Russ Dill [Wed, 18 Nov 2009 18:02:13 +0000 (11:02 -0700)]
USB: Close usb_find_interface race
USB drivers that create character devices call usb_register_dev in their
probe function. This associates the usb_interface device with that minor
number and creates the character device and announces it to the world.
However, the driver's probe function is called before the new
usb_interface is added to the driver's klist_devices.
This is a problem because userspace will respond to the character device
creation announcement by opening the character device. The driver's open
function will the call usb_find_interface to find the usb_interface
associated with that minor number. usb_find_interface will walk the
driver's list of devices and find the usb_interface with the matching
minor number.
Because the announcement happens before the usb_interface is added to the
driver's klist_devices, a race condition exists. A straightforward fix
is to walk the list of devices on usb_bus_type instead since the device
is added to that list before the announcement occurs.
bus_find_device calls get_device to bump the reference count on the found
device. It is arguable that the reference count should be dropped by the
caller of usb_find_interface instead of usb_find_interface, however,
the current users of usb_find_interface do not expect this.
USB: handle bcd incrementation in usb modalias generation
This patch fixes a bug when incrementing/decrementing on a BCD formatted
integer (i.e. 0x09++ should be 0x10 not 0x0A). It just adds a function
for incrementing/decrementing BCD integers by converting to decimal,
doing the increment/decrement and then converting back to BCD.
USB: add hex/bcd detection to usb modalias generation
The current code to generate usb modaliases from usb_device_id assumes
that the device's bcdDevice descriptor will actually be in BCD format.
While this should be a sane assumption, some devices don't follow spec
and just use plain old hex. This causes drivers for these devices to
generate invalid modalias lines which will never actually match for the
hardware.
The following patch adds hex support for bcdDevice in file2alias.c by
detecting when a driver uses a hex formatted bcdDevice_(lo|hi) and
adjusts the output to hex format accordingly.
Drivers for devices which have bcdDevice conforming to BCD will have no
change in modalias output. Drivers for devices which don't conform
(i.e. ibmcam) should now generate valid modaliases.
EXAMPLE OUTPUT (ibmcam; space added to highlight change)
Old: usb:v0545p800D d030[10-9] dc*dsc*dp*ic*isc*ip*
New: usb:v0545p800D d030a dc*dsc*dp*ic*isc*ip*
Adrian Taylor [Thu, 19 Nov 2009 10:35:33 +0000 (10:35 +0000)]
USB: Exposing second ACM channel as tty for Nokia S60 phones.
Nokia S60 phones expose two ACM channels. The first is a modem and is picked
up by the standard AT-command interface information in the CDC-ACM driver. The
second is marked as having a vendor-specific protocol. Normally, we don't
expose those as ttys. (On some other devices, they may be claimed by the
rndis_host driver and used as a network interface).
But on S60 this second ACM channel is the way that third-party S60 application
developers are expected to communicate over USB. It acts as a serial device
at the S60 end, and so it should on Linux too.
The list of devices is largely derived from:
http://wiki.forum.nokia.com/index.php/S60_Platform_and_device_identification_codes
http://wiki.forum.nokia.com/index.php/Nokia_USB_Product_IDs
and includes only the S60 3rd Edition+ devices documented there.
There are many devices for which the USB device ID is not documented,
including:
Nokia 6290
Nokia E63
Nokia 5630 XpressMusic
Nokia 5730 XpressMusic
Nokia 6710 Navigator
Nokia 6720 classic
Nokia 6730 Classic
Nokia 6760 slide
Nokia 6790 slide
Nokia 6790 Surge
Nokia E52
Nokia E55
Nokia E71x (AT&T)
Nokia E72
Nokia E75
Nokia E75 US+LTA variant
Nokia N79
Nokia N86 8MP
Nokia 5230 (RM-588)
Nokia 5230 (RM-594)
Nokia 5530 XpressMusic
Nokia 5530 XpressMusic (china)
Nokia 5800 XM
Nokia N97 (RM-506)
Nokia N97 mini
Nokia X6
It would be good to add those subsequently.
Signed-off-by: Adrian Taylor <aat@realvnc.com> Acked-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Larry Finger [Thu, 5 Nov 2009 16:37:03 +0000 (10:37 -0600)]
USB: Check results of dma_map_single
In map_urb_for_dma(), the DMA address returned by dma_map_single()
is not checked to determine if it is legal. This lack of checking
contributed to a problem with the libertas wireless driver
(http://marc.info/?l=linux-wireless&m=125695331205062&w=2). The
difficulty was not detected until the buffer was unmapped. By this time
memory corruption had occurred.
The situation is fixed by testing the returned DMA address, and
returning -EAGAIN if the address is invalid.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 6 Nov 2009 17:32:23 +0000 (12:32 -0500)]
USB: add scatter-gather support to usbmon
This patch (as1301) adds support to usbmon for scatter-gather URBs.
The text interface looks at only the first scatterlist element, since
it never copies more than 32 bytes of data anyway. The binary
interface copies as much data as possible up to the first
non-addressable buffer.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Elina Pasheva [Wed, 4 Nov 2009 18:25:48 +0000 (10:25 -0800)]
USB: serial: sierra driver memory reduction
This patch deals with reducing the memory footprint for sierra driver.
This optimization is aimed for embedded software customers.
Some sierra modems can expose upwards of 7 USB interfaces, each possibly
offering different services. In general, interfaces used for the
exchange of wireless data require much higher throughput, hence require
more memory (i.e. more URBs) than lower performance interfaces. URBs
used for the IN direction are pre-allocated by the driver and this patch
introduces a way to configure the number of IN URBs allocated on a
per-interface basis. Interfaces with lower throughput requirements
receive fewer URBs, thereby reducing the RAM memory consumed by the
driver.
