Added 0x0307 device id to support Motorola cables to the pl2303 usb
serial driver. This cable has a modified chip that is a pl2303, but
declares itself as 0307. Fixed by adding the right device id to the
supported devices list, assigning it the code labeled
PL2303_PRODUCT_ID_MOTOROLA.
The outvq needs to be woken up on host notifications so that buffers
consumed by the host can be reclaimed, outvq freed, and application
writes may proceed again.
The need for this is now finally noticed when I have qemu patches ready
to use nonblocking IO and flow control.
CC: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Under harsh testing conditions, including low memory, the guest would
stop receiving packets. With this patch applied we no longer see any
problems in the driver while performing these tests for extended periods
of time.
Make sure napi is scheduled subsequent to each napi_enable.
Signed-off-by: Bruce Rogers <brogers@novell.com> Signed-off-by: Olaf Kirch <okir@suse.de> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove real devices first and dummy devices last. This gives device
driver which instantiated dummy devices themselves a chance to clean
them up before we do.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Tested-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
P54_HDR_FLAG_DATA_OUT_SEQNR is meant to tell the
firmware that "the frame's sequence number has
already been set by the application."
Whereas IEEE80211_TX_CTL_ASSIGN_SEQ is set for
frames which lack a valid sequence number and
either the driver or firmware has to assign one.
Yup, it's the exact opposite!
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following scenario is possible with the current cpuidle code and
the ACPI cpuidle driver:
(1) acpi_processor_cst_has_changed() is called,
(2) cpuidle_disable_device() is called,
(3) cpuidle_remove_state_sysfs() is called to remove the (presumably
outdated) states info from sysfs,
(3) acpi_processor_get_power_info() is called, the first entry in the
pr->power.states[] table is filled with zeros,
(4) acpi_processor_setup_cpuidle() is called and it doesn't fill the
first entry in pr->power.states[],
(5) cpuidle_enable_device() is called,
(6) __cpuidle_register_device() is _not_ called, since the device has
already been registered,
(7) Consequently, poll_idle_init() is _not_ called either,
(8) cpuidle_add_state_sysfs() is called to create the sysfs attributes
for the new states and it uses the bogus first table entry from
acpi_processor_get_power_info() for creating state0.
This problem is avoided if cpuidle_enable_device()
unconditionally calls poll_idle_init().
Reported-by: Len Brown <len.brown@intel.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the redundant syscalls prototypes in the architecture
specific syscalls.h header file. These were identical with the ones in
asm-generic/syscalls.h.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Reported-by: Peter Huewe <PeterHuewe@gmx.de> Reported-by: Sven Schnelle <svens@stackframe.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A check against division by zero was modified in commit b0525b48.
Since this change time_to_empty_now is always reported as zero
while the battery is discharging and as a negative value while
the battery is charging. This is because current is negative while
the battery is discharging.
Fix the check introduced by commit b0525b48 so that time_to_empty_now
is reported correctly during discharge and as zero while charging.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com> Acked-by: Daniel Mack <daniel@caiaq.de> Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We sometimes need to map between the virtio device and
the given pci device. One such use is OS installer that
gets the boot pci device from BIOS and needs to
find the relevant block device. Since it can't,
installation fails.
Instead of creating a top-level devices/virtio-pci
directory, create each device under the corresponding
pci device node. Symlinks to all virtio-pci
devices can be found under the pci driver link in
bus/pci/drivers/virtio-pci/devices, and all virtio
devices under drivers/bus/virtio/devices.
Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Acked-by: Michael S. Tsirkin <mst@redhat.com> Tested-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Gleb Natapov <gleb@redhat.com> Tested-by: "Daniel P. Berrange" <berrange@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pci-stub uses strsep() to separate list of ids and generates a warning
message when it fails to parse an id. However, not specifying the
parameter results in ids set to an empty string. strsep() happily
returns the empty string as the first token and thus triggers the
warning message spuriously.
