This change adds in the USB product ID for the Gyration
GYR4101US USB media center remote control. This remote
is similar enough to the other two devices that this driver
can be used without any other changes to get full support
for the remote.
BugLink: https://launchpad.net/bugs/551949
Symptom: On the reporter's Shuttle device, using PulseAudio in Ubuntu
10.04 LTS results in "popping clicking" audio with the PA crashing
shortly thereafter.
Test case: Using Ubuntu 10.04 LTS (Linux 2.6.32.12), Linux 2.6.33, or
Linux 2.6.34, adjust the HDA device's volume with PulseAudio.
Resolution: add SSID for this machine to the position_fix quirk table,
explicitly specifying the LPIB method.
Reported-and-Tested-By: Christian Mehlis <mehlis@inf.fu-berlin.de> Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/586347
Symptom: On the Sony VPCS11V9E, using GStreamer-based applications with
PulseAudio in Ubuntu 10.04 LTS results in stuttering audio. It appears
to worsen with increased I/O.
Test case: use Rhythmbox under increased I/O pressure. This symptom is
reproducible in the current daily stable alsa-driver snapshots (at least
up until 21 May 2010; later snapshots fail to build from source due to
missing preprocessor directives when compiled against 2.6.32).
Resolution: add SSID for this machine to the position_fix quirk table,
explicitly specifying the LPIB method.
Reported-and-Tested-By: Lauri Kainulainen <lauri@sokkelo.net> Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/583983
Symptom: on a significant number of hardware, booting from a live cd
results in capture working correctly, but once the distribution is
installed, booting from the install results in capture not working.
Test case: boot from Ubuntu 10.04 LTS live cd; capture works correctly.
Install to HD and reboot; capture does not work. Reproduced with 2.6.32
mainline build (vanilla kernel.org compile).
Resolution: add SSID for Acer Aspire 5110 to the position_fix quirk
table, explicitly specifying the LPIB method.
I'll be sending additional patches for these SSIDs as bug reports are
confirmed.
Reported-and-Tested-By: Leo Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/549560
Symptom: on a significant number of hardware, booting from a live cd
results in capture working correctly, but once the distribution is
installed, booting from the install results in capture not working.
Test case: boot from Ubuntu 10.04 LTS live cd; capture works correctly.
Install to HD and reboot; capture does not work. Reproduced with 2.6.32
mainline build (vanilla kernel.org compile)
Resolution: add SSID for Toshiba A100-259 to the position_fix quirk
table, explicitly specifying the LPIB method.
I'll be sending additional patches for these SSIDs as bug reports are
confirmed.
This patch also trivially sorts the quirk table in ascending order by
subsystem vendor.
Reported-and-Tested-by: <davide.molteni@gmail.com> Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/576160
Symptom: Currently (2.6.32.12) the Dell M1730 uses the 3stack model
quirk. Unfortunately this means that capture is not functional out-
of-the-box despite ensuring that capture settings are unmuted and
raised fully.
Test case: boot from Ubuntu 10.04 LTS live cd; capture does not
work.
Resolution: Correct the model quirk for Dell M1730 to rely on the
BIOS configuration.
This patch also trivially sorts the quirk into the correct section
based on the comments.
Commit 7910b4a1db63fefc3d291853d33c34c5b6352e8e in 2.6.34 changed the
runtime->boundary calculation to make this value a multiple of both the
buffer_size and the period_size, because the latter is assumed by the
runtime->hw_ptr_interrupt calculation.
However, due to the lack of a ioctl that could read the software
parameters before they are set, the kernel requires that alsa-lib
calculates the boundary value, too. The changed algorithm leads to
a different boundary value used by alsa-lib, which makes, e.g., mplayer
fail to play a 44.1 kHz file because the silence_size parameter is now
invalid; bug report:
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=5015>.
This patch reverts the change to the boundary calculation, and instead
fixes the hw_ptr_interrupt calculation to be period-aligned regardless
of the boundary value.
In the cleanup of the hw_ptr update functions in 2.6.33, the calculation
of the delta value was changed to use the modulo operator to protect
against a negative difference due to the pointer wrapping around at the
boundary.
However, the ptr variables are unsigned, so a negative difference would
result in the two complement's value which has no relation to the actual
difference relative to the boundary; the result is typically some value
near LONG_MAX-boundary. Furthermore, even if the modulo operation would
be done with signed types, the result of a negative dividend could be
negative.
The invalid delta value is then caught by the following checks, but this
means that the pointer update is ignored.
