Tejun Heo [Sun, 18 Mar 2007 13:26:53 +0000 (22:26 +0900)]
ahci: move port_map handling to ahci_save_initial_config()
Move cross checking between port_map and cap.n_ports into
ahci_save_initial_config(). After save_initial_config is done,
hpriv->port_map is always setup properly.
Tested on JMB363, ICH7 and ICH8 (with dummy ports).
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Sun, 18 Mar 2007 13:15:33 +0000 (22:15 +0900)]
ahci: implement ata_save/restore_initial_config()
There are several registers which describe how the controller is
configured. These registers are sometimes implemented as r/w
registers which are configured by firmware and get cleared on
controller reset or after suspend/resume cycle. ahci saved and
restored those values inside ahci_reset_controller() which is a bit
messy and doesn't work over suspend/resume cycle.
This patch implements ahci_save/restore_initial_config(). The save
function is called during driver initialization and saves cap and
port_map to hpriv. The restore function is called after the
controller is reset to restore the initial values.
Sometimes the initial firmware values are inconsistent and need to be
fixed up. This is handled by ahci_save_initial_config(). For this,
there are two versions of saved registers. One to write back to the
hardware register, the other to use during driver operation. This is
necessary to keep ahci's behavior unchanged (write back fixed up
port_map while keeping cap as-is).
This patch makes ahci save the register values once before the first
controller reset, not after it's been reset. Also, the same stored
values are used written back after each reset, so the register values
are properly recovered after suspend/resume cycle.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Promise ATA ports should always be reset by pdc_reset_port()
when errors are detected, but the recent error reason decoding
update to sata_promise replaced that reset with a freeze.
This patch changes the error detection to do a reset again.
This makes the error decoding update safer, as it now only
adds error decoding without changing any other behaviour.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Tue, 10 Apr 2007 23:19:00 +0000 (00:19 +0100)]
pata_pdc2027x: Updates
Signed-off-by: Alan Cox <alan@redhat.com>
Correct missing modefilter (crash if BAR4 unassigned)
Use Cable Detect method
Wrap ->set_mode instead ready for ->post_set_mode removal
Maxtor errata as per Jeff Garzik report
Remove duplicated private udma_mask hacking Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark Lord [Fri, 16 Mar 2007 14:22:26 +0000 (10:22 -0400)]
libata: add support for READ/WRITE LONG
The READ/WRITE LONG commands are theoretically obsolete,
but the majority of drives in existance still implement them.
The WRITE_LONG and WRITE_LONG_ONCE commands are of particular
interest for fault injection testing -- eg. creating "media errors"
at specific locations on a disk.
The fussy bit is that these commands require a non-standard
sector size, usually 520 bytes instead of 512.
This patch adds support to libata for READ/WRITE LONG commands
issued via SG_IO/ATA_16.
Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add notation that the Asus W5F laptop has a short cable instead of 80-wire.
The Asus W5F laptop uses a short cable instead of the 80-wire style, and thus
needs to be in the ich_laptop special cases for correct detection and support
of UDMA/100 for the hard drive. I noticed this because I have the W5F laptop,
and was tracing apparent slowness.
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Tue, 27 Mar 2007 05:43:43 +0000 (21:43 -0800)]
pata_optidma: rework for cable detect and to remove post_set_mode()
A lot of noise because I had to rename the optidma_set_mode() method to
avoid confusion with the new ->set_mode() method that was added. Cable
detect side is pretty trivial.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Tue, 27 Mar 2007 05:43:40 +0000 (21:43 -0800)]
pata_qdI: restore cable detect
Signed-off-by: Alan Cox <number6@the-village.bc.nu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Robert Hancock [Tue, 27 Mar 2007 05:43:36 +0000 (21:43 -0800)]
sata_nv: don't read shadow registers when in ADMA mode
Reading from the ATA shadow registers while we are in ADMA mode may cause
undefined behavior. Don't read the ATA status register when completing
commands for this reason, it shouldn't be needed as the controller will
notify us if the command failed. Also, don't allow commands with result
taskfile requested to execute in ADMA mode, since that requires accessing
the shadow registers. We also still need to override tf_read since libata
will read the result taskfile on a command failure, and we need to go into
port register mode before allowing this.
Signed-off-by: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan [Tue, 27 Mar 2007 05:43:34 +0000 (21:43 -0800)]
pcmcia - spot slave decode flaws (for testing)
It tries to spot when the slave is a mirror of the master and to fix up
problems that causes.
