Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Fixes for big 3 drivers:
nouveau: revert earlier MBP fix, put a dmi based MBP fix in its place
(fixes a regression we found on some Dell eDP panels doing some
internal testing)
radeon: revert pll fixes, real fix is too invasive, fix scratch leak
intel: 3 minor fixes, one for HDMI audio."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: add dmi quirk for gpio reset
drm/radeon: Prevent leak of scratch register on resume from suspend
Revert "drm/nv50-/gpio: initialise to vbios defaults during init"
Revert "drm/radeon: rework pll selection (v3)"
drm/i915: HDMI - Clear Audio Enable bit for Hot Plug
drm/i915: Reduce a pin-leak BUG into a WARN
drm/i915: enable lvds pin pairs before dpll on gen2
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Add missing 'name' sysfs attributes to ad7314 and ads7871 drivers
- Bump maximum wait time for applesmc driver (again)
- Fix build warning seen with W=1 in include/linux/kernel.h, introduced
with commit b6d86d3d6d6e ("Fix DIV_ROUND_CLOSEST to support negative
dividends")
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
linux/kernel.h: Fix warning seen with W=1 due to change in DIV_ROUND_CLOSEST
hwmon: (applesmc) Bump max wait
hwmon: (ad7314) Add 'name' sysfs attribute
hwmon: (ads7871) Add 'name' sysfs attribute
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine fixes from Vinod Koul:
"There are two trivial fixes in pl330 driver and two in at_hdmac
driver."
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
DMA: PL330: Check the pointer returned by kzalloc
DMA: PL330: Fix potential NULL pointer dereference in pl330_submit_req()
dmaengine: at_hdmac: check that each sg data length is non-null
dmaengine: at_hdmac: fix comment in atc_prep_slave_sg()
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc bug fixes from Olof Johansson:
"A couple of samsung clock locking fixes, at91 device tree gpio
configuration fix and a couple more for shmobile and i.MX.
All small targeted fixes."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM i.MX25: Make timer irq work again
ARM: imx: armadillo5x0: Fix illegal register access
ARM: shmobile: kzm9g: bugfix: correct mmcif interrupt settings
ARM: SAMSUNG: Use spin_lock_{irqsave,irqrestore} in clk_set_rate
ARM: at91: fix missing #interrupt-cells on gpio-controller
ARM: SAMSUNG: use spin_lock_irqsave() in clk_set_parent
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Bug fixes for 3.6-rc7, including some important patches for large page
related memory management issues."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/dasd: fix read unit address configuration loop
s390/dasd: fix pathgroup race
s390/mm: fix user access page-table walk code
s390/hwcaps: do not report high gprs for 31 bit kernel
s390/cio: invalidate cdev pointer before deregistration
s390/cio: fix IO subchannel event race
s390/dasd: move wake_up call
s390/hugetlb: use direct TLB flushing for hugetlbfs pages
s390/mm: fix deadlock in unmap_hugepage_range()
Merge tag 'stable/for-linus-3.6-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
- Fix M2P batching re-using the incorrect structure field.
In v3.5 we added batching for M2P override (Machine Frame Number ->
Physical Frame Number), but the original MFN was saved in an
incorrect structure - and we would oops/restore when restoring with
the old MFN.
- Disable BIOS SMP MP table search.
A bootup issue that we had ignored until we found that on DL380 G6 it
was needed.
* tag 'stable/for-linus-3.6-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/boot: Disable BIOS SMP MP table search.
xen/m2p: do not reuse kmap_op->dev_bus_addr
The format_array_alloc() function is fundamentally racy, in that it
prints the array twice: once to figure out how much space to allocate
for the buffer, and the second time to actually print out the data.
If any of the array contents changes in between, the allocation size may
be wrong, and the end result may be truncated in odd ways.
Just don't do it. Allocate a maximum-sized array up-front, and just
format the array contents once. The only user of the u32_array
interfaces is the Xen spinlock statistics code, and it has 31 entries in
the arrays, so the maximum size really isn't that big, and the end
result is much simpler code without the bug.
David Rientjes [Fri, 21 Sep 2012 09:16:29 +0000 (02:16 -0700)]
debugfs: fix race in u32_array_read and allocate array at open
u32_array_open() is racy when multiple threads read from a file with a
seek position of zero, i.e. when two or more simultaneous reads are
occurring after the non-seekable files are created. It is possible that
file->private_data is double-freed because the threads races between
kfree(file->private-data);
and
file->private_data = NULL;
The fix is to only do format_array_alloc() when the file is opened and
free it when it is closed.
Note that because the file has always been non-seekable, you can't open
it and read it multiple times anyway, so the data has always been
generated just once. The difference is that now it is generated at open
time rather than at the time of the first read, and that avoids the
race.
Reported-by: Dave Jones <davej@redhat.com> Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Tested-by: Raghavendra <raghavendra.kt@linux.vnet.ibm.com> Signed-off-by: David Rientjes <rientjes@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Airlie [Fri, 21 Sep 2012 10:46:01 +0000 (20:46 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel writes:
Essentially just flush my -fixes queue before I head off to xdc.
- gen2 regression fixer, we've enabled the lvds stuff too late. Not
causing any known issues, but this restores the sequence before a
refactor that landed in 3.5, and lvds is a fickle beast. And seriously,
who runs gen2 still ...
- downgrade a BUG to a WARN - we haven't root-caused/fixed the underlying
issue yet, but this should help bug reporters quite a bit.
- properly disable hdmi audio - we've lost track of this, which resulted
in the alsa driver again losing track of the unplug event.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: HDMI - Clear Audio Enable bit for Hot Plug
drm/i915: Reduce a pin-leak BUG into a WARN
drm/i915: enable lvds pin pairs before dpll on gen2
Simon Kitching [Thu, 20 Sep 2012 16:59:16 +0000 (12:59 -0400)]
drm/radeon: Prevent leak of scratch register on resume from suspend
Cards typically have 5-7 scratch registers; one of these is reserved for
rdev->rptr_save_reg. Unfortunately the reservation is done in function
r100_cp_init, which is called by all drivers except r600 - and this
function is also invoked on resume from suspend. After several resumes,
no scratch registers are free and graphics acceleration is disabled.
Dmesg then reports either:
*ERROR* radeon: cp failed to get scratch reg (-22).
*ERROR* radeon: cp isn't working(-22).
radeon 0000:01:00.0: failed initializing CP (-22).
or:
*ERROR* radeon: failed to get scratch reg (-22).
*ERROR* radeon: failed testing IB on GFX ring (-22).
*ERROR* ib ring test failed (-22).
The chain of calls on boot for all except r600 is:
radeon_init -> ... -> (rXXX_init) -> rXXX_startup -> r100_cp_init
The chain of calls on resume for all except r600 is:
rXXX_resume -> rXXX_startup -> r100_cp_init.
