Yinghai Lu [Sat, 16 Feb 2013 18:58:34 +0000 (11:58 -0700)]
PCI/ACPI: Don't cache _PRT, and don't associate them with bus numbers
Previously, we cached _PRT (PCI routing table, ACPI 5.0 sec 6.2.12)
contents and associated each _PRT entry with a PCI bus number. The bus
number association means dependencies on PCI device enumeration and bus
number assignment, as well as on the PCI/ACPI binding process.
After 4f535093cf ("PCI: Put pci_dev in device tree as early as possible"),
these dependencies caused the IRQ issues reported by Peter:
pci 0000:00:1e.0: PCI bridge to [bus 09] (subtractive decode)
pci 0000:00:1e.0: can't derive routing for PCI INT A
snd_ctxfi 0000:09:02.0: PCI INT A: no GSI - using ISA IRQ 5
irq 18: nobody cared (try booting with the "irqpoll" option)
This patch removes _PRT caching. Instead, we evaluate _PRT as needed
in the pci_enable_device() path. This also removes the dependency on
PCI bus numbers: we can simply look at the _PRT associated with each
bridge as we walk upstream toward the root.
[bhelgaas: changelog]
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=53561 Reported-and-tested-by: Peter Hurley <peter@hurleysoftware.com> Suggested-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Jiang Liu [Wed, 30 Jan 2013 16:10:10 +0000 (00:10 +0800)]
PCI: acpiphp: Remove dead code for PCI host bridge hotplug
Commit 668192b678201d2fff27c "PCI: acpiphp: Move host bridge hotplug
to pci_root.c" has moved PCI host bridge hotplug logic from acpiphp
to pci_root, but there is still PCI host bridge hotplug related
dead code left in acpiphp. So remove those dead code.
Now companion ACPI devices are always created before corresponding
PCI devices. And the ACPI event handle_hotplug_event_bridge() will be
installed only if it has associated PCI device. So remove dead code to
handle bridge hot-adding in function handle_hotplug_event_bridge().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Jiang Liu [Wed, 30 Jan 2013 16:10:09 +0000 (00:10 +0800)]
PCI: acpiphp: Create companion ACPI devices before creating PCI devices
With commit 4f535093cf8f6da8c "PCI: Put pci_dev in device tree as
early as possible", companion ACPI devices should be created before
creating corresponding PCI devices, otherwise it will break the ACPI
PCI binding logic.
Without this patch, the /sys/bus/pci/devices/.../firmware_node symlink
is missing after hot-removing and hot-adding a device with acpiphp.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Yinghai Lu [Mon, 21 Jan 2013 21:20:52 +0000 (13:20 -0800)]
PCI: Put pci_dev in device tree as early as possible
We want to put pci_dev structs in the device tree as soon as possible so
for_each_pci_dev() iteration will not miss them, but driver attachment
needs to be delayed until after pci_assign_unassigned_resources() to make
sure all devices have resources assigned first.
This patch moves device registering from pci_bus_add_devices() to
pci_device_add(), which happens earlier, leaving driver attachment in
pci_bus_add_devices().
It also removes unattached child bus handling in pci_bus_add_devices().
That's not needed because child bus via pci_add_new_bus() is already
in parent bus children list.
[bhelgaas: changelog] Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Yinghai Lu [Mon, 21 Jan 2013 21:20:51 +0000 (13:20 -0800)]
PCI: Skip attaching driver in device_add()
We want to add PCI devices to the device tree as early as possible but
delay attaching drivers.
device_add() adds a device to the device hierarchy and (via
device_attach()) attaches a matching driver and calls its .probe() method.
We want to separate adding the device to the hierarchy from attaching the
driver.
This patch does that by adding "match_driver" in struct pci_dev. When
false, we return failure from pci_bus_match(), which makes device_attach()
believe there's no matching driver.
Later, we set "match_driver = true" and call device_attach() again, which
now attaches the driver and calls its .probe() method.
[bhelgaas: changelog, explicitly init dev->match_driver,
fold device_attach() call into pci_bus_add_device()] Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Yinghai Lu [Mon, 21 Jan 2013 21:20:50 +0000 (13:20 -0800)]
PCI: acpiphp: Keep driver loaded even if no slots found
Could have root bus hot-added later and there may be slots that need
acpiphp.
The result returned by acpiphp_get_num_slots() is meaningless, because
the bridge the slots are under may be added after this function has been
called, so drop acpiphp_get_num_slots() and the code using it.
Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Yinghai Lu [Mon, 21 Jan 2013 21:20:47 +0000 (13:20 -0800)]
PCI/ACPI: acpiphp: Rename alloc_acpiphp_hp_work() to alloc_acpi_hp_work()
Will need to use it for PCI root bridge hotplug support, so rename
*acpiphp* to *acpi* and move to osc.c. Also make kacpi_hotplug_wq static
after that.
Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> CC: Len Brown <lenb@kernel.org> CC: linux-acpi@vger.kernel.org
Jiang Liu [Mon, 21 Jan 2013 21:20:46 +0000 (13:20 -0800)]
PCI: Make device create/destroy logic symmetric
According to device model documentation, the way to create/destroy PCI
devices should be symmetric. The rule is to either use
1) device_register()/device_unregister()
or
2) device_initialize()/device_add()/device_del()/put_device().
So change PCI core logic to follow the rule and get rid of the redundant
pci_dev_get()/pci_dev_put() pair.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Jiang Liu [Mon, 21 Jan 2013 21:20:45 +0000 (13:20 -0800)]
PCI: Fix reference count leak in pci_dev_present()
Function pci_get_dev_by_id() takes a reference on the pci_dev returned, so
pci_dev_present() should release the corresponding reference.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Yinghai Lu [Mon, 21 Jan 2013 21:20:44 +0000 (13:20 -0800)]
PCI: Set pci_dev dev_node early so IOAPIC irq_descs are allocated locally
Otherwise irq_desc for PCI bridge with hot-added IOAPIC may not be
allocated on the local node.
Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Yinghai Lu [Mon, 21 Jan 2013 21:20:43 +0000 (13:20 -0800)]
PCI: Add root bus children dev's res to fail list
We can stop trying according to try_number now and do not need to use
root_bus checking as stop sign.
In extreme case we could need to reallocate resource for device just
under root bus. For PCI root bus hot-add, we need to retry to assign
resources to PCI devices just under pci root bus.
Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Yinghai Lu [Mon, 21 Jan 2013 21:20:42 +0000 (13:20 -0800)]
PCI: acpiphp: Add is_hotplug_bridge detection
When system support hotplug bridge with children hotplug slots, we need
to make sure that parent bridge get preallocated resource so later when
device is plugged into children slot, those children devices will get
resource allocated.
