Laxman Dewangan [Mon, 2 Dec 2013 13:09:57 +0000 (18:39 +0530)]
ARM: tegra: convert device tree files to use key defines
Use key code macros for all key code refernced for keys.
For tegra20-seaboard.dts and tegra20-harmony.dts:
The key comment for key (16th row and 1st column) is KEY_KPSLASH but
code is 0x004e which is the key code for KEY_KPPLUS. As there other
key exist with KY_KPPLUS, I am assuming key code is wrong and comment
is fine. With this assumption, I am keeping the key code as KEY_KPSLASH.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Wed, 4 Dec 2013 00:26:12 +0000 (17:26 -0700)]
ARM: tegra: add sound card to Venice2 DT
Venice2 uses the MAX98090 audio CODEC, and supports built-in speakers,
and a combo headphones/microphone jack. Add a top-level sound card node
to represent this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Wed, 4 Dec 2013 22:05:51 +0000 (15:05 -0700)]
ARM: tegra: add audio-related device to Tegra124 DT
Tegra124 contains a similar set of audio devices to previous Tegra chips.
Specifically, there is an AHUB device which contains DMA FIFOs and audio
routing, and which hosts various audio-related components such as I2S
controllers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Tue, 3 Dec 2013 23:44:35 +0000 (16:44 -0700)]
ARM: tegra: enable I2C controllers on Venice2
Enable all the I2C controllers that are wired up on Venice2. I don't
know the correct I2C bus clock rates, so set them all to a conservative
100KHz for now.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Thu, 31 Oct 2013 23:23:05 +0000 (17:23 -0600)]
ARM: tegra: add MMC controllers to Tegra124 DT
Tegra124 has 4 MMC controllers just like previous versions of the SoC.
Note that there are some non-backwards-compatible HW differences, and
hence a new DT compatible value must be used to describe the HW.
Also enable the relevant controllers in the Venice2 board DT.
Stephen Warren [Fri, 15 Nov 2013 19:22:53 +0000 (12:22 -0700)]
ARM: tegra: add APB DMA controller to Tegra124 DT
Instantiate the APB DMA controller in the Tegra124 DT, and add all
DMA-related properties to other DT nodes that rely on (reference) the
DMA controller's node.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Thierry Reding <treding@nvidia.com>
Stephen Warren [Thu, 7 Nov 2013 19:20:57 +0000 (12:20 -0700)]
ARM: tegra: add reset properties to Tegra124 DTs
The DT bindings now require module resets to be specified. The earlier
patches which added these nodes were originally written before that
requirement.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Thierry Reding <treding@nvidia.com>
Stephen Warren [Tue, 26 Nov 2013 21:43:45 +0000 (14:43 -0700)]
ARM: tegra: fix node sort order
For Tegra DT files, I've been attempting to keep the nodes sorted in
the order:
1) Nodes with reg, in order of reg.
2) Nodes without reg, alphabetically.
This patch fixes a few escapees that I missed:-(
The diffs look larger than they really are, because sometimes when one
node was moved up or down, diff chose to represent this as many other
nodes being moved the other way!
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Tue, 26 Nov 2013 00:53:16 +0000 (17:53 -0700)]
ARM: tegra: add missing unit addresses to DT
DT node names should include a unit address iff the node has a reg
property. For Tegra DTs at least, we were previously applying a different
rule, namely that node names only needed to include a unit address if it
was required to make the node name unique. Consequently, many unit
addresses are missing. Add them.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
WingMan Kwok [Wed, 4 Dec 2013 18:51:56 +0000 (13:51 -0500)]
ARM: keystone: defconfig: enable USB support
Enable the USB support (Host mode only) on TI's Keystone platform.
It also enables the support of usb mass storage, FAT and Ext4
filesystems to test rootfs mount over an USB disk.
With commit 4178bac4f {ARM: call of_clk_init from default time_init
handler}, of_clk_init() is always called on machines using default
time_init handler.
So drop the of_clk_init() from keystone code to avoid below
boot errors because of double call.
