Currently ath9k_htc will reboot firmware only if interface was
ever started. Which lead to the problem in case where interface
was never started but module need to be reloaded.
This patch will partially fix bug "ath9k_htc: Target is unresponsive"
https://github.com/qca/open-ath9k-htc-firmware/issues/1
Reproduction case:
- plug adapter
- make sure nothing will touch it. Stop Networkmanager or blacklist mac address of this adapter.
- rmmod ath9k_htc; sleep 1; modprobe ath9k_htc
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Cc: <stable@vger.kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we configure harwdare and clock, only after
interface start. In this case, if we reload module or
reboot PC without configuring adapter, firmware will freeze.
There is no software way to reset adpter.
This patch add initial configuration and set it in
disabled state, to avoid this freeze. Behaviour of this patch
should be similar to: ifconfig wlan0 up; ifconfig wlan0 down.
Bug: https://github.com/qca/open-ath9k-htc-firmware/issues/1 Tested-by: Bo Shi <cnshibo@gmail.com> Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Cc: <stable@vger.kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake [Sat, 13 Jul 2013 14:57:10 +0000 (10:57 -0400)]
mwifiex: fix IRQ enable/disable
During tear down (e.g. mwifiex_sdio_remove during system suspend),
mwifiex left IRQs enabled for a significant period of time when it was
unable to handle them correctly. This caused interrupt storms and
interfered with the bluetooth interface on the same SDIO card.
Solve this by disabling interrupts at the point when they can no longer
be handled correctly, which is at the start of mwifiex_remove_card().
For cleanliness, we now enable interrupts in the mwifiex_add_card() path,
to be symmetrical with the disabling of interrupts. We also couple the
registration of the sdio IRQ handler with the actual enable/disable of
interrupts at the hardware level.
I also removed a write to this register in mwifiex_init_sdio which seemed
pointless and won't cause any ill effects now that we only register
the SDIO IRQ handler when we are ready to accept interrupts.
Includes some corrections from Amitkumar Karwar.
Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Fri, 12 Jul 2013 20:32:15 +0000 (15:32 -0500)]
rtlwifi: Fix build errors for unusual cases
The present build configuration for the rtlwifi family of drivers will
fail under two known conditions:
(1) If rtlwifi is selected without selecting any of the dependent drivers,
there are errors in the build.
(2) If the PCI drivers are built into the kernel and the USB drivers are modules,
or vice versa, there are missing globals.
The first condition is fixed by never building rtlwifi unless at least one
of the device drivers is selected. The second failure is fixed by splitting
the PCI and USB codes out of rtlwifi, and creating their own mini drivers.
If the drivers that use them are modules, they will also be modules.
Although a number of files are touched by this patch, only Makefile and Kconfig
have undergone significant changes. The only modifications to the other files
were to export entry points needed by the new rtl_pci and rtl_usb units, or to
rename two variables that had names that were likely to cause namespace collisions.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> [Condition 1] Reported-by: Ben Hutchings <bhutchings@solarflare.com> [Condition 2] Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Ben Hutchings <bhutchings@solarflare.com> Cc: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/built-in.o: In function `rt2x00queue_unmap_skb':
drivers/net/wireless/rt2x00/rt2x00queue.c:129: undefined reference to `dma_unmap_single'
drivers/net/wireless/rt2x00/rt2x00queue.c:133: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `rt2x00queue_map_txskb':
drivers/net/wireless/rt2x00/rt2x00queue.c:112: undefined reference to `dma_map_single'
drivers/net/wireless/rt2x00/rt2x00queue.c:115: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `rt2x00queue_alloc_rxskb':
drivers/net/wireless/rt2x00/rt2x00queue.c:93: undefined reference to `dma_map_single'
drivers/net/wireless/rt2x00/rt2x00queue.c:95: undefined reference to `dma_mapping_error'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: linux-wireless@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ARM OABI and EABI disagree on the alignment of structures
with small members, so module init tools may interpret the
ssb device table incorrectly, as shown by this warning when
building the b43 device driver in an OABI kernel:
FATAL: drivers/net/wireless/b43/b43: sizeof(struct ssb_device_id)=6 is
not a modulo of the size of section __mod_ssb_device_table=88.
Forcing the default (EABI) alignment on the structure makes this
problem go away. Since the ssb_device_id may have the same problem,
better fix both structures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Russell King <linux@arm.linux.org.uk> Cc: John W. Linville <linville@tuxdriver.com> Cc: Michael Buesch <mb@bu3sch.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_htc: fix data race between request_firmware_nowait() callback and suspend()
ath9k_hif_usb_probe() requests firmware asynchronically and
there is some initialization postponed till firmware is ready.
In particular, ath9k_hif_usb_firmware_cb() callback initializes
hif_dev->tx.tx_buf and hif_dev->tx.tx_pending lists.
At the same time, ath9k_hif_usb_suspend() iterates that lists through
ath9k_hif_usb_dealloc_urbs(). If suspend happens before request_firmware_nowait()
callback is called, it can lead to oops.
Similar issue could be in ath9k_hif_usb_disconnect(), but it is prevented
using hif_dev->fw_done completion and HIF_USB_READY flag. The patch extends
this approach to suspend() as well.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Fri, 28 Jun 2013 14:12:53 +0000 (09:12 -0500)]
rtlwifi: Initialize power-setting callback for USB devices
Commit a269913c5 entitled "rtlwifi: Rework rtl_lps_leave() and
rtl_lps_enter() to use work queue" has two bugs for USB drivers.
