Magnus Damm [Fri, 29 Mar 2013 08:00:21 +0000 (17:00 +0900)]
ARM: shmobile: APE6EVM LAN9220 support
Add LAN9220 support to the APE6EVM board using C and DT.
At this point the PFC driver lacks DT bindings so to
configure the PFC we use PINCTRL in C board code.
Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Simon Horman [Wed, 3 Apr 2013 01:49:18 +0000 (10:49 +0900)]
Merge tag 'renesas-pinmux2-for-v3.10' into boards-base
Second round of Renesas ARM and SH based SoC pinmux updates for v3.10
Highlights:
* Compilation fixes for sh7269 and for when CONFIG_BUG is not set
* sh-pfc Support for r8a73a4 SoC
* Move GPIOs handling from the PFC device to separate GPIO devices on the r8a7779 SoC
This pull request is based on a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-pinmux-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-soc2-for-v3.10
This merge is made to supply run-time dependencies for the following
patches that will bea added on top:
ARM: shmobile: APE6EVM LAN9220 support
ARM: shmobile: APE6EVM PFC support
Magnus Damm [Tue, 26 Mar 2013 13:50:09 +0000 (22:50 +0900)]
sh-pfc: r8a73a4: GPIO IRQ support
V2 of code to add GPIO -> IRQ mappings to the
PFC table for the r8a73a4 SoC. Requires the IRQs
to be mapped at a fixed location in Linux IRQ
space. The actual IRQs are not handled by the
PFC, instead IRQC is used on r8a73a4.
Signed-off-by: Magnus Damm <damm@opensource.se> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Tue, 26 Mar 2013 13:49:59 +0000 (22:49 +0900)]
sh-pfc: r8a73a4: Support sparse GPIO numbers
The r8a73a4 SoC has sparse GPIO numbers. Declare ranges for pin numbers
in the PFC SoC data. Pin numbers shall be used with the GPIO API from
this point on.
Signed-off-by: Magnus Damm <damm@opensource.se> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Tue, 26 Mar 2013 13:49:49 +0000 (22:49 +0900)]
sh-pfc: Add r8a73a4 pinmux support
Add initial PFC support for the r8a73a4 SoC.
At this point only GPIO interface is supported, move to newer interfaces
planned as incremental changes.
Original authors are Morimoto-san with help from Yoshii-san, thanks to
them for the heavy lifting. Adjusted by Magnus to work together with
updated code in drivers/pinctrl.
Laurent Pinchart [Sun, 10 Mar 2013 16:30:25 +0000 (17:30 +0100)]
sh-pfc: Configure pins as GPIOs at request time when handled externally
When a GPIO is handled by a separate driver the pinmux
gpio_set_direction() handler won't be called. The pin mux type then need
to be configured to GPIO at request time.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Sun, 10 Mar 2013 02:19:44 +0000 (03:19 +0100)]
sh-pfc: Skip gpiochip registration when no GPIO resource is found
Boards/platforms that register dedicated GPIO devices will not supply a
memory resource for GPIOs. Try to locate the GPIO memory resource at
initialization time, and skip registration of the gpiochip if the
resource can't be found.
This is a temporary modification to ease the transition to separate GPIO
drivers. It should be reverted when all boards and platforms will have
been moved.
Laurent Pinchart [Sun, 10 Mar 2013 02:19:44 +0000 (03:19 +0100)]
sh-pfc: Make GPIO support optional
When implemented as a separate IP block, GPIOs should be handled by a
separate driver. To make this possible GPIO support needs to be optional
in the sh-pfc driver.
If no GPIO data registers are supplied in the SoC information structure
skip registration of the gpiochip.
The target is to get rid of function GPIOs completely. To reach this,
make function GPIOs support optional by skipping the function GPIO chip
registration if no function GPIOS are defined in SoC data.
Magnus Damm [Wed, 13 Mar 2013 11:32:13 +0000 (20:32 +0900)]
gpio: Renesas R-Car GPIO driver V3
This patch is V3 of a GPIO driver for the R-Car series of
SoCs from Renesas. This driver is designed to be reusable
between multiple SoCs that share the same basic building block,
but so far it has only been used on R-Car H1 (r8a7779).