R600 correctly allocates rptr_save_reg in r600_init (ie once only, not
in resume). However moving the code into the init functions for all
drivers means touching 4 drivers. So instead, this patch just adds a
test in r100_cp_init to avoid reallocating on resume. As the rdev
structure is allocated via kzalloc in radeon_driver_load_kms, and zero
is not a valid registerid, zero safely implies not-yet-allocated.
This issue appears to have been introduced in c7eff978 (3.6.0-rcN)
Signed-off-by: Simon Kitching <skitching@vonos.net> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We discovered this causes problem on some Dell eDP laptops, so Apple
lose out for now, I might try and whip up a dmi based workaround for 3.6
but I'm not sure I'll get time.
Input: sentelic - filter out erratic movement when lifting finger
When lifing finger off the surface some versions of touchpad send movement
packets with very low coordinates, which cause cursor to jump to the upper
left corner of the screen. Let's ignore least significant bits of X and Y
coordinates if higher bits are all zeroes and consider finger not touching
the pad.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43197
Reported-and-tested-by: Aleksey Spiridonov <leks13@leks13.ru> Tested-by: Eddie Dunn <eddie.dunn@gmail.com> Tested-by: Jakub Luzny <limoto94@gmail.com> Tested-by: Olivier Goffart <olivier@woboq.com> Signed-off-by: Tai-hwa Liang <avatar@sentelic.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
As the initial domain we are able to search/map certain regions
of memory to harvest configuration data. For all low-level we
use ACPI tables - for interrupts we use exclusively ACPI _PRT
(so DSDT) and MADT for INT_SRC_OVR.
The SMP MP table is not used at all. As a matter of fact we do
not even support machines that only have SMP MP but no ACPI tables.
Lets follow how Moorestown does it and just disable searching
for BIOS SMP tables.
This also fixes an issue on HP Proliant BL680c G5 and DL380 G6:
9f->100 for 1:1 PTE
Freeing 9f-100 pfn range: 97 pages freed
1-1 mapping on 9f->100
.. snip..
e820: BIOS-provided physical RAM map:
Xen: [mem 0x0000000000000000-0x000000000009efff] usable
Xen: [mem 0x000000000009f400-0x00000000000fffff] reserved
Xen: [mem 0x0000000000100000-0x00000000cfd1dfff] usable
.. snip..
Scan for SMP in [mem 0x00000000-0x000003ff]
Scan for SMP in [mem 0x0009fc00-0x0009ffff]
Scan for SMP in [mem 0x000f0000-0x000fffff]
found SMP MP-table at [mem 0x000f4fa0-0x000f4faf] mapped at [ffff8800000f4fa0]
(XEN) mm.c:908:d0 Error getting mfn 100 (pfn 5555555555555555) from L1 entry 0000000000100461 for l1e_owner=0, pg_owner=0
(XEN) mm.c:4995:d0 ptwr_emulate: could not get_page_from_l1e()
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81ac07e2>] xen_set_pte_init+0x66/0x71
. snip..
Pid: 0, comm: swapper Not tainted 3.6.0-rc6upstream-00188-gb6fb969-dirty #2 HP ProLiant BL680c G5
.. snip..
Call Trace:
[<ffffffff81ad31c6>] __early_ioremap+0x18a/0x248
[<ffffffff81624731>] ? printk+0x48/0x4a
[<ffffffff81ad32ac>] early_ioremap+0x13/0x15
[<ffffffff81acc140>] get_mpc_size+0x2f/0x67
[<ffffffff81acc284>] smp_scan_config+0x10c/0x136
[<ffffffff81acc2e4>] default_find_smp_config+0x36/0x5a
[<ffffffff81ac3085>] setup_arch+0x5b3/0xb5b
[<ffffffff81624731>] ? printk+0x48/0x4a
[<ffffffff81abca7f>] start_kernel+0x90/0x390
[<ffffffff81abc356>] x86_64_start_reservations+0x131/0x136
[<ffffffff81abfa83>] xen_start_kernel+0x65f/0x661
(XEN) Domain 0 crashed: 'noreboot' set - not rebooting.
which is that ioremap would end up mapping 0xff using _PAGE_IOMAP
(which is what early_ioremap sticks as a flag) - which meant
we would get MFN 0xFF (pte ff461, which is OK), and then it would
also map 0x100 (b/c ioremap tries to get page aligned request, and
it was trying to map 0xf4fa0 + PAGE_SIZE - so it mapped the next page)
as _PAGE_IOMAP. Since 0x100 is actually a RAM page, and the _PAGE_IOMAP
bypasses the P2M lookup we would happily set the PTE to 1000461.
Xen would deny the request since we do not have access to the
Machine Frame Number (MFN) of 0x100. The P2M[0x100] is for example
0x80140.
CC: stable@vger.kernel.org
Fixes-Oracle-Bugzilla: https://bugzilla.oracle.com/bugzilla/show_bug.cgi?id=13665 Acked-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A small collection of driver fixes/updates and a core fix for 3.6. It
contains:
- Bug fixes for mtip32xx, and support for new hardware (just addition
of IDs). They have been queued up for 3.7 for a few weeks as well.
- rate-limit a failing command error message in block core.
- A fix for an old cciss bug from Stephen.
- Prevent overflow of partition count from Alan."
* 'for-linus' of git://git.kernel.dk/linux-block:
cciss: fix handling of protocol error
blk: add an upper sanity check on partition adding
mtip32xx: fix user_buffer check in exec_drive_command
mtip32xx: Remove dead code
mtip32xx: Change printk to pr_xxxx
mtip32xx: Proper reporting of write protect status on big-endian
mtip32xx: Increase timeout for standby command
mtip32xx: Handle NCQ commands during the security locked state
mtip32xx: Add support for new devices
block: rate-limit the error message from failing commands
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: Fix up TIF_NOTIFY_RESUME sans TIF_SIGPENDING handling.
sh: pfc: Release spinlock in sh_pfc_gpio_request_enable() error path
sh: intc: Fix up multi-evt irq association.
Merge tag 'md-3.6-fixes' of git://neil.brown.name/md
Pull md fixes from NeilBrown:
"3 fixes for md in 3.6.
One reverts a recent patch which turns out to not be such a good idea.
Other two fix minor bugs with the new (since 3.3) 'replacement' code
and have been tagged for -stable."
* tag 'md-3.6-fixes' of git://neil.brown.name/md:
md: make sure metadata is updated when spares are activated or removed.
md/raid5: fix calculate of 'degraded' when a replacement becomes active.
Revert "md/raid5: For odirect-write performance, do not set STRIPE_PREREAD_ACTIVE."
Merge branch 'for-3.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue / powernow-k8 fix from Tejun Heo:
"This is the fix for the bug where cpufreq/powernow-k8 was tripping
BUG_ON() in try_to_wake_up_local() by migrating workqueue worker to a
different CPU.
https://bugzilla.kernel.org/show_bug.cgi?id=47301
As discussed, the fix is now two parts - one to reimplement
work_on_cpu() so that it doesn't create a new kthread each time and
the actual fix which makes powernow-k8 use work_on_cpu() instead of
performing manual migration.
