Daniel Mack [Wed, 18 Jun 2014 09:01:43 +0000 (11:01 +0200)]
net: phy: at803x: Add support for hardware reset
The AT8030 will enter a FIFO error mode if a packet is transmitted while
the cable is unplugged. This hardware issue is acknowledged by the
vendor, and the only proposed solution is to conduct a hardware reset
via the external pin each time the link goes down. There is apparantly
no way to fix up the state via the register set.
This patch adds support for reading a 'reset-gpios' property from the DT
node of the PHY. If present, this gpio is used to apply a hardware reset
each time a 'link down' condition is detected. All relevant registers
are read out before, and written back after the reset cycle.
Doing this every time the link goes down might seem like overkill, but
there is unfortunately no way of figuring out whether the PHY is in
such a lock-up state. Hence, this is the only way of reliably fixing up
things.
Signed-off-by: Daniel Mack <zonque@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Mack [Wed, 18 Jun 2014 09:01:41 +0000 (11:01 +0200)]
net: phylib: add link_change_notify callback to phy device
Add a notify callback to inform phy drivers when the core is about to
do its link adjustment. No change for drivers that do not implement
this callback.
Signed-off-by: Daniel Mack <zonque@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Wed, 18 Jun 2014 05:46:02 +0000 (13:46 +0800)]
8021q: fix a potential memory leak
skb_cow called in vlan_reorder_header does not free the skb when it failed,
and vlan_reorder_header returns NULL to reset original skb when it is called
in vlan_untag, lead to a memory leak.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Please pull this batch of fixes intended for the 3.16 stream!
For the Bluetooth bits, Gustavo says:
"This is our first batch of fixes for 3.16. Be aware that two patches here
are not exactly bugfixes:
* 71f28af57066 Bluetooth: Add clarifying comment for conn->auth_type
This commit just add some important security comments to the code, we found
it important enough to include it here for 3.16 since it is security related.
* 9f7ec8871132 Bluetooth: Refactor discovery stopping into its own function
This commit is just a refactor in a preparation for a fix in the next
commit (f8680f128b).
All the other patches are fixes for deadlocks and for the Bluetooth protocols,
most of them related to authentication and encryption."
On top of that...
Chin-Ran Lo fixes a problems with overlapping DMA areas in mwifiex.
Michael Braun corrects a couple of issues in order to enable a new
device in rt2800usb.
Rafał Miłecki reverts a b43 patch that caused a regression, fixes a
Kconfig typo, and corrects a frequency reporting error with the G-PHY.
Stanislaw Grsuzka fixes an rfkill regression for rt2500pci, and avoids
a rt2x00 scheduling while atomic BUG.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 18 Jun 2014 21:46:31 +0000 (23:46 +0200)]
net: sctp: check proc_dointvec result in proc_sctp_do_auth
When writing to the sysctl field net.sctp.auth_enable, it can well
be that the user buffer we handed over to proc_dointvec() via
proc_sctp_do_auth() handler contains something other than integers.
In that case, we would set an uninitialized 4-byte value from the
stack to net->sctp.auth_enable that can be leaked back when reading
the sysctl variable, and it can unintentionally turn auth_enable
on/off based on the stack content since auth_enable is interpreted
as a boolean.
Fix it up by making sure proc_dointvec() returned sucessfully.
Fixes: b14878ccb7fa ("net: sctp: cache auth_enable per endpoint") Reported-by: Florian Westphal <fwestpha@redhat.com> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tg3: Clear NETIF_F_TSO6 flag before doing software GSO
Commit d3f6f3a1d818410c17445bce4f4caab52eb102f1 ("tg3: Prevent page
allocation failure during TSO workaround") modified driver logic
to use tg3_tso_bug() for any TSO fragment that hits hardware bug
conditions thus the patch increased the scope of work for tg3_tso_bug()
to cover devices that support NETIF_F_TSO6 as well. Prior to the
patch, tg3_tso_bug() would only be used on devices supporting
NETIF_F_TSO.
A regression was introduced for IPv6 packets requiring the workaround.
To properly perform GSO on SKBs with TCPV6 gso_type, we need to call
skb_gso_segment() with NETIF_F_TSO6 feature flag cleared, or the
function will return NULL and cause a kernel oops as tg3 is not handling
a NULL return value. This patch fixes the problem.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neal Cardwell [Thu, 19 Jun 2014 01:15:03 +0000 (21:15 -0400)]
tcp: fix tcp_match_skb_to_sack() for unaligned SACK at end of an skb
If there is an MSS change (or misbehaving receiver) that causes a SACK
to arrive that covers the end of an skb but is less than one MSS, then
tcp_match_skb_to_sack() was rounding up pkt_len to the full length of
the skb ("Round if necessary..."), then chopping all bytes off the skb
and creating a zero-byte skb in the write queue.
This was visible now because the recently simplified TLP logic in bef1909ee3ed1c ("tcp: fixing TLP's FIN recovery") could find that 0-byte
skb at the end of the write queue, and now that we do not check that
skb's length we could send it as a TLP probe.
Previously we would find the new_len > skb->len check failing, so we
would fall through and set pkt_len = new_len = 4000 and chop off
pkt_len of 4000 from the 4000-byte skb, leaving a 0-byte segment
afterward in the write queue.
With this new commit, we notice that the new new_len >= skb->len check
succeeds, so that we return without trying to fragment.
Fixes: adb92db857ee ("tcp: Make SACK code to split only at mss boundaries") Reported-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Ilpo Jarvinen <ilpo.jarvinen@helsinki.fi> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kees Cook [Wed, 18 Jun 2014 22:34:57 +0000 (15:34 -0700)]
net: filter: fix upper BPF instruction limit
The original checks (via sk_chk_filter) for instruction count uses ">",
not ">=", so changing this in sk_convert_filter has the potential to break
existing seccomp filters that used exactly BPF_MAXINSNS many instructions.
Fixes: bd4cf0ed331a ("net: filter: rework/optimize internal BPF interpreter's instruction set") Signed-off-by: Kees Cook <keescook@chromium.org> Cc: stable@vger.kernel.org # v3.15+ Acked-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 18 Jun 2014 23:31:30 +0000 (01:31 +0200)]
net: sctp: propagate sysctl errors from proc_do* properly
sysctl handler proc_sctp_do_hmac_alg(), proc_sctp_do_rto_min() and
proc_sctp_do_rto_max() do not properly reflect some error cases
when writing values via sysctl from internal proc functions such
as proc_dointvec() and proc_dostring().