Each driver instance handles 32 GPIOs with individually
maskable IRQs. The driver operates on a single I/O memory
range and the 32 GPIOs are hooked up a single interrupt.
In the case of R-Car H1 either external IRQ pins or GPIOs
with interrupts can be used for on-board interupts. For
external IRQs 4 pins are supported, and in the case of GPIO
there are 202 GPIOS as 202 interrupts hooked up via 6 driver
instances and to the GIC and the Cortex-A9 Quad.
At this point this driver is interfacing as a regular
platform device driver. In the future DT support will be
submitted as an incremental feature patch.
Signed-off-by: Magnus Damm <damm@opensource.se> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Refactor the GPIO macro magic to use GPIO numbers directly instead of
the GPIO_GP_x_y enum entries. This will allow removing the GPIO enum
entries from the mach/r8a7779.h header.
Laurent Pinchart [Tue, 26 Mar 2013 00:44:52 +0000 (01:44 +0100)]
sh-pfc: Fix compiler warning when BUG()
The sh_pfc_phys_to_virt() function ends with a BUG() statement without a
return. When CONFIG_BUG isn't set the function will thus have no return
value. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Simon Horman [Tue, 2 Apr 2013 02:08:34 +0000 (11:08 +0900)]
Merge branch 'soc' into pinmux-base
Conflicts:
drivers/pinctrl/sh-pfc/pfc-r8a7740.c
This merge is to provide r8a73a4 SoC files, which are added in the
soc branch and depended on by r8a73a4 pfc-changes which are to
be added to the pinmux branch.
Magnus Damm [Wed, 27 Mar 2013 15:49:54 +0000 (00:49 +0900)]
ARM: shmobile: r8a7790 IRQC support
Add IRQC interrupt controller support to r8a7790 by
hooking up a single IRQC instances to handle 4 external
IRQ signals. The IRQC controller is tied to SPIs of
the GIC. On r8a7790 the external IRQ pins routing is
handled by the PFC which is excluded from this patch.
Both platform devices and DT devices are added in this
patch. The platform device versions are used to provide
a static interrupt map configuration for board code
written in C.
Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Wed, 27 Mar 2013 15:49:44 +0000 (00:49 +0900)]
ARM: shmobile: r8a7790 SCIF support
Add SCIF serial port support to the r8a7790 SoC by
adding platform devices for SCIFA0 -> SCIFA2 as well
as SCIFB0 -> SCIFB2 and SCIF0 -> SCIF1 together with
clock bindings. DT device description is excluded at
this point since such bindings are still under
development.
Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Wed, 27 Mar 2013 15:49:34 +0000 (00:49 +0900)]
ARM: shmobile: Initial r8a7790 SoC support
Add initial support for the r8a7790 SoC including:
- Single Cortex-A15 CPU Core
- GIC
- Architecture timer
No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: shmobile: r8a7779: remove DIV4 clocks and use fixed ratio clock
R-Car H1 has many clocks, and it is possible to read/use clock ratio
of these clocks from FRQMRx as DIV4 clocks.
But, these ratio are fixed value and these are decided
by MD pin status.
This means that we can use fixed ratio clock via MD pin status,
instead of DIV4 clocks.
This patch reads MD pin status, and sets PLLA clock (= root clock),
and used fixed ratio clock for other clocks.
It was tesed on marzen board.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Acked-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: shmobile: add struct clk_ratio and fixed ratio clock macro
Renesas chip has many clocks inside,
and some of them are using fixed ratio via parent clock.
Current shmobile clock code is using own divX_recalc function
and divX_clk_ops.
This patch can reduce these code
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Acked-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Bastian Hecht [Wed, 27 Mar 2013 13:54:04 +0000 (14:54 +0100)]
ARM: shmobile: r8a7740: Migrate from INTC to GIC
With the added capabilty of the intc_irqpin driver to handle shared
external IRQs, all prerequisites are fulfilled and we are ready to
migrate completely to GIC. This includes the following steps:
- Kconfig: select ARM_GIC and RENESAS_INTC_IRQPIN
- intc-r8a7740: Throw out all legacy INTC code and init the GIC. We need
to mask out all shared IRQs as it is needed by the
shared intc_irqpin driver.
- setup-r8a7740: Add 4 irqpin devices to handle external IRQs and update
all IRQ numbers to point to the GIC SPI.
