to
clk_{unprepare, disable}()") allows NULL or error pointer to be passed
unconditionally.
This patch is to simplify probe error and remove code paths.
However, we reserve the core clock checks in runtime suspend/resume code
because we want a little smaller latency.
Asaf Vertz [Tue, 20 Jan 2015 16:33:35 +0000 (18:33 +0200)]
mmc: block: fix format string warning
Fixed the following warning (reported by cppcheck):
[drivers/mmc/card/block.c:2149]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
mmc: tmio: enable SoC specific DMA buswidth settings
Renesas SDHI which is based on TMIO driver has 2 type SoC. 1st one is
used as SH-Mobile series, and 2nd is R-Car series. R-Car series SoC has
DMA buswidth setting register which enables 32bit access.
This patch adds .dma_buswidth and enables it.
Current tmio_mmc driver is using tmio_mmc_data for driver/platform
specific data/callback, and it is needed for tmio_mmc_host_probe()
function. Because of this style, include/linux/mfd/tmio.h header has
tmio driver/framework specific data which is not needed from platform.
This patch adds new tmio_mmc_host_alloc/free() as cleanup preparation.
tmio driver specific data/callback will be implemented in tmio_mmc_host,
and platform specific data/callback will be implemented in tmio_mmc_data
in this cleanup.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Vincent Yang [Tue, 20 Jan 2015 08:05:18 +0000 (16:05 +0800)]
mmc: sdhci: host: add new f_sdh30
This patch adds new host controller driver for
Fujitsu SDHCI controller f_sdh30.
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com> Signed-off-by: Andy Green <andy.green@linaro.org> Signed-off-by: Tetsuya Takinishi <t.takinishi@jp.fujitsu.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Vincent Yang [Tue, 20 Jan 2015 08:05:17 +0000 (16:05 +0800)]
mmc: sdhci: add a quirk for single block transactions
This patch defines a quirk to disable the block count
for single block transactions.
It is a preparation and will be used by Fujitsu
SDHCI controller f_sdh30 driver.
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Vincent Yang [Tue, 20 Jan 2015 08:05:16 +0000 (16:05 +0800)]
mmc: sdhci: add a quirk for tuning work around
This patch defines a quirk for tuning work
around for some sdhci host controller. It sets
both SDHCI_CTRL_EXEC_TUNING and SDHCI_CTRL_TUNED_CLK
for tuning.
It is a preparation and will be used by Fujitsu
SDHCI controller f_sdh30 driver.
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Vincent Yang [Tue, 20 Jan 2015 08:05:15 +0000 (16:05 +0800)]
mmc: sdhci: add a voltage switch callback function
This patch adds a callback function to do
controller-specific actions when switching voltages.
It is a preparation and will be used by Fujitsu
SDHCI controller f_sdh30 driver.
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Doug Anderson [Tue, 13 Jan 2015 23:58:44 +0000 (15:58 -0800)]
mmc: dw_mmc: Power on vqmmc in MMC_POWER_ON, not MMC_POWER_UP
If we power up vqmmc in MMC_POWER_ON then we end up turning it on
before mmc_power_up() sets the signal voltage. That's not so great
since we might be powering it up at the wrong voltage.
Note that this is how Yuvaraj originally coded things up in
<https://patchwork.kernel.org/patch/4401231/> but he changed it on my
suggestion. Apparently I was wrong.
Reported-by: Alexandru M Stan <amstan@chromium.org> Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jisheng Zhang [Sun, 4 Jan 2015 15:15:47 +0000 (23:15 +0800)]
mmc: sdhci-pxav3: fix unbalanced clock issues during probe
Commit 0dcaa2499b7d ("sdhci-pxav3: Fix runtime PM initialization") tries
to fix one hang issue caused by calling sdhci_add_host() on a suspended
device. The fix enables the clock twice, once by clk_prepare_enable() and
another by pm_runtime_get_sync(), meaning that the clock will never be
gated at runtime PM suspend. I observed the power consumption regression on
Marvell BG2Q SoCs.
In fact, the fix is not correct. There still be a very small window
during which a runtime suspend might somehow occur after pm_runtime_enable()
but before pm_runtime_get_sync().
This patch fixes all of the two problems by just incrementing the usage
counter before pm_runtime_enable(). It also adjust the order of disabling
runtime pm and storing the usage count in the error path to handle clock
gating properly.