To fix this, use a range check as in the other pointer calculations.
Currently, we can hit a nasty case with optimistic
spinning on mutexes:
CPU A tries to take a mutex, while holding the BKL
CPU B tried to take the BLK while holding the mutex
This looks like a AB-BA scenario but in practice, is
allowed and happens due to the auto-release on
schedule() nature of the BKL.
In that case, the optimistic spinning code can get us
into a situation where instead of going to sleep, A
will spin waiting for B who is spinning waiting for
A, and the only way out of that loop is the
need_resched() test in mutex_spin_on_owner().
This patch fixes it by completely disabling spinning
if we own the BKL. This adds one more detail to the
extensive list of reasons why it's a bad idea for
kernel code to be holding the BKL.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
LKML-Reference: <20100519054636.GC12389@ozlabs.org>
[ added an unlikely() attribute to the branch ] Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the seqno for a vis packet had a wrap around from i.e. 255 to 0,
add_packet() would falsely claim the older packet with the seqno 255 as
newer as the one with the seqno of 0 and would therefore ignore the new
packet. This happens with all following vis packets until the old vis
packet expires after 180 seconds timeout. This patch fixes this issue
and gets rid of these highly undesired 3min. breaks for the vis-server.
Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
TQ and HNA records for originators on secondary interfaces were
wrongly being included on the primary interface. Ensure we output a
line for each source interface on every node, so we correctly separate
primary and secondary interface records.
send_vis_packets() would disable interrupts before calling
dev_queue_xmit() which resulting in a backtrace in local_bh_enable().
Fix this by using kref on the vis_info object so that we can call
send_vis_packets() without holding vis_hash_lock. vis_hash_lock also
used to protect recv_list, so we now need a new lock to protect that
instead of vis_hash_lock.
Also a few checkpatch cleanups.
Reported-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In http://bugzilla.novell.com/show_bug.cgi?id=597299, the vt6655 driver
generates a kernel BUG on a NULL pointer dereference at NULL. This problem
has been traced to a failure in the wpa_set_wpadev() routine. As the vt6656
driver does not call this routine, the vt6655 code is similarly set to skip
the call.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Tested-by: Richard Meek <osl2008@googlemail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The SH SOHARD ARCNET cards are implemented using generic PLX Technology
PCI<->IOBus bridges. Subvendor and subdevice IDs were not specified,
causing the driver to attach to any such bridge and likely crash the
system by attempting to initialize an unrelated device.
Fix by specifying subvendor and subdevice according to the values found
in the PCI-ID Repository at http://pci-ids.ucw.cz/ .
Signed-off-by: Andreas Bombe <aeb@debian.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the second attempt to fix the problem whereby a COMMIT call
causes a lease break and triggers a possible deadlock.
The problem is that nfsd attempts to break a lease on a COMMIT call.
This triggers a delegation recall if the lease is held for a delegation.
If the client is the one holding the delegation and it's the same one on
which it's issuing the COMMIT, then it can't return that delegation
until the COMMIT is complete. But, nfsd won't complete the COMMIT until
the delegation is returned. The client and server are essentially
deadlocked until the state is marked bad (due to the client not
responding on the callback channel).
The first patch attempted to deal with this by eliminating the open of
the file altogether and simply had nfsd_commit pass a NULL file pointer
to the vfs_fsync_range. That would conflict with some work in progress
by Christoph Hellwig to clean up the fsync interface, so this patch
takes a different approach.
This declares a new NFSD_MAY_NOT_BREAK_LEASE access flag that indicates
to nfsd_open that it should not break any leases when opening the file,
and has nfsd_commit set that flag on the nfsd_open call.
For now, this patch leaves nfsd_commit opening the file with write
access since I'm not clear on what sort of access would be more
appropriate.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The /proc/fs/nfsd/versions file calls nfsd_vers() to check whether
the particular nfsd version is present/available. The problem is
that once I turn off e.g. NFSD-V4 this call returns -1 which is
true from the callers POV which is wrong.
The proposal is to report false in that case.
The bug has existed since 6658d3a7bbfd1768 "[PATCH] knfsd: remove
nfsd_versbits as intermediate storage for desired versions".
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Acked-by: NeilBrown <neilb@suse.de> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit a45185d2d "cpumask: convert kernel/compat.c" broke libnuma, which
abuses sched_getaffinity to find out NR_CPUS in order to parse
/sys/devices/system/node/node*/cpumap.