Firstly, the work queue in question was not initialized. Secondly,
the callback routine used by this queue is contained within the
file used for PCI devices. As a result, it is not available for
architectures without PCI hardware.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Reported-by: Richard Genoud <richard.genoud@gmail.com> Tested-by: Richard Genoud <richard.genoud@gmail.com> Cc: Richard Genoud <richard.genoud@gmail.com> Cc: Stable <stable@vger.kernel.org> [3.10] Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Spinadel [Thu, 4 Jul 2013 12:22:26 +0000 (15:22 +0300)]
iwlwifi: mvm: remove extra SSID from probe request
Bits 1-21 in this channel type attributes are indication for which
SSID is going to be sent on this channel. Since the first SSID is
sent implicitly in the probe request, we don't need to toggle its
bit here.
Signed-off-by: David Spinadel <david.spinadel@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
David Spinadel [Thu, 4 Jul 2013 12:17:48 +0000 (15:17 +0300)]
iwlwifi: mvm: fix bug in scan ssid
Increment index in each iteration. Without this increment we are
overriding the added SSIDs and we will send only the last SSId
and (n_ssids - 1) broadcast probes.
Cc: <stable@vger.kernel.org> [3.9+] Signed-off-by: David Spinadel <david.spinadel@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 4 Jul 2013 13:55:29 +0000 (15:55 +0200)]
iwlwifi: mvm: refuse connection to APs with BI < 16
Due to a firmware bug, it crashes when the beacon interval
is smaller than 16. Avoid this by refusing the station state
change creating the AP station, causing mac80211 to abandon
the attempt to connect to the AP, and eventually wpa_s to
blacklist it.
Cc: stable@vger.kernel.org Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 3 May 2013 16:58:16 +0000 (18:58 +0200)]
iwlwifi: dvm: don't send BT_CONFIG on devices w/o Bluetooth
The BT_CONFIG command that is sent to the device during
startup will enable BT coex unless the module parameter
turns it off, but on devices without Bluetooth this may
cause problems, as reported in Redhat BZ 885407.
Fix this by sending the BT_CONFIG command only when the
device has Bluetooth.
Cc: stable@vger.kernel.org Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Johannes Berg [Thu, 11 Jul 2013 20:33:26 +0000 (22:33 +0200)]
mac80211: fix duplicate retransmission detection
The duplicate retransmission detection code in mac80211
erroneously attempts to do the check for every frame,
even frames that don't have a sequence control field or
that don't use it (QoS-Null frames.)
This is problematic because it causes the code to access
data beyond the end of the SKB and depending on the data
there will drop packets erroneously.
Correct the code to not do duplicate detection for such
frames.
I found this error while testing AP powersave, it lead
to retransmitted PS-Poll frames being dropped entirely
as the data beyond the end of the SKB was always zero.
Cc: stable@vger.kernel.org [all versions] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
nl80211: fix the setting of RSSI threshold value for mesh
RSSI threshold value used for mesh peering should be in
negative value. After range checks to mesh parameters is
introduced, this is not allowed. Fix this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Johannes Berg [Mon, 8 Jul 2013 08:43:31 +0000 (10:43 +0200)]
mac80211: fix ethtool stats for non-station interfaces
As reported in https://bugzilla.kernel.org/show_bug.cgi?id=60514,
the station loop never initialises 'sinfo' and therefore adds up
a stack values, leaking stack information (the number of times it
adds values is easily obtained another way.)
Fix this by initialising the sinfo for each station to add.
Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Johannes Berg [Fri, 28 Jun 2013 09:38:54 +0000 (11:38 +0200)]
cfg80211: fix bugs in new SME implementation
When splitting the SME implementation from the MLME code,
I introduced a few bugs:
* association failures no longer sent a connect-failure event
* getting disassociated from the AP caused deauth to be sent
but state wasn't cleaned up, leading to warnings
* authentication failures weren't cleaned up properly, causing
new connection attempts to warn and fail
Fix these bugs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Michal Kazior [Tue, 25 Jun 2013 07:17:17 +0000 (09:17 +0200)]
nl80211: fix mgmt tx status and testmode reporting for netns
These two events were sent to the default network
namespace.
This caused AP mode in a non-default netns to not
work correctly. Mgmt tx status was multicasted to
a different (default) netns instead of the one the
AP was in.
Cc: stable@vger.kernel.org Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge branch 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux
Pull slab update from Pekka Enberg:
"Highlights:
- Fix for boot-time problems on some architectures due to
init_lock_keys() not respecting kmalloc_caches boundaries
(Christoph Lameter)
- CONFIG_SLUB_CPU_PARTIAL requested by RT folks (Joonsoo Kim)
- Fix for excessive slab freelist draining (Wanpeng Li)
- SLUB and SLOB cleanups and fixes (various people)"
I ended up editing the branch, and this avoids two commits at the end
that were immediately reverted, and I instead just applied the oneliner
fix in between myself.