Adrian Hunter [Fri, 5 Dec 2014 17:41:10 +0000 (19:41 +0200)]
mmc: sdhci: Always init buf_ready_int
There is no point making the initialization
of buf_ready_int conditional on host version.
Simplify by just doing it always. Note that
the other conditional initializations will be
removed when the new way of doing re-tuning
is taken into use.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Fri, 5 Dec 2014 17:40:59 +0000 (19:40 +0200)]
mmc: core: Simplify by adding mmc_execute_tuning()
For each MMC, SD and SDIO there is code that
holds the clock, calls ops->execute_tuning, and
releases the clock. Simplify the code a bit by
providing a separate function to do that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
NeilBrown [Mon, 12 Jan 2015 19:23:18 +0000 (08:23 +1300)]
mmc: slot-gpio: Allow host driver to provide isr for card-detect interrupts
One of the reasons omap_hsmmc doesn't use the slot-gpio library
is that it has some non-standard functionality in the card-detect
interrupt service routine.
To make it possible for omap_hsmmc (and maybe others) to be converted
to use slot-gpio, add 'mmc_gpio_request_cd_isr' which provide an
alternate isr to be register by the slot-gpio code.
Johan Rudholm [Mon, 12 Jan 2015 14:38:05 +0000 (15:38 +0100)]
mmc: core: refactor the hw_reset routines
Move the (e)MMC specific hw_reset code from core.c into mmc.c. Call the
code from the new bus_ops member "reset". This also allows for adding
a SD card specific reset procedure.
Signed-off-by: Johan Rudholm <johanru@axis.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Johan Rudholm [Mon, 12 Jan 2015 14:38:04 +0000 (15:38 +0100)]
mmc: core: always check status after reset
Always check if the card is alive after a successful reset. This allows
us to remove mmc_hw_reset_check(), leaving mmc_hw_reset() as the only
card reset interface.
Signed-off-by: Johan Rudholm <johanru@axis.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sascha Hauer [Mon, 30 Jun 2014 09:07:25 +0000 (11:07 +0200)]
mmc: Add SDIO function devicetree subnode parsing
This adds SDIO devicetree subnode parsing to the mmc core. While
SDIO devices are runtime probable they sometimes need nonprobable
additional information on embedded systems, like an additional gpio
interrupt or a clock. This patch makes it possible to supply this
information from the devicetree. SDIO drivers will find a pointer
to the devicenode in their devices of_node pointer.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[hdegoede@redhat.com: Misc. cleanups] Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sascha Hauer [Mon, 30 Jun 2014 09:07:24 +0000 (11:07 +0200)]
mmc: Add SDIO function subnode DT documentation
While SDIO devices are runtime probable they sometimes need nonprobable
additional information on embedded systems, like an additional gpio
interrupt or a clock. This binding describes how to add child nodes to the
devicetree to supply this information.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[hdegoede@redhat.com: Documented the need for #address- and #size-cells]
[hdegoede@redhat.com: Added a real world example] Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bounce buffer, used for misaligned bytes for ADMA access,
resides wholly within the (align_sz)-aligned word, just by construction.
The page addresses are aligned to (align_sz), either for 4 or 8 bytes
alignment, so that the aligned word resides wholly within a single page
and can't cross the page boundary. So, the bounce buffer can't cross
the page boundary too. That's why the warnings are never hit, and can
be safely removed.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Mon, 1 Dec 2014 15:13:39 +0000 (16:13 +0100)]
mmc: dw_mmc: Convert to mmc_send_tuning()
Instead of having a local hack taking care of sending the tuning
command and as well to verify the response pattern, let's convert to
the common mmc_send_tuning() API.
This change affects the Exynos variant, since it's the only one which
support the dw_mmc's ->execute_tuning() callback.
It's seems like dw_mmc internal logic expects failed data transfers to
be ended using a stop command. Let the tuning requests also fall into
this category, since there are data transfer involved.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Ulf Hansson [Thu, 11 Dec 2014 14:12:25 +0000 (15:12 +0100)]
mmc: sdhci-esdhc-imx: Fixup runtime PM conditions during ->probe()
By configure runtime PM prior we enable the use of it, we close the gap
for strange and unhandled conditions. Moreover it makes us rely on the
driver core, after finalized ->probe(), to request an inactive device
to become runtime PM idle/suspended, which earlier potentially could
happen already at pm_runtime_set_autosuspend_delay().
Ulf Hansson [Thu, 11 Dec 2014 13:56:15 +0000 (14:56 +0100)]
mmc: sdhci-esdhc-imx: Fixup ->remove()
Since sdhci_remove_host() access the device, we need to make sure it's
runtime PM resumed.
