David S. Miller [Sat, 26 Nov 2016 01:21:24 +0000 (20:21 -0500)]
Merge branch 'thunderx-new-features'
Sunil Goutham says:
====================
net: thunderx: Support for 80xx, RED, PFC e.t.c
This patch series adds support for SLM modules present on 80xx
silicon, enables ramdom early discard, backpressure generation,
PFC and some ethtool changes to display supported link modes e.t.c.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Thu, 24 Nov 2016 09:18:03 +0000 (14:48 +0530)]
net: thunderx: Pause frame support
Enable pause frames on both Rx and Tx side, configure pause
interval e.t.c. Also support for enable/disable pause frames
on Rx/Tx via ethtool has been added.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Thu, 24 Nov 2016 09:18:02 +0000 (14:48 +0530)]
net: thunderx: Configure RED and backpressure levels
This patch enables moving average calculation of Rx pkt's resources
and configures RED and backpressure levels for both CQ and RBDR.
Also initialize SQ's CQ_LIMIT properly.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: thunderx: Add ethtool support for supported ports and link modes.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@cavium.com> Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Thu, 24 Nov 2016 09:18:00 +0000 (14:48 +0530)]
net: thunderx: 80xx BGX0 configuration changes
On 80xx only one lane of DLM0 and DLM1 (of BGX0) can be used
, so even though lmac count may be 2 but LMAC1 should use
serdes lane of DLM1. Since it's not possible to distinguish
80xx from 81xx as PCI devid are same, this patch adds this
config support by replying on what firmware configures the
lmacs with.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Woojung Huh [Wed, 23 Nov 2016 23:10:33 +0000 (23:10 +0000)]
phy: fix error case of phy_led_triggers_(un)register
When phy_init_hw() fails at phy_attach_direct();
- phy_detach() calls phy_led_triggers_unregister() without
previous call of phy_led_triggers_register().
- still call phy_led_triggers_register() and cause memory leak.
Fixes: 2e0bc452f472 ("net: phy: leds: add support for led triggers on phy link state change") Signed-off-by: Woojung Huh <woojung.huh@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 23 Nov 2016 16:44:56 +0000 (08:44 -0800)]
net: properly flush delay-freed skbs
Typical NAPI drivers use napi_consume_skb(skb) at TX completion time.
This put skb in a percpu special queue, napi_alloc_cache, to get bulk
frees.
It turns out the queue is not flushed and hits the NAPI_SKB_CACHE_SIZE
limit quite often, with skbs that were queued hundreds of usec earlier.
I measured this can take ~6000 nsec to perform one flush.
__kfree_skb_flush() can be called from two points right now :
1) From net_tx_action(), but only for skbs that were queued to
sd->completion_queue.
-> Irrelevant for NAPI drivers in normal operation.
2) From net_rx_action(), but only under high stress or if RPS/RFS has a
pending action.
This patch changes net_rx_action() to perform the flush in all cases and
after more urgent operations happened (like kicking remote CPUS for
RPS/RFS).
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jesper Dangaard Brouer <brouer@redhat.com> Cc: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 25 Nov 2016 21:26:12 +0000 (16:26 -0500)]
Merge branch 'cgroup-bpf'
Daniel Mack says:
====================
Add eBPF hooks for cgroups
This is v9 of the patch set to allow eBPF programs for network
filtering and accounting to be attached to cgroups, so that they apply
to all sockets of all tasks placed in that cgroup. The logic also
allows to be extendeded for other cgroup based eBPF logic.
Again, only minor details are updated in this version.
Changes from v8:
* Move the egress hooks into ip_finish_output() and ip6_finish_output()
so they run after the netfilter hooks. For IPv4 multicast, add a new
ip_mc_finish_output() callback that is invoked on success by
netfilter, and call the eBPF program from there.
Changes from v7:
* Replace the static inline function cgroup_bpf_run_filter() with
two specific macros for ingress and egress. This addresses David
Miller's concern regarding skb->sk vs. sk in the egress path.
Thanks a lot to Daniel Borkmann and Alexei Starovoitov for the
suggestions.
Changes from v6:
* Rebased to 4.9-rc2
* Add EXPORT_SYMBOL(__cgroup_bpf_run_filter). The kbuild test robot
now succeeds in building this version of the patch set.
* Switch from bpf_prog_run_save_cb() to bpf_prog_run_clear_cb() to not
tamper with the contents of skb->cb[]. Pointed out by Daniel
Borkmann.
* Use sk_to_full_sk() in the egress path, as suggested by Daniel
Borkmann.
* Renamed BPF_PROG_TYPE_CGROUP_SOCKET to BPF_PROG_TYPE_CGROUP_SKB, as
requested by David Ahern.
* Added Alexei's Acked-by tags.
Changes from v5:
* The eBPF programs now operate on L3 rather than on L2 of the packets,
and the egress hooks were moved from __dev_queue_xmit() to
ip*_output().
* For BPF_PROG_TYPE_CGROUP_SOCKET, disallow direct access to the skb
through BPF_LD_[ABS|IND] instructions, but hook up the
bpf_skb_load_bytes() access helper instead. Thanks to Daniel Borkmann
for the help.
Changes from v4:
* Plug an skb leak when dropping packets due to eBPF verdicts in
__dev_queue_xmit(). Spotted by Daniel Borkmann.
* Check for sk_fullsock(sk) in __cgroup_bpf_run_filter() so we don't
operate on timewait or request sockets. Suggested by Daniel Borkmann.
* Add missing @parent parameter in kerneldoc of __cgroup_bpf_update().
Spotted by Rami Rosen.
* Include linux/jump_label.h from bpf-cgroup.h to fix a kbuild error.
Changes from v3:
* Dropped the _FILTER suffix from BPF_PROG_TYPE_CGROUP_SOCKET_FILTER,
renamed BPF_ATTACH_TYPE_CGROUP_INET_{E,IN}GRESS to
BPF_CGROUP_INET_{IN,E}GRESS and alias BPF_MAX_ATTACH_TYPE to
__BPF_MAX_ATTACH_TYPE, as suggested by Daniel Borkmann.
* Dropped the attach_flags member from the anonymous struct for BPF
attach operations in union bpf_attr. They can be added later on via
CHECK_ATTR. Requested by Daniel Borkmann and Alexei.
* Release old_prog at the end of __cgroup_bpf_update rather that at
the beginning to fix a race gap between program updates and their
users. Spotted by Daniel Borkmann.
* Plugged an skb leak when dropping packets on the egress path.
Spotted by Daniel Borkmann.
* Add cgroups@vger.kernel.org to the loop, as suggested by Rami Rosen.
* Some minor coding style adoptions not worth mentioning in particular.
Changes from v2:
* Fixed the RCU locking details Tejun pointed out.
* Assert bpf_attr.flags == 0 in BPF_PROG_DETACH syscall handler.
Changes from v1:
* Moved all bpf specific cgroup code into its own file, and stub
out related functions for !CONFIG_CGROUP_BPF as static inline nops.
This way, the call sites are not cluttered with #ifdef guards while
the feature remains compile-time configurable.
* Implemented the new scheme proposed by Tejun. Per cgroup, store one
set of pointers that are pinned to the cgroup, and one for the
programs that are effective. When a program is attached or detached,
the change is propagated to all the cgroup's descendants. If a
subcgroup has its own pinned program, skip the whole subbranch in
order to allow delegation models.