- board-armadillo: Update all IRQ numbers to point to the GIC SPI.
- pfc-r8a7740: Update all IRQ numbers of the GPIOs to point to the GIC
SPI.
Magnus Damm [Mon, 18 Mar 2013 13:58:18 +0000 (22:58 +0900)]
ARM: shmobile: Disallow PINCTRL without GPIOLIB
Modify mach-shmobile to only select PINCTRL in case of
ARCH_WANT_OPTIONAL_GPIOLIB is set.
This fixes a build error triggered when adding a new SoC
lacking GPIO software support (ARCH_WANT_OPTIONAL_GPIOLIB=n):
CC drivers/tty/vt/keyboard.o
In file included from drivers/pinctrl/core.c:30:0:
include/asm-generic/gpio.h: In function 'gpio_get_value_cansleep':
include/asm-generic/gpio.h:270:2: error: implicit declaration of function '__gpio_get_value'
include/asm-generic/gpio.h: In function 'gpio_set_value_cansleep':
include/asm-generic/gpio.h:276:2: error: implicit declaration of function '__gpio_set_value'
drivers/pinctrl/core.c: In function 'pinctrl_ready_for_gpio_range':
drivers/pinctrl/core.c:297:9: error: implicit declaration of function 'gpio_to_chip'
drivers/pinctrl/core.c:297:27: warning: initialization makes pointer from integer without a cast
drivers/pinctrl/core.c:304:45: error: dereferencing pointer to incomplete type
drivers/pinctrl/core.c:305:26: error: dereferencing pointer to incomplete type
drivers/pinctrl/core.c:305:39: error: dereferencing pointer to incomplete type
make[2]: *** [drivers/pinctrl/core.o] Error 1
make[1]: *** [drivers/pinctrl] Error 2
make[1]: *** Waiting for unfinished jobs....
LD drivers/sh/built-in.o
Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DT nodes for the 4 irqpin interrupt controllers on sh73a0. We add them
to sh73a0.dtsi, which is also used by configurations, doing all their
device instantiation from board the .c code. We rely on the fact, that
such configurations don't instantiate devices from the device-tree.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SCIF serial port support to the r8a7778 SoC by
adding platform devices together with clock bindings.
DT device description is excluded at this point since
such bindings are still under development.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Acked-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the R8A7778 R-Car M1A SoC.
No static virtual mappings are used, all the components
make use of ioremap().
DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
It is based on v1.0 datasheet
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Acked-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: shmobile: sh73a0: wait for completion when kicking the clock
To reconfigure clocks, controlled by FRQCRA and FRQCRB, a kick bit has to
be set and to make sure the setting has taken effect, it has to be read
back repeatedly until it is cleared by the hardware. This patch adds the
waiting part, that was missing until now.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Magnus Damm <damm@opensource.se Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Tue, 26 Mar 2013 01:34:42 +0000 (10:34 +0900)]
ARM: shmobile: r8a73a4 IRQC support V2
Add IRQC interrupt controller support to r8a73a4 by
hooking up two IRQC instances to handle 58 external
IRQ signals. There IRQC controllers are tied to SPIs
of the GIC. On r8a73a4 exact IRQ pin routing is handled
by the PFC which is excluded from this patch.
Both platform devices and DT devices are added in this
patch. The platform device versions are used to provide
a static interrupt map configuration for board code
written in C.
Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Tue, 26 Mar 2013 01:34:33 +0000 (10:34 +0900)]
ARM: shmobile: r8a73a4 SCIF support V3
V3 of SCIF serial port support for the r8a73a4 SoC.
This is done by adding platform devices for SCIFA0
-> SCIFA1 as well as SCIFB0 -> SCIFB3 together with
clock bindings. DT device description is excluded at
this point since such bindings are still under
development.
Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Tue, 26 Mar 2013 01:34:24 +0000 (10:34 +0900)]
ARM: shmobile: Initial r8a73a4 SoC support V3
V3 of initial support for the r8a73a4 SoC including:
- Single Cortex-A15 CPU Core
- GIC
- Architecture timer
No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Simon Horman [Tue, 2 Apr 2013 01:55:57 +0000 (10:55 +0900)]
Merge tag 'renesas-intc-external-irq2-for-v3.10' into soc-base
Update for Renesas INTC External IRQ pin driver for v3.10
This adds support for shared interrupt lines to the
Renesas INTC External IRQ pin driver which has already
been queued up for v3.10 (tag renesas-intc-external-irq-for-v3.10).