While pretty late in the merge cycle, both changes are on the safer
side. Jiri and I verified two existing users of work_on_cpu() and
Duncan confirmed that the powernow-k8 fix survived about 18 hours of
testing."
* 'for-3.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
cpufreq/powernow-k8: workqueue user shouldn't migrate the kworker to another CPU
workqueue: reimplement work_on_cpu() using system_wq
There was a plan to place ab8500_irq_get_virq() calls in each AB8500
child device prior to requesting an IRQ, but as we're no longer using
Device Tree to collect our IRQ numbers, it's actually better to allow
the core to do this during device registration time. So the IRQ number
we pull from its resource has already been converted to a virtual IRQ.
Signed-off-by: Lee Jones <lee.jones@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
cpufreq/powernow-k8: workqueue user shouldn't migrate the kworker to another CPU
powernowk8_target() runs off a per-cpu work item and if the
cpufreq_policy->cpu is different from the current one, it migrates the
kworker to the target CPU by manipulating current->cpus_allowed. The
function migrates the kworker back to the original CPU but this is
still broken. Workqueue concurrency management requires the kworkers
to stay on the same CPU and powernowk8_target() ends up triggerring
BUG_ON(rq != this_rq()) in try_to_wake_up_local() if it contends on
fidvid_mutex and sleeps.
It is unclear why this bug is being reported now. Duncan says it
appeared to be a regression of 3.6-rc1 and couldn't reproduce it on
3.5. Bisection seemed to point to 63d95a91 "workqueue: use @pool
instead of @gcwq or @cpu where applicable" which is an non-functional
change. Given that the reproduce case sometimes took upto days to
trigger, it's easy to be misled while bisecting. Maybe something made
contention on fidvid_mutex more likely? I don't know.
This patch fixes the bug by using work_on_cpu() instead if @pol->cpu
isn't the same as the current one. The code assumes that
cpufreq_policy->cpu is kept online by the caller, which Rafael tells
me is the case.
stable: ed48ece27c ("workqueue: reimplement work_on_cpu() using
system_wq") should be applied before this; otherwise, the
behavior could be horrible.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Duncan <1i5t5.duncan@cox.net> Tested-by: Duncan <1i5t5.duncan@cox.net> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Andreas Herrmann <andreas.herrmann3@amd.com> Cc: stable@vger.kernel.org
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47301
workqueue: reimplement work_on_cpu() using system_wq
The existing work_on_cpu() implementation is hugely inefficient. It
creates a new kthread, execute that single function and then let the
kthread die on each invocation.
Now that system_wq can handle concurrent executions, there's no
advantage of doing this. Reimplement work_on_cpu() using system_wq
which makes it simpler and way more efficient.
stable: While this isn't a fix in itself, it's needed to fix a
workqueue related bug in cpufreq/powernow-k8. AFAICS, this
shouldn't break other existing users.
Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Jiri Kosina <jkosina@suse.cz> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Len Brown <lenb@kernel.org> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: stable@vger.kernel.org
This patch updates the existing Intel IvyBridge (model 58)
support with proper PEBS event constraints. It cannot reuse
the same as SandyBridge because some events (0xd3) are
specific to IvyBridge.
Also there is no UOPS_DISPATCHED.THREAD on IVB, so do not
populate the PERF_COUNT_HW_STALLED_CYCLES_BACKEND mapping.
linux/kernel.h: Fix warning seen with W=1 due to change in DIV_ROUND_CLOSEST
After commit b6d86d3d (Fix DIV_ROUND_CLOSEST to support negative dividends),
the following warning is seen if the kernel is compiled with W=1 (-Wextra):
warning: comparison of unsigned expression >= 0 is always true
The warning is due to the test '((typeof(x))-1) >= 0', which is used to detect
if the variable type is unsigned. Research on the web suggests that the warning
disappears if '>' instead of '>=' is used for the comparison.
Tests after changing the macro along that line show that the warning is gone,
and that the result is still correct:
md: make sure metadata is updated when spares are activated or removed.
It isn't always necessary to update the metadata when spares are
removed as the presence-or-not of a spare isn't really important to
the integrity of an array.
Also activating a spare doesn't always require updating the metadata
as the update on 'recovery-completed' is usually sufficient.
However the introduction of 'replacement' devices have made these
transitions sometimes more important. For example the 'Replacement'
flag isn't cleared until the original device is removed, so we need
to ensure a metadata update after that 'spare' is removed.
So set MD_CHANGE_DEVS whenever a spare is activated or removed, to
complement the current situation where it is set when a spare is added
or a device is failed (or a number of other less common situations).
This is suitable for -stable as out-of-data metadata could lead
to data corruption.
This is only relevant for 3.3 and later 9when 'replacement' as
introduced.
md/raid5: fix calculate of 'degraded' when a replacement becomes active.
When a replacement device becomes active, we mark the device that it
replaces as 'faulty' so that it can subsequently get removed.
However 'calc_degraded' only pays attention to the primary device, not
the replacement, so the array appears to become degraded, which is
wrong.
So teach 'calc_degraded' to consider any replacement if a primary
device is faulty.
This is suitable for -stable as an incorrect 'degraded' value can
confuse md and could lead to data corruption.
This is only relevant for 3.3 and later.
Cc: stable@vger.kernel.org Reported-by: Robin Hill <robin@robinhill.me.uk> Reported-by: John Drescher <drescherjm@gmail.com> Signed-off-by: NeilBrown <neilb@suse.de>
While this patch seemed like a good idea and did help some workloads,
it hurts other workloads.
Large sequential O_DIRECT writes were faster,
Small random O_DIRECT writes were slower.
Other changes (batching RAID5 writes) have improved the sequential
writes using a different mechanism, so the net result of this patch
is definitely negative. So revert it.
Reported-by: Shaohua Li <shli@kernel.org> Tested-by: Jianpeng Ma <majianpeng@gmail.com> Signed-off-by: NeilBrown <neilb@suse.de>
A heavy-load test on a MacBookPro6,1 is still showing a substantial
amount of read errors. Increasing the maximum wait time to 128 ms
resolves the issue.
vfs: dcache: use DCACHE_DENTRY_KILLED instead of DCACHE_DISCONNECTED in d_kill()
IBM reported a soft lockup after applying the fix for the rename_lock
deadlock. Commit c83ce989cb5f ("VFS: Fix the nfs sillyrename regression
in kernel 2.6.38") was found to be the culprit.
The nfs sillyrename fix used DCACHE_DISCONNECTED to indicate that the
dentry was killed. This flag can be set on non-killed dentries too,
which results in infinite retries when trying to traverse the dentry
tree.
This patch introduces a separate flag: DCACHE_DENTRY_KILLED, which is
only set in d_kill() and makes try_to_ascend() test only this flag.
IBM reported successful test results with this patch.