* The hookup for egress packets is now done from __dev_queue_xmit().
* A static key is now used in both the ingress and egress fast paths
to keep performance penalties close to zero if the feature is
not in use.
* Overall cleanup to make the accessors use the program arrays.
This should make it much easier to add new program types, which
will then automatically follow the pinned vs. effective logic.
* Fixed locking issues, as pointed out by Eric Dumazet and Alexei
Starovoitov. Changes to the program array are now done with
xchg() and are protected by cgroup_mutex.
* eBPF programs are now expected to return 1 to let the packet pass,
not >= 0. Pointed out by Alexei.
* Operation is now limited to INET sockets, so local AF_UNIX sockets
are not affected. The enum members are renamed accordingly. In case
other socket families should be supported, this can be extended in
the future.
* The sample program learned to support both ingress and egress, and
can now optionally make the eBPF program drop packets by making it
return 0.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Mack [Wed, 23 Nov 2016 15:52:30 +0000 (16:52 +0100)]
samples: bpf: add userspace example for attaching eBPF programs to cgroups
Add a simple userpace program to demonstrate the new API to attach eBPF
programs to cgroups. This is what it does:
* Create arraymap in kernel with 4 byte keys and 8 byte values
* Load eBPF program
The eBPF program accesses the map passed in to store two pieces of
information. The number of invocations of the program, which maps
to the number of packets received, is stored to key 0. Key 1 is
incremented on each iteration by the number of bytes stored in
the skb.
* Detach any eBPF program previously attached to the cgroup
* Attach the new program to the cgroup using BPF_PROG_ATTACH
* Once a second, read map[0] and map[1] to see how many bytes and
packets were seen on any socket of tasks in the given cgroup.
The program takes a cgroup path as 1st argument, and either "ingress"
or "egress" as 2nd. Optionally, "drop" can be passed as 3rd argument,
which will make the generated eBPF program return 0 instead of 1, so
the kernel will drop the packet.
libbpf gained two new wrappers for the new syscall commands.
Signed-off-by: Daniel Mack <daniel@zonque.org> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Mack [Wed, 23 Nov 2016 15:52:29 +0000 (16:52 +0100)]
net: ipv4, ipv6: run cgroup eBPF egress programs
If the cgroup associated with the receiving socket has an eBPF
programs installed, run them from ip_output(), ip6_output() and
ip_mc_output(). From mentioned functions we have two socket contexts
as per 7026b1ddb6b8 ("netfilter: Pass socket pointer down through
okfn()."). We explicitly need to use sk instead of skb->sk here,
since otherwise the same program would run multiple times on egress
when encap devices are involved, which is not desired in our case.
eBPF programs used in this context are expected to either return 1 to
let the packet pass, or != 1 to drop them. The programs have access to
the skb through bpf_skb_load_bytes(), and the payload starts at the
network headers (L3).
Note that cgroup_bpf_run_filter() is stubbed out as static inline nop
for !CONFIG_CGROUP_BPF, and is otherwise guarded by a static key if
the feature is unused.
Signed-off-by: Daniel Mack <daniel@zonque.org> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Mack [Wed, 23 Nov 2016 15:52:28 +0000 (16:52 +0100)]
net: filter: run cgroup eBPF ingress programs
If the cgroup associated with the receiving socket has an eBPF
programs installed, run them from sk_filter_trim_cap().
eBPF programs used in this context are expected to either return 1 to
let the packet pass, or != 1 to drop them. The programs have access to
the skb through bpf_skb_load_bytes(), and the payload starts at the
network headers (L3).
Note that cgroup_bpf_run_filter() is stubbed out as static inline nop
for !CONFIG_CGROUP_BPF, and is otherwise guarded by a static key if
the feature is unused.
Signed-off-by: Daniel Mack <daniel@zonque.org> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Mack [Wed, 23 Nov 2016 15:52:27 +0000 (16:52 +0100)]
bpf: add BPF_PROG_ATTACH and BPF_PROG_DETACH commands
Extend the bpf(2) syscall by two new commands, BPF_PROG_ATTACH and
BPF_PROG_DETACH which allow attaching and detaching eBPF programs
to a target.
On the API level, the target could be anything that has an fd in
userspace, hence the name of the field in union bpf_attr is called
'target_fd'.
When called with BPF_ATTACH_TYPE_CGROUP_INET_{E,IN}GRESS, the target is
expected to be a valid file descriptor of a cgroup v2 directory which
has the bpf controller enabled. These are the only use-cases
implemented by this patch at this point, but more can be added.
If a program of the given type already exists in the given cgroup,
the program is swapped automically, so userspace does not have to drop
an existing program first before installing a new one, which would
otherwise leave a gap in which no program is attached.
For more information on the propagation logic to subcgroups, please
refer to the bpf cgroup controller implementation.
The API is guarded by CAP_NET_ADMIN.
Signed-off-by: Daniel Mack <daniel@zonque.org> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Mack [Wed, 23 Nov 2016 15:52:26 +0000 (16:52 +0100)]
cgroup: add support for eBPF programs
This patch adds two sets of eBPF program pointers to struct cgroup.
One for such that are directly pinned to a cgroup, and one for such
that are effective for it.
To illustrate the logic behind that, assume the following example
cgroup hierarchy.
A - B - C
\ D - E
If only B has a program attached, it will be effective for B, C, D
and E. If D then attaches a program itself, that will be effective for
both D and E, and the program in B will only affect B and C. Only one
program of a given type is effective for a cgroup.
Attaching and detaching programs will be done through the bpf(2)
syscall. For now, ingress and egress inet socket filtering are the
only supported use-cases.
Signed-off-by: Daniel Mack <daniel@zonque.org> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Mack [Wed, 23 Nov 2016 15:52:25 +0000 (16:52 +0100)]
bpf: add new prog type for cgroup socket filtering
This program type is similar to BPF_PROG_TYPE_SOCKET_FILTER, except that
it does not allow BPF_LD_[ABS|IND] instructions and hooks up the
bpf_skb_load_bytes() helper.
Programs of this type will be attached to cgroups for network filtering
and accounting.
Signed-off-by: Daniel Mack <daniel@zonque.org> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Wed, 23 Nov 2016 11:02:44 +0000 (11:02 +0000)]
cxgb4: fix memory leak on txq_info
Currently if txq_info->uldtxq cannot be allocated then
txq_info->txq is being kfree'd (which is redundant because it
is NULL) instead of txq_info. Fix this by instead kfree'ing
txq_info.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 23 Nov 2016 02:26:49 +0000 (10:26 +0800)]
tuntap: remove unnecessary sk_receive_queue length check during xmit
After commit 1576d9860599 ("tun: switch to use skb array for tx"),
sk_receive_queue was not used any more. So remove the uncessary
sk_receive_queue length check during xmit.
Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
llvm can emit relocations into sections other than program code
(like debug info sections). Ignore them during parsing of elf file
Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
since llvm commit "Do not expand UNDEF SDNode during insn selection lowering"
llvm will generate code that uses uninitialized registers for cases
where C code is actually uses uninitialized data.
So this sockex2 example is technically broken.
