It's possible for an initiator to send us an UNMAP command with a
descriptor that is less than 8 bytes; in that case it's really bad for
us to set an unsigned int to that value, subtract 8 from it, and then
use that as a limit for our loop (since the value will wrap around to
a huge positive value).
Fix this by making size be signed and only looping if size >= 16 (ie
if we have at least a full descriptor available).
Also remove offset as an obfuscated name for the constant 8.
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[bwh: Backported to 3.2: adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UNMAP DATA LENGTH and UNMAP BLOCK DESCRIPTOR DATA LENGTH fields
are in the unmap descriptor (the payload transferred to our data out
buffer), not in the CDB itself. Read them from the correct place in
target_emulated_unmap.
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[bwh: Backported to 3.2: adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When processing an UNMAP command, we need to make sure that the number
of blocks we're asked to UNMAP does not exceed our reported maximum
number of blocks per UNMAP, and that the range of blocks we're
unmapping doesn't go past the end of the device.
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[bwh: Backported to 3.2: adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a process creates a large hugetlbfs mapping that is eligible for page
table sharing and forks heavily with children some of whom fault and
others which destroy the mapping then it is possible for page tables to
get corrupted. Some teardowns of the mapping encounter a "bad pmd" and
output a message to the kernel log. The final teardown will trigger a
BUG_ON in mm/filemap.c.
This was reproduced in 3.4 but is known to have existed for a long time
and goes back at least as far as 2.6.37. It was probably was introduced
in 2.6.20 by [39dde65c: shared page table for hugetlb page]. The messages
look like this;
The bug is a race and not always easy to reproduce. To reproduce it I was
doing the following on a single socket I7-based machine with 16G of RAM.
$ hugeadm --pool-pages-max DEFAULT:13G
$ echo $((18*1048576*1024)) > /proc/sys/kernel/shmmax
$ echo $((18*1048576*1024)) > /proc/sys/kernel/shmall
$ for i in `seq 1 9000`; do ./hugetlbfs-test; done
On my particular machine, it usually triggers within 10 minutes but
enabling debug options can change the timing such that it never hits.
Once the bug is triggered, the machine is in trouble and needs to be
rebooted. The machine will respond but processes accessing proc like "ps
aux" will hang due to the BUG_ON. shutdown will also hang and needs a
hard reset or a sysrq-b.
The basic problem is a race between page table sharing and teardown. For
the most part page table sharing depends on i_mmap_mutex. In some cases,
it is also taking the mm->page_table_lock for the PTE updates but with
shared page tables, it is the i_mmap_mutex that is more important.
Unfortunately it appears to be also insufficient. Consider the following
situation
In this scenario, it is possible for Process A to share page tables with
Process B that is trying to tear them down. The i_mmap_mutex on its own
does not prevent Process A walking Process B's page tables. At (1) above,
the page tables are not shared yet so it unmaps the PMDs. Process A sets
up page table sharing and at (2) faults a new entry. Process B then trips
up on it in free_pgtables.
This patch fixes the problem by adding a new function
__unmap_hugepage_range_final that is only called when the VMA is about to
be destroyed. This function clears VM_MAYSHARE during
unmap_hugepage_range() under the i_mmap_mutex. This makes the VMA
ineligible for sharing and avoids the race. Superficially this looks like
it would then be vunerable to truncate and madvise issues but hugetlbfs
has its own truncate handlers so does not use unmap_mapping_range() and
does not support madvise(DONTNEED).
This should be treated as a -stable candidate if it is merged.
Test program is as follows. The test case was mostly written by Michal
Hocko with a few minor changes to reproduce this bug.
Mix in any architectural randomness in extract_buf() instead of
xfer_secondary_buf(). This allows us to mix in more architectural
randomness, and it also makes xfer_secondary_buf() faster, moving a
tiny bit of additional CPU overhead to process which is extracting the
randomness.
[ Commit description modified by tytso to remove an extended
advertisement for the RDRAND instruction. ]
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Acked-by: Ingo Molnar <mingo@kernel.org> Cc: DJ Johnston <dj.johnston@intel.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many platforms have per-machine instance data (serial numbers,
asset tags, etc.) squirreled away in areas that are accessed
during early system bringup. Mixing this data into the random
pools has a very high value in providing better random data,
so we should allow (and even encourage) architecture code to
call add_device_randomness() from the setup_arch() paths.
However, this limits our options for internal structure of
the random driver since random_initialize() is not called
until long after setup_arch().
Add a big fat comment to rand_initialize() spelling out
this requirement.
With the new interrupt sampling system, we are no longer using the
timer_rand_state structure in the irq descriptor, so we can stop
initializing it now.
[ Merged in fixes from Sedat to find some last missing references to
rand_initialize_irq() ]
The tamper evident features of the RTC include the "write counter" which
is a pseudo-random number regenerated whenever we set the RTC. Since this
value is unpredictable it should provide some useful seeding to the random
number generator.
Only do this on boot since the goal is to seed the pool rather than add
useful entropy.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create a new function, get_random_bytes_arch() which will use the
architecture-specific hardware random number generator if it is
present. Change get_random_bytes() to not use the HW RNG, even if it
is avaiable.
The reason for this is that the hw random number generator is fast (if
it is present), but it requires that we trust the hardware
manufacturer to have not put in a back door. (For example, an
increasing counter encrypted by an AES key known to the NSA.)
It's unlikely that Intel (for example) was paid off by the US
Government to do this, but it's impossible for them to prove otherwise
--- especially since Bull Mountain is documented to use AES as a
whitener. Hence, the output of an evil, trojan-horse version of
RDRAND is statistically indistinguishable from an RDRAND implemented
to the specifications claimed by Intel. Short of using a tunnelling
electronic microscope to reverse engineer an Ivy Bridge chip and
disassembling and analyzing the CPU microcode, there's no way for us
to tell for sure.
Since users of get_random_bytes() in the Linux kernel need to be able
to support hardware systems where the HW RNG is not present, most
time-sensitive users of this interface have already created their own
cryptographic RNG interface which uses get_random_bytes() as a seed.