ARM: keystone: Make PM bus ready before populating platform devices
Keystone PM bus makes use of generic PM clock core backend. Since
generic PM clock core uses platform bus notifiers to track events like
ADD_DEVICE/DEL_DEVICE and to fill clock lists per each device, we need
to initialise Keystone PM domains before the platform devices have been
created.
Hence, fix it by moving keystone_pm_runtime_init() before platform
devices have been populated.
Keystone II peripheral devices support 32-bit DMA and hence can access only
first 2GB of the memory address space. So set the platform dma_zone_size
to handle that case.
Thierry Reding [Fri, 13 Dec 2013 16:31:04 +0000 (17:31 +0100)]
ARM: tegra: Special-case the 3D clamps on Tegra124
A separate register is used to remove the clamps for the GPU on
Tegra124. In order to be able to use the same API, special-case
this particular partition.
Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Drivers can use the tegra_powergate_remove_clamping() API during
initialization. In order to allow such drivers to be built as modules,
export the symbol.
Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Dan Carpenter [Mon, 16 Dec 2013 14:02:10 +0000 (17:02 +0300)]
spi: tegra: checking for ERR_PTR instead of NULL
dma_request_slave_channel() returns NULL on error and not ERR_PTRs.
I've fixed this by using dma_request_slave_channel_reason() which does
return ERR_PTRs.
Fixes: a915d150f68d ('spi: tegra: convert to standard DMA DT bindings') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Uwe Kleine-König [Thu, 17 Nov 2011 13:36:23 +0000 (14:36 +0100)]
ARM: new platform for Energy Micro's EFM32 Cortex-M3 SoCs
There are still some missing parts (e.g. board support, device trees),
but with these bits added on top of this patch I can successfully boot a
EFM32GG-DK3750 board that uses an EFM32GG990F1024.
Matias Bjorling [Tue, 10 Dec 2013 15:50:38 +0000 (16:50 +0100)]
null_blk: mem garbage on NUMA systems during init
For NUMA systems, initializing the blk-mq layer and using per node hctx.
We initialize submit queues to 1, while blk-mq nr_hw_queues is
initialized to the number of NUMA nodes.
This makes the null_init_hctx function overwrite memory outside of what
it allocated. In my case it lead to writing garbage into struct
request_queue's mq_map.
radeon_pm: fix oops in hwmon_attributes_visible() and radeon_hwmon_show_temp_thresh()
Since commit ec39f64bba34 ("drm/radeon/dpm: Convert to use
devm_hwmon_register_with_groups") radeon_hwmon_init() is using
hwmon_device_register_with_groups(), which sets `rdev' as a device
private driver_data, while hwmon_attributes_visible() and
radeon_hwmon_show_temp_thresh() are still waiting for `drm_device'.
Fix them by using dev_get_drvdata(), in order to avoid this oops:
1) Revert CHECKSUM_COMPLETE optimization in pskb_trim_rcsum(), I can't
figure out why it breaks things.
2) Fix comparison in netfilter ipset's hash_netnet4_data_equal(), it
was basically doing "x == x", from Dave Jones.
3) Freescale FEC driver was DMA mapping the wrong number of bytes, from
Sebastian Siewior.
4) Blackhole and prohibit routes in ipv6 were not doing the right thing
because their ->input and ->output methods were not being assigned
correctly. Now they behave properly like their ipv4 counterparts.
From Kamala R.
5) Several drivers advertise the NETIF_F_FRAGLIST capability, but
really do not support this feature and will send garbage packets if
fed fraglist SKBs. From Eric Dumazet.
6) Fix long standing user triggerable BUG_ON over loopback in RDS
protocol stack, from Venkat Venkatsubra.
7) Several not so common code paths can potentially try to invoke
packet scheduler actions that might be NULL without checking. Shore
things up by either 1) defining a method as mandatory and erroring
on registration if that method is NULL 2) defininig a method as
optional and the registration function hooks up a default
implementation when NULL is seen. From Jamal Hadi Salim.