Fix it by initializing on the stack variable fully.
Also increase verifier buffer limit, since verifier output
may not fit in 64k for this sockex2 code depending on llvm version.
Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
long unsigned int bytes; /* 0x48 0x8 */
long unsigned int packets; /* 0x50 0x8 */
long unsigned int tx_csum; /* 0x58 0x8 */
long unsigned int tso_packets; /* 0x60 0x8 */
long unsigned int xmit_more; /* 0x68 0x8 */
unsigned int tx_dropped; /* 0x70 0x4 */
Florian Fainelli [Tue, 22 Nov 2016 21:55:31 +0000 (13:55 -0800)]
ethtool: Protect {get, set}_phy_tunable with PHY device mutex
PHY drivers should be able to rely on the caller of {get,set}_tunable to
have acquired the PHY device mutex, in order to both serialize against
concurrent calls of these functions, but also against PHY state machine
changes. All ethtool PHY-level functions do this, except
{get,set}_tunable, so we make them consistent here as well.
We need to update the Microsemi PHY driver in the same commit to avoid
introducing either deadlocks, or lack of proper locking.
Fixes: 968ad9da7e0e ("ethtool: Implements ETHTOOL_PHY_GTUNABLE/ETHTOOL_PHY_STUNABLE") Fixes: 310d9ad57ae0 ("net: phy: Add downshift get/set support in Microsemi PHYs driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Allan W. Nielsen <allan.nielsen@microsemi.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This series from Roi and Or further enhances the new SRIOV switchdev mode.
Roi's patches deal with allowing users to configure though devlink
the level of inline headers that the VF should be setting in order for
the eswitch HW to do proper matching. We also enforce that the matching
required for offloaded TC rules is aligned with that level on the PF driver.
Or's patches deals with allowing the user to control on the VF operational
link state through admin directives on the mlx5 VF rep link. Also in this series
is implementation of HW and SW counters for the mlx5 VF rep which is aligned
with the design set by commit a5ea31f57309 'Merge branch net-offloaded-stats'.
v1 --> v2:
* constified the net-device param of get offloaded stats ndo in mlxsw
(pointed by 0-day screaming on us...)
* added Or's Review-by tags for Roi's patches
This series was generated against commit e796f49d826a ("net: ieee802154: constify ieee802154_ops structures")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Roi Dayan [Tue, 22 Nov 2016 21:10:00 +0000 (23:10 +0200)]
net/mlx5e: Enforce min inline mode when offloading flows
A flow should be offloaded only if the matches are
allowed according to min inline mode.
Signed-off-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roi Dayan [Tue, 22 Nov 2016 21:09:59 +0000 (23:09 +0200)]
net/mlx5: E-Switch, Add control for inline mode
Implement devlink show and set of HW inline-mode.
The supported modes: none, link, network, transport.
We currently support one mode for all vports so set is done on all vports.
When eswitch is first initialized the inline-mode is queried from the FW.
Signed-off-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roi Dayan [Tue, 22 Nov 2016 21:09:58 +0000 (23:09 +0200)]
net/mlx5: Enable to query min inline for a specific vport
Also move the inline capablities enum to a shared header vport.h
Signed-off-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roi Dayan [Tue, 22 Nov 2016 21:09:57 +0000 (23:09 +0200)]
devlink: Add E-Switch inline mode control
Some HWs need the VF driver to put part of the packet headers on the
TX descriptor so the e-switch can do proper matching and steering.
The supported modes: none, link, network, transport.
Signed-off-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Tue, 22 Nov 2016 21:09:56 +0000 (23:09 +0200)]
net/mlx5e: Support VF vport link state control for SRIOV switchdev mode
Reflect the administative link changes done on the VF representor to the
VF e-switch vport. This means that doing ip link set down/up commands on
the VF rep will modify the e-switch vport state which in turn will make
proper VF drivers to set their carrier accordingly.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Tue, 22 Nov 2016 21:09:55 +0000 (23:09 +0200)]
net/mlx5e: Support HW (offloaded) and SW counters for SRIOV switchdev mode
Switchdev driver net-device port statistics should follow the model introduced
in commit a5ea31f57309 'Merge branch net-offloaded-stats'.
For VF reps we return the SRIOV eswitch vport stats as the usual ones and SW stats
if asked. For the PF, if we're in the switchdev mode, we return the uplink stats
and SW stats if asked, otherwise as before. The uplink stats are implemented using
the PPCNT 802_3 counters which are already being read/cached by the driver.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Tue, 22 Nov 2016 21:09:54 +0000 (23:09 +0200)]
net: Add net-device param to the get offloaded stats ndo
Some drivers would need to check few internal matters for
that. To be used in downstream mlx5 commit.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: phy: broadcom: Wirespeed/downshift support
This patch series adds support for the Broadcom Wirespeed, aka
downsfhit feature utilizing the recently added ethtool PHY tunables.
Tested with two Gigabit link partners with a 4-wire cable having only
2 pairs connected.
Last patch in the series is a fix that was required for testing, which
should make it to -stable, which I can submit separate against net if
you prefer David.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 22 Nov 2016 19:40:58 +0000 (11:40 -0800)]
net: dsa: bcm_sf2: Ensure we re-negotiate EEE during after link change
In case the link change and EEE is enabled or disabled, always try to
re-negotiate this with the link partner.
Fixes: 450b05c15f9c ("net: dsa: bcm_sf2: add support for controlling EEE") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 22 Nov 2016 19:40:57 +0000 (11:40 -0800)]
net: phy: bcm7xxx: Add support for downshift/Wirespeed
Add support for configuring the downshift/Wirespeed enable/disable
toggles and specify a link retry value ranging from 1 to 9. Since the
integrated BCM7xxx have issues when wirespeed is enabled and EEE is also
enabled, we do disable EEE if wirespeed is enabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 22 Nov 2016 19:40:56 +0000 (11:40 -0800)]
net: phy: broadcom: Allow enabling or disabling of EEE
In preparation for adding support for Wirespeed/downshift, we need to
change bcm_phy_eee_enable() to allow enabling or disabling EEE, so make
the function take an extra enable/disable boolean parameter and rename
it to illustrate it sets EEE, not necessarily just enables it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 22 Nov 2016 19:40:55 +0000 (11:40 -0800)]
net: phy: broadcom: Add support code for downshift/Wirespeed
Broadcom's Wirespeed feature allows us to configure how auto-negotiation
should behave with fewer working pairs of wires on a cable. Add support
code for retrieving and setting such downshift counters using the
recently added ethtool downshift tunables.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Make it possible to generate trace events for mdio read and write accesses.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org> Acked-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Hajnoczi [Mon, 21 Nov 2016 13:56:31 +0000 (13:56 +0000)]
VSOCK: add loopback to virtio_transport
The VMware VMCI transport supports loopback inside virtual machines.
This patch implements loopback for virtio-vsock.
Flow control is handled by the virtio-vsock protocol as usual. The
sending process stops transmitting on a connection when the peer's
receive buffer space is exhausted.
Cathy Avery <cavery@redhat.com> noticed this difference between VMCI and
virtio-vsock when a test case using loopback failed. Although loopback
isn't the main point of AF_VSOCK, it is useful for testing and
virtio-vsock must match VMCI semantics so that userspace programs run
regardless of the underlying transport.