In all these cases we pass the test for write != 0 and partially
do additional work just to notice that additional sanity checks
fail and we return with hard-coded -EINVAL while proc_do*
functions might also return different errors. So fix this up by
simply testing a successful return of proc_do* right after
calling it.
This also allows to propagate its return value onwards to the user.
While touching this, also fix up some minor style issues.
Fixes: 4f3fdf3bc59c ("sctp: add check rto_min and rto_max in sysctl") Fixes: 3c68198e7511 ("sctp: Make hmac algorithm selection for cookie generation dynamic") Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Tue, 17 Jun 2014 13:11:09 +0000 (16:11 +0300)]
bonding: Advertize vxlan offload features when supported
When the underlying device supports TCP offloads for VXLAN/UDP
encapulated traffic, we need to reflect that through the hw_enc_features
field of the bonding net-device. This will cause the xmit path
in the core networking stack to provide bonding with encapsulated
GSO frames to offload into the HW etc.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mirko Lindner [Tue, 17 Jun 2014 10:53:39 +0000 (12:53 +0200)]
skge: Added FS A8NE-FM to the list of 32bit DMA boards
Added FUJITSU SIEMENS A8NE-FM to the list of 32bit DMA boards
>From Tomi O.:
After I added an entry to this MB into the skge.c
driver in order to enable the mentioned 64bit dma disable quirk,
the network data corruptions ended and everything is fine again.
Signed-off-by: Mirko Lindner <mlindner@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following patchset contains netfilter updates for your net tree,
they are:
1) Fix refcount leak when dumping the dying/unconfirmed conntrack lists,
from Florian Westphal.
2) Fix crash in NAT when removing a netnamespace, also from Florian.
3) Fix a crash in IPVS when trying to remove an estimator out of the
sysctl scope, from Julian Anastasov.
4) Add zone attribute to the routing to calculate the message size in
ctnetlink events, from Ken-ichirou MATSUZAWA.
5) Another fix for the dying/unconfirmed list which was preventing to
dump more than one memory page of entries (~17 entries in x86_64).
6) Fix missing RCU-safe list insertion in the rule replacement code
in nf_tables.
7) Since the new transaction infrastructure is in place, we have to
upgrade the chain use counter from u16 to u32 to avoid overflow
after more than 2^16 rules are added.
8) Fix refcount leak when replacing rule in nf_tables. This problem
was also introduced in new transaction.
9) Call the ->destroy() callback when releasing nft-xt rules to fix
module refcount leaks.
10) Set the family in the netlink messages that contain set elements
in nf_tables to make it consistent with other object types.
11) Don't dump NAT port information if it is unset in nft_nat.
12) Update the MAINTAINERS file, I have merged the ebtables entry
into netfilter. While at it, also removed the netfilter users
mailing list, the development list should be enough.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fugang Duan [Wed, 18 Jun 2014 00:33:52 +0000 (08:33 +0800)]
net: fec: Don't clear IPV6 header checksum field when IP accelerator enable
The commit 96c50caa5148 (net: fec: Enable IP header hardware checksum)
enable HW IP header checksum for IPV4 and IPV6, which causes IPV6 TCP/UDP
cannot work. (The issue is reported by Russell King)
For FEC IP header checksum function: Insert IP header checksum. This "IINS"
bit is written by the user. If set, IP accelerator calculates the IP header
checksum and overwrites the IINS corresponding header field with the calculated
value. The checksum field must be cleared by user, otherwise the checksum
always is 0xFFFF.
So the previous patch clear IP header checksum field regardless of IP frame
type.
In fact, IP HW detect the packet as IPV6 type, even if the "IINS" bit is set,
the IP accelerator is not triggered to calculates IPV6 header checksum because
IPV6 frame format don't have checksum.
So this results in the IPV6 frame being corrupted.
The patch just add software detect the current packet type, if it is IPV6
frame, it don't clear IP header checksum field.
Cc: Russell King <linux@arm.linux.org.uk> Reported-and-tested-by: Russell King <linux@arm.linux.org.uk> Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jean Delvare [Tue, 17 Jun 2014 09:59:20 +0000 (11:59 +0200)]
ptp: ptp_pch depends on x86_32
The ptp_pch driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Richard Cochran <richardcochran@gmail.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Niels, starting rfkill polling during device probe
(commit e2bc7c5, generally sane change) broke rfkill on rt2500pci
device. I considered that bug as some initalization issue, which
should be fixed on rt2500pci specific code. But after several
attempts (see bug report for details) we fail to find working solution.
Hence I decided to revert to old behaviour on rt2500pci to fix
regression.
Additionally patch also unregister rfkill on device remove instead
of ifconfig down, what was another issue introduced by bad commit.
Rafał Miłecki [Thu, 12 Jun 2014 20:28:22 +0000 (22:28 +0200)]
b43: fix frequency reported on G-PHY with /new/ firmware
Support for firmware rev 508+ was added years ago, but we never noticed
it reports channel in a different way for G-PHY devices. Instead of
offset from 2400 MHz it simply passes channel id (AKA hw_value).
So far it was (most probably) affecting monitor mode users only, but
the following recent commit made it noticeable for quite everybody:
cfg80211/mac80211: ignore signal if the frame was heard on wrong channel
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Cc: stable@vger.kernel.org Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Braun [Thu, 12 Jun 2014 17:33:41 +0000 (19:33 +0200)]
rt2800usb:fix hang during firmware load
The device 057c:8501 (AVM Fritz! WLAN v2 rev. B) boots into a state that does
not actually require loading a firmware file. The vendors driver finds out
about this by checking a firmware state register, so this patch adds this here.
Finally, with this patch applied, my wifi dongle actually becomes
useful (scan + connect to wpa network works).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Braun [Thu, 12 Jun 2014 17:33:36 +0000 (19:33 +0200)]
rt2800usb:fix efuse detection
The device 057c:8501 (AVM Fritz! WLAN v2 rev. B) currently does not
load. One thing observed is that the vendors driver detects EFUSE mode
for this device, but rt2800usb does not. This is due to rt2800usb
lacking a check for the firmware mode present in the vendors driver,
that this patch adopts for rt2800usb.
