Andy Shevchenko [Fri, 5 Sep 2014 15:32:18 +0000 (18:32 +0300)]
rose: use %*ph specifier
Instead of dereference each byte let's use %*ph specifier in the printk()
calls.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: remove obsolete comment about TCP_SKB_CB(skb)->when in tcp_fragment()
The TCP_SKB_CB(skb)->when field no longer exists as of recent change 7faee5c0d514 ("tcp: remove TCP_SKB_CB(skb)->when"). And in any case,
tcp_fragment() is called on already-transmitted packets from the
__tcp_retransmit_skb() call site, so copying timestamps of any kind
in this spot is quite sensible.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Reported-by: Yuchung Cheng <ycheng@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Todd Fujinaka [Fri, 29 Aug 2014 06:43:13 +0000 (06:43 +0000)]
igb: add flags to set eee advertisement mode
Change e1000_set_eee and e1000_set_eee_i35(0|4) to allow
changes in the advertised EEE speeds from ethtool. Adds two boolean
flags to e1000_set_eee_i35(0|4) to pass in advertised speed data.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixed many errors/warnings and checks in e1000_ethtool.c reported
by checkpatch.pl. Suggestions from Joe Perches and Alexander Duyck
applied as well
Signed-off-by: Krzysztof Majzerowicz-Jaszcz <cristos@vipserv.org> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Colin Ian King [Fri, 5 Sep 2014 13:26:11 +0000 (14:26 +0100)]
mISDN: remove DSP_NEVER_DEFINED and adjust code identation
The DSP_NEVER_DEFINED #ifdef is confusing, it slips in an
extra } which is not required because the previous code is
indented incorrectly. Correct the identation and remove the
extraneous DSP_NEVER_DEFINED
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 5 Sep 2014 22:33:32 +0000 (15:33 -0700)]
tcp: introduce TCP_SKB_CB(skb)->tcp_tw_isn
TCP_SKB_CB(skb)->when has different meaning in output and input paths.
In output path, it contains a timestamp.
In input path, it contains an ISN, chosen by tcp_timewait_state_process()
Lets add a different name to ease code comprehension.
Note that 'when' field will disappear in following patch,
as skb_mstamp already contains timestamp, the anonymous
union will promptly disappear as well.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 6 Sep 2014 00:47:12 +0000 (17:47 -0700)]
Merge branch 'eth_get_headlen'
Alexander Duyck says:
====================
net: Drop get_headlen functions in favor of generic function
This series replaces the igb_get_headlen and ixgbe_get_headlen functions
with a generic function named eth_get_headlen.
I have done some performance testing on ixgbe with 258 byte frames since
the calls are only used on frames larger than 256 bytes and have seen no
significant difference in CPU utilization.
v2: renamed __skb_get_poff to skb_get_poff
renamed ___skb_get_poff to __skb_get_poff
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 5 Sep 2014 23:22:18 +0000 (19:22 -0400)]
ixgbe: use new eth_get_headlen interface
Update ixgbe to drop the ixgbe_get_headlen function in favor of eth_get_headlen.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 5 Sep 2014 23:20:43 +0000 (19:20 -0400)]
igb: use new eth_get_headlen interface
Update igb to drop the igb_get_headlen function in favor of eth_get_headlen.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 5 Sep 2014 23:20:26 +0000 (19:20 -0400)]
net: Add function for parsing the header length out of linear ethernet frames
This patch updates some of the flow_dissector api so that it can be used to
parse the length of ethernet buffers stored in fragments. Most of the
changes needed were to __skb_get_poff as it needed to be updated to support
sending a linear buffer instead of a skb.
I have split __skb_get_poff into two functions, the first is skb_get_poff
and it retains the functionality of the original __skb_get_poff. The other
function is __skb_get_poff which now works much like __skb_flow_dissect in
relation to skb_flow_dissect in that it provides the same functionality but
works with just a data buffer and hlen instead of needing an skb.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 6 Sep 2014 00:43:54 +0000 (17:43 -0700)]
Merge branch 'timestamping'
Alexander Duyck says:
====================
This change makes it so that the core path for the phy timestamping logic
is shared between skb_tx_tstamp and skb_complete_tx_timestamp. In addition
it provides a means of using the same skb clone type path in non phy
timestamping drivers.