My understanding is that loopback is not supported on the host side with
VMCI. Follow that by implementing it only in the guest driver, not the
vhost host driver.
Cc: Jorgen Hansen <jhansen@vmware.com> Reported-by: Cathy Avery <cavery@redhat.com> Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Tue, 22 Nov 2016 14:21:22 +0000 (15:21 +0100)]
marvell: mark mvneta and mvpp2 32-bit only
Both of these drivers won't work on 64-bit architectures unless they
are redesigned, since they store a virtual address pointer in a 32-bit
field of the descriptors:
drivers/net/ethernet/marvell/mvneta_bm.c: In function 'mvneta_bm_construct':
drivers/net/ethernet/marvell/mvneta_bm.c:103:16: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
drivers/net/ethernet/marvell/mvpp2.c: In function 'mvpp2_prs_vlan_init':
drivers/net/ethernet/marvell/mvpp2.c:2563:32: error: large integer implicitly truncated to unsigned type [-Werror=overflow]
This limits the COMPILE_TEST option for the two drivers again to
only build them on 32-bit. This seems nicer than shutting up the
warnings, in case we ever actually want to use them on 64-bit,
as the warnings indicate which parts of the driver are currently
broken there.
Fixes: a0627f776a45 ("net: marvell: Allow drivers to be built with COMPILE_TEST") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Tue, 22 Nov 2016 10:24:13 +0000 (11:24 +0100)]
mlxsw: core: Implement thermal zone
Implement thermal zone for mlxsw based HW. It uses temperature sensor
provided by ASIC (the same as mlxsw hwmon interface) to report current
temp to thermal core. The ASIC's PWM is then used to control speed
of system fans registered as cooling devices.
Signed-off-by: Ivan Vecera <cera@cera.cz> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Tue, 22 Nov 2016 10:24:12 +0000 (11:24 +0100)]
mlxsw: reg: Add Management Fan Speed Limit register
The MFSL register is used to configure the fan speed event / interrupt
notification mechanism. Fan speed threshold are defined for both
under-speed and over-speed.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 22 Nov 2016 14:55:32 +0000 (09:55 -0500)]
Merge branch 'mv88e6390-initial-support'
Andrew Lunn says:
====================
Start adding support for mv88e6390
This is the first patchset implementing support for the mv88e6390
family. This is a new generation of switch devices and has numerous
incompatible changes to the registers. These patches allow the switch
to the detected during probe, and makes the statistics unit work.
These patches are insufficient to make the mv88e6390 functional. More
patches will follow.
v2:
Move stats code into global1
Change DT compatible string to mv88e6190
Fixed mv88e6351 stats which v1 had broken
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 uses a different bit to select between bank0 and bank1
of the statistics. So implement an ops function for this, and pass the
selector bit to the generic stats read function. Also, the histogram
selection has moved for the mv88e6390, so abstract its selection as
well.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Mon, 21 Nov 2016 22:27:03 +0000 (23:27 +0100)]
net: dsa: mv88e6xxx: Add stats_get_stats to ops structure
Different families have different sets of statistics. Abstract this
using a stats_get_stats op. The mv88e6390 needs a different
implementation, which will be added later.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Mon, 21 Nov 2016 22:27:02 +0000 (23:27 +0100)]
net: dsa: mv88e6xxx: Add stats_get_sset_count|string to ops structure
Different families have different sets of statistics. Abstract this
using a stats_get_sset_count and stats_get_strings op. Each stat has a
bitmap, and the ops implementer uses a bit map mask to count the
statistics which apply for the family, or return the list of strings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
Rename functions to avoid _ prefix. Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Mon, 21 Nov 2016 22:27:01 +0000 (23:27 +0100)]
net: dsa: mv88e6xxx: Add mv88e6390 statistics unit init
The statistics unit on the mv88e6390 needs the histogram mode to be
configured in a different register compared to other devices. Add an
ops to do this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
Rename to mv88e6390_g1_stats_set_histogram
Move into global1.c Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6390 has a control register for what the histogram statistics
actually contain. This means the stat_snapshot method should not set
this information. So implement the 6390 stats_snapshot function without
these bits.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Mon, 21 Nov 2016 22:26:59 +0000 (23:26 +0100)]
net: dsa: mv88e6xxx: Add comment about family a device belongs to
Knowing the family of device belongs to helps with picking the ops
implementation which is appropriate to the device. So add a comment to
each structure of ops.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Mon, 21 Nov 2016 22:26:58 +0000 (23:26 +0100)]
net: dsa: mv88e6xxx: Abstract stats_snapshot into ops structure
Taking a stats snapshot differs between same families. Abstract this
into an ops member. At the same time, move the code into global1.[ch],
since the registers are in the global1 range.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Mon, 21 Nov 2016 22:26:57 +0000 (23:26 +0100)]
net: dsa: mv88e6xxx: Add the mv88e6390 family
With the devices added to the tables, the probe will recognize the
switch. This however is not sufficient to make it work properly, other
changes are needed because of incompatibilities.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Mon, 21 Nov 2016 22:26:56 +0000 (23:26 +0100)]
net: dsa: mv88e6xxx: Fix unused variable warning by using variable
_mv88e6xxx_stats_wait() did not check the return value from
mv88e6xxx_g1_read(), so the compiler complained about set but unused
err.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Mon, 21 Nov 2016 22:26:55 +0000 (23:26 +0100)]
net: dsa: mv88e6xxx: Take switch out of reset before probe
The switch needs to be taken out of reset before we can read its ID
register on the MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 21 Nov 2016 23:27:41 +0000 (15:27 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull apparmor bugfix from James Morris:
"This has a fix for a policy replacement bug that is fairly serious for
apache mod_apparmor users, as it results in the wrong policy being
applied on an network facing service"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
apparmor: fix change_hat not finding hat after policy replacement
1) With modern networking cards we can run out of 32-bit DMA space, so
support 64-bit DMA addressing when possible on sparc64. From Dave
Tushar.
2) Some signal frame validation checks are inverted on sparc32, fix
from Andreas Larsson.
3) Lockdep tables can get too large in some circumstances on sparc64,
add a way to adjust the size a bit. From Babu Moger.
4) Fix NUMA node probing on some sun4v systems, from Thomas Tai.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: drop duplicate header scatterlist.h
lockdep: Limit static allocations if PROVE_LOCKING_SMALL is defined
config: Adding the new config parameter CONFIG_PROVE_LOCKING_SMALL for sparc
sunbmac: Fix compiler warning
sunqe: Fix compiler warnings
sparc64: Enable 64-bit DMA
sparc64: Enable sun4v dma ops to use IOMMU v2 APIs
sparc64: Bind PCIe devices to use IOMMU v2 service
sparc64: Initialize iommu_map_table and iommu_pool
sparc64: Add ATU (new IOMMU) support
sparc64: Add FORCE_MAX_ZONEORDER and default to 13
sparc64: fix compile warning section mismatch in find_node()
sparc32: Fix inverted invalid_frame_pointer checks on sigreturns
sparc64: Fix find_node warning if numa node cannot be found
1) Clear congestion control state when changing algorithms on an
existing socket, from Florian Westphal.
