serial: imx: Use generic uart-has-rtscts DT property
Convert the Freescale IMX UART driver from using the vendor-specific
"fsl,uart-has-rtscts" to the generic "uart-has-rtscts" DT property, as
documented by the Generic Serial DT Bindings.
The old vendor-specific property is still recognized by the driver for
backwards compatibility, but deprecated.
Document a set of generic properties for describing UARTs in a
device tree:
1. The GPIO modem control properties are currently duplicated across
hardware-specific binding documentation,
2. The property for dedicated RTS/CTS hardware flow control lines is
already supported by several drivers, albeit with a vendor-specific
prefix, hence make it generic.
Peter Hurley [Sun, 10 Apr 2016 05:14:36 +0000 (22:14 -0700)]
serial: 8250: Extract IIR logic steering from rx dma
Using fake IIR values to perform rx dma operations unnecessarily
conflates separate operations, stopping in-progress dma with starting
new dma.
Introduce serial8250_rx_dma_flush() to handle stopping in-progress dma
[omap8250 already has equivalent omap_8250_rx_dma_flush()].
Replace rx_dma(UART_IIR_RX_TIMEOUT) with the equivalent *_rx_dma_flush(),
and rx_dma(0) with the equivalent *_rx_dma(). Handle IIR steering
in the irq handler with handle_rx_dma() helper.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 10 Apr 2016 05:14:34 +0000 (22:14 -0700)]
serial: omap8250: Drop rx buffer sync
commit 27c310c5c312 ("serial: 8250_dma: no need to sync RX buffer")
notes the RX DMA buffer is allocated from DMA coherent memory, and
thus does not need sync'd for each transaction. The same is true
for OMAP RX DMA.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 dma support requires the dmaegine driver support terminate.
Query slave caps to determine if necessary commands/properties are
supported; disable dma if not.
Note this means dmaengine driver must support slave caps reporting
as well.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 dma support requires the dmaengine driver support error-free
pause/terminate and better-than-descriptor residue granularity. Query
slave caps to determine if necessary commands/properties are supported;
disable dma if not.
Note this means dmaengine driver must support slave caps reporting
as well.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ->get_char() returns a negative error code and that can mean that
"ch" is uninitialized. The callers of this function expect NO_POLL_CHAR
on error so let's return that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We reach this point of code after a test of 'info->port.tty->hw_stopped',
we do not need to test for 'info->port.tty' as it is obvious that
info->port.tty is not NULL now, we have already dereferenced it.
On Intel Penwell and Tangier the HSU block (3 HSU ports) has a global register
set which is currently not used by the driver. On Tangier it has it's own PCI
device and thus available for enumeration. Since it's not a real HSU port we
just skip it and therefore put a comment in the code why we do so.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko [Mon, 4 Apr 2016 14:35:09 +0000 (17:35 +0300)]
serial: 8250_mid: use proper bar for DNV platform
Unlike Intel Medfield and Tangier platforms DNV uses PCI BAR0 for IO compatible
resources and BAR1 for MMIO. We need latter in a way to support DMA. Introduce
an additional field in the internal structure and pass PCI BAR based on device
ID.
Reported-by: "Lai, Poey Seng" <poey.seng.lai@intel.com> Fixes: 6ede6dcd87aa ("serial: 8250_mid: add support for DMA engine handling from UART MMIO") Cc: stable@vger.kernel.org Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: 8250_pci: report DCD and DSR signals as active for Bay Trail
Bay Trail UART port does not support DCD and DSR lines. The driver
shall report that these signals are permanently active. This patch
is for HSUART enumerated via PCI.
For ACPI, see commit dfd37668ea6d ("serial: 8250_dw: Fix get_mctrl
behaviour"). The commit also describes the possible issue if these
signals are enabled on a port without these pins.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exposes get_mctrl() function so that it can be overriden with platform
specific implementation.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Slaby [Thu, 31 Mar 2016 08:23:34 +0000 (10:23 +0200)]
TTY: serial/ifx6x60, initialize more
In ifx_spi_complete, 'more' is not initialized. It is set only if the
status is clear and only if the header is parsed OK. If any of those
is not true, 'more' can be used uninitialized in that function later.
Jiri Slaby [Thu, 31 Mar 2016 08:08:15 +0000 (10:08 +0200)]
tty: vt, get rid of weird source code flow
Some code in vc_allocate is indented by 4 spaces. It is inside a
condition. Invert the condition and move the code to the first
indentation level (using \tab). And insert some empty lines to have
logical code blocks separated.