We do not meet this problem, because for PCIe hotplug card, when acpiphp
is used, pci_scan_bridge will set that for us when detect hotplug bit in
slot cap.
Reported-and-tested-by: Jason Baron <jbaron@redhat.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Jason Baron <jbaron@redhat.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Bjorn Helgaas [Fri, 25 Jan 2013 18:26:36 +0000 (11:26 -0700)]
Merge branch 'acpi-scan' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm into pci/acpi-scan2
* 'acpi-scan' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / scan: Drop acpi_bus_add() and use acpi_bus_scan() instead
ACPI: update ej_event interface to take acpi_device
ACPI / scan: Add second pass to acpi_bus_trim()
ACPI / scan: Change the implementation of acpi_bus_trim()
ACPI / scan: Drop the second argument of acpi_bus_trim()
ACPI / scan: Drop the second argument of acpi_device_unregister()
ACPI: Remove the ops field from struct acpi_device
ACPI: remove unused acpi_op_bind and acpi_op_unbind
ACPI / scan: Fix check of device_attach() return value.
ACPI / scan: Drop acpi_bus_add() and use acpi_bus_scan() instead
The only difference between acpi_bus_scan() and acpi_bus_add() is the
invocation of acpi_update_all_gpes() in the latter which in fact is
unnecessary, because acpi_update_all_gpes() has already been called
by acpi_scan_init() and the way it is implemented guarantees the next
invocations of it to do nothing.
For this reason, drop acpi_bus_add() and make all its callers use
acpi_bus_scan() directly instead of it. Additionally, rearrange the
code in acpi_scan_init() slightly to improve the visibility of the
acpi_update_all_gpes() call in there.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Yinghai Lu <yinghai@kernel.org>
Make acpi_bus_trim() work in analogy with acpi_bus_scan() and carry
out two passes such that ACPI drivers will be detached from device
nodes being removed in the first pass and the device nodes themselves
will be removed in the second pass.
For this purpose split the driver unregistration out of
acpi_bus_remove() into a new routine, acpi_bus_device_detach(), that
will be executed by acpi_bus_trim() in the additional first pass as
a post-order callback.
This is necessary, because some ACPI drivers' .remove() routines
unregister struct device objects associated with the ACPI device
nodes being removed and that needs to happen while the ACPI
device nodes are still around (for example, in case they need to be
used for power management or similar things at that time).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Toshi Kani <toshi.kani@hp.com> Acked-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
ACPI / scan: Change the implementation of acpi_bus_trim()
The current acpi_bus_trim() implementation is not really
straightforward and may be simplified significantly by using
acpi_walk_namespace() with acpi_bus_remove() as a post-order
callback.
Observe that acpi_bus_remove(), as called by acpi_bus_trim(), cannot
actually fail, because its first argument is guaranteed not to be
NULL thanks to the acpi_bus_get_device() check in acpi_bus_trim(),
so simply move the acpi_bus_get_device() check to acpi_bus_remove()
and use acpi_walk_namespace() to execute it for every device under
start->handle as a post-order callback. The, run it directly for
start->handle itself.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Toshi Kani <toshi.kani@hp.com> Acked-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
ACPI / scan: Drop the second argument of acpi_bus_trim()
All callers of acpi_bus_trim() pass 1 (true) as the second argument
of it, so remove that argument entirely and change acpi_bus_trim()
to always behave as though it were 1.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Toshi Kani <toshi.kani@hp.com> Acked-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Jiang Liu [Mon, 14 Jan 2013 12:55:41 +0000 (13:55 +0100)]
ACPI: remove unused acpi_op_bind and acpi_op_unbind
With commit f2a33cde55a03 "ACPI: Drop ACPI device .bind() and .unbind()
callbacks", acpi_op_bind and acpi_op_unbind are not used any more. So
remove them.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Mika Westerberg [Fri, 11 Jan 2013 21:08:09 +0000 (22:08 +0100)]
ACPI / scan: Fix check of device_attach() return value.
Since device_attach() returns 1 on success (a driver has been bound
to the device), the check against its return value in
acpi_bus_device_attach() should modified to take that into accout.
Make it so.
[rjw: Subject and changelog.] Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Bjorn Helgaas [Thu, 10 Jan 2013 18:18:41 +0000 (11:18 -0700)]
Merge branch 'acpi-scan' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm into pci/yinghai-survey-resources+acpi-scan
* 'acpi-scan' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / scan: Treat power resources in a special way
ACPI: Remove unused struct acpi_pci_root.id member
ACPI: Drop ACPI device .bind() and .unbind() callbacks
ACPI / PCI: Move the _PRT setup and cleanup code to pci-acpi.c
ACPI / PCI: Rework the setup and cleanup of device wakeup
ACPI: Add .setup() and .cleanup() callbacks to struct acpi_bus_type
ACPI: Make acpi_bus_scan() and acpi_bus_add() take only one argument
ACPI: Replace ACPI device add_type field with a match_driver flag
ACPI: Drop the second argument of acpi_bus_scan()
ACPI: Remove the arguments of acpi_bus_add() that are not used
ACPI: Remove acpi_start_single_object() and acpi_bus_start()
ACPI / PCI: Fold acpi_pci_root_start() into acpi_pci_root_add()
ACPI: Change the ordering of acpi_bus_check_add()
ACPI: Replace struct acpi_bus_ops with enum type
ACPI: Reduce the usage of struct acpi_bus_ops
ACPI: Make acpi_bus_add() and acpi_bus_start() visibly different
ACPI: Change the ordering of PCI root bridge driver registrarion
ACPI: Separate adding ACPI device objects from probing ACPI drivers
Yinghai Lu [Sun, 4 Nov 2012 04:39:30 +0000 (21:39 -0700)]
x86/PCI: Implement pcibios_resource_survey_bus()
During testing remove/rescan root bus 00, found
[ 338.142574] bus: 'pci': really_probe: probing driver ata_piix with device 0000:00:01.1
[ 338.146788] ata_piix 0000:00:01.1: device not available (can't reserve [io 0x01f0-0x01f7])
[ 338.150565] ata_piix: probe of 0000:00:01.1 failed with error -22
because that fixed resource is not claimed.
For bootint path it is claimed in from
arch/x86/pci/i386.c::pcibios_allocate_resources()
Claim those resources, so on the remove/rescan will still use old
resources.
It is some kind honoring FW setting in the registers during hot add.
esp root-bus hot add is through acpi, BIOS has chance to set some registers
before handing over.
[bhelgaas: move weak definition to patch that uses it] Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Yinghai Lu [Sun, 4 Nov 2012 04:39:27 +0000 (21:39 -0700)]
x86/PCI: Factor out pcibios_allocate_dev_rom_resource()
Factor pcibios_allocate_rom_resources() and
pcibios_allocate_dev_rom_resource() out of pcibios_assign_resources().