2) Fix register bit values in altr_tse_pcs portion of stmmac driver,
from Jia Jie Ho.
3) Fix PTP handling in stammc driver for GMAC4, from Giuseppe
CAVALLARO.
4) Fix udplite multicast delivery handling, it ignores the udp_table
parameter passed into the lookups, from Pablo Neira Ayuso.
5) Synchronize the space estimated by rtnl_vfinfo_size and the space
actually used by rtnl_fill_vfinfo. From Sabrina Dubroca.
6) Fix memory leak in fib_info when splitting nodes, from Alexander
Duyck.
7) If a driver does a napi_hash_del() explicitily and not via
netif_napi_del(), it must perform RCU synchronization as needed. Fix
this in virtio-net and bnxt drivers, from Eric Dumazet.
8) Likewise, it is not necessary to invoke napi_hash_del() is we are
also doing neif_napi_del() in the same code path. Remove such calls
from be2net and cxgb4 drivers, also from Eric Dumazet.
9) Don't allocate an ID in peernet2id_alloc() if the netns is dead,
from WANG Cong.
10) Fix OF node and device struct leaks in of_mdio, from Johan Hovold.
11) We cannot cache routes in ip6_tunnel when using inherited traffic
classes, from Paolo Abeni.
12) Fix several crashes and leaks in cpsw driver, from Johan Hovold.
13) Splice operations cannot use freezable blocking calls in AF_UNIX,
from WANG Cong.
14) Link dump filtering by master device and kind support added an error
in loop index updates during the dump if we actually do filter, fix
from Zhang Shengju.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
tcp: zero ca_priv area when switching cc algorithms
net: l2tp: Treat NET_XMIT_CN as success in l2tp_eth_dev_xmit
ethernet: stmmac: make DWMAC_STM32 depend on it's associated SoC
tipc: eliminate obsolete socket locking policy description
rtnl: fix the loop index update error in rtnl_dump_ifinfo()
l2tp: fix racy SOCK_ZAPPED flag check in l2tp_ip{,6}_bind()
net: macb: add check for dma mapping error in start_xmit()
rtnetlink: fix FDB size computation
netns: fix get_net_ns_by_fd(int pid) typo
af_unix: conditionally use freezable blocking calls in read
net: ethernet: ti: cpsw: fix fixed-link phy probe deferral
net: ethernet: ti: cpsw: add missing sanity check
net: ethernet: ti: cpsw: fix secondary-emac probe error path
net: ethernet: ti: cpsw: fix of_node and phydev leaks
net: ethernet: ti: cpsw: fix deferred probe
net: ethernet: ti: cpsw: fix mdio device reference leak
net: ethernet: ti: cpsw: fix bad register access in probe error path
net: sky2: Fix shutdown crash
cfg80211: limit scan results cache size
net sched filters: pass netlink message flags in event notification
...
Declare the structure ieee802154_ops as const as it is only passed as an
argument to the function ieee802154_alloc_hw. This argument is of type
const struct ieee802154_ops *, so ieee80254_ops structures having this
property can be declared as const.
Done using Coccinelle:
The before and after size details of the affected files are:
text data bss dec hex filename
8669 1176 16 9861 2685 drivers/net/ieee802154/adf7242.o
8805 1048 16 9869 268d drivers/net/ieee802154/adf7242.o
text data bss dec hex filename
7211 2296 32 9539 2543 drivers/net/ieee802154/atusb.o
7339 2160 32 9531 253b drivers/net/ieee802154/atusb.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com> Acked-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 21 Nov 2016 19:05:50 +0000 (14:05 -0500)]
Merge branch 'geneve-lwt-efficiency'
Pravin B Shelar says:
====================
geneve: Use LWT more effectively.
Following patch series make use of geneve LWT code path for
geneve netdev type of device.
This allows us to simplify geneve module without changing any
functionality.
v2-v3:
Rebase against latest net-next.
v1-v2:
Fix warning reported by kbuild test robot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
pravin shelar [Mon, 21 Nov 2016 19:03:01 +0000 (11:03 -0800)]
geneve: Optimize geneve device lookup.
Rather than comparing 64-bit tunnel-id, compare tunnel vni
which is 24-bit id. This also save conversion from vni
to tunnel id on each tunnel packet receive.
Signed-off-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
pravin shelar [Mon, 21 Nov 2016 19:02:58 +0000 (11:02 -0800)]
geneve: Unify LWT and netdev handling.
Current geneve implementation has two separate cases to handle.
1. netdev xmit
2. LWT xmit.
In case of netdev, geneve configuration is stored in various
struct geneve_dev members. For example geneve_addr, ttl, tos,
label, flags, dst_cache, etc. For LWT ip_tunnel_info is passed
to the device in ip_tunnel_info.
Following patch uses ip_tunnel_info struct to store almost all
of configuration of a geneve netdevice. This allows us to unify
most of geneve driver code around ip_tunnel_info struct.
This dramatically simplify geneve code, since it does not
need to handle two different configuration cases. Removes
duplicate code, single code path can handle either type
of geneve devices.
Signed-off-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 21 Nov 2016 18:20:17 +0000 (13:20 -0500)]
Merge branch 'tcp-cong-undo_cwnd-mandatory'
Florian Westphal says:
====================
tcp: make undo_cwnd mandatory for congestion modules
highspeed, illinois, scalable, veno and yeah congestion control algorithms
don't provide a 'cwnd_undo' function. This makes the stack default to a
'reno undo' which doubles cwnd. However, the ssthresh implementation of
these algorithms do not halve the slowstart threshold. This causes similar
issue as the one fixed for dctcp in ce6dd23329b1e ("dctcp: avoid bogus
doubling of cwnd after loss").
In light of this it seems better to remove the fallback and make undo_cwnd
mandatory.
First patch fixes those spots where reno undo seems incorrect by providing
.cwnd_undo functions, second patch removes the fallback.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Mon, 21 Nov 2016 13:18:38 +0000 (14:18 +0100)]
tcp: make undo_cwnd mandatory for congestion modules
The undo_cwnd fallback in the stack doubles cwnd based on ssthresh,
which un-does reno halving behaviour.
It seems more appropriate to let congctl algorithms pair .ssthresh
and .undo_cwnd properly. Add a 'tcp_reno_undo_cwnd' function and wire it
up for all congestion algorithms that used to rely on the fallback.
Cc: Eric Dumazet <edumazet@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Neal Cardwell <ncardwell@google.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Mon, 21 Nov 2016 13:18:37 +0000 (14:18 +0100)]
tcp: add cwnd_undo functions to various tcp cc algorithms
congestion control algorithms that do not halve cwnd in their .ssthresh
should provide a .cwnd_undo rather than rely on current fallback which
assumes reno halving (and thus doubles the cwnd).
All of these do 'something else' in their .ssthresh implementation, thus
store the cwnd on loss and provide .undo_cwnd to restore it again.
A followup patch will remove the fallback and all algorithms will
need to provide a .cwnd_undo function.
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 21 Nov 2016 18:16:59 +0000 (13:16 -0500)]
Merge branch 'bridge-igmpv3-mldv2-support'
Nikolay Aleksandrov says:
====================
bridge: add support for IGMPv3 and MLDv2 querier
This patch-set adds support for IGMPv3 and MLDv2 querier in the bridge.