I've got two confirmations so far that this plus the "can fail set_xfer" patch
work for folks who had problems before. Also if you are unfortunate enough to
be running something like HAL then it'll automount the same disk twice for you
and corrupt it without the fix (aint that nice...)
Tested (successfully) by Komuro <komurojun-mbn@nifty.com>.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Andrew Morton [Mon, 26 Mar 2007 09:17:43 +0000 (02:17 -0700)]
git-libata-all-ipr-fix
drivers/scsi/ipr.c: In function '__ipr_eh_dev_reset':
drivers/scsi/ipr.c:3865: warning: passing argument 4 of 'ata_do_eh' from incompatible pointer type
Cc: Tejun Heo <htejun@gmail.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Tue, 13 Mar 2007 16:20:51 +0000 (01:20 +0900)]
libata: hardreset on SERR_INTERNAL
There was a rare report where SB600 reported SERR_INTERNAL and SRST
couldn't get it out of the failure mode. Hardreset on SERR_INTERNAL.
As the problem is intermittent, whether this fixes the problem or not
hasn't been verified yet, but hardresetting the channel on internal
error is a good idea anyway.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds much needed error reason decoding and
reporting to sata_promise. It's simplistic but should
log all relevant error info the controller provides.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch changes sata_promise so that the PATA ports
on TX2plus chips are bound to the pdc_pata_ops structure.
This means that operations called from the SATA ops
structures don't need any SATA-vs-PATA tests any more.
Instead, operations that depend on a port being SATA or
PATA are separated into different procedures.
* pdc_cable_type() is split into a PATA version and a
SATA version
* pdc_error_handler() is split into a PATA version and a
SATA version, that both call a common version after
setting up the `hardreset' function pointer
* pdc_old_check_atapi_dma() is now only used for SATAI
ports, so is renamed to pdc_old_sata_check_atapi_dma()
and simplified
* pdc_sata_scr_{read,write}() are now only used for SATA
ports, so their is-not-SATA tests are removed
* pdc_port_start() is split into three procedures: a wrapper
which performs the ->ops adjustment on TX2plus PATA ports,
a procedure with the common code, and a procedure with
the SATA-specific code (this bit might be cleaned up by
Tejun's new init model)
Tested on 20619, 20575, and 20775 chips.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
The recent change which moved cable detection from
pdc_pre_reset() to the new ->cable_detect hook only
added the hook for SATAII chips, leaving SATAI chips
and the 20619 without the hook. Fixed by this patch.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jeff Garzik [Fri, 9 Mar 2007 15:54:42 +0000 (10:54 -0500)]
libata/IDE: remove combined mode quirk
Both old-IDE and libata should be able handle all controllers and
devices found using normal resource reservation methods.
This eliminates the awful, low-performing split-driver configuration
where old-IDE drove the PATA portion of a PCI device, in PIO-only mode,
and libata drove the SATA portion of the /same/ PCI device, in DMA mode.
Typically vendors would ship SATA hard drive / PATA optical
configuration, which would lend itself to slow (PIO-only) CD-ROM
performance.
For Intel users running in combined mode, it is now wholly dependent on
your driver choice (potentially link order, if you compile both drivers
in) whether old-IDE or libata will drive your hardware.
In either case, you will get full performance from both SATA and PATA
ports now, without having to pass a kernel command line parameter.
Alan Cox [Fri, 9 Mar 2007 14:34:07 +0000 (09:34 -0500)]
libata: Change prototype of mode_filter to remove ata_port*
With Tejun having added adev->ap some time ago we can get rid of the
almost unused port being passed to mode filters. And while we are
doing filters, lets turn on the !IORDY filter as well.
Signed-off-by: Alan Cox <alan@redhat.com>
With some hand massaging from Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Thu, 8 Mar 2007 23:09:12 +0000 (23:09 +0000)]
sata_sil: First step to removing ->post_set_mode
Now that we have ata_do_set_mode() available for drivers to use we don't
actually need ->post_set_mode() as the driver can wrap set_mode nicely
and do stuff before or after (eg PCMCIA needs before), so we can kill off
a method in all the structs
While I was at it I added kernel-doc to the function involved.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Thu, 8 Mar 2007 23:22:59 +0000 (23:22 +0000)]
libata-core: Fix the iordy methods
This alone isn't sufficient to save the universe from prehistoric disks
and controllers but it is a first important step. Split off a separate
function to provide a mode filter when controller iordy is not available.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan [Tue, 6 Mar 2007 10:37:52 +0000 (02:37 -0800)]
pata: expose set_mode method so it can be wrapped
This splits set_mode into do_set_mode and the wrapper so that a driver can
call the standard method inside its own. This in theory also obsoletes
->post_set_mode().
