mmc: sunxi: Add driver for SD/MMC hosts found on Allwinner sunxi SoCs
The Allwinner sunxi mmc host uses dma in bus-master mode using a built-in
designware idmac controller, which is identical to the one found in the
mmc-dw hosts. However the rest of the host is not identical to mmc-dw, it
deals with sending stop commands in hardware which makes it significantly
different from the mmc-dw devices.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
[hdegoede@redhat.com: various cleanups and fixes] Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 12:00:12 +0000 (13:00 +0100)]
mmc: sdhci: track whether preset mode is currently enabled in hardware
Track whether preset mode is currently enabled in hardware, and use that
when making decisions elsewhere in the code rather than reading the
register and checking the bit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 12:00:06 +0000 (13:00 +0100)]
mmc: sdhci: move remaining power handling into sdhci_set_power()
Move the remaining parts of the power handling in sdhci_do_set_ios()
into sdhci_set_power().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 12:00:01 +0000 (13:00 +0100)]
mmc: sdhci: move regulator handling into sdhci_set_power()
Move the regulator handling into sdhci_set_power() rather than being in
sdhci_do_set_ios(). This wraps all power control up into this function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:59:56 +0000 (12:59 +0100)]
mmc: sdhci-tegra: get rid of special PRESENT_STATE register handling
sdhci-tegra provides a get_ro method, which overrides the checking
of the write protect bit in the PRESENT_STATE register in sdhci.c:
if (host->flags & SDHCI_DEVICE_DEAD)
is_readonly = 0;
else if (host->ops->get_ro)
is_readonly = host->ops->get_ro(host);
else
is_readonly = !(sdhci_readl(host, SDHCI_PRESENT_STATE)
& SDHCI_WRITE_PROTECT);
This means it's pointless detecting accesses to this register and
manually setting the SDHCI_WRITE_PROTECT as it has no effect.
This means that the whole of tegra_sdhci_readl() can be removed and
we can use the builtin sdhci readl functionality here.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
The only user (sdhci-of-esdhc) no longer uses these callbacks, so lets
remove them to discourage any further use.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
We don't need these hooks in order to insert code in these paths, we
can just provide our own handlers and call the main sdhci handlers as
appropriate.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:59:41 +0000 (12:59 +0100)]
mmc: sdhci-esdhc-imx: remove emulation of uhs_mode
We no longer need to emulate the uhs_mode field of the host control2
register - the main sdhci driver never reads this back to evaluate
the current mode as it caches the current mode instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:59:36 +0000 (12:59 +0100)]
mmc: sdhci: clean up sdhci_execute_tuning() decision
Clean up the code in sdhci_execute_tuning() so the decision whether
to execute tuning is clearer - and despite this reflecting what the
original code was doing, it shows that it may not be what the author
actually intended.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:59:31 +0000 (12:59 +0100)]
mmc: sdhci: cache timing information locally
Rather than reading back the timing information from the registers,
cache it locally. This allows implementations to translate the UHS
timing by overriding the set_uhs_signaling() method as required
without also having to emulate the SDHCI_HOST_CONTROL2 register.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com>
[Ulf Hansson] Resolved conflict Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:59:26 +0000 (12:59 +0100)]
mmc: sdhci: convert sdhci_set_uhs_signaling() into a library function
Add sdhci_set_uhs_signaling() and always call the set_uhs_signaling
method. This avoids quirks being added into sdhci_set_uhs_signaling().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com>
[Ulf Hansson] Resolved conflict Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:59:20 +0000 (12:59 +0100)]
mmc: sdhci: set_uhs_signaling() need not return a value
The set_uhs_signaling() method gives the impression that it can fail,
but anything returned from the method is entirely ignored by the sdhci
driver. So returning failure has no effect.