Two new options which can be toggled via netlink and sysfs are added that
control the version per-bridge:
multicast_igmp_version - default 2, can be set to 3
multicast_mld_version - default 1, can be set to 2 (this option is
disabled if CONFIG_IPV6=n)
Note that the names do not include "querier", I think that these options
can be re-used later as more IGMPv3 support is added to the bridge so we
can avoid adding more options to switch between v2 and v3 behaviour.
The set uses the already existing br_ip{4,6}_multicast_alloc_query
functions and adds the appropriate header based on the chosen version.
For the initial support I have removed the compatibility implementation
(RFC3376 sec 7.3.1, 7.3.2; RFC3810 sec 8.3.1, 8.3.2), because there are
some details that we need to sort out.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic support for MLDv2 queries, the default is MLDv1
as before. A new multicast option - multicast_mld_version, adds the
ability to change it between 1 and 2 via netlink and sysfs.
The MLD option is disabled if CONFIG_IPV6 is disabled.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic support for IGMPv3 queries, the default is IGMPv2
as before. A new multicast option - multicast_igmp_version, adds the
ability to change it between 2 and 3 via netlink and sysfs. The option
struct member is in a 4 byte hole in net_bridge.
There also a few minor style adjustments in br_multicast_new_group and
br_multicast_add_group.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Mon, 21 Nov 2016 09:08:37 +0000 (10:08 +0100)]
tcp: zero ca_priv area when switching cc algorithms
We need to zero out the private data area when application switches
connection to different algorithm (TCP_CONGESTION setsockopt).
When congestion ops get assigned at connect time everything is already
zeroed because sk_alloc uses GFP_ZERO flag. But in the setsockopt case
this contains whatever previous cc placed there.
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Gao Feng [Mon, 21 Nov 2016 00:56:21 +0000 (08:56 +0800)]
net: l2tp: Treat NET_XMIT_CN as success in l2tp_eth_dev_xmit
The tc could return NET_XMIT_CN as one congestion notification, but
it does not mean the packe is lost. Other modules like ipvlan,
macvlan, and others treat NET_XMIT_CN as success too.
So l2tp_eth_dev_xmit should add the NET_XMIT_CN check.
Signed-off-by: Gao Feng <gfree.wind@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 20 Nov 2016 17:24:36 +0000 (09:24 -0800)]
mlx4: avoid unnecessary dirtying of critical fields
While stressing a 40Gbit mlx4 NIC with busy polling, I found false
sharing in mlx4 driver that can be easily avoided.
This patch brings an additional 7 % performance improvement in UDP_RR
workload.
1) If we received no frame during one mlx4_en_process_rx_cq()
invocation, no need to call mlx4_cq_set_ci() and/or dirty ring->cons
2) Do not refill rx buffers if we have plenty of them.
This avoids false sharing and allows some bulk/batch optimizations.
Page allocator and its locks will thank us.
Finally, mlx4_en_poll_rx_cq() should not return 0 if it determined
cpu handling NIC IRQ should be changed. We should return budget-1
instead, to not fool net_rx_action() and its netdev_budget.
v2: keep AVG_PERF_COUNTER(... polled) even if polled is 0
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 21 Nov 2016 16:25:59 +0000 (11:25 -0500)]
Merge branch 'mlx5-bpf-refcnt-fixes'
Daniel Borkmann says:
====================
Couple of BPF refcount fixes for mlx5
Various mlx5 bugs on eBPF refcount handling found during review.
Last patch in series adds a __must_check to BPF helpers to make
sure we won't run into it again w/o compiler complaining first.
v2 -> v3:
- Just reworked patch 2/4 so we don't need bpf_prog_sub().
- Rebased, rest as is.
v1 -> v2:
- After discussion with Alexei, we agreed upon rebasing the
patches against net-next.
- Since net-next, I've also added the __must_check to enforce
future users to check for errors.
- Fixed up commit message #2.
- Simplify assignment from patch #1 based on Saeed's feedback
on previous set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sat, 19 Nov 2016 00:45:03 +0000 (01:45 +0100)]
bpf: add __must_check attributes to refcount manipulating helpers
Helpers like bpf_prog_add(), bpf_prog_inc(), bpf_map_inc() can fail
with an error, so make sure the caller properly checks their return
value and not just ignores it, which could worst-case lead to use
after free.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sat, 19 Nov 2016 00:45:02 +0000 (01:45 +0100)]
bpf, mlx5: drop priv->xdp_prog reference on netdev cleanup
mlx5e_xdp_set() is currently the only place where we drop reference on the
prog sitting in priv->xdp_prog when it's exchanged by a new one. We also
need to make sure that we eventually release that reference, for example,
in case the netdev is dismantled, otherwise we leak the program.
Fixes: 86994156c736 ("net/mlx5e: XDP fast RX drop bpf programs support") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sat, 19 Nov 2016 00:45:01 +0000 (01:45 +0100)]
bpf, mlx5: fix various refcount issues in mlx5e_xdp_set
There are multiple issues in mlx5e_xdp_set():
1) The batched bpf_prog_add() is currently not checked for errors. When
doing so, it should be done at an earlier point in time to makes sure
that we cannot fail anymore at the time we want to set the program for
each channel. The batched refs short-cut can only be performed when we
don't need to perform a reset for changing the rq type and the device
was in opened state. In case the device was not in opened state, then
the next mlx5e_open_locked() will aquire the refs from the control prog
via mlx5e_create_rq(), same when we need to perform a reset.
2) When swapping the priv->xdp_prog, then no extra reference count must be
taken since we got that from call path via dev_change_xdp_fd() already.
Otherwise, we'd never be able to release the program. Also, bpf_prog_add()
without checking the return code could fail.
Fixes: 86994156c736 ("net/mlx5e: XDP fast RX drop bpf programs support") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sat, 19 Nov 2016 00:45:00 +0000 (01:45 +0100)]
bpf, mlx5: fix mlx5e_create_rq taking reference on prog
In mlx5e_create_rq(), when creating a new queue, we call bpf_prog_add() but
without checking the return value. bpf_prog_add() can fail since 92117d8443bc
("bpf: fix refcnt overflow"), so we really must check it. Take the reference
right when we assign it to the rq from priv->xdp_prog, and just drop the
reference on error path. Destruction in mlx5e_destroy_rq() looks good, though.
Fixes: 86994156c736 ("net/mlx5e: XDP fast RX drop bpf programs support") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Johansen [Thu, 1 Sep 2016 04:10:06 +0000 (21:10 -0700)]
apparmor: fix change_hat not finding hat after policy replacement
After a policy replacement, the task cred may be out of date and need
to be updated. However change_hat is using the stale profiles from
the out of date cred resulting in either: a stale profile being applied
or, incorrect failure when searching for a hat profile as it has been
migrated to the new parent profile.
Fixes: 01e2b670aa898a39259bc85c78e3d74820f4d3b6 (failure to find hat) Fixes: 898127c34ec03291c86f4ff3856d79e9e18952bc (stale policy being applied)
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1000287 Cc: stable@vger.kernel.org Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: James Morris <james.l.morris@oracle.com>
David S. Miller [Mon, 21 Nov 2016 02:16:14 +0000 (21:16 -0500)]
Merge branch 'mV88e6xxx-interrupt-fixes'
Andrew Lunn says:
====================
Fixes for the MV88e6xxx interrupt code
The interrupt code was never tested with a board who's probing
resulted in an -EPROBE_DEFFERED. So the clean up paths never got
tested. I now do have -EPROBE_DEFFERED, and things break badly during
cleanup. These are the fixes.