The main motivation for this is to enable non-phy drivers to be able to
manipulate tx timestamp skbs for such things as putting them in lists or
setting aside buffer in the context block.
v2: Incorporated suggested changes from Willem de Bruijn and Eric Dumazet
dropped uneeded comment
restored order of hwtstamp vs swtstamp
added destructor for skb
Dropped usage of skb_complete_tx_timestamp as a kfree_skb w/ destructor
v3: Updated destructor handling and dealt with socket reference counting issues
v4: Split out combining destructors into a separate patch
====================
Alexander Duyck [Thu, 4 Sep 2014 17:32:11 +0000 (13:32 -0400)]
net: merge cases where sock_efree and sock_edemux are the same function
Since sock_efree and sock_demux are essentially the same code for non-TCP
sockets and the case where CONFIG_INET is not defined we can combine the
code or replace the call to sock_edemux in several spots. As a result we
can avoid a bit of unnecessary code or code duplication.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 4 Sep 2014 17:31:35 +0000 (13:31 -0400)]
net-timestamp: Make the clone operation stand-alone from phy timestamping
The phy timestamping takes a different path than the regular timestamping
does in that it will create a clone first so that the packets needing to be
timestamped can be placed in a queue, or the context block could be used.
In order to support these use cases I am pulling the core of the code out
so it can be used in other drivers beyond just phy devices.
In addition I have added a destructor named sock_efree which is meant to
provide a simple way for dropping the reference to skb exceptions that
aren't part of either the receive or send windows for the socket, and I
have removed some duplication in spots where this destructor could be used
in place of sock_edemux.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 4 Sep 2014 17:31:10 +0000 (13:31 -0400)]
net-timestamp: Merge shared code between phy and regular timestamping
This change merges the shared bits that exist between skb_tx_tstamp and
skb_complete_tx_timestamp. By doing this we can avoid the two diverging as
there were already changes pushed into skb_tx_tstamp that hadn't made it
into the other function.
In addition this resolves issues with the fact that
skb_complete_tx_timestamp was included in linux/skbuff.h even though it was
only compiled in if phy timestamping was enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A buffer is incorrectly zeroed to the length of the pointer. If
cfg_payload_len < sizeof(void *) this can overwrites unrelated memory.
The buffer contents are never read, so no need to zero.
Fixes: 8fe2f761cae9 ("net-timestamp: expand documentation") Reported-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 4 Sep 2014 11:11:23 +0000 (14:11 +0300)]
hyperv: NULL dereference on error
We try to call free_netvsc_device(net_device) when "net_device" is NULL.
It leads to an Oops.
Fixes: f90251c8a6d0 ('hyperv: Increase the buffer length for netvsc_channel_cb()') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 6 Sep 2014 00:21:06 +0000 (17:21 -0700)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-09-04
This series contains updates to i40e, i40evf, ixgbe and ixgbevf.
Catherine adds dual speed module support to i40e. Updates i40e to allow
the user to change link settings when the link is down.
Serey renames i40e_ndo_set_vf_spoofck() to i40e_ndo_set_vf_spookchk()
to be more consistent with what is defined in netdev and removes a
unnecessary variable assignment.
Jesse makes a malicious driver detection warning only print if extended
driver string is enabled for i40e. Fixes a panic under traffic load when
resetting or if/whenever there was a Tx-timeout because we were enabling
the Tx queue to early.
Anjali fixes an issue when PF reset fails, where we were trying to restart
the admin queue which has not been setup at that point. This resolves an
occasional kernel panic when PF reset fails for some reason.
Ethan Zhao replaces the use of a local i40e_vfs_are_assigned() with the
global kernel pci_vfs_assigned() for i40e.
Alex cleans up the FDB handling for ixgbe. This change makes it so that
the behavior for FDB handling is consistent between both the SR-IOV and
non-SR-IOV cases. The main change is that we perform bounds checking on
the number of SR-IOV addresses regardless of if SR-IOV is enabled or not
as we can only support a certain number of addresses in the hardware.
Emil extends the pending Tx work check to the VF interfaces, where the
driver initiates a reset of the interface on link loss with pending Tx
work in order to clear the rings. Introduces a delay for 82599 VFs of
at least 500 usecs to make sure the VFLINKS value is correct, since this
bit tends to flap when a DA or SFP+ cable is disconnected.
Jacob adds code comments in ixgbe to make it more obvious that we are
resetting features based on the fact that we do not have MSI-X enabled,
and cannot use the previous settings. Also resolves a kernel NULL
pointer dereference by limiting the combined total of MACVLAN and
SR-IOV VFs, since the hardware has a limited number of pools available
(64). Previously, no checks were in place to limit the number of
accelerated MACVLAN devices based on the number of pools, which would
be ok since there was already a limit for these well below the number of
available pools. However, SR-IOV uses the very same pools, therefore
we need to ensure that the total number of pools does not exceed the
number of pools available in the hardware.
v2:
- clean up code comment in patch 5 by replacing "an" with "auto
negotiation" based on feedback from Sergei Shtylyov
- removed un-necessary parenthesis around function call in patch 8
based on feedback from Sergei Shtylyov
====================
Daniel Mack [Thu, 4 Sep 2014 07:00:23 +0000 (09:00 +0200)]
net: ethernet: cpsw: improve interrupt lookup logic in cpsw_probe()
Simplify the interrupt resource lookup code in cpsw_probe() by the
following:
* Only look at the first member of the resource. As the driver only
works for DT-enabled platforms anyway, a resource of type
IORESOURCE_IRQ will only contain one single entry
(res->start == res->end), so there is no need for the iteration.