This will allow us to allocate ROM resources for hot-added root buses.
[bhelgaas: changelog] Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Yinghai Lu [Sun, 4 Nov 2012 04:39:26 +0000 (21:39 -0700)]
x86/PCI: Allocate resources on a per-bus basis for hot-adding root buses
Previously pcibios_allocate_resources() allocated resources at boot-time
for all PCI devices using for_each_pci_dev(). This patch changes
pcibios_allocate_resources() so we can specify a bus, so we can do
similar allocation when hot-adding a root bus.
[bhelgaas: changelog] Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Yinghai Lu [Sun, 4 Nov 2012 04:39:25 +0000 (21:39 -0700)]
x86/PCI: Factor out pcibios_allocate_dev_resources()
Factor pcibios_allocate_dev_resources() out of
pcibios_allocate_resources(). Currently we only allocate these
resources at boot-time with a for_each_pci_dev() loop. Eventually
we'll use pcibios_allocate_dev_resources() for hot-added devices, too.
[bhelgaas: changelog] Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ACPI / scan: Treat power resources in a special way
Commit 805d410 (ACPI: Separate adding ACPI device objects from
probing ACPI drivers) introduced an ACPI power resources management
regression, because it didn't ensure that the power resources
driver bind to the struct acpi_device objects corresponding
to power resources as soon as they were created. As a result,
ACPI power management routines may attempt to access power resource
objects before they are ready to use.
To fix this problem, tell the acpi_add_single_object() in
acpi_bus_check_add() to probe the driver for objects of type
ACPI_BUS_TYPE_POWER. This fix has been verified to work on
HP nx6325 where the problem was first observed.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Toshi Kani <toshi.kani@hp.com>
ACPI: Drop ACPI device .bind() and .unbind() callbacks
Drop the .bind() and .unbind() that have no more users from
struct acpi_device_ops and remove all of the code referring to
them from drivers/acpi/scan.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Toshi Kani <toshi.kani@hp.com>
ACPI / PCI: Move the _PRT setup and cleanup code to pci-acpi.c
Move the code related to _PRT setup and removal and to power
resources from acpi_pci_bind() and acpi_pci_unbind() to the .setup()
and .cleanup() callbacks in acpi_pci_bus and remove acpi_pci_bind()
and acpi_pci_unbind() that have no purpose any more. Accordingly,
remove the code related to device .bind() and .unbind() operations
from the ACPI PCI root bridge driver.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Toshi Kani <toshi.kani@hp.com>
ACPI / PCI: Rework the setup and cleanup of device wakeup
Currently, the ACPI wakeup capability of PCI devices is set up
in two different places, partially in acpi_pci_bind() where
runtime wakeup is initialized and partially in
platform_pci_wakeup_init(), where system wakeup is initialized.
The cleanup is only done in acpi_pci_unbind() and it only covers
runtime wakeup.
Use the new .setup() and .cleanup() callbacks in struct acpi_bus_type
to consolidate that code and do the setup and the cleanup each in one
place.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Toshi Kani <toshi.kani@hp.com>
ACPI: Add .setup() and .cleanup() callbacks to struct acpi_bus_type
Add two new callbacks,.setup() and .cleanup(), struct acpi_bus_type
and modify acpi_platform_notify() to call .setup() after executing
acpi_bind_one() successfully and acpi_platform_notify_remove() to
call .cleanup() before running acpi_unbind_one(). This will allow
the users of struct acpi_bus_type, PCI in particular, to specify
operations to be executed right after the given device has been
associated with a companion struct acpi_device and right before
it's going to be detached from that companion, respectively.
The main motivation is to be able to get rid of acpi_pci_bind()
and acpi_pci_unbind(), which are horrible horrible stuff. [In short,
there are three problems with them: The way they populate the .bind()
and .unbind() callbacks of ACPI devices is rather less than
straightforward, they require special hotplug-specific paths to be
present in the ACPI namespace scanning code and by the time
acpi_pci_unbind() is called the PCI device object in question may
not exist any more.]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Toshi Kani <toshi.kani@hp.com>
ACPI: Make acpi_bus_scan() and acpi_bus_add() take only one argument
The callers of acpi_bus_add() usually assume that if it has
succeeded, then a struct acpi_device object has been attached to
the handle passed as the first argument. Unfortunately, however,
this assumption is wrong, because acpi_bus_scan(), and acpi_bus_add()
too as a result, may return a pointer to a different struct
acpi_device object on success (it may be an object corresponding to
one of the descendant ACPI nodes in the namespace scope below that
handle).
For this reason, the callers of acpi_bus_add() who care about
whether or not a struct acpi_device object has been created for
its first argument need to check that using acpi_bus_get_device()
anyway, so the second argument of acpi_bus_add() is not really
useful for them. The same observation applies to acpi_bus_scan()
executed directly from acpi_scan_init().
Therefore modify the relevant callers of acpi_bus_add() to check the
existence of the struct acpi_device in question with the help of
acpi_bus_get_device() and drop the no longer necessary second
argument of acpi_bus_add(). Accordingly, modify acpi_scan_init() to
use acpi_bus_get_device() to get acpi_root and drop the no longer
needed second argument of acpi_bus_scan().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Toshi Kani <toshi.kani@hp.com>
ACPI: Replace ACPI device add_type field with a match_driver flag
After the removal of the second argument of acpi_bus_scan() there is
no difference between the ACPI_BUS_ADD_MATCH and ACPI_BUS_ADD_START
add types, so the add_type field in struct acpi_device may be
replaced with a single flag. Do that calling the flag match_driver.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Toshi Kani <toshi.kani@hp.com>
After the removal of acpi_start_single_object() and acpi_bus_start()
the second argument of acpi_bus_scan() is not necessary any more,
so drop it and update acpi_bus_check_add() accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Toshi Kani <toshi.kani@hp.com>
ACPI: Remove the arguments of acpi_bus_add() that are not used
Notice that acpi_bus_add() uses only 2 of its 4 arguments and
redefine its header to match the body. Update all of its callers as
necessary and observe that this leads to quite a number of removed
lines of code (Linus will like that).
Add a kerneldoc comment documenting acpi_bus_add() and wonder how
its callers make wrong assumptions about the second argument (make
note to self to take care of that later).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Toshi Kani <toshi.kani@hp.com>
ACPI: Remove acpi_start_single_object() and acpi_bus_start()
The ACPI PCI root bridge driver was the only ACPI driver implementing
the .start() callback, which isn't used by any ACPI drivers any more
now.
For this reason, acpi_start_single_object() has no purpose any more,
so remove it and all references to it. Also remove
acpi_bus_start_device(), whose only purpose was to call
acpi_start_single_object().