So it's much better to use the HW RNG to improve the existing random
number generator, by mixing in any entropy returned by the HW RNG into
/dev/random's entropy pool, but to always _use_ /dev/random's entropy
pool.
This way we get almost of the benefits of the HW RNG without any
potential liabilities. The only benefits we forgo is the
speed/performance enhancements --- and generic kernel code can't
depend on depend on get_random_bytes() having the speed of a HW RNG
anyway.
For those places that really want access to the arch-specific HW RNG,
if it is available, we provide get_random_bytes_arch().
If the CPU supports a hardware random number generator, use it in
xfer_secondary_pool(), where it will significantly improve things and
where we can afford it.
Also, remove the use of the arch-specific rng in
add_timer_randomness(), since the call is significantly slower than
get_cycles(), and we're much better off using it in
xfer_secondary_pool() anyway.
Add a new interface, add_device_randomness() for adding data to the
random pool that is likely to differ between two devices (or possibly
even per boot). This would be things like MAC addresses or serial
numbers, or the read-out of the RTC. This does *not* add any actual
entropy to the pool, but it initializes the pool to different values
for devices that might otherwise be identical and have very little
entropy available to them (particularly common in the embedded world).
[ Modified by tytso to mix in a timestamp, since there may be some
variability caused by the time needed to detect/configure the hardware
in question. ]
The real-time Linux folks don't like add_interrupt_randomness() taking
a spinlock since it is called in the low-level interrupt routine.
This also allows us to reduce the overhead in the fast path, for the
random driver, which is the interrupt collection path.
We've been moving away from add_interrupt_randomness() for various
reasons: it's too expensive to do on every interrupt, and flooding the
CPU with interrupts could theoretically cause bogus floods of entropy
from a somewhat externally controllable source.
This solves both problems by limiting the actual randomness addition
to just once a second or after 64 interrupts, whicever comes first.
During that time, the interrupt cycle data is buffered up in a per-cpu
pool. Also, we make sure the the nonblocking pool used by urandom is
initialized before we start feeding the normal input pool. This
assures that /dev/urandom is returning unpredictable data as soon as
possible.
(Based on an original patch by Linus, but significantly modified by
tytso.)
Tested-by: Eric Wustrow <ewust@umich.edu> Reported-by: Eric Wustrow <ewust@umich.edu> Reported-by: Nadia Heninger <nadiah@cs.ucsd.edu> Reported-by: Zakir Durumeric <zakir@umich.edu> Reported-by: J. Alex Halderman <jhalderm@umich.edu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The touchpad on the Acer Aspire One D250 will report out of range values
in the extreme lower portion of the touchpad. These appear as abrupt
changes in the values reported by the hardware from very low values to
very high values, which can cause unexpected vertical jumps in the
position of the mouse pointer.
What seems to be happening is that the value is wrapping to a two's
compliment negative value of higher resolution than the 13-bit value
reported by the hardware, with the high-order bits being truncated. This
patch adds handling for these values by converting them to the
appropriate negative values.
The only tricky part about this is deciding when to treat a number as
negative. It stands to reason that if out of range values can be
reported on the low end then it could also happen on the high end, so
not all out of range values should be treated as negative. The approach
taken here is to split the difference between the maximum legitimate
value for the axis and the maximum possible value that the hardware can
report, treating values greater than this number as negative and all
other values as positive. This can be tweaked later if hardware is found
that operates outside of these parameters.
The Intel case falls through into the generic case which then changes
the values. For cases like the P6 it doesn't do the right thing so
this seems to be a screwup.
wireless: Save original maximum regulatory transmission power for the calucation of the local maximum transmit pow
changed the way we calculate chan->max_power as min(chan->max_power,
chan->max_reg_power). That broke rt2x00 (and perhaps some other
drivers) that do not set chan->max_power. It is not so easy to fix this
problem correctly in rt2x00.
According to commit eccc068e8 changelog, change claim only to save
maximum regulatory power - changing setting of chan->max_power was side
effect. This patch restore previous calculations of chan->max_power and
do not touch chan->max_reg_power.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AR1111 is same as AR9485. The h/w
difference between them is quite insignificant,
Felix suggests only very few baseband features
may not be available in AR1111. The h/w code for
AR9485 is already present, so AR1111 should
work fine with the addition of its PID/VID.
Reported-by: Tim Bentley <Tim.Bentley@Gmail.com> Cc: Felix Bitterli <felixb@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Tested-by: Tim Bentley <Tim.Bentley@Gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a fixed TEI is used, the initial state of the layer 2 statmachine need to be
4 (TEI assigned). This was true only for Point to Point connections, but not
for the other fixed TEIs. It was not found before, because usually only the
TEI 0 is used as fixed TEI for PtP mode, but if you try X31 packet mode
connections with SAPI 16, TEI 1, it did fail.
Signed-off-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 99b725084 "ACPI processor hotplug: Delay acpi_processor_start()
call for hotplugged cores", acpi_processor_hotplug(pr) was wrongly replaced
by acpi_processor_cst_has_changed() inside the acpi_cpu_soft_notify(). This
patch will restore it back, fixing the tick_broadcast_mask regression:
https://lkml.org/lkml/2012/7/30/169
Signed-off-by: Feng Tang <feng.tang@intel.com> Cc: Thomas Renninger <trenn@suse.de> Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl> Reviewed-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Presently the oops code looks for the pgd either from the mm context or
the cached TTB value. There are presently cases where the TTB can be
unset or otherwise cleared by hardware, which we weren't handling,
resulting in recursive faults on the NULL pgd. In these cases we can
simply reload from swapper_pg_dir and continue on as normal.
Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reproducing is easy, I can hit it on a KVM system with a very basic
config (x86_64 make defconfig + enable the drivers needed). To hit it,
just install dump (on debian/ubuntu, not sure what the package might be
called on Fedora), and:
dump -o -f /tmp/foo /
You'll see the warning in dmesg once it forks off the I/O process and
starts dumping filesystem contents.
Currently ioc->nr_tasks is used to decide two things - whether an ioc
is done issuing IOs and whether it's shared by multiple tasks. This
patch separate out the first into ioc->active_ref, which is acquired
and released using {get|put}_io_context_active() respectively.