8) Fix fragment detection in xen-natback driver, from Paul Durrant.
9) Kill dangling enter_memory_pressure method in cg_proto ops, from
Eric W Biederman.
10) SKBs that traverse namespaces should have their local_df cleared,
from Hannes Frederic Sowa.
11) IOCB file position is not being updated by macvtap_aio_read() and
tun_chr_aio_read(). From Zhi Yong Wu.
12) Don't free virtio_net netdev before releasing all of the NAPI
instances. From Andrey Vagin.
13) Procfs entry leak in xt_hashlimit, from Sergey Popovich.
14) IPv6 routes that are no cached routes should not count against the
garbage collection limits. We had this almost right, but were
missing handling addrconf generated routes properly. From Hannes
Frederic Sowa.
15) fib{4,6}_rule_suppress() have to consider potentially seeing NULL
route info when they are called, from Stefan Tomanek.
16) TUN and MACVTAP have had truncated packet signalling for some time,
fix from Jason Wang.
17) Fix use after frrr in __udp4_lib_rcv(), from Eric Dumazet.
18) xen-netback does not interpret the NAPI budget properly for TX work,
fix from Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
igb: Fix for issue where values could be too high for udelay function.
i40e: fix null dereference
xen-netback: fix gso_prefix check
net: make neigh_priv_len in struct net_device 16bit instead of 8bit
drivers: net: cpsw: fix for cpsw crash when build as modules
xen-netback: napi: don't prematurely request a tx event
xen-netback: napi: fix abuse of budget
sch_tbf: use do_div() for 64-bit divide
udp: ipv4: must add synchronization in udp_sk_rx_dst_set()
net:fec: remove duplicate lines in comment about errata ERR006358
Revert "8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature"
8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature
xen-netback: make sure skb linear area covers checksum field
net: smc91x: Fix device tree based configuration so it's usable
udp: ipv4: fix potential use after free in udp_v4_early_demux()
macvtap: signal truncated packets
tun: unbreak truncated packet signalling
net: sched: htb: fix the calculation of quantum
net: sched: tbf: fix the calculation of max_size
micrel: add support for KSZ8041RNLI
...
Linus Torvalds [Sun, 15 Dec 2013 19:52:47 +0000 (11:52 -0800)]
Merge branch 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"This is a pretty small batch:
The biggest single change is to stop using EFI time services on 32-bit
platforms. This matches our current behavior on 64-bit platforms as
we already had ruled them out there as being too unreliable. Turns
out that affects 32-bit platforms, too.
One NULL pointer fix for SGI UV.
Two minor build fixes, one of which only affects icc and the other
which affects icc and future versions or nonstandard default settings
of gcc"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: Don't use (U)EFI time services on 32 bit
x86, build, icc: Remove uninitialized_var() from compiler-intel.h
x86/UV: Fix NULL pointer dereference in uv_flush_tlb_others() if the 'nobau' boot option is used
x86, build: Pass in additional -mno-mmx, -mno-sse options
This patch adds the mmc device tree node entries for exynos5420 SOC.
Exynos5420 has a different version of DWMMC controller,so a new
compatible string is used to distinguish it from the prior SOC's.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch rename's the device tree mmc node's from "dwmmc" to "mmc".