The patch "irqchip: intc-irqpin: Add support for shared interrupt lines"
in renesas-intc-external-irq2-for-v3.10 is a dependency for
"ARM: shmobile: r8a7740: Migrate from INTC to GIC". That dependency is
the reason for this merge.
Bastian Hecht [Wed, 27 Mar 2013 13:54:03 +0000 (14:54 +0100)]
irqchip: intc-irqpin: Add support for shared interrupt lines
On some hardware we don't have a 1-1 mapping from the external
interrupts coming from INTC to the GIC SPI pins. We can however
share lines to demux incoming IRQs on these SoCs.
This patch enables the intc_irqpin driver to detect requests for shared
interrupt lines and demuxes them properly by querying the INTC INTREQx0A
registers.
If you need multiple shared intc_irqpin device instances, be sure to mask
out all interrupts on the INTC that share the one line before you start
to register them. Else you run into IRQ floods that would be caused by
interrupts for which no handler has been set up yet when the first
intc_irqpin device is registered.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com> Acked-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This appears to be incompatible with
"ARM: shmobile: sh7372: Remove SDHI and MMCIF function GPIOs"
Reverting this change resolves the following build failure:
arch/arm/mach-shmobile/board-mackerel.c: In function ‘mackerel_init’:
arch/arm/mach-shmobile/board-mackerel.c:1468: error: ‘GPIO_FN_SDHICMD1’ undeclared (first use in this function)
arch/arm/mach-shmobile/board-mackerel.c:1468: error: (Each undeclared identifier is reported only once
arch/arm/mach-shmobile/board-mackerel.c:1468: error: for each function it appears in.)
arch/arm/mach-shmobile/board-mackerel.c:1469: error: ‘GPIO_FN_SDHICLK1’ undeclared (first use in this function)
arch/arm/mach-shmobile/board-mackerel.c:1470: error: ‘GPIO_FN_SDHID1_3’ undeclared (first use in this function)
arch/arm/mach-shmobile/board-mackerel.c:1471: error: ‘GPIO_FN_SDHID1_2’ undeclared (first use in this function)
arch/arm/mach-shmobile/board-mackerel.c:1472: error: ‘GPIO_FN_SDHID1_1’ undeclared (first use in this function)
arch/arm/mach-shmobile/board-mackerel.c:1473: error: ‘GPIO_FN_SDHID1_0’ undeclared (first use in this function)
arch/arm/mach-shmobile/board-mackerel.c:1489: error: ‘GPIO_FN_SDHICMD2’ undeclared (first use in this function)
arch/arm/mach-shmobile/board-mackerel.c:1490: error: ‘GPIO_FN_SDHICLK2’ undeclared (first use in this function)
arch/arm/mach-shmobile/board-mackerel.c:1491: error: ‘GPIO_FN_SDHID2_3’ undeclared (first use in this function)
arch/arm/mach-shmobile/board-mackerel.c:1492: error: ‘GPIO_FN_SDHID2_2’ undeclared (first use in this function)
arch/arm/mach-shmobile/board-mackerel.c:1493: error: ‘GPIO_FN_SDHID2_1’ undeclared (first use in this function)
arch/arm/mach-shmobile/board-mackerel.c:1494: error: ‘GPIO_FN_SDHID2_0’ undeclared (first use in this function)
ARM: shmobile: kzm9g-reference: fix device-tree bindings and device names
Fix several device-tree bindings, that haven't been updated for newest
versions of respective drivers, and device names and pin numbers, left over
from non-DT and old pinctrl versions.