With this patch applied, the 'RF chipset' detection does no longer fail.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dave Jones [Mon, 16 Jun 2014 20:59:02 +0000 (16:59 -0400)]
hyperv: fix apparent cut-n-paste error in send path teardown
c25aaf814a63: "hyperv: Enable sendbuf mechanism on the send path" added
some teardown code that looks like it was copied from the recieve path
above, but missed a variable name replacement.
Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Christian Riesch [Mon, 16 Jun 2014 12:46:45 +0000 (14:46 +0200)]
ptp: In the testptp utility, use clock_adjtime from glibc when available
clock_adjtime was included in glibc 2.14. _GNU_SOURCE must be defined
to make it available.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Richard Cochran <richardcochran@gmail.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jean Delvare [Mon, 16 Jun 2014 08:13:55 +0000 (10:13 +0200)]
isdn: hisax: Drop duplicate Kconfig entry
There are 2 HISAX_AVM_A1_PCMCIA Kconfig entries. The kbuild system
ignores the second one, and apparently nobody noticed the problem so
far, so let's remove that second entry.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Karsten Keil <isdn@linux-pingi.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Jean Delvare [Mon, 16 Jun 2014 08:09:37 +0000 (10:09 +0200)]
isdn: hisax: Merge Kconfig ifs
The first half of the HiSax config options is presented if
ISDN_DRV_HISAX!=n, while the second half of the options is presented
if ISDN_DRV_HISAX. That's the same, so merge both conditionals.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Karsten Keil <isdn@linux-pingi.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Tyler Hall [Mon, 16 Jun 2014 02:23:17 +0000 (22:23 -0400)]
slcan: Port write_wakeup deadlock fix from slip
The commit "slip: Fix deadlock in write_wakeup" fixes a deadlock caused
by a change made in both slcan and slip. This is a direct port of that
fix.
Signed-off-by: Tyler Hall <tylerwhall@gmail.com> Cc: Oliver Hartkopp <socketcan@hartkopp.net> Cc: Andre Naujoks <nautsch2@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: linux-kernel@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Tyler Hall [Mon, 16 Jun 2014 02:23:16 +0000 (22:23 -0400)]
slip: Fix deadlock in write_wakeup
Use schedule_work() to avoid potentially taking the spinlock in
interrupt context.
Commit cc9fa74e2a ("slip/slcan: added locking in wakeup function") added
necessary locking to the wakeup function and 367525c8c2/ddcde142be ("can:
slcan: Fix spinlock variant") converted it to spin_lock_bh() because the lock
is also taken in timers.
Disabling softirqs is not sufficient, however, as tty drivers may call
write_wakeup from interrupt context. This driver calls tty->ops->write() with
its spinlock held, which may immediately cause an interrupt on the same CPU and
subsequent spin_bug().
Simply converting to spin_lock_irq/irqsave() prevents this deadlock, but
causes lockdep to point out a possible circular locking dependency
between these locks:
The slip transmit is holding the slip spinlock when calling the tty write.
This grabs the port lock. On an interrupt, the handler grabs the port
lock and calls write_wakeup which grabs the slip lock. This could be a
problem if a serial interrupt occurs on another CPU during the slip
transmit.
To deal with these issues, don't grab the lock in the wakeup function by
deferring the writeout to a workqueue. Also hold the lock during close
when de-assigning the tty pointer to safely disarm the worker and
timers.
This bug is easily reproducible on the first transmit when slip is
used with the standard 8250 serial driver.
Signed-off-by: Tyler Hall <tylerwhall@gmail.com> Cc: Oliver Hartkopp <socketcan@hartkopp.net> Cc: Andre Naujoks <nautsch2@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: linux-kernel@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Fri, 13 Jun 2014 14:03:21 +0000 (10:03 -0400)]
vmxnet3: adjust ring sizes when interface is down
If ethtool is used to update ring sizes on a vmxnet3 interface that isn't
running, the change isn't stored, meaning the ring update is effectively is
ignored and lost without any indication to the user.
Other network drivers store the ring size update so that ring allocation uses
the new sizes next time the interface is brought up. This patch modifies
vmxnet3 to behave this way as well
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: "David S. Miller" <davem@davemloft.net> CC: Shreyas Bhatewara <sbhatewara@vmware.com> CC: "VMware, Inc." <pv-drivers@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chin-Ran Lo [Sat, 7 Jun 2014 02:37:10 +0000 (19:37 -0700)]
mwifiex: fix tx_info/rx_info overlap with PCIe dma_mapping
On PCIe Tx data path, network interface specific tx_info
parameters such as bss_num and bss_type are saved at
"skb->cb + sizeof(dma_addr_t)" (returned by MWIFIEX_SKB_TXCB).
Later mwifiex_map_pci_memory() called from
mwifiex_pcie_send_data() will memcpy
sizeof(struct mwifiex_dma_mapping) bytes to save PCIe DMA
address and length information at beginning of skb->cb.
This accidently overwrites bss_num and bss_type saved in skb->cb
previously because bss_num/bss_type and mwifiex_dma_mapping data
overlap.
Similarly, on PCIe Rx data path, rx_info parameters overlaps
with PCIe DMA address and length information too.
Fix it by defining mwifiex_cb structure and having
MWIFIEX_SKB_TXCB and MWIFIEX_SKB_RXCB return the correct address
of tx_info/rx_info using the structure members.
Also add a BUILD_BUG_ON to maks sure that mwifiex_cb structure
doesn't exceed the size of skb->cb.
Reviewed-by: Aaron Durbin <adurbin@chromium.org> Signed-off-by: Chin-Ran Lo <crlo@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sat, 31 May 2014 17:40:45 +0000 (19:40 +0200)]
b43: disable 5 GHz on G-PHY
This fixes regression introduced by adding some G-PHY devices to the
list of dual band devices. There is simply no support for 5 GHz on
G-PHY devices in b43. It results in:
WARNING: CPU: 0 PID: 79 at drivers/net/wireless/b43/phy_g.c:75 b43_gphy_channel_switch+0x125/0x130 [b43]()
b43-phy1 ERROR: PHY init: Channel switch to default failed
Regression was introduced by the following commit:
Basically what's happening is, during netns cleanup,
nf_nat_net_exit gets called before ipv4_net_exit. As I understand
it, nf_nat_net_exit is supposed to kill any conntrack entries which
have NAT context (through nf_ct_iterate_cleanup), but for some
reason this doesn't happen (perhaps something else is still holding
refs to those entries?).