So, kill the idea that it's possible for this to return an error by
removing the returned value.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2 locks held by kworker/u8:0/6:
#0: (kmmcd){.+.+.+}, at: [<c003d890>] process_one_work+0x134/0x4e8
#1: ((&(&host->detect)->work)){+.+.+.}, at: [<c003d890>] process_one_work+0x134/0x4e8
stack backtrace:
CPU: 2 PID: 6 Comm: kworker/u8:0 Not tainted 3.14.0-rc1+ #490
Workqueue: kmmcd mmc_rescan
Backtrace:
[<c00124a0>] (dump_backtrace) from [<c0012640>] (show_stack+0x18/0x1c)
[<c0012628>] (show_stack) from [<c069164c>] (dump_stack+0x70/0x8c)
[<c06915dc>] (dump_stack) from [<c068f080>] (print_usage_bug+0x274/0x2e4)
[<c068ee0c>] (print_usage_bug) from [<c0065774>] (mark_lock+0x5d4/0x6f8)
[<c00651a0>] (mark_lock) from [<c0065e6c>] (__lock_acquire+0x5d4/0x1ca0)
[<c0065898>] (__lock_acquire) from [<c0067ad8>] (lock_acquire+0xa0/0x130)
[<c0067a38>] (lock_acquire) from [<c0697a44>] (_raw_spin_lock+0x34/0x44)
[<c0697a10>] (_raw_spin_lock) from [<c04b57a4>] (esdhc_send_tuning_cmd+0x104/0x14c)
[<c04b56a0>] (esdhc_send_tuning_cmd) from [<c04b582c>] (esdhc_executing_tuning+0x40/0x100)
[<c04b57ec>] (esdhc_executing_tuning) from [<c04afa54>] (sdhci_execute_tuning+0xcc/0x754)
[<c04af988>] (sdhci_execute_tuning) from [<c04a4684>] (mmc_sd_init_card+0x65c/0x694)
[<c04a4028>] (mmc_sd_init_card) from [<c04a48f0>] (mmc_attach_sd+0xb0/0x184)
[<c04a4840>] (mmc_attach_sd) from [<c049eb28>] (mmc_rescan+0x26c/0x2e8)
[<c049e8bc>] (mmc_rescan) from [<c003d914>] (process_one_work+0x1b8/0x4e8)
[<c003d75c>] (process_one_work) from [<c003e090>] (worker_thread+0x13c/0x3f8)
[<c003df54>] (worker_thread) from [<c00449bc>] (kthread+0xcc/0xe8)
[<c00448f0>] (kthread) from [<c000e768>] (ret_from_fork+0x14/0x2c)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:59:05 +0000 (12:59 +0100)]
mmc: sdhci-esdhc-imx: comment runtime_pm_get_sync() in esdhc_prepare_tuning()
It is far from obvious what this is doing, and it looks like it's an
unbalanced runtime_pm_get() call. However, the put is inside
sdhci_tasklet_finish(), so it's not unbalanced at all. This should
be documented so people know what's going on here. Do so.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:59:00 +0000 (12:59 +0100)]
mmc: sdhci-esdhc-imx: avoid DMA to kernel stack
sdhci-esdhc-imx tries to DMA to the kernel stack when tuning the
interface, which causes dma-debug to complain. Fix this by kmallocing
a buffer to hold the received tuning pattern.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:58:55 +0000 (12:58 +0100)]
mmc: sdhci: convert sdhci_set_clock() into a library function
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:58:50 +0000 (12:58 +0100)]
mmc: sdhci: move setting mmc->actual_clock into set_clock handlers
Move the setting of mmc->actual_clock to zero into the set_clock
handlers themselves. This will allow us to clean up the calling
logic for the set_clock() method, and turn sdhci_set_clock() into
a library function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:58:45 +0000 (12:58 +0100)]
mmc: sdhci: move setting host->clock into sdhci_do_set_ios()
We don't need implementations to do this, since the only time it's
necessary is when we change the clock, and the only place that happens
is in sdhci_do_set_ios(). So, move it there, and remove it from the
iMX platform backend.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:58:40 +0000 (12:58 +0100)]
mmc: sdhci: clean up sdhci_update_clock()/sdhci_set_clock()
Only one caller to sdhci_set_clock() needs to check whether the
requested clock frequency was the same as the currently set frequency,
yet we work around this in several other sites via sdhci_update_clock().
Rather than doing this, move those checks out into sdhci_do_set_ios(),
which then allows sdhci_update_clock() to be eliminated.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:58:34 +0000 (12:58 +0100)]
mmc: sdhci: convert ADMA descriptors to a coherent allocation
Rather than using the streaming API, use the coherent allocator to
provide this memory, thereby eliminating cache flushing of it each
time we map and unmap it. This results in a 7.5% increase in
transfer speed with a UHS-1 card operating in 3.3v mode at a clock
of 49.5MHz.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:58:29 +0000 (12:58 +0100)]
mmc: sdhci: avoid sync'ing the SG if there's no misalignment
On read, we don't need to sync the whole scatterlist and then check
whether any segments need copying - if we check first, we avoid
potentially expensive cache handling.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
The Freescale esdhc driver is the only driver which needs the interrupt
registers restored after a reset. Move this quirk to be part of the
ESDHC driver implementation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:57:12 +0000 (12:57 +0100)]
mmc: sdhci: convert reset into a library function
Rather than having platform_reset_enter/platform_reset_exit methods,
turn the core of the reset handling into a library function which
platforms can call at the appropriate moment in their (new) reset
method.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:57:07 +0000 (12:57 +0100)]
mmc: sdhci: convert generic bus width setup to library function
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:57:02 +0000 (12:57 +0100)]
mmc: sdhci: plug hole in disabling card detection interrupts
When we disable card detection interrupts, we should disable both the
insert and remove interrupts irrespective of the current state - this
avoids races between the hardware card detect changing state before
we've read that updated state and altered the interrupt mask.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:56:01 +0000 (12:56 +0100)]
mmc: sdhci: more efficient interrupt enable register handling
Rather than wasting cycles read-modify-writing the interrupt enable
registers, cache the value locally instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:55:56 +0000 (12:55 +0100)]
mmc: sdhci: allow sdio interrupts while sdhci runtime suspended
Allow SDIO interrupts to be received while the SDHCI host is runtime
suspended. We do this by leaving the AHB clock enabled while the
host is runtime suspended so we can access the SDHCI registers, and
so read and raise the SDIO card interrupt.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:55:51 +0000 (12:55 +0100)]
mmc: sdhci: push card_tasklet into threaded irq handler
There's no requirement to have the card tasklet separate now that we
have a threaded interrupt handler, so kill this and move the called
code into the threaded part of the handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:55:46 +0000 (12:55 +0100)]
mmc: sdhci: convert to new SDIO IRQ handling
Use a generic threaded interrupt handler for SDIO interrupt handling,
rather than allowing the SDIO core code to buggily spawn its own
thread. This results in host drivers to be more in control of how
SDIO interrupts are acknowledged in the hardware, rather than having
the internals of the SDIO core placed upon them, possibly resulting
in sub-standard handling.