* Add a bounds check to avoid overflows if we are passed more than
ARRAY_SIZE(priv->irqs_table) resources.
* Assign 'ret' with the return value of devm_request_irq() so that
cpsw_probe() returns the appropriate error code.
* If devm_request_irq() fails, report the error code in the log
message.
Signed-off-by: Daniel Mack <zonque@gmail.com> Acked-by: Mugunthan V N <mugunthanvnm@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 4 Sep 2014 05:21:56 +0000 (22:21 -0700)]
ipv4: fix a race in update_or_create_fnhe()
nh_exceptions is effectively used under rcu, but lacks proper
barriers. Between kzalloc() and setting of nh->nh_exceptions(),
we need a proper memory barrier.
Signed-off-by: Eric Dumazet <edumazet@google.com> Fixes: 4895c771c7f00 ("ipv4: Add FIB nexthop exceptions.") Signed-off-by: David S. Miller <davem@davemloft.net>
The following series of patches includes fixes/updates to the driver.
- Query the device for the actual speed mode (KR/KX) rather than trying
to track it
- Update parallel detection logic to support KR mode
- Fix new warnings from checkpatch in the amd-xgbe and amd-xgbe-phy
driver
This patch series is based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
amd-xgbe-phy: Check device for current speed mode (KR/KX)
Since device resets can change the current mode it's possible to think
the device is in a different mode than it actually is. Rather than
trying to determine every place that is needed to set/save the current
mode, be safe and check the devices actual mode when needed rather than
trying to track it.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
r8152: change the location of rtl8152_set_mac_address
Exchange the location of rtl8152_set_mac_address() and
set_ethernet_addr(). Then, the set_ethernet_addr() could
set the MAC address by calling rtl8152_set_mac_address()
later.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 5 Sep 2014 19:12:32 +0000 (12:12 -0700)]
Merge branch 'rx_copybreak'
Govindarajulu Varadarajan says:
====================
enic: Add support for rx_copybreak
The following series implements rx_copybreak.
dma_map_single()/dma_unmap_single() is more expensive than alloc_skb & memcpy
for smaller packets. By doing this we can reuse the dma buff which is already
mapped. This is very useful when iommu is on. The default skb copybreak value
is 256.
When iommu is on, we can go much higher than 256. All the drivers that supports
rx_copybreak provides module parameter to change this value. Since module
parameter is the least preferred way for changing driver values, this series
adds ethtool support for setting rx_copybreak.
v4:
Validate tunable length in ethtool_get_tunable, not in driver implemented
function.
Loose tunable_ops array for each tunable type. Define one function and let the
driver use switch case for each type.
Use double underscore for data type in UAPI headers.
Use const qualifier where possible.
v3:
Add tunable namespace to ethtool. Use new ethtool cmd ETHTOOL_S/GTUNABLE to
set/get rx_copybreak from userspace.
v2:
Add new ethtool_cmd for DMA buffer parameters, instead of adding new members to
existing ethtool_ringparam.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling dma_map_single()/dma_unmap_single() is quite expensive compared
to copying a small packet. So let's copy short frames and keep the buffers
mapped.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Marcel reported to see the following message when autoloading
is being triggered when adding nlmon device:
Loading kernel module for a network device with
CAP_SYS_MODULE (deprecated). Use CAP_NET_ADMIN and alias
netdev-nlmon instead.
This false-positive happens despite with having correct
capabilities set, e.g. through issuing `ip link del dev nlmon`
more than once on a valid device with name nlmon, but Marcel
has also seen it on creation time when no nlmon module is
previously compiled-in or loaded as module and the device
name equals a link type name (e.g. nlmon, vxlan, team).
Stephen says:
The netdev module alias is a hold over from the past. For
normal devices, people used to create a alias eth0 to and
point it to the type of network device used, that was back
in the bad old ISA days before real discovery.
Also, the tunnels create module alias for the control device
and ip used to use this to autoload the tunnel device.
The message is bogus and should just be removed, I also see
it in a couple of other cases where tap devices are renamed
for other usese.
As mentioned in 8909c9ad8ff0 ("net: don't allow CAP_NET_ADMIN
to load non-netdev kernel modules"), we nevertheless still
might want to leave the old autoloading behaviour in place
as it could break old scripts, so for now, lets just remove
the log message as Stephen suggests.
