Gabor Juhos [Tue, 4 Jun 2013 11:40:38 +0000 (13:40 +0200)]
rt2x00: rt2x00queue: add priv_size field to struct data_queue
Add a new field into struct data_queue and store
the size of the per-queue_entry private data in
that. Additionally, use the new field in the
rt2x00queue_alloc_entries function to compute
the size of the queue entries for a given queue.
The patch does not change the current behaviour
but makes it possible to remove the queue_desc
parameter of the rt2x00queue_alloc_entries function.
That will be done by a subsequent patch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit, "ath9k_hw: improve ANI processing and rx desensitizing parameters"
modified the immunity level tables for both CCK and OFDM. Fix them
so that the tables are in sync with the internal driver/codebase.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k_hw: improve ANI processing and rx desensitizing parameters"
changed various ANI operational parameters to address a specific
card/environment. This is not really applicable for other cards
in general usage.
As per internal documentation, lowering the immunity level can be
done only after 5 periods have passed and the CCK/OFDM errors are
below the low watermak threshold - which have been fixed at 300 and
400 respectively by the sytems team.
Raising the immunity level can be done when CCK/OFDM errors exceed
600 and 1000 (per second).
Set these values once during attach.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k_hw: improve ANI processing and rx desensitizing parameters"
changed the OFDM weak signal detection logic to disable it
for AP mode, which is not allowed. Fix this and enable it always
for AP mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kees Cook [Fri, 10 May 2013 21:48:21 +0000 (14:48 -0700)]
b43: stop format string leaking into error msgs
The module parameter "fwpostfix" is userspace controllable, unfiltered,
and is used to define the firmware filename. b43_do_request_fw() populates
ctx->errors[] on error, containing the firmware filename. b43err()
parses its arguments as a format string. For systems with b43 hardware,
this could lead to a uid-0 to ring-0 escalation.
CVE-2013-2852
Signed-off-by: Kees Cook <keescook@chromium.org> Cc: stable@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k rate control algorithm has various architectural
issues that make it a poor fit in scenarios like congested
environments etc.
An example: https://bugzilla.redhat.com/show_bug.cgi?id=927191
Change the default to minstrel which is more robust in such cases.
The ath9k RC code is left in the driver for now, maybe it can
be removed altogether later on.
Cc: stable@vger.kernel.org Cc: Jouni Malinen <jouni@qca.qualcomm.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change reduces rx sensitivity with no apparent extra benefit.
It looks like it was meant for testing in a specific scenario,
but it was never properly validated.
Cc: rmanohar@qca.qualcomm.com Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Almost all the DMA issues which have plagued ath9k (in station mode)
for years are related to PS. Disabling PS usually "fixes" the user's
connection stablility. Reports of DMA problems are still trickling in
and are sitting in the kernel bugzilla. Until the PS code in ath9k is
given a thorough review, disbale it by default. The slight increase
in chip power consumption is a small price to pay for improved link
stability.
Cc: stable@vger.kernel.org Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com> Cc: Stanislaw Gruszka <sgruszka@redhat.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: netdev@vger.kernel.org Cc: linux-wireless@vger.kernel.org Cc: Jingoo Han <jg1.han@samsung.com> Acked-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Tue, 7 May 2013 12:41:09 +0000 (15:41 +0300)]
wl12xx/wl18xx: scan all 5ghz channels
Due to a typo, the current code copies only sizeof(cmd->channels_2)
bytes, which is smaller than the correct sizeof(cmd->channels_5)
size, resulting in a partial scan (some channels are skipped).
Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 10 May 2013 07:19:38 +0000 (10:19 +0300)]
wl12xx: fix minimum required firmware version for wl127x multirole
There was a typo in commit 8675f9 (wlcore/wl12xx/wl18xx: verify
multi-role and single-role fw versions), which was causing the
multirole firmware for wl127x (WiLink6) to be rejected. The actual
minimum version needed for wl127x multirole is 6.5.7.0.42.