This will be used to associate bio's with a given task. This patch
doesn't introduce any visible behavior change.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
It seems like the init of ioc->nr_tasks was removed in that patch,
so it starts out at 0 instead of 1.
Tejun, is the right thing here to add back the init, or should something else
be done?
The below patch removes the warning, but I haven't done any more extensive
testing on it.
Line 0 and 1 were both written to line 0 (on the display) and all subsequent
lines had an offset of -1. The result was that the last line on the display
was never overwritten by writes to /dev/fbN.
If a resync of a RAID1 array with 2 devices finds a known bad block
one device it will neither read from, or write to, that device for
this block offset.
So there will be one read_target (The other device) and zero write
targets.
This condition causes md/raid1 to abort the resync assuming that it
has finished - without known bad blocks this would be true.
When there are no write targets because of the presence of bad blocks
we should only skip over the area covered by the bad block.
RAID10 already gets this right, raid1 doesn't. Or didn't.
As this can cause a 'sync' to abort early and appear to have succeeded
it could lead to some data corruption, so it suitable for -stable.
mmu_notifier_release() is called when the process is exiting. It will
delete all the mmu notifiers. But at this time the page belonging to the
process is still present in page tables and is present on the LRU list, so
this race will happen:
CPU 0 CPU 1
mmu_notifier_release: try_to_unmap:
hlist_del_init_rcu(&mn->hlist);
ptep_clear_flush_notify:
mmu nofifler not found
free page !!!!!!
/*
* At the point, the page has been
* freed, but it is still mapped in
* the secondary MMU.
*/
mn->ops->release(mn, mm);
Then the box is not stable and sometimes we can get this bug:
[ 738.075923] BUG: Bad page state in process migrate-perf pfn:03bec
[ 738.075931] page:ffffea00000efb00 count:0 mapcount:0 mapping: (null) index:0x8076
[ 738.075936] page flags: 0x20000000000014(referenced|dirty)
The same issue is present in mmu_notifier_unregister().
We can call ->release before deleting the notifier to ensure the page has
been unmapped from the secondary MMU before it is freed.
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com> Cc: Avi Kivity <avi@redhat.com> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On architectures with CONFIG_HUGETLB_PAGE_SIZE_VARIABLE set, such as
Itanium, pageblock_order is a variable with default value of 0. It's set
to the right value by set_pageblock_order() in function
free_area_init_core().
But pageblock_order may be used by sparse_init() before free_area_init_core()
is called along path:
sparse_init()
->sparse_early_usemaps_alloc_node()
->usemap_size()
->SECTION_BLOCKFLAGS_BITS
->((1UL << (PFN_SECTION_SHIFT - pageblock_order)) *
NR_PAGEBLOCK_BITS)
The uninitialized pageblock_size will cause memory wasting because
usemap_size() returns a much bigger value then it's really needed.
For example, on an Itanium platform,
sparse_init() pageblock_order=0 usemap_size=24576
free_area_init_core() before pageblock_order=0, usemap_size=24576
free_area_init_core() after pageblock_order=12, usemap_size=8
That means 24K memory has been wasted for each section, so fix it by calling
set_pageblock_order() from sparse_init().
Signed-off-by: Xishi Qiu <qiuxishi@huawei.com> Signed-off-by: Jiang Liu <liuj97@gmail.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: David Rientjes <rientjes@google.com> Cc: Keping Chen <chenkeping@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While trying to get a v3.5 kernel booted on the cubox, I noticed that
VFP does not work correctly with VFP bounce handling. This is because
of the confusion over 16-bit vs 32-bit instructions, and where PC is
supposed to point to.
The rule is that FP handlers are entered with regs->ARM_pc pointing at
the _next_ instruction to be executed. However, if the exception is
not handled, regs->ARM_pc points at the faulting instruction.
This is easy for ARM mode, because we know that the next instruction and
previous instructions are separated by four bytes. This is not true of
Thumb2 though.
Since all FP instructions are 32-bit in Thumb2, it makes things easy.
We just need to select the appropriate adjustment. Do this by moving
the adjustment out of do_undefinstr() into the assembly code, as only
the assembly code knows whether it's dealing with a 32-bit or 16-bit
instruction.
Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer OMAP CPU's are SMP machines so omap2plus_defconfig sets
CONFIG_SMP=y. Unfortunately on an OMAP UP machine is_smp()
returns false and smp_init_cpus() is never called and the
smp_cross_call() function remains NULL.
If the machine is rebooted or powered off, smp_send_stop() will
be called (since CONFIG_SMP=y) leading to the following error:
Add a check so smp_cross_call() is only called when there is more than one CPU on-line.
Signed-off-by: Javier Martinez Canillas <javier at dowhile0.org> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vivt_flush_cache_{range,page} functions check that the mm_struct
of the VMA being flushed has been active on the current CPU before
performing the cache maintenance.
The gate_vma has a NULL mm_struct pointer and, as such, will cause a
kernel fault if we try to flush it with the above operations. This
happens during ELF core dumps, which include the gate_vma as it may be
useful for debugging purposes.
This patch adds checks to the VIVT cache flushing functions so that VMAs
with a NULL mm_struct are flushed unconditionally (the vectors page may
be dirty if we use it to store the current TLS pointer).
Reported-by: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org> Tested-by: Uros Bizjak <ubizjak@gmail.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cdf357f1 ("ARM: 6299/1: errata: TLBIASIDIS and TLBIMVAIS
operations can broadcast a faulty ASID") replaced by-ASID TLB flushing
operations with all-ASID variants to workaround A9 erratum #720789.
This patch extends the workaround to include the tlb_range operations,
which were overlooked by the original patch.
Tested-by: Steve Capper <steve.capper@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vfp_pm_suspend should save the VFP state in suspend after
any lazy context switch. If it only saves when the VFP is enabled,
the state can get lost when, on a UP system:
Thread 1 uses the VFP
Context switch occurs to thread 2, VFP is disabled but the
VFP context is not saved
Thread 2 initiates suspend
vfp_pm_suspend is called with the VFP disabled, and the unsaved
VFP context of Thread 1 in the registers
Modify vfp_pm_suspend to save the VFP context whenever
vfp_current_hw_state is not NULL.