Reference: http://thread.gmane.org/gmane.linux.kernel/1105168 Reported-by: Marcel Holtmann <marcel@holtmann.org> Suggested-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Cc: Vasiliy Kulikov <segoon@openwall.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Tue, 2 Sep 2014 20:53:44 +0000 (22:53 +0200)]
net: bpf: make eBPF interpreter images read-only
With eBPF getting more extended and exposure to user space is on it's way,
hardening the memory range the interpreter uses to steer its command flow
seems appropriate. This patch moves the to be interpreted bytecode to
read-only pages.
In case we execute a corrupted BPF interpreter image for some reason e.g.
caused by an attacker which got past a verifier stage, it would not only
provide arbitrary read/write memory access but arbitrary function calls
as well. After setting up the BPF interpreter image, its contents do not
change until destruction time, thus we can setup the image on immutable
made pages in order to mitigate modifications to that code. The idea
is derived from commit 314beb9bcabf ("x86: bpf_jit_comp: secure bpf jit
against spraying attacks").
This is possible because bpf_prog is not part of sk_filter anymore.
After setup bpf_prog cannot be altered during its life-time. This prevents
any modifications to the entire bpf_prog structure (incl. function/JIT
image pointer).
Every eBPF program (including classic BPF that are migrated) have to call
bpf_prog_select_runtime() to select either interpreter or a JIT image
as a last setup step, and they all are being freed via bpf_prog_free(),
including non-JIT. Therefore, we can easily integrate this into the
eBPF life-time, plus since we directly allocate a bpf_prog, we have no
performance penalty.
Tested with seccomp and test_bpf testsuite in JIT/non-JIT mode and manual
inspection of kernel_page_tables. Brad Spengler proposed the same idea
via Twitter during development of this patch.
Joint work with Hannes Frederic Sowa.
Suggested-by: Brad Spengler <spender@grsecurity.net> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Alexei Starovoitov <ast@plumgrid.com> Cc: Kees Cook <keescook@chromium.org> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: systemport: update UMAC_CMD only when link is detected
When we bring the interface down, phy_stop() will schedule the PHY
state machine to call our link adjustment callback. By the time we do so,
we may have clock gated off the SYSTEMPORT hardware block, and this will
cause bus errors to happen in bcm_sysport_adj_link():
Make sure that we only touch the UMAC_CMD register when there is an
actual link. This is safe to do for two reasons:
- updating the Ethernet MAC registers only make sense when a physical
link is present
- the PHY library state machine first set phydev->link = 0 before
invoking phydev->adjust_link in the PHY_HALTED case
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4: implement igmp_qrv sysctl to tune igmp robustness variable
As in IPv6 people might increase the igmp query robustness variable to
make sure unsolicited state change reports aren't lost on the network. Add
and document this new knob to igmp code.
RFCs allow tuning this parameter back to first IGMP RFC, so we also use
this setting for all counters, including source specific multicast.
Also take over sysctl value when upping the interface and don't reuse
the last one seen on the interface.
Cc: Flavio Leitner <fbl@redhat.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Flavio Leitner <fbl@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: add sysctl_mld_qrv to configure query robustness variable
This patch adds a new sysctl_mld_qrv knob to configure the mldv1/v2 query
robustness variable. It specifies how many retransmit of unsolicited mld
retransmit should happen. Admins might want to tune this on lossy links.
Also reset mld state on interface down/up, so we pick up new sysctl
settings during interface up event.
IPv6 certification requests this knob to be available.
I didn't make this knob netns specific, as it is mostly a setting in a
physical environment and should be per host.
Cc: Flavio Leitner <fbl@redhat.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Flavio Leitner <fbl@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Thu, 21 Aug 2014 06:17:59 +0000 (06:17 +0000)]
ixgbe: limit combined total of macvlan and SR-IOV VFs
Hardware has a limited number of pools available (64). Previously, no
checks were in place to limit the number of accelerated macvlan devices
based on the number of pools. Normally this would be ok, because there
was already a limit for these well below the number of available pools.
However, SR-IOV uses the very same pools. Therefor, we need to ensure
that the total number of pools (number of VFs plus the number of non-VF
pools in use for accelerated macvlans) does not exceed the number of
pools available in hardware.
This patch resolves a kernel NULL pointer dereference caused by the following commands:
Cc: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Thu, 21 Aug 2014 06:16:55 +0000 (06:16 +0000)]
ixgbe: add comment noting recalculation of queues
Since we previously called ixgbe_set_num_queues just prior to attempting
to set our interrupt scheme, it may be non obvious why we have to call
it again inside the function. Add a comment which helps make it more
obvious that we are resetting features based on the fact that we do not
have MSI-X enabled, and cannot use the previous settings.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Wed, 13 Aug 2014 05:52:13 +0000 (05:52 +0000)]
ixgbevf: introduce delay for checking VFLINKS on 82599
VFLINKS.LINKUP bit tends to flap when a DA or SFP+ cable is disconnected.