On NUMA systems with less than 32 possibly CPUs, the current
compat_sys_sched_getaffinity now returns '4' instead of the actual
NR_CPUS/8, which makes libnuma bail out when parsing the cpumap.
The libnuma call sched_getaffinity(0, bitmap, 4096) at first. It mean
the libnuma expect the return value of sched_getaffinity() is either len
argument or NR_CPUS. But it doesn't expect to return nr_cpu_ids.
Strictly speaking, userland requirement are
1) Glibc assume the return value mean the lengh of initialized
of mask argument. E.g. if sched_getaffinity(1024) return 128,
glibc make zero fill rest 896 byte.
2) Libnuma assume the return value can be used to guess NR_CPUS
in kernel. It assume len-arg<NR_CPUS makes -EINVAL. But
it try len=4096 at first and 4096 is always bigger than
NR_CPUS. Then, if we remove strange min_length normalization,
we never hit -EINVAL case.
sched_getaffinity() already solved this issue. This patch adapts
compat_sys_sched_getaffinity() to match the non-compat case.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Acked-by: Rusty Russell <rusty@rustcorp.com.au> Acked-by: Arnd Bergmann <arnd@arndb.de> Reported-by: Ken Werner <ken.werner@web.de> Cc: Andi Kleen <andi@firstfloor.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
page_mapping() check this via VM_BUG_ON(PageSlab(page)) so we bug here
with the according debuging turned on.
Future TODO: replace this with a flush_dcache_page_for_pio() API
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are ATAPI devices which raise AN when hit by commands issued by
open(). This leads to infinite loop of AN -> MEDIA_CHANGE uevent ->
udev open() to check media -> AN.
Both ACS and SerialATA standards don't define in which case ATAPI
devices are supposed to raise or not raise AN. They both list media
insertion event as a possible use case for ATAPI ANs but there is no
clear description of what constitutes such events. As such, it seems
a bit too naive to export ANs directly to userland as MEDIA_CHANGE
events without further verification (which should behave similarly to
windows as it apparently is the only thing that some hardware vendors
are testing against).
This patch adds libata.atapi_an module parameter and disables ATAPI AN
by default for now.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Kay Sievers <kay.sievers@vrfy.org> Cc: Nick Bowler <nbowler@elliptictech.com> Cc: David Zeuthen <david@fubar.dk> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In particular, before this patch, the command
ls -l
in an NFS mounted directory would always check if the directory on the server
had changed and if so would flush and refill the pagecache for the dir.
After this patch, the same "ls -l" will repeatedly return stale date until
the cached attributes for the directory time out.
The following patch fixes this by ensuring the d_revalidate is called by
do_last when "." is being looked-up.
link_path_walk has already called d_revalidate, but in that case LOOKUP_OPEN
is not set so nfs_lookup_verify_inode chooses not to do any validation.
The following patch restores the original behaviour.
once anon_inode_getfd() is called, you can't expect *anything* about
struct file that descriptor points to - another thread might be doing
whatever it likes with descriptor table at that point.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Before this patch this message would very briefly appear on the
screen and then the screen would get updates only on the top,
for number of interrupts received, etc, but no annotation would
be performed:
[root@doppio linux-2.6-tip]# perf top -s n_tty_write > /tmp/bla
objdump: '[kernel.kallsyms]': No such file
Now this is what the user gets:
[root@doppio linux-2.6-tip]# perf top -s n_tty_write
Can't annotate n_tty_write: No vmlinux file was found in the
path: [0] vmlinux
[1] /boot/vmlinux
[2] /boot/vmlinux-2.6.33-rc5
[3] /lib/modules/2.6.33-rc5/build/vmlinux
[4] /usr/lib/debug/lib/modules/2.6.33-rc5/vmlinux
[root@doppio linux-2.6-tip]#
This bug was introduced when we added automatic search for
vmlinux, before that time the user had to specify a vmlinux
file.
Reported-by: David S. Miller <davem@davemloft.net> Reported-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Frédéric Weisbecker <fweisbec@gmail.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1268664418-28328-2-git-send-email-acme@infradead.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Both Stephane and Corey reported that PERF_FORMAT_GROUP didn't
work as expected if the task the counters were attached to quit
before the read() call.
The cause is that we unconditionally destroy the grouping when
we remove counters from their context. Fix this by splitting off
the group destroy from the list removal such that
perf_event_remove_from_context() does not do this and change
perf_event_release() to do so.