At least one SDHCI implementation specifies a very specific sequence
to deal with a card interrupt.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:55:41 +0000 (12:55 +0100)]
mmc: sdhci: clean up sdio interrupt enable handling
We don't need to change the SDHCI_SDIO_IRQ_ENABLED flag when we're
merely receiving an interrupt - IRQ handling thread in the MMC core
will either re-enable or disable the interrupt via the enable_sdio_irq
callback, which will update this status appropriately.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:55:36 +0000 (12:55 +0100)]
mmc: sdhci: clean up interrupt handling
sdhci interrupt handling is a mess; there is a lot of code doing very
similar things. Let's clean this up a bit:
1. set's clear down cmd, data and bus power interrupts in one go - we're
always going to handle these.
2. use a do { } while () loop for looping while there are pending
interrupts.
3. group clearing of bits in intmask into one place.
This results in the code becoming simpler and easier to read.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Russell King [Fri, 25 Apr 2014 11:55:30 +0000 (12:55 +0100)]
mmc: sdio_irq: rework sdio irq handling
Rather than the SDIO support spawning it's own thread for handling card
interrupts, use the generic IRQ infrastructure for this, triggering it
from the host interface's interrupt handling directly.
This avoids a race between the parent thread waiting to receive an
interrupt response from the card, and the slow startup from the sdio
irq thread, which can occur as a result of high system load (eg, while
udev is running.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com>
[Ulf Hansson] Resolved conflict Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Nick Sanders [Wed, 7 May 2014 01:52:38 +0000 (18:52 -0700)]
mmc: sdhci: remove mdelay in eMMC tuning
This patch removes an unneccesary 1ms mdelay in the HS200 tuning
loop, called 40 times per retuning. Currently this causes a latency
of >40ms on any emmc accesses triggering wake from runtime PM,
which can occur for a significant portion of reads on a mostly idle system.
The delay is left in place for SD Cards, which use
MMC_SEND_TUNING_BLOCK rather than MMC_SEND_TUNING_BLOCK_HS200.
I'm not able to find evidence that this is required for SD in the
specs I have access to, however this delay has been present from
initial checkin for SD so I have preserved the original behavior for
compatibility.
This has been verified to fix observed glitching on local audio
playback and recording on apps with inbuilt assumptions on storage
latency.
Signed-off-by: Nick Sanders <nsanders@chromium.org> Reviewed-by: Grant Grundler <grundler@chromium.org> Reviewed-by: Doug Anderson <dianders@chromium.org> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Tim Kryger [Tue, 6 May 2014 22:57:01 +0000 (15:57 -0700)]
mmc: core: Improve support for deferred regulators
Callers of mmc_regulator_get_supply could benefit from knowing if either
of the regulators are present but not yet available. Since callers do
not currently examine the return value, modify this function to return
zero or -EPROBE_DEFER if either regulator get returns the same.
Furthermore, since callers check vmmc/vqmmc using IS_ERR and can deal
with absent regulators, switch to devm_regulator_get_optional. This has
the added benefit of allowing this function to behave correctly even in
the !CONFIG_REGULATOR case such that the stub can be removed.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Arnd Bergmann [Thu, 8 May 2014 08:27:54 +0000 (10:27 +0200)]
mmc: rtsx: fix possible linking error if built-in
rtsx_usb_sdmmc module uses the LED classdev if available, but the code
failed to consider the situation that it is built-in and the LED classdev is a
module, leading to following linking error:
LD init/built-in.o
drivers/built-in.o: In function `rtsx_usb_sdmmc_drv_remove':
rtsx_usb_sdmmc.c:(.text+0x2a018e): undefined reference to
`led_classdev_unregister'
drivers/built-in.o: In function `rtsx_usb_sdmmc_drv_probe':
rtsx_usb_sdmmc.c:(.text+0x2a197e): undefined reference to
`led_classdev_register'
Fix by excluding such condition when defining macro RTSX_USB_USE_LEDS_CLASS.