Moreover, since after the removal of acpi_bus_start_device() the
only purpose of acpi_bus_start() remains to call
acpi_update_all_gpes(), move that into acpi_bus_add() and drop
acpi_bus_start() too, remove its header from acpi_bus.h and
update all of its former users accordingly.
This change was previously proposed in a different from by
Yinghai Lu.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Toshi Kani <toshi.kani@hp.com>
ACPI / PCI: Fold acpi_pci_root_start() into acpi_pci_root_add()
Move the code from the ACPI PCI root bridge's .start() callback
routine, acpi_pci_root_start(), directly into acpi_pci_root_add()
and drop acpi_pci_root_start().
It is safe to do that, because it is now always guaranteed that
when struct pci_dev objects are created, their companion struct
acpi_device objects are already present, so it is not necessary to
wait for them to be created before calling pci_bus_add_devices().
This change was previously proposed in a different form by
Yinghai Lu.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Toshi Kani <toshi.kani@hp.com>
If acpi_bus_check_add() is called for a handle already having an
existing struct acpi_device object attached, it is not necessary to
check the type and status of the device correspondig to it, so
change the ordering of acpi_bus_check_add() to avoid that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Toshi Kani <toshi.kani@hp.com>
Notice that one member of struct acpi_bus_ops, acpi_op_add, is not
used anywhere any more and the relationship between its remaining
members, acpi_op_match and acpi_op_start, is such that it doesn't
make sense to set the latter without setting the former at the same
time. Therefore, replace struct acpi_bus_ops with new a enum type,
enum acpi_bus_add_type, with three values, ACPI_BUS_ADD_BASIC,
ACPI_BUS_ADD_MATCH, ACPI_BUS_ADD_START, corresponding to
both acpi_op_match and acpi_op_start unset, acpi_op_match set and
acpi_op_start unset, and both acpi_op_match and acpi_op_start set,
respectively.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Toshi Kani <toshi.kani@hp.com>
Objects of type struct acpi_bus_ops are currently used to pass
information between different parts of the ACPI namespace scanning
code, sometimes in quite convoluted ways. It turns out that that
is not necessary in some cases, so simplify the code by reducing
the utilization of struct acpi_bus_ops objects where clearly
possible.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Toshi Kani <toshi.kani@hp.com>
ACPI: Make acpi_bus_add() and acpi_bus_start() visibly different
The current ACPI namespace scanning code suggests that acpi_bus_add()
and acpi_bus_start() share some code. In fact, however, they are
completely different code paths (except for the initial checks), so
refactor the code to make that distinction visibly clear.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Toshi Kani <toshi.kani@hp.com>
ACPI: Change the ordering of PCI root bridge driver registrarion
Instead of running acpi_pci_root_init() from a separate subsys
initcall, call it directly from acpi_scan_init() before scanning the
ACPI namespace for the first time, so that the PCI root bridge
driver's .add() routine, acpi_pci_root_start(), is always run
before binding ACPI drivers or attaching "companion" device objects
to struct acpi_device objects below the root bridge's device node in
the ACPI namespace.
The first, simpler reason for doing this is that it makes the
situation during boot more similar to the situation during hotplug,
in which the ACPI PCI root bridge driver is always present.
The second reason is that acpi_pci_root_init() causes struct pci_dev
objects to be created for all PCI devices below the bridge and
these objects may be necessary for whatever is done with the other
ACPI device nodes in that namespace scope. For example, devices
created by acpi_create_platform_device() sometimes may need to be
added to the device hierarchy as children of PCI bridges. For this
purpose, however, the struct pci_dev objects representing those
bridges need to exist before the platform devices in question are
registered.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Toshi Kani <toshi.kani@hp.com>
ACPI: Separate adding ACPI device objects from probing ACPI drivers
Split the ACPI namespace scanning for devices into two passes, such
that struct acpi_device objects are registerd in the first pass
without probing ACPI drivers and the drivers are probed against them
directly in the second pass.
There are two main reasons for doing that.
First, the ACPI PCI root bridge driver's .add() routine,
acpi_pci_root_add(), causes struct pci_dev objects to be created for
all PCI devices under the given root bridge. Usually, there are
corresponding ACPI device nodes in the ACPI namespace for some of
those devices and therefore there should be "companion" struct
acpi_device objects to attach those struct pci_dev objects to. These
struct acpi_device objects should exist when the corresponding
struct pci_dev objects are created, but that is only guaranteed
during boot and not during hotplug. This leads to a number of
functional differences between the boot and the hotplug cases which
are not strictly necessary and make the code more complicated.
For example, this forces the ACPI PCI root bridge driver to defer the
registration of the just created struct pci_dev objects and to use a
special .start() callback routine, acpi_pci_root_start(), to make
sure that all of the "companion" struct acpi_device objects will be
present at PCI devices registration time during hotplug.
If those differences can be eliminated, we will be able to
consolidate the boot and hotplug code paths for the enumeration and
registration of PCI devices and to reduce the complexity of that
code quite a bit.
The second reason is that, in general, it should be possible to
resolve conflicts of resources assigned by the BIOS to different
devices represented by ACPI namespace nodes before any drivers bind
to them and before they are attached to "companion" objects
representing physical devices (such as struct pci_dev). However, for
this purpose we first need to enumerate all ACPI device nodes in the
given namespace scope.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Toshi Kani <toshi.kani@hp.com>
leds: leds-gpio: set devm_gpio_request_one() flags param correctly
commit a99d76f leds: leds-gpio: use gpio_request_one
changed the leds-gpio driver to use gpio_request_one() instead
of gpio_request() + gpio_direction_output()
Unfortunately, it also made a semantic change that breaks the
leds-gpio driver.
The gpio_request_one() flags parameter was set to:
GPIOF_DIR_OUT | (led_dat->active_low ^ state)
Since GPIOF_DIR_OUT is 0, the final flags value will just be the
XOR'ed value of led_dat->active_low and state.
This value were used to distinguish between HIGH/LOW output initial
level and call gpio_direction_output() accordingly.
With this new semantic gpio_request_one() will take the flags value
of 1 as a configuration of input direction (GPIOF_DIR_IN) and will
call gpio_direction_input() instead of gpio_direction_output().
Linus Torvalds [Thu, 3 Jan 2013 01:46:14 +0000 (17:46 -0800)]
Merge git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
"This fixes some small errors in the new da9055 driver, eliminates a
compiler warning and adds DT support for the twl4030_wdt driver (so
that we can have multiple watchdogs with DT on the omap platforms)."