Parsing an option from the command line with OPT_BOOLEAN on a
bool data type would not work on a big-endian machine due to the
manner in which the boolean was being cast into an int and
incremented. For example, running 'perf probe --list' on a
PowerPC machine would fail to properly set the list_events bool
and would therefore print out the usage information and
terminate.
This patch makes OPT_BOOLEAN work as expected with a bool
datatype. For cases where the original OPT_BOOLEAN was
intentionally being used to increment an int each time it was
passed in on the command line, this patch introduces OPT_INCR
with the old behaviour of OPT_BOOLEAN (the verbose variable is
currently the only such example of this).
I have reviewed every use of OPT_BOOLEAN to verify that a true
C99 bool was passed. Where integers were used, I verified that
they were only being used for boolean logic and changed them to
bools to ensure that they would not be mistakenly used as ints.
The major exception was the verbose variable which now uses
OPT_INCR instead of OPT_BOOLEAN.
Signed-off-by: Ian Munsie <imunsie@au.ibm.com> Acked-by: David S. Miller <davem@davemloft.net> Cc: <stable@kernel.org> Cc: Git development list <git@vger.kernel.org> Cc: Ian Munsie <imunsie@au1.ibm.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Paul Mackerras <paulus@samba.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Eric B Munson <ebmunson@us.ibm.com> Cc: Valdis.Kletnieks@vt.edu Cc: WANG Cong <amwang@redhat.com> Cc: Thiago Farina <tfransosi@gmail.com> Cc: Masami Hiramatsu <mhiramat@redhat.com> Cc: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com> Cc: Jaswinder Singh Rajput <jaswinderrajput@gmail.com> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Cc: Mike Galbraith <efault@gmx.de> Cc: Tom Zanussi <tzanussi@gmail.com> Cc: Anton Blanchard <anton@samba.org> Cc: John Kacur <jkacur@redhat.com> Cc: Li Zefan <lizf@cn.fujitsu.com> Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <1271147857-11604-1-git-send-email-imunsie@au.ibm.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
oprofile used a double buffer scheme for its cpu event buffer
to avoid races on reading with the old locked ring buffer.
But that is obsolete now with the new ring buffer, so simply
use a single buffer. This greatly simplifies the code and avoids
a lot of sample drops on large runs, especially with call graph.
Based on suggestions from Steven Rostedt
For stable kernels from v2.6.32, but not earlier.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Robert Richter <robert.richter@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
rtnetlink: make SR-IOV VF interface symmetric
sctp: delete active ICMP proto unreachable timer when free transport
tcp: fix MD5 (RFC2385) support
Linus Torvalds [Sun, 16 May 2010 18:11:31 +0000 (11:11 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Oprofile: Fix Loongson irq handler
MIPS: N32: Use compat version for sys_ppoll.
MIPS FPU emulator: allow Cause bits of FCSR to be writeable by ctc1
Wei Yongjun [Sun, 9 May 2010 16:56:07 +0000 (16:56 +0000)]
sctp: delete active ICMP proto unreachable timer when free transport
transport may be free before ICMP proto unreachable timer expire, so
we should delete active ICMP proto unreachable timer when transport
is going away.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 16 May 2010 07:34:04 +0000 (00:34 -0700)]
tcp: fix MD5 (RFC2385) support
TCP MD5 support uses percpu data for temporary storage. It currently
disables preemption so that same storage cannot be reclaimed by another
thread on same cpu.
We also have to make sure a softirq handler wont try to use also same
context. Various bug reports demonstrated corruptions.
Fix is to disable preemption and BH.
Reported-by: Bhaskar Dutta <bhaskie@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wu Zhangjin [Thu, 6 May 2010 16:59:46 +0000 (00:59 +0800)]
MIPS: Oprofile: Fix Loongson irq handler
The interrupt enable bit for the performance counters is in the Control
Register $24, not in the counter register.
loongson2_perfcount_handler(), we need to use
Shane McDonald [Fri, 7 May 2010 05:26:57 +0000 (23:26 -0600)]
MIPS FPU emulator: allow Cause bits of FCSR to be writeable by ctc1
In the FPU emulator code of the MIPS, the Cause bits of the FCSR register
are not currently writeable by the ctc1 instruction. In odd corner cases,
this can cause problems. For example, a case existed where a divide-by-zero
exception was generated by the FPU, and the signal handler attempted to
restore the FPU registers to their state before the exception occurred. In
this particular setup, writing the old value to the FCSR register would
cause another divide-by-zero exception to occur immediately. The solution
is to change the ctc1 instruction emulator code to allow the Cause bits of
the FCSR register to be writeable. This is the behaviour of the hardware
that the code is emulating.