Olof Johansson [Tue, 18 Sep 2012 17:16:44 +0000 (10:16 -0700)]
Merge tag 'imx-fixes' of git://git.pengutronix.de/git/imx/linux-2.6 into fixes
From Sascha Hauer:
ARM i.MX: Two fixes for i.MX
- armadillo5x0 board broken since v3.5 (stable material)
- i.MX25 Architecture broken since v3.6-rc1
* tag 'imx-fixes' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM i.MX25: Make timer irq work again
ARM: imx: armadillo5x0: Fix illegal register access
Since i.MX has SPARSE_IRQ enabled the i.MX25 timer is broken. This
is because the internal irqs now start at an offset of NR_IRQS_LEGACY.
The patch fixed this up, but missed the i.MX25 timer which used a
hardcoded value instead of a define. This patch introduces a define
for the timer irq and uses it.
Olof Johansson [Tue, 18 Sep 2012 14:40:02 +0000 (07:40 -0700)]
Merge branch 'v3.6-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
* 'v3.6-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: Use spin_lock_{irqsave,irqrestore} in clk_set_rate
ARM: SAMSUNG: use spin_lock_irqsave() in clk_set_parent
If a command completes with a status of CMD_PROTOCOL_ERR, this
information should be conveyed to the SCSI mid layer, not dropped
on the floor. Unlike a similar bug in the hpsa driver, this bug
only affects tape drives and CD and DVD ROM drives in the cciss
driver, and to induce it, you have to disconnect (or damage) a
cable, so it is not a very likely scenario (which would explain
why the bug has gone undetected for the last 10 years.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Cc: stable@vger.kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk>
Al Viro [Tue, 18 Sep 2012 08:04:37 +0000 (17:04 +0900)]
sh: Fix up TIF_NOTIFY_RESUME sans TIF_SIGPENDING handling.
As Al notes, we missed a TIF_NOTIFY_RESUME check which caused any
handlers without TIF_SIGPENDING also set to skip the notification:
Looks like while it is in the relevant masks *and* checked in
do_notify_resume() both on 32bit and 64bit variants since commit ab99c733ae73cce31f2a2434f7099564e5a73d95 ("sh: Make syscall tracer
use tracehook notifiers, add TIF_NOTIFY_RESUME.") they are
actually *not* reached without simulataneous SIGPENDING, since
the actual glue in the callers had not been updated back then and
still checks for _TIF_SIGPENDING alone when deciding whether to
hit do_notify_resume() or not.
Reported-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Tested-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh: pfc: Release spinlock in sh_pfc_gpio_request_enable() error path
The sh_pfc_gpio_request_enable() function acquires a spinlock but fails
to release it before returning if the requested mux type is not
supported. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Tushar Behera [Tue, 18 Sep 2012 01:05:34 +0000 (10:05 +0900)]
ARM: SAMSUNG: Use spin_lock_{irqsave,irqrestore} in clk_set_rate
The spinlock clocks_lock can be held during ISR, hence it is not safe to
hold that lock with disabling interrupts.
It fixes following potential deadlock.
=========================================================
[ INFO: possible irq lock inversion dependency detected ]
3.6.0-rc4+ #2 Not tainted
---------------------------------------------------------
swapper/0/1 just changed the state of lock:
(&(&host->lock)->rlock){-.....}, at: [<c027fb0d>] sdhci_irq+0x15/0x564
but this lock took another, HARDIRQ-unsafe lock in the past:
(clocks_lock){+.+...}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
Merge branch 'for-3.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull another workqueue fix from Tejun Heo:
"Unfortunately, yet another late fix. This too is discovered and fixed
by Lai. This bug was introduced during this merge window by commit 25511a477657 ("workqueue: reimplement CPU online rebinding to handle
idle workers") which started using WORKER_REBIND flag for idle rebind
too.
The bug is relatively easy to trigger if the CPU rapidly goes through
off, on and then off (and stay off). The fix is on the safer side.
This hasn't been on linux-next yet but I'm pushing early so that it
can get more exposure before v3.6 release."
* 'for-3.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: always clear WORKER_REBIND in busy_worker_rebind_fn()
Lai Jiangshan [Mon, 17 Sep 2012 22:42:31 +0000 (15:42 -0700)]
workqueue: always clear WORKER_REBIND in busy_worker_rebind_fn()
busy_worker_rebind_fn() didn't clear WORKER_REBIND if rebinding failed
(CPU is down again). This used to be okay because the flag wasn't
used for anything else.
However, after 25511a477 "workqueue: reimplement CPU online rebinding
to handle idle workers", WORKER_REBIND is also used to command idle
workers to rebind. If not cleared, the worker may confuse the next
CPU_UP cycle by having REBIND spuriously set or oops / get stuck by
prematurely calling idle_worker_rebind().
There was no reason to keep WORKER_REBIND on failure in the first
place - WORKER_UNBOUND is guaranteed to be set in such cases
preventing incorrectly activating concurrency management. Always
clear WORKER_REBIND.
tj: Updated comment and description.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by: Tejun Heo <tj@kernel.org>
Merge fixes from Andrew Morton:
"13 patches. 12 are fixes and one is a little preparatory thing for
Andi."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (13 commits)
memory hotplug: fix section info double registration bug
mm/page_alloc: fix the page address of higher page's buddy calculation
drivers/rtc/rtc-twl.c: ensure all interrupts are disabled during probe
compiler.h: add __visible
pid-namespace: limit value of ns_last_pid to (0, max_pid)
include/net/sock.h: squelch compiler warning in sk_rmem_schedule()
slub: consider pfmemalloc_match() in get_partial_node()
slab: fix starting index for finding another object
slab: do ClearSlabPfmemalloc() for all pages of slab
nbd: clear waiting_queue on shutdown
MAINTAINERS: fix TXT maintainer list and source repo path
mm/ia64: fix a memory block size bug
memory hotplug: reset pgdat->kswapd to NULL if creating kernel thread fails
memory hotplug: fix section info double registration bug
There may be a bug when registering section info. For example, on my
Itanium platform, the pfn range of node0 includes the other nodes, so
other nodes' section info will be double registered, and memmap's page
count will equal to 3.
Li Haifeng [Mon, 17 Sep 2012 21:09:21 +0000 (14:09 -0700)]
mm/page_alloc: fix the page address of higher page's buddy calculation
The heuristic method for buddy has been introduced since commit 43506fad21ca ("mm/page_alloc.c: simplify calculation of combined index
of adjacent buddy lists"). But the page address of higher page's buddy
was wrongly calculated, which will lead page_is_buddy to fail for ever.
IOW, the heuristic method would be disabled with the wrong page address
of higher page's buddy.
Calculating the page address of higher page's buddy should be based
higher_page with the offset between index of higher page and index of
higher page's buddy.