To handle clock gating properly in remove, we first have to make sure
the clocks are ungated.
To fix both these issues, by invoking pm_runtime_get_sync() early in
->remove() callback. Later once we disabled runtime PM, we can restore
the usage count.
Micky Ching [Tue, 23 Dec 2014 01:19:45 +0000 (09:19 +0800)]
mmc: rtsx: add support for sdio card
Modify transfer mode for support sdio card,
send cmd and data at the same time for read data transfer,
but send data after cmd for write data transfer.
Micky Ching [Tue, 23 Dec 2014 01:19:44 +0000 (09:19 +0800)]
mmc: rtsx: add helper function to simplify code
To support sdio card, transfer mode need make a change,
this need to split code and use it in different place,
Add new function to simplify repeat operation.
Micky Ching [Tue, 23 Dec 2014 01:19:42 +0000 (09:19 +0800)]
mmc: rtsx: add dump_reg_range to simplify dump register
Add a new function to dump register within a range.
We print 1 register a line before this patch,
this may make debug info too long when we add more register to dump.
The new dump_reg_range() dump to 8 register a line,
and it is easy to use.
Ulf Hansson [Thu, 18 Dec 2014 14:44:34 +0000 (15:44 +0100)]
mmc: slot-gpio: Make mmc_gpio_alloc() available for MMC core
As a step in moving slot-gpio functions/structs closer to the MMC core,
let's add a local header file for slot-gpio.
In this initial step we move mmc_gpio_alloc() into the header file,
to make it available for the MMC core. Following patches will show the
utilization of it.
Ulf Hansson [Thu, 18 Dec 2014 14:44:32 +0000 (15:44 +0100)]
mmc: slot-gpio: Remove option to explicitly free requested CD/WP GPIOs
The slot-gpio uses the devm*_ managed functions. Still it provide APIs
to explicitly free requested CD/WP GPIOs, but these API isn't being
used.
Therefore let's simplify slot-gpio by removing these unused APIs. If it
later turns out we need some of them, we can always consider to restore
the code.
Ulf Hansson [Thu, 18 Dec 2014 09:41:44 +0000 (10:41 +0100)]
mmc: core: Return error at failure of request CD/WP in mmc_of_parse()
Instead of just printing an error when mmc_of_parse() fails to request
CD/WP GPIO pins, let's propagate all errors, except for -ENOENT.
Earlier only -EPROBE_DEFER was handled correctly.
As a side effect of this change and by relying on host drivers to
handle the errors during ->probe(), we don't need to free any data in
the error path.
This also means we are actually fixing a bug, since we remove the call
to mmc_gpio_free_cd() which wasn't the correct function to invoke to
handle cleanup. Instead that should have been mmc_gpiod_free_cd().
Seungwon Jeon [Mon, 22 Dec 2014 12:12:02 +0000 (17:42 +0530)]
mmc: dw_mmc: fix the max_blk_count in IDMAC
Even though 1MB is reserved for descriptor table in IDMAC,
the dw_mmc host driver is allowed to receive only maximum
128KB block length in one request. This is caused by setting
improper max_blk_count. It needs to be e adjusted so that
descriptor table is used fully. It is found that the performance
is improved with the increased the max_blk_count.
Removing a relict from reverse engineering of the Android driver code
in sunxi_mmc_clk_set_rate.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch> Reported-by: <lixiang@allwinnertech.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixing the register name in sunxi_mmc_reset_host since the
SDXC_HARDWARE_RESET bit is actually located within REG_GCTRL and not
REG_CMDR as it was pointed out by Allwinner.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch> Reported-by: <lixiang@allwinnertech.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
1) Adding a comment in order to clarify the choice of the locks within
sunxi_mmc_handle_manual_stop
2) As <lixiang@allwinnertech.com> has pointed out the wait_dma variable
was not accessed within the spin lock block in sunxi_mmc_request and so
(even if it should never happend) it would have theoretically been
possible that some other function would access the variable at the same
time as the function. This has been changed now and the function is
using local variables outside the lock and copys the value over during
the lock phase.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch> Reported-by: <lixiang@allwinnertech.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hans de Goede [Tue, 16 Dec 2014 14:10:59 +0000 (15:10 +0100)]
mmc: sunxi: Fix setup of last descriptor of dma transfer
The last descriptor might be the first descriptor as well, so use masking to
add the LD (last descriptor) bit and drop the DIC (disable interrupt on
completion) bit rather then hard assignment as hard assignment will override
the FD (first descriptor) bit if there is only 1 descriptor.