This problem was found by Shane McDonald, but the credit for the fix goes
to Kevin Kissell. In Kevin's words:
I submit that the bug is indeed in that ctc_op: case of the emulator. The
Cause bits (17:12) are supposed to be writable by that instruction, but the
CTC1 emulation won't let them be updated by the instruction. I think that
actually if you just completely removed lines 387-388 [...] things would
work a good deal better. At least, it would be a more accurate emulation of
the architecturally defined FPU. If I wanted to be really, really pedantic
(which I sometimes do), I'd also protect the reserved bits that aren't
necessarily writable.
Signed-off-by: Shane McDonald <mcdonald.shane@gmail.com>
To: anemo@mba.ocn.ne.jp
To: kevink@paralogos.com
To: sshtylyov@mvista.com
Patchwork: http://patchwork.linux-mips.org/patch/1205/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
Nicolas Ferre [Sat, 15 May 2010 16:32:31 +0000 (12:32 -0400)]
mmc: at91_mci: modify cache flush routines
As we were using an internal dma flushing routine, this patch changes to
the DMA API flush_kernel_dcache_page(). Driver is able to compile now.
[akpm@linux-foundation.org: flush_kernel_dcache_page() comes before kunmap_atomic()] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 15 May 2010 16:03:15 +0000 (09:03 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
JFS: Free sbi memory in error path
fs/sysv: dereferencing ERR_PTR()
Fix double-free in logfs
Fix the regression created by "set S_DEAD on unlink()..." commit
Linus Torvalds [Sat, 15 May 2010 16:03:02 +0000 (09:03 -0700)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf record: Add a fallback to the reference relocation symbol
Jan Blunck [Mon, 12 Apr 2010 23:44:08 +0000 (16:44 -0700)]
JFS: Free sbi memory in error path
I spotted the missing kfree() while removing the BKL.
[akpm@linux-foundation.org: avoid multiple returns so it doesn't happen again] Signed-off-by: Jan Blunck <jblunck@suse.de> Cc: Dave Kleikamp <shaggy@austin.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Fri, 30 Apr 2010 21:17:09 +0000 (17:17 -0400)]
Fix the regression created by "set S_DEAD on unlink()..." commit
1) i_flags simply doesn't work for mount/unlink race prevention;
we may have many links to file and rm on one of those obviously
shouldn't prevent bind on top of another later on. To fix it
right way we need to mark _dentry_ as unsuitable for mounting
upon; new flag (DCACHE_CANT_MOUNT) is protected by d_flags and
i_mutex on the inode in question. Set it (with dont_mount(dentry))
in unlink/rmdir/etc., check (with cant_mount(dentry)) in places
in namespace.c that used to check for S_DEAD. Setting S_DEAD
is still needed in places where we used to set it (for directories
getting killed), since we rely on it for readdir/rmdir race
prevention.
2) rename()/mount() protection has another bogosity - we unhash
the target before we'd checked that it's not a mountpoint. Fixed.
3) ancient bogosity in pivot_root() - we locked i_mutex on the
right directory, but checked S_DEAD on the different (and wrong)
one. Noticed and fixed.
Linus Torvalds [Sat, 15 May 2010 04:28:42 +0000 (21:28 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6126/1: ARM mpcore_wdt: fix build failure and other fixes
ARM: 6125/1: ARM TWD: move TWD registers to common header
ARM: 6110/1: Fix Thumb-2 kernel builds when UACCESS_WITH_MEMCPY is enabled
ARM: 6112/1: Use the Inner Shareable I-cache and BTB ops on ARMv7 SMP
ARM: 6111/1: Implement read/write for ownership in the ARMv6 DMA cache ops
ARM: 6106/1: Implement copy_to_user_page() for noMMU
ARM: 6105/1: Fix the __arm_ioremap_caller() definition in nommu.c
Hugh Dickins [Sat, 15 May 2010 02:44:10 +0000 (19:44 -0700)]
profile: fix stats and data leakage
If the kernel is large or the profiling step small, /proc/profile
leaks data and readprofile shows silly stats, until readprofile -r
has reset the buffer: clear the prof_buffer when it is vmalloc()ed.
H. Peter Anvin [Fri, 14 May 2010 20:55:57 +0000 (13:55 -0700)]
x86, mrst: Don't blindly access extended config space
Do not blindly access extended configuration space unless we actively
know we're on a Moorestown platform. The fixed-size BAR capability
lives in the extended configuration space, and thus is not applicable
if the configuration space isn't appropriately sized.