Signed-off-by: Roger Tseng <rogerable@realtek.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Daniel Willmann [Sat, 19 Apr 2014 21:59:18 +0000 (23:59 +0200)]
mmc: mxs: fix card detection function for broken card detect
Return -ENOSYS in get_cd if broken-cd is specified in the device tree.
Commit a91fe279ae75 (mmc: mxs: use standard flag for broken card
detection) sets MMC_CAP_NEEDS_POLL when broken-cd is specified. This
driver sets this flag unconditionally as it does not support a card
detect interrupt. Instead, broken-cd means that there is no card detect
signal connected.
The mmc core checks the get_cd function return value to determine if a
card is present. Only for a non-zero return value it will attempt to
initialize the card. So retuning -ENOSYS will allow the card to be
initialized.
For comparison, mmc_gpio_get_cd in slot-gpio.c also returns -ENOSYS if
the card detect GPIO is not valid.
Signed-off-by: Daniel Willmann <daniel@totalueberwachung.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Alex Smith [Tue, 29 Apr 2014 12:54:54 +0000 (13:54 +0100)]
mmc: jz4740: don't wait for PRG_DONE after stop command with R1 response
As of commit bcc3e1726d ("mmc: block: Use R1 responses for stop cmds for
read requests"), stop commands for reads do not have MMC_RSP_BUSY set.
In this case we should not wait for a PRG_DONE IRQ after sending the
stop command: it will not get raised when the busy flag is not set,
causing the request to fail with a timeout.
Signed-off-by: Alex Smith <alex.smith@imgtec.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Ulf Hansson <ulf.hansson@linaro.org> Cc: Chris Ball <chris@printf.net> Cc: James Hogan <james.hogan@imgtec.com> Acked-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
mmc: core: add DT bindings for eMMC HS400 1.8/1.2V
Provide the option to configure these speed modes per host,
for those host driver's that can't distinguish this in runtime.
Specially, if host can support HS400, it means that host can also
support HS200.
This patch adds HS400 mode support for eMMC5.0 device. HS400 mode is high
speed DDR interface timing from HS200. Clock frequency is up to 200MHz
and only 8-bit bus width is supported. In addition, tuning process of
HS200 is required to synchronize the command response on the CMD line
because CMD input timing for HS400 mode is the same as HS200 mode.
Current implementation for bus speed mode selection is too
complicated. This patch is to simplify the codes and remove
some duplicate parts.
The following changes are including:
* Adds functions for each mode selection(HS, HS-DDR, HS200 and etc)
* Rearranged the mode selection sequence with supported device type
* Adds maximum speed for HS200 mode(hs200_max_dtr)
* Adds field definition for HS_TIMING of EXT_CSD
SDIO controllers found on Marvell Kirkwood SoCs seem to cause a late,
spurious irq although all interrupts have been disabled. This irq
doesn't do any harm, neither to HW nor driver. To avoid some
"unexpected irq" warning later, we workaround above issue by bailing
out of irq handler early, if we didn't expect any.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
mvsdio reports method of card detection with dev_notice, while for
removable cards it may be sane, for non-removable cards it is not.
Also, as the user cannot do anything about it, silence the message
by reducing it from dev_notice to dev_dbg.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Tim Kryger [Thu, 24 Apr 2014 21:44:26 +0000 (14:44 -0700)]
mmc: core: Try other signal levels during power up
The eMMC signalling voltage is determined by VCCQ which is provided to
the card by the host. Signalling is not required to begin at 3.3v and,
if the host and card both support a particular VCC/VCCQ combination, it
can be used immediately.
In contrast, SD Cards must begin with 3.3v signalling and may switch to
a lower voltage signalling if instructed to do so in CMD11. A message
is required to coordinate this operation because the card only receives
a 3.3v VDD and must know when to use the 1.8v produced by its internal
regulator.
It makes sense for the core to begin with 3.3v signalling but when that
can't be set, 1.8v and 1.2v signalling also should be attempted. This
is especially important when an external regulator with a limited range
is used to supply VCCQ to an eMMC part.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Jaehoon Chung [Mon, 3 Mar 2014 02:36:43 +0000 (11:36 +0900)]
mmc: dw_mmc: remove unused member variable.
Since using the device-tree, didn't use the callback pointer.
So removed the unused callback pointer.
When the set_power callback is used, it should be added in future.