When ipv4_net_exit is called, conntrack entries (including those
with NAT context) are cleaned up, but the
nat_bysource hashtable is long gone - freed in nf_nat_net_exit. The
bug happens when attempting to free a conntrack entry whose NAT hash
'prev' field points to a slot in the freed hash table (head for that
bin).
We ignore conntracks with null nat bindings. But this is wrong,
as these are in bysource hash table as well.
Restore nat-cleaning for the netns-is-being-removed case.
netfilter: nf_tables: fix wrong type in transaction when replacing rules
In b380e5c ("netfilter: nf_tables: add message type to transactions"),
I used the wrong message type in the rule replacement case. The rule
that is replaced needs to be handled as a deleted rule.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nf_tables: use u32 for chain use counter
Since 4fefee5 ("netfilter: nf_tables: allow to delete several objects
from a batch"), every new rule bumps the chain use counter. However,
this is limited to 16 bits, which means that it will overrun after
2^16 rules.
Use a u32 chain counter and check for overflows (just like we do for
table objects).
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: ctnetlink: fix refcnt leak in dying/unconfirmed list dumper
'last' keeps track of the ct that had its refcnt bumped during previous
dump cycle. Thus it must not be overwritten until end-of-function.
Another (unrelated, theoretical) issue: Don't attempt to bump refcnt of a conntrack
whose reference count is already 0. Such conntrack is being destroyed
right now, its memory is freed once we release the percpu dying spinlock.
Fixes: b7779d06 ('netfilter: conntrack: spinlock per cpu to protect special lists.') Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: ctnetlink: fix dumping of dying/unconfirmed conntracks
The dumping prematurely stops, it seems the callback argument that
indicates that all entries have been dumped is set after iterating
on the first cpu list. The dumping also may stop before the entire
per-cpu list content is also dumped.
With this patch, conntrack -L dying now shows the dying list content
again.
Fixes: b7779d06 ("netfilter: conntrack: spinlock per cpu to protect special lists.") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
1) Fix checksumming regressions, from Tom Herbert.
2) Undo unintentional permissions changes for SCTP rto_alpha and
rto_beta sysfs knobs, from Denial Borkmann.
3) VXLAN, like other IP tunnels, should advertize it's encapsulation
size using dev->needed_headroom instead of dev->hard_header_len.
From Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: sctp: fix permissions for rto_alpha and rto_beta knobs
vxlan: Checksum fixes
net: add skb_pop_rcv_encapsulation
udp: call __skb_checksum_complete when doing full checksum
net: Fix save software checksum complete
net: Fix GSO constants to match NETIF flags
udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
vxlan: use dev->needed_headroom instead of dev->hard_header_len
MAINTAINERS: update cxgb4 maintainer
Linus Torvalds [Mon, 16 Jun 2014 02:02:20 +0000 (16:02 -1000)]
Merge tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux
Pull more clock framework updates from Mike Turquette:
"This contains the second half the of the clk changes for 3.16.
They are simply fixes and code refactoring for the OMAP clock drivers.
The sunxi clock driver changes include splitting out the one
mega-driver into several smaller pieces and adding support for the A31
SoC clocks"
* tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
clk: sunxi: document PRCM clock compatible strings
clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
clk: sun6i: Protect SDRAM gating bit
clk: sun6i: Protect CPU clock
clk: sunxi: Rework clock protection code
clk: sunxi: Move the GMAC clock to a file of its own
clk: sunxi: Move the 24M oscillator to a file of its own
clk: sunxi: Remove calls to clk_put
clk: sunxi: document new A31 USB clock compatible
clk: sunxi: Implement A31 USB clock
ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
CLK: TI: gate: add composite interface clock to OMAP2 only build
ARM: OMAP2: clock: add DT boot support for cpufreq_ck
CLK: TI: OMAP2: add clock init support
...
Pull NVMe update from Matthew Wilcox:
"Mostly bugfixes again for the NVMe driver. I'd like to call out the
exported tracepoint in the block layer; I believe Keith has cleared
this with Jens.
We've had a few reports from people who're really pounding on NVMe
devices at scale, hence the timeout changes (and new module
parameters), hotplug cpu deadlock, tracepoints, and minor performance
tweaks"
[ Jens hadn't seen that tracepoint thing, but is ok with it - it will
end up going away when mq conversion happens ]
* git://git.infradead.org/users/willy/linux-nvme: (22 commits)
NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
NVMe: Use Log Page constants in SCSI emulation
NVMe: Define Log Page constants
NVMe: Fix hot cpu notification dead lock
NVMe: Rename io_timeout to nvme_io_timeout
NVMe: Use last bytes of f/w rev SCSI Inquiry
NVMe: Adhere to request queue block accounting enable/disable
NVMe: Fix nvme get/put queue semantics
NVMe: Delete NVME_GET_FEAT_TEMP_THRESH
NVMe: Make admin timeout a module parameter
NVMe: Make iod bio timeout a parameter
NVMe: Prevent possible NULL pointer dereference
NVMe: Fix the buffer size passed in GetLogPage(CDW10.NUMD)
NVMe: Update data structures for NVMe 1.2
NVMe: Enable BUILD_BUG_ON checks
NVMe: Update namespace and controller identify structures to the 1.1a spec
NVMe: Flush with data support
NVMe: Configure support for block flush
NVMe: Add tracepoints
NVMe: Protect against badly formatted CQEs
...
Daniel Borkmann [Sat, 14 Jun 2014 22:59:14 +0000 (00:59 +0200)]
net: sctp: fix permissions for rto_alpha and rto_beta knobs
Commit 3fd091e73b81 ("[SCTP]: Remove multiple levels of msecs
to jiffies conversions.") has silently changed permissions for
rto_alpha and rto_beta knobs from 0644 to 0444. The purpose of
this was to discourage users from tweaking rto_alpha and
rto_beta knobs in production environments since they are key
to correctly compute rtt/srtt.
RFC4960 under section 6.3.1. RTO Calculation says regarding
rto_alpha and rto_beta under rule C3 and C4:
[...]
C3) When a new RTT measurement R' is made, set
Note: The value of SRTT used in the update to RTTVAR
is its value before updating SRTT itself using the
second assignment. After the computation, update
RTO <- SRTT + 4 * RTTVAR.