This fixes booting certain VMware configurations with CONFIG_MRST=y.
Moorestown will add a fake PCI-X 266 capability to advertise the
presence of extended configuration space.
Reported-and-tested-by: Petr Vandrovec <petr@vandrovec.name> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Acked-by: Jacob Pan <jacob.jun.pan@intel.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <AANLkTiltKUa3TrKR1M51eGw8FLNoQJSLT0k0_K5X3-OJ@mail.gmail.com>
Linus Torvalds [Fri, 14 May 2010 19:20:09 +0000 (12:20 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, cacheinfo: Turn off L3 cache index disable feature in virtualized environments
x86, k8: Fix build error when K8_NB is disabled
x86, amd: Check X86_FEATURE_OSVW bit before accessing OSVW MSRs
x86: Fix fake apicid to node mapping for numa emulation
The L3 cache index disable feature of AMD CPUs has to be disabled if the
kernel is running as guest on top of a hypervisor because northbridge
devices are not available to the guest. Currently, this fixes a boot
crash on top of Xen. In the future this will become an issue on KVM as
well.
Check if northbridge devices are present and do not enable the feature
if there are none.
[ hpa: backported to 2.6.34 ]
Signed-off-by: Frank Arnold <frank.arnold@amd.com>
LKML-Reference: <1271945222-5283-3-git-send-email-bp@amd64.org> Acked-by: Borislav Petkov <borislav.petkov@amd.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: <stable@kernel.org>
K8_NB depends on PCI and when the last is disabled (allnoconfig) we fail
at the final linking stage due to missing exported num_k8_northbridges.
Add a header stub for that.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <20100503183036.GJ26107@aftab> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: <stable@kernel.org>
Linus Torvalds [Fri, 14 May 2010 18:49:42 +0000 (11:49 -0700)]
Merge branch 'for-linus' of git://git.infradead.org/users/eparis/notify
* 'for-linus' of git://git.infradead.org/users/eparis/notify:
inotify: don't leak user struct on inotify release
inotify: race use after free/double free in inotify inode marks
inotify: clean up the inotify_add_watch out path
Inotify: undefined reference to `anon_inode_getfd'
Manual merge to remove duplicate "select ANON_INODES" from Kconfig file
Sergei Shtylyov [Thu, 13 May 2010 18:51:51 +0000 (22:51 +0400)]
DA830: fix USB 2.0 clock entry
DA8xx OHCI driver fails to load due to failing clk_get() call for the USB 2.0
clock. Arrange matching USB 2.0 clock by the clock name instead of the device.
(Adding another CLK() entry for "ohci.0" device won't do -- in the future I'll
also have to enable USB 2.0 clock to configure CPPI 4.1 module, in which case
I won't have any device at all.)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Pavel Emelyanov [Wed, 12 May 2010 22:34:07 +0000 (15:34 -0700)]
inotify: don't leak user struct on inotify release
inotify_new_group() receives a get_uid-ed user_struct and saves the
reference on group->inotify_data.user. The problem is that free_uid() is
never called on it.
Issue seem to be introduced by 63c882a0 (inotify: reimplement inotify
using fsnotify) after 2.6.30.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Eric Paris <eparis@parisplace.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Eric Paris <eparis@redhat.com>
Eric Paris [Tue, 11 May 2010 21:17:40 +0000 (17:17 -0400)]
inotify: race use after free/double free in inotify inode marks
There is a race in the inotify add/rm watch code. A task can find and
remove a mark which doesn't have all of it's references. This can
result in a use after free/double free situation.
Task A Task B
------------ -----------
inotify_new_watch()
allocate a mark (refcnt == 1)
add it to the idr
inotify_rm_watch()
inotify_remove_from_idr()
fsnotify_put_mark()
refcnt hits 0, free
take reference because we are on idr
[at this point it is a use after free]
[time goes on]
refcnt may hit 0 again, double free
The fix is to take the reference BEFORE the object can be found in the
idr.