Then, instead of freeing in an 'if' false branch, use goto-error
label as fail path.
Maybe better to look at this patch with diff -w -b.
serial: samsung: Reorder the sequence of clock control when call s3c24xx_serial_set_termios()
This patch fixes the broken serial log when changing the clock source
of uart device. Before disabling the original clock source, this patch
enables the new clock source to protect the clock off state for a split second.
MIPS: ath79: make bootconsole wait for both THRE and TEMT
This makes the ath79 bootconsole behave the same way as the generic 8250
bootconsole.
Also waiting for TEMT (transmit buffer is empty) instead of just THRE
(transmit buffer is not full) ensures that all characters have been
transmitted before the real serial driver starts reconfiguring the serial
controller (which would sometimes result in garbage being transmitted.)
This change does not cause a visible performance loss.
In addition, this seems to fix a hang observed in certain configurations on
many AR7xxx/AR9xxx SoCs during autoconfig of the real serial driver.
A more complete follow-up patch will disable 8250 autoconfig for ath79
altogether (the serial controller is detected as a 16550A, which is not
fully compatible with the ath79 serial, and the autoconfig may lead to
undefined behavior on ath79.)
Stephen Boyd [Fri, 25 Mar 2016 21:35:49 +0000 (14:35 -0700)]
tty: serial: msm: Support more bauds
The msm_find_best_baud() function is written with the assumption
that the port->uartclk rate is fixed to a particular rate at boot
time, but now this driver changes that clk rate at runtime when
the baud is changed.
The way the hardware works is that an input clk rate comes from
the clk controller into the uart hw block. That rate is typically 1843200 or 3686400 Hz. That rate can then be divided by an
internal divider in the hw block to achieve a particular baud on
the serial wire. msm_find_best_baud() is looking for that divider
value.
A few things are wrong with the way the code is written. First,
it assumes that the maximum baud that the uart can support if the
clk rate is fixed at boot is 460800, which would correspond to an
input clk rate of 230400 * 16 == 3686400 Hz. Except some devices
have a boot rate of 1843200 Hz or max baud of 115200, so
achieving 230400 on those devices doesn't work at all because we
don't increase the clk rate unless max baud is 460800.
Second, we can't achieve bauds higher than 460800 that require
anything besides a divisor of 1, because we always call
msm_find_best_baud() with a fixed port->uartclk rate that will
eventually be changed after we calculate the divisor. So if we
need to get a baud of 500000, we'll just multiply that by 16 and
hope that the clk can give us 500000 * 16 == 8000000 Hz, which it
typically can't do. To really achieve 500000 baud, we need to get
an input clk rate of 24000000 Hz and then divide that by 3 inside
the uart hardware.
Finally, we return success for bauds even when we can't actually
achieve them. This means that when the user asks for 500000 baud,
we actually get 921600 right now, but the user doesn't know that.
Fix all of this by searching through the divisor and clk rate
space with a combination of clk_round_rate() and baud
calculations, keeping track of the best clk rate and divisor we
find if we can't get an exact match. Typically we can get an
exact match with a divisor of 1, but sometimes we need to keep
track and try more frequencies. On my msm8916 device, this
results in all standard bauds in baud_table being supported
except for 1800, 576000, 1152000, and 4000000.
Fixes: 850b37a71bde ("tty: serial: msm: Remove 115.2 Kbps maximum baud rate limitation") Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com> Cc: Matthew McClintock <mmcclint@codeaurora.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Acked-by: Andy Gross <andy.gross@linaro.org> Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> Tested-by: Cristian Prundeanu <cprundea@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to tty_ioctl(4) (from man-pages 4.04) the rng member only
counts 0->1 transitions. For the other signals (DSR, CD, CTS) both edges
are supposed to be counted.
Julia Lawall [Mon, 18 Apr 2016 14:55:37 +0000 (16:55 +0200)]
TTY: add __init attribute
Add __init attribute on a function that is only called from other __init
functions and that is not inlined, at least with gcc version 4.8.4 on an
x86 machine with allyesconfig. Currently, the function is put in the
.text.unlikely segment. Declaring it as __init will cause it to be put in
the .init.text and to disappear after initialization.