According to ePAPR chapter 2.2.2 generic node name recommendation,
it has been opted change from dwmmc to mmc.Also this patch remove the
instance index from the node name.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Linus Torvalds [Sun, 15 Dec 2013 19:45:27 +0000 (11:45 -0800)]
Merge tag 'pci-v3.13-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI device hotplug
- Move device_del() from pci_stop_dev() to pci_destroy_dev() (Rafael
Wysocki)
Host bridge drivers
- Update maintainers for DesignWare, i.MX6, Armada, R-Car (Bjorn
Helgaas)
- mvebu: Return 'unsupported' for Interrupt Line and Interrupt Pin
(Jason Gunthorpe)
Miscellaneous
- Avoid unnecessary CPU switch when calling .probe() (Alexander
Duyck)
- Revert "workqueue: allow work_on_cpu() to be called recursively"
(Bjorn Helgaas)
- Disable Bus Master only on kexec reboot (Khalid Aziz)
- Omit PCI ID macro strings to shorten quirk names for LTO (Michal
Marek)"
* tag 'pci-v3.13-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Add DesignWare, i.MX6, Armada, R-Car PCI host maintainers
PCI: Disable Bus Master only on kexec reboot
PCI: mvebu: Return 'unsupported' for Interrupt Line and Interrupt Pin
PCI: Omit PCI ID macro strings to shorten quirk names
PCI: Move device_del() from pci_stop_dev() to pci_destroy_dev()
Revert "workqueue: allow work_on_cpu() to be called recursively"
PCI: Avoid unnecessary CPU switch when calling driver .probe() method
ARM: dts: Move fifo-depth property from exynos5250 board dts
As fifo-depth property in dw_mmc device tree node is SOC
specific, move this property to exynos5250 SOC specific
file.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com>
[kgene.kim@samsung.com: squashed fifo-depth patch for cros5250-common] Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ARM: dts: change status property of dwmmc nodes for exynos5250
According to ePAPR, chapter 2.3.4, the status property has
defined that it should be set to "disabled" when "the device
is not presently operational, but it might become operational
in the future".
So this patch disable dwmmc node by "status = disabled" in SOC
dts file and enable dwmmc node by "status = okay" in board specific
dts file.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Linus Torvalds [Sun, 15 Dec 2013 19:28:02 +0000 (11:28 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull SELinux fixes from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selinux: process labeled IPsec TCP SYN-ACK packets properly in selinux_ip_postroute()
selinux: look for IPsec labels on both inbound and outbound packets
selinux: handle TCP SYN-ACK packets correctly in selinux_ip_postroute()
selinux: handle TCP SYN-ACK packets correctly in selinux_ip_output()
selinux: fix possible memory leak
and Josh Boyer bisected it down to this commit. Reverting the commit in
the rawhide kernel fixes the problem.
Eric Paris root-caused it to incorrect subtype matching in that commit
breaking fuse, and has a tentative patch, but by now we're better off
retrying this in 3.14 rather than playing with it any more.
Reported-by: Tom London <selinux@gmail.com> Bisected-by: Josh Boyer <jwboyer@fedoraproject.org> Acked-by: Eric Paris <eparis@redhat.com> Cc: James Morris <jmorris@namei.org> Cc: Anand Avati <avati@redhat.com> Cc: Paul Moore <paul@paul-moore.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tomasz Figa [Sun, 20 Oct 2013 21:56:51 +0000 (06:56 +0900)]
ARM: S3C64XX: Select CPU_V6K instead of CPU_V6
All S3C64XX SoCs come with ARM1176JZF-s core, which fully supports
ARMv6K extensions. This patch lets the kernel use them on S3C6410 by
adding selection of CPU_V6K to ARCH_S3C64XX.
To use V6K extensions, these symbols must not be selected at the same
time, so this patch keeps only CPU_V6K selected for S3C64XX.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Carolyn Wyborny [Sat, 14 Dec 2013 11:26:46 +0000 (03:26 -0800)]
igb: Fix for issue where values could be too high for udelay function.
This patch changes the igb_phy_has_link function to check the value of the
parameter before deciding to use udelay or mdelay in order to be sure that
the value is not too high for udelay function.
CC: stable kernel <stable@vger.kernel.org> # 3.9+ Signed-off-by: Sunil K Pandey <sunil.k.pandey@intel.com> Signed-off-by: Kevin B Smith <kevin.b.smith@intel.com> Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Brandeburg [Sat, 14 Dec 2013 11:26:45 +0000 (03:26 -0800)]
i40e: fix null dereference
If the vsi->tx_rings structure is NULL we don't want to panic.