Signed-off-by: Alan Cox <alan@redhat.com> Cc: Jeff Garzik <jeff@garzik.org> Cc: Tejun Heo <htejun@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Thu, 8 Mar 2007 23:28:52 +0000 (23:28 +0000)]
pata_hpt37x: Updates from drivers/ide work
Drag pata_hpt37x kicking and screaming in the direction of
drivers/ide/pci/hpt366.c and all the work that Sergei has been doing
there. Plenty left to be done but this is a good snapshot for folks to
work on and to review
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Wed, 7 Mar 2007 16:54:24 +0000 (16:54 +0000)]
pata_sis: Clean up using cable_detect methods
This changeset revolves around the fact that all the SiS controllers have
the same enable bits, but differing cable detection methods. Previously
that meant each type had its own error_handler methods. Instead we can
now implement different ->cable_detect methods and share a single
error_handler which does the filtering by enable bits.
In addition we had some auto const arrays that should be static const. I'm
not sure if gcc already treats them intelligently but adding the static
will make sure.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Wed, 7 Mar 2007 16:48:09 +0000 (16:48 +0000)]
pata_marvell: Cable and reset fixes
There are two changes here. Firstly we switch to a cable detect method,
secondly the old code forgot to call ata_std_prereset() but somehow
managed to work anyway. Fix the missing call.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Morrison, Tom [Tue, 6 Mar 2007 10:38:10 +0000 (02:38 -0800)]
Support for Marvell 7042 Chip
Added Support for Marvell 7042 Chip - 7042 has same capabilities & behavior
as 6042.
Signed-off-by: Thomas A. Morrison <tmorrison@empirix.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Tue, 6 Mar 2007 10:37:56 +0000 (02:37 -0800)]
libata: cable detection fixes
2.6.21-rc has horrible problems with libata and PATA cable types (and
thus speeds). This occurs because Tejun fixed a pile of other bugs and
we now do cable detect enforcement for drive side detection properly.
Unfortunately we don't do the process around cable detection right. Tejun
identified the problem and pointed to the right Annex in the spec, this patch
implements the rest of the needed changes.
We add a ->cable_detect() method called after the identify
sequence which allows a host to do host side detection at this point
should it wish, or to modify the results of the drive side identify.
This separate ->cable_detect method also cleans up a lot of code because
many drivers have their own error_handler methods which really just set
the cable type.
If there is no ->cable_detect method the cable type is left alone so a
driver setting it earlier (eg because it has the SATA flags set or
because it uses the old error_handler approach) will still do the right
thing (or at least the same thing) as before.
This patch simply adds the cable_detect method and helpers it doesn't use
them but other follow up patches will (ie Adrian please don't submit
patches to unexport them ;))
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Robert Hancock [Tue, 6 Mar 2007 10:37:51 +0000 (02:37 -0800)]
libata: warn if speed limited due to 40-wire cable
Warn the user if a drive's transfer rate is limited because of a 40-wire
cable detection.
Signed-off-by: Robert Hancock <hancockr@shaw.ca> Cc: Jeff Garzik <jeff@garzik.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark Lord [Fri, 2 Feb 2007 17:36:25 +0000 (12:36 -0500)]
RESEND: libata: check cdb len per dev instead of per host
Resending, with s/printk/DPRINTK/ as pointed out by Alan.
Fix libata to perform CDB len validation per device
rather than per host. This way, validation still works
when we have a mix of 12-byte and 16-byte devices on
a common host interface.
Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan [Fri, 2 Mar 2007 00:56:15 +0000 (00:56 +0000)]
libata: dev_config does not need ap and adev passing
It used to be impossible to get from ata_device to ata_port but that is
no longer true. Various methods have been cleaned up over time but
dev_config still takes both and most users don't need both anyway. Tidy
this one up
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jeff Garzik [Mon, 26 Feb 2007 06:26:06 +0000 (01:26 -0500)]
[libata] sata_mv: clean up DMA boundary issues, turn on 64-bit DMA
The chips covered by sata_mv have a 32-bit DMA boundary they must not
cross, not a 64K boundary. We are merely limited to a 64K maximum
segment size. Therefore, the DMA scatter/gather table fill code can be
greatly simplified, and we need not cut in half the S/G table size as
reported to the SCSI layer.