Includes a fix from Ido Yariv <ido@wizery.com>, who pointed out that on
SMP systems, the state pointer can be pointing to a freed task struct if
a task exited on another cpu, fixed by using #ifndef CONFIG_SMP in the
new if clause.
Signed-off-by: Colin Cross <ccross@android.com> Cc: Barry Song <bs14@csr.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Ido Yariv <ido@wizery.com> Cc: Daniel Drake <dsd@laptop.org> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vfp_pm_suspend runs on each cpu, only clear the hardware state
pointer for the current cpu. Prevents a possible crash if one
cpu clears the hw state pointer when another cpu has already
checked if it is valid.
Signed-off-by: Colin Cross <ccross@android.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CPU will endlessly spin at the end of machine_halt and
machine_restart calls. However, this will lead to a soft lockup
warning after about 20 seconds, if CONFIG_LOCKUP_DETECTOR is enabled,
as system timer is still alive.
Disable interrupt before going to spin endlessly, so that the lockup
warning will never be seen.
Reported-by: Marek Vasut <marex@denx.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a6bc32b89922 ("mm: compaction: introduce sync-light migration for
use by compaction") changed the declaration of migrate_pages() and
migrate_huge_pages().
But it missed changing the argument of migrate_huge_pages() in
soft_offline_huge_page(). In this case, we should call
migrate_huge_pages() with MIGRATE_SYNC.
Additionally, there is a mismatch between type the of argument and the
function declaration for migrate_pages().
Signed-off-by: Joonsoo Kim <js1304@gmail.com> Cc: Christoph Lameter <cl@linux.com> Cc: Mel Gorman <mgorman@suse.de> Acked-by: David Rientjes <rientjes@google.com> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The may_enter_fs test turns out to be too restrictive: though I saw no
problem with it when testing on 3.5-rc6, it very soon OOMed when I tested
on 3.5-rc6-mm1. I don't know what the difference there is, perhaps I just
slightly changed the way I started off the testing: dd if=/dev/zero
of=/mnt/temp bs=1M count=1024; rm -f /mnt/temp; sync repeatedly, in 20M
memory.limit_in_bytes cgroup to ext4 on USB stick.
ext4 (and gfs2 and xfs) turn out to allocate new pages for writing with
AOP_FLAG_NOFS: that seems a little worrying, and it's unclear to me why
the transaction needs to be started even before allocating pagecache
memory. But it may not be worth worrying about these days: if direct
reclaim avoids FS writeback, does __GFP_FS now mean anything?
Anyway, we insisted on the may_enter_fs test to avoid hangs with the loop
device; but since that also masks off __GFP_IO, we can test for __GFP_IO
directly, ignoring may_enter_fs and __GFP_FS.
But even so, the test still OOMs sometimes: when originally testing on
3.5-rc6, it OOMed about one time in five or ten; when testing just now on
3.5-rc6-mm1, it OOMed on the first iteration.
This residual problem comes from an accumulation of pages under ordinary
writeback, not marked PageReclaim, so rightly not causing the memcg check
to wait on their writeback: these too can prevent shrink_page_list() from
freeing any pages, so many times that memcg reclaim fails and OOMs.
Deal with these in the same way as direct reclaim now deals with dirty FS
pages: mark them PageReclaim. It is appropriate to rotate these to tail
of list when writepage completes, but more importantly, the PageReclaim
flag makes memcg reclaim wait on them if encountered again. Increment
NR_VMSCAN_IMMEDIATE? That's arguable: I chose not.
Setting PageReclaim here may occasionally race with end_page_writeback()
clearing it: lru_deactivate_fn() already faced the same race, and
correctly concluded that the window is small and the issue non-critical.
With these changes, the test runs indefinitely without OOMing on ext4,
ext3 and ext2: I'll move on to test with other filesystems later.
Trivia: invert conditions for a clearer block without an else, and goto
keep_locked to do the unlock_page.
Signed-off-by: Hugh Dickins <hughd@google.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujtisu.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Rik van Riel <riel@redhat.com> Cc: Ying Han <yinghan@google.com> Cc: Greg Thelen <gthelen@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Fengguang Wu <fengguang.wu@intel.com> Acked-by: Michal Hocko <mhocko@suse.cz> Cc: Dave Chinner <david@fromorbit.com> Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation of dirty pages throttling is not memcg aware
which makes it easy to have memcg LRUs full of dirty pages. Without
throttling, these LRUs can be scanned faster than the rate of writeback,
leading to memcg OOM conditions when the hard limit is small.
This patch fixes the problem by throttling the allocating process
(possibly a writer) during the hard limit reclaim by waiting on
PageReclaim pages. We are waiting only for PageReclaim pages because
those are the pages that made one full round over LRU and that means that
the writeback is much slower than scanning.
The solution is far from being ideal - long term solution is memcg aware
dirty throttling - but it is meant to be a band aid until we have a real
fix. We are seeing this happening during nightly backups which are placed
into containers to prevent from eviction of the real working set.
The change affects only memcg reclaim and only when we encounter
PageReclaim pages which is a signal that the reclaim doesn't catch up on
with the writers so somebody should be throttled. This could be
potentially unfair because it could be somebody else from the group who
gets throttled on behalf of the writer but as writers need to allocate as
well and they allocate in higher rate the probability that only innocent
processes would be penalized is not that high.
I have tested this change by a simple dd copying /dev/zero to tmpfs or
ext3 running under small memcg (1G copy under 5M, 60M, 300M and 2G
containers) and dd got killed by OOM killer every time. With the patch I
could run the dd with the same size under 5M controller without any OOM.
The issue is more visible with slower devices for output.