* 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux
slub: Check for page NULL before doing the node_match check
mm/slab: Give s_next and s_stop slab-specific names
slob: Check for NULL pointer before calling ctor()
slub: Make cpu partial slab support configurable
slab: add kmalloc() to kernel API documentation
slab: fix init_lock_keys
slob: use DIV_ROUND_UP where possible
slub: do not put a slab to cpu partial list when cpu_partial is 0
mm/slub: Use node_nr_slabs and node_nr_objs in get_slabinfo
mm/slub: Drop unnecessary nr_partials
mm/slab: Fix /proc/slabinfo unwriteable for slab
mm/slab: Sharing s_next and s_stop between slab and slub
mm/slab: Fix drain freelist excessively
slob: Rework #ifdeffery in slab.h
mm, slab: moved kmem_cache_alloc_node comment to correct place
Now, this uses SLUB pretty much unmodified, but as it is the -rt kernel
with CONFIG_PREEMPT_RT set, spinlocks are mutexes, although they do
disable migration. But the SLUB code is relatively lockless, and the
spin_locks there are raw_spin_locks (not converted to mutexes), thus I
believe this bug can happen in mainline without -rt features. The -rt
patch is just good at triggering mainline bugs ;-)
Anyway, looking at where this crashed, it seems that the page variable
can be NULL when passed to the node_match() function (which does not
check if it is NULL). When this happens we get the above panic.
As page is only used in slab_alloc() to check if the node matches, if
it's NULL I'm assuming that we can say it doesn't and call the
__slab_alloc() code. Is this a correct assumption?
Acked-by: Christoph Lameter <cl@linux.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Pekka Enberg <penberg@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull more vfs stuff from Al Viro:
"O_TMPFILE ABI changes, Oleg's fput() series, misc cleanups, including
making simple_lookup() usable for filesystems with non-NULL s_d_op,
which allows us to get rid of quite a bit of ugliness"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
sunrpc: now we can just set ->s_d_op
cgroup: we can use simple_lookup() now
efivarfs: we can use simple_lookup() now
make simple_lookup() usable for filesystems that set ->s_d_op
configfs: don't open-code d_alloc_name()
__rpc_lookup_create_exclusive: pass string instead of qstr
rpc_create_*_dir: don't bother with qstr
llist: llist_add() can use llist_add_batch()
llist: fix/simplify llist_add() and llist_add_batch()
fput: turn "list_head delayed_fput_list" into llist_head
fs/file_table.c:fput(): add comment
Safer ABI for O_TMPFILE
Merge branch 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86
Pull x86 platform driver updates from Matthew Garrett:
"Nothing overly exciting here - a couple of new drivers that don't do a
great deal, along with some miscellaneous fixes and a couple of small
feature enablement patches"
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
x86 platform drivers: fix gpio leak
toshiba_acpi: Add dependency on SERIO_I8042
asus-nb-wmi: set wapf=4 for ASUSTeK COMPUTER INC. 1015E/U
Add trivial driver to disable Intel Smart Connect
Add support driver for Intel Rapid Start Technology
hp-wmi: add supports for POST code error
asus-wmi: control wlan-led only if wapf == 4
drivers/platform/x86/intel_ips: Convert to module_pci_driver
asus-nb-wmi: ignore ALS notification key code
asus-wmi: append newline to messages
x86: asus-laptop: fix invalid point access
x86: msi-laptop: fix memleak
amilo-rfkill: Add dependency on SERIO_I8042
dell-laptop: fix error return code in dell_init()
hp-wmi: Enable hotkeys on some systems
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull second round of input updates from Dmitry Torokhov:
"An update to Elantech driver to support hardware v7, fix to the new
cyttsp4 driver to use proper addressing, ads7846 device tree support
and nspire-keypad got a small cleanup."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: nspire-keypad - replace magic offset with define
Input: elantech - fix for newer hardware versions (v7)
Input: cyttsp4 - use 16bit address for I2C/SPI communication
Input: ads7846 - add device tree bindings
Input: ads7846 - make sure we do not change platform data
Pull networking fixes from David Miller:
"Just a bunch of small fixes and tidy ups:
1) Finish the "busy_poll" renames, from Eliezer Tamir.
2) Fix RCU stalls in IFB driver, from Ding Tianhong.
3) Linearize buffers properly in tun/macvtap zerocopy code.
4) Don't crash on rmmod in vxlan, from Pravin B Shelar.
5) Spinlock used before init in alx driver, from Maarten Lankhorst.
6) A sparse warning fix in bnx2x broke TSO checksums, fix from Dmitry
Kravkov.
7) Dummy and ifb driver load failure paths can oops, fixes from Tan
Xiaojun and Ding Tianhong.
8) Correct MTU calculations in IP tunnels, from Alexander Duyck.
9) Account all TCP retransmits in SNMP stats properly, from Yuchung
Cheng.
10) atl1e and via-rhine do not handle DMA mapping failures properly,
from Neil Horman.
11) Various equal-cost multipath route fixes in ipv6 from Hannes
Frederic Sowa"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
ipv6: only static routes qualify for equal cost multipathing
via-rhine: fix dma mapping errors
atl1e: fix dma mapping warnings
tcp: account all retransmit failures
usb/net/r815x: fix cast to restricted __le32
usb/net/r8152: fix integer overflow in expression
net: access page->private by using page_private
net: strict_strtoul is obsolete, use kstrtoul instead
drivers/net/ieee802154: don't use devm_pinctrl_get_select_default() in probe
drivers/net/ethernet/cadence: don't use devm_pinctrl_get_select_default() in probe
drivers/net/can/c_can: don't use devm_pinctrl_get_select_default() in probe
net/usb: add relative mii functions for r815x
net/tipc: use %*phC to dump small buffers in hex form
qlcnic: Adding Maintainers.
gre: Fix MTU sizing check for gretap tunnels
pkt_sched: sch_qfq: remove forward declaration of qfq_update_agg_ts
pkt_sched: sch_qfq: improve efficiency of make_eligible
gso: Update tunnel segmentation to support Tx checksum offload
inet: fix spacing in assignment
ifb: fix oops when loading the ifb failed
...