Signed-off-by: Haifeng Li <omycle@gmail.com> Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Reviewed-by: Michal Hocko <mhocko@suse.cz> Cc: KyongHo Cho <pullip.cho@samsung.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Minchan Kim <minchan.kim@gmail.com> Cc: Johannes Weiner <jweiner@redhat.com> Cc: <stable@vger.kernel.org> [2.6.38+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kevin Hilman [Mon, 17 Sep 2012 21:09:17 +0000 (14:09 -0700)]
drivers/rtc/rtc-twl.c: ensure all interrupts are disabled during probe
On some platforms, bootloaders are known to do some interesting RTC
programming. Without going into the obscurities as to why this may be
the case, suffice it to say the the driver should not make any
assumptions about the state of the RTC when the driver loads. In
particular, the driver probe should be sure that all interrupts are
disabled until otherwise programmed.
This was discovered when finding bursty I2C traffic every second on
Overo platforms. This I2C overhead was keeping the SoC from hitting
deep power states. The cause was found to be the RTC firing every
second on the I2C-connected TWL PMIC.
Special thanks to Felipe Balbi for suggesting to look for a rogue driver
as the source of the I2C traffic rather than the I2C driver itself.
Special thanks to Steve Sakoman for helping track down the source of the
continuous RTC interrups on the Overo boards.
Signed-off-by: Kevin Hilman <khilman@ti.com> Cc: Felipe Balbi <balbi@ti.com> Tested-by: Steve Sakoman <steve@sakoman.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Tested-by: Shubhrajyoti Datta <omaplinuxkernel@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcc 4.6+ has support for a externally_visible attribute that prevents the
optimizer from optimizing unused symbols away. Add a __visible macro to
use it with that compiler version or later.
This is used (at least) by the "Link Time Optimization" patchset.
Chuck Lever [Mon, 17 Sep 2012 21:09:11 +0000 (14:09 -0700)]
include/net/sock.h: squelch compiler warning in sk_rmem_schedule()
This warning:
In file included from linux/include/linux/tcp.h:227:0,
from linux/include/linux/ipv6.h:221,
from linux/include/net/ipv6.h:16,
from linux/include/linux/sunrpc/clnt.h:26,
from linux/net/sunrpc/stats.c:22:
linux/include/net/sock.h: In function `sk_rmem_schedule':
linux/nfs-2.6/include/net/sock.h:1339:13: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
is seen with gcc (GCC) 4.6.3 20120306 (Red Hat 4.6.3-2) using the
-Wextra option.
Commit c76562b6709f ("netvm: prevent a stream-specific deadlock")
accidentally replaced the "size" parameter of sk_rmem_schedule() with an
unsigned int. This changes the semantics of the comparison in the
return statement.
In sk_wmem_schedule we have syntactically the same comparison, but
"size" is a signed integer. In addition, __sk_mem_schedule() takes a
signed integer for its "size" parameter, so there is an implicit type
conversion in sk_rmem_schedule() anyway.
Revert the "size" parameter back to a signed integer so that the
semantics of the expressions in both sk_[rw]mem_schedule() are exactly
the same.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Mel Gorman <mgorman@suse.de> Cc: David Miller <davem@davemloft.net> Cc: Joonsoo Kim <js1304@gmail.com> Cc: David Rientjes <rientjes@google.com> Cc: Pekka Enberg <penberg@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joonsoo Kim [Mon, 17 Sep 2012 21:09:09 +0000 (14:09 -0700)]
slub: consider pfmemalloc_match() in get_partial_node()
get_partial() is currently not checking pfmemalloc_match() meaning that
it is possible for pfmemalloc pages to leak to non-pfmemalloc users.
This is a problem in the following situation. Assume that there is a
request from normal allocation and there are no objects in the per-cpu
cache and no node-partial slab.
In this case, slab_alloc enters the slow path and new_slab_objects() is
called which may return a PFMEMALLOC page. As the current user is not
allowed to access PFMEMALLOC page, deactivate_slab() is called
([5091b74a: mm: slub: optimise the SLUB fast path to avoid pfmemalloc
checks]) and returns an object from PFMEMALLOC page.
Next time, when we get another request from normal allocation,
slab_alloc() enters the slow-path and calls new_slab_objects(). In
new_slab_objects(), we call get_partial() and get a partial slab which
was just deactivated but is a pfmemalloc page. We extract one object
from it and re-deactivate.
"deactivate -> re-get in get_partial -> re-deactivate" occures repeatedly.
As a result, access to PFMEMALLOC page is not properly restricted and it
can cause a performance degradation due to frequent deactivation.
deactivation frequently.
This patch changes get_partial_node() to take pfmemalloc_match() into
account and prevents the "deactivate -> re-get in get_partial()
scenario. Instead, new_slab() is called.
Signed-off-by: Joonsoo Kim <js1304@gmail.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Mel Gorman <mgorman@suse.de> Cc: David Miller <davem@davemloft.net> Cc: Chuck Lever <chuck.lever@oracle.com> Cc: Pekka Enberg <penberg@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joonsoo Kim [Mon, 17 Sep 2012 21:09:06 +0000 (14:09 -0700)]
slab: fix starting index for finding another object
In array cache, there is a object at index 0, check it.
Signed-off-by: Joonsoo Kim <js1304@gmail.com> Signed-off-by: Mel Gorman <mgorman@suse.de> Cc: David Miller <davem@davemloft.net> Cc: Chuck Lever <chuck.lever@oracle.com> Cc: David Rientjes <rientjes@google.com> Cc: Pekka Enberg <penberg@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
slab: do ClearSlabPfmemalloc() for all pages of slab
Right now, we call ClearSlabPfmemalloc() for first page of slab when we
clear SlabPfmemalloc flag. This is fine for most swap-over-network use
cases as it is expected that order-0 pages are in use. Unfortunately it
is possible that that __ac_put_obj() checks SlabPfmemalloc on a tail
page and while this is harmless, it is sloppy. This patch ensures that
the head page is always used.
This problem was originally identified by Joonsoo Kim.
[js1304@gmail.com: Original implementation and problem identification] Signed-off-by: Mel Gorman <mgorman@suse.de> Cc: David Miller <davem@davemloft.net> Cc: Chuck Lever <chuck.lever@oracle.com> Cc: Joonsoo Kim <js1304@gmail.com> Cc: David Rientjes <rientjes@google.com> Cc: Pekka Enberg <penberg@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Clements [Mon, 17 Sep 2012 21:09:02 +0000 (14:09 -0700)]
nbd: clear waiting_queue on shutdown
Fix a serious but uncommon bug in nbd which occurs when there is heavy
I/O going to the nbd device while, at the same time, a failure (server,
network) or manual disconnect of the nbd connection occurs.
There is a small window between the time that the nbd_thread is stopped
and the socket is shutdown where requests can continue to be queued to
nbd's internal waiting_queue. When this happens, those requests are
never completed or freed.
The fix is to clear the waiting_queue on shutdown of the nbd device, in
the same way that the nbd request queue (queue_head) is already being
cleared.