The result of objdump -x on the function before the change is as follows:
Done with the help of Coccinelle. The semantic patch checks for local
static non-init functions that are called from an __init function and are
not called from any other function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oleksij Rempel [Wed, 16 Mar 2016 13:05:52 +0000 (14:05 +0100)]
serial: mxs-auart: add Alphascale ASM9260 support
Alphascale ASM9260 uart IP has some common registers with
Freescale STMP37XX. This patch provide changes which
allow to reuse mxs-auart.c code for ASM9260.
SC16is7xx has feature for auto hardware flow control using RTS/CTS,
so we don't need "uart_handle_cts_change" to invoke "start_tx/stop_tx"
for flow control.
In addition, for software CTS, interrupt "SC16IS7XX_IIR_CTSRTS_SRC"
just report the nCTS change of state from active(low) to inactive(high),
driver don't know when the state of nCTS change from incactive to active,
so can't resume the transmission when a peer device is again ready and
re-assert nRTS signal.
Signed-off-by: Wills Wang <wills.wang@live.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Baruch Siach [Mon, 29 Feb 2016 12:34:10 +0000 (14:34 +0200)]
serial: imx: support RS-485 Rx disable on Tx
Some RS-232 to RS-485 transceivers require Rx to be disabled on Tx to
avoid echo of Tx data into the Rx buffer. Specifically, the XR3160E
RS-232/RS-485/RS-422 transceiver behaves this way.
This commit disables Rx on active Tx when SER_RS485_ENABLED is active and
SER_RS485_RX_DURING_TX is disabled.
Note that this is a change in behavior of the driver. Until now
SER_RS485_RX_DURING_TX was enabled unconditionally even when disabled in
the TIOCSRS485 ioctl serial_rs485 flags field.
Paul Gortmaker [Sun, 13 Mar 2016 23:48:52 +0000 (19:48 -0400)]
drivers/tty: make serial/mvebu-uart.c explicitly non-modular
The Kconfig currently controlling compilation of this code is:
drivers/tty/serial/Kconfig:config SERIAL_MVEBU_UART
drivers/tty/serial/Kconfig: bool "Marvell EBU serial port support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since the code wasn't using module_init to begin with, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Andreas Färber [Sun, 6 Mar 2016 11:21:24 +0000 (12:21 +0100)]
tty: serial: meson: Implement earlycon support
Split off the bulk of the existing meson_serial_console_write()
implementation into meson_serial_port_write() for implementing
meson_serial_early_console_write().
Use "meson" as the earlycon driver name, courtesy of Nicolas.
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com> Acked-by: Carlo Caione <carlo@endlessm.com> Signed-off-by: Andreas Färber <afaerber@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty: msm_serial: remove static clk rate setting in probe
The issue with setting up a fixed clock rate at probe is that it would
overwrite the console rate set by the bootloader for its console device.
This would result in serial out corruption or missing log when we system
is booted with earlycon. This is not a issue if we boot system without
earlycon.
This setup is at least not required with the mainline driver, this code
used to be required because the clk_enable() call would fail if
clk_set_rate() wasn't called first.
Originally the issue was noticed on DB410c which is based on APQ8016
chipset.
Without this patch the console log with earlycon would look like:
...
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=1
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
����+HH��0.699378] console [ttyMSM0] enabled
[ 0.699378] console [ttyMSM0] enabled
[ 0.702003] bootconsole [uart0] disabled
[ 0.702003] bootconsole [uart0] disabled
...
with this patch I can see all the skipped lines on the console
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Acked-by: Andy Gross <andy.gross@linaro.org> Tested-by: Pramod Gurav <gpramod@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 10 Apr 2016 01:56:35 +0000 (18:56 -0700)]
serial: core: Prevent unsafe uart port access, part 3
For tty operations which may expect uart port to have been removed
but still have other necessary work to accomplish, check for NULL
uart port; specifically uart_close(), uart_hangup() and sub-functions
(uart_shutdown() and uart_port_shutdown()).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 10 Apr 2016 01:56:34 +0000 (18:56 -0700)]
serial: core: Prevent unsafe uart port access, part 2
For serial core operations not already excluded by holding port->mutex,
use reference counting to protect deferencing the state->uart_port.
Introduce helper functions, uart_port_ref() and uart_port_deref(), to
wrap uart_port access, and helper macros, uart_port_lock() and
uart_port_unlock(), to wrap combination uart_port access with uart
port lock sections.