Also, the driver forget to turn on 64-bit DMA at the PCI layer. All
other data structures (both hardware and software) have been prepped for
64-bit PCI DMA. It was simply never turned on. <fingers crossed> let's
see if it still works...
Neil Horman [Thu, 26 Apr 2007 17:47:36 +0000 (13:47 -0400)]
sis900: Allocate rx replacement buffer before rx operation
Just found a hole in my last patch. It was reported to me that shortly after we
integrated this patch. The report was of an oops that took place inside of
netif_rx when using the sis900 driver. Looking at my origional patch I noted
that there was a spot between the new skb_alloc and the refill_rx_ring label
where skb got reassigned to the pointer currently held in the rx_ring for the
purposes of receiveing the frame. The result of this is however that the buffer
that gets passed to netif_rx (if it is called), then gets placed right back into
the rx_ring. So if you receive frames fast enough the skb being processed by
the network stack can get corrupted. The reporter is testing out the fix I've
written for this below (I'm not near my hardware at the moment to test myself),
but I wanted to post it for review ASAP. I'll post test results when I hear
them, but I think this is a pretty straightforward fix. It just uses a separate
pointer to do the rx operation, so that we don't improperly reassign the pointer
that we use to refill the rx ring.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.infradead.org/mtd-2.6: (46 commits)
[MTD] [MAPS] drivers/mtd/maps/ck804xrom.c: convert pci_module_init()
[MTD] [NAND] CM-x270 MTD driver
[MTD] [NAND] Wrong calculation of page number in nand_block_bad()
[MTD] [MAPS] fix plat-ram printk format
[JFFS2] Fix compr_rubin.c build after include file elimination.
[JFFS2] Handle inodes with only a single metadata node with non-zero isize
[JFFS2] Tidy up licensing/copyright boilerplate.
[MTD] [OneNAND] Exit loop only when column start with 0
[MTD] [OneNAND] Fix access the past of the real oobfree array
[MTD] [OneNAND] Update Samsung OneNAND official URL
[JFFS2] Better fix for all-zero node headers
[JFFS2] Improve read_inode memory usage, v2.
[JFFS2] Improve failure mode if inode checking leaves unchecked space.
[JFFS2] Fix cross-endian build.
[MTD] Finish conversion mtd_blkdevs to use the kthread API
[JFFS2] Obsolete dirent nodes immediately on unlink, where possible.
Use menuconfig objects: MTD
[MTD] mtd_blkdevs: Convert to use the kthread API
[MTD] Fix fwh_lock locking
[JFFS2] Speed up mount for directly-mapped NOR flash
...
The simplification made in that change works with the assumption that
the 'offset' parameter to these functions is always positive or zero,
which is not true. It can be and often is negative in order to access
SKB header values in front of skb->data.
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (78 commits)
USB: update MAINAINERS and CREDITS for Freescale USB driver
USB: update gadget files for fsl_usb2_udc driver
USB: add Freescale high-speed USB SOC device controller driver
USB: quirk for broken suspend of IT8152F/G
USB: iowarrior.c: timeouts too small in usb_control_msg calls
USB: dell device id for option.c
USB: Remove Huawei unusual_devs entry
USB: CP2101 New Device IDs
USB: add picdem device to ldusb
usbfs micro optimitation
USB: remove ancient/broken CRIS hcd
usb ethernet gadget, workaround network stack API glitch
USB: add "busnum" attribute for USB devices
USB: cxacru: ADSL state management
usbatm: Detect usb device shutdown and ignore failed urbs
USB: Remove duplicate define of OHCI_QUIRK_ZFMICRO
USB: BandRich BandLuxe HSDPA Data Card Driver
USB gadget rndis: fix struct rndis_packet_msg_type unaligned bug
USB Elan FTDI: check for driver registration status
USB: sierra: add more checks on shutdown
...
Merge branch 'master' of ssh://master.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb
* 'master' of ssh://master.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (184 commits)
V4L/DVB (5563): Radio-maestro.c Replace radio_ioctl to use video_ioctl2
V4L/DVB (5562): Radio-gemtek-pci.c Replace gemtek_pci_ioctl to use video_ioctl2
V4L/DVB (5560): Ivtv: fix incorrect bitwise-and for command flags.