Also set the ER (end of ring) bit and clear buf_addr_ptr2 on the last
descriptor, like the android kernel code does.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch> Reported-by: <lixiang@allwinnertech.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
justified it by the need to avoid the registration of new devices
during suspend.
However mmc_pm_notify will set ->rescan_disable in the 'prepare'
stage and clear it in the 'complete' stage, so no card detection
will actually happen.
Also the interrupt will be disabled before final suspend as part
of common suspend processing.
So this disabling of the interrupt is unnecessary, and interferes
with a transition to using common code for card-detect management.
Cc: Felipe Balbi <balbi@ti.com> Cc: Venkatraman S <svenkatr@ti.com> Cc: Chris Ball <cjb@laptop.org> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 0718e59ae259 ("mmc: sdhci: move FSL ESDHC reset handling quirk into
esdhc code") states that Freescale esdhc is the only controller which needs
the interrupt registers restored after a reset. So it moves
SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET quirk handling code into the
esdhc-imx driver only. Unfortunately the same controller is used in
other boards which use the of-esdhc driver instead (like powerpc P2020).
Restore interrupts after reset in the sdhci-of-esdhc driver also.
Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Minda Chen [Thu, 4 Dec 2014 12:09:20 +0000 (20:09 +0800)]
mmc: sdhci-sirf: add sirf tuning function (cmd 19)
Add manual tuning function in CSR atlas7 SoC. It is mainly used
for the UHS-I SD card working SDR50 SDR104 mode.
The tuning principle can be seen in SD spec part1 v3.01 4.2.4.5
(tuning command).
SD host send the cmd19 and set the delay value(0-127).
and the sdcard return 64 bytes data. If the data is same with
the tuning data. The delay value is valid. Execute this commmand
128 times. And calculate the longest window of the valid values.
The value in the middle of this window is the best value.
Signed-off-by: Minda Chen <Minda.Chen@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
...actually triggers the error message. That's because the
dw_mci_enable_sdio_irq() unsafely does a read-modify-write of the
INTMASK register.
We can't just use the standard host->lock since that lock is not irq
safe and mmc_signal_sdio_irq() (called from interrupt context) calls
dw_mci_enable_sdio_irq(). Add a new irq-safe lock to protect INTMASK.
An alternate solution to this is to punt mmc_signal_sdio_irq() to the
tasklet and then protect INTMASK modifications by the standard host
lock. This seemed like a bit more of a high-latency change.
Reported-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Doug Anderson <dianders@chromium.org> Reviewed-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Doug Anderson [Tue, 2 Dec 2014 23:42:46 +0000 (15:42 -0800)]
mmc: dw_mmc: Cleanup disable of low power mode w/ SDIO interrupts
In the patch (9623b5b mmc: dw_mmc: Disable low power mode if SDIO
interrupts are used) I added code that disabled the low power mode of
dw_mmc when SDIO interrupts are used. That code worked but always
felt a little hacky because we ended up disabling low power as a side
effect of the first enable_sdio_irq() call. That wouldn't be so bad
except that disabling low power involves a complicated process of
writing to the CMD/CMDARG registers and that extra process makes it
difficult to cleanly the read-modify-write race in
dw_mci_enable_sdio_irq() (see future patch in the series).
Change the code to take advantage of the init_card() callback of the
mmc core to do this right at bootup.
Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Doug Anderson [Tue, 2 Dec 2014 23:42:45 +0000 (15:42 -0800)]
mmc: core: Support the optional init_card() callback for MMC and SD
In (3fcb027 ARM: MXC: mxcmmc: work around a bug in the SDHC busy line
handling) the optional init_card() callback was added. According to
the original change it was "for now only called from
mmc_sdio_init_card()".
This callback really ought to be called from the SD and MMC init
functions as well. One current user of this callback
(mxcmci_init_card) will not work as expected if you insert an SDIO
card, then eject it and put a normal SD card in. Specifically the
normal SD card will not get to run with 4-bit data.
I'd like to use the init_card() callback to handle a similar quirk on
dw_mmc when using SDIO Interrupts (the "low power" feature of the card
needs to be disabled), so that will add a second user of the function.