Port removal in uart_remove_one_port() waits for reference count to
drop to zero before detaching the uart port from struct uart_state.
For functions only reading the tx circular buffer indexes (where the
uart port lock is claimed to prevent concurrent users), a NULL uart
port is simply ignored and the operation completes normally.
For functions change the tx circular buffer indexes (where the uart
port lock is claimed to prevent concurrent users), the operation is
aborted if the uart port is NULL (ie., has been detached).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 10 Apr 2016 01:56:33 +0000 (18:56 -0700)]
serial: core: Prevent unsafe uart port access, part 1
uart_remove_one_port() may race with every serial core operation
requiring a valid dereference of state->uart_port. In particular,
uart_remove_one_port() may unlink the uart port concurrently with
any serial core operation that may dereference same.
Ensure safe dereference for those operations that already claim
the port->mutex, and extend that guarantee for trivial cases,
such as the ioctl handlers. Introduce the uart_port_check() helper
which asserts port->mutex is held (only when lockdep is on).
For ioctls, return -EIO as if the port has been hung up (since it has).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 10 Apr 2016 01:56:32 +0000 (18:56 -0700)]
serial: core: Expand port mutex section in uart_poll_init()
Prepare uart_poll_init() to safely dereference uart port; expand the
port mutex section to guarantee uart port remains valid until
uart_poll_init() completes.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 10 Apr 2016 00:53:27 +0000 (17:53 -0700)]
tty: core: Undefine ASYNC_* flags superceded by TTY_PORT* flags
Purposefully break out-of-tree driver compiles using kernel
ASYNC_* bits which have been superceded by TTY_PORT* flags and
their respective helper functions.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 10 Apr 2016 00:53:25 +0000 (17:53 -0700)]
tty: Replace ASYNC_INITIALIZED bit and update atomically
Replace ASYNC_INITIALIZED bit in the tty_port::flags field with
TTY_PORT_INITIALIZED bit in the tty_port::iflags field. Introduce helpers
tty_port_set_initialized() and tty_port_initialized() to abstract
atomic bit ops.
Note: the transforms for test_and_set_bit() and test_and_clear_bit()
are unnecessary as the state transitions are already mutually exclusive;
the tty lock prevents concurrent open/close/hangup.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 10 Apr 2016 00:53:24 +0000 (17:53 -0700)]
tty: Replace ASYNC_SUSPENDED bit and update atomically
Replace ASYNC_SUSPENDED bit in the tty_port::flags field with
TTY_PORT_SUSPENDED bit in the tty_port::iflags field. Introduce helpers
tty_port_set_suspended() and tty_port_suspended() to abstract
atomic bit ops.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 10 Apr 2016 00:53:23 +0000 (17:53 -0700)]
tty: Replace ASYNC_CHECK_CD and update atomically
Replace ASYNC_CHECK_CD bit in the tty_port::flags field with
TTY_PORT_CHECK_CD bit in the tty_port::iflags field. Introduce helpers
tty_port_set_check_carrier() and tty_port_check_carrier() to abstract
the atomic bit ops.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 10 Apr 2016 00:53:22 +0000 (17:53 -0700)]
tty: Replace ASYNC_NORMAL_ACTIVE bit and update atomically
Replace ASYNC_NORMAL_ACTIVE bit in the tty_port::flags field with
TTY_PORT_ACTIVE bit in the tty_port::iflags field. Introduce helpers
tty_port_set_active() and tty_port_active() to abstract atomic bit ops.
Extract state changes from port lock sections, as this usage is
broken and confused; the state transitions are protected by the
tty lock (which mutually excludes parallel open/close/hangup),
and no user tests the active state while holding the port lock.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 10 Apr 2016 00:53:21 +0000 (17:53 -0700)]
tty: Replace ASYNC_CTS_FLOW bit and update atomically
Replace ASYNC_CTS_FLOW bit in the tty_port::flags field with
TTY_PORT_CTS_FLOW bit in the tty_port::iflags field. Add
tty_port_set_cts_flow() helper to abstract the atomic bit ops.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 10 Apr 2016 00:53:20 +0000 (17:53 -0700)]
tty: Define ASYNC_ replacement bits
Prepare for relocating kernel private state bits out of tty_port::flags
field; tty_port::flags field is not atomic and can become corrupted
by concurrent updates. It also suffers from the complication of sharing
in a userspace-visible field which must be masked.