Micky Ching [Thu, 27 Mar 2014 05:35:04 +0000 (13:35 +0800)]
mmc: rtsx: add R1-no-CRC mmc command type handle
a27fbf2f067b0cd ("mmc: add ignorance case for CMD13 CRC error") produced
a cmd.flags unhandled in realtek pci host driver. This will make MMC
card fail to initialize, this patch is used to handle the new cmd.flags
condition and MMC card can be used.
Ulf Hansson [Fri, 28 Feb 2014 11:49:00 +0000 (12:49 +0100)]
mmc: core: Invoke sdio func driver's PM callbacks from the sdio bus
The sdio func device is added to the driver model after the card
device.
This means the sdio func device will be suspend before the card device
and thus resumed after. The consequence are the mmc core don't
explicity need to protect itself from receiving sdio requests in
suspended state. Instead that can be handled from the sdio bus, which
is thus invokes the PM callbacks instead of old dummy function.
In the case were the sdio func driver don't implement the PM callbacks
the mmc core will in the early phase of system suspend, remove the
card from the driver model and thus power off it.
Cc: Aaron Lu <aaron.lu@intel.com> Cc: NeilBrown <neilb@suse.de> Cc: Rafael J. Wysocki <rjw@rjwysocki.net> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Aaron Lu <aaron.lu@intel.com> Tested-by: xiaoming wang <xiaoming.wang@intel.com> Tested-by: Chuanxiao Dong <chuanxiao.dong@intel.com> Signed-off-by: Chris Ball <chris@printf.net>
Stefan Wahren [Thu, 3 Apr 2014 15:32:05 +0000 (17:32 +0200)]
mmc: core: Use maximum timeout values in case TACC field is zero
When plugging a specific micro SD card at MMC socket of a custom i.MX28 board,
we get the following kernel warning:
WARNING: CPU: 0 PID: 30 at drivers/mmc/host/mxs-mmc.c:342 mxs_mmc_start_cmd+0x34c/0x378()
Modules linked in:
CPU: 0 PID: 30 Comm: kworker/u2:1 Not tainted 3.14.0-rc5 #8
Workqueue: kmmcd mmc_rescan
[<c0015420>] (unwind_backtrace) from [<c0012cb0>] (show_stack+0x10/0x14)
[<c0012cb0>] (show_stack) from [<c001daf8>] (warn_slowpath_common+0x6c/0x8c)
[<c001daf8>] (warn_slowpath_common) from [<c001db34>] (warn_slowpath_null+0x1c/0x24)
[<c001db34>] (warn_slowpath_null) from [<c0349478>] (mxs_mmc_start_cmd+0x34c/0x378)
[<c0349478>] (mxs_mmc_start_cmd) from [<c0338fa0>] (mmc_start_request+0xc4/0xf4)
[<c0338fa0>] (mmc_start_request) from [<c03390b4>] (mmc_wait_for_req+0x50/0x164)
[<c03390b4>] (mmc_wait_for_req) from [<c03405b8>] (mmc_app_send_scr+0x158/0x1c8)
[<c03405b8>] (mmc_app_send_scr) from [<c033ee1c>] (mmc_sd_setup_card+0x80/0x3c8)
[<c033ee1c>] (mmc_sd_setup_card) from [<c033f788>] (mmc_sd_init_card+0x124/0x66c)
[<c033f788>] (mmc_sd_init_card) from [<c033fd7c>] (mmc_attach_sd+0xac/0x174)
[<c033fd7c>] (mmc_attach_sd) from [<c033a658>] (mmc_rescan+0x25c/0x2d8)
[<c033a658>] (mmc_rescan) from [<c003597c>] (process_one_work+0x1b4/0x4ec)
[<c003597c>] (process_one_work) from [<c0035de4>] (worker_thread+0x130/0x464)
[<c0035de4>] (worker_thread) from [<c003c824>] (kthread+0xb4/0xd0)
[<c003c824>] (kthread) from [<c000f420>] (ret_from_fork+0x14/0x34)
The error is due to an invalid value in CSD register of a specific 2GB
micro SD card. The CSD version of this card is 1.0 but the TACC field
has the invalid value 0.
Since the kernel is making use of this TACC field to calculate the SD
card timeout, an invalid value 0 leads to a warning at
mxs_ns_to_ssp_ticks() and later the following misleading error message
appears in a loop:
mxs-mmc 80010000.ssp: card claims to support voltages below defined range
mxs-mmc 80010000.ssp: no support for card's volts
mmc0: error -22 whilst initialising MMC card
This error is only found on this 2GB SD card on mxs platform.
On x86 this card works without any problems.
The following patch based on the work of Peter Chan and Otavio Salvador.
It catches the case that the determined timeout is still 0 and sets it
to a valid value.
Successful tested on a i.MX28 board.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine fixes from Vinod Koul:
"Back from long weekend here in India and now the time to send fixes
for slave dmaengine.