Signed-off-by: Paul Clements <paul.clements@steeleye.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gang Wei [Mon, 17 Sep 2012 21:08:59 +0000 (14:08 -0700)]
MAINTAINERS: fix TXT maintainer list and source repo path
Signed-off-by: Gang Wei <gang.wei@intel.com> Cc: Richard L Maliszewski <richard.l.maliszewski@intel.com> Cc: Gang Wei <gang.wei@intel.com> Cc: Shane Wang <shane.wang@intel.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because MIN_MEMORY_BLOCK_SIZE is int type and length of 32bits,
so MIN_MEMORY_BLOCK_SIZE(1 << 32) will will equal to 0.
Actually when SECTION_SIZE_BITS >= 31, MIN_MEMORY_BLOCK_SIZE will be wrong.
This will cause wrong system memory infomation in sysfs.
I think it should be:
And "echo offline > memory0/state" will cause following call trace:
kernel BUG at mm/memory_hotplug.c:885!
sh[6455]: bugcheck! 0 [1]
Pid: 6455, CPU 0, comm: sh
psr : 0000101008526030 ifs : 8000000000000fa4 ip : [<a0000001008c40f0>] Not tainted (3.6.0-rc1)
ip is at offline_pages+0x210/0xee0
Call Trace:
show_stack+0x80/0xa0
show_regs+0x640/0x920
die+0x190/0x2c0
die_if_kernel+0x50/0x80
ia64_bad_break+0x3d0/0x6e0
ia64_native_leave_kernel+0x0/0x270
offline_pages+0x210/0xee0
alloc_pages_current+0x180/0x2a0
Signed-off-by: Jianguo Wu <wujianguo@huawei.com> Signed-off-by: Jiang Liu <jiang.liu@huawei.com> Cc: "Luck, Tony" <tony.luck@intel.com> Reviewed-by: Michal Hocko <mhocko@suse.cz> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
memory hotplug: reset pgdat->kswapd to NULL if creating kernel thread fails
If kthread_run() fails, pgdat->kswapd contains errno. When we stop this
thread, we only check whether pgdat->kswapd is NULL and access it. If
it contains errno, it will cause page fault. Reset pgdat->kswapd to
NULL when creating kernel thread fails can avoid this problem.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com> Reviewed-by: Minchan Kim <minchan@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 'name' sysfs attribute is mandatory for hwmon devices, but was missing
in this driver.
Cc: Paul Thomas <pthomas8589@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Jean Delvare <khali@linux-fr.org> Acked-by: Paul Thomas <pthomas8589@gmail.com>
This commit fixed certain cases, but ended up regressing others
due to limitations in the current KMS API. A proper fix is too
invasive for 3.6. Push it back to 3.7.
Reported-by: Andres Freund <andres@anarazel.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA fixes from Roland Dreier:
- A couple more IPoIB fixes for regressions introduced by path database
conversion
- Minor other fixes to low-level drivers (cxgb4, mlx4, qib, ocrdma)
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/qib: Fix failure of compliance test C14-024#06_LocalPortNum
RDMA/ocrdma: Fix CQE expansion of unsignaled WQE
mlx4_core: Fix integer overflows so 8TBs of memory registration works
IPoIB: Fix AB-BA deadlock when deleting neighbours
IPoIB: Fix memory leak in the neigh table deletion flow
RDMA/cxgb4: Move dereference below NULL test
fs/proc: fix potential unregister_sysctl_table hang
The unregister_sysctl_table() function hangs if all references to its
ctl_table_header structure are not dropped.
This can happen sometimes because of a leak in proc_sys_lookup():
proc_sys_lookup() gets a reference to the table via lookup_entry(), but
it does not release it when a subsequent call to sysctl_follow_link()
fails.
This patch fixes this leak by making sure the reference is always
dropped on return.
See also commit 076c3eed2c31 ("sysctl: Rewrite proc_sys_lookup
introducing find_entry and lookup_entry") which reorganized this code in
3.4.
Tested in Linux 3.4.4.
Signed-off-by: Francesco Ruggeri <fruggeri@aristanetworks.com> Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wang Xingchao [Wed, 12 Sep 2012 23:43:22 +0000 (07:43 +0800)]
drm/i915: HDMI - Clear Audio Enable bit for Hot Plug
Clear Audio Enable bit to trigger unsolicated event to notify Audio
Driver part the HDMI hot plug change. The patch fixed the bug when
remove HDMI cable the bit was not cleared correctly.
In intel_hdmi_dpms(), if intel_hdmi->has_audio been true, the "Audio enable bit" will
be set to trigger unsolicated event to notify Alsa driver the change.
intel_hdmi->has_audio will be reset to false from intel_hdmi_detect() after
remove the hdmi cable, here's debug log:
[ 187.494153] [drm:output_poll_execute], [CONNECTOR:17:HDMI-A-1] status updated from 1 to 2
[ 187.525349] [drm:intel_hdmi_detect], HDMI: has_audio = 0
so when comes back to intel_hdmi_dpms(), the "Audio enable bit" will not be cleared. And this
cause the eld infomation and pin presence doesnot update accordingly in alsa driver side.
This patch will also trigger unsolicated event to alsa driver to notify the hot plug event:
Chris Wilson [Sat, 15 Sep 2012 08:41:57 +0000 (09:41 +0100)]
drm/i915: Reduce a pin-leak BUG into a WARN
Pin-leaks persist and we get the perennial bug reports of machine
lockups to the BUG_ON(pin_count==MAX). If we instead loudly report that
the object cannot be pinned at that time it should prevent the driver from
locking up, and hopefully restore a semblance of working whilst still
leaving us a OOPS to debug.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: stable@vger.kernel.org Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Stefan Haberland [Tue, 11 Sep 2012 15:19:12 +0000 (17:19 +0200)]
s390/dasd: fix read unit address configuration loop
Read unit address is done for all devices during online processing to read
out LCU features. This is also done after disconnect/connect a LCU.
Some older storage hardware does not provide the capability to read unit
address configuration.
This leads to a loop trying to read unit address configuration every 30
seconds. The device is still operational but logs are flooded with error
messages.
Fix the loop by recognizing a command reject saying that the suborder
for ruac is not supported.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Stefan Haberland [Tue, 11 Sep 2012 13:10:58 +0000 (15:10 +0200)]
s390/dasd: fix pathgroup race
If a new path is available we need to verify the path data. If it is the
first path for a device the stop bits are removed after path verification.
If a pathgroup is established we need to set system characteristics for
the lcu. Therefore I/O has to be started.
If the device is stopped the set system characteristics worker may block
the path verification worker and the device is blocked.
Turn on failfast for set system characteristics CQR to prevent a deadlock
with the path verification worker.