ARM: shmobile: kzm9g: add fixed voltage regulators for SDHI0 and SDHI2
Both SDHI0 and SDHI2 power supplies on kzm9g can be switched on and off. In
the current version this is not used and the regulators are hard-wired to
"on." This patch switches SDHI0 and SDHI2 to proper fixed-voltage
regulators, using GPIOs to enable and disable them. Both ports shall
now be specifying the MMC_CAP_POWER_OFF_CARD MMC capability. Only SDHI0
has been tested with an SDIO card, since SDHI2 is a microSD slot.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: shmobile: armadillo800eva: add a fixed voltage regulator for SDHI1
The SDHI1 power supply on armadillo800eva can be switched on and off. In
the current version this is not used and the regulator is hard-wired to
"on." This patch switches SDHI1 to a proper fixed-voltage regulator,
using a GPIO to enable and disable it. Both SDHI0 and SDHI1 ports shall
now be specifying the MMC_CAP_POWER_OFF_CARD MMC capability. Both
interfaces tested with an SDIO card.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: shmobile: sh73a0: move SDHI and MMCIF DT nodes to sh73a0.dtsi
To avoid having to repeat common DT node properties in all .dts files
move them to SoC's .dtsi file, setting their status to "disabled."
Individual boards will pick up devices, that they want to use and
change their DT node status to enabled.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: shmobile: kzm9g: SDHI0 and SDHI1 use a 3.3V power supply
kzm9g supplies 3.3V to its SDHI0 and SDHI2 interfaces. Specifying 2.8V
prevents some (e.g. certain SDIO) cards from working. This patch fixes the
voltage and removes redundant OCR masks from platform data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: shmobile: marzen: Use gic_iid macro for ICCIAR / interrupt ID
ARM: shmobile: add gic_iid macro for ICCIAR / interrupt ID
enabled to use gic_iid macro.
This patch exchange current GIC interrupt setting
from gic_spi() to gic_iid()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[ horms+renesas@verge.net.au: Split irq.h portion into a separate patch ] Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Simon Horman [Fri, 15 Feb 2013 12:38:20 +0000 (21:38 +0900)]
ARM: shmobile: kzm9g: Trim reference DT_MACHINE_START
Remove .init_late and .restart from DT_MACHINE_START
for kzm9g reference as these are not necessary to
bring the board up which is the main aim of kzm9g reference.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reference kernel configurations for armadillo800eva and kzm9g boards do not
have to depend on their respective "legacy" configurations, doing device
instantiation in .c, they can be configured and built independently.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Linus Walleij <linus.walleij@linaro.org>
[horms+renesas@verge.net.au: created separate patch for kzm9g portion] Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: shmobile: SDHI and MMCIF interfaces to kzm9g-reference
Add SDHI0 and SDHI2 interfaces to kzm9g-reference. With no pinctrl DT
support we cannot use GPIO card-detection and regulator switching.
Also update the MMCIF DT node to use all 8 data lines and avoid
redundant information in DT.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
[ horms+renesas@verge.net.au: Updated for pinmux changes by Laurent Pinchart ] Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: shmobile: parse DT and configure pinmux early on kzm9g-reference
GPIOs can be provided by the pinctrl subsystem, which can be initialised
by DT. Therefore DT has to be parsed before requesting GPIOs. Also non-DT
pinmux has to be configured early.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Simon Horman [Wed, 21 Nov 2012 15:34:25 +0000 (00:34 +0900)]
ARM: shmobile: kzm9g: Reference DT implementation
Provide alternate board code for the kzm9g to demonstrate
how DT may be used given the current state of driver
device tree support. This is intended to act as a reference
for mach-shmobile developers.
Some notes:
* Brings up the GIC interrupt handler using device tree
* Brings up the following device using device tree:
- MMCIF (MMC)
* Does not bring up the INTC interrupt controller at all,
thus external devices may not be used. In particular,
the SMSC ethernet device may not be used and thus
NFS root may not be used.
* Uses existing C code and not device tree to initialise the following,
which are needed for a working board:
- SCIF (Serial)
- CMT (Clock)
- PFC (GPIO)
To use this alternate board code instead of the normal board code,
CONFIG_MACH_KZM9G_REFERENCE should be selected in the kernel config.
And the sh73a0-kzm9g-reference.dtb flattened device tree blob should be used.
Includes fix by Thierry Reding to no longer use gic_handle_irq()
Includes fixes by Guennadi Liakhovetski for recent pinmux changes.