- Dan's fix of sirf xlate code
- Jean's fix for timberland
- edma fixes by Sekhar for SG handling and Yuan for changing init
call"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: fix eDMA driver as a subsys_initcall
dmaengine: sirf: off by one in of_dma_sirfsoc_xlate()
platform: Fix timberdale dependencies
dma: edma: fix incorrect SG list handling
Merge tag 'iommu-fixes-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"Fixes for regressions:
- fix wrong IOMMU enumeration causing some SCSI device drivers
initialization failures
- ARM-SMMU fixes for a panic condition and a wrong return value"
* tag 'iommu-fixes-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/arm-smmu: fix panic in arm_smmu_alloc_init_pte
iommu/arm-smmu: Return 0 on unmap failure
iommu/vt-d: fix bug in matching PCI devices with DRHD/RMRR descriptors
iommu/vt-d: Fix get_domain_for_dev() handling of upstream PCIe bridges
iommu/vt-d: fix memory leakage caused by commit ea8ea46
Adrien BAK [Fri, 18 Apr 2014 02:00:43 +0000 (11:00 +0900)]
perf tools: Improve error reporting
In the current version, when using perf record, if something goes
wrong in tools/perf/builtin-record.c:375
session = perf_session__new(file, false, NULL);
The error message:
"Not enough memory for reading per file header"
is issued. This error message seems to be outdated and is not very
helpful. This patch proposes to replace this error message by
"Perf session creation failed"
I believe this issue has been brought to lkml:
https://lkml.org/lkml/2014/2/24/458
although this patch only tackles a (small) part of the issue.
Additionnaly, this patch improves error reporting in
tools/perf/util/data.c open_file_write.
Currently, if the call to open fails, the user is unaware of it.
This patch logs the error, before returning the error code to
the caller.
Reported-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Adrien BAK <adrien.bak@metascale.org> Link: http://lkml.kernel.org/r/1397786443.3093.4.camel@beast
[ Reorganize the changelog into paragraphs ]
[ Added empty line after fd declaration in open_file_write ] Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Vladimir Nikulichev <nvs@tbricks.com> Tested-by: Namhyung Kim <namhyung@kernel.org> Reviewed-by: Adrian Hunter <adrian.hunter@intel.com> Link: http://lkml.kernel.org/r/969812.163009436-sendEmail@nvs Signed-off-by: Jiri Olsa <jolsa@redhat.com>
perf kvm: Fix 'Min time' counting in report command
Every event in the perf-kvm has a 'stats' structure, which contains
max/min/average/etc times of handling this event.
The problem is that the 'perf-kvm stat report' command always shows
that 'min time' is 0us for every event. Example:
This happens because the 'stats' structure is not initialized and
stats->min equals to 0. Lets initialize the structure for every
event after its allocation using init_stats() function. This initializes
stats->min to -1 and makes 'Min time' statistics counting work:
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Unfortunately this contains no easter eggs, its a bit larger than I'd
like, but I included a patch that just moves code from one file to
another and I'd like to avoid merge conflicts with that later, so it
makes it seem worse than it is,
Otherwise:
- radeon: fixes to use new microcode to stabilise some cards, use
some common displayport code, some runtime pm fixes, pll regression
fixes
- i915: fix for some context oopses, a warn in a used path, backlight
fixes
- nouveau: regression fix
- omap: a bunch of fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (51 commits)
drm: bochs: drop unused struct fields
drm: bochs: add power management support
drm: cirrus: add power management support
drm: Split out drm_probe_helper.c from drm_crtc_helper.c
drm/plane-helper: Don't fake-implement primary plane disabling
drm/ast: fix value check in cbr_scan2
drm/nouveau/bios: fix a bit shift error introduced by 457e77b
drm/radeon/ci: make sure mc ucode is loaded before checking the size
drm/radeon/si: make sure mc ucode is loaded before checking the size
drm/radeon: improve PLL params if we don't match exactly v2
drm/radeon: memory leak on bo reservation failure. v2
drm/radeon: fix VCE fence command
drm/radeon: re-enable mclk dpm on R7 260X asics
drm/radeon: add support for newer mc ucode on CI (v2)
drm/radeon: add support for newer mc ucode on SI (v2)
drm/radeon: apply more strict limits for PLL params v2
drm/radeon: update CI DPM powertune settings
drm/radeon: fix runpm handling on APUs (v4)
drm/radeon: disable mclk dpm on R7 260X
drm/tegra: Remove gratuitous pad field
...
Dave Airlie [Sat, 19 Apr 2014 01:16:02 +0000 (11:16 +1000)]
Merge branch 'drm-next-3.15-wip' of git://people.freedesktop.org/~deathsimple/linux into drm-next
Some i2c fixes over DisplayPort.