It can take up to 500 usecs for the LINKUP bit to be correct.
This patch resolves the issue by introducing a delay for 82599 VFs of at
least 500 usecs to make sure the VFLINKS value is correct.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Tue, 12 Aug 2014 07:12:08 +0000 (07:12 +0000)]
ixgbe: reset interface on link loss with pending Tx work from the VF
ixgbe initiates a reset of the interface on link loss with pending Tx work
in order to clear the rings.
This patch extends the pending Tx work check to the VF interfaces with the
same purpose.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Thu, 17 Jul 2014 02:11:22 +0000 (02:11 +0000)]
ixgbe: Cleanup FDB handling code
This change makes it so that the behavior for FDB handling is consistent
between both the SR-IOV and non-SR-IOV cases. The main change here is that we
perform bounds checking on the number of SR-IOV addresses regardless of if
SR-IOV is enabled or not as we can only support a certain number of addresses
in the hardware.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e version to 1.0.11 and i40evf version to 1.0.5.
Change-ID: I63a60fa2efe82aae87a8a3095f43218db57d46ce Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com> Tested-by: Jim Young <jamesx.m.young@intel.com>
Jesse Brandeburg [Tue, 12 Aug 2014 06:33:14 +0000 (06:33 +0000)]
i40e: fix panic due to too-early Tx queue enable
This fixes the panic under traffic load when resetting. This issue
could also show up if/whenever there is a Tx-timeout.
Change-ID: Ie393a1f17fd5d962e56fc3bfe784899ef25402f5 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Jim Young <jamesx.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We shouldn't restart Admin queue subtask if PF reset fails since we do
not have the AQ setup at that point. This patch makes sure we disable AQ
clean subtask when PF reset fails.
This will resolve an occasional kernel panic when PF reset fails for
some reason.
Change-ID: I11a747773362a8c5c0ad7a10cd34be0bda8eb9e8 Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Tested-by: Jim Young <jamesx.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver is un-necessarily printing a warning that is only marginally
useful to the user. Make the warning only print if extended driver
string printing is enabled, other messages related to a reset event
will still continue to print.
Change-ID: I5e8beca6516a2f176cd2e72b0ac2b3b909e6c953 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Jim Young <jamesx.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e: Tell OS link is going down when calling set_phy_config
Since we don't seem to be getting an LSE telling us link is going down
during set_phy_config (but we do get an LSE telling us we are coming
back up), fake one for the OS and tell them link is going down. Also
do an atomic restart no matter what because there are times the user
may want to end with link up even if they started with link down (like
if they accidentally set it to a speed that can't link and are trying to
fix it).
Change-ID: I0a642af9c1d0feb67bce741aba1a9c33bd349ed6 Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com> Tested-by: Jim Young <jamesx.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Serey Kong [Tue, 29 Jul 2014 04:03:53 +0000 (04:03 +0000)]
i40e: Remove unnecessary assignment
Remove unnecessary setting of "ret" variable as it's already set at
the top of the function.
Change-ID: Icaccfc67f335817a23579b7c43625d59ad6c9925 Signed-off-by: Serey Kong <serey.kong@intel.com> Tested-by: Jim Young <jamesx.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Serey Kong [Sat, 12 Jul 2014 07:28:14 +0000 (07:28 +0000)]
i40e: Change wording to be more consistent
Change "spoofck" to "spoofchk" to be consistent with as defined in netdev.
Change-ID: I9866d6284cb5f92c8d71dc0776c6d1e71dfb62a5 Signed-off-by: Serey Kong <serey.kong@intel.com> Tested-by: Jim Young <jamesx.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e: Allow user to change link settings if link is down
Allow the user to change auto-negotiation and speed settings if
link is down.
Change-ID: I372967c627682b5e1835f623a7cbf41b21b51043 Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com> Tested-by: Jim Young <jamesx.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that fw has implemented dual speed module support, we can add ours.
Also, add the phy type for 1G LR/SR and set its media type to fiber.
Lastly, instead of a WARN_ON if the phy type is not recognized just print
a warning.
Change-ID: I2e5227d4a8c2907b0ed423038e5dbce774e466b0 Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com> Tested-by: Jim Young <jamesx.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rick Jones [Wed, 3 Sep 2014 16:18:00 +0000 (09:18 -0700)]
mlx4_en: Convert the normal skb free path to dev_consume_skb_any()
It would appear the mlx4_en driver was still making a call to
dev_kfree_skb_any() where dev_consume_skb_any() would be more
appropriate. This should make dropped packet profiling/tracking
easier/better over a NIC driven by mlx4_en.