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: twl4030_wdt: add DT support
watchdog: omap_wdt: eliminate unused variable and a compiler warning
watchdog: da9055: Don't update wdt_dev->timeout in da9055_wdt_set_timeout error path
watchdog: da9055: Fix invalid free of devm_ allocated data
Linus Torvalds [Thu, 3 Jan 2013 01:44:29 +0000 (17:44 -0800)]
Merge tag '3.8-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Some fixes for v3.8. They include a fix for the new SR-IOV sysfs
management support, an expanded quirk for Ricoh SD card readers, a
Stratus DMI quirk fix, and a PME polling fix."
* tag '3.8-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Reduce Ricoh 0xe822 SD card reader base clock frequency to 50MHz
PCI/PM: Do not suspend port if any subordinate device needs PME polling
PCI: Add PCIe Link Capability link speed and width names
PCI: Work around Stratus ftServer broken PCIe hierarchy (fix DMI check)
PCI: Remove spurious error for sriov_numvfs store and simplify flow
David Howells [Wed, 2 Jan 2013 15:13:02 +0000 (15:13 +0000)]
UAPI: Strip _UAPI prefix on header install no matter the whitespace
Commit 56c176c9cac9 ("UAPI: strip the _UAPI prefix from header guards
during header installation") strips the _UAPI prefix from header guards,
but only if there's a single space between the cpp directive and the
label.
Make it more flexible and able to handle tabs and multiple white space
characters.
Signed-off-by: David Howells <dhowell@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 3 Jan 2013 01:33:50 +0000 (17:33 -0800)]
Merge tag 'ecryptfs-3.8-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull ecryptfs fixes from Tyler Hicks:
"Two self-explanatory fixes and a third patch which improves
performance: when overwriting a full page in the eCryptfs page cache,
skip reading in and decrypting the corresponding lower page."
* tag 'ecryptfs-3.8-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
fs/ecryptfs/crypto.c: make ecryptfs_encode_for_filename() static
eCryptfs: fix to use list_for_each_entry_safe() when delete items
eCryptfs: Avoid unnecessary disk read and data decryption during writing
Linus Torvalds [Thu, 3 Jan 2013 01:32:49 +0000 (17:32 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fixes from Sage Weil:
"Two of Alex's patches deal with a race when reseting server
connections for open RBD images, one demotes some non-fatal BUGs to
WARNs, and my patch fixes a protocol feature bit failure path."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: fix protocol feature mismatch failure path
libceph: WARN, don't BUG on unexpected connection states
libceph: always reset osds when kicking
libceph: move linger requests sooner in kick_requests()
It's very unlikely this will happen as shared pages are not marked
pte_numa -- see the page_mapcount() check in change_pte_range() -- but
it is possible.
To address this, this patch restores sp->lock as originally implemented
by Kosaki Motohiro. In the path where get_vma_policy() is called, it
should not be calling sp_alloc() so it is not necessary to treat the PTL
specially.
Linus Torvalds [Wed, 2 Jan 2013 17:57:34 +0000 (09:57 -0800)]
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bug fixes from Ted Ts'o:
"Various bug fixes for ext4. Perhaps the most serious bug fixed is one
which could cause file system corruptions when performing file punch
operations."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: avoid hang when mounting non-journal filesystems with orphan list
ext4: lock i_mutex when truncating orphan inodes
ext4: do not try to write superblock on ro remount w/o journal
ext4: include journal blocks in df overhead calcs
ext4: remove unaligned AIO warning printk
ext4: fix an incorrect comment about i_mutex
ext4: fix deadlock in journal_unmap_buffer()
ext4: split off ext4_journalled_invalidatepage()
jbd2: fix assertion failure in jbd2_journal_flush()
ext4: check dioread_nolock on remount
ext4: fix extent tree corruption caused by hole punch
Recently I suggested using "mount -o remount,mpol=local /tmp" in NUMA
mempolicy testing. Very nasty. Reading /proc/mounts, /proc/pid/mounts
or /proc/pid/mountinfo may then corrupt one bit of kernel memory, often
in a page table (causing "Bad swap" or "Bad page map" warning or "Bad
pagetable" oops), sometimes in a vm_area_struct or rbnode or somewhere
worse. "mpol=prefer" and "mpol=prefer:Node" are equally toxic.
Recent NUMA enhancements are not to blame: this dates back to 2.6.35,
when commit e17f74af351c "mempolicy: don't call mpol_set_nodemask() when
no_context" skipped mpol_parse_str()'s call to mpol_set_nodemask(),
which used to initialize v.preferred_node, or set MPOL_F_LOCAL in flags.
With slab poisoning, you can then rely on mpol_to_str() to set the bit
for node 0x6b6b, probably in the next page above the caller's stack.
mpol_parse_str() is only called from shmem_parse_options(): no_context
is always true, so call it unused for now, and remove !no_context code.
Set v.nodes or v.preferred_node or MPOL_F_LOCAL as mpol_to_str() might
expect. Then mpol_to_str() can ignore its no_context argument also,
the mpol being appropriately initialized whether contextualized or not.
Rename its no_context unused too, and let subsequent patch remove them
(that's not needed for stable backporting, which would involve rejects).
I don't understand why MPOL_LOCAL is described as a pseudo-policy:
it's a reasonable policy which suffers from a confusing implementation
in terms of MPOL_PREFERRED with MPOL_F_LOCAL. I believe this would be
much more robust if MPOL_LOCAL were recognized in switch statements
throughout, MPOL_F_LOCAL deleted, and MPOL_PREFERRED use the (possibly
empty) nodes mask like everyone else, instead of its preferred_node
variant (I presume an optimization from the days before MPOL_LOCAL).
But that would take me too long to get right and fully tested.
Eric Wong [Tue, 1 Jan 2013 21:20:27 +0000 (21:20 +0000)]
epoll: prevent missed events on EPOLL_CTL_MOD
EPOLL_CTL_MOD sets the interest mask before calling f_op->poll() to
ensure events are not missed. Since the modifications to the interest
mask are not protected by the same lock as ep_poll_callback, we need to
ensure the change is visible to other CPUs calling ep_poll_callback.
We also need to ensure f_op->poll() has an up-to-date view of past
events which occured before we modified the interest mask. So this
barrier also pairs with the barrier in wq_has_sleeper().
This should guarantee either ep_poll_callback or f_op->poll() (or both)
will notice the readiness of a recently-ready/modified item.