* With the patch
================
* tmpfs size=2G
---------------
$ vim cgroup_cache_oom_test.sh
$ ./cgroup_cache_oom_test.sh 5M
using Limit 5M for group
1000+0 records in
1000+0 records out 1048576000 bytes (1.0 GB) copied, 30.4049 s, 34.5 MB/s
$ ./cgroup_cache_oom_test.sh 60M
using Limit 60M for group
1000+0 records in
1000+0 records out 1048576000 bytes (1.0 GB) copied, 31.4561 s, 33.3 MB/s
$ ./cgroup_cache_oom_test.sh 300M
using Limit 300M for group
1000+0 records in
1000+0 records out 1048576000 bytes (1.0 GB) copied, 20.4618 s, 51.2 MB/s
$ ./cgroup_cache_oom_test.sh 2G
using Limit 2G for group
1000+0 records in
1000+0 records out 1048576000 bytes (1.0 GB) copied, 1.42172 s, 738 MB/s
* ext3
------
$ ./cgroup_cache_oom_test.sh 5M
using Limit 5M for group
1000+0 records in
1000+0 records out 1048576000 bytes (1.0 GB) copied, 27.9547 s, 37.5 MB/s
$ ./cgroup_cache_oom_test.sh 60M
using Limit 60M for group
1000+0 records in
1000+0 records out 1048576000 bytes (1.0 GB) copied, 30.3221 s, 34.6 MB/s
$ ./cgroup_cache_oom_test.sh 300M
using Limit 300M for group
1000+0 records in
1000+0 records out 1048576000 bytes (1.0 GB) copied, 24.5764 s, 42.7 MB/s
$ ./cgroup_cache_oom_test.sh 2G
using Limit 2G for group
1000+0 records in
1000+0 records out 1048576000 bytes (1.0 GB) copied, 3.35828 s, 312 MB/s
* Without the patch
===================
* tmpfs size=2G
---------------
$ ./cgroup_cache_oom_test.sh 5M
using Limit 5M for group
./cgroup_cache_oom_test.sh: line 46: 4668 Killed dd if=/dev/zero of=$OUT/zero bs=1M count=$count
$ ./cgroup_cache_oom_test.sh 60M
using Limit 60M for group
1000+0 records in
1000+0 records out 1048576000 bytes (1.0 GB) copied, 25.4989 s, 41.1 MB/s
$ ./cgroup_cache_oom_test.sh 300M
using Limit 300M for group
1000+0 records in
1000+0 records out 1048576000 bytes (1.0 GB) copied, 24.3928 s, 43.0 MB/s
$ ./cgroup_cache_oom_test.sh 2G
using Limit 2G for group
1000+0 records in
1000+0 records out 1048576000 bytes (1.0 GB) copied, 1.49797 s, 700 MB/s
* ext3
------
$ ./cgroup_cache_oom_test.sh 5M
using Limit 5M for group
./cgroup_cache_oom_test.sh: line 46: 4689 Killed dd if=/dev/zero of=$OUT/zero bs=1M count=$count
$ ./cgroup_cache_oom_test.sh 60M
using Limit 60M for group
./cgroup_cache_oom_test.sh: line 46: 4692 Killed dd if=/dev/zero of=$OUT/zero bs=1M count=$count
$ ./cgroup_cache_oom_test.sh 300M
using Limit 300M for group
1000+0 records in
1000+0 records out 1048576000 bytes (1.0 GB) copied, 20.248 s, 51.8 MB/s
$ ./cgroup_cache_oom_test.sh 2G
using Limit 2G for group
1000+0 records in
1000+0 records out 1048576000 bytes (1.0 GB) copied, 2.85201 s, 368 MB/s
[akpm@linux-foundation.org: tweak changelog, reordered the test to optimize for CONFIG_CGROUP_MEM_RES_CTLR=n]
[hughd@google.com: fix deadlock with loop driver] Reviewed-by: Mel Gorman <mgorman@suse.de> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Michal Hocko <mhocko@suse.cz> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujtisu.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Rik van Riel <riel@redhat.com> Cc: Ying Han <yinghan@google.com> Cc: Greg Thelen <gthelen@google.com> Cc: Hugh Dickins <hughd@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
efi_setup_pcdp_console() is called during boot to parse the HCDP/PCDP
EFI system table and setup an early console for printk output. The
routine uses ioremap/iounmap to setup access to the HCDP/PCDP table
information.
The call to ioremap is happening early in the boot process which leads
to a panic on x86_64 systems:
This replaces the calls to ioremap/iounmap in efi_setup_pcdp_console()
with calls to early_ioremap/early_iounmap which can be called during
early boot.
This patch was tested on an x86_64 prototype system which uses the
HCDP/PCDP table for early console setup.
Signed-off-by: Greg Pearson <greg.pearson@hp.com> Acked-by: Khalid Aziz <khalid.aziz@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
from commit a8f3c203e19b702fa5e8e83a9b6fb3c5a6d1cce4
restore the mapping scheme for uncached buffers,
which was changed in a common scheme for cached and uncached.
This apparently was wrong, and was probably intended only for cached buffers.
the fix fixes the crash observed while mapping uncached buffers.
The V4L2_CID_ISO_SENSITIVITY control menu values should be
standard ISO values multiplied by 1000. Multiply all menu
items by 1000 so ISO is properly reported as 50...3200 range.
commit 9ef449c6b31bb6a8e6dedc24de475a3b8c79be20 ("[media] rc: Postpone ISR
registration") fixed an early ISR registration on several drivers. It did
however also introduced a bug by moving the invocation of pnp_port_start()
to the end of the probe function.
This patch fixes this issue by moving the invocation of pnp_port_start() to
an earlier stage in the probe function.
Signed-off-by: Luis Henriques <luis.henriques@canonical.com> Cc: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
where the thaw ioctl deadlocked at thaw_super() when called while chcp was
waiting at nilfs_transaction_begin() called from
nilfs_ioctl_change_cpmode(). This deadlock is 100% reproducible.
This is because nilfs_ioctl_change_cpmode() first locks sb->s_umount in
read mode and then waits for unfreezing in nilfs_transaction_begin(),
whereas thaw_super() locks sb->s_umount in write mode. The locking of
sb->s_umount here was intended to make snapshot mounts and the downgrade
of snapshots to checkpoints exclusive.
This fixes the deadlock issue by replacing the sb->s_umount usage in
nilfs_ioctl_change_cpmode() with a dedicated mutex which protects snapshot
mounts.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Cc: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp> Tested-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The test for the fillempty condition was wrong in one place.