Reported-by: Levi Pearson <levipearson@gmail.com> Reported-by: Michael Scott <hashcode0f@gmail.com> Cc: stable@kernel.org # 3.9+ Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Thu, 30 May 2013 23:05:55 +0000 (18:05 -0500)]
rtlwifi: rtl8192cu: Fix problem in connecting to WEP or WPA(1) networks
Driver rtl8192cu can connect to WPA2 networks, but fails for any other
encryption method. The cause is a failure to set the rate control data
blocks. These changes fix https://bugzilla.redhat.com/show_bug.cgi?id=952793
and https://bugzilla.redhat.com/show_bug.cgi?id=761525.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The panic is caused by the mwifiex_info_read() routine assuming that
there can only be four modes (0-3) which is an invalid assumption.
For example, when testing P2P, the mode is '8' (P2P_CLIENT) so the
code accesses data beyond the bounds of the bss_modes[] array which
causes the panic. Fix this by updating bss_modes[] to support the
current list of modes and adding a check to prevent the out-of-bounds
access from occuring in the future when more modes are added.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Acked-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johan Hedberg [Wed, 29 May 2013 06:51:29 +0000 (09:51 +0300)]
Bluetooth: Fix mgmt handling of power on failures
If hci_dev_open fails we need to ensure that the corresponding
mgmt_set_powered command gets an appropriate response. This patch fixes
the missing response by adding a new mgmt_set_powered_failed function
that's used to indicate a power on failure to mgmt. Since a situation
with the device being rfkilled may require special handling in user
space the patch uses a new dedicated mgmt status code for this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Cc: stable@vger.kernel.org Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johan Hedberg [Tue, 28 May 2013 10:46:30 +0000 (13:46 +0300)]
Bluetooth: Fix missing length checks for L2CAP signalling PDUs
There has been code in place to check that the L2CAP length header
matches the amount of data received, but many PDU handlers have not been
checking that the data received actually matches that expected by the
specific PDU. This patch adds passing the length header to the specific
handler functions and ensures that those functions fail cleanly in the
case of an incorrect amount of data.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johan Hedberg [Wed, 24 Apr 2013 10:05:32 +0000 (13:05 +0300)]
Bluetooth: Fix checks for LE support on LE-only controllers
LE-only controllers do not support extended features so any kind of host
feature bit checks do not make sense for them. This patch fixes code
used for both single-mode (LE-only) and dual-mode (BR/EDR/LE) to use the
HCI_LE_ENABLED flag instead of the "Host LE supported" feature bit for
LE support tests.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Solomon Peachy [Tue, 11 Jun 2013 13:49:39 +0000 (09:49 -0400)]
cw1200: Eliminate the ETF debug/engineering code.
This is only really useful for people who are bringing up new hardware
designs and have access to the proprietary vendor tools that interface
with this mode.
It'll live out of tree until it's rewritten to use a less kludgy interface.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support for rt2800 device is broken since my
'rt2x00: rt2x00dev: use rt2x00dev->tx->limit'
patch. The changelog of that commit says that the
TX data queue is initialized already when the
rt2x00lib_probe_hw() function is called.
However as Jakub noticed it, this statement is not
correct. The queue->limit field is initialized in
the rt2x00queue_alloc_entries routine and that is
not yet called when rt2x00lib_probe_hw() runs.
Because the value of tx->limit contains zero, the
driver tries to allocate a kernel fifo with zero
size and kfifo_alloc rejects that with -EINVAL.
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 3071, rev 021c detected
ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 0008 detected
ieee80211 phy1: rt2x00lib_probe_dev: Error - Failed to initialize hw
rt2800pci: probe of 0000:01:00.0 failed with error -22
Move the data_queue field initialization from
the rt2x00queue_alloc_entries routine into the
rt2x00queue_init function. The initialization
code is not strictly related to the allocation,
and the change ensures that the queue_data fields
can be used in the probe routines.
The patch also introduces a helper function in
order to be able to get the correct data_queue_desc
structure for a given queue. This helper is only
needed temporarily and it will be removed later.
Reported-by: Jakub Kicinski <moorray@wp.pl> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yunlian Jiang [Fri, 31 May 2013 21:45:21 +0000 (14:45 -0700)]
rtlwifi: initialize local array and set value.
GCC 4.8 is spitting out uninitialized-variable warnings against
"drivers/net/wireless/rtlwifi/rtl8192de/dm.c".