* 'drm-next-3.15-wip' of git://people.freedesktop.org/~deathsimple/linux:
drm/radeon: Improve vramlimit module param documentation
drm/radeon: fix audio pin counts for DCE6+ (v2)
drm/radeon/dp: switch to the common i2c over aux code
drm/dp/i2c: Update comments about common i2c over dp assumptions (v3)
drm/dp/i2c: send bare addresses to properly reset i2c connections (v4)
drm/radeon/dp: handle zero sized i2c over aux transactions (v2)
drm/i915: support address only i2c-over-aux transactions
drm/tegra: dp: Support address-only I2C-over-AUX transactions
1) Fix mlx4_en_netpoll implementation, it needs to schedule a NAPI
context, not synchronize it. From Chris Mason.
2) Ipv4 flow input interface should never be zero, it should be
LOOPBACK_IFINDEX instead. From Cong Wang and Julian Anastasov.
3) Properly configure MAC to PHY connection in mvneta devices, from
Thomas Petazzoni.
4) sys_recv should use SYSCALL_DEFINE. From Jan Glauber.
5) Tunnel driver ioctls do not use the correct namespace, fix from
Nicolas Dichtel.
6) Fix memory leak on seccomp filter attach, from Kees Cook.
7) Fix lockdep warning for nested vlans, from Ding Tianhong.
8) Crashes can happen in SCTP due to how the auth_enable value is
managed, fix from Vlad Yasevich.
9) Wireless fixes from John W Linville and co.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
net: sctp: cache auth_enable per endpoint
tg3: update rx_jumbo_pending ring param only when jumbo frames are enabled
vlan: Fix lockdep warning when vlan dev handle notification
seccomp: fix memory leak on filter attach
isdn: icn: buffer overflow in icn_command()
ip6_tunnel: use the right netns in ioctl handler
sit: use the right netns in ioctl handler
ip_tunnel: use the right netns in ioctl handler
net: use SYSCALL_DEFINEx for sys_recv
net: mdio-gpio: Add support for separate MDI and MDO gpio pins
net: mdio-gpio: Add support for active low gpio pins
net: mdio-gpio: Use devm_ functions where possible
ipv4, route: pass 0 instead of LOOPBACK_IFINDEX to fib_validate_source()
ipv4, fib: pass LOOPBACK_IFINDEX instead of 0 to flowi4_iif
mlx4_en: don't use napi_synchronize inside mlx4_en_netpoll
net: mvneta: properly configure the MAC <-> PHY connection in all situations
net: phy: add minimal support for QSGMII PHY
sfc:On MCDI timeout, issue an FLR (and mark MCDI to fail-fast)
mwifiex: fix hung task on command timeout
mwifiex: process event before command response
...
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"A set of 5 small cifs fixes"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cif: fix dead code
cifs: fix error handling cifs_user_readv
fs: cifs: remove unused variable.
Return correct error on query of xattr on file with empty xattrs
cifs: Wait for writebacks to complete before attempting write.
Merge tag 'char-misc-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a few driver fixes for char/misc drivers that resolve
reported issues.
All have been in linux-next successfully for a few days"
* tag 'char-misc-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Drivers: hv: vmbus: Negotiate version 3.0 when running on ws2012r2 hosts
Tools: hv: Handle the case when the target file exists correctly
vme_tsi148: Utilize to_pci_dev() macro
vme_tsi148: Fix PCI address mapping assumption
vme_tsi148: Fix typo in tsi148_slave_get()
w1: avoid recursive device_add
w1: fix netlink refcnt leak on error path
misc: Grammar s/addition/additional/
drivers: mcb: fix memory leak in chameleon_parse_cells() error path
mei: ignore client writing state during cb completion
mei: me: do not load the driver if the FW doesn't support MEI interface
GenWQE: Increase driver version number
GenWQE: Fix multithreading problems
GenWQE: Ensure rc is not returning an uninitialized value
GenWQE: Add wmb before DDCB is started
GenWQE: Enable access to VPD flash area
Merge tag 'driver-core-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some driver core fixes for 3.15-rc2. Also in here are some
documentation updates, as well as an API removal that had to wait for
after -rc1 due to the cleanups coming into you from multiple developer
trees (this one and the PPC tree.)
All have been in linux next successfully"
* tag 'driver-core-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers/base/dd.c incorrect pr_debug() parameters
Documentation: Update stable address in Chinese and Japanese translations
topology: Fix compilation warning when not in SMP
Chinese: add translation of io_ordering.txt
stable_kernel_rules: spelling/word usage
sysfs, driver-core: remove unused {sysfs|device}_schedule_callback_owner()
kernfs: protect lazy kernfs_iattrs allocation with mutex
fs: Don't return 0 from get_anon_bdev
Merge tag 'staging-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are a few staging driver fixes for issues that have been reported
for 3.15-rc2.