NOTE1: This driver has always pre-allocated URBs for the IN direction.
NOTE2: The number of URBs pre-allocated for the low-performance
interfaces has already been extensively tested in previous versions of
this driver.
We also added the capability to log function calls by adding DEBUG flag.
Please note that this flag is commented out because this is the default
state
for it.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: Interface Association Descriptors added to CDC & RNDIS
Without Interface Association Descriptor, the CDC serial and
RNDIS functions did not work correctly when added to a
composite gadget with other functions. This is because, it
defined two interfaces and some hosts tried to treat each
interface separatelly.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Moved code initialising fsg_common structure to fsg_common_init()
function which is called from fsg_bind(). Moreover, changed
reference counting mechanism: fsg_common has a reference counter
which counts how many fsg_dev structures uses it. When this
reaches zero fsg_common_release() is run which unregisters
LUN devices and frees memory.
fsg_common_init() takes pointer to fsg_common structure as an
argument. If it is NULL function allocates storage otherwise
uses pointed to memory (handy if fsg_common is a field of another
structure or a static variable).
fsg_common_release() will free storage only if
free_storage_on_release is set -- it is initialised by
fsg_common_init(): set if allocation was done, unset
otherwise (one may overwrite it of course).
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using version of fsg_buffhd structure with buf field being an
array of characters with predefined size. Since mass storage
function does not define changing buffer size on run-time it is
not required for the field to be a pointer to void and allocating
space dynamically.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: g_mass_storage: parts of fsg_dev moved to fsg_common structure
In the final version, many fsg_dev structures will (be able to)
refer to a single fsg_common structure and so it is required
to move common data to another object which can be shared.
Situation where many fsg_dev structures refer single fsg_common
structure is when a single instance of MSF is used in several
USB configurations.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: g_mass_storage: testing code from f_mass_storage.c removed
Removed code that was included when CONFIG_USB_FILE_STORAGE_TEST
was defined. If this functionality is required one may still use
the original File-backed Storage Gadget. It has been agreed that
testing functionality is not required in the composite function.
Also removed fsg_suspend() and fsg_resume() which were no
operations.
Moreover, storage_common.c has been modified in such a way that
defining certain macros skips parts of the file. Those macros
are:
* FSG_NO_INTR_EP -- skips interrupt endpoint descriptors
* FSG_NO_DEVICE_STRINGS -- skips certain strings
* FSG_NO_OTG -- skips OTG descriptor
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: g_file_storage: more code from file_storage.c moved to storage_common.c
Since storage_common.c no longer references mod_data object
it is now possible to include it before mod_data object is
defined. This makes it possible to move some defines that
are used as default values of mod_data fields to be defined
in storage_common.c file (where they should be set from
the beginning).
Also, show_ro(), show_file(), store_ro() and store_file()
have been moved to storage_common.c with LUN's device's
drvdata changed from pointing to fsg_dev to pointing to
rw_semaphore (&fsg->filesem).
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: g_file_storage: per-LUN ro, removable and cdrom flags handling changed
removable and cdrom flag has been added to the fsg_lun structure
removing any references to mod_data object from storage_common.c.
As of read-only flag, previously it was set if a read-only
backing file was specified (which is good) and remained set
even after the file has been closed (which may be considered an
issue). Currently, the initial read-only flag is preserved so
if it was unset each time file is opened code will try to open
it read-write even if previous file was opened read-only.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: g_file_storage: "fsg_" prefix added to some identifiers
Prefixed some identifiers that were defined in storage_common.c file
with "fsg_". Not all identifiers were prefixed but the ones that are
most likely to produce conflicts when used with other USB functions.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: g_file_storage: parts of file_storage.c moved to separate file
Moved parts of the file_storage.c file which do not reference fsg_dev
structure to newly created storage_common.c file. dump_msg() and
dump_cdb() have been changed to macros to remove fsg_dev reference.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniel Mack [Wed, 28 Oct 2009 00:14:59 +0000 (01:14 +0100)]
USB: Add EHCI support for MX27 and MX31 based boards
The Freescale MX27 and MX31 SoCs have a EHCI controller onboard.
The controller is capable of USB on the go. This patch adds
a driver to support all three of them.
Users have to pass details about serial interface configuration in the
platform data.
The USB OTG core used here is the ARC core, so the driver should
be renamed and probably be merged with ehci-fsl.c eventually.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Daniel Mack <daniel@caiaq.de> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 27 Oct 2009 19:26:50 +0000 (15:26 -0400)]
USB: fix a bug in the scatter-gather library
This patch (as1298) fixes a bug in the new scatter-gather URB
facility. If an URB uses a scatterlist then it should not have the
URB_NO_INTERRUPT flag set; otherwise the system won't be notified when
the transfer completes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: David Vrabel <david.vrabel@csr.com> CC: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 27 Oct 2009 19:20:13 +0000 (15:20 -0400)]
USB: add a "remove hardware" sysfs attribute
This patch (as1297) adds a "remove" attribute to each USB device's
directory in sysfs. Writing to this attribute causes the device to be
deconfigured (the same as writing 0 to the "bConfigurationValue"
attribute) and then tells the hub driver to disable the device's
upstream port. The device remains locked during these activities so
there is no possibility of it getting reconfigured in between. The
port will remain disabled until after the device is unplugged.
The purpose of this is to provide a means for user programs to imitate
the "Safely remove hardware" applet in Windows. Some devices do
expect their ports to be disabled before they are unplugged, and they
provide visual feedback to users indicating when they can safely be
unplugged.