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:941:31:
error: 'ofdm_index_old[1]' may be used uninitialized in this
function [-Werror=maybe-uninitialized]
rtlpriv->dm.ofdm_index[i] = ofdm_index_old[i];
This patch adds initialization to the variable and properly sets its value.
Signed-off-by: Yunlian Jiang <yunlian@google.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Solomon Peachy [Wed, 5 Jun 2013 03:37:05 +0000 (23:37 -0400)]
cw1200: Sanity-check arguments in copy_from_user()
The optional debugfs interface to the vendor's engineering tools wasn't
bounds checking at all, which made it trivial to perform a buffer
overflow if this interface was compiled in and then explicitly enabled
at runtime.
This patch checks both the length supplied as part of the data to ensure
it is sane, and also the amount of data compared to the remaining buffer
space. If either is too large, fail immediately.
(This bug was spotted by Dan Carpenter <dan.carpenter@oracle.com>)
Signed-off-by: Solomon Peachy <pizza@shaftnet.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
In multicast, there is no retries nor RTS since there is no
specific recipient that can ACK or send CTS. This means
that we must not use the rate scale table for multicast
frames.
This true for any frame that doesn't have a valid
ieee80211_sta pointer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Alexander Bondar [Mon, 27 May 2013 10:49:03 +0000 (13:49 +0300)]
iwlwifi: mvm: enable PM always in unassociated mode
In unassociated BSS STA mode FW verifies both power save and power
management flags to decide on switching power off. The driver currently
sets power management flag according to mac80211 decision. As result, in
unassociated mode power management flag is down and power consumption is
high. Change power management enablement. When unassociated in BPS and
LP power save modes enable power management regardless of mac80211
decision. Rely on mac80211 decision if associated. Add power management
state update during associated/disassociated modes transitions.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Alexander Bondar [Wed, 29 May 2013 07:19:50 +0000 (10:19 +0300)]
iwlwifi: mvm: Change location of vif_count verification for PM
Currently vif_count verification for power management enablement appear
in different places. Move these verifications to one place in
iwl_mvm_update_power_mode().
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwlwifi: mvm: correctly configure MCAST in AP mode
The AP mode needs to use the MCAST fifo for the MCAST
frames sent after the DTIM. This fifo needs to be
configured with the same parameters as the VOICE FIFO.
A separate SCD queue is mapped to this fifo - the cab_queue
(cab stands for Content After Beacon). This queue isn't
connected to any station, but rather to the MAC context.
This queue should (and is already) be set as the MCAST
queue - this is part of the of MAC context command.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Reviewed-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ilan Peer [Thu, 30 May 2013 04:31:01 +0000 (07:31 +0300)]
iwlwifi: mvm: Fix quota command settings
According to the FW implementation, the quota command should
have a valid entry for each active binding (where 'active' in
this context means that the binding is known to the FW). In case
the binding should not get any quota, the 'quota' should be set
to zero.
Not setting an 0 quota for an active binding when all the MACs
in the binding are idle, i.e., not associated in case of managed
interface, will result in preventing the FW scheduler from entering
IDLE state and the FW from transitioning to low PS.
Signed-off-by: Ilan Peer <ilan.peer@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Eran Harary [Sun, 2 Jun 2013 09:40:34 +0000 (12:40 +0300)]
iwlwifi: don't return -ERFKILL if SEND_IF_RFKILL is set
When CMD_SEND_IN_RFKILL is set, it is perfectly legitimate
to send a host command while RFKILL is asserted. In this
case, the host command sending functions should return 0
even if RFKILL is asserted.
Signed-off-by: Eran Harary <eran.harary@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John Greene [Mon, 3 Jun 2013 13:47:39 +0000 (09:47 -0400)]
brcmsmac: Reduce log spam in heavy tx, make err print in debug
Move message to debug mode to reduce log spam under heavy tx (iperf) load.
This message prints in ht debug mode only:
brcms_c_ampdu_dotxstatus_complete: Pkt tx suppressed, illegal channel
possibly 153
Signed-off-by: John Greene <jogreene@redhat.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANI state can be maintained globally instead of per-channel.