This issue was encountered by Andreas Voellmy and Junchang(Jason) Wang in:
http://thread.gmane.org/gmane.linux.kernel/1408782/
Signed-off-by: Eric Wong <normalperson@yhbt.net> Cc: Hans Verkuil <hans.verkuil@cisco.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Davide Libenzi <davidel@xmailserver.org> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Mauro Carvalho Chehab <mchehab@infradead.org> Cc: David Miller <davem@davemloft.net> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andreas Voellmy <andreas.voellmy@yale.edu> Tested-by: "Junchang(Jason) Wang" <junchang.wang@yale.edu> Cc: netdev@vger.kernel.org Cc: linux-fsdevel@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Aaro Koskinen [Sun, 23 Dec 2012 20:03:36 +0000 (22:03 +0200)]
watchdog: omap_wdt: eliminate unused variable and a compiler warning
We forgot to delete this in the commit 4f4753d9 (watchdog: omap_wdt:
convert to devm_ functions), and as a result the following compilation
warning was introduced:
drivers/watchdog/omap_wdt.c: In function 'omap_wdt_remove':
drivers/watchdog/omap_wdt.c:299:19: warning: unused variable 'res' [-Wunused-variable]
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Reviewed-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Linus Torvalds [Sun, 30 Dec 2012 18:00:37 +0000 (10:00 -0800)]
Merge branch 'drm-next' of git://people.freedesktop.org/~airlied/linux
Pull DRM update from Dave Airlie:
"This is a bit larger due to me not bothering to do anything since
before Xmas, and other people working too hard after I had clearly
given up.
It's got the 3 main x86 driver fixes pulls, and a bunch of tegra
fixes, doesn't fix the Ironlake bug yet, but that does seem to be
getting closer.
- radeon: gpu reset fixes and userspace packet support
- i915: watermark fixes, workarounds, i830/845 fix,
- nouveau: nvd9/kepler microcode fixes, accel is now enabled and
working, gk106 support
- tegra: misc fixes."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (34 commits)
Revert "drm: tegra: protect DC register access with mutex"
drm: tegra: program only one window during modeset
drm: tegra: clean out old gem prototypes
drm: tegra: remove redundant tegra2_tmds_config entry
drm: tegra: protect DC register access with mutex
drm: tegra: don't leave clients host1x member uninitialized
drm: tegra: fix front_porch <-> back_porch mixup
drm/nve0/graph: fix fuc, and enable acceleration on all known chipsets
drm/nvc0/graph: fix fuc, and enable acceleration on GF119
drm/nouveau/bios: cache ramcfg strap on later chipsets
drm/nouveau/mxm: silence output if no bios data
drm/nouveau/bios: parse/display extra version component
drm/nouveau/bios: implement opcode 0xa9
drm/nouveau/bios: update gpio parsing apis to match current design
drm/nouveau: initial support for GK106
drm/radeon: add WAIT_UNTIL to evergreen VM safe reg list
drm/i915: disable shrinker lock stealing for create_mmap_offset
drm/i915: optionally disable shrinker lock stealing
drm/i915: fix flags in dma buf exporting
drm/radeon: add support for MEM_WRITE packet
...
Linus Torvalds [Sun, 30 Dec 2012 17:59:21 +0000 (09:59 -0800)]
Merge tag 'omap-late-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM cleanups for omap from Olof Johansson:
"From Tony Lindgren:
Here are few more patches to finish the omap changes for multiplatform
conversion that are not strictly fixes, but were too complex to do
with the dependencies during the merge window. Those are to move of
serial-omap.h to platform_data, and the removal of remaining
cpu_is_omap macro usage outside mach-omap2.
Then there are several trivial fixes for typos and few minimal
omap2plus_defconfig updates."
* tag 'omap-late-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arch/arm/mach-omap2/dpll3xxx.c: drop if around WARN_ON
OMAP2: Fix a typo - replace regist with register.
ARM/omap: use module_platform_driver macro
ARM: OMAP2+: PMU: Remove unused header
ARM: OMAP4: remove duplicated include from omap_hwmod_44xx_data.c
ARM: OMAP2+: omap2plus_defconfig: enable twl4030 SoC audio
ARM: OMAP2+: omap2plus_defconfig: Add tps65217 support
ARM: OMAP2+: enable devtmpfs and devtmpfs automount
ARM: OMAP2+: omap_twl: Change TWL4030_MODULE_PM_RECEIVER to TWL_MODULE_PM_RECEIVER
ARM: OMAP2+: Drop plat/cpu.h for omap2plus
ARM: OMAP: Split fb.c to remove last remaining cpu_is_omap usage
MAINTAINERS: Add an entry for omap related .dts files
Linus Torvalds [Sun, 30 Dec 2012 17:58:36 +0000 (09:58 -0800)]
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"It's been quiet over the holidays, but we have had a couple of trivial
fixes coming in for the newly introduced sunxi platform; one to add it
to the multiplatform defconfig for build coverage, and one fixup for
device tree strings."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
sunxi: Change the machine compatible string.
ARM: multi_v7_defconfig: Add ARCH_SUNXI
The 720p and 1080p entries are completely redundant, as we are matching
the table entries against <=pclk.
Also generalize the comment, as we are using those table entries even
when driving other modes than the standard TV ones.
Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Dave Airlie <airlied@redhat.com>
Lucas Stach [Wed, 19 Dec 2012 21:38:54 +0000 (21:38 +0000)]
drm: tegra: protect DC register access with mutex
Window properties are programmed through a shared aperture and have to
happen atomically. Also we do the read-update-write dance on some of the
shared regs.
To make sure that different functions don't stumble over each other
protect the register access with a mutex.
Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Dave Airlie <airlied@redhat.com>
Lucas Stach [Wed, 19 Dec 2012 21:38:52 +0000 (21:38 +0000)]
drm: tegra: fix front_porch <-> back_porch mixup
Fixes wrong picture offset observed when using HDMI output with a
Technisat HD TV.
Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Mark Zhang <markz@nvidia.com> Tested-by: Mark Zhang <markz@nvidia.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Sun, 30 Dec 2012 03:54:12 +0000 (13:54 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-next
Some fixes for 3.8:
- Watermark fixups from Chris Wilson (4 pieces).
- 2 snb workarounds, seem to be recently added to our internal DB.
- workaround for the infamous i830/i845 hang, seems now finally solid!
Based on Chris' fix for SNA, now also for UXA/mesa&old SNA.
- Some more fixlets for shrinker-pulls-the-rug issues (Chris&me).
- Fix dma-buf flags when exporting (you).
- Disable the VGA plane if it's enabled on lid open - similar fix in
spirit to the one I've sent you last weeek, BIOS' really like to mess
with the display when closing the lid (awesome debug work from Krzysztof
Mazur).
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: disable shrinker lock stealing for create_mmap_offset
drm/i915: optionally disable shrinker lock stealing
drm/i915: fix flags in dma buf exporting
i915: ensure that VGA plane is disabled
drm/i915: Preallocate the drm_mm_node prior to manipulating the GTT drm_mm manager
drm: Export routines for inserting preallocated nodes into the mm manager
drm/i915: don't disable disconnected outputs
drm/i915: Implement workaround for broken CS tlb on i830/845
drm/i915: Implement WaSetupGtModeTdRowDispatch
drm/i915: Implement WaDisableHiZPlanesWhenMSAAEnabled
drm/i915: Prefer CRTC 'active' rather than 'enabled' during WM computations
drm/i915: Clear self-refresh watermarks when disabled
drm/i915: Double the cursor self-refresh latency on Valleyview
drm/i915: Fixup cursor latency used for IVB lp3 watermarks
Dave Airlie [Sun, 30 Dec 2012 03:02:48 +0000 (13:02 +1000)]
Merge branch 'drm-fixes-3.8' of git://people.freedesktop.org/~agd5f/linux into drm-next
Misc fixes for reset and new packets for userspace usage.