When p3_ioremap() was converted to ioremap_prot() there was some breakage
introduced where the 29-bit segmentation logic would trap the area range
and return an identity mapping without having allowed the area
specification to force mapping through page tables. This wires up a PCC
mask for pgprot verification to work out whether to short-circuit the
identity mapping on legacy parts, restoring the previous behaviour.
In fsl_rio_dbell_handler() the code currently simply acknowledges the QFI
queue full interrupt, but does nothing to resolve the queue full
condition. Instead, it jumps to the end of the isr. When a queue full
condition occurs, the isr is then re-entered immediately and continually,
forever.
The fix is to just fall through and read out current doorbell entries.
Signed-off-by: Thomas Taranowski <tom@baringforge.com> Cc: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Li Yang <leoli@freescale.com> Cc: Thomas Moll <thomas.moll@sysgo.com> Cc: Micha Nelissen <micha@neli.hopto.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 40389687 moved a call to ext4_forget() out of
ext4_free_branches and let ext4_free_blocks() handle calling
bforget(). But that change unfortunately did not replace the call to
ext4_forget() with brelse(), which was needed to drop the in-use count
of the indirect block's buffer head, which lead to a memory leak when
deleting files that used indirect blocks. Fix this.
Increased usage of page migration in mmotm reveals that the anon_vma
locking in unmap_and_move() has been deficient since 2.6.36 (or even
earlier). Review at the time of f18194275c39835cb84563500995e0d503a32d9a
("mm: fix hang on anon_vma->root->lock") missed the issue here: the
anon_vma to which we get a reference may already have been freed back to
its slab (it is in use when we check page_mapped, but that can change),
and so its anon_vma->root may be switched at any moment by reuse in
anon_vma_prepare.
Perhaps we could fix that with a get_anon_vma_unless_zero(), but let's
not: just rely on page_lock_anon_vma() to do all the hard thinking for us,
then we don't need any rcu read locking over here.
In removing the rcu_unlock label: since PageAnon is a bit in
page->mapping, it's impossible for a !page->mapping page to be anon; but
insert VM_BUG_ON in case the implementation ever changes.
rtc-cmos was setting suspend/resume hooks at the device_driver level.
However, the platform bus code (drivers/base/platform.c) only looks for
resume hooks at the dev_pm_ops level, or within the platform_driver.
Switch rtc_cmos to use dev_pm_ops so that suspend/resume code is executed
again.
Paul said:
: The user visible symptom in our (XO laptop) case was that rtcwake would
: fail to wake the laptop. The RTC alarm would expire, but the wakeup
: wasn't unmasked.
:
: As for severity, the impact may have been reduced because if I recall
: correctly, the bug only affected platforms with CONFIG_PNP disabled.
Signed-off-by: Paul Fox <pgf@laptop.org> Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 34aacb2920 ("procfs: Use generic_file_llseek in /proc/kcore") broke
seeking on /proc/kcore. This changes it back to use default_llseek in
order to restore the original behavior.
The problem with generic_file_llseek is that it only allows seeks up to
inode->i_sb->s_maxbytes, which is 2GB-1 on procfs, where the memory file
offset values in the /proc/kcore PT_LOAD segments may exceed or start
beyond that offset value.
A similar revert was made for /proc/vmcore.
Signed-off-by: Dave Anderson <anderson@redhat.com> Acked-by: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no reason to be freeing the delegation cred in the rcu callback,
and doing so is resulting in a lockdep complaint that rpc_credcache_lock
is being called from both softirq and non-softirq contexts.
When we disable the WM8994 FLL code path sharing means that we end up
writing out a configuration. Currently this is the currently active
input and output frequency (which causes snd_soc_update_bits() to
suppress actual writes both immediately and in the common case where
we reenable the same configuration later) but we allow machine drivers
to pass through a source of zero. Since the register values written
are one less than the source constants this causes corruption of other
bitfields in the register.
Fix this by using the most recently configured FLL source when none is
provided.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a timer interrupt was delayed too much, hrtimer_forward_now() will
forward the timer expiry more than once. When this happens, the
additional number of elapsed ALSA timer ticks must be passed to
snd_timer_interrupt() to prevent the ALSA timer from falling behind.