The security implications are minimal. Writing to the "remove"
attribute is no more dangerous than writing to the
"bConfigurationValue" attribute.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: David Zeuthen <davidz@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 27 Oct 2009 19:18:46 +0000 (15:18 -0400)]
USB: don't use a fixed DMA mapping for hub status URBs
This patch (as1296) gets rid of the fixed DMA-buffer mapping used by
the hub driver for its status URB. This URB doesn't get used much --
mainly when a device is plugged in or unplugged -- so the dynamic
mapping overhead is minimal. And most systems have many fewer
external hubs than root hubs, which don't need a mapped buffer anyway.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Tue, 27 Oct 2009 17:55:05 +0000 (10:55 -0700)]
USB: ehci: Respect IST when scheduling new split iTDs.
The EHCI specification says that an EHCI host controller may cache part of
the isochronous schedule. The EHCI controller must advertise how much it
caches in the schedule through the HCCPARAMS register isochronous
scheduling threshold (IST) bits.
In theory, adding new iTDs within the IST should be harmless. The HW will
follow the old cached linked list and miss the new iTD. SW will notice HW
missed the iTD and return 0 for the transfer length.
However, Intel ICH9 chipsets (and some later chipsets) have issues when SW
attempts to schedule a split transaction within the IST. All transfers
will cease being sent out that port, and the drivers will see isochronous
packets complete with a length of zero. Start of frames may or may not
also disappear, causing the device to go into auto-suspend. This "bus
stall" will continue until a control or bulk transfer is queued to a
device under that roothub.
Most drivers will never cause this behavior, because they use multiple
URBs with multiple packets to keep the bus busy. If you limit the number
of URBs to one, you may be able to hit this bug.
Make sure the EHCI driver does not schedule full-speed transfers within
the IST under an Intel chipset. Make sure that when we fall behind the
current microframe plus IST, we schedule the new transfer at the next
periodic interval after the IST.
Don't change the scheduling for new transfers, since the schedule slop will
always be greater than the IST. Allow high speed isochronous transfers to
be scheduled within the IST, since this doesn't trigger the Intel chipset
bug.
Make sure that if the host caches the full frame, the EHCI driver's
internal isochronous threshold (ehci->i_thresh) is set to
8 microframes + 2 microframes wiggle room. This is similar to what is done in
the case where the host caches less than the full frame.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Tue, 27 Oct 2009 17:54:49 +0000 (10:54 -0700)]
USB: ehci: Minor constant fix for SCHEDULE_SLOP.
Change the constant SCHEDULE_SLOP to be 80 microframes, instead of 10
frames. It was always multiplied by 8 to convert frames to microframes.
SCHEDULE_SLOP is only used in ehci-sched.c.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Tue, 3 Nov 2009 21:06:40 +0000 (13:06 -0800)]
USB: xhci: Remove unused HCD statistics code.
CONFIG_USB_HCD_STAT was used in an abandoned patch to track host
controller throughput statistics. Since CONFIG_USB_HCD_STAT will never be
defined, remove code that can never run.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Tue, 27 Oct 2009 17:57:01 +0000 (10:57 -0700)]
USB: xhci: Add watchdog timer for URB cancellation.
In order to giveback a canceled URB, we must ensure that the xHCI
hardware will not access the buffer in an URB. We can't modify the
buffer pointers on endpoint rings without issuing and waiting for a stop
endpoint command. Since URBs can be canceled in interrupt context, we
can't wait on that command. The old code trusted that the host
controller would respond to the command, and would giveback the URBs in
the event handler. If the hardware never responds to the stop endpoint
command, the URBs will never be completed, and we might hang the USB
subsystem.
Implement a watchdog timer that is spawned whenever a stop endpoint
command is queued. If a stop endpoint command event is found on the
event ring during an interrupt, we need to stop the watchdog timer with
del_timer(). Since del_timer() can fail if the timer is running and
waiting on the xHCI lock, we need a way to signal to the timer that
everything is fine and it should exit. If we simply clear
EP_HALT_PENDING, a new stop endpoint command could sneak in and set it
before the watchdog timer can grab the lock.
Instead we use a combination of the EP_HALT_PENDING flag and a counter
for the number of pending stop endpoint commands
(xhci_virt_ep->stop_cmds_pending). If we need to cancel the watchdog
timer and del_timer() succeeds, we decrement the number of pending stop
endpoint commands. If del_timer() fails, we leave the number of pending
stop endpoint commands alone. In either case, we clear the
EP_HALT_PENDING flag.
The timer will decrement the number of pending stop endpoint commands
once it obtains the lock. If the timer is the tail end of the last stop
endpoint command (xhci_virt_ep->stop_cmds_pending == 0), and the
endpoint's command is still pending (EP_HALT_PENDING is set), we assume
the host is dying. The watchdog timer will set XHCI_STATE_DYING, try to
halt the xHCI host, and give back all pending URBs.
Various other places in the driver need to check whether the xHCI host
is dying. If the interrupt handler ever notices, it should immediately
stop processing events. The URB enqueue function should also return
-ESHUTDOWN. The URB dequeue function should simply return the value
of usb_hcd_check_unlink_urb() and the watchdog timer will take care of
giving the URB back. When a device is disconnected, the xHCI hardware
structures should be freed without issuing a disable slot command (since
the hardware probably won't respond to it anyway). The debugging
polling loop should stop polling if the host is dying.
When a device is disconnected, any pending watchdog timers are killed
with del_timer_sync(). It must be synchronous so that the watchdog
timer doesn't attempt to access the freed endpoint structures.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Tue, 27 Oct 2009 17:56:33 +0000 (10:56 -0700)]
USB: xhci: Re-purpose xhci_quiesce().
xhci_quiesce() is basically a no-op right now. It's only called if
HC_IS_RUNNING() is true, and the body of the function consists of a
BUG_ON if HC_IS_RUNNING() is false. For the new xHCI watchdog timer, we
need a new function that clears the xHCI running bit in the command
register, but doesn't wait for the halt status to show up in the status
register. Re-purpose xhci_quiesce() to do that.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Tue, 27 Oct 2009 17:55:52 +0000 (10:55 -0700)]
USB: xhci: Handle URB cancel, complete and resubmit race.