Changed the variable to the right boolean type.
Signed-off-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this patch kernel will panic on LockD start, because lockd_up() checks
lockd_up_net() result for negative value.
From my pow it's better to return negative value from rpcbind routines instead
of replacing all such checks like in lockd_up().
The intent behind this behavior was to return "pK-error" in cases where
the %pK format specifier was used in interrupt context, because the
CAP_SYSLOG check wouldn't be meaningful. Clearly this should only apply
when kptr_restrict is actually enabled though.
Reported-by: Stevie Trujillo <stevie.trujillo@gmail.com> Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OK, what we have so far is e.g.
setxattr(path, name, whatever, 0, XATTR_REPLACE)
with name being good enough to get through xattr_permission().
Then we reach security_inode_setxattr() with the desired value and size.
Aha. name should begin with "security.selinux", or we won't get that
far in selinux_inode_setxattr(). Suppose we got there and have enough
permissions to relabel that sucker. We call security_context_to_sid()
with value == NULL, size == 0. OK, we want ss_initialized to be non-zero.
I.e. after everything had been set up and running. No problem...
We do 1-byte kmalloc(), zero-length memcpy() (which doesn't oops, even
thought the source is NULL) and put a NUL there. I.e. form an empty
string. string_to_context_struct() is called and looks for the first
':' in there. Not found, -EINVAL we get. OK, security_context_to_sid_core()
has rc == -EINVAL, force == 0, so it silently returns -EINVAL.
All it takes now is not having CAP_MAC_ADMIN and we are fucked.
All right, it might be a different bug (modulo strange code quoted in the
report), but it's real. Easily fixed, AFAICS:
Deal with size == 0, value == NULL case in selinux_inode_setxattr()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Tested-by: Dave Jones <davej@redhat.com> Reported-by: Dave Jones <davej@redhat.com> Signed-off-by: James Morris <james.l.morris@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to responses from the BIOS team, ASUS_WMI_METHODID_DSTS2
(0x53545344) will be used as future DSTS ID. In addition, calling
asus_wmi_evaluate_method(ASUS_WMI_METHODID_DSTS2, 0, 0, NULL) returns
ASUS_WMI_UNSUPPORTED_METHOD in new ASUS laptop PCs. This patch fixes
no DSTS ID will be assigned in this case.
Signed-off-by: Alex Hung <alex.hung@canonical.com> Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following build error occured during a ia64 build with
swap-over-NFS patches applied.
net/core/sock.c:274:36: error: initializer element is not constant
net/core/sock.c:274:36: error: (near initialization for 'memalloc_socks')
net/core/sock.c:274:36: error: initializer element is not constant
This is identical to a parisc build error. Fengguang Wu, Mel Gorman
and James Bottomley did all the legwork to track the root cause of
the problem. This fix and entire commit log is shamelessly copied
from them with one extra detail to change a dubious runtime use of
ATOMIC_INIT() to atomic_set() in drivers/char/mspec.c
Dave Anglin says:
> Here is the line in sock.i:
>
> struct static_key memalloc_socks = ((struct static_key) { .enabled =
> ((atomic_t) { (0) }) });
The above line contains two compound literals. It also uses a designated
initializer to initialize the field enabled. A compound literal is not a
constant expression.
The location of the above statement isn't fully clear, but if a compound
literal occurs outside the body of a function, the initializer list must
consist of constant expressions.
Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Block layer will allocate a spinlock for the queue if the driver does
not provide one in blk_init_queue().
The reason to use the internal spinlock is that blk_cleanup_queue() will
switch to use the internal spinlock in the cleanup code path.
if (q->queue_lock != &q->__queue_lock)
q->queue_lock = &q->__queue_lock;
However, processes which are in D state might have taken the driver
provided spinlock, when the processes wake up, they would release the
block provided spinlock.
=====================================
[ BUG: bad unlock balance detected! ]
3.4.0-rc7+ #238 Not tainted
-------------------------------------
fio/3587 is trying to release lock (&(&q->__queue_lock)->rlock) at:
[<ffffffff813274d2>] blk_queue_bio+0x2a2/0x380
but there are no more locks to release!
other info that might help us debug this:
1 lock held by fio/3587:
#0: (&(&vblk->lock)->rlock){......}, at:
[<ffffffff8132661a>] get_request_wait+0x19a/0x250
Other drivers use block layer provided spinlock as well, e.g. SCSI.
Switching to the block layer provided spinlock saves a bit of memory and
does not increase lock contention. Performance test shows no real
difference is observed before and after this patch.
Changes in v2: Improve commit log as Michael suggested.
Signed-off-by: Asias He <asias@redhat.com> Cc: virtualization@lists.linux-foundation.org Cc: kvm@vger.kernel.org Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
blk_cleanup_queue() will call blk_drian_queue() to drain all the
requests before queue DEAD marking. If we reset the device before
blk_cleanup_queue() the drain would fail.
1) if the queue is stopped in do_virtblk_request() because device is
full, the q->request_fn() will not be called.
blk_drain_queue() {
while(true) {
...
if (!list_empty(&q->queue_head))
__blk_run_queue(q) {
if (queue is not stoped)
q->request_fn()
}
...
}
}
Do no reset the device before blk_cleanup_queue() gives the chance to
start the queue in interrupt handler blk_done().
2) In commit b79d866c8b7014a51f611a64c40546109beaf24a, We abort requests
dispatched to driver before blk_cleanup_queue(). There is a race if
requests are dispatched to driver after the abort and before the queue
DEAD mark. To fix this, instead of aborting the requests explicitly, we
can just reset the device after after blk_cleanup_queue so that the
device can complete all the requests before queue DEAD marking in the
drain process.
Signed-off-by: Asias He <asias@redhat.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: virtualization@lists.linux-foundation.org Cc: kvm@vger.kernel.org Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
del_gendisk() might not return due to failing to remove the
/sys/block/vda/serial sysfs entry when another thread (udev) is
trying to read it.
virtblk_remove()
vdev->config->reset() : guest will not kick us through interrupt
del_gendisk()
device_del()
kobject_del(): got stuck, sysfs entry ref count non zero
sysfs_open_file(): user space process read /sys/block/vda/serial
sysfs_get_active() : got sysfs entry ref count
dev_attr_show()
virtblk_serial_show()
blk_execute_rq() : got stuck, interrupt is disabled
request cannot be finished
This patch fixes it by calling del_gendisk() before we disable guest's
interrupt so that the request sent in virtblk_serial_show() will be
finished and del_gendisk() will success.