This mostly fixes MIDI slowdown problems on highly-loaded systems with
badly behaved interrupt handlers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Reported-and-tested-by: Arthur Marsh <arthur.marsh@internode.on.net> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Conexant codec driver adds the jack arrays in init callback which
may be called also in each PM resume. This results in the addition of
new jack element at each time.
The fix is to check whether the requested jack is already present in
the array.
This patch fixes the non-compiling AC97C driver for AVR32 architecture by
include mach/hardware.h only for AT91 architecture. The AVR32 architecture does
not supply the hardware.h include file.
Fix playback/capture channels patch to change supported playback
channels of au8830 to 1,2,4 and capture channels to 1,2.
This prevent oops when oss emulation use SNDCTL_DSP_CHANNELS to
set 3 Channels
gcc 4.5+ doesn't properly evaluate some inlined expressions.
A previous patch were proposed by Andrew Morton using noinline.
However, the entire inlined function is bogus, so let's just
remove it and be happy.
We should be enabling country IE hints for WIPHY_FLAG_STRICT_REGULATORY
even if we haven't yet recieved regulatory domain hint for the driver
if it needed one. Without this Country IEs are not passed on to drivers
that have set WIPHY_FLAG_STRICT_REGULATORY, today this is just all
Atheros chipset drivers: ath5k, ath9k, ar9170, carl9170.
This was part of the original design, however it was completely
overlooked...
Cc: Easwar Krishnan <easwar.krishnan@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Easwar Krishnan <easwar.krishnan@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There was a configuration page timing out during the initial port
enable at driver load time. The port enable would fail, and this would
result in the driver unloading itself, meanwhile the driver was accessing
freed memory in another context resulting in the panic. The fix is to
prevent access to freed memory once the driver had issued the diag reset
which woke up the sleeping port enable process. The routine
_base_reset_handler was reorganized so the last sleeping process woken up was
the port_enable.
The ioc->hba_queue_depth is not properly resized when the controller
firmware reports that it supports more outstanding IO than what can be fit
inside the reply descriptor pool depth. This is reproduced by setting the
controller global credits larger than 30,000. The bug results in an
incorrect sizing of the queues. The fix is to resize the queue_size by
dividing queue_diff by two.
False timeout after hard resets, there were two issues which leads
to timeout.
(1) Panic because of invalid memory access in the broadcast asyn
event processing routine due to a race between accessing the scsi command
pointer from broadcast asyn event processing thread and completing
the same scsi command from the interrupt context.
(2) Broadcast asyn event notifcations are not handled due to events
ignored while the broadcast asyn event is activity being processed
from the event process kernel thread.
In addition, changed the ABRT_TASK_SET to ABORT_TASK in the
broadcast async event processing routine. This is less disruptive to other
request that generate Broadcast Asyn Primitives besides target
reset. e.g clear reservations, microcode download,and mode select.
The "internal device reset complete" event is not supported
for older firmware prior to MPI Rev K We added
a check in the driver so the "internal device reset" event is
ignored for older firmware. When ignored, the tm_busy flag doesn't
get set nor cleared. Without this fix, IO queues would be froozen
indefinetly after the "internal device reset" event, as the "complete" event
never sent to clear the flag.
When zoning end devices, the driver is not sending device
removal handshake alogrithm to firmware. This results in controller
firmware not sending sas topology add events the next time the device is
added. The fix is the driver should be doing the device removal handshake
even though the PHYSTATUS_VACANT bit is set in the PhyStatus of the
event data. The current design is avoiding the handshake when the
VACANT bit is set in the phy status.
Issue:
IR shutdown(sending) and IR shutdown(complete) messages not
listed in /var/log/messages when driver is removed.
The driver needs to issue a MPI2_RAID_ACTION_SYSTEM_SHUTDOWN_INITIATED
request when the driver is unloaded so the IR metadata journal is updated.