In the old code, there was a race condition between the stop endpoint
command and the URB submission process. When the stop endpoint command is
handled by the event handler, the endpoint ring is assumed to be stopped.
When a stop endpoint command is queued, URB submissions are to not ring
the doorbell. The old code would check the number of pending URBs to be
canceled, and would not ring the doorbell if it was non-zero.
However, the following race condition could occur with the old code:
1. Cancel an URB, add it to the list of URBs to be canceled, queue the stop
endpoint command, and increment ep->cancels_pending to 1.
2. The URB finishes on the HW, and an event is enqueued to the event ring
(at the same time as 1).
3. The stop endpoint command finishes, and the endpoint is halted. An
event is queued to the event ring.
4. The event handler sees the finished URB, notices it was to be
canceled, decrements ep->cancels_pending to 0, and removes it from the to
be canceled list.
5. The event handler drops the lock and gives back the URB. The
completion handler requeues the URB (or a different driver enqueues a new
URB). This causes the endpoint's doorbell to be rung, since
ep->cancels_pending == 0. The endpoint is now running.
6. A second URB is canceled, and it's added to the canceled list.
Since ep->cancels_pending == 0, a new stop endpoint command is queued, and
ep->cancels_pending is incremented to 1.
7. The event handler then sees the completed stop endpoint command. The
handler assumes the endpoint is stopped, but it isn't. It attempts to
move the dequeue pointer or change TDs to cancel the second URB, while the
hardware is actively accessing the endpoint ring.
To eliminate this race condition, a new endpoint state bit is introduced,
EP_HALT_PENDING. When this bit is set, a stop endpoint command has been
queued, and the command handler has not begun to process the URB
cancellation list yet. The endpoint doorbell should not be rung when this
is set. Set this when a stop endpoint command is queued, clear it when
the handler for that command runs, and check if it's set before ringing a
doorbell. ep->cancels_pending is eliminated, because it is no longer
used.
Make sure to ring the doorbell for an endpoint when the stop endpoint
command handler runs, even if the canceled URB list is empty. All
canceled URBs could have completed and new URBs could have been enqueued
without the doorbell being rung before the command was handled.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniel Mack [Thu, 15 Oct 2009 14:09:34 +0000 (17:09 +0300)]
USB OTG: add support for ulpi connected external transceivers
This adds support for OTG transceivers directly connected to the ULPI
interface. In particular, the following details are added
- a struct for low level io functions (read/write)
- a priv field to be used as 'viewport' by low level access functions
- an (*init) and (*shutdown) callbacks, along with static inline helpers
- a (*set_vbus) callback to switch the port power on and off
- a flags field for per-transceiver settings
- some defines for the flags bitmask to configure platform specific
details
Signed-off-by: Daniel Mack <daniel@caiaq.de> Cc: Heikki Krogerus <ext-heikki.krogerus@nokia.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hong Xu [Fri, 25 Sep 2009 10:24:12 +0000 (12:24 +0200)]
USB: modifications for at91sam9g10
Modify both host and gadget USB drivers for at91sam9g10.
This add a clock management equivalent to at91sam9261 on usb drivers.
It also add the way of handling gadget pull-ups (like the at91sam9261).
Signed-off-by: Hong Xu <hong.xu@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Laurent Pinchart [Tue, 20 Oct 2009 22:03:39 +0000 (00:03 +0200)]
USB audio gadget: handle endpoint control requests at the function level
Now that control requests targeted at an endpoint can be handled at the
function level, move the UAC-specific control request handling code from
the audio gadget driver to the audio function driver.
Laurent Pinchart [Tue, 20 Oct 2009 22:03:38 +0000 (00:03 +0200)]
USB gadget: Handle endpoint requests at the function level
Control requests targeted at an endpoint (that is sent to EP0 but
specifying the target endpoint address in wIndex) are dispatched to the
current configuration's setup callback, requiring all gadget drivers to
dispatch the requests to the correct function driver.
To avoid this, record which endpoints are used by each function in the
composite driver SET CONFIGURATION handler and dispatch requests
targeted at endpoints to the correct function.
David Vrabel [Wed, 14 Oct 2009 13:23:55 +0000 (13:23 +0000)]
USB: whci-hcd: fix type and format warnings in sg code
Fix type and format warning in the new sg code. Remove the very chatty
debug messages that were left in by mistake and use min_t() as required
(no one seems to agree on a type for buffer sizes).
Reported-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David Vrabel <david.vrabel@csr.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Vrabel [Mon, 24 Aug 2009 14:02:27 +0000 (15:02 +0100)]
USB: whci-hcd: support urbs with scatter-gather lists
Support urbs with scatter-gather lists by trying to fit sg list elements
into page lists in one or more qTDs. qTDs must end on a wMaxPacketSize
boundary so if this isn't possible the urb's sg list must be copied into
bounce buffers.
Signed-off-by: David Vrabel <david.vrabel@csr.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Vrabel [Mon, 24 Aug 2009 13:44:30 +0000 (14:44 +0100)]
USB: make urb scatter-gather support more generic
The WHCI HCD will also support urbs with scatter-gather lists. Add a
usb_bus field to indicated how many sg list elements are supported by
the HCD. Use this to decide whether to pass the scatter-list to the HCD
or not.
Make the usb-storage driver use this new field.
Signed-off-by: David Vrabel <david.vrabel@csr.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add bus glue driver for Xilinx USB host controller. The controller can be
configured as HS only or HS/FS hybrid. The driver uses the device tree file
to configure the driver according to the setting in the hardware system.