C4) When data is in flight and when allowed by rule C5
below, a new RTT measurement MUST be made each round
trip. Furthermore, new RTT measurements SHOULD be
made no more than once per round trip for a given
destination transport address. There are two reasons
for this recommendation: First, it appears that
measuring more frequently often does not in practice
yield any significant benefit [ALLMAN99]; second,
if measurements are made more often, then the values
of RTO.Alpha and RTO.Beta in rule C3 above should be
adjusted so that SRTT and RTTVAR still adjust to
changes at roughly the same rate (in terms of how many
round trips it takes them to reflect new values) as
they would if making only one measurement per
round-trip and using RTO.Alpha and RTO.Beta as given
in rule C3. However, the exact nature of these
adjustments remains a research issue.
[...]
While it is discouraged to adjust rto_alpha and rto_beta
and not further specified how to adjust them, the RFC also
doesn't explicitly forbid it, but rather gives a RECOMMENDED
default value (rto_alpha=3, rto_beta=2). We have a couple
of users relying on the old permissions before they got
changed. That said, if someone really has the urge to adjust
them, we could allow it with a warning in the log.
Fixes: 3fd091e73b81 ("[SCTP]: Remove multiple levels of msecs to jiffies conversions.") Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Cc: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 15 Jun 2014 08:00:56 +0000 (01:00 -0700)]
Merge branch 'csum_fixes'
Tom Herbert says:
====================
Fixes related to some recent checksum modifications.
- Fix GSO constants to match NETIF flags
- Fix logic in saving checksum complete in __skb_checksum_complete
- Call __skb_checksum_complete from UDP if we are checksumming over
whole packet in order to save checksum.
- Fixes to VXLAN to work correctly with checksum complete
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 15 Jun 2014 06:24:28 +0000 (23:24 -0700)]
net: add skb_pop_rcv_encapsulation
This function is used by UDP encapsulation protocols in RX when
crossing encapsulation boundary. If ip_summed is set to
CHECKSUM_UNNECESSARY and encapsulation is not set, change to
CHECKSUM_NONE since the checksum has not been validated within the
encapsulation. Clears csum_valid by the same rationale.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 15 Jun 2014 06:24:20 +0000 (23:24 -0700)]
udp: call __skb_checksum_complete when doing full checksum
In __udp_lib_checksum_complete check if checksum is being done over all
the data (len is equal to skb->len) and if it is call
__skb_checksum_complete instead of __skb_checksum_complete_head. This
allows checksum to be saved in checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 15 Jun 2014 06:24:03 +0000 (23:24 -0700)]
net: Fix save software checksum complete
Geert reported issues regarding checksum complete and UDP.
The logic introduced in commit 7e3cead5172927732f51fde
("net: Save software checksum complete") is not correct.
This patch:
1) Restores code in __skb_checksum_complete_header except for setting
CHECKSUM_UNNECESSARY. This function may be calculating checksum on
something less than skb->len.
2) Adds saving checksum to __skb_checksum_complete. The full packet
checksum 0..skb->len is calculated without adding in pseudo header.
This value is saved in skb->csum and then the pseudo header is added
to that to derive the checksum for validation.
3) In both __skb_checksum_complete_header and __skb_checksum_complete,
set skb->csum_valid to whether checksum of zero was computed. This
allows skb_csum_unnecessary to return true without changing to
CHECKSUM_UNNECESSARY which was done previously.
4) Copy new csum related bits in __copy_skb_header.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 15 Jun 2014 06:23:52 +0000 (23:23 -0700)]
net: Fix GSO constants to match NETIF flags
Joseph Gasparakis reported that VXLAN GSO offload stopped working with
i40e device after recent UDP changes. The problem is that the
SKB_GSO_* bits are out of sync with the corresponding NETIF flags. This
patch fixes that. Also, we add BUILD_BUG_ONs in net_gso_ok for several
GSO constants that were missing to avoid the problem in the future.
Reported-by: Joseph Gasparakis <joseph.gasparakis@intel.com> Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 15 Jun 2014 00:49:48 +0000 (19:49 -0500)]
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is just a couple of drivers (hpsa and lpfc) that got left out for
further testing in linux-next. We also have one fix to a prior
submission (qla2xxx sparse)"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (36 commits)
qla2xxx: fix sparse warnings introduced by previous target mode t10-dif patch
lpfc: Update lpfc version to driver version 10.2.8001.0
lpfc: Fix ExpressLane priority setup
lpfc: mark old devices as obsolete
lpfc: Fix for initializing RRQ bitmap
lpfc: Fix for cleaning up stale ring flag and sp_queue_event entries
lpfc: Update lpfc version to driver version 10.2.8000.0
lpfc: Update Copyright on changed files from 8.3.45 patches
lpfc: Update Copyright on changed files
lpfc: Fixed locking for scsi task management commands
lpfc: Convert runtime references to old xlane cfg param to fof cfg param
lpfc: Fix FW dump using sysfs
lpfc: Fix SLI4 s abort loop to process all FCP rings and under ring_lock
lpfc: Fixed kernel panic in lpfc_abort_handler
lpfc: Fix locking for postbufq when freeing
lpfc: Fix locking for lpfc_hba_down_post
lpfc: Fix dynamic transitions of FirstBurst from on to off
hpsa: fix handling of hpsa_volume_offline return value
hpsa: return -ENOMEM not -1 on kzalloc failure in hpsa_get_device_id
hpsa: remove messages about volume status VPD inquiry page not supported
...
Linus Torvalds [Sun, 15 Jun 2014 00:48:43 +0000 (19:48 -0500)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull more btrfs updates from Chris Mason:
"This has a few fixes since our last pull and a new ioctl for doing
btree searches from userland. It's very similar to the existing
ioctl, but lets us return larger items back down to the app"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix error handling in create_pending_snapshot
btrfs: fix use of uninit "ret" in end_extent_writepage()
btrfs: free ulist in qgroup_shared_accounting() error path
Btrfs: fix qgroups sanity test crash or hang
btrfs: prevent RCU warning when dereferencing radix tree slot
Btrfs: fix unfinished readahead thread for raid5/6 degraded mounting
btrfs: new ioctl TREE_SEARCH_V2
btrfs: tree_search, search_ioctl: direct copy to userspace
btrfs: new function read_extent_buffer_to_user
btrfs: tree_search, copy_to_sk: return needed size on EOVERFLOW
btrfs: tree_search, copy_to_sk: return EOVERFLOW for too small buffer
btrfs: tree_search, search_ioctl: accept varying buffer
btrfs: tree_search: eliminate redundant nr_items check
Al Viro [Sat, 14 Jun 2014 06:12:41 +0000 (07:12 +0100)]
fix __swap_writepage() compile failure on old gcc versions
Tetsuo Handa wrote:
"Commit 62a8067a7f35 ("bio_vec-backed iov_iter") introduced an unnamed
union inside a struct which gcc-4.4.7 cannot handle. Name the unnamed
union as u in order to fix build failure"
Let's do this instead: there is only one place in the entire tree that
steps into this breakage. Anon structs and unions work in older gcc
versions; as the matter of fact, we have those in the tree - see e.g.
struct ieee80211_tx_info in include/net/mac80211.h
What doesn't work is handling their initializers:
struct {
int a;
union {
int b;
char c;
};
} x[2] = {{.a = 1, .c = 'a'}, {.a = 0, .b = 1}};
is the obvious syntax for initializer, perfectly fine for C11 and
handled correctly by gcc-4.7 or later.