Define new tty_port::iflags field and new, substitute bit definitions
for the former ASYNC_* flags.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty: amba-pl011: Use 32-bit accesses for SBSA UART
Version 2 of the Server Base System Architecture (SBSAv2) describes UART
hardware registers as 32 bits wide, giving no guidance on access sizes. The
SBSA UART driver previously assumed partial-length 16 and 8 bit accesses would
work. But the SBSAv2 UART hardware on the Qualcomm Technologies QDF2432 only
supports full-length 32 bit register accesses, so use those exclusively. This
is compatible with SBSAv3, which explicitly requires UART hardware support 32
(and 16 and sometimes 8) bit accesses.
Tested on Juno, Midway, QDF2432, Seattle, and X-Gene 1.
Tested-by: Mark Langsdorf <mlangsdo@redhat.com> Tested-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Christopher Covington <cov@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1cf6e8fc8341 ("tty/serial: at91: fix RTS line management when
hardware handshake is enabled") actually allowed to enable hardware
handshaking.
Before, the CRTSCTS flags was silently ignored.
As the DMA controller can't drive RTS (as explain in the commit message).
Ensure that hardware flow control stays disabled when DMA is used and FIFOs
are not available.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Fixes: 1cf6e8fc8341 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled") Cc: stable <stable@vger.kernel.org> # v4.0+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Müller [Wed, 27 Apr 2016 09:58:32 +0000 (11:58 +0200)]
serial: 8250_pci: fix divide error bug if baud rate is 0
Since commit 21947ba654a6 ("serial: 8250_pci: replace switch-case by
formula"), the 8250 driver crashes in the byt_set_termios() function
with a divide error. This is caused by the fact that a baud rate of 0 (B0)
is not handled properly. Fix it by falling back to B9600 in this case.
Signed-off-by: David Müller <d.mueller@elsoft.ch> Fixes: 21947ba654a6 ("serial: 8250_pci: replace switch-case by formula") Cc: stable@vger.kernel.org Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal fixes from Eduardo Valentin:
"Specifics in this pull request:
- Fixes in mediatek and OF thermal drivers
- Fixes in power_allocator governor
- More fixes of unsigned to int type change in thermal_core.c.
These change have been CI tested using KernelCI bot. \o/"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: fix Mediatek thermal controller build
thermal: consistently use int for trip temp
thermal: fix mtk_thermal build dependency
thermal: minor mtk_thermal.c cleanups
thermal: power_allocator: req_range multiplication should be a 64 bit type
thermal: of: add __init attribute
Merge tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic update from Arnd Bergmann:
"Here is one patch to wire up the preadv/pwritev system calls in the
generic system call table, which is required for all architectures
that were merged in the last few years, including arm64.
Usually these get merged along with the syscall implementation or one
of the architecture trees, but this time that did not happen.
Andre and Christoph both sent a version of this patch, I picked the
one I got first"
* tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
generic syscalls: wire up preadv2 and pwritev2 syscalls
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes: two EDAC driver fixes, a Xen crash fix, a HyperV log spam
fix and a documentation fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86 EDAC, sb_edac.c: Take account of channel hashing when needed
x86 EDAC, sb_edac.c: Repair damage introduced when "fixing" channel address
x86/mm/xen: Suppress hugetlbfs in PV guests
x86/doc: Correct limits in Documentation/x86/x86_64/mm.txt
x86/hyperv: Avoid reporting bogus NMI status for Gen2 instances
Merge branches 'perf-urgent-for-linus', 'smp-urgent-for-linus' and 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf, cpu hotplug and timer fixes from Ingo Molnar:
"perf:
- A single tooling fix for a user-triggerable segfault.