Provide alternate board code for the marzen to demonstrate
how DT may be used given the current state of driver
device tree support. This is intended to act as a reference
for mach-shmobile developers.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Arnd Bergmann [Thu, 14 Feb 2013 22:26:54 +0000 (23:26 +0100)]
ARM: shmobile: mark mackerel sh_mmcif_device __maybe_unused
Patch eac036ef9e "ARM: shmobile: streamline mackerel SD and MMC devices"
made the use of the sh_mmcif_device variable for mackarel optional,
but the definition is always provided, causing a build warning.
arch/arm/mach-shmobile/board-mackerel.c:1120:31: warning: 'sh_mmcif_device'
defined but not used [-Wunused-variable]
Marking the variable as __maybe_unused will do the right thing here.
ARM: shmobile: streamline mackerel SD and MMC devices
This patch fixes the following issues with SD and MMC interfaces on mackerel:
1. replace custom card-detection functions with standard GPIO CD API
2. resources don't have to be numbered
3. add SDHI interrupt names
4. remove OCR masks, where regulators are used
5. only specify SDHI CD interrupts on interfaces where a CD pin is present -
SDHI0
6. don't instantiate an MMCIF device and initialise MMCIF pins if SDHI1 is
selected
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: shmobile: switch SDHI0 to GPIO regulator on armadillo800eva
When regulators are used with MMC devices, explicitly provided OCR masks
are ignored, they can be removed from platform data. Also switch SDHI0
from fixed regulator with hard-wired GPIO levels to a proper GPIO regulator
instance to enable dynamic voltage switching.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: shmobile: use GPIO SD-card detection on armadillo800eva
Switch SDHI0 and SDHI1 SD-card interfaces on armadillo800eva to using GPIO
card detection, which provides maximum power saving and automatically
selects IRQ or polling mode, depending on the CD GPIO capability.
Magnus Damm [Wed, 27 Feb 2013 08:15:01 +0000 (17:15 +0900)]
irqchip: Renesas IRQC driver
This patch adds a driver for external IRQ pins connected
to the IRQC hardware block on recent SoCs from Renesas.
The IRQC hardware block is used together with more
recent ARM based SoCs using the GIC. As usual the GIC
requires external IRQ trigger setup somewhere else
which in this particular case happens to be IRQC.
This driver implements the glue code needed to configure
IRQ trigger and also handle mask/unmask and demux of
external IRQ pins hooked up from the IRQC to the GIC.
Tested on r8a73a4 but is designed to work with a wide
range of SoCs. The driver requires one GIC SPI per
external IRQ pin to operate. Each driver instance
will handle up to 32 external IRQ pins.
The SoCs using this driver are currently mainly used
together with regular platform devices so this driver
allows configuration via platform data to support things
like static interrupt base address. DT support will
be added incrementally in the not so distant future.
Signed-off-by: Magnus Damm <damm@opensource.se> Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Tue, 26 Feb 2013 03:01:18 +0000 (12:01 +0900)]
ARM: shmobile: INTC External IRQ pin driver on r8a7779
Update the r8a7779 IRQ code to make use of the
INTC External IRQ pin driver for external
interrupt pins IRQ0 -> IRQ3.
The r8a7779 SoC can like older SH SoCs configure
to use the IRQ0 -> IRQ3 signals as individual
interrupts or a combined IRL mode.
Without this patch the r8a7779 SoC code does
not fully support external IRQ pins in individual
IRQ mode. The r8a7779 PFC code does not yet have
gpio_to_irq() support so no need to update such
code.
At this point the DT reference implementations
are not covered. In the future such code shall
tie in the INTC External IRQ pin driver via
DT, so this kind of verbose code is not needed
for the long term DT case.
Signed-off-by: Magnus Damm <damm@opensource.se> Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Tue, 26 Feb 2013 03:01:09 +0000 (12:01 +0900)]
ARM: shmobile: INTC External IRQ pin driver on sh73a0
Adjust the sh73a0 IRQ code to make use of the
INTC External IRQ pin driver for external
interrupt pins IRQ0 -> IRQ31.
This removes quite a bit of special-case code
in intc-sh73a0.c but the number of lines get
replaced with platform device information in
setup-sh73a0.c. The PFC code is also adjusted
to make gpio_to_irq() return the correct
interrupt number.
At this point the DT reference implementations
are not covered. In the future such code shall
tie in the INTC External IRQ pin driver via
DT, so this kind of verbose code is not needed
for the long term DT case.
Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>