This reduces memory usage and since default values are used
during a scan run, per-channel state is not required.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only card with which WoW has been tested and verified is
AR9462. Do not enable it for all cards since WoW is really quirky
and needs to be tested properly with each chip.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Solomon Peachy [Sun, 2 Jun 2013 15:35:31 +0000 (11:35 -0400)]
cw1200: Rework SDIO platform support to prevent build problems.
Based on discussions with And Bergmann, this patch changes the SDIO
platform code to default to supporting the Sagrad devices, allowing for
it to be overridden in board setup code. This renders the cw1200_sagrad
module suplerflous, so it is now removed.
It also moves the documentation that was in the cw1200_sagrad source to
the platform header.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Solomon Peachy [Sun, 2 Jun 2013 13:53:03 +0000 (09:53 -0400)]
cw1200: Replace use of 'struct resource' with 'int' for GPIO fields.
The only advantage of 'struct resource' is that it lets us assign names
as part of the platform data. Unfortunately since we are using platform
data, we are already limited to a single instance of each driver,
rendering this moot.
So, replace the struct resources with ints, resulting in cleaner code.
This was based on a suggestion from Arnd Bergmann.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Solomon Peachy [Sat, 1 Jun 2013 12:08:42 +0000 (08:08 -0400)]
cw1200: Rename 'sbus' to 'hwbus'
This avoids problems when building on SPARC targets due to the driver
calling the bus abstraction layer 'sbus'. Not that any SBUS-sporting
SPARC targets are likely to have an SDIO controller, but this is the
correct thing to do.
See http://kisskb.ellerman.id.au/kisskb/buildresult/8846508/
Signed-off-by: Solomon Peachy <pizza@shaftnet.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 3 Jun 2013 11:51:59 +0000 (13:51 +0200)]
mac80211: fix sdata locking around __ieee80211_request_smps
My cfg80211/mac80211 locking unification broke the sdata
locking in ieee80211_set_power_mgmt, it needs to acquire
the lock for __ieee80211_request_smps(). Add the locking.
Reported-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This wasn't intended to be included here, my mistake. I
accidentally merged a mac80211 fixes tree here that had
this change, when it wasn't even intended to be there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This wasn't intended to be included here, my mistake. I
accidentally merged a mac80211 fixes tree here that had
this change, when it wasn't even intended to be there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 14 May 2013 11:53:45 +0000 (13:53 +0200)]
iwlwifi: mvm: implement D3 testing
For testing the D3 (WoWLAN) firmware, it is useful to be able
to run the firmware with instrumentation while the host isn't
sleeping and can poke at the firmware debug logging etc.
Implement this by a debugfs file. When the file is opened the
D3 firmware is loaded and all regular commands are blocked.
While the file is being read, poll the firmware's PME status
flag and report EOF once it changes to non-zero. When it is
closed, do (most of) the resume processing. This lets a user
just "cat" the file. Pressing Ctrl-C to kill the cat process
will resume the firwmare as though the platform resumed for
non-wireless reason and when the firmware wants to wake up
reading from the file automatically completes.
Unlike in real suspend, only disable interrupts and don't
reset the TX/RX hardware while in the test mode. This is a
workaround for some interrupt problems that happen only when
the PCIe link isn't fully reset (presumably by changing the
PCI config space registers which the core PCI code does.)
Note that while regular operations are blocked from sending
commands to the firmware, they could still be made and cause
strange mac80211 issues. Therefore, while using this testing
feature you need to be careful to not try to disconnect, roam
or similar, and will see warnings for such attempts.
Als note that this requires an upcoming firmware change to
tell the driver the location of the PME status flag in SRAM.
D3 test will fail if the firmware doesn't report the pointer.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Tue, 28 May 2013 16:04:44 +0000 (18:04 +0200)]
ath9k_hw: fix PA predistortion miscalibration
If any bins from the training data are skipped (i != max_index), the
calculated compensation curve gets distorted, and the signal will be
wildly overamplified. This may be the cause of the reported hardware
damage that was caused by PA predistortion (because of which PAPRD was
disabled by default).