CPU hotplug:
- Fix a CPU hotplug corner case regression, introduced by the recent
hotplug rework
timers:
- Fix a boot hang in the ARM based Tango SoC clocksource driver"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf intel-pt: Fix segfault tracing transactions
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu/hotplug: Fix rollback during error-out in __cpu_disable()
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/tango-xtal: Fix boot hang due to incorrect test
Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"Misc fixes:
pvqspinlocks:
- an instrumentation fix
futexes:
- preempt-count vs pagefault_disable decouple corner case fix
- futex requeue plist race window fix
- futex UNLOCK_PI transaction fix for a corner case"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
asm-generic/futex: Re-enable preemption in futex_atomic_cmpxchg_inatomic()
futex: Acknowledge a new waiter in counter before plist
futex: Handle unlock_pi race gracefully
locking/pvqspinlock: Fix division by zero in qstat_read()
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"A core irq affinity masks related fix and a MIPS irqchip driver fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mips-gic: Don't overrun pcpu_masks array
genirq: Dont allow affinity mask to be updated on IPIs
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool fixes from Ingo Molnar:
"A handful of objtool fixes: two improvements to how warnings are
printed plus a false positive warning fix, and build environment fix"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix Makefile to properly see if libelf is supported
objtool: Detect falling through to the next function
objtool: Add workaround for GCC switch jump table bug
Merge tag 'usb-4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY driver fixes from Greg KH:
"Here are two small sets of patches, both from subsystem trees, USB
gadget and PHY drivers.
Full details are in the shortlog, and they have all been in linux-next
for a while (before I merged them to the USB tree)"
* tag 'usb-4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: gadget: f_fs: Fix use-after-free
usb: dwc3: gadget: Fix suspend/resume during device mode
usb: dwc3: fix memory leak of dwc->regset
usb: dwc3: core: fix PHY handling during suspend
usb: dwc3: omap: fix up error path on probe()
usb: gadget: composite: Clear reserved fields of SSP Dev Cap
phy: rockchip-emmc: adapt binding to specifiy register offset and length
phy: rockchip-emmc: should be a child device of the GRF
phy: rockchip-dp: should be a child device of the GRF
Merge tag 'tty-4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial fixes from Greg KH:
"Here are 3 serial driver fixes for issues that have been reported.
Two are reverts, fixing problems that were in the big TTY/Serial
driver merge in 4.6-rc1, and the last one is a simple bugfix for a
regression that showed up in 4.6-rc1 as well.
All have been in linux-next with no reported issues"
* tag 'tty-4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: 8250: Add hardware dependency to RT288X option"
tty/serial/8250: fix RS485 half-duplex RX
Revert "serial-uartlite: Constify uartlite_be/uartlite_le"
Merge tag 'pinctrl-v4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Some pin control driver fixes came in. One headed for stable and the
other two are just ordinary merge window fixes.
- Make the i.MX driver select REGMAP as a dependency
- Fix up the Mediatek debounce time unit
- Fix a real hairy ffs vs __ffs issue in the Single pinctrl driver"
* tag 'pinctrl-v4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: single: Fix pcs_parse_bits_in_pinctrl_entry to use __ffs than ffs
pinctrl: mediatek: correct debounce time unit in mtk_gpio_set_debounce
pinctrl: imx: Kconfig: PINCTRL_IMX select REGMAP
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Cache invalidation fix for early CPU boot status update (incorrect
cacheline)
- of_put_node() missing in the spin_table code
- EL1/El2 early init inconsistency when Virtualisation Host Extensions
are present
- RCU warning fix in the arm_pmu.c driver
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix EL1/EL2 early init inconsistencies with VHE
drivers/perf: arm-pmu: fix RCU usage on pmu resume from low-power
arm64: spin-table: add missing of_node_put()
arm64: fix invalidation of wrong __early_cpu_boot_status cacheline
Merge tag 'powerpc-4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Three powerpc cpu feature fixes from Anton Blanchard:
- scan_features() updated incorrect bits for REAL_LE
- update cpu_user_features2 in scan_features()
- update TM user feature bits in scan_features()"
* tag 'powerpc-4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Update TM user feature bits in scan_features()
powerpc: Update cpu_user_features2 in scan_features()
powerpc: scan_features() updates incorrect bits for REAL_LE
Merge tag 'iommu-fixes-v4.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"The fixes include:
- Two patches to revert the use of default domains in the ARM SMMU
driver. Enabling this caused regressions which need more thorough
fixing. So the regressions are fixed for now by disabling the use
of default domains.