If this request is not sent, then the volume would need a "check
consistency" issued on the next bootup if the volume was roamed from one
initiator to another. The current driver supports this feature only when the
system is rebooted, however this also need to be supported if the driver is
unloaded
Fix:
To fix this issue, the driver is going
to need to call the _scsih_ir_shutdown prior to reporting
the volumes missing from the OS, hence the device handles
are still present.
libsas makes use of scsi_schedule_eh() but forgets to clear the
host_eh_scheduled flag in its error handling routine. Because of this,
the error handler thread never gets to sleep; it's constantly awake and
trying to run the error routine leading to console spew and inability to
run anything else (at least on a UP system). The fix is to clear the
flag as we splice the work queue.
Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Our current handling of medium error assumes that data is returned up
to the bad sector. This assumption holds good for all disk devices,
all DIF arrays and most ordinary arrays. However, an LSI array engine
was recently discovered which reports a medium error without returning
any data. This means that when we report good data up to the medium
error, we've reported junk originally in the buffer as good. Worse,
if the read consists of requested data plus a readahead, and the error
occurs in readahead, we'll just strip off the readahead and report
junk up to userspace as good data with no error.
The fix for this is to have the error position computation take into
account the amount of data returned by the driver using the scsi
residual data. Unfortunately, not every driver fills in this data,
but for those who don't, it's set to zero, which means we'll think a
full set of data was transferred and the behaviour will be identical
to the prior behaviour of the code (believe the buffer up to the error
sector). All modern drivers seem to set the residual, so that should
fix up the LSI failure/corruption case.
Reported-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If QIOASSIST is enabled for a qdio device the SIGA instruction requires
a modified function code. This function code modifier was missing for
SIGA-R and SIGA-S which can lead to a kernel panic caused by an
operand exception.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bit 6 & 7 of AR_WA (0x4004) should be enabled only
for the chips that are supporting L0s functionality
while resuming back from S3/S4.
Enabling these bits for AR9280 is causing system hang
within a few S3/S4-resume cycles.
Cc: Jack Lee <jlee@atheros.com> Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AR9003's PAPRD was enabled prematurely, and is causing some
large discrepancies on throughput and network connectivity.
For example downlink (RX) throughput against an AR9280 AP
can vary widlely from 43-73 Mbit/s while disabling this
gets AR9382 (2x2) up to around 93 Mbit/s in a 2.4 GHz HT20 setup.
Cc: Paul Shaw <paul.shaw@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The power detector adc offset calibration has to be done
on 4 minutes interval (longcal * pa_skip_count). But the commit
"ath9k_hw: fix a noise floor calibration related race condition"
makes the PA calibration executed more frequently beased on
nfcal_pending value. Running PAOffset calibration lesser than
longcal interval doesn't help anything and the worse part is that
it causes NF load timeouts and RX deaf conditions.
In a very noisy environment, where the distance b/w AP & station
is ~10 meter and running a downlink udp traffic with frequent
background scan causes "Timeout while waiting for nf to load:
AR_PHY_AGC_CONTROL=0x40d1a" and moves the chip into deaf state.
This issue was originaly reported in Android platform where
the network-manager application does bgscan more frequently
on AR9271 chips. (AR9285 family usb device).
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ath9k supports its own set of virtual wiphys, and it uses
the mac80211 idle notifications to know when a device needs
to be idle or not. We recently changed ath9k to force idle
on driver stop() and on resume but forgot to take into account
ath9k's own virtual wiphy idle states. These are used internally
by ath9k to check if the device's radio should be powered down
on each idle call. Without this change its possible that the
device could have been forced off but the virtual wiphy idle
was left on.
Cc: Paul Stewart <pstew@google.com> Cc: Amod Bodas <amod.bodas@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
mac80211 will notify drivers when to go idle and ath9k
assumed that it would get further notifications for idle
states after a device stop() config call but as per agreed
semantics the idle state of the radio is left up to driver
after mac80211 issues the stop() callback. The driver is
resposnbile for ensuring the device remains idle after
that even between suspend / resume calls.
This fixes suspend/resume when you issue suspend and resume
twice on ath9k when ath9k_stop() was already called. We need
to put the radio to full sleep in order for resume to work
correctly.