This is fixing code in net-next.
v2:
Fix typo pointed out by David Miller
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 20 Nov 2016 19:14:18 +0000 (20:14 +0100)]
net: dsa: mv88e6xxx: Fix releasing for the global2 interrupts
It is not possible to use devm_request_threaded_irq() because we have
two stacked interrupt controllers in one device. The lower interrupt
controller cannot be removed until the upper is fully removed. This
happens too late with the devm API, resulting in error messages about
removing a domain while there is still an active interrupt. Swap to
using request_threaded_irq() and manage the release of the interrupt
manually.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 20 Nov 2016 19:14:17 +0000 (20:14 +0100)]
net: dsa: mv88e6xxx: Fix cleanup on error for g1 interrupt setup
On error, remask the interrupts, release all maps, and remove the
domain. This cannot be done using the mv88e6xxx_g1_irq_free() because
some of these actions are not idempotent.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 20 Nov 2016 18:27:39 +0000 (10:27 -0800)]
Merge branch 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"A few more ARM fixes:
- the assembly backtrace code suffers problems with the new printk()
implementation which assumes that kernel messages without KERN_CONT
should have newlines inserted between them. Fix this.
- fix a section naming error - ".init.text" rather than ".text.init"
- preallocate DMA debug memory at core_initcall() time rather than
fs_initcall(), as we have some core drivers that need to use DMA
mapping - and that triggers a kernel warning from the DMA debug
code.
- fix XIP kernels after the ro_after_init changes made this data
permanently read-only"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: Fix XIP kernels
ARM: 8628/1: dma-mapping: preallocate DMA-debug hash tables in core_initcall
ARM: 8624/1: proc-v7m.S: fix init section name
ARM: fix backtrace
Zhang Shengju [Sat, 19 Nov 2016 15:28:32 +0000 (23:28 +0800)]
rtnl: fix the loop index update error in rtnl_dump_ifinfo()
If the link is filtered out, loop index should also be updated. If not,
loop index will not be correct.
Fixes: dc599f76c22b0 ("net: Add support for filtering link dump by master device and kind") Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Sat, 19 Nov 2016 01:08:08 +0000 (04:08 +0300)]
net: fix bogus cast in skb_pagelen() and use unsigned variables
1) cast to "int" is unnecessary:
u8 will be promoted to int before decrementing,
small positive numbers fit into "int", so their values won't be changed
during promotion.
Once everything is int including loop counters, signedness doesn't
matter: 32-bit operations will stay 32-bit operations.
But! Someone tried to make this loop smart by making everything of
the same type apparently in an attempt to optimise it.
Do the optimization, just differently.
Do the cast where it matters. :^)
2) frag size is unsigned entity and sum of fragments sizes is also
unsigned.
Make everything unsigned, leave no MOVSX instruction behind.
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-4 (-4)
function old new delta
skb_cow_data 835 834 -1
ip_do_fragment 2549 2548 -1
ip6_fragment 3130 3128 -2
Total: Before=154865032, After=154865028, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Sat, 19 Nov 2016 00:59:07 +0000 (03:59 +0300)]
netlink: smaller nla_attr_minlen table
Length of a netlink attribute may be u16 but lengths of basic attributes
are much smaller, so small we can save 16 bytes of .rodata and pocket
change inside .text.
16-bit is worse on x86-64 than 8-bit because of operand size override prefix.
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-19 (-19)
function old new delta
validate_nla 418 417 -1
nla_policy_len 66 64 -2
nla_attr_minlen 32 16 -16
Total: Before=154865051, After=154865032, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Fri, 18 Nov 2016 21:13:00 +0000 (22:13 +0100)]
l2tp: fix racy SOCK_ZAPPED flag check in l2tp_ip{,6}_bind()
Lock socket before checking the SOCK_ZAPPED flag in l2tp_ip6_bind().
Without lock, a concurrent call could modify the socket flags between
the sock_flag(sk, SOCK_ZAPPED) test and the lock_sock() call. This way,
a socket could be inserted twice in l2tp_ip6_bind_table. Releasing it
would then leave a stale pointer there, generating use-after-free
errors when walking through the list or modifying adjacent entries.
BUG: KASAN: use-after-free in l2tp_ip6_close+0x22e/0x290 at addr ffff8800081b0ed8
Write of size 8 by task syz-executor/10987
CPU: 0 PID: 10987 Comm: syz-executor Not tainted 4.8.0+ #39
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.8.2-0-g33fbe13 by qemu-project.org 04/01/2014 ffff880031d97838ffffffff829f835bffff88001b5a1640ffff8800081b0ec0 ffff8800081b15a0ffff8800081b6d20ffff880031d97860ffffffff8174d3cc ffff880031d978f0ffff8800081b0e80ffff88001b5a1640ffff880031d978e0
Call Trace:
[<ffffffff829f835b>] dump_stack+0xb3/0x118 lib/dump_stack.c:15
[<ffffffff8174d3cc>] kasan_object_err+0x1c/0x70 mm/kasan/report.c:156
[< inline >] print_address_description mm/kasan/report.c:194
[<ffffffff8174d666>] kasan_report_error+0x1f6/0x4d0 mm/kasan/report.c:283
[< inline >] kasan_report mm/kasan/report.c:303
[<ffffffff8174db7e>] __asan_report_store8_noabort+0x3e/0x40 mm/kasan/report.c:329
[< inline >] __write_once_size ./include/linux/compiler.h:249
[< inline >] __hlist_del ./include/linux/list.h:622
[< inline >] hlist_del_init ./include/linux/list.h:637
[<ffffffff8579047e>] l2tp_ip6_close+0x22e/0x290 net/l2tp/l2tp_ip6.c:239
[<ffffffff850b2dfd>] inet_release+0xed/0x1c0 net/ipv4/af_inet.c:415
[<ffffffff851dc5a0>] inet6_release+0x50/0x70 net/ipv6/af_inet6.c:422
[<ffffffff84c4581d>] sock_release+0x8d/0x1d0 net/socket.c:570
[<ffffffff84c45976>] sock_close+0x16/0x20 net/socket.c:1017