* 'drm-fixes-3.8' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: add WAIT_UNTIL to evergreen VM safe reg list
drm/radeon: add support for MEM_WRITE packet
drm/radeon: restore modeset late in GPU reset path
drm/radeon: avoid deadlock in pm path when waiting for fence
drm/radeon: don't leave fence blocked process on failed GPU reset
Dave Airlie [Sun, 30 Dec 2012 03:01:52 +0000 (13:01 +1000)]
Merge branch 'drm-nouveau-fixes-3.8' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-next
Fixes the accel support for nvd9 + kepler chipsets, also fixes GK106 support.
* 'drm-nouveau-fixes-3.8' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nve0/graph: fix fuc, and enable acceleration on all known chipsets
drm/nvc0/graph: fix fuc, and enable acceleration on GF119
drm/nouveau/bios: cache ramcfg strap on later chipsets
drm/nouveau/mxm: silence output if no bios data
drm/nouveau/bios: parse/display extra version component
drm/nouveau/bios: implement opcode 0xa9
drm/nouveau/bios: update gpio parsing apis to match current design
drm/nouveau: initial support for GK106
Zlatko Calusic [Fri, 28 Dec 2012 02:16:38 +0000 (03:16 +0100)]
mm: fix null pointer dereference in wait_iff_congested()
An unintended consequence of commit 4ae0a48b5efc ("mm: modify
pgdat_balanced() so that it also handles order-0") is that
wait_iff_congested() can now be called with NULL 'struct zone *'
producing kernel oops like this:
Olof Johansson [Fri, 28 Dec 2012 07:53:01 +0000 (08:53 +0100)]
Merge tag 'sunxi-fixes-for-3.8-rc2' of git://github.com/mripard/linux into fixes
From Maxime Ripard:
Fixes for the sunxi core to be merged in 3.8-rc2
* tag 'sunxi-fixes-for-3.8-rc2' of git://github.com/mripard/linux:
sunxi: Change the machine compatible string.
ARM: multi_v7_defconfig: Add ARCH_SUNXI
We should not set con->state to CLOSED here; that happens in
ceph_fault() in the caller, where it first asserts that the state
is not yet CLOSED. Avoids a BUG when the features don't match.
Since the fail_protocol() has become a trivial wrapper, replace
calls to it with direct calls to reset_connection().
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com>
Alex Elder [Wed, 26 Dec 2012 16:43:57 +0000 (10:43 -0600)]
libceph: WARN, don't BUG on unexpected connection states
A number of assertions in the ceph messenger are implemented with
BUG_ON(), killing the system if connection's state doesn't match
what's expected. At this point our state model is (evidently) not
well understood enough for these assertions to trigger a BUG().
Convert all BUG_ON(con->state...) calls to be WARN_ON(con->state...)
so we learn about these issues without killing the machine.
We now recognize that a connection fault can occur due to a socket
closure at any time, regardless of the state of the connection. So
there is really nothing we can assert about the state of the
connection at that point so eliminate that assertion.
Reported-by: Ugis <ugis22@gmail.com> Tested-by: Ugis <ugis22@gmail.com> Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com>
Alex Elder [Wed, 26 Dec 2012 20:31:40 +0000 (14:31 -0600)]
libceph: always reset osds when kicking
When ceph_osdc_handle_map() is called to process a new osd map,
kick_requests() is called to ensure all affected requests are
updated if necessary to reflect changes in the osd map. This
happens in two cases: whenever an incremental map update is
processed; and when a full map update (or the last one if there is
more than one) gets processed.
In the former case, the kick_requests() call is followed immediately
by a call to reset_changed_osds() to ensure any connections to osds
affected by the map change are reset. But for full map updates
this isn't done.
Both cases should be doing this osd reset.
Rather than duplicating the reset_changed_osds() call, move it into
the end of kick_requests().
Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com>
Alex Elder [Wed, 19 Dec 2012 21:52:36 +0000 (15:52 -0600)]
libceph: move linger requests sooner in kick_requests()
The kick_requests() function is called by ceph_osdc_handle_map()
when an osd map change has been indicated. Its purpose is to
re-queue any request whose target osd is different from what it
was when it was originally sent.
It is structured as two loops, one for incomplete but registered
requests, and a second for handling completed linger requests.
As a special case, in the first loop if a request marked to linger
has not yet completed, it is moved from the request list to the
linger list. This is as a quick and dirty way to have the second
loop handle sending the request along with all the other linger
requests.
Because of the way it's done now, however, this quick and dirty
solution can result in these incomplete linger requests never
getting re-sent as desired. The problem lies in the fact that
the second loop only arranges for a linger request to be sent
if it appears its target osd has changed. This is the proper
handling for *completed* linger requests (it avoids issuing
the same linger request twice to the same osd).
But although the linger requests added to the list in the first loop
may have been sent, they have not yet completed, so they need to be
re-sent regardless of whether their target osd has changed.
The first required fix is we need to avoid calling __map_request()
on any incomplete linger request. Otherwise the subsequent
__map_request() call in the second loop will find the target osd
has not changed and will therefore not re-send the request.
Second, we need to be sure that a sent but incomplete linger request
gets re-sent. If the target osd is the same with the new osd map as
it was when the request was originally sent, this won't happen.
This can be fixed through careful handling when we move these
requests from the request list to the linger list, by unregistering
the request *before* it is registered as a linger request. This
works because a side-effect of unregistering the request is to make
the request's r_osd pointer be NULL, and *that* will ensure the
second loop actually re-sends the linger request.
Processing of such a request is done at that point, so continue with
the next one once it's been moved.
Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com>
Linus Torvalds [Thu, 27 Dec 2012 18:46:47 +0000 (10:46 -0800)]
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Report i2c errors to userspace in lm73 driver
- Fix problem with DIV_ROUND_CLOSEST and unsigned divisors in emc6w201
driver
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (emc6w201) Fix DIV_ROUND_CLOSEST problem with unsigned divisors
hwmon: (lm73} Detect and report i2c bus errors
Linus Torvalds [Thu, 27 Dec 2012 18:42:46 +0000 (10:42 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull namespace fixes from Eric Biederman:
"This tree includes two bug fixes for problems Oleg spotted on his
review of the recent pid namespace work. A small fix to not enable
bottom halves with irqs disabled, and a trivial build fix for f2fs
with user namespaces enabled."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
f2fs: Don't assign e_id in f2fs_acl_from_disk
proc: Allow proc_free_inum to be called from any context
pidns: Stop pid allocation when init dies
pidns: Outlaw thread creation after unshare(CLONE_NEWPID)
1) GRE tunnel drivers don't set the transport header properly, they also
blindly deref the inner protocol ipv4 and needs some checks. Fixes
from Isaku Yamahata.