This driver has been tested with usbtest using the NET2280 PCI card.
Signed-off-by: Julie Zhu <julie.zhu@xilinx.com> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Wilcox [Thu, 24 Sep 2009 22:19:49 +0000 (16:19 -0600)]
USB Storage: Make driver less chatty when it finds a new device
Use dev_dbg() instead of an unconditional printk(KERN_DEBUG). This has
two benefits; one is that it identifies the USB device which the messages
related to, and the other is that the messages won't be produced unless
debug is turned on.
Enable the debug messages when CONFIG_USB_STORAGE_DEBUG is set.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds [Thu, 10 Dec 2009 17:35:02 +0000 (09:35 -0800)]
Merge branch 'bugfix' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen
* 'bugfix' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: try harder to balloon up under memory pressure.
Xen balloon: fix totalram_pages counting.
xen: explicitly create/destroy stop_machine workqueues outside suspend/resume region.
xen: improve error handling in do_suspend.
xen: don't leak IRQs over suspend/resume.
xen: call clock resume notifier on all CPUs
xen: use iret for return from 64b kernel to 32b usermode
xen: don't call dpm_resume_noirq() with interrupts disabled.
xen: register runstate info for boot CPU early
xen: register runstate on secondary CPUs
xen: register timer interrupt with IRQF_TIMER
xen: correctly restore pfn_to_mfn_list_list after resume
xen: restore runstate_info even if !have_vcpu_info_placement
xen: re-register runstate area earlier on resume.
xen: wait up to 5 minutes for device connetion
xen: improvement to wait_for_devices()
xen: fix is_disconnected_device/exists_disconnected_device
xen/xenbus: make DEVICE_ATTR()s static
Linus Torvalds [Thu, 10 Dec 2009 17:34:40 +0000 (09:34 -0800)]
Merge branch 'xen/fbdev' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen
* 'xen/fbdev' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen pvfb: Inhibit VM_IO flag to be set on vmalloc-ed framebuffers.
fb-defio: Inhibit VM_IO flag to be set on vmalloc-ed framebuffers.
fb-defio: If FBINFO_VIRTFB is defined, do not set VM_IO flag.
Fix toogle whether xenbus driver should be built as module or part of kernel.
Linus Torvalds [Thu, 10 Dec 2009 17:33:29 +0000 (09:33 -0800)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (47 commits)
ext4: Fix potential fiemap deadlock (mmap_sem vs. i_data_sem)
ext4: Do not override ext2 or ext3 if built they are built as modules
jbd2: Export jbd2_log_start_commit to fix ext4 build
ext4: Fix insufficient checks in EXT4_IOC_MOVE_EXT
ext4: Wait for proper transaction commit on fsync
ext4: fix incorrect block reservation on quota transfer.
ext4: quota macros cleanup
ext4: ext4_get_reserved_space() must return bytes instead of blocks
ext4: remove blocks from inode prealloc list on failure
ext4: wait for log to commit when umounting
ext4: Avoid data / filesystem corruption when write fails to copy data
ext4: Use ext4 file system driver for ext2/ext3 file system mounts
ext4: Return the PTR_ERR of the correct pointer in setup_new_group_blocks()
jbd2: Add ENOMEM checking in and for jbd2_journal_write_metadata_buffer()
ext4: remove unused parameter wbc from __ext4_journalled_writepage()
ext4: remove encountered_congestion trace
ext4: move_extent_per_page() cleanup
ext4: initialize moved_len before calling ext4_move_extents()
ext4: Fix double-free of blocks with EXT4_IOC_MOVE_EXT
ext4: use ext4_data_block_valid() in ext4_free_blocks()
...
Linus Torvalds [Thu, 10 Dec 2009 17:32:24 +0000 (09:32 -0800)]
Merge branch 'for-linus' of git://git.open-osd.org/linux-open-osd
* 'for-linus' of git://git.open-osd.org/linux-open-osd:
exofs: Multi-device mirror support
exofs: Move all operations to an io_engine
exofs: move osd.c to ios.c
exofs: statfs blocks is sectors not FS blocks
exofs: Prints on mount and unmout
exofs: refactor exofs_i_info initialization into common helper
exofs: dbg-print less
exofs: More sane debug print
trivial: some small fixes in exofs documentation
David Wong [Thu, 3 Dec 2009 13:54:25 +0000 (10:54 -0300)]
V4L/DVB (13592): max2165: 32bit build patch
This patch drops usage of floating point variable for 32bit build
Signed-off-by: David T. L. Wong <davidtlwong@gmail.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Boaz Harrosh [Mon, 16 Nov 2009 14:03:05 +0000 (16:03 +0200)]
exofs: Multi-device mirror support
This patch changes on-disk format, it is accompanied with a parallel
patch to mkfs.exofs that enables multi-device capabilities.
After this patch, old exofs will refuse to mount a new formatted FS and
new exofs will refuse an old format. This is done by moving the magic
field offset inside the FSCB. A new FSCB *version* field was added. In
the future, exofs will refuse to mount unmatched FSCB version. To
up-grade or down-grade an exofs one must use mkfs.exofs --upgrade option
before mounting.
Introduced, a new object that contains a *device-table*. This object
contains the default *data-map* and a linear array of devices
information, which identifies the devices used in the filesystem. This
object is only written to offline by mkfs.exofs. This is why it is kept
separate from the FSCB, since the later is written to while mounted.
Same partition number, same object number is used on all devices only
the device varies.
* define the new format, then load the device table on mount time make
sure every thing is supported.
* Change I/O engine to now support Mirror IO, .i.e write same data
to multiple devices, read from a random device to spread the
read-load from multiple clients (TODO: stripe read)
Implementation notes:
A few points introduced in previous patch should be mentioned here:
* Special care was made so absolutlly all operation that have any chance
of failing are done before any osd-request is executed. This is to
minimize the need for a data consistency recovery, to only real IO
errors.