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull final round of SCSI updates from James Bottomley:
"This is the remaining set of SCSI patches for the merge window. It's
mostly driver updates (scsi_debug, qla2xxx, storvsc, mp3sas). There
are also several bug fixes in fcoe, libfc, and megaraid_sas. We also
have a couple of core changes to try to make device destruction more
deterministic"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (46 commits)
[SCSI] scsi constants: command, sense key + additional sense strings
fcoe: Reduce number of sparse warnings
fcoe: Stop fc_rport_priv structure leak
libfcoe: Fix meaningless log statement
libfc: Differentiate echange timer cancellation debug statements
libfc: Remove extra space in fc_exch_timer_cancel definition
fcoe: fix the link error status block sparse warnings
fcoe: Fix smatch warning in fcoe_fdmi_info function
libfc: Reject PLOGI from nodes with incompatible role
[SCSI] enable destruction of blocked devices which fail LUN scanning
[SCSI] Fix race between starved list and device removal
[SCSI] megaraid_sas: fix a bug for 64 bit arches
[SCSI] scsi_debug: reduce duplication between prot_verify_read and prot_verify_write
[SCSI] scsi_debug: simplify offset calculation for dif_storep
[SCSI] scsi_debug: invalidate protection info for unmapped region
[SCSI] scsi_debug: fix NULL pointer dereference with parameters dif=0 dix=1
[SCSI] scsi_debug: fix incorrectly nested kmap_atomic()
[SCSI] scsi_debug: fix invalid address passed to kunmap_atomic()
[SCSI] mpt3sas: Bump driver version to v02.100.00.00
[SCSI] mpt3sas: when async scanning is enabled then while scanning, devices are removed but their transport layer entries are not removed
...
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
- core fix for missing round up in the generic irq chip implementation
- new irq chip for MOXA SoCs
- a few fixes and cleanups in the irqchip drivers
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Add support for MOXA ART SoCs
genirq: generic chip: Use DIV_ROUND_UP to calculate numchips
irqchip: nvic: Fix wrong num_ct argument for irq_alloc_domain_generic_chips()
irqchip: sun4i: Staticize sun4i_irq_ack()
irqchip: vt8500: Staticize local symbols
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
- watchdog fixes for full dynticks
- improved debug output for full dynticks
- remove an obsolete full dynticks check
- two ARM SoC clocksource drivers for sharing across SoCs
- tick broadcast fix for CPU hotplug
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: broadcast: Check broadcast mode on CPU hotplug
clocksource: arm_global_timer: Add ARM global timer support
clocksource: Add Marvell Orion SoC timer
nohz: Remove obsolete check for full dynticks CPUs to be RCU nocbs
watchdog: Boot-disable by default on full dynticks
watchdog: Rename confusing state variable
watchdog: Register / unregister watchdog kthreads on sysctl control
nohz: Warn if the machine can not perform nohz_full
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is our first set of fixes from arm-soc for 3.11.
- A handful of build and warning fixes from Arnd
- A collection of OMAP fixes
- defconfig updates to make the default configs more useful for real
use (and testing) out of the box on hardware
And a couple of other small fixes. Some of these have been recently
applied but it's normally how we deal with fixes, with less bake time
in -next needed"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
arm: multi_v7_defconfig: Tweaks for omap and sunxi
arm: multi_v7_defconfig: add i.MX options and NFS root
ARM: omap2: add select of TI_PRIV_EDMA
ARM: exynos: select PM_GENERIC_DOMAINS only when used
ARM: ixp4xx: avoid circular header dependency
ARM: OMAP: omap_common_late_init may be unused
ARM: sti: move DEBUG_STI_UART into alphabetical order
ARM: OMAP: build mach-omap code only if needed
ARM: zynq: use DT_MACHINE_START
ARM: omap5: omap5 has SCU and TWD
ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
ARM: OMAP2+: devices: remove duplicated include from devices.c
ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
ARM: OMAP2+: Remove obsolete Makefile line
ARM: OMAP5: Enable Cortex A15 errata 798181
...