Signed-off-by: Eric Paris <eparis@redhat.com> Cc: <stable@kernel.org>
Linus Torvalds [Fri, 14 May 2010 14:29:29 +0000 (07:29 -0700)]
Merge branch 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze
* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Fix module loading on system with WB cache
microblaze: export assembly functions used by modules
microblaze: Remove powerpc code from Microblaze port
microblaze: Remove compilation warnings in cache macro
microblaze: export assembly functions used by modules
microblaze: fix get_user/put_user side-effects
microblaze: re-enable interrupts before calling schedule
Redirecting directly to lsm, here's the patch discussed on lkml:
http://lkml.org/lkml/2010/4/22/219
The mmap_min_addr value is useful information for an admin to see without
being root ("is my system vulnerable to kernel NULL pointer attacks?") and
its setting is trivially easy for an attacker to determine by calling
mmap() in PAGE_SIZE increments starting at 0, so trying to keep it private
has no value.
Only require CAP_SYS_RAWIO if changing the value, not reading it.
Comment from Serge :
Me, I like to write my passwords with light blue pen on dark blue
paper, pasted on my window - if you're going to get my password, you're
gonna get a headache.
Signed-off-by: Kees Cook <kees.cook@canonical.com> Acked-by: Serge Hallyn <serue@us.ibm.com> Signed-off-by: James Morris <jmorris@namei.org>
(cherry picked from commit 822cceec7248013821d655545ea45d1c6a9d15b3)
Linus Torvalds [Thu, 13 May 2010 21:36:19 +0000 (14:36 -0700)]
Merge branch 'kvm-updates/2.6.34' of git://git.kernel.org/pub/scm/virt/kvm/kvm
* 'kvm-updates/2.6.34' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Keep index within boundaries in kvmppc_44x_emul_tlbwe()
KVM: VMX: blocked-by-sti must not defer NMI injections
KVM: x86: Call vcpu_load and vcpu_put in cpuid_update
KVM: SVM: Fix wrong intercept masks on 32 bit
KVM: convert ioapic lock to spinlock
serial: imx.c: fix CTS trigger level lower to avoid lost chars
The imx CTS trigger level is left at its reset value that is 32
chars. Since the RX FIFO has 32 entries, when CTS is raised, the
FIFO already is full. However, some serial port devices first empty
their TX FIFO before stopping when CTS is raised, resulting in lost
chars.
This patch sets the trigger level lower so that other chars arrive
after CTS is raised, there is still room for 16 of them.
Alan Cox [Tue, 4 May 2010 19:42:36 +0000 (20:42 +0100)]
tty: Fix unbalanced BKL handling in error path
Arnd noted:
After the "retry_open:" label, we first get the tty_mutex
and then the BKL. However a the end of tty_open, we jump
back to retry_open with the BKL still held. If we run into
this case, the tty_open function will be left with the BKL
still held.
Jan Kara [Thu, 13 May 2010 10:52:57 +0000 (12:52 +0200)]
vfs: Fix O_NOFOLLOW behavior for paths with trailing slashes
According to specification
mkdir d; ln -s d a; open("a/", O_NOFOLLOW | O_RDONLY)
should return success but currently it returns ELOOP. This is a
regression caused by path lookup cleanup patch series.
Fix the code to ignore O_NOFOLLOW in case the provided path has trailing
slashes.
Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Reported-by: Marius Tolzmann <tolzmann@molgen.mpg.de> Acked-by: Miklos Szeredi <mszeredi@suse.cz> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 13 May 2010 14:35:26 +0000 (07:35 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ice1724 - Fix ESI Maya44 capture source control
ALSA: pcm - Use pgprot_noncached() for MIPS non-coherent archs
ALSA: virtuoso: fix Xonar D1/DX front panel microphone
ALSA: hda - Add hp-dv4 model for IDT 92HD71bx
ALSA: hda - Fix mute-LED GPIO pin for HP dv series
ALSA: hda: Fix 0 dB for Lenovo models using Conexant CX20549 (Venice)
Linus Torvalds [Thu, 13 May 2010 14:28:43 +0000 (07:28 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ad7877 - keep dma rx buffers in seperate cache lines
Input: psmouse - reset all types of mice before reconnecting
Input: elantech - use all 3 bytes when checking version
Input: iforce - fix Guillemot Jet Leader 3D entry
Input: iforce - add Guillemot Jet Leader Force Feedback
Mark Brown [Fri, 2 Apr 2010 12:08:39 +0000 (13:08 +0100)]
mfd: Clean up after WM83xx AUXADC interrupt if it arrives late
In certain circumstances, especially under heavy load, the AUXADC
completion interrupt may be detected after we've timed out waiting for
it. That conversion would still succeed but the next conversion will
see the completion that was signalled by the interrupt for the previous
conversion and therefore not wait for the AUXADC conversion to run,
causing it to report failure.