* Each IO state has a kref. It starts at 1, any osd-request executed
will increment the kref, finally when all are executed the first ref
is dropped. At IO-done, each request completion decrements the kref,
the last one to return executes the internal _last_io() routine.
_last_io() will call the registered io_state_done. On sync mode a
caller does not supply a done method, indicating a synchronous
request, the caller is put to sleep and a special io_state_done is
registered that will awaken the caller. Though also in sync mode all
operations are executed in parallel.
Boaz Harrosh [Sun, 8 Nov 2009 12:54:08 +0000 (14:54 +0200)]
exofs: Move all operations to an io_engine
In anticipation for multi-device operations, we separate osd operations
into an abstract I/O API. Currently only one device is used but later
when adding more devices, we will drive all devices in parallel according
to a "data_map" that describes how data is arranged on multiple devices.
The file system level operates, like before, as if there is one object
(inode-number) and an i_size. The io engine will split this to the same
object-number but on multiple device.
At first we introduce Mirror (raid 1) layout. But at the final outcome
we intend to fully implement the pNFS-Objects data-map, including
raid 0,4,5,6 over mirrored devices, over multiple device-groups. And
more. See: http://tools.ietf.org/html/draft-ietf-nfsv4-pnfs-obj-12
* Define an io_state based API for accessing osd storage devices
in an abstract way.
Usage:
First a caller allocates an io state with:
exofs_get_io_state(struct exofs_sb_info *sbi,
struct exofs_io_state** ios);
And when done
exofs_put_io_state(struct exofs_io_state *ios);
* Convert all source files to use this new API
* Convert from bio_alloc to bio_kmalloc
* In io engine we make use of the now fixed osd_req_decode_sense
There are no functional changes or on disk additions after this patch.
Boaz Harrosh [Tue, 3 Nov 2009 14:46:00 +0000 (16:46 +0200)]
exofs: move osd.c to ios.c
If I do a "git mv" together with a massive code change
and commit in one patch, git looses the rename and
records a delete/new instead. This is bad because I want
a rename recorded so later rebased/cherry-picked patches
to the old name will work. Also the --follow is lost.
Linus Torvalds [Thu, 10 Dec 2009 03:57:06 +0000 (19:57 -0800)]
Merge branch 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPICA: Update version to 20091112.
ACPICA: Add additional module-level code support
ACPICA: Deploy new create integer interface where appropriate
ACPICA: New internal utility function to create Integer objects
ACPICA: Add repair for predefined methods that must return sorted lists
ACPICA: Fix possible fault if return Package objects contain NULL elements
ACPICA: Add post-order callback to acpi_walk_namespace
ACPICA: Change package length error message to an info message
ACPICA: Reduce severity of predefined repair messages, Warning to Info
ACPICA: Update version to 20091013
ACPICA: Fix possible memory leak for Scope ASL operator
ACPICA: Remove possibility of executing _REG methods twice
ACPICA: Add repair for bad _MAT buffers
ACPICA: Add repair for bad _BIF/_BIX packages
Linus Torvalds [Thu, 10 Dec 2009 03:53:11 +0000 (19:53 -0800)]
Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (41 commits)
hwmon: (adt7475) Add VID support for the ADT7476
hwmon: (adt7475) Add an entry in MAINTAINERS
hwmon: (adt7475) Add support for the ADT7476
hwmon: (adt7475) Voltage attenuators can be bypassed
hwmon: (adt7475) Print device information on probe
hwmon: (adt7475) Handle alternative pin functions
hwmon: (adt7475) Move sysfs files removal to a separate function
hwmon: (adt7475) Add support for the ADT7490
hwmon: (adt7475) Improve device detection
hwmon: (adt7475) Add missing static marker
hwmon: (adt7475) Rework voltage inputs handling
hwmon: (adt7475) Implement pwm_use_point2_pwm_at_crit
hwmon: (adt7475) New documentation
hwmon: (adt7475) Add support for the ADT7473
hwmon: (f71882fg) Add support for the f71889fg (version 2)
hwmon: (f71882fg) Fix sysfs file removal
hwmon: (f71882fg) Cleanup sysfs attr creation 2/2
hwmon: (f71882fg) Cleanup sysfs attr creation 1/2
hwmon: (thmc50) Stop using I2C_CLIENT_MODULE_PARM
hwmon: Add Freescale MC13783 ADC driver
...
Linus Torvalds [Thu, 10 Dec 2009 03:52:01 +0000 (19:52 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
Input: appletouch - give up maintainership
Input: dm355evm_kbd - switch to using sparse keymap library
Input: wistron_btns - switch to using sparse keymap library
Input: add generic support for sparse keymaps
Input: fix memory leak in force feedback core
Input: wistron - remove identification strings from DMI table
Input: psmouse - remove identification strings from DMI tables
Input: atkbd - remove identification strings from DMI table
Input: i8042 - remove identification strings from DMI tables
DMI: allow omitting ident strings in DMI tables
Input: psmouse - do not carry DMI data around
Input: matrix-keypad - switch to using dev_pm_ops
Input: keyboard - fix lack of locking when traversing handler->h_list
Input: gpio_keys - scan gpio state at probe and resume time
Input: keyboard - add locking around event handling
Input: usbtouchscreen - add support for ET&T TC5UH touchscreen controller
Input: xpad - add two new Xbox 360 devices
Input: polled device - do not start polling if interval is zero
Input: polled device - schedule first poll immediately
Input: add S3C24XX touchscreen driver
...