Signed-off-by: Doug Anderson <dianders@chromium.org> Reviewed-by: Grant Grundler <grundler@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Doug Anderson [Tue, 2 Dec 2014 23:42:44 +0000 (15:42 -0800)]
ARM: OMAP2+: Make sure pandora_wl1251_init_card() applies to SDIO only
In preparation for having init_card() called for all card types (not
just SDIO), change pandora_wl1251_init_card() so it checks whether the
card type is SDIO.
Signed-off-by: Doug Anderson <dianders@chromium.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Linus Torvalds [Sun, 18 Jan 2015 06:00:40 +0000 (18:00 +1200)]
Merge tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We've been sitting on our fixes branch for a while, so this batch is
unfortunately on the large side.
A lot of these are tweaks and fixes to device trees, fixing various
bugs around clocks, reg ranges, etc. There's also a few defconfig
updates (which are on the late side, no more of those).
All in all the diffstat is bigger than ideal at this time, but nothing
in here seems particularly risky"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
reset: sunxi: fix spinlock initialization
ARM: dts: disable CCI on exynos5420 based arndale-octa
drivers: bus: check cci device tree node status
ARM: rockchip: disable jtag/sdmmc autoswitching on rk3288
ARM: nomadik: fix up leftover device tree pins
ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree
ARM: at91/dt: sam9263: Add missing clocks to lcdc node
ARM: at91: sama5d3: dt: correct the sound route
ARM: at91/dt: sama5d4: fix the timer reg length
ARM: exynos_defconfig: Enable LM90 driver
ARM: exynos_defconfig: Enable options for display panel support
arm: dts: Use pmu_system_controller phandle for dp phy
ARM: shmobile: sh73a0 legacy: Set .control_parent for all irqpin instances
ARM: dts: berlin: correct BG2Q's SM GPIO location.
ARM: dts: berlin: add broken-cd and set bus width for eMMC in Marvell DMP DT
ARM: dts: berlin: fix io clk and add missing core clk for BG2Q sdhci2 host
ARM: dts: Revert disabling of smc91x for n900
ARM: dts: imx51-babbage: Fix ULPI PHY reset modelling
ARM: dts: dra7-evm: fix qspi device tree partition size
ARM: omap2plus_defconfig: use CONFIG_CPUFREQ_DT
...
Linus Torvalds [Sun, 18 Jan 2015 03:29:11 +0000 (15:29 +1200)]
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux
Pull clock driver fixes from Mike Turquette:
"Small number of fixes for clock drivers and a single null pointer
dereference fix in the framework core code.
The driver fixes vary from fixing section mismatch warnings to
preventing machines from hanging (and preventing developers from
crying)"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: fix possible null pointer dereference
Revert "clk: ppc-corenet: Fix Section mismatch warning"
clk: rockchip: fix deadlock possibility in cpuclk
clk: berlin: bg2q: remove non-exist "smemc" gate clock
clk: at91: keep slow clk enabled to prevent system hang
clk: rockchip: fix rk3288 cpuclk core dividers
clk: rockchip: fix rk3066 pll lock bit location
clk: rockchip: Fix clock gate for rk3188 hclk_emem_peri
clk: rockchip: add CLK_IGNORE_UNUSED flag to fix rk3066/rk3188 USB Host
Linus Torvalds [Sun, 18 Jan 2015 03:26:52 +0000 (15:26 +1200)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is one fix for a Multiqueue sleeping in invalid context problem
and a MAINTAINER file update for Qlogic"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ->queue_rq can't sleep
MAINTAINERS: Update maintainer list for qla4xxx
The commit 646cafc6 (clk: Change clk_ops->determine_rate to
return a clk_hw as the best parent) opens a possibility for
null pointer dereference, fix this.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com> Reviewed-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Michael Turquette <mturquette@linaro.org>
That commit tried to fix the section mismatch warning by moving the
ppc_corenet_clk_driver struct to init section. This is definitely wrong
because the kernel would free the memories occupied by this struct
after boot while this driver is still registered in the driver core.
The kernel would panic when accessing this driver struct.
Cc: stable@vger.kernel.org # 3.17 Signed-off-by: Kevin Hao <haokexin@gmail.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Michael Turquette <mturquette@linaro.org>
Linus Torvalds [Sat, 17 Jan 2015 18:26:24 +0000 (06:26 +1200)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Two patches, the first by Andy to fix dw dmac runtime pm and second
one by me to fix the dmaengine headers in MAINTAINERS"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: dw: balance PM runtime calls
MAINTAINERS: dmaengine: fix the header file for dmaengine
projects / linux-beck.git / log