[<ffffffff817a108c>] __fput+0x28c/0x780 fs/file_table.c:208
[<ffffffff817a1605>] ____fput+0x15/0x20 fs/file_table.c:244
[<ffffffff813774f9>] task_work_run+0xf9/0x170
[<ffffffff81324aae>] do_exit+0x85e/0x2a00
[<ffffffff81326dc8>] do_group_exit+0x108/0x330
[<ffffffff81348cf7>] get_signal+0x617/0x17a0 kernel/signal.c:2307
[<ffffffff811b49af>] do_signal+0x7f/0x18f0
[<ffffffff810039bf>] exit_to_usermode_loop+0xbf/0x150 arch/x86/entry/common.c:156
[< inline >] prepare_exit_to_usermode arch/x86/entry/common.c:190
[<ffffffff81006060>] syscall_return_slowpath+0x1a0/0x1e0 arch/x86/entry/common.c:259
[<ffffffff85e4d726>] entry_SYSCALL_64_fastpath+0xc4/0xc6
Object at ffff8800081b0ec0, in cache L2TP/IPv6 size: 1448
Allocated:
PID = 10987
[ 1116.897025] [<ffffffff811ddcb6>] save_stack_trace+0x16/0x20
[ 1116.897025] [<ffffffff8174c736>] save_stack+0x46/0xd0
[ 1116.897025] [<ffffffff8174c9ad>] kasan_kmalloc+0xad/0xe0
[ 1116.897025] [<ffffffff8174cee2>] kasan_slab_alloc+0x12/0x20
[ 1116.897025] [< inline >] slab_post_alloc_hook mm/slab.h:417
[ 1116.897025] [< inline >] slab_alloc_node mm/slub.c:2708
[ 1116.897025] [< inline >] slab_alloc mm/slub.c:2716
[ 1116.897025] [<ffffffff817476a8>] kmem_cache_alloc+0xc8/0x2b0 mm/slub.c:2721
[ 1116.897025] [<ffffffff84c4f6a9>] sk_prot_alloc+0x69/0x2b0 net/core/sock.c:1326
[ 1116.897025] [<ffffffff84c58ac8>] sk_alloc+0x38/0xae0 net/core/sock.c:1388
[ 1116.897025] [<ffffffff851ddf67>] inet6_create+0x2d7/0x1000 net/ipv6/af_inet6.c:182
[ 1116.897025] [<ffffffff84c4af7b>] __sock_create+0x37b/0x640 net/socket.c:1153
[ 1116.897025] [< inline >] sock_create net/socket.c:1193
[ 1116.897025] [< inline >] SYSC_socket net/socket.c:1223
[ 1116.897025] [<ffffffff84c4b46f>] SyS_socket+0xef/0x1b0 net/socket.c:1203
[ 1116.897025] [<ffffffff85e4d685>] entry_SYSCALL_64_fastpath+0x23/0xc6
Freed:
PID = 10987
[ 1116.897025] [<ffffffff811ddcb6>] save_stack_trace+0x16/0x20
[ 1116.897025] [<ffffffff8174c736>] save_stack+0x46/0xd0
[ 1116.897025] [<ffffffff8174cf61>] kasan_slab_free+0x71/0xb0
[ 1116.897025] [< inline >] slab_free_hook mm/slub.c:1352
[ 1116.897025] [< inline >] slab_free_freelist_hook mm/slub.c:1374
[ 1116.897025] [< inline >] slab_free mm/slub.c:2951
[ 1116.897025] [<ffffffff81748b28>] kmem_cache_free+0xc8/0x330 mm/slub.c:2973
[ 1116.897025] [< inline >] sk_prot_free net/core/sock.c:1369
[ 1116.897025] [<ffffffff84c541eb>] __sk_destruct+0x32b/0x4f0 net/core/sock.c:1444
[ 1116.897025] [<ffffffff84c5aca4>] sk_destruct+0x44/0x80 net/core/sock.c:1452
[ 1116.897025] [<ffffffff84c5ad33>] __sk_free+0x53/0x220 net/core/sock.c:1460
[ 1116.897025] [<ffffffff84c5af23>] sk_free+0x23/0x30 net/core/sock.c:1471
[ 1116.897025] [<ffffffff84c5cb6c>] sk_common_release+0x28c/0x3e0 ./include/net/sock.h:1589
[ 1116.897025] [<ffffffff8579044e>] l2tp_ip6_close+0x1fe/0x290 net/l2tp/l2tp_ip6.c:243
[ 1116.897025] [<ffffffff850b2dfd>] inet_release+0xed/0x1c0 net/ipv4/af_inet.c:415
[ 1116.897025] [<ffffffff851dc5a0>] inet6_release+0x50/0x70 net/ipv6/af_inet6.c:422
[ 1116.897025] [<ffffffff84c4581d>] sock_release+0x8d/0x1d0 net/socket.c:570
[ 1116.897025] [<ffffffff84c45976>] sock_close+0x16/0x20 net/socket.c:1017
[ 1116.897025] [<ffffffff817a108c>] __fput+0x28c/0x780 fs/file_table.c:208
[ 1116.897025] [<ffffffff817a1605>] ____fput+0x15/0x20 fs/file_table.c:244
[ 1116.897025] [<ffffffff813774f9>] task_work_run+0xf9/0x170
[ 1116.897025] [<ffffffff81324aae>] do_exit+0x85e/0x2a00
[ 1116.897025] [<ffffffff81326dc8>] do_group_exit+0x108/0x330
[ 1116.897025] [<ffffffff81348cf7>] get_signal+0x617/0x17a0 kernel/signal.c:2307
[ 1116.897025] [<ffffffff811b49af>] do_signal+0x7f/0x18f0
[ 1116.897025] [<ffffffff810039bf>] exit_to_usermode_loop+0xbf/0x150 arch/x86/entry/common.c:156
[ 1116.897025] [< inline >] prepare_exit_to_usermode arch/x86/entry/common.c:190
[ 1116.897025] [<ffffffff81006060>] syscall_return_slowpath+0x1a0/0x1e0 arch/x86/entry/common.c:259
[ 1116.897025] [<ffffffff85e4d726>] entry_SYSCALL_64_fastpath+0xc4/0xc6
Memory state around the buggy address: ffff8800081b0d80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8800081b0e00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff8800081b0e80: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
^ ffff8800081b0f00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8800081b0f80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Linus Torvalds [Sun, 20 Nov 2016 02:40:47 +0000 (18:40 -0800)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Again a set of smaller fixes across several platforms (OMAP, Marvell,
Allwinner, i.MX, etc).
A handful of typo fixes and smaller missing contents from device
trees, with some tweaks to OMAP mach files to deal with CPU feature
print misformatting, potential NULL ptr dereference and one setup
issue with UARTs"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ipmi/bt-bmc: change compatible node to 'aspeed, ast2400-ibt-bmc'
ARM: dts: STiH410-b2260: Fix typo in spi0 chipselect definition
ARM: dts: omap5: board-common: fix wrong SMPS6 (VDD-DDR3) voltage
ARM: omap3: Add missing memory node in SOM-LV
arm64: dts: marvell: add unique identifiers for Armada A8k SPI controllers
arm64: dts: marvell: fix clocksource for CP110 slave SPI0
arm64: dts: marvell: Fix typo in label name on Armada 37xx
ASoC: omap-abe-twl6040: fix typo in bindings documentation
dts: omap5: board-common: enable twl6040 headset jack detection
dts: omap5: board-common: add phandle to reference Palmas gpadc
ARM: OMAP2+: avoid NULL pointer dereference
ARM: OMAP2+: PRM: initialize en_uart4_mask and grpsel_uart4_mask
ARM: dts: omap3: Fix memory node in Torpedo board
ARM: AM43XX: Select OMAP_INTERCONNECT in Kconfig
ARM: OMAP3: Fix formatting of features printed
ARM: dts: imx53-qsb: Fix regulator constraints
ARM: dts: sun8i: fix the pinmux for UART1
projects / linux-beck.git / log