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"A few fixes for ARM, mostly just one liners with the exception of the
missing section specification. We decided not to rely on .previous to
fix this but to explicitly state the section we want the code to be
in."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7778/1: smp_twd: twd_update_frequency need be run on all online CPUs
ARM: 7782/1: Kconfig: Let ARM_ERRATA_364296 not depend on CONFIG_SMP
ARM: mm: fix boot on SA1110 Assabet
ARM: 7781/1: mmu: Add debug_ll_io_init() mappings to early mappings
ARM: 7780/1: add missing linker section markup to head-common.S
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
Pull watchdog updates from Wim Van Sebroeck:
- lots of devm_ conversions and cleanup
- platform_set_drvdata cleanups
- s3c2410: dev_err/dev_info + dev_pm_ops
- watchdog_core: don't try to stop device if not running fix
- wdrtas: use print_hex_dump
- xilinx cleanups
- orion_wdt fixes
- softdog cleanup
- hpwdt: check on UEFI bits
- deletion of mpcore_wdt driver
- addition of broadcom BCM2835 watchdog timer driver
- addition of MEN A21 watcdog devices
* git://www.linux-watchdog.org/linux-watchdog: (38 commits)
watchdog: hpwdt: Add check for UEFI bits
watchdog: softdog: remove replaceable ping operation
watchdog: New watchdog driver for MEN A21 watchdogs
Watchdog: fix clearing of the watchdog interrupt
Watchdog: allow orion_wdt to be built for Dove
watchdog: Add Broadcom BCM2835 watchdog timer driver
watchdog: delete mpcore_wdt driver
watchdog: xilinx: Setup the origin compatible string
watchdog: xilinx: Fix driver header
watchdog: wdrtas: don't use custom version of print_hex_dump
watchdog: core: don't try to stop device if not running
watchdog: jz4740: Pass device to clk_get
watchdog: twl4030: Remove redundant platform_set_drvdata()
watchdog: mpcore: Remove redundant platform_set_drvdata()
watchdog: da9055: use platform_{get,set}_drvdata()
watchdog: da9052: use platform_{get,set}_drvdata()
watchdog: cpwd: use platform_{get,set}_drvdata()
watchdog: s3c2410_wdt: convert s3c2410wdt to dev_pm_ops
watchdog: s3c2410_wdt: use dev_err()/dev_info() instead of pr_err()/pr_info()
watchdog: wm831x: use platform_{get,set}_drvdata()
...
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- AF_IB (native IB addressing) for CMA from Sean Hefty
- new mlx5 driver for Mellanox Connect-IB adapters (including post
merge request fixes)
- SRP fixes from Bart Van Assche (including fix to first merge request)
- qib HW driver updates
- resurrection of ocrdma HW driver development
- uverbs conversion to create fds with O_CLOEXEC set
- other small changes and fixes
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (66 commits)
mlx5: Return -EFAULT instead of -EPERM
IB/qib: Log all SDMA errors unconditionally
IB/qib: Fix module-level leak
mlx5_core: Adjust hca_cap.uar_page_sz to conform to Connect-IB spec
IB/srp: Let srp_abort() return FAST_IO_FAIL if TL offline
IB/uverbs: Use get_unused_fd_flags(O_CLOEXEC) instead of get_unused_fd()
mlx5_core: Fixes for sparse warnings
IB/mlx5: Make profile[] static in main.c
mlx5: Fix parameter type of health_handler_t
mlx5: Add driver for Mellanox Connect-IB adapters
IB/core: Add reserved values to enums for low-level driver use
IB/srp: Bump driver version and release date
IB/srp: Make HCA completion vector configurable
IB/srp: Maintain a single connection per I_T nexus
IB/srp: Fail I/O fast if target offline
IB/srp: Skip host settle delay
IB/srp: Avoid skipping srp_reset_host() after a transport error
IB/srp: Fix remove_one crash due to resource exhaustion
IB/qib: New transmitter tunning settings for Dell 1.1 backplane
IB/core: Fix error return code in add_port()
...
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"This series contain:
- new i2c video drivers: ml86v7667 (video decoder),
ths8200 (video encoder)
- a new video driver for EasyCap cards based on Fushicai USBTV007
- Improved support for OF and embedded systems, with V4L2 async
initialization and a better support for clocks
- API cleanups on the ioctls used by the v4l2 debug tool
- Lots of cleanups
- As usual, several driver improvements and new cards additions
- Revert two changesets that change the minimal symbol rate for
stv0399, as request by Manu
- Update MAINTAINERS and other files to point to my new e-mail"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (378 commits)
MAINTAINERS & ABI: Update to point to my new email
[media] stb0899: restore minimal rate to 5Mbauds
[media] exynos4-is: Correct colorspace handling at FIMC-LITE
[media] exynos4-is: Set valid initial format on FIMC.n subdevs
[media] exynos4-is: Set valid initial format on FIMC-IS-ISP subdev pads
[media] exynos4-is: Fix format propagation on FIMC-IS-ISP subdev
[media] exynos4-is: Set valid initial format at FIMC-LITE
[media] exynos4-is: Fix format propagation on FIMC-LITE.n subdevs
[media] MAINTAINERS: Update S5P/Exynos FIMC driver entry
[media] Documentation: Update driver's directory in video4linux/fimc.txt
[media] exynos4-is: Change fimc-is firmware file names
[media] exynos4-is: Add support for Exynos5250 MIPI-CSIS
[media] exynos4-is: Add Exynos5250 SoC support to fimc-lite driver
[media] exynos4-is: Drop drvdata handling in fimc-lite for non-dt platforms
[media] media: i2c: tvp514x: remove manual setting of subdev name
[media] media: i2c: tvp7002: remove manual setting of subdev name
[media] mem2mem: set missing v4l2_dev pointer
[media] wl128x: add missing struct v4l2_device
[media] tvp514x: Fix init seqeunce
[media] saa7134: Fix sparse warnings by adding __user annotation
...
Merge tag 'for-linus-v3.11-rc1-2' of git://oss.sgi.com/xfs/xfs
Pull more xfs updates from Ben Myers:
"Here are a fix for xfs_fsr, a cleanup in bulkstat, a cleanup in
xfs_open_by_handle, updated mount options documentation, a cleanup in
xfs_bmapi_write, a fix for the size of dquot log reservations, a fix
for sgid inheritance when acls are in use, a fix for cleaning up
quotainfo structures, and some more of the work which allows group and
project quotas to be used together.