Change-Id: Ic694f043701738c434e8ebe0caf0673f4410dc10 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tomasz Figa [Fri, 13 Dec 2013 19:59:39 +0000 (20:59 +0100)]
ARM: s3c64xx: dt: Fix boot failure due to double clock initialization
Commit
4178bac ARM: call of_clk_init from default time_init handler
added implicit call to of_clk_init() from default time_init callback,
but it did not change platforms calling it from other callbacks, despite
of not having custom time_init callbacks. This caused double clock
initialization on such platforms, leading to boot failures. An example
of such platform is mach-s3c64xx.
This patch fixes boot failure on s3c64xx by dropping custom init_irq
callback, which had a call to of_clk_init() and moving system reset
initialization to init_machine callback. This allows us to have
clocks initialized properly without a need to have custom init_time or
init_irq callbacks.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Sat, 14 Dec 2013 00:16:03 +0000 (16:16 -0800)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"This resolves some further issues with the dma mask changes on ARM
which have been found by TI and others, and also some corner cases
with the updates to the virtual to physical address translations.
Konstantin also found some problems with the unwinder, which now
performs tighter verification that the stack is valid while unwinding"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: fix asm/memory.h build error
ARM: 7917/1: cacheflush: correctly limit range of memory region being flushed
ARM: 7913/1: fix framepointer check in unwind_frame
ARM: 7912/1: check stack pointer in get_wchan
ARM: 7909/1: mm: Call setup_dma_zone() post early_paging_init()
ARM: 7908/1: mm: Fix the arm_dma_limit calculation
ARM: another fix for the DMA mapping checks
Linus Torvalds [Sat, 14 Dec 2013 00:14:39 +0000 (16:14 -0800)]
Merge tag 'arc-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"These are couple of weeks old already, but I just couldn't get them to
you earlier.
- couple of fixes for recently added perf code
- build time extable sort"
* tag 'arc-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [perf] Fix a few thinkos
ARC: Add guard macro to uapi/asm/unistd.h
ARC: extable: Enable sorting at build time
Linus Torvalds [Fri, 13 Dec 2013 21:22:22 +0000 (13:22 -0800)]
Merge tag 'dm-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"A set of device-mapper fixes for 3.13.
A fix for possible memory corruption during DM table load, fix a
possible leak of snapshot space in case of a crash, fix a possible
deadlock due to a shared workqueue in the delay target, fix to
initialize read-only module parameters that are used to export metrics
for dm stats and dm bufio.
Quite a few stable fixes were identified for both the thin-
provisioning and caching targets as a result of increased regression
testing using the device-mapper-test-suite (dmts). The most notable
of these are the reference counting fixes for the space map btree that
is used by the dm-array interface -- without these the dm-cache
metadata will leak, resulting in dm-cache devices running out of
metadata blocks. Also, some important fixes related to the
thin-provisioning target's transition to read-only mode on error"
* tag 'dm-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm array: fix a reference counting bug in shadow_ablock
dm space map: disallow decrementing a reference count below zero
dm stats: initialize read-only module parameter
dm bufio: initialize read-only module parameters
dm cache: actually resize cache
dm cache: update Documentation for invalidate_cblocks's range syntax
dm cache policy mq: fix promotions to occur as expected
dm thin: allow pool in read-only mode to transition to read-write mode
dm thin: re-establish read-only state when switching to fail mode
dm thin: always fallback the pool mode if commit fails
dm thin: switch to read-only mode if metadata space is exhausted
dm thin: switch to read only mode if a mapping insert fails
dm space map metadata: return on failure in sm_metadata_new_block
dm table: fail dm_table_create on dm_round_up overflow
dm snapshot: avoid snapshot space leak on crash
dm delay: fix a possible deadlock due to shared workqueue
Russell King [Tue, 10 Dec 2013 19:21:08 +0000 (19:21 +0000)]
ARM: fix asm/memory.h build error
Jason Gunthorpe reports a build failure when ARM_PATCH_PHYS_VIRT is
not defined:
In file included from arch/arm/include/asm/page.h:163:0,
from include/linux/mm_types.h:16,
from include/linux/sched.h:24,
from arch/arm/kernel/asm-offsets.c:13:
arch/arm/include/asm/memory.h: In function '__virt_to_phys':
arch/arm/include/asm/memory.h:244:40: error: 'PHYS_OFFSET' undeclared (first use in this function)
arch/arm/include/asm/memory.h:244:40: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/include/asm/memory.h: In function '__phys_to_virt':
arch/arm/include/asm/memory.h:249:13: error: 'PHYS_OFFSET' undeclared (first use in this function)
Fixes: ca5a45c06cd4 ("ARM: mm: use phys_addr_t appropriately in p2v and v2p conversions") Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Not all Tegra devices can set the CPU reset handler in the same way.