Earlier versions, though, break on it - declaration is fine and so's
access to fields (i.e. x[0].c = 'a'; would produce the right code), but
members of the anon structs and unions are not inserted into the right
namespace. Tellingly, those older versions will not barf on struct {int
a; struct {int a;};}; - looks like they just have it hacked up somewhere
around the handling of . and -> instead of doing the right thing.
The easiest way to deal with that crap is to turn initialization of
those fields (in the only place where we have such initializer of
iov_iter) into plain assignment.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 14 Jun 2014 21:51:25 +0000 (14:51 -0700)]
Merge tag 'hsi-for-3.16-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi
Pull HSI build fixes from Sebastian Reichel:
- tighten dependency between ssi-protocol and omap-ssi to fix build
failures with randconfig.
- use normal module refcounting in omap driver to fix build with
disabled module support
* tag 'hsi-for-3.16-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi:
hsi: omap_ssi_port: use normal module refcounting
HSI: fix omap ssi driver dependency
Linus Torvalds [Sat, 14 Jun 2014 21:46:29 +0000 (14:46 -0700)]
Merge branch 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 vdso fixes from Peter Anvin:
"Fixes for x86/vdso.
One is a simple build fix for bigendian hosts, one is to make "make
vdso_install" work again, and the rest is about working around a bug
in Google's Go language -- two are documentation patches that improves
the sample code that the Go coders took, modified, and broke; the
other two implements a workaround that keeps existing Go binaries from
segfaulting at least"
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vdso: Fix vdso_install
x86/vdso: Hack to keep 64-bit Go programs working
x86/vdso: Add PUT_LE to store little-endian values
x86/vdso/doc: Make vDSO examples more portable
x86/vdso/doc: Rename vdso_test.c to vdso_standalone_test_x86.c
x86, vdso: Remove one final use of htole16()
Linus Torvalds [Sat, 14 Jun 2014 21:43:23 +0000 (14:43 -0700)]
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for Sensirion SHTC1 humidity / temperature sensor
- convert ltc4151 and vexpress drivers to use devm functions
- drop generic chip detection from lm85 driver
- avoid forward declarations in atxp1 driver
- fix sign extensions in ina2xx driver
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: vexpress: Use devm helper for hwmon device registration
hwmon: (atxp1) Avoid forward declaration
hwmon: add support for Sensirion SHTC1 sensor
hwmon: (ltc4151) Convert to devm_hwmon_device_register_with_groups
hwmon: (lm85) Drop generic detection
hwmon: (ina2xx) Cast to s16 on shunt and current regs
Eric Dumazet [Thu, 12 Jun 2014 23:13:06 +0000 (16:13 -0700)]
udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
Its too easy to add thousand of UDP sockets on a particular bucket,
and slow down an innocent multicast receiver.
Early demux is supposed to be an optimization, we should avoid spending
too much time in it.
It is interesting to note __udp4_lib_demux_lookup() only tries to
match first socket in the chain.
10 is the threshold we already have in __udp4_lib_lookup() to switch
to secondary hash.
Fixes: 421b3885bf6d5 ("udp: ipv4: Add udp early demux") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: David Held <drheld@google.com> Cc: Shawn Bohrer <sbohrer@rgmadvisors.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Thu, 12 Jun 2014 18:53:10 +0000 (11:53 -0700)]
vxlan: use dev->needed_headroom instead of dev->hard_header_len
When we mirror packets from a vxlan tunnel to other device,
the mirror device should see the same packets (that is, without
outer header). Because vxlan tunnel sets dev->hard_header_len,
tcf_mirred() resets mac header back to outer mac, the mirror device
actually sees packets with outer headers
Vxlan tunnel should set dev->needed_headroom instead of
dev->hard_header_len, like what other ip tunnels do. This fixes
the above problem.
Cc: "David S. Miller" <davem@davemloft.net> Cc: stephen hemminger <stephen@networkplumber.org> Cc: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: Cong Wang <cwang@twopensource.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Lutomirski [Thu, 12 Jun 2014 15:28:10 +0000 (08:28 -0700)]
x86/vdso: Fix vdso_install
"make vdso_install" installs unstripped versions of the vdso objects
for the benefit of the debugger. This was broken by checkin:
6f121e548f83 x86, vdso: Reimplement vdso.so preparation in build-time C
The filenames are different now, so update the Makefile to cope.
This still installs the 64-bit vdso as vdso64.so. We believe this
will be okay, as the only known user is a patched gdb which is known
to use build-ids, but if it turns out to be a problem we may have to
add a link.
Dan McLeran [Fri, 6 Jun 2014 14:27:27 +0000 (08:27 -0600)]
NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
This patch contains several fixes for Scsi START_STOP_UNIT. The previous
code did not account for signed vs. unsigned arithmetic which resulted
in an invalid lowest power state caculation when the device only supports
1 power state.
The code for Power Condition == 2 (Idle) was not following the spec. The
spec calls for setting the device to specific power states, depending
upon Power Condition Modifier, without accounting for the number of
power states supported by the device.
The code for Power Condition == 3 (Standby) was using a hard-coded '0'
which is replaced with the macro POWER_STATE_0.