This fixes another race in hot-unplug process.
It is save to call del_gendisk(vblk->disk) before
flush_work(&vblk->config_work) which might access vblk->disk, because
vblk->disk is not freed until put_disk(vblk->disk).
Signed-off-by: Asias He <asias@redhat.com> Cc: virtualization@lists.linux-foundation.org Cc: kvm@vger.kernel.org Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If uaddr == uaddr2, then we have broken the rule of only requeueing
from a non-pi futex to a pi futex with this call. If we attempt this,
as the trinity test suite manages to do, we miss early wakeups as
q.key is equal to key2 (because they are the same uaddr). We will then
attempt to dereference the pi_mutex (which would exist had the futex_q
been properly requeued to a pi futex) and trigger a NULL pointer
dereference.
The WARN_ON in futex_wait_requeue_pi() for a NULL q.pi_state was testing
the address (&q.pi_state) of the pointer instead of the value
(q.pi_state) of the pointer. Correct it accordingly.
Lenovo Thinkpad T530 with ALC269VC codec has a dock port but BIOS
doesn't set up the pins properly. Enable the pins as well as on
Thinkpad X230 Tablet.
The IDT codecs initializes the GPIO setup for mute LEDs via
snd_hda_sync_vmaster_hook(). This works in most cases except for the
very first call, which is called before PCM and control creations.
Thus before Master switch is set manually via alsactl, the mute LED
may show the wrong state, depending on the polarity.
Now it's fixed by calling the LED-status update function manually when
no vmaster is set yet.
The commit a3e199732b made the LED working again on HP Mini 210 but
with a wrong polarity. This patch fixes the polarity for this
machine, and also introduce a new model string "hp-inv-led".
BIOS on HP Mini 210 doesn't provide the proper "HP_Mute_LED" DMI
string, thus the driver doesn't initialize the GPIO, too. In the
earlier kernel, the driver falls back to GPIO1, but since 3.3 we've
stopped this due to other wrongly advertised machines.
For fixing this particular case, add a new model type to specify the
default polarity explicitly so that the fallback to GPIO1 is handled.
We've got a bug report about the silent output from the headphone on a
mobo with VT2021, and spotted out that this was because of the wrong
D3 state on the DAC for the headphone output. The bug is triggered by
the incomplete check for this DAC in set_widgets_power_state_vt1718S().
It checks only the connectivity of the primary output (0x27) but
doesn't consider the path from the headphone pin (0x28).
Now this patch fixes the problem by checking both pins for DAC 0x0b.
The irq field of struct snd_mpu401 is supposed to be initialized to -1.
Since it's set to zero as of now, a probing error before the irq
installation results in a kernel warning "Trying to free already-free
IRQ 0".
uac_clock_source_is_valid() uses the control selector value to access
the bmControls bitmap of the clock source unit. This is wrong, as
control selector values start from 1, while the bitmap uses all
available bits.
In other words, "Clock Validity Control" is stored in D3..2, not D5..4
of the clock selector unit's bmControls.
Signed-off-by: Daniel Mack <zonque@gmail.com> Reported-by: Andreas Koch <andreas@akdesigninc.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default 10 microsecond delay for the controller to come out of
halt in dbgp_ehci_startup is too short, so increase it to 1 millisecond.
This is based on emperical testing on various USB debug ports on
modern machines such as a Lenovo X220i and an Ivybridge development
platform that needed to wait ~450-950 microseconds.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tun module leaks up to 36 bytes of memory by not fully initializing
a structure located on the stack that gets copied to user memory by the
TUNGETIFF and SIOCGIFHWADDR ioctl()s.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Back in 2006, commit 1a2449a87b ("[I/OAT]: TCP recv offload to I/OAT")
added support for receive offloading to IOAT dma engine if available.
The code in tcp_rcv_established() tries to perform early DMA copy if
applicable. It however does so without checking whether the userspace
task is actually expecting the data in the buffer.
This is not a problem under normal circumstances, but there is a corner
case where this doesn't work -- and that's when MSG_TRUNC flag to
recvmsg() is used.
If the IOAT dma engine is not used, the code properly checks whether
there is a valid ucopy.task and the socket is owned by userspace, but
misses the check in the dmaengine case.
This problem can be observed in real trivially -- for example 'tbench' is a
good reproducer, as it makes a heavy use of MSG_TRUNC. On systems utilizing
IOAT, you will soon find tbench waiting indefinitely in sk_wait_data(), as they
have been already early-copied in tcp_rcv_established() using dma engine.
This patch introduces the same check we are performing in the simple
iovec copy case to the IOAT case as well. It fixes the indefinite
recvmsg(MSG_TRUNC) hangs.
Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When device flags are set using rtnetlink, IFF_PROMISC and IFF_ALLMULTI
flags are handled specially. Function dev_change_flags sets IFF_PROMISC and
IFF_ALLMULTI bits in dev->gflags according to the passed value but
do_setlink passes a result of rtnl_dev_combine_flags which takes those bits
from dev->flags.
This can be easily trigerred by doing:
tcpdump -i eth0 &
ip l s up eth0
ip sets IFF_UP flag in ifi_flags and ifi_change, which is combined with
IFF_PROMISC by rtnl_dev_combine_flags, causing __dev_change_flags to set
IFF_PROMISC in gflags.
Reported-by: Max Matveev <makc@redhat.com> Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem is that we call this with a spin lock held. The call tree
is:
kaweth_start_xmit() holds kaweth->device_lock.