In particular, devices using a TrustZone secure monitor cannot set it
up directly and need to ask the firmware to do it.
This patch separates the act of setting the reset handler from its
preparation, so the former can be implemented in a different way.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Trusted Foundations is a TrustZone-based secure monitor for ARM that
can be invoked using the same SMC-based API on supported platforms.
This patch adds initial basic support for Trusted Foundations using
the ARM firmware API. Current features are limited to the ability to
boot secondary processors.
Note: The API followed by Trusted Foundations does *not* follow the SMC
calling conventions. It has nothing to do with PSCI neither and is only
relevant to devices that use Trusted Foundations (like most Tegra-based
retail devices).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Linus Torvalds [Fri, 13 Dec 2013 19:39:54 +0000 (11:39 -0800)]
Merge tag 'regulator-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A small set of driver fixes plus one larger core change which changes
the way we check to see if we're using DT so that there aren't any
races between deciding we're using DT and the regulator subsystem
noticing.
This makes the new support for substituting a dummy regulator and
optional regulators work a lot better on DT systems since it ensures
that we don't trigger probe deferral when we shouldn't which was
causing bugs in clients"
* tag 'regulator-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: pfuze100: allow misprogrammed ID
regulator: pfuze100: Fix address of FABID
regulator: as3722: set the correct current limit
regulator: core: Check for DT every time we check full constraints
regulator: core: Replace checks of have_full_constraints with a function
Linus Torvalds [Fri, 13 Dec 2013 19:38:35 +0000 (11:38 -0800)]
Merge tag 'regmap-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"Two small changes to fix some error handling and checking (both of
which would be quite serious if the errors trigger) plus a trivial
documentation fix"
* tag 'regmap-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: use IS_ERR() to check clk_get() results
regmap: make sure we unlock on failure in regmap_bulk_write
regmap: trivial comment fix (copy'n'paste error)
Linus Torvalds [Fri, 13 Dec 2013 19:37:57 +0000 (11:37 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Here are two simple but wanted fixes for the i2c subsystem"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: imx: Check the return value from clk_prepare_enable()
i2c: mux: Inherit retry count and timeout from parent for muxed bus
Stephen Warren [Wed, 4 Dec 2013 21:17:14 +0000 (14:17 -0700)]
ARM: tegra: tegra_defconfig updates
Add some features to tegra_defconfig:
* Tegra+MAX98090 audio machine driver, as used on the Venice2 board.
* AMX3722 PMIC, as used on the Venice2 board.
* ChromeOS embedded controller, for the Venice2 keyboard.
Also, rebuild tegra_defconfig on a more recent kernel (3.13-rc1) to
minimize irrelevant diffs showing up when people edit the file.
Linus Torvalds [Fri, 13 Dec 2013 19:31:22 +0000 (11:31 -0800)]
Merge tag 'for-linus-20131212' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"Two MTD fixes, for the pxa3xx-nand driver:
- This driver was not ready to fully Armada 370 NAND, with
particularly notable problems seen on flash with 2KB page sizes.
This "compatible" entry really should have been held back until
3.14 or later.
- Fix a bug seen in rare cases on the error path of a failed probe
attempt, where we free unallocated DMA resources"
* tag 'for-linus-20131212' of git://git.infradead.org/linux-mtd:
mtd: nand: pxa3xx: Use info->use_dma to release DMA resources
Partially revert "mtd: nand: pxa3xx: Introduce 'marvell,armada370-nand' compatible string"
Linus Torvalds [Fri, 13 Dec 2013 19:29:51 +0000 (11:29 -0800)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine fixes from Vinod Koul:
"Here is the common fixes PULL for dmaengine.