V4L/DVB (5558): Opera: use 7-bit i2c addresses
V4L/DVB (5557): Cafe_ccic: check return value of pci_enable_device
V4L/DVB (5556): Radio-gemtek.c Replace gemtek_ioctl to use video_ioctl2
V4L/DVB (5555): Radio-aimslab.c Replace rt_ioctl to use video_ioctl2
V4L/DVB (5554): Fix: vidioc_g_parm were not zeroing the memory
V4L/DVB (5553): Replace typhoon_do_ioctl to use video_ioctl2
V4L/DVB (5552): Plan-b: Switch to refcounting PCI API
V4L/DVB (5551): Plan-b: header change
V4L/DVB (5550): Radio-sf16fmi.c Replace fmi_do_ioctl to use video_ioctl2
V4L/DVB (5549): Radio-sf16fmr2.c Replace fmr2_do_ioctl to use video_ioctl2
V4L/DVB (5548): Fix v4l2 buffer to the length
V4L/DVB (5547): Add ENUM_FRAMESIZES and ENUM_FRAMEINTERVALS ioctls
V4L/DVB (5546): Radio-terratec.c Replace tt_do_ioctl to use video_ioctl2
V4L/DVB (5545): Saa7146: Release capture buffers on device close
V4L/DVB (5544): Budget-av: Make inversion setting configurable, add KNC ONE V1.0 card
V4L/DVB (5543): Tda10023: Add support for frontend TDA10023
V4L/DVB (5542): Budget-av: Remove polarity switching of the clock for DVB-C
...
Li Yang [Mon, 23 Apr 2007 17:38:18 +0000 (10:38 -0700)]
USB: update MAINAINERS and CREDITS for Freescale USB driver
Add MAINAINERS and CREDITS entry for Freescale Highspeed USB device
driver.
Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Li Yang [Mon, 23 Apr 2007 17:37:36 +0000 (10:37 -0700)]
USB: update gadget files for fsl_usb2_udc driver
Update gadget_chip.c, ether.c for newly added Freescale Highspeed USB
device driver.
Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Li Yang [Mon, 23 Apr 2007 17:54:25 +0000 (10:54 -0700)]
USB: add Freescale high-speed USB SOC device controller driver
Freescale high-speed USB SOC can be found on some Freescale processors
among different architectures. It supports both host and device functions.
This driver adds its device support for Linux USB Gadget layer.
It is tested on MPC8349 and MPC8313, but should work on other platforms
with minor tweaks. The driver passed USBCV 1.3 compliance tests. Note
that this driver doesn't yet include OTG support.
Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Jiang Bo <tanya.jiang@freescale.com> Signed-off-by: Bruce Schmid <duck@freescale.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: iowarrior.c: timeouts too small in usb_control_msg calls
The driver uses usb_control_msg() for exchanging data with the device.
When the driver lived freeley _outside_ the kernel tree (pre 2.6.21) the
timeouts for these calls where set to 5*HZ for reading, 1HZ for writing.
(These timeouts seemed to work fine for all users of the driver, at
least nobody complained in the last 2 years.
The current code (2.6.21-rc5) removed the 'HZ' from the timeouts and
left the driver with 5 jiffies for reading and 1 jiffy for writing. My
new machine is fast, but not that fast.
The patch also removes a useless debug statement, which was left over
from testing a broken firmware version
Phil Dibowitz [Mon, 16 Apr 2007 06:42:40 +0000 (23:42 -0700)]
USB: Remove Huawei unusual_devs entry
Per the Rui Santos and the hardware manufacturers, this actually inhibits
useful parts of the hardware. The correct way to use this hardware is with the
software at http://www.kanoistika.sk/bobovsky/archiv/umts/ and the manufacturers
are also planning on including Linux drivers/material in future revisions.
I have found that /drivers/usb/misc/ldusb.c works with the "PICDEM Full
Speed USB"
http://www.microchip.com/stellent/idcplg?IdcService=SS_GET_PAGE&nodeId=1406&dDocName=en021940
Signed-off-by: Joey S Goncalves <jgoncalves@peragrin.com> Cc: Michael Hund <MHund@LD-Didactic.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Sun, 22 Apr 2007 18:05:52 +0000 (11:05 -0700)]
USB: remove ancient/broken CRIS hcd
Remove the old crisv10 HCD ... it can't have built for some time,
doesn't even have a Kconfig entry, was the last driver not to have
been converted to the "hcd" framework, and considering the usbcore
changes since its last patch was merged, has just got to buggy as
all get-out.