-> kaweth_async_set_rx_mode()
-> kaweth_control()
-> kaweth_internal_control_msg()
The kaweth_internal_control_msg() function is only called from
kaweth_control() which used GFP_ATOMIC for its allocations.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCP_USER_TIMEOUT is a TCP level socket option that takes an unsigned int. But
patch "tcp: Add TCP_USER_TIMEOUT socket option"(dca43c75) didn't check the negative
values. If a user assign -1 to it, the socket will set successfully and wait
for 4294967295 miliseconds. This patch add a negative value check to avoid
this issue.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: <rucsoftsec@gmail.com>
Resolves-bug: http://bugzilla.kernel.org/show_bug?44441 Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First it appears in bisection, then reverting it solves the usual
netdev watchdog problem for different people. I don't have a proper
fix yet so get rid of it.
Bisected-and-reported-by: Alex Villacís Lasso <a_villacis@palosanto.com> Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Josh Boyer <jwboyer@redhat.com> Cc: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In net/compat.c::put_cmsg_compat() we may assign 'data' the address of
either the 'ctv' or 'cts' local variables inside the 'if
(!COMPAT_USE_64BIT_TIME)' branch.
Those variables go out of scope at the end of the 'if' statement, so
when we use 'data' further down in 'copy_to_user(CMSG_COMPAT_DATA(cm),
data, cmlen - sizeof(struct compat_cmsghdr))' there's no telling what
it may be refering to - not good.
Fix the problem by simply giving 'ctv' and 'cts' function scope.
Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In xattr block operation, we use h_refcount to indicate whether the
xattr block is shared among many inodes. And xattr block csum uses
s_csum_seed if it is shared and i_csum_seed if it belongs to
one inode. But this has a problem. So consider the block is shared
first bewteen inode A and B, and B has some xattr update and CoW
the xattr block. When it updates the *old* xattr block(because
of the h_refcount change) and calls ext4_xattr_release_block, we
has no idea that inode A is the real owner of the *old* xattr
block and we can't use the i_csum_seed of inode A either in xattr
block csum calculation. And I don't think we have an easy way to
find inode A.
So this patch just removes the tricky i_csum_seed and we now uses
s_csum_seed every time for the xattr block csum. The corresponding
patch for the e2fsprogs will be sent in another patch.
This is spotted by xfstests 117.
Signed-off-by: Tao Ma <boyu.mt@taobao.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Acked-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ext4_rename, when the old name is a dir, we need to
change ".." to its new parent and journal the change, so
with metadata_csum enabled, we have to re-calc the csum.
As the first block of the dir can be either a htree root
or a normal directory block and we have different csum
calculation for these 2 types, we have to choose the right
one in ext4_rename.
btw, it is found by xfstests 013.
Signed-off-by: Tao Ma <boyu.mt@taobao.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Acked-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function ext4_calc_metadata_amount() has side effects, although
it's not obvious from its function name. So if we fail to claim
space, regardless of whether we retry to claim the space again, or
return an error, we need to undo these side effects.
Otherwise we can end up incorrectly calculating the number of metadata
blocks needed for the operation, which was responsible for an xfstests
failure for test #271 when using an ext2 file system with delalloc
enabled.
If we hit a condition where we have allocated metadata blocks that
were not appropriately reserved, we risk underflow of
ei->i_reserved_meta_blocks. In turn, this can throw
sbi->s_dirtyclusters_counter significantly out of whack and undermine
the nondelalloc fallback logic in ext4_nonda_switch(). Warn if this
occurs and set i_allocated_meta_blocks to avoid this problem.
This condition is reproduced by xfstests 270 against ext2 with
delalloc enabled:
Mar 28 08:58:02 localhost kernel: [ 171.526344] EXT4-fs (loop1): delayed block allocation failed for inode 14 at logical offset 64486 with max blocks 64 with error -28
Mar 28 08:58:02 localhost kernel: [ 171.526346] EXT4-fs (loop1): This should not happen!! Data will be lost
270 ultimately fails with an inconsistent filesystem and requires an
fsck to repair. The cause of the error is an underflow in
ext4_da_update_reserve_space() due to an unreserved meta block
allocation.
Whether to continue removing extents or not is decided by the return
value of function ext4_ext_more_to_rm() which checks 2 conditions:
a) if there are no more indexes to process.
b) if the number of entries are decreased in the header of "depth -1".
In case of hole punch, if the last block to be removed is not part of
the last extent index than this index will not be deleted, hence the
number of valid entries in the extent header of "depth - 1" will
remain as it is and ext4_ext_more_to_rm will return 0 although the
required blocks are not yet removed.
This patch fixes the above mentioned problem as instead of removing
the extents from the end of file, it starts removing the blocks from
the particular extent from which removing blocks is actually required
and continue backward until done.
Commit f975d6bcc7a introduced bug which caused ext4_statfs() to
miscalculate the number of file system overhead blocks. This causes
the f_blocks field in the statfs structure to be larger than it should
be. This would in turn cause the "df" output to show the number of
data blocks in the file system and the number of data blocks used to
be larger than they should be.
Linear copy works by adding the offset to the buffer address,
which may end up not being 16-byte aligned.
Some tests I've written for prime_pcopy show that the engine
allows this correctly, so the restriction on lowest 4 bits of
address can be lifted safely.
The comments added were by envyas, I think because I used
a newer version.
(1) Only registered key types can be passed to the core keys code, so
register the legacy idmapper key type.
This is a requirement because the unregister function cleans up keys
belonging to that key type so that there aren't dangling pointers to the
module left behind - including the key->type pointer.
(2) Rename the legacy key type. You can't have two key types with the same
name, and (1) would otherwise require that.
(3) complete_request_key() must be called in the error path of
nfs_idmap_legacy_upcall().
(4) There is one idmap struct for each nfs_client struct. This means that
idmap->idmap_key_cons is shared without the use of a lock. This is a
problem because key_instantiate_and_link() - as called indirectly by
idmap_pipe_downcall() - releases anyone waiting for the key to be
instantiated.
What happens is that idmap_pipe_downcall() running in the rpc.idmapd
thread, releases the NFS filesystem in whatever thread that is running in
to continue. This may then make another idmapper call, overwriting
idmap_key_cons before idmap_pipe_downcall() gets the chance to call
complete_request_key().
I *think* that reading idmap_key_cons only once, before
key_instantiate_and_link() is called, and then caching the result in a
variable is sufficient.
projects / karo-tx-linux.git / log