We had a few more in this last quota category that we might have liked
to get in, but it looks there are still a few items that need to be
addressed.
- fix for xfs_fsr returning -EINVAL
- cleanup in xfs_bulkstat
- cleanup in xfs_open_by_handle
- update mount options documentation
- clean up local format handling in xfs_bmapi_write
- fix dquot log reservations which were too small
- fix sgid inheritance for subdirectories when default acls are in use
- add project quota fields to various structures
- fix teardown of quotainfo structures when quotas are turned off"
* tag 'for-linus-v3.11-rc1-2' of git://oss.sgi.com/xfs/xfs:
xfs: Fix the logic check for all quotas being turned off
xfs: Add pquota fields where gquota is used.
xfs: fix sgid inheritance for subdirectories inheriting default acls [V3]
xfs: dquot log reservations are too small
xfs: remove local fork format handling from xfs_bmapi_write()
xfs: update mount options documentation
xfs: use get_unused_fd_flags(0) instead of get_unused_fd()
xfs: clean up unused codes at xfs_bulkstat()
xfs: use XFS_BMAP_BMDR_SPACE vs. XFS_BROOT_SIZE_ADJ
Merge branch 'for-linus' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Fixes for 4 cifs bugs, including a reconnect problem, a problem
parsing responses to SMB2 open request, and setting nlink incorrectly
to some servers which don't report it properly on the wire. Also
improves data integrity on reconnect with series from Pavel which adds
durable handle support for SMB2."
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix a deadlock when a file is reopened
CIFS: Reopen the file if reconnect durable handle failed
[CIFS] Fix minor endian error in durable handle patch series
CIFS: Reconnect durable handles for SMB2
CIFS: Make SMB2_open use cifs_open_parms struct
CIFS: Introduce cifs_open_parms struct
CIFS: Request durable open for SMB2 opens
CIFS: Simplify SMB2 create context handling
CIFS: Simplify SMB2_open code path
CIFS: Respect create_options in smb2_open_file
CIFS: Fix lease context buffer parsing
[CIFS] use sensible file nlink values if unprovided
Limit allocation of crypto mechanisms to dialect which requires
llist_add(new, head) can simply use llist_add_batch(new, new, head),
no need to duplicate the code.
This obviously uninlines llist_add() and to me this is a win. But we
can make llist_add_batch() inline if this is desirable, in this case
gcc can notice that new_first == new_last if the caller is llist_add().
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Andrey Vagin <avagin@openvz.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: David Howells <dhowells@redhat.com> Cc: Huang Ying <ying.huang@intel.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
llist: fix/simplify llist_add() and llist_add_batch()
1. This is mostly theoretical, but llist_add*() need ACCESS_ONCE().
Otherwise it is not guaranteed that the first cmpxchg() uses the
same value for old_entry and new_last->next.
2. These helpers cache the result of cmpxchg() and read the initial
value of head->first before the main loop. I do not think this
makes sense. In the likely case cmpxchg() succeeds, otherwise
it doesn't hurt to reload head->first.
I think it would be better to simplify the code and simply read
->first before cmpxchg().
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Andrey Vagin <avagin@openvz.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: David Howells <dhowells@redhat.com> Cc: Huang Ying <ying.huang@intel.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sat, 13 Jul 2013 09:26:37 +0000 (13:26 +0400)]
Safer ABI for O_TMPFILE
[suggested by Rasmus Villemoes] make O_DIRECTORY | O_RDWR part of O_TMPFILE;
that will fail on old kernels in a lot more cases than what I came up with.
And make sure O_CREAT doesn't get there...
James Bottomley [Sat, 13 Jul 2013 04:22:56 +0000 (08:22 +0400)]
Merge tag 'fcoe' into for-linus
A short series of fixes to libfc, libfcoe and fcoe.
Most patches fix formatting problems, one changes
the behavior of which discovered ports can/will be
logged into and another fixes a memory leak.
ipv6: only static routes qualify for equal cost multipathing
Static routes in this case are non-expiring routes which did not get
configured by autoconf or by icmpv6 redirects.
To make sure we actually get an ecmp route while searching for the first
one in this fib6_node's leafs, also make sure it matches the ecmp route
assumptions.
v2:
a) Removed RTF_EXPIRE check in dst.from chain. The check of RTF_ADDRCONF
already ensures that this route, even if added again without
RTF_EXPIRES (in case of a RA announcement with infinite timeout),
does not cause the rt6i_nsiblings logic to go wrong if a later RA
updates the expiration time later.
v3:
a) Allow RTF_EXPIRES routes to enter the ecmp route set. We have to do so,
because an pmtu event could update the RTF_EXPIRES flag and we would
not count this route, if another route joins this set. We now filter
only for RTF_GATEWAY|RTF_ADDRCONF|RTF_DYNAMIC, which are flags that
don't get changed after rt6_info construction.
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Usual problem with the usual fix, add the appropriate calls to dma_mapping_error
where appropriate
Untested, as I don't have hardware, but its pretty straightforward
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: David S. Miller <davem@davemloft.net> CC: Roger Luethi <rl@hellgate.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
The usual straighforward failure to check for dma_mapping_error after a map
operation is completed.