- A fix for a v4.4 regression in the AMD IOMMU driver which broke
devices behind invisible PCIe-to-PCI bridges with IOMMU enabled"
* tag 'iommu-fixes-v4.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/arm-smmu: Don't allocate resources for bypass domains
iommu/arm-smmu: Fix stream-match conflict with IOMMU_DOMAIN_DMA
iommu/amd: Fix checking of pci dma aliases
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"i915, nouveau and amdgpu/radeon fixes in this:
nouveau:
Two fixes, one for a regression with dithering and one for a bug
hit by the userspace drivers.
i915:
A few fixes, mostly things heading for stable, two important
skylake GT3/4 hangs.
radeon/amdgpu:
Some audio, suspend/resume and some runtime PM fixes, along with
two patches to harden the userptr ABI a bit"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (24 commits)
drm: Loongson-3 doesn't fully support wc memory
drm/nouveau/gr/gf100: select a stream master to fixup tfb offset queries
amdgpu/uvd: add uvd fw version for amdgpu
drm/amdgpu: forbid mapping of userptr bo through radeon device file
drm/radeon: forbid mapping of userptr bo through radeon device file
drm/amdgpu: bump the afmt limit for CZ, ST, Polaris
drm/amdgpu: use defines for CRTCs and AMFT blocks
drm/dp/mst: Validate port in drm_dp_payload_send_msg()
drm/nouveau/kms: fix setting of default values for dithering properties
drm/radeon: print a message if ATPX dGPU power control is missing
Revert "drm/radeon: disable runtime pm on PX laptops without dGPU power control"
drm/amdgpu/acp: fix resume on CZ systems with AZ audio
drm/radeon: add a quirk for a XFX R9 270X
drm/radeon: print pci revision as well as pci ids on driver load
drm/i915: Use fw_domains_put_with_fifo() on HSW
drm/i915: Force ringbuffers to not be at offset 0
drm/i915: Adjust size of PIPE_CONTROL used for gen8 render seqno write
drm/i915/skl: Fix spurious gpu hang with gt3/gt4 revs
drm/i915/skl: Fix rc6 based gpu/system hang
drm/i915/userptr: Hold mmref whilst calling get-user-pages
...
Merge tag 'sound-4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Again a relatively calm week without surprise: most of fixes are about
HD-audio, including fixes for Cirrus codec regression and a race over
regmap access. Although both change are slightly unintuitive, the
risk of further breakage is quite low, I hope.
Other than that, all the rest are trivial"
* tag 'sound-4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix possible race on regmap bypass flip
ALSA: pcxhr: Fix missing mutex unlock
ALSA: hda - add PCI ID for Intel Broxton-T
ALSA: hda - Keep powering up ADCs on Cirrus codecs
ALSA: hda/realtek - Add ALC3234 headset mode for Optiplex 9020m
ALSA - hda: hdmi check NULL pointer in hdmi_set_chmap
ALSA: hda - Don't trust the reported actual power state
Tony Luck [Thu, 14 Apr 2016 17:21:52 +0000 (10:21 -0700)]
x86 EDAC, sb_edac.c: Repair damage introduced when "fixing" channel address
In commit:
eb1af3b71f9d ("Fix computation of channel address")
I switched the "sck_way" variable from holding the log2 value read
from the h/w to instead be the actual number. Unfortunately it
is needed in log2 form when used to shift the address.
Tested-by: Patrick Geary <patrickg@supermicro.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Aristeu Rozanski <arozansk@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-edac@vger.kernel.org Cc: stable@vger.kernel.org Fixes: eb1af3b71f9d ("Fix computation of channel address") Signed-off-by: Ingo Molnar <mingo@kernel.org>
Merge tag 'fixes-for-v4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.6-rc5
No more major fixes left. Out of the 6 fixes we have
here, 4 are on dwc3.
The most important is the memory leak fix in
dwc3/debugfs.c. We also have a fix for PHY handling
in suspend/resume and a fix for dwc3-omap's error
handling.
Suspend/resume also had the potential to trigger a
NULL pointer dereference on dwc3; that's also fixed
now.
Our good ol' ffs function gets a use-after-free fix
while the generic composite.c layer has a robustness
fix by making sure reserved fields of a possible SSP
device capability descriptor is cleared to 0.
Jan Beulich [Thu, 21 Apr 2016 06:27:04 +0000 (00:27 -0600)]
x86/mm/xen: Suppress hugetlbfs in PV guests
Huge pages are not normally available to PV guests. Not suppressing
hugetlbfs use results in an endless loop of page faults when user mode
code tries to access a hugetlbfs mapped area (since the hypervisor
denies such PTEs to be created, but error indications can't be
propagated out of xen_set_pte_at(), just like for various of its
siblings), and - once killed in an oops like this:
cpu/hotplug: Fix rollback during error-out in __cpu_disable()
The recent introduction of the hotplug thread which invokes the callbacks on
the plugged cpu, cased the following regression:
If takedown_cpu() fails, then we run into several issues:
1) The rollback of the target cpu states is not invoked. That leaves the smp
threads and the hotplug thread in disabled state.