Signed-off-by: Rick Jones <rick.jones2@hp.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
lib/rhashtable: allow user to set the minimum shifts of shrinking
Although rhashtable library allows user to specify a quiet big size
for user's created hash table, the table may be shrunk to a
very small size - HASH_MIN_SIZE(4) after object is removed from
the table at the first time. Subsequently, even if the total amount
of objects saved in the table is quite lower than user's initial
setting in a long time, the hash table size is still dynamically
adjusted by rhashtable_shrink() or rhashtable_expand() each time
object is inserted or removed from the table. However, as
synchronize_rcu() has to be called when table is shrunk or
expanded by the two functions, we should permit user to set the
minimum table size through configuring the minimum number of shifts
according to user specific requirement, avoiding these expensive
actions of shrinking or expanding because of calling synchronize_rcu().
Signed-off-by: Ying Xue <ying.xue@windriver.com> Acked-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
qdisc: validate frames going through the direct_xmit path
In commit 50cbe9ab5f8d ("net: Validate xmit SKBs right when we
pull them out of the qdisc") the validation code was moved out of
dev_hard_start_xmit and into dequeue_skb.
However this overlooked the fact that we do not always enqueue
the skb onto a qdisc. First situation is if qdisc have flag
TCQ_F_CAN_BYPASS and qdisc is empty. Second situation is if
there is no qdisc on the device, which is a common case for
software devices.
Originally spotted and inital patch by Alexander Duyck.
As a result Alex was seeing issues trying to connect to a
vhost_net interface after commit 50cbe9ab5f8d was applied.
Added a call to validate_xmit_skb() in __dev_xmit_skb(), in the
code path for qdiscs with TCQ_F_CAN_BYPASS flag, and in
__dev_queue_xmit() when no qdisc.
Also handle the error situation where dev_hard_start_xmit() could
return a skb list, and does not return dev_xmit_complete(rc) and
falls through to the kfree_skb(), in that situation it should
call kfree_skb_list().
Fixes: 50cbe9ab5f8d ("net: Validate xmit SKBs right when we pull them out of the qdisc") Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qdisc: exit case fixes for skb list handling in qdisc layer
More minor fixes to merge commit 53fda7f7f9e (Merge branch 'xmit_list')
that allows us to work with a list of SKBs.
Fixing exit cases in qdisc_reset() and qdisc_destroy(), where a
leftover requeued SKB (qdisc->gso_skb) can have the potential of
being a skb list, thus use kfree_skb_list().
This is a followup to commit 10770bc2d1 ("qdisc: adjustments for
API allowing skb list xmits").
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 2 Sep 2014 19:46:04 +0000 (12:46 -0700)]
Merge branch 'be2net-next'
Sathya Perla says:
====================
be2net: patch set
v2 changes: add a new line after variable declaration in patch 12.
***
Patch 1 adds a few new log messages to help debugging in failure cases.
Patch 2 uses new macros for parsing RX/TX completions and TX wrbs to
help shorten the lines.
Patch 3 adds a description for the RX counter rx_input_fifo_overflow_drop.
Patch 4 adds TX completion error statistics reporting via ethtool.
Patch 5 adds a dma_mapping_error counter and its reporting via ethtool.
Patch 6 fixes up log messages in the Lancer FW download path.
Patch 7 replaces gotos with direct return statements.
Patch 8 cleans up be_change_mtu() code by using a new macro BE_MAX_MTU
Patch 9 makes be_cmd_get_regs() routine to return an integer status
similar to other FW cmd routines in be_cmds.c
Patch 10 gets rid of TX budget as enforcing a budget on TX completion
processing in NAPI is neither suggested nor it provides a performance benefit.
Patch 11 defines and uses a new macro for_all_tx_queues_on_eq() similar
to the RX processing code.
Patch 12 queries max_tx_qs from the FW for BE3 super-nic profiles.
For those profiles, the driver cannot assume a constant BE3_MAX_TX_QS value,
as the value may change for each function.
Please consider applying this patch set to the net-next tree. Thanks!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
be2net: query max_tx_qs for BE3 super-nic profile from FW
In the BE3 super-nic profile, the max_tx_qs value can vary for each function.
So the driver needs to query this value from FW instead of using the
pre-defined constant BE3_MAX_TX_QS.