Signed-off-by: Dan McLeran <daniel.mcleran@intel.com> Reviewed-by: Vishal Verma <vishal.l.verma@linux.intel.com> Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Eric Sandeen [Thu, 12 Jun 2014 05:53:44 +0000 (00:53 -0500)]
btrfs: fix error handling in create_pending_snapshot
fcebe456 cut and pasted some code to a later point
in create_pending_snapshot(), but didn't switch
to the appropriate error handling for this stage
of the function.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Chris Mason <clm@fb.com>
Eric Sandeen [Thu, 12 Jun 2014 05:39:58 +0000 (00:39 -0500)]
btrfs: fix use of uninit "ret" in end_extent_writepage()
If this condition in end_extent_writepage() is false:
if (tree->ops && tree->ops->writepage_end_io_hook)
we will then test an uninitialized "ret" at:
ret = ret < 0 ? ret : -EIO;
The test for ret is for the case where ->writepage_end_io_hook
failed, and we'd choose that ret as the error; but if
there is no ->writepage_end_io_hook, nothing sets ret.
Initializing ret to 0 should be sufficient; if
writepage_end_io_hook wasn't set, (!uptodate) means
non-zero err was passed in, so we choose -EIO in that case.
Signed-of-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Chris Mason <clm@fb.com>
Filipe Manana [Thu, 12 Jun 2014 01:47:37 +0000 (02:47 +0100)]
Btrfs: fix qgroups sanity test crash or hang
Often when running the qgroups sanity test, a crash or a hang happened.
This is because the extent buffer the test uses for the root node doesn't
have an header level explicitly set, making it have a random level value.
This is a problem when it's not zero for the btrfs_search_slot() calls
the test ends up doing, resulting in crashes or hangs such as the following:
Wang Shilong [Wed, 11 Jun 2014 02:55:22 +0000 (10:55 +0800)]
Btrfs: fix unfinished readahead thread for raid5/6 degraded mounting
Steps to reproduce:
# mkfs.btrfs -f /dev/sd[b-f] -m raid5 -d raid5
# mkfs.ext4 /dev/sdc --->corrupt one of btrfs device
# mount /dev/sdb /mnt -o degraded
# btrfs scrub start -BRd /mnt
This is because readahead would skip missing device, this is not true
for RAID5/6, because REQ_GET_READ_MIRRORS return 1 for RAID5/6 block
mapping. If expected data locates in missing device, readahead thread
would not call __readahead_hook() which makes event @rc->elems=0
wait forever.
Fix this problem by checking return value of btrfs_map_block(),we
can only skip missing device safely if there are several mirrors.
Signed-off-by: Wang Shilong <wangsl.fnst@cn.fujitsu.com> Signed-off-by: Chris Mason <clm@fb.com>
Gerhard Heift [Thu, 30 Jan 2014 15:24:03 +0000 (16:24 +0100)]
btrfs: new ioctl TREE_SEARCH_V2
This new ioctl call allows the user to supply a buffer of varying size in which
a tree search can store its results. This is much more flexible if you want to
receive items which are larger than the current fixed buffer of 3992 bytes or
if you want to fetch more items at once. Items larger than this buffer are for
example some of the type EXTENT_CSUM.
Signed-off-by: Gerhard Heift <Gerhard@Heift.Name> Signed-off-by: Chris Mason <clm@fb.com> Acked-by: David Sterba <dsterba@suse.cz>
Keith Busch [Wed, 11 Jun 2014 17:51:35 +0000 (11:51 -0600)]
NVMe: Fix hot cpu notification dead lock
There is a potential dead lock if a cpu event occurs during nvme probe
since it registered with hot cpu notification. This fixes the race by
having the module register with notification outside of probe rather
than have each device register.
The actual work is done in a scheduled work queue instead of in the
notifier since assigning IO queues has the potential to block if the
driver creates additional queues.
Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Linus Torvalds [Fri, 13 Jun 2014 14:42:49 +0000 (07:42 -0700)]
Merge tag 'sound-fix-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Most of changes are small and easy cleanup or fixes:
- a few HD-audio Realtek codec fixes and quirks
- Intel HDMI audio fixes for Broadwell and Haswell / ValleyView
- FireWire sound stack cleanups
- a couple of sequencer core fixes
- compress ABI fix for 64bit
- conversion to modern ktime*() API"
* tag 'sound-fix-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (23 commits)
ALSA: hda/realtek - Add more entry for enable HP mute led
ALSA: hda - Add quirk for external mic on Lifebook U904
ALSA: hda - fix a fixup value for codec alc293 in the pin_quirk table
ALSA: intel8x0: Use ktime and ktime_get()
ALSA: core: Use ktime_get_ts()
ALSA: hda - verify pin:converter connection on unsol event for HSW and VLV
ALSA: compress: Cancel the optimization of compiler and fix the size of struct for all platform.
ALSA: hda - Add quirk for ABit AA8XE
Revert "ALSA: hda - mask buggy stream DMA0 for Broadwell display controller"
ALSA: hda - using POS_FIX_LPIB on Broadwell HDMI Audio
ALSA: hda/realtek - Add support of ALC667 codec
ALSA: hda/realtek - Add more codec rename
ALSA: hda/realtek - New vendor ID for ALC233
ALSA: hda - add two new pin tables
ALSA: hda/realtek - Add support of ALC891 codec
ALSA: seq: Continue broadcasting events to ports if one of them fails
ALSA: bebob: Remove unused function prototype
ALSA: fireworks: Remove meaningless mutex_destroy()
ALSA: fireworks: Remove a constant over width to which it's applied
ALSA: fireworks: Improve comments about Fireworks transaction
...
Linus Torvalds [Fri, 13 Jun 2014 14:39:39 +0000 (07:39 -0700)]
Merge branch 'serge-next-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sergeh/linux-security
Pull more security layer updates from Serge Hallyn:
"A few more commits had previously failed to make it through
security-next into linux-next but this week made it into linux-next.
At least commit "ima: introduce ima_kernel_read()" was deemed critical
by Mimi to make this merge window.
This is a temporary tree just for this request. Mimi has pointed me
to some previous threads about keeping maintainer trees at the
previous release, which I'll certainly do for anything long-term,
after talking with James"
* 'serge-next-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sergeh/linux-security:
ima: introduce ima_kernel_read()
evm: prohibit userspace writing 'security.evm' HMAC value
ima: check inode integrity cache in violation check
ima: prevent unnecessary policy checking
evm: provide option to protect additional SMACK xattrs
evm: replace HMAC version with attribute mask
ima: prevent new digsig xattr from being replaced
Johan Hedberg [Fri, 13 Jun 2014 07:22:28 +0000 (10:22 +0300)]
Bluetooth: Fix locking of hdev when calling into SMP code
The SMP code expects hdev to be unlocked since e.g. crypto functions
will try to (re)lock it. Therefore, we need to release the lock before
calling into smp.c from mgmt.c. Without this we risk a deadlock whenever
the smp_user_confirm_reply() function is called.