Provide a simple, non-invasive cleanup by using try_wait_for_completion()
to ensure that the completion is not signalled before we wait. Since
the AUXADC is run within a mutex we know there can only have been at
most one AUXADC interrupt outstanding. A more involved change should
follow for the next merge window.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Michal Simek [Thu, 13 May 2010 08:55:47 +0000 (10:55 +0200)]
microblaze: Remove compilation warnings in cache macro
CC arch/microblaze/kernel/cpu/cache.o
arch/microblaze/kernel/cpu/cache.c: In function '__invalidate_dcache_range_wb':
arch/microblaze/kernel/cpu/cache.c:398: warning: ISO C90 forbids mixed declarations and code
arch/microblaze/kernel/cpu/cache.c: In function '__flush_dcache_range_wb':
arch/microblaze/kernel/cpu/cache.c:509: warning: ISO C90 forbids mixed declara
With dma based spi transmission, data corruption is observed
occasionally. With dma buffers located right next to msg and
xfer fields, cache lines correctly flushed in preparation for
dma usage may be polluted again when writing to fields in the
same cache line.
Make sure cache fields used with dma do not share cache lines
with fields changed during dma handling. As both fields are part
of a struct that is allocated via kzalloc, thus cache aligned,
moving the fields to the 1st position and insert padding for
alignment does the job.
Signed-off-by: Oskar Schirmer <os@emlix.com> Signed-off-by: Daniel Glöckner <dg@emlix.com> Signed-off-by: Oliver Schneidewind <osw@emlix.com> Signed-off-by: Johannes Weiner <jw@emlix.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
[dtor@mail.ru - changed to use ___cacheline_aligned as suggested
by akpm] Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Dmitry Torokhov [Thu, 13 May 2010 07:42:23 +0000 (00:42 -0700)]
Input: psmouse - reset all types of mice before reconnecting
Synaptics hardware requires resetting device after suspend to ram
in order for the device to be operational. The reset lives in
synaptics-specific reconnect handler, but it is not being invoked
if synaptics support is disabled and the device is handled as a
standard PS/2 device (bare or IntelliMouse protocol).
Let's add reset into generic reconnect handler as well.
The Microblaze implementations of get_user() and (MMU) put_user() evaluate
the address argument more than once. This causes unexpected side-effects for
invocations that include increment operators, i.e. get_user(foo, bar++).
This patch also removes the distinction between MMU and noMMU put_user().
Without the patch:
$ echo 1234567890 > /proc/sys/kernel/core_pattern
$ cat /proc/sys/kernel/core_pattern
12345
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
perf record: Add a fallback to the reference relocation symbol
Usually "_text" is enough, but I received reports that its not always
available, so fallback to "_stext" for the symbol we use to check if we
need to apply any relocation to all the symbols in the kernel symtab,
for when, for instance, kexec is being used.
Reported-by: Darren Hart <dvhltc@us.ibm.com> Reported-by: Steven Rostedt <rostedt@goodmis.org> Cc: Frédéric Weisbecker <fweisbec@gmail.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jan Kiszka [Tue, 11 May 2010 13:16:46 +0000 (15:16 +0200)]
KVM: VMX: blocked-by-sti must not defer NMI injections
As the processor may not consider GUEST_INTR_STATE_STI as a reason for
blocking NMI, it could return immediately with EXIT_REASON_NMI_WINDOW
when we asked for it. But as we consider this state as NMI-blocking, we
can run into an endless loop.
Resolve this by allowing NMI injection if just GUEST_INTR_STATE_STI is
active (originally suggested by Gleb). Intel confirmed that this is
safe, the processor will never complain about NMI injection in this
state.
Joerg Roedel [Wed, 5 May 2010 14:04:43 +0000 (16:04 +0200)]
KVM: SVM: Fix wrong intercept masks on 32 bit
This patch makes KVM on 32 bit SVM working again by
correcting the masks used for iret interception. With the
wrong masks the upper 32 bits of the intercepts are masked
out which leaves vmrun unintercepted. This is not legal on
svm and the vmrun fails.
Bug was introduced by commits 95ba827313 and 3cfc3092.
Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: Gleb Natapov <gleb@redhat.com> Cc: stable@kernel.org Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Avi Kivity <avi@redhat.com>
Linus Torvalds [Thu, 13 May 2010 01:48:26 +0000 (18:48 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/perf_event: Fix oops due to perf_event_do_pending call
powerpc/swiotlb: Fix off by one in determining boundary of which ops to use
projects / karo-tx-linux.git / log