What might seem fishy is we are turning the radio off
after resume. The reason why we do this is because we know
we should not have anything enabled after a mac80211 tells
us to stop(), if we resume and never get a start() we won't
get another stop() by mac80211 so to be safe always bring
the 802.11 device with the radio disabled after resume,
this ensures that if we suspend we already have the radio
disabled and only a start() will ever trigger it on.
Cc: Paul Stewart <pstew@google.com> Cc: Amod Bodas <amod.bodas@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PCU lock should be used to contend TX DMA as well,
this will be done next.
This is part of a series of patches which fix stopping
TX DMA completley when requested on the driver.
For more details about this issue refer to this thread:
Tested-by: Ben Greear <greearb@candelatech.com> Cc: Kyungwan Nam <kyungwan.nam@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new PCU lock is better placed so we can just contend
against that when trying to reset hardware.
This is part of a series of patches which fix stopping
TX DMA completley when requested on the driver.
For more details about this issue refer to this thread:
Tested-by: Ben Greear <greearb@candelatech.com> Cc: Kyungwan Nam <kyungwan.nam@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Re-enable the interrupt when it occurs to see all transitions.
Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit 6cd0b1cb872b3bf9fc5de4536404206ab74bafdd "iwlagn: fix
hw-rfkill while the interface is down", we enable interrupts when
device is not ready to receive them. However hardware, when it is in
some inconsistent state, can generate other than rfkill interrupts
and crash the system. I can reproduce crash with "kernel BUG at
drivers/net/wireless/iwlwifi/iwl-agn.c:1010!" message, when forcing
firmware restarts.
To fix only enable rfkill interrupt when down device and after probe.
I checked patch on laptop with 5100 device, rfkill change is still
passed to user space when device is down.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The change 'mac80211: Fix BUG in pskb_expand_head when transmitting shared skbs'
added a check for copying the skb if it's shared, however the tx info variable
still points at the cb of the old skb
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some drivers (e.g. ath9k) do not always disable beacons when they're
supposed to. When an interface is changed using the change_interface op,
the mode specific sdata part is in an undefined state and trying to
get a beacon at this point can produce weird crashes.
To fix this, add a check for ieee80211_sdata_running before using
anything from the sdata.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the buffer size is set to zero in the block ack parameter set
field, we should use the maximum supported number of subframes. The
existing code was bogus and was doing some unnecessary calculations
that lead to wrong values.
Thanks Johannes for helping me figure this one out.
Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Luciano Coelho <coelho@ti.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
removed the synchronization against RCU and thus
opened a race window where we can use a key for
TX while it is already freed. Put a synchronisation
into the right place to close that window.
Reported-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Under memory pressure, the mac80211 mesh code
may helpfully print a message that it failed
to clone a mesh frame and then will proceed
to crash trying to use it anyway. Fix that.
Avoid the reference whenever the frame copy is unsuccessful
regardless of the debug message being suppressed or printed.
Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The hv_netvsc gets RNDIS_STATUS_MEDIA_CONNECT event after the VM
is live migrated. Adding call to netif_notify_peers() for this event
to send GARP (Gratuitous ARP) to notify network peers. Otherwise,
the VM's network connection may stop after a live migration.
This patch should also be applied to stable kernel 2.6.32 and later.
The ni_labpc driver module only requests a shared IRQ for PCI devices,
requesting a non-shared IRQ for non-PCI devices.
As this module is also used by the ni_labpc_cs module for certain
National Instruments PCMCIA cards, it also needs to request a shared IRQ
for PCMCIA devices, otherwise you get a IRQ mismatch with the CardBus
controller.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In zram_read() and zram_write() we were not incrementing the
index number and thus were reading/writing values from/to
incorrect sectors on zram disk, resulting in data corruption.
The USB core keeps track of pending resume requests for root hubs, in
order to resolve races between wakeup requests and suspends. However
the code that does this is subject to another race (between wakeup
requests and resumes) because the WAKEUP_PENDING flag is cleared
before the resume occurs, leaving a window in which another wakeup
request might arrive.