Linus Torvalds [Thu, 10 Dec 2009 03:46:12 +0000 (19:46 -0800)]
Merge branch 'next-i2c' of git://git.fluff.org/bjdooks/linux
* 'next-i2c' of git://git.fluff.org/bjdooks/linux: (25 commits)
i2c-pnx: Map I2C adapter number to platform ID number
i2c-omap: OMAP3: PM: (re)init for every transfer to support off-mode
i2c-designware: i2c_dw_handle_tx_abort: Use dev_dbg() for NOACK cases
i2c-designware: Cosmetic cleanups
i2c-designware: Tx abort cleanups
i2c-designware: Skip RX_FULL and TX_EMPTY bits on tx abort errors
i2c-designware: i2c_dw_xfer_msg: Fix error handling procedures
i2c-designware: Disable TX_EMPTY when all i2c_msg msgs has been processed
i2c-designware: Process all i2c_msg messages in the interrupt handler
i2c-designware: i2c_dw_read: Remove redundant target address checker
i2c-designware: i2c_dw_func: Set I2C_FUNC_SMBUS_foo bits
i2c-designware: Initialize byte count variables just prior to being used
i2c-designware: i2c_dw_xfer_msg: Introduce a local "buf" pointer
i2c-designware: Divide i2c_dw_xfer_msg into two functions
i2c-designware: Enable RX_FULL interrupt
i2c-designware: Set Tx/Rx FIFO threshold levels
i2c-designware: Process i2c_msg messages in the interrupt handler
i2c-designware: i2c_dw_xfer_msg: Fix i2c_msg search bug
i2c-designware: Improved _HCNT/_LCNT calculation
i2c-designware: Remove an useless local variable "num"
...
Linus Torvalds [Thu, 10 Dec 2009 03:45:58 +0000 (19:45 -0800)]
Merge branch 's3c24xx-updates' of git://git.fluff.org/bjdooks/linux
* 's3c24xx-updates' of git://git.fluff.org/bjdooks/linux:
ARM: S3C24XX: DMA: Use valid index when accessing array
ARM: S3C: move s3c_pwm_remove to .devexit.text
ARM: S3C24XX: Export s3c24xx_set_fiq for modules.
ARM: S3C: move s3c_adc_remove to .devexit.text
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-next-2.6:
sl82c105: remove no longer needed debugging code
sis5513: remove stale TODO
pdc202xx_old: remove no longer needed debugging code
cy82c693: remove no longer needed debugging code
cmd64x: remove no longer needed debugging code
alim15x3: remove obsolete and dangerous wdc_udma parameter
ide: Increase WAIT_DRQ to accomodate some CF cards and SSD drives.
cs5535: add pci id for AMD based CS5535 controllers
slc90e66: fix UDMA handling
drivers/ide/tx4938ide.c: use resource_size()
drivers/ide/ide_platform.c: use resource_size()
drivers/ide/au1xxx-ide.c: use resource_size()
hpt366: remove dead old timing tables
ide: update Kconfig text to mark as deprecated
ide-tape: remove the BKL
hpt366: kill unused #define's
Linus Torvalds [Thu, 10 Dec 2009 03:43:19 +0000 (19:43 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: add multi-input quirk for NextWindow Touchscreen.
HID: add support for Acan FG-8100 barcode reader
HID: make Media key on Logitech DiNovo Mini work
HID: support Logitech/3DConnexion SpaceTraveler and SpaceNavigator
HID: remove BKL from hiddev_ioctl_usage()
HID: fixup quirk for NCR devices
HID: pidff - fix unnecessary loop iterations on reset
HID: add NOGET quirk for another device from CH Products
HID: remove useless DRIVER_VERSION macro
HID: fix MODULE_AUTHOR usage in HID modules
HID: blacklist Acer Ferrari 4005 optical mouse
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
[SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
[SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
[SCSI] zfcp: Update FSF error reporting
[SCSI] zfcp: Improve ELS ADISC handling
[SCSI] zfcp: Simplify handling of ct and els requests
[SCSI] zfcp: Remove ZFCP_DID_MASK
[SCSI] zfcp: Move WKA port to zfcp FC code
[SCSI] zfcp: Use common code definitions for FC CT structs
[SCSI] zfcp: Use common code definitions for FC ELS structs
[SCSI] zfcp: Update FCP protocol related code
[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
[SCSI] zfcp: Assign scheduled work to driver queue
[SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
[SCSI] zfcp: Implement module unloading
[SCSI] zfcp: Merge trace code for fsf requests in one function
[SCSI] zfcp: Access ports and units with container_of in sysfs code
[SCSI] zfcp: Remove suspend callback
[SCSI] zfcp: Remove global config_mutex
[SCSI] zfcp: Replace local reference counting with common kref
...
Linus Torvalds [Thu, 10 Dec 2009 03:09:42 +0000 (19:09 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: export clk_* symbols in clk.c
m68knommu: Split the .init section into INIT_TEXT_SECTION and INIT_DATA_SECTION.
m68knommu: Move __init_end out of the .init section.
m68knommu: Move __init_begin out of the .init section.
m68knommu: Use more macros inside the .init section.
m68knommu: Use INIT_TASK_DATA and CACHELINE_ALIGNED_DATA.
m68knommu: Make THREAD_SIZE available to assembly files.
m68knommu: Don't hardcode the value of PAGE_SIZE in the linker script.
m68knommu: rename BSS define in linker script
m68knommu: add a task_pt_regs() macro
m68knommu: define arch_has_single_step() and friends
m68knommu: add uboot commandline argument passing support
m68knommu: Coldfire GPIO corrections
m68knommu: move mcf_remove to .devexit.text
Fixed up (?) conflict in arch/m68k/include/asm/ptrace.h
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (137 commits)
sh: include empty zero page in romImage
sh: Make associative cache writes fatal on all SH-4A parts.