When calculating the x_est, Y, theta values, the use of max_index and i
was reversed. i points to the bin index whereas max_index refers to the
index of the calculated arrays.
Note that PA predistortion is still disabled, it will be re-enabled
after it has been properly validated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 28 May 2013 15:24:15 +0000 (17:24 +0200)]
mac80211: always send multicast on CAB queue
If the driver advertised support for a CAB queue, then we
should put all multicast frames there, otherwise sending
them can be racy with clients going to sleep while we TX
a frame. To avoid this, always TX multicast frames on the
multicast queue.
It seems like even drivers not using the queue framework
might want to do this which would mean also moving the
IEEE80211_TX_CTL_SEND_AFTER_DTIM flag assignment, but it
also seems that drivers behave differently here so that
just moving it wouldn't be a good idea. It'd be better to
modify those drivers to use the queue framework.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Tue, 28 May 2013 11:01:53 +0000 (13:01 +0200)]
mac80211: support active monitor interfaces
Support them only if the driver advertises support for them via
IEEE80211_HW_SUPPORTS_ACTIVE_MONITOR. Unlike normal monitor interfaces,
they are added to the driver, along with their MAC address.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Tue, 28 May 2013 11:01:52 +0000 (13:01 +0200)]
cfg80211: support an active monitor interface flag
An active monitor interface is one that is used for communication (via
injection). It is expected to ACK incoming unicast packets. This is
useful for running various 802.11 testing utilities that associate to an
AP via injection and manage the state in user space.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Hila Gonen [Wed, 13 Mar 2013 16:00:03 +0000 (18:00 +0200)]
iwlwifi: mvm: Add support for connection monitor offload
The firmware supports periodic keep alive and beacon monitoring,
so advertise connection monitor offload capability by setting
IEEE80211_HW_CONNECTION_MONITOR flag. Implement missed beacons
notification handler. Call ieee80211_beacon_loss in case of
missed beacons, so AP probing by mac80211 can be triggered.
Alexander Bondar [Tue, 21 May 2013 11:49:09 +0000 (14:49 +0300)]
iwlwifi: mvm: Change number of DTIMs to skip semantics
If skip over DTIMs is enabled the driver can specify number of DTIMs
to skip. This parameter in host-device API implies number of DTIM
periods to skip. For example, to skip one DTIM means sleep over two
DTIM periods. Change semantics accordingly. Change this parameter's
default value.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Hante Meuleman [Mon, 27 May 2013 19:09:59 +0000 (21:09 +0200)]
brcmfmac: Disable powersave mode for P2P link.
For p2p client mode powersave mode should be kept disabled. It is
working but inefficient. In general p2p links do no benefit from this
mode, because these links are setup temporarily to transfer data.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Mon, 27 May 2013 19:09:58 +0000 (21:09 +0200)]
brcmfmac: Add multi channel support for P2P.
Multi channel support was disabled. This patch will enable it and
configure the P2P GO on the correct frequency when multi channel
is used.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 27 May 2013 19:09:57 +0000 (21:09 +0200)]
brcmfmac: use struct net_device::destructor to remove interfaces
Upon deleting a P2P_CLIENT/GO interface the vif and consequently
the wdev is freed before the net_device is actually being unregistered
but cfg80211 still needs to access the wdev. Using destructor field
to free the net_device and vif.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 27 May 2013 19:09:56 +0000 (21:09 +0200)]
brcmfmac: free net device when registration fails
When registration fails the net device is no longer needed. Free
the net device and remove reference to private data from the
driver.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 27 May 2013 19:09:55 +0000 (21:09 +0200)]
brcmfmac: add additional parameter to brcmf_free_vif()
Pass the struct brcmf_cfg80211_info instance instead of obtaining
through vif itself using vif->wdev. This is needed as the netdev
associated with this vif is already unregistered.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Mon, 27 May 2013 19:09:54 +0000 (21:09 +0200)]
brcmfmac: Fix p2p setup when connected to ap on 5G.
The firmware requires that on p2p setup when net interfaces
are created or updated that they start initially with the same
channel as the channel in use for the current connection
(if any). If none exists take default channel 11.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-beck.git / log