Dan has been working on fixing the build issues in bunch of drivers.
Here we have one fixing s3c24xx-dma, along with fix from Russell on
pl08x. Also we have Kuninori rcar dma fixes. The s3c24xx-dma which
was added in last merge window missed updates to usage of DMA_COMPLETE
so converting the last driver"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: fix build breakage in s3c24xx-dma
Fix pl08x warnings
rcar-hpbdma: initialise plane information when halted
rcar-hpbdma: fixup channel busy check for double plane
rcar-hpbdma: add max transfer size
dma: mmp_pdma: add missing platform_set_drvdata() in mmp_pdma_probe()
dmaengine: s3c24xx-dma: use DMA_COMPLETE for dma completion status
Joe Thornber [Fri, 13 Dec 2013 12:31:08 +0000 (12:31 +0000)]
dm space map: disallow decrementing a reference count below zero
The old behaviour, returning -EINVAL if a ref_count of 0 would be
decremented, was removed in commit f722063 ("dm space map: optimise
sm_ll_dec and sm_ll_inc"). To fix this regression we return an error
code from the mutator function pointer passed to sm_ll_mutate() and have
dec_ref_count() return -EINVAL if the old ref_count is 0.
Add a DMERR to reflect the potential seriousness of this error.
Also, add missing dm_tm_unlock() to sm_ll_mutate()'s error path.
With this fix the following dmts regression test now passes:
dmtest run --suite cache -n /metadata_use_kernel/
The next patch fixes the higher-level dm-array code that exposed this
regression.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@vger.kernel.org # 3.12+
This adds initial support for the Marvell Berlin SoC family with
Armada 1500 (88DE3100) and Armada 1500-mini (88DE3005) SoCs.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Reviewed-by: Jason Cooper <jason@lakedaemon.net> Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de>
ARM: add Armada 1500-mini and Chromecast device tree files
This adds very basic device tree files for the Marvell Armada
1500-mini SoC (Berlin BG2CD) and the Google Chromecast. Currently,
SoC only has nodes for cpu, some clocks, l2 cache controller, local
timer, apb timers, uart, and interrupt controllers.
The Google Chromecast is a consumer device comprising the Armada
1500-mini SoC above.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
ARM: add Armada 1500 and Sony NSZ-GS7 device tree files
This adds very basic device tree files for the Marvell Armada 1500 SoC
(Berlin BG2) and the Sony NSZ-GS7 GoogleTV board. Currently, SoC only has
nodes for cpus, some clocks, l2 cache controller, local timer, apb timers,
uart, and interrupt controllers. The Sony NSZ-GS7 is a GoogleTV consumer
device comprising the Armada 1500 SoC above.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Reviewed-by: Jason Cooper <jason@lakedaemon.net> Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Jisheng Zhang <jszhang@marvell.com>
This adds UART0 as found on Marvell 88DE3xxx SoCs, e.g. Armada 1500
to the list of possible lowlevel debug options.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Reviewed-by: Jason Cooper <jason@lakedaemon.net> Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de>
ARM: add Marvell Berlin SoCs to multi_v7_defconfig
This adds the Marvell Berlin SoC family, Marvell Armada 1500
(BG2), and Marvell Armada 1500-mini (BG2CD) to the multi_v7_defconfig.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Reviewed-by: Jason Cooper <jason@lakedaemon.net> Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de>
ARM: add Marvell Berlin SoC familiy to Marvell doc
This adds known facts and rumors about the Marvell Berlin (88DE3xxx) SoC
family to the Marvell SoC documentation.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Reviewed-by: Jason Cooper <jason@lakedaemon.net> Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Linus Torvalds [Fri, 13 Dec 2013 02:22:10 +0000 (18:22 -0800)]
Merge branch 'akpm' (fixes from Andrew)
Merge patches from Andrew Morton:
"13 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: memcg: do not allow task about to OOM kill to bypass the limit
mm: memcg: fix race condition between memcg teardown and swapin
thp: move preallocated PTE page table on move_huge_pmd()
mfd/rtc: s5m: fix register updating by adding regmap for RTC
rtc: s5m: enable IRQ wake during suspend
rtc: s5m: limit endless loop waiting for register update
rtc: s5m: fix unsuccesful IRQ request during probe
drivers/rtc/rtc-s5m.c: fix info->rtc assignment
include/linux/kernel.h: make might_fault() a nop for !MMU
drivers/rtc/rtc-at91rm9200.c: correct alarm over day/month wrap
procfs: also fix proc_reg_get_unmapped_area() for !MMU case
mm: memcg: do not declare OOM from __GFP_NOFAIL allocations
include/linux/hugetlb.h: make isolate_huge_page() an inline
Johannes Weiner [Fri, 13 Dec 2013 01:12:35 +0000 (17:12 -0800)]
mm: memcg: do not allow task about to OOM kill to bypass the limit
Commit 4942642080ea ("mm: memcg: handle non-error OOM situations more
gracefully") allowed tasks that already entered a memcg OOM condition to
bypass the memcg limit on subsequent allocation attempts hoping this
would expedite finishing the page fault and executing the kill.
David Rientjes is worried that this breaks memcg isolation guarantees
and since there is no evidence that the bypass actually speeds up fault
processing just change it so that these subsequent charge attempts fail
outright. The notable exception being __GFP_NOFAIL charges which are
required to bypass the limit regardless.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reported-by: David Rientjes <rientjes@google.com> Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-bt: David Rientjes <rientjes@google.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Fri, 13 Dec 2013 01:12:34 +0000 (17:12 -0800)]
mm: memcg: fix race condition between memcg teardown and swapin
There is a race condition between a memcg being torn down and a swapin
triggered from a different memcg of a page that was recorded to belong
to the exiting memcg on swapout (with CONFIG_MEMCG_SWAP extension). The
result is unreclaimable pages pointing to dead memcgs, which can lead to
anything from endless loops in later memcg teardown (the page is charged
to all hierarchical parents but is not on any LRU list) or crashes from
following the dangling memcg pointer.
Memcgs with tasks in them can not be torn down and usually charges don't
show up in memcgs without tasks. Swapin with the CONFIG_MEMCG_SWAP
extension is the notable exception because it charges the cgroup that
was recorded as owner during swapout, which may be empty and in the
process of being torn down when a task in another memcg triggers the
swapin:
teardown: swapin:
lookup_swap_cgroup_id()
rcu_read_lock()
mem_cgroup_lookup()
css_tryget()
rcu_read_unlock()
disable css_tryget()
call_rcu()
offline_css()
reparent_charges()
res_counter_charge() (hierarchical!)
css_put()
css_free()
pc->mem_cgroup = dead memcg
add page to dead lru
Add a final reparenting step into css_free() to make sure any such raced
charges are moved out of the memcg before it's finally freed.
In the longer term it would be cleaner to have the css_tryget() and the
res_counter charge under the same RCU lock section so that the charge
reparenting is deferred until the last charge whose tryget succeeded is
visible. But this will require more invasive changes that will be
harder to evaluate and backport into stable, so better defer them to a
separate change set.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@suse.cz> Cc: David Rientjes <rientjes@google.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
p = mmap((void *) GB, 10 * MB, PROT_READ | PROT_WRITE,
MAP_PRIVATE | MAP_ANONYMOUS | MAP_FIXED, -1, 0);
for (i = 0; i < 10 * MB; i += 4096)
p[i] = 1;
mremap(p, 10 * MB, 10 * MB, MREMAP_FIXED | MREMAP_MAYMOVE, 2 * GB);
return 0;
}
Due to split PMD lock, we now store preallocated PTE tables for THP
pages per-PMD table. It means we need to move them to other PMD table
if huge PMD moved there.