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the for() loop that traverses all the TX queues on an EQ
with the macro for_all_tx_queues_on_eq(). With this expalnatory
name, the one line comment is not required anymore.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few failure cases in be_cmd_get_regs() that ideally must return
an error value. This style is used across all the routines in be_cmds.c with
this routine being an exception. This patch fixes this.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kalesh AP [Tue, 2 Sep 2014 04:26:53 +0000 (09:56 +0530)]
be2net: define BE_MAX_MTU
This patch defines a new macro BE_MAX_MTU to make the code in be_change_mtu()
more readable.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kalesh AP [Tue, 2 Sep 2014 04:26:52 +0000 (09:56 +0530)]
be2net: remove unncessary gotos
In cases where there is no extra code to handle an error, this patch replaces
gotos with a direct return statement.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kalesh AP [Tue, 2 Sep 2014 04:26:51 +0000 (09:56 +0530)]
be2net: fix log messages in lancer FW download path
Log messages in the Lancer FW download path have issues such as:
- a single message spanning multiple lines
- the success message is logged even in failure cases
- status codes are already logged in the FW cmd routines
This patch fixes these issues.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
be2net: Add a dma_mapping_error counter in ethtool
Add a dma_mapping_error counter to count the number of packets dropped
due to DMA mapping errors.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kalesh AP [Tue, 2 Sep 2014 04:26:49 +0000 (09:56 +0530)]
be2net: Add TX completion error statistics in ethtool
HW reports TX completion errors in TX completion. This patch adds these
counters to ethtool statistics.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The AMAP_GET/SET_BITS() macro calls take structure name as a parameter
and hence are long and span more than one line. Replace these calls
with a wrapper macros for RX/Tx compls and TX wrb. This results in fewer
lines and more readable code in be_main.c
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the following log messages to help debugging
failure cases:
1) log FW version number: this is useful when driver initialization
fails and the FW version number cannot be queried via ethtool
2) per function resource limits for BEx chips: these values are
currently being printed only for Skyhawk and Lancer
3) PCI BAR mapping failure
4) function_mode/caps queried from FW: this helps catch any FW bugs
that could advertise wrong capabilities to the driver
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sk->sk_error_queue is dequeued in four locations. All share the
exact same logic. Deduplicate.
Also collapse the two critical sections for dequeue (at the top of
the recv handler) and signal (at the bottom).
This moves signal generation for the next packet forward, which should
be harmless.
It also changes the behavior if the recv handler exits early with an
error. Previously, a signal for follow-up packets on the errqueue
would then not be scheduled. The new behavior, to always signal, is
arguably a bug fix.
For rxrpc, the change causes the same function to be called repeatedly
for each queued packet (because the recv handler == sk_error_report).
It is likely that all packets will fail for the same reason (e.g.,
memory exhaustion).
This code runs without sk_lock held, so it is not safe to trust that
sk->sk_err is immutable inbetween releasing q->lock and the subsequent
test. Introduce int err just to avoid this potential race.
Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 2 Sep 2014 04:36:35 +0000 (21:36 -0700)]
Merge branch 'csums-next'
Tom Herbert says:
====================
net: Checksum offload changes - Part VI
I am working on overhauling RX checksum offload. Goals of this effort
are:
- Specify what exactly it means when driver returns CHECKSUM_UNNECESSARY
- Preserve CHECKSUM_COMPLETE through encapsulation layers
- Don't do skb_checksum more than once per packet
- Unify GRO and non-GRO csum verification as much as possible
- Unify the checksum functions (checksum_init)
- Simplify code
What is in this seventh patch set:
- Add skb->csum. This allows a device or GRO to indicate that an
invalid checksum was detected.
- Checksum unncessary to checksum complete conversions.
With these changes, I believe that the third goal of the overhaul is
now mostly achieved. In the case of no encapsulation or one layer of
encapsulation, there should only be at most one skb_checksum over
each packet (between GRO and normal path). In the case of two layers
of encapsulation, it is still possible with the right combination of
non-zero and zero UDP checksums to have >1 skb_checksum. For instance:
IP>GRE(with csum)>IP>UDP(zero csum)>VXLAN>IP>UDP(non-zero csum),
would likely necessiate an skb_checksum in GRO and normal path.
This doesn't seem like a common scenario at all so I'm inclined to
not address this now, if multiple layers of encapsulation becomes
popular we can reassess.
Note that checksum conversion shows a nice improvement for RX VXLAN when
outer UDP checksum is enabled (12.65% CPU compared to 20.94%). This
is not only from the fact that we don't need checksum calculation on
the host, but also allows GRO for VXLAN in this case. Checksum
conversion does not help send side (which still needs to perform
a checksum on host). For that we will implement remote checksum offload
in a later patch
(http://tools.ietf.org/html/draft-herbert-remotecsumoffload-00).
Please review carefully and test if possible, mucking with basic
checksum functions is always a little precarious :-)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 31 Aug 2014 22:12:44 +0000 (15:12 -0700)]
gre: Add support for checksum unnecessary conversions
Call skb_checksum_try_convert and skb_gro_checksum_try_convert
after checksum is found present and validated in the GRE header
for normal and GRO paths respectively.