I'm told Axis has a new driver, and will be submitting it soon.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Mikael Starvik <mikael.starvik@axis.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Erik Hovland [Mon, 23 Apr 2007 17:50:15 +0000 (10:50 -0700)]
usb ethernet gadget, workaround network stack API glitch
Another workaround for the glitch in the network layer, whereby one call
ignores the (otherwise kernel-wide) convention that free() calls should
not oops when passed nulls. This code already handles that API glitch in
most other paths.
From: Erik Hovland <erik@hovland.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Simon Arlott [Thu, 26 Apr 2007 07:38:05 +0000 (00:38 -0700)]
USB: cxacru: ADSL state management
The device has commands to start/stop the ADSL function, so this adds a
sysfs attribute to allow it to be started/stopped/restarted. It also stops
polling the device for status when the ADSL function is disabled.
There are no problems with sending multiple start or stop commands, even
with a fast loop of them the device still works. There is no need to
protect the restart process from further user actions while it's waiting
for 1.5s.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Cc: Duncan Sands <duncan.sands@math.u-psud.fr> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Simon Arlott [Thu, 26 Apr 2007 07:38:04 +0000 (00:38 -0700)]
usbatm: Detect usb device shutdown and ignore failed urbs
Detect usb device shutdown and ignore failed urbs. This happens when the
driver is unloaded or the device is unplugged.
I'm not sure what other urb statuses should be ignored, and the warning
message doesn't need to be shown when the module is unloaded or the device
is removed.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Cc: Duncan Sands <duncan.sands@math.u-psud.fr> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Leon Leong [Thu, 26 Apr 2007 07:38:02 +0000 (00:38 -0700)]
USB: BandRich BandLuxe HSDPA Data Card Driver
Add the detection for the BandRich BandLuxe C100/C100S/C120 HSDPA Data
Card. With the vendor and product IDs are set properly, the data card can
be detected and works fine.
Signed-off-by: Leon Leong <upleong@bandrich.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Tue, 17 Apr 2007 20:06:29 +0000 (13:06 -0700)]
USB: add an ohci board-specific quirk
Use the new ohci-pci quirk infrastructure to address the problem it was
created to address: a quirk specific to the Portege 4000, in buzilla as
http://bugzilla.kernel.org/show_bug.cgi?id=6723
Also fix a misuse of "__devinit" for the quirk functions. It must not
be used without first ensuring that the references from the quirk tables
are gone, and that the function using those quirk tables is also gone.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Tue, 17 Apr 2007 23:10:10 +0000 (16:10 -0700)]
USB: usbnet reports minidriver name through ethtool
Update "usbnet" so that ethtool reports the name of the minidriver in use
(e.g. asix, cdc_ether, dm9601, rndis_host) instead of "usbnet". This is a
better match to how other network drivers work, resolving a minor open issue.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 18 Apr 2007 00:53:20 +0000 (17:53 -0700)]
USB: rndis_host, various cleanups
Cleanups to the rndis_host code, and a tweak that helps talking to
PXA hardware. Mostly from Ole André Vadla Ravnås <oleavr@gmail.com>
- Prevent SET_INTERFACE requests, they give PXA hardware bad indigestion
- For paranoia, null a pointer after freeing its data
- Wrap up ActiveSync oddities for RNDIS_QUERY in one routine
- Use that wrapper when getting the Ethernet address
- Whitespace fixes
Plus add a comment noting the open issues about some RNDIS clients still
needing TBD kinds of browbeating to accept non-jumbogram packets.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Wed, 11 Apr 2007 20:47:26 +0000 (13:47 -0700)]
usbmon: bus zero
Add the "bus zero" feature to the usbmon. If a user process specifies bus
with number zero, it receives events from all buses. This is useful when
we wish to see initial enumeration when a bus is created, typically after
a modprobe. Until now, an application had to loop until a new bus could
be open, then start capturing on it. This procedure was cumbersome and
could lose initial events. Also, often it's too bothersome to find exactly
to which bus a specific device is attached.
Paolo Albeni provided the original concept implementation. I added the
handling of "bus->monitored" flag and generally fixed it up.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tony Lindgren [Sun, 1 Apr 2007 01:15:43 +0000 (18:15 -0700)]
USB: Allow transfer_buffer with transfer_dma
Some host controller drivers may need a PIO fallback when a DMA channel
is temporarily unavailable. This patch provides an address that such
drivers can use for PIO in those cases, and nulls that field out when
no such address is available (highmem) which should help usbmon.
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / linux-beck.git / log