This patch should fix it, the reporter wandered off after filing this bz:
https://bugzilla.redhat.com/show_bug.cgi?id=954170
and I don't have hardware to test, but the fix is pretty straightforward, so I
figured I'd post it for review.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Jay Cliburn <jcliburn@gmail.com> CC: Chris Snook <chris.snook@gmail.com> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Change snmp RETRANSFAILS stat to include timeout retransmit failures
in addition to other loss recoveries.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
>> drivers/net/usb/r815x.c:38:16: sparse: cast to restricted __le32
>> drivers/net/usb/r815x.c:67:15: sparse: cast to restricted __le32
>> drivers/net/usb/r815x.c:69:13: sparse: incorrect type in assignment (different base types)
drivers/net/usb/r815x.c:69:13: expected unsigned int [unsigned] [addressable] [assigned] [usertype] tmp
drivers/net/usb/r815x.c:69:13: got restricted __le32 [usertype] <noident>
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Spotted-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
config: make ARCH=avr32 allyesconfig
drivers/net/usb/r8152.c: In function 'rtl8152_start_xmit':
drivers/net/usb/r8152.c:956: warning: integer overflow in expression
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Spotted-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Olof Johansson [Fri, 12 Jul 2013 18:06:01 +0000 (11:06 -0700)]
Merge tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij:
Ux500 defconfig changes:
- Update base due to different Kconfig changes
- Select watchdog, MUSB, Ux500 ALSA SoC, various MMC/SD
features and enable highmem
* tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Enable HIGHMEM in the u8500 defconfig
ARM: ux500: Update MMC configs for u8500 defconfig
ARM: ux500: select SND_SOC_UX500 for ux500
ARM: ux500: update defconfig base
ARM: ux500: select WATCHDOG and MUSB for ux500
Vincent Stehlé [Wed, 3 Jul 2013 08:12:58 +0000 (10:12 +0200)]
arm: multi_v7_defconfig: add i.MX options and NFS root
- Add i.MX serial console support. This gives us the boot messages on
UART on e.g. the i.MX6Q sabre sd platform.
- Add the necessary config options, to allow booting with NFS root on
an i.MX6 sabre sd.
- Add Freescale LPUART serial console support. This gives us the boot
messages on UART on e.g. the Vybrid VF610 Tower board.
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com> Cc: Russell King <linux@arm.linux.org.uk>
[olof: squashed three commits down to one] Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 12 Jul 2013 17:59:39 +0000 (10:59 -0700)]
Merge tag 'omap-for-v3.11/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Omap fixes and minor defconfig updates that would be good to
get in before -rc1.
* tag 'omap-for-v3.11/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
ARM: OMAP2+: devices: remove duplicated include from devices.c
ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
ARM: OMAP2+: Remove obsolete Makefile line
ARM: OMAP5: Enable Cortex A15 errata 798181
ARM: scu: provide inline dummy functions when SCU is not present
ARM: OMAP4: sleep: build OMAP4 specific functions only for OMAP4
ARM: OMAP2+: timer: initialize before using oh_name
Signed-off-by: Olof Johansson <olof@lixom.net>
Add/move/change conflicts in arch/arm/mach-omap2/Kconfig resolved.
Dave Hansen [Mon, 8 Jul 2013 21:44:04 +0000 (14:44 -0700)]
perf/x86: Fix incorrect use of do_div() in NMI warning
I completely botched understanding the calling conventions of
do_div(). I assumed that do_div() returned the result instead
of realizing that it modifies its argument and returns a
remainder. The side-effect from this would be bogus numbers
for the "msecs" value in the warning messages:
INFO: NMI handler (perf_event_nmi_handler) took too long to run: 0.114 msecs
Note, there was a second fix posted by Stephane Eranian for
a separate patch which I also botched:
Peter Zijlstra [Fri, 28 Jun 2013 09:18:53 +0000 (11:18 +0200)]
sched: Fix HRTICK
David reported that the HRTICK sched feature was borken; which was enough
motivation for me to finally fix it ;-)
We should not allow hrtimer code to do softirq wakeups while holding scheduler
locks. The hrtimer code only needs this when we accidentally try to program an
expired time. We don't much care about those anyway since we have the regular
tick to fall back to.
Stephen Boyd [Thu, 11 Jul 2013 14:00:59 +0000 (07:00 -0700)]
tick: broadcast: Check broadcast mode on CPU hotplug
On ARM systems the dummy clockevent is registered with the cpu
hotplug notifier chain before any other per-cpu clockevent. This
has the side-effect of causing the dummy clockevent to be
registered first in every hotplug sequence. Because the dummy is
first, we'll try to turn the broadcast source on but the code in
tick_device_uses_broadcast() assumes the broadcast source is in
periodic mode and calls tick_broadcast_start_periodic()
unconditionally.
On boot this isn't a problem because we typically haven't
switched into oneshot mode yet (if at all). During hotplug, if
the broadcast source isn't in periodic mode we'll replace the
broadcast oneshot handler with the broadcast periodic handler and
start emulating oneshot mode when we shouldn't. Due to the way
the broadcast oneshot handler programs the next_event it's
possible for it to contain KTIME_MAX and cause us to hang the
system when the periodic handler tries to program the next tick.
Fix this by using the appropriate function to start the broadcast
source.