If a pathgroup is established on a device that is not in use trigger path
verification. Maybe we were not informed about a working path.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com> Reviewed-by: Stefan Weinhuber <wein@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The s390 page-table walk code, used for user copy and futex, currently
cannot handle huge pages. As far as user copy is concerned, that is
not really a problem because those functions will only be used on old
hardware that has no huge page support. But the futex code will also
use pagetable walk functions on current hardware when user space runs
in primary space mode. So, if a futex sits in a huge page, the futex
operation on it will result in a page fault loop or even data
corruption.
This patch adds the code for resolving huge page mappings in the user
access pagetable walk code on s390.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
ARM: SAMSUNG: use spin_lock_irqsave() in clk_set_parent
From 0cdf3aff, "ARM: SAMSUNG: use spin_lock_irqsave() in
clk_{enable,disable}":
The clk_enable()and clk_disable() can be used process and ISR either.
And actually it is used for real product and other platforms use it
now. So spin_lock_irqsave() should be used instead.
We need to make a similar change in clk_set_parent(). Otherwise,
you can potentially get spinlock recursion:
BUG: spinlock recursion on CPU#0, kinteractive/68
lock: 807832a8, .magic: dead4ead, .owner: kinteractive/68, .owner_cpu: 0
[<80015f54>] (unwind_backtrace+0x0/0x128) from [<804f2914>] (dump_stack+0x20/0x24)
[<804f2914>] (dump_stack+0x20/0x24) from [<804f57b8>] (spin_dump+0x80/0x94)
[<804f57b8>] (spin_dump+0x80/0x94) from [<804f57f8>] (spin_bug+0x2c/0x30)
[<804f57f8>] (spin_bug+0x2c/0x30) from [<80222730>] (do_raw_spin_lock+0x54/0x150)
[<80222730>] (do_raw_spin_lock+0x54/0x150) from [<804f96ec>] (_raw_spin_lock_irqsave+0x20/0x28)
[<804f96ec>] (_raw_spin_lock_irqsave+0x20/0x28) from [<80022ea4>] (clk_enable+0x3c/0x84)
[<80022ea4>] (clk_enable+0x3c/0x84) from [<8038336c>] (s5p_mfc_clock_on+0x60/0x74)
[<8038336c>] (s5p_mfc_clock_on+0x60/0x74) from [<8038645c>] (s5p_mfc_read_info+0x20/0x38)
[<8038645c>] (s5p_mfc_read_info+0x20/0x38) from [<8037ca3c>] (s5p_mfc_handle_frame+0x2e4/0x4bc)
[<8037ca3c>] (s5p_mfc_handle_frame+0x2e4/0x4bc) from [<8037d420>] (s5p_mfc_irq+0x1ec/0x6cc)
[<8037d420>] (s5p_mfc_irq+0x1ec/0x6cc) from [<8007fc74>] (handle_irq_event_percpu+0x8c/0x244)
[<8007fc74>] (handle_irq_event_percpu+0x8c/0x244) from [<8007fe78>] (handle_irq_event+0x4c/0x6c)
[<8007fe78>] (handle_irq_event+0x4c/0x6c) from [<80082dd8>] (handle_fasteoi_irq+0xe4/0x150)
[<80082dd8>] (handle_fasteoi_irq+0xe4/0x150) from [<8007f424>] (generic_handle_irq+0x3c/0x50)
[<8007f424>] (generic_handle_irq+0x3c/0x50) from [<8000f7c4>] (handle_IRQ+0x88/0xc8)
[<8000f7c4>] (handle_IRQ+0x88/0xc8) from [<80008564>] (gic_handle_irq+0x44/0x68)
[<80008564>] (gic_handle_irq+0x44/0x68) from [<8000e400>] (__irq_svc+0x40/0x60)
Exception stack(0xef3cbe68 to 0xef3cbeb0)
[<8000e400>] (__irq_svc+0x40/0x60) from [<80022cfc>] (clk_set_parent+0x30/0x74)
[<80022cfc>] (clk_set_parent+0x30/0x74) from [<803ac7f8>] (set_apll.isra.0+0x28/0xb0)
[<803ac7f8>] (set_apll.isra.0+0x28/0xb0) from [<803ac8e4>] (exynos5250_set_frequency+0x64/0xb8)
[<803ac8e4>] (exynos5250_set_frequency+0x64/0xb8) from [<803ac280>] (exynos_target+0x1b0/0x220)
[<803ac280>] (exynos_target+0x1b0/0x220) from [<803a4a0c>] (__cpufreq_driver_target+0xb0/0xd4)
[<803a4a0c>] (__cpufreq_driver_target+0xb0/0xd4) from [<803aab80>] (cpufreq_interactive_updown_task+0x214/0x264)
[<803aab80>] (cpufreq_interactive_updown_task+0x214/0x264) from [<80047d04>] (kthread+0x9c/0xa8)
[<80047d04>] (kthread+0x9c/0xa8) from [<8000fa48>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Mandeep Singh Baines <msb@chromium.org> Suggested-by: Sunil Mazhavanchery <sunilm@samsung.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-samsung-soc@vger.kernel.org Cc: Ben Dooks <ben-linux@fluff.org> Cc: Russell King <linux@arm.linux.org.uk> Cc: Minho Ban <mhban@samsung.com> Cc: Jaecheol Lee <jc.lee@samsung.com> Cc: Sunyoung Kang <sy0816.kang@samsung.com> Cc: Olof Johansson <olofj@chromium.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Merge tag 'mfd-for-linus-3.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull mfd fixes from Samuel Ortiz:
"This is the remaining MFD fixes for 3.6, with 5 pending fixes:
- A tps65217 build error fix.
- A lcp_ich regression fix caused by the MFD driver failing to
initialize the watchdog sub device due to ACPI conflicts.
- 2 MAX77693 interrupt handling bug fixes.
- An MFD core fix, adding an IRQ domain argument to the MFD device
addition API in order to prevent silent and potentially harmful
remapping behaviour changes for drivers supporting non-DT
platforms."
* tag 'mfd-for-linus-3.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: MAX77693: Fix NULL pointer error when initializing irqs
mfd: MAX77693: Fix interrupt handling bug
mfd: core: Push irqdomain mapping out into devices
mfd: lpc_ich: Fix a 3.5 kernel regression for iTCO_wdt driver
mfd: Move tps65217 regulator plat data handling to regulator
Merge tag 'for-3.6-rc6' of git://gitorious.org/linux-pwm/linux-pwm
Pull pwm fixes from Thierry Reding:
"While this comes a bit later than I had wished, both patches are
rather minor and touch only new drivers so I think these are still
safe for merging."