sh: Drop associative writes for SH-4 cache flushes.
sh: Partial revert of copy/clear_user_highpage() optimizations.
sh: Add default uImage rule for se7724, ap325rxa, and migor.
sh: allow runtime pm without suspend/resume callbacks
sh: mach-ecovec24: Remove un-defined settings for VPU
sh: mach-ecovec24: LCDC drive ability become high
sh: fix sh7724 VEU3F resource size
serial: sh-sci: Fix too early port disabling.
sh: pfc: pr_info() -> pr_debug() cleanups.
sh: pfc: Convert from ctrl_xxx() to __raw_xxx() I/O routines.
sh: Improve kfr2r09 serial port setup code
sh: Break out SuperH PFC code
sh: Move KEYSC header file
sh: convert /proc/cpu/aligmnent, /proc/cpu/kernel_alignment to seq_file
sh: Add CPG save/restore code for sh7724 R-standby
sh: Add SDHI power control support to Ecovec
mfd: Add power control platform data to SDHI driver
sh: mach-ecovec24: modify address map
...
Linus Torvalds [Thu, 10 Dec 2009 03:02:46 +0000 (19:02 -0800)]
Merge branch 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (69 commits)
davinci: Initial support for Neuros OSD2 platform.
davinci: remove unused variable in arch/arm/mach-davinci/board-sffsdr.c
davinci: fix section mismatch warning in arch/arm/mach-davinci/board-dm646x-evm.c
DaVinci: DM365: Enable DaVinci RTC support for DM365 EVM
DA8xx/OMAP-L1xx: Add high speed SD/MMC capabilities
davinci: DA8XX/OMAP-L1XX: enable cpuidle and regulator in defconfig
davinci: DA850/OMAP-L138: avoid using separate initcall for initializing regulator
davinci: DA850/OMAP-L138 EVM: register for cpuidle support
davinci: DA8XX/OMAP-L1XX: add support for cpuidle driver register
davinci: add CPU idle driver
davinci: DA8XX/OMAP-L1XX: fix compiler warning
davinci: DA850/OMAP-L138: eliminate static function declaration
davinci: DA850/OMAP-L138 EVM: simplify configuration of emac in MII/RMII mode
davinci: DA850/OMAP-L138 EVM: get rid of DA850_UI_EXP config option
davinci: DA850/OMAP-L138 EVM: implement autodetect of RMII PHY
davinci: DA830/OMAP-L137 EVM: do not configure NAND on UI card when MMC/SD is selected
davinci: DA830/OMAP-L137 EVM: use runtime detection for UI card
davinci: DA830/OMAP-L137 EVM: remove ifdefs inside da830_evm_init()
davinci: DA830/OMAP-L137 EVM: fix warning with default config
davinci: Add NAND support for DA830/OMAP-L137 EVM platform
...
the description in Documentation/filesystems/proc.txt of the
procs_running entry in /proc/stat is confusing (according to that
description, it looks as if procs_running could only be a number
between 0 and the number of CPUs).
Changed it to a more accurate description in the patch attached.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The bkl has been removed from nvram_llseek() and smp_lock.h was removed
because another patch in the same tree zapped the remaining usage of bkl
in the same file. But this patch must have been excluded later, then we
still need the smp_lock.h headers for the bkl use in nvram_open().
This fixes the following build error:
drivers/char/nvram.c: In function ‘nvram_open’:
drivers/char/nvram.c:332: erreur: implicit declaration of function ‘lock_kernel’
drivers/char/nvram.c:339: erreur: implicit declaration of function ‘unlock_kernel’
make[2]: *** [drivers/char/nvram.o] Erreur 1
make[1]: *** [drivers/char] Erreur 2
make: *** [drivers] Erreur 2
Theodore Ts'o [Thu, 10 Dec 2009 02:09:58 +0000 (21:09 -0500)]
ext4: Do not override ext2 or ext3 if built they are built as modules
The CONFIG_EXT4_USE_FOR_EXT23 option must not try to take over the
ext2 or ext3 file systems if the those file system drivers are
configured to be built as mdoules.
Jean Delvare [Wed, 9 Dec 2009 19:36:08 +0000 (20:36 +0100)]
hwmon: (adt7475) Add VID support for the ADT7476
The ADT7476 has 5 dedicated pins for VID input, and the +12V input can
optionally be used as a 6th VID pin. Add support for VID input.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Jordan Crouse <jordan@cosmicpenguin.net> Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Jean Delvare [Wed, 9 Dec 2009 19:36:08 +0000 (20:36 +0100)]
hwmon: (adt7475) Add an entry in MAINTAINERS
As I've just done a lot of changes to the adt7475 driver, I volunteer
to maintain it for the year to come.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Jordan Crouse <jordan@cosmicpenguin.net> Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Jean Delvare [Wed, 9 Dec 2009 19:36:08 +0000 (20:36 +0100)]
hwmon: (adt7475) Add support for the ADT7476
Add support for the Analog Devices ADT7476 chip. This chip is largely
compatible with the ADT7473 and ADT7475, with additional features.
In particular, it has 5 voltage inputs instead of 2, and VID input
pins.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Jordan Crouse <jordan@cosmicpenguin.net> Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Jean Delvare [Wed, 9 Dec 2009 19:36:07 +0000 (20:36 +0100)]
hwmon: (adt7475) Voltage attenuators can be bypassed
It is possible to bypass the voltage attenuators on the +2.5V, Vccp,
+5V and +12V voltage monitoring inputs. This is useful to connect
other voltage channels than the ones the monitoring chip was
originally designed for. When this feature is enabled, we must not
include the scaling factors in our computations.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Jordan Crouse <jordan@cosmicpenguin.net> Cc: "Darrick J. Wong" <djwong@us.ibm.com>
projects / linux-beck.git / log