This patch (as1447) fixes the problem by clearing the WAKEUP_PENDING
flag after the resume instead of before it.
This fixes Bugzilla #24952.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Paul Bender <pebender@san.rr.com> Tested-by: warpme <warpme@o2.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If anyone comes across a high-speed hub that (by mistake or by design)
claims to have no Transaction Translators, plugging a full- or
low-speed device into it will cause the USB stack to crash. This
patch (as1446) prevents the problem by ignoring such devices, since
the kernel has no way to communicate with them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Perry Neben <neben@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The major and minor number saved in the product_info structure
were copied from the address instead of the data, causing an
inconsistency in the reported versions during firmware loading:
usb 4-1: firmware: requesting edgeport/down.fw
/usr/src/linux/drivers/usb/serial/io_edgeport.c: downloading firmware version (930) 1.16.4
[..]
/usr/src/linux/drivers/usb/serial/io_edgeport.c: edge_startup - time 3 4328191260
/usr/src/linux/drivers/usb/serial/io_edgeport.c: FirmwareMajorVersion 0.0.4
This can cause some confusion whether firmware loaded successfully
or not.
This patch (as1442) fixes a bug in g_printer: Module parameters should
not be marked "__initdata" if they are accessible in sysfs (i.e., if
the mode value in the module_param() macro is nonzero). Otherwise
attempts to access the parameters will cause addressing violations.
Character-string module parameters must not be marked "__initdata"
if the module can be unloaded, because the kernel needs to access the
parameter variable at unload time in order to free the
dynamically-allocated string.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Roland Kletzing <devzero@web.de> CC: Craig W. Nadler <craig@nadler.us> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1441) fixes a bug in g_printer. The gadget driver, char
device number, and class device should be unregistered in reverse
order of registration. As it is now, when the module is unloaded the
class device gets unregistered first, causing a crash when the unbind
method tries to access it.
This fixes Bugzilla #25882.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Roland Kletzing <devzero@web.de> CC: Craig W. Nadler <craig@nadler.us> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1440) fixes a bug in ehci-hcd. ehci->periodic_size is
used to compute the size in a dma_alloc_coherent() call, but then it
gets changed later on. As a result, the corresponding call to
dma_free_coherent() passes a different size from the original
allocation. Fix the problem by adjusting ehci->periodic_size before
carrying out any of the memory allocations.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> CC: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1443) fixes a bug found in many of the USB serial
drivers: They don't set the .usb_driver field in their
usb_serial_driver structure. This field is needed for assigning
dynamic IDs for device matching.
In addition, starting with the 2.6.37 kernel, the .usb_driver field is
needed for proper autosuspend operation. Without it, attempts to open
the device file will fail.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
/drivers/usb/serial/option.c: Adding support for Cinterion's HC25, HC28,
HC28J, EU3-E, EU3-P and PH8 by correcting/adding Cinterion's and
Siemens' Vendor IDs as well as Product IDs and USB_DEVICE tuples
Signed-off-by: Nicolaus Colberg <nicolaus.colberg@cinterion.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I found the original patch on the db0fhn repeater wiki (couldn't find the email
of the origial author) I guess it was never commited.
I updated and added some Icom HAM-radio devices to the ftdi driver.
Added extra comments to make clear what devices it are.
This patch (as1438) adds an unusual_devs entry for the MagicPixel
FW_Omega2 chip, used in the CamSport Evo camera. The firmware
incorrectly reports a vendor-specific bDeviceClass.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: <ttkspam@free.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The TrekStor DataStation maxi g.u external hard drive enclosure uses a
JMicron USB to SATA chip which needs the US_FL_IGNORE_RESIDUE flag to work
properly.
Signed-off-by: Richard Schütz <r.schtz@t-online.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Device ID removed 0x10C4/0x8149 for West Mountain Radio Computerized
Battery Analyzer. This device is actually based on a SiLabs C8051Fxxx,
see http://www.etheus.net/SiUSBXp_Linux_Driver for further info.
projects / karo-tx-linux.git / log