Reported-by: Stephen Warren <swarren@nvidia.com> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Cc: Mark Rutland <Mark.Rutland@arm.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: ARM kernel mailing list <linux-arm-kernel@lists.infradead.org> Cc: John Stultz <john.stultz@linaro.org> Cc: Joseph Lo <josephl@nvidia.com> Link: http://lkml.kernel.org/r/20130711140059.GA27430@codeaurora.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Peter Zijlstra [Fri, 12 Jul 2013 09:08:33 +0000 (11:08 +0200)]
perf: Fix perf_lock_task_context() vs RCU
Jiri managed to trigger this warning:
[] ======================================================
[] [ INFO: possible circular locking dependency detected ]
[] 3.10.0+ #228 Tainted: G W
[] -------------------------------------------------------
[] p/6613 is trying to acquire lock:
[] (rcu_node_0){..-...}, at: [<ffffffff810ca797>] rcu_read_unlock_special+0xa7/0x250
[]
[] but task is already holding lock:
[] (&ctx->lock){-.-...}, at: [<ffffffff810f2879>] perf_lock_task_context+0xd9/0x2c0
[]
[] which lock already depends on the new lock.
[]
[] the existing dependency chain (in reverse order) is:
[]
[] -> #4 (&ctx->lock){-.-...}:
[] -> #3 (&rq->lock){-.-.-.}:
[] -> #2 (&p->pi_lock){-.-.-.}:
[] -> #1 (&rnp->nocb_gp_wq[1]){......}:
[] -> #0 (rcu_node_0){..-...}:
Paul was quick to explain that due to preemptible RCU we cannot call
rcu_read_unlock() while holding scheduler (or nested) locks when part
of the read side critical section was preemptible.
Therefore solve it by making the entire RCU read side non-preemptible.
Also pull out the retry from under the non-preempt to play nice with RT.
Reported-by: Jiri Olsa <jolsa@redhat.com> Helped-out-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: <stable@kernel.org> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jiri Olsa [Tue, 9 Jul 2013 15:44:11 +0000 (17:44 +0200)]
perf: Remove WARN_ON_ONCE() check in __perf_event_enable() for valid scenario
The '!ctx->is_active' check has a valid scenario, so
there's no need for the warning.
The reason is that there's a time window between the
'ctx->is_active' check in the perf_event_enable() function
and the __perf_event_enable() function having:
- IRQs on
- ctx->lock unlocked
where the task could be killed and 'ctx' deactivated by
perf_event_exit_task(), ending up with the warning below.
So remove the WARN_ON_ONCE() check and add comments to
explain it all.
This addresses the following warning reported by Vince Weaver:
Jiri Olsa [Tue, 9 Jul 2013 15:44:10 +0000 (17:44 +0200)]
perf: Clone child context from parent context pmu
Currently when the child context for inherited events is
created, it's based on the pmu object of the first event
of the parent context.
This is wrong for the following scenario:
- HW context having HW and SW event
- HW event got removed (closed)
- SW event stays in HW context as the only event
and its pmu is used to clone the child context
The issue starts when the cpu context object is touched
based on the pmu context object (__get_cpu_context). In
this case the HW context will work with SW cpu context
ending up with following WARN below.
Fixing this by using parent context pmu object to clone
from child context.
Addresses the following warning reported by Vince Weaver:
Wolfram Sang [Wed, 10 Jul 2013 15:57:44 +0000 (16:57 +0100)]
drivers/net/ieee802154: don't use devm_pinctrl_get_select_default() in probe
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13) Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Wolfram Sang [Wed, 10 Jul 2013 15:57:43 +0000 (16:57 +0100)]
drivers/net/ethernet/cadence: don't use devm_pinctrl_get_select_default() in probe
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13) Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wolfram Sang [Wed, 10 Jul 2013 15:57:42 +0000 (16:57 +0100)]
drivers/net/can/c_can: don't use devm_pinctrl_get_select_default() in probe
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13) Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Base on cdc_ether, add the mii functions for RTL8152 and RTL8153.
The RTL8152 and RTL8153 support ECM mode which use the driver of
cdc_ether. Add the mii functions. Then, the basic PHY access is
possible.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 10 Jul 2013 10:58:59 +0000 (13:58 +0300)]
mlx5: Return -EFAULT instead of -EPERM
For copy_to/from_user() failure, the correct error code is -EFAULT not
-EPERM.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Dean Luick [Thu, 11 Jul 2013 19:32:14 +0000 (15:32 -0400)]
IB/qib: Log all SDMA errors unconditionally
This patch adds code to log SDMA errors for supportability purposes.
Signed-off-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
The vzalloc()'ed field physshadow is leaked on module unload.
This patch adds vfree after the sibling page shadow is freed.
Reported-by: Dean Luick <dean.luick@intel.com> Reviewed-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
mlx5_core: Adjust hca_cap.uar_page_sz to conform to Connect-IB spec
Sparse reported an endianness bug in the assignment to hca_cap.uar_page_sz.
Fix the declaration of this field to be __be16 (which is what is in
the firmware spec), renaming the field to log_uar_pg_size to conform
to the spec, which fixes the endianness bug reported by sparse.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Moshe Lazer <moshel@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
IB/srp: Let srp_abort() return FAST_IO_FAIL if TL offline
If the transport layer is offline it is more appropriate to let
srp_abort() return FAST_IO_FAIL instead of SUCCESS.
Reported-by: Sebastian Riemer <sebastian.riemer@profitbricks.com> Acked-by: David Dillow <dillowda@ornl.gov> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Roland Dreier <roland@purestorage.com>
projects / linux-beck.git / log