2) notify_online() is executed due to a missing skip_onerr flag. That causes
that both CPU_DOWN_FAILED and CPU_ONLINE notifications are invoked which
confuses quite some notifiers.
3) The CPU_DOWN_FAILED notification is not invoked on the target CPU. That's
not an issue per se, but it is inconsistent and in consequence blocks the
patches which rely on these states being invoked on the target CPU and not
on the controlling cpu. It also does not preserve the strict call order on
rollback which is problematic for the ongoing state machine conversion as
well.
To fix this we add a rollback flag to the remote callback machinery and invoke
the rollback including the CPU_DOWN_FAILED notification on the remote
cpu. Further mark the notify online state with 'skip_onerr' so we don't get a
double invokation.
This workaround will go away once we moved the unplug invocation to the target
cpu itself.
[ tglx: Massaged changelog and moved the CPU_DOWN_FAILED notifiaction to the
target cpu ]
Fixes: 4cb28ced23c4 ("cpu/hotplug: Create hotplug threads") Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: linux-s390@vger.kernel.org Cc: rt@linutronix.de Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Anna-Maria Gleixner <anna-maria@linutronix.de> Link: http://lkml.kernel.org/r/20160408124015.GA21960@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Daniel Lezcano [Tue, 19 Apr 2016 13:43:02 +0000 (15:43 +0200)]
clocksource/drivers/tango-xtal: Fix boot hang due to incorrect test
Commit 0881841f7e78 introduced a regression by inverting a test check
after calling clocksource_mmio_init(). That results on the system to
hang at boot time.
Fix it by inverting the test again.
Fixes: 0881841f7e78 ("Replace code by clocksource_mmio_init") Reported-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Steven Rostedt [Wed, 20 Apr 2016 15:32:35 +0000 (11:32 -0400)]
objtool: Fix Makefile to properly see if libelf is supported
When doing a make allmodconfig, I hit the following compile error:
In file included from builtin-check.c:32:0:
elf.h:22:18: fatal error: gelf.h: No such file or directory
compilation terminated.
...
Digging into it, it appears that the $(shell ..) command in the Makefile does
not give the proper result when it fails to find -lelf, and continues to
compile objtool.
Instead, use the "try-run" makefile macro to perform the test. This gives a
proper result for both cases.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Acked-by: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Bernd Petrovitsch <bernd@petrovitsch.priv.at> Cc: Borislav Petkov <bp@alien8.de> Cc: Chris J Arges <chris.j.arges@canonical.com> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michal Marek <mmarek@suse.cz> Cc: Namhyung Kim <namhyung@gmail.com> Cc: Pedro Alves <palves@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: live-patching@vger.kernel.org Fixes: 442f04c34a1a4 ("objtool: Add tool to perform compile-time stack metadata validation") Link: http://lkml.kernel.org/r/20160420153234.GA24032@home.goodmis.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Airlie [Fri, 22 Apr 2016 00:39:26 +0000 (10:39 +1000)]
Merge branch 'drm-fixes-4.6' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Misc radeon and amdgpu bug fixes for 4.6.
* 'drm-fixes-4.6' of git://people.freedesktop.org/~agd5f/linux:
amdgpu/uvd: add uvd fw version for amdgpu
drm/amdgpu: forbid mapping of userptr bo through radeon device file
drm/radeon: forbid mapping of userptr bo through radeon device file
drm/amdgpu: bump the afmt limit for CZ, ST, Polaris
drm/amdgpu: use defines for CRTCs and AMFT blocks
drm/radeon: print a message if ATPX dGPU power control is missing
Revert "drm/radeon: disable runtime pm on PX laptops without dGPU power control"
drm/amdgpu/acp: fix resume on CZ systems with AZ audio
drm/radeon: add a quirk for a XFX R9 270X
drm/radeon: print pci revision as well as pci ids on driver load
drm/amdgpu: when suspending, if uvd/vce was running. need to cancel delay work.
drm/radeon: fix initial connector audio value
projects / linux-beck.git / log