Also dominating the diffstat for the pull request is the removal of
the rtl8187se driver. It's no longer needed in staging as a "real"
driver for this hardware is now merged in the tree in the "correct"
location in drivers/net/
All of these patches have been tested in linux-next"
* tag 'staging-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: Fix case where ethtype was never obtained and always be checked against 0
staging: r8712u: Fix case where ethtype was never obtained and always be checked against 0
staging: r8188eu: Calling rtw_get_stainfo() with a NULL sta_addr will return NULL
staging: comedi: fix circular locking dependency in comedi_mmap()
staging: r8723au: Add missing initialization of change_inx in sort algorithm
Staging: unisys: use after free in list_for_each()
staging: unisys: use after free in error messages
staging: speakup: fix misuse of kstrtol() in handle_goto()
staging: goldfish: Call free_irq in error path
staging: delete rtl8187se wireless driver
staging: rtl8723au: Fix buffer overflow in rtw_get_wfd_ie()
staging: gs_fpgaboot: remove __TIMESTAMP__ macro
staging: vme: fix memory leak in vme_user_probe()
staging: fpgaboot: clean up Makefile
staging/usbip: fix store_attach() sscanf return value check
staging/usbip: userspace - fix usbipd SIGSEGV from refresh_exported_devices()
staging: rtl8188eu: remove spaces, correct counts to unbreak P2P ioctls
staging/rtl8821ae: Fix OOM handling in _rtl_init_deferred_work()
Merge tag 'tty-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small tty/serial driver fixes for 3.15-rc2. Also
in here are some Documentation file removals for drivers that we
removed a long time ago, no need to keep it around any longer.
All of these have been in linux-next for a bit"
* tag 'tty-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: 8250, disable "too much work" messages"
serial: amba-pl011: fix regression, causing an Oops on rmmod
tty: Fix help text of SYNCLINK_CS
tty: fix memleak in alloc_pid
ttyprintk: Allow built as a module
ttyprintk: Fix wrong tty_unregister_driver() call in the error path
serial: 8250, disable "too much work" messages
Documentation/serial: Delete obsolete driver documentation
serial: omap: Fix missing pm_runtime_resume handling by simplifying code
serial_core: Fix pm imbalance on unbind
serial: pl011: change Rx burst size to half of trigger level
serial: timberdale: Depend on X86_32
serial: st-asc: Fix SysRq char handling
Revert "serial: clps711x: Give a chance to perform useful tasks during wait loop"
serial_core: Fix conditional start_tx on ring buffer not empty
serial: efm32: use $vendor,$device scheme for compatible string
serial: omap: free the wakeup settings in remove
Merge tag 'usb-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of tiny USB fixes and new device ids for 3.15-rc2.
Nothing major, just issues some people have reported.
All of these have been in linux-next"
* tag 'usb-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
uas: fix deadlocky memory allocations
uas: fix error handling during scsi_scan()
uas: fix GFP_NOIO under spinlock
uwb: adds missing error handling
USB: cdc-acm: Remove Motorola/Telit H24 serial interfaces from ACM driver
USB: ohci-jz4740: FEAT_POWER is a port feature, not a hub feature
USB: ohci-jz4740: Fix uninitialized variable warning
USB: EHCI: tegra: set txfill_tuning
usb: ehci-platform: Return immediately from suspend if ehci_suspend fails
usb: ehci-exynos: Return immediately from suspend if ehci_suspend fails
USB: fix crash during hotplug of PCI USB controller card
USB: cdc-acm: fix double usb_autopm_put_interface() in acm_port_activate()
usb: usb-common: fix typo for usb_state_string
USB: usb_wwan: fix handling of missing bulk endpoints
USB: pl2303: add ids for Hewlett-Packard HP POS pole displays
USB: cp210x: Add 8281 (Nanotec Plug & Drive)
usb: option driver, add support for Telit UE910v2
Revert "USB: serial: add usbid for dell wwan card to sierra.c"
USB: serial: ftdi_sio: add id for Brainboxes serial cards
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
thp: close race between split and zap huge pages
mm: fix new kernel-doc warning in filemap.c
mm: fix CONFIG_DEBUG_VM_RB description
mm: use paravirt friendly ops for NUMA hinting ptes
mips: export flush_icache_range
mm/hugetlb.c: add cond_resched_lock() in return_unused_surplus_pages()
wait: explain the shadowing and type inconsistencies
Shiraz has moved
Documentation/vm/numa_memory_policy.txt: fix wrong document in numa_memory_policy.txt
powerpc/mm: fix ".__node_distance" undefined
kernel/watchdog.c:touch_softlockup_watchdog(): use raw_cpu_write()
init/Kconfig: move the trusted keyring config option to general setup
vmscan: reclaim_clean_pages_from_list() must use mod_zone_page_state()
projects / linux-beck.git / log