* tag 'for-3.6-rc6' of git://gitorious.org/linux-pwm/linux-pwm:
pwm: pwm-tiehrpwm: Fix conflicting channel period setting
pwm: pwm-tiecap: Disable APWM mode after configure
Pull scsi target fixes from Nicholas Bellinger:
"Here is the current set of target-pending fixes headed for v3.6-final
The main parts of this series include bug-fixes from Paolo Bonzini to
address an use-after-free bug in pSCSI sense exception handling, along
with addressing some long-standing bugs wrt the handling of zero-
length SCSI CDB payloads also specific to pSCSI pass-through device
backends."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: go through normal processing for zero-length REQUEST_SENSE
target: support zero allocation length in REQUEST SENSE
target: support zero-size allocation lengths in transport_kmap_data_sg
target: fail REPORT LUNS with less than 16 bytes of payload
target: report too-small parameter lists everywhere
target: go through normal processing for zero-length PSCSI commands
target: fix use-after-free with PSCSI sense data
target: simplify code around transport_get_sense_data
target: move transport_get_sense_data
target: Check idr_get_new return value in iscsi_login_zero_tsih_s1
target: Fix ->data_length re-assignment bug with SCSI overflow
Merge tag 'pm-for-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael J. Wysocki:
"Three ACPI device power management fixes related to checking and
setting device power states."
* tag 'pm-for-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Use KERN_DEBUG when no power resources are found
ACPI / PM: Fix resource_lock dead lock in acpi_power_on_device
ACPI / PM: Infer parent power state from child if unknown, v2
Merge tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull more sound fixes from Takashi Iwai:
"Yet more (a bunch of) small fixes that slipped from the previous pull
request. Most of commits are pending ASoC fixes, all of which are
fairly trivial commits."
* tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: wm8904: correct the index
ALSA: hda - Yet another position_fix quirk for ASUS machines
ASoC: tegra: fix maxburst settings in dmaengine code
ASoC: samsung dma - Don't indicate support for pause/resume.
ASoC: mc13783: Remove mono support
ASoC: arizona: Fix typo in 44.1kHz rates
ASoC: spear: correct the check for NULL dma_buffer pointer
sound: tegra_alc5632: remove HP detect GPIO inversion
ASoC: atmel-ssc: include linux/io.h for raw io
ASoC: dapm: Don't force card bias level to be updated
ASoC: dapm: Make sure we update the bias level for CODECs with no op
ASoC: am3517evm: fix error return code
ASoC: ux500_msp_i2s: better use devm functions and fix error return code
ASoC: imx-sgtl5000: fix error return code
Nikolay Ulyanitsky reported thatthe 3.6-rc5 kernel has a 15-20%
performance drop on PostgreSQL 9.2 on his machine (running "pgbench").
Borislav Petkov was able to reproduce this, and bisected it to this
commit 970e178985ca ("sched: Improve scalability via 'CPU buddies' ...")
apparently because the new single-idle-buddy model simply doesn't find
idle CPU's to reschedule on aggressively enough.
Mike Galbraith suspects that it is likely due to the user-mode spinlocks
in PostgreSQL not reacting well to preemption, but we don't really know
the details - I'll just revert the commit for now.
There are hopefully other approaches to improve scheduler scalability
without it causing these kinds of downsides.
Reported-by: Nikolay Ulyanitsky <lystor@gmail.com> Bisected-by: Borislav Petkov <bp@alien8.de> Acked-by: Mike Galbraith <efault@gmx.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chanwoo Choi [Tue, 21 Aug 2012 06:16:23 +0000 (15:16 +0900)]
mfd: MAX77693: Fix NULL pointer error when initializing irqs
This patch initialize register map of MUIC device because mfd driver
of Maxim MAX77693 use regmap-muic instance of MUIC device when irqs of
Maxim MAX77693 is initialized before call max77693-muic probe() function.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Chanwoo Choi [Tue, 21 Aug 2012 06:15:52 +0000 (15:15 +0900)]
mfd: MAX77693: Fix interrupt handling bug
This patch fix bug related to interrupt handling for MAX77693 devices.
- Unmask interrupt masking bit for charger/flash/muic to revolve
that interrupt isn't happened when external connector is attached.
- Fix wrong regmap instance when muic interrupt is happened.
This patch were discussed and confirm discussion about this patch on below url:
http://lkml.org/lkml/2012/7/16/118
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Tue, 11 Sep 2012 07:16:36 +0000 (15:16 +0800)]
mfd: core: Push irqdomain mapping out into devices
Currently the MFD core supports remapping MFD cell interrupts using an
irqdomain but only if the MFD is being instantiated using device tree
and only if the device tree bindings use the pattern of registering IPs
in the device tree with compatible properties. This will be actively
harmful for drivers which support non-DT platforms and use this pattern
for their DT bindings as it will mean that the core will silently change
remapping behaviour and it is also limiting for drivers which don't do
DT with this particular pattern. There is also a potential fragility if
there are interrupts not associated with MFD cells and all the cells are
omitted from the device tree for some reason.
Instead change the code to take an IRQ domain as an optional argument,
allowing drivers to take the decision about the parent domain for their
interrupts. The one current user of this feature is ab8500-core, it has
the domain lookup pushed out into the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Merge tag 'asoc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for 3.6
A bigger set of updates than I'm entirely comfortable with - things
backed up a bit due to travel. As ever the majority of these are small,
focused updates for specific drivers though there are a couple of core
changes. There's been good exposure in -next.
Pull GFS2 fixes from Steven Whitehouse:
"Here are three GFS2 fixes for the current kernel tree. These are all
related to the block reservation code which was added at the merge
window. That code will be getting an update at the forthcoming merge
window too. In the mean time though there are a few smaller issues
which should be fixed.
The first patch resolves an issue with write sizes of greater than 32
bits with the size hinting code. The second ensures that the
allocation data structure is initialised when using xattrs and the
third takes into account allocations which may have been made by other
nodes which affect a reservation on the local node."
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
GFS2: Take account of blockages when using reserved blocks
GFS2: Fix missing allocation data for set/remove xattr
GFS2: Make write size hinting code common
Merge branch 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86
Pull x86 platform driver updates from Matthew Garrett:
"A few small updates for 3.6 - a trivial regression fix and a couple of
conformance updates for the gmux driver, plus some tiny fixes for
asus-wmi, eeepc-laptop and thinkpad_acpi."
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
thinkpad_acpi: buffer overflow in fan_get_status()
eeepc-laptop: fix device reference count leakage in eeepc_rfkill_hotplug()
platform/x86: fix asus_laptop.wled_type description
asus-laptop: HRWS/HWRS typo
drivers-platform-x86: remove useless #ifdef CONFIG_ACPI_VIDEO
apple-gmux: Fix port address calculation in gmux_pio_write32()
apple-gmux: Fix index read functions
apple-gmux: Obtain version info from indexed gmux
Merge branch 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux
Pull i2c embedded fixes from Wolfram Sang:
"The last bunch of (typical) i2c-embedded driver fixes for 3.6.
Also update the MAINTAINERS file to point to my tree since people keep
asking where to find their patches."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: algo: pca: Fix mode selection for PCA9665
MAINTAINERS: fix tree for current i2c-embedded development
i2c: mxs: correctly setup speed for non devicetree
i2c: pnx: Fix read transactions of >= 2 bytes
i2c: pnx: Fix bit definitions
projects / karo-tx-linux.git / log