In GRO path, call skb_gro_checksum_try_convert
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 31 Aug 2014 22:12:43 +0000 (15:12 -0700)]
udp: Add support for doing checksum unnecessary conversion
Add support for doing CHECKSUM_UNNECESSARY to CHECKSUM_COMPLETE
conversion in UDP tunneling path.
In the normal UDP path, we call skb_checksum_try_convert after locating
the UDP socket. The check is that checksum conversion is enabled for
the socket (new flag in UDP socket) and that checksum field is
non-zero.
In the UDP GRO path, we call skb_gro_checksum_try_convert after
checksum is validated and checksum field is non-zero. Since this is
already in GRO we assume that checksum conversion is always wanted.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 31 Aug 2014 22:12:42 +0000 (15:12 -0700)]
net: Infrastructure for checksum unnecessary conversions
For normal path, added skb_checksum_try_convert which is called
to attempt to convert CHECKSUM_UNNECESSARY to CHECKSUM_COMPLETE. The
primary condition to allow this is that ip_summed is CHECKSUM_NONE
and csum_valid is true, which will be the state after consuming
a CHECKSUM_UNNECESSARY.
For GRO path, added skb_gro_checksum_try_convert which is the GRO
analogue of skb_checksum_try_convert. The primary condition to allow
this is that NAPI_GRO_CB(skb)->csum_cnt == 0 and
NAPI_GRO_CB(skb)->csum_valid is set. This implies that we have consumed
all available CHECKSUM_UNNECESSARY checksums in the GRO path.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 31 Aug 2014 22:12:41 +0000 (15:12 -0700)]
net: Support for csum_bad in skbuff
This flag indicates that an invalid checksum was detected in the
packet. __skb_mark_checksum_bad helper function was added to set this.
Checksums can be marked bad from a driver or the GRO path (the latter
is implemented in this patch). csum_bad is checked in
__skb_checksum_validate_complete (i.e. calling that when ip_summed ==
CHECKSUM_NONE).
csum_bad works in conjunction with ip_summed value. In the case that
ip_summed is CHECKSUM_NONE and csum_bad is set, this implies that the
first (or next) checksum encountered in the packet is bad. When
ip_summed is CHECKSUM_UNNECESSARY, the first checksum after the last
one validated is bad. For example, if ip_summed == CHECKSUM_UNNECESSARY,
csum_level == 1, and csum_bad is set-- then the third checksum in the
packet is bad. In the normal path, the packet will be dropped when
processing the protocol layer of the bad checksum:
__skb_decr_checksum_unnecessary called twice for the good checksums
changing ip_summed to CHECKSUM_NONE so that
__skb_checksum_validate_complete is called to validate the third
checksum and that will fail since csum_bad is set.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/phy/mdio-bcm-unimac.c:195:37-38: unimac_mdio_ids is not NULL
terminated at line 195
Make sure of_device_id tables are NULL terminated
Generated by: scripts/coccinelle/misc/of_table.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 29 Aug 2014 19:42:07 +0000 (12:42 -0700)]
net: dsa: make dsa_pack_type static
net/dsa/dsa.c:624:20: sparse: symbol 'dsa_pack_type' was not declared.
Should it be static?
Fixes: 3e8a72d1dae374 ("net: dsa: reduce number of protocol hooks") Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bonding: add slave_changelink support and use it for queue_id
This patch adds support for slave_changelink to the bonding and uses it
to give the ability to change the queue_id of the enslaved devices via
netlink. It sets slave_maxtype and uses bond_changelink as a prototype for
bond_slave_changelink.
Example/test command after the iproute2 patch:
ip link set eth0 type bond_slave queue_id 10
CC: David S. Miller <davem@davemloft.net> CC: Jay Vosburgh <j.vosburgh@gmail.com> CC: Veaceslav Falico <vfalico@gmail.com> CC: Andy Gospodarek <andy@greyhouse.net> Suggested-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 28 Aug 2014 22:11:03 +0000 (15:11 -0700)]
net: systemport: tell RXCHK if we are using Broadcom tags
When Broadcom tags are enabled, e.g: when interfaced to an Ethernet
switch, make sure that we tell the RXCHK engine that it should be
expecting a 4-bytes Broadcom tag after the Ethernet MAC Source Address.
Use netdev_uses_dsa() to check for that condition since that will tell
us if a switch is attached to our network interface.
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pktgen: add flag NO_TIMESTAMP to disable timestamping
Then testing the TX limits of the stack, then it is useful to
be-able to disable the do_gettimeofday() timetamping on every packet.
This implements a pktgen flag NO_TIMESTAMP which will disable this
call to do_gettimeofday().
The performance change on (my system E5-2695) with skb_clone=0, goes
from TX 2,423,751 pps to 2,567,165 pps with flag NO_TIMESTAMP. Thus,
the cost of do_gettimeofday() or saving is approx 23 nanosec.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log