2) Fix sleeps while atomic in netdevice rename code, from Eric Dumazet.
3) Fix double-spinlock in solos-pci driver, from Dan Carpenter.
4) More ARP bug fixes. Fix lockdep splat in arp_solicit() and then the
bug accidentally added by that fix. From Eric Dumazet and Cong Wang.
5) Remove some __dev* annotations that slipped back in, as well as all
HOTPLUG references. From Greg KH
6) RDS protocol uses wrong interfaces to access scatter-gather elements,
causing a regression. From Mike Marciniszyn.
7) Fix build error in cpts driver, from Richard Cochran.
8) Fix arithmetic in packet scheduler, from Stefan Hasko.
9) Similarly, fix association during calculation of random backoff in
batman-adv. From Akinobu Mita.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
ipv6/ip6_gre: set transport header correctly
ipv4/ip_gre: set transport header correctly to gre header
IB/rds: suppress incompatible protocol when version is known
IB/rds: Correct ib_api use with gs_dma_address/sg_dma_len
net/vxlan: Use the underlying device index when joining/leaving multicast groups
tcp: should drop incoming frames without ACK flag set
netprio_cgroup: define sk_cgrp_prioidx only if NETPRIO_CGROUP is enabled
cpts: fix a run time warn_on.
cpts: fix build error by removing useless code.
batman-adv: fix random jitter calculation
arp: fix a regression in arp_solicit()
net: sched: integer overflow fix
CONFIG_HOTPLUG removal from networking core
Drivers: network: more __dev* removal
bridge: call br_netpoll_disable in br_add_if
ipv4: arp: fix a lockdep splat in arp_solicit()
tuntap: dont use a private kmem_cache
net: devnet_rename_seq should be a seqcount
ip_gre: fix possible use after free
ip_gre: make ipgre_tunnel_xmit() not parse network header as IP unconditionally
...
Theodore Ts'o [Thu, 27 Dec 2012 06:42:50 +0000 (01:42 -0500)]
ext4: avoid hang when mounting non-journal filesystems with orphan list
When trying to mount a file system which does not contain a journal,
but which does have a orphan list containing an inode which needs to
be truncated, the mount call with hang forever in
ext4_orphan_cleanup() because ext4_orphan_del() will return
immediately without removing the inode from the orphan list, leading
to an uninterruptible loop in kernel code which will busy out one of
the CPU's on the system.
This can be trivially reproduced by trying to mount the file system
found in tests/f_orphan_extents_inode/image.gz from the e2fsprogs
source tree. If a malicious user were to put this on a USB stick, and
mount it on a Linux desktop which has automatic mounts enabled, this
could be considered a potential denial of service attack. (Not a big
deal in practice, but professional paranoids worry about such things,
and have even been known to allocate CVE numbers for such problems.)
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Reviewed-by: Zheng Liu <wenqing.lz@taobao.com> Cc: stable@vger.kernel.org
Theodore Ts'o [Thu, 27 Dec 2012 06:42:48 +0000 (01:42 -0500)]
ext4: lock i_mutex when truncating orphan inodes
Commit c278531d39 added a warning when ext4_flush_unwritten_io() is
called without i_mutex being taken. It had previously not been taken
during orphan cleanup since races weren't possible at that point in
the mount process, but as a result of this c278531d39, we will now see
a kernel WARN_ON in this case. Take the i_mutex in
ext4_orphan_cleanup() to suppress this warning.
Reported-by: Alexander Beregalov <a.beregalov@gmail.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Reviewed-by: Zheng Liu <wenqing.lz@taobao.com> Cc: stable@vger.kernel.org
Isaku Yamahata [Mon, 24 Dec 2012 16:51:04 +0000 (16:51 +0000)]
ipv6/ip6_gre: set transport header correctly
ip6gre_xmit2() incorrectly sets transport header to inner payload
instead of GRE header. It seems copy-and-pasted from ipip.c.
Set transport header to gre header.
(In ipip case the transport header is the inner ip header, so that's
correct.)
Found by inspection. In practice the incorrect transport header
doesn't matter because the skb usually is sent to another net_device
or socket, so the transport header isn't referenced.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
Isaku Yamahata [Mon, 24 Dec 2012 16:51:03 +0000 (16:51 +0000)]
ipv4/ip_gre: set transport header correctly to gre header
ipgre_tunnel_xmit() incorrectly sets transport header to inner payload
instead of GRE header. It seems copy-and-pasted from ipip.c.
So set transport header to gre header.
(In ipip case the transport header is the inner ip header, so that's
correct.)
Found by inspection. In practice the incorrect transport header
doesn't matter because the skb usually is sent to another net_device
or socket, so the transport header isn't referenced.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
Yan Burman [Thu, 20 Dec 2012 03:36:08 +0000 (03:36 +0000)]
net/vxlan: Use the underlying device index when joining/leaving multicast groups
The socket calls from vxlan to join/leave multicast group aren't
using the index of the underlying device, as a result the stack uses
the first interface that is up. This results in vxlan being non functional
over a device which isn't the 1st to be up.
Fix this by providing the iflink field to the vxlan instance
to the multicast calls.
Signed-off-by: Yan Burman <yanb@mellanox.com> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 26 Dec 2012 12:44:34 +0000 (12:44 +0000)]
tcp: should drop incoming frames without ACK flag set
In commit 96e0bf4b5193d (tcp: Discard segments that ack data not yet
sent) John Dykstra enforced a check against ack sequences.
In commit 354e4aa391ed5 (tcp: RFC 5961 5.2 Blind Data Injection Attack
Mitigation) I added more safety tests.
But we missed fact that these tests are not performed if ACK bit is
not set.
RFC 793 3.9 mandates TCP should drop a frame without ACK flag set.
" fifth check the ACK field,
if the ACK bit is off drop the segment and return"
Not doing so permits an attacker to only guess an acceptable sequence
number, evading stronger checks.
Many thanks to Zhiyun Qian for bringing this issue to our attention.
See :
http://web.eecs.umich.edu/~zhiyunq/pub/ccs12_TCP_sequence_number_inference.pdf
Reported-by: Zhiyun Qian <zhiyunq@umich.edu> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Nandita Dukkipati <nanditad@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: John Dykstra <john.dykstra1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log