Jukka Taimisto [Thu, 12 Jun 2014 10:15:13 +0000 (10:15 +0000)]
Bluetooth: Fix deadlock in l2cap_conn_del()
A deadlock occurs when PDU containing invalid SMP opcode is received on
Security Manager Channel over LE link and conn->pending_rx_work worker
has not run yet.
When LE link is created l2cap_conn_ready() is called and before
returning it schedules conn->pending_rx_work worker to hdev->workqueue.
Incoming data to SMP fixed channel is handled by l2cap_recv_frame()
which calls smp_sig_channel() to handle the SMP PDU. If
smp_sig_channel() indicates failure l2cap_conn_del() is called to delete
the connection. When deleting the connection, l2cap_conn_del() purges
the pending_rx queue and calls flush_work() to wait for the
pending_rx_work worker to complete.
Since incoming data is handled by a worker running from the same
workqueue as the pending_rx_work is being scheduled on, we will deadlock
on waiting for pending_rx_work to complete.
This patch fixes the deadlock by calling cancel_work_sync() instead of
flush_work().
Signed-off-by: Jukka Taimisto <jtt@codenomicon.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
Johan Hedberg [Tue, 10 Jun 2014 11:05:59 +0000 (14:05 +0300)]
Bluetooth: Reuse hci_stop_discovery function when cleaning up HCI state
When cleaning up the HCI state as part of the power-off procedure we can
reuse the hci_stop_discovery() function instead of explicitly sending
HCI command related to discovery. The added benefit of this is that it
takes care of canceling name resolving and inquiry which were not
previously covered by the code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
Johan Hedberg [Tue, 10 Jun 2014 11:05:58 +0000 (14:05 +0300)]
Bluetooth: Refactor discovery stopping into its own function
We'll need to reuse the same logic for stopping discovery also when
cleaning up HCI state when powering off. This patch refactors the code
out to its own function that can later (in a subsequent patch) be used
also for the power off case.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
Johan Hedberg [Tue, 10 Jun 2014 11:05:57 +0000 (14:05 +0300)]
Bluetooth: Fix indicating discovery state when canceling inquiry
When inquiry is canceled through the HCI_Cancel_Inquiry command there is
no Inquiry Complete event generated. Instead, all we get is the command
complete for the HCI_Inquiry_Cancel command. This means that we must
call the hci_discovery_set_state() function from the respective command
complete handler in order to ensure that user space knows the correct
discovery state.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
Johan Hedberg [Tue, 10 Jun 2014 12:19:50 +0000 (15:19 +0300)]
Bluetooth: Fix setting correct authentication information for SMP STK
When we store the STK in slave role we should set the correct
authentication information for it. If the pairing is producing a HIGH
security level the STK is considered authenticated, and otherwise it's
considered unauthenticated. This patch fixes the value passed to the
hci_add_ltk() function when adding the STK on the slave side.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Tested-by: Marcin Kraglak <marcin.kraglak@tieto.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
Johan Hedberg [Mon, 9 Jun 2014 11:41:25 +0000 (14:41 +0300)]
Bluetooth: Add clarifying comment for conn->auth_type
When responding to an IO capability request when we're the initiators of
the pairing we will not yet have the remote IO capability information.
Since the conn->auth_type variable is treated as an "absolute"
requirement instead of a hint of what's needed later in the user
confirmation request handler it's important that it doesn't have the
MITM bit set if there's any chance that the remote device doesn't have
the necessary IO capabilities.
This patch adds a clarifying comment so that conn->auth_type is left
untouched in this scenario.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Mon, 9 Jun 2014 10:58:14 +0000 (13:58 +0300)]
Bluetooth: Fix SSP acceptor just-works confirmation without MITM
From the Bluetooth Core Specification 4.1 page 1958:
"if both devices have set the Authentication_Requirements parameter to
one of the MITM Protection Not Required options, authentication stage 1
shall function as if both devices set their IO capabilities to
DisplayOnly (e.g., Numeric comparison with automatic confirmation on
both devices)"
So far our implementation has done user confirmation for all just-works
cases regardless of the MITM requirements, however following the
specification to the word means that we should not be doing confirmation
when neither side has the MITM flag set.
Johan Hedberg [Tue, 10 Jun 2014 06:54:24 +0000 (09:54 +0300)]
Bluetooth: Fix check for connection encryption
The conn->link_key variable tracks the type of link key in use. It is
set whenever we respond to a link key request as well as when we get a
link key notification event.
These two events do not however always guarantee that encryption is
enabled: getting a link key request and responding to it may only mean
that the remote side has requested authentication but not encryption. On
the other hand, the encrypt change event is a certain guarantee that
encryption is enabled. The real encryption state is already tracked in
the conn->link_mode variable through the HCI_LM_ENCRYPT bit.
This patch fixes a check for encryption in the hci_conn_auth function to
use the proper conn->link_mode value and thereby eliminates the chance
of a false positive result.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
The src_type member of struct hci_conn should always reflect the address
type of the src_member. It should never be overridden. There is already
code in place in the command status handler of HCI_LE_Create_Connection
to copy the right initiator address into conn->init_addr_type.
Without this patch, if privacy is enabled, we will send the wrong
address type in the SMP identity address information PDU (it'll e.g.
contain our public address but a random address type).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
ALSA: hda - Add quirk for external mic on Lifebook U904
According to the bug reporter (Данило Шеган), the external mic
starts to work and has proper jack detection if only pin 0x19
is marked properly as an external headset mic.
AlsaInfo at https://bugs.launchpad.net/ubuntu/+source/pulseaudio/+bug/1328587/+attachment/4128991/+files/AlsaInfo.txt
Hui Wang [Fri, 13 Jun 2014 01:23:10 +0000 (09:23 +0800)]
ALSA: hda - fix a fixup value for codec alc293 in the pin_quirk table
The fixup value for codec alc293 was set to
ALC269_FIXUP_DELL1_MIC_NO_PRESENCE by a mistake, if we don't fix it,
the Dock mic will be overwriten by the headset mic, this will make
the Dock mic can't work.
Cc: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
projects / linux-beck.git / log