Alexander Duyck [Tue, 26 Aug 2008 11:25:11 +0000 (04:25 -0700)]
igb: clean up a stray fake netdev code left in rx path
Remove code that was in place to support fake netdev
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alexander Duyck [Tue, 26 Aug 2008 11:25:08 +0000 (04:25 -0700)]
igb: remove unneeded cleaned variable in clean_tx_irq path
The cleaned variable can be replaced by the count of packets cleaned during
the tx interrupt routine so it can be removed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bruce Allan [Wed, 27 Aug 2008 01:37:06 +0000 (18:37 -0700)]
e1000e: add support for new 82574L part
This new part has the same feature set as previous parts with the addition
of MSI-X support.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bruce Allan [Wed, 27 Aug 2008 01:36:50 +0000 (18:36 -0700)]
e1000e: add support for 82567LM-3 and 82567LF-3 (ICH10D) parts
Add support for new LOM devices on the latest generation ICHx platforms.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bruce Allan [Wed, 27 Aug 2008 01:36:36 +0000 (18:36 -0700)]
e1000e: add support for the 82567LM-4 device
Enable PCI device ID for a new combination of MAC and PHY already supported
in the driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PJ Waskiewicz [Tue, 26 Aug 2008 11:27:30 +0000 (04:27 -0700)]
ixgbe: use different context for tso and offload
Change TSO offloads to use a different context than VLAN insertion
and Tx checksumming. Hardware has separate registers internally for
storing these so use them.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Jesse Brandeburg [Tue, 26 Aug 2008 11:27:21 +0000 (04:27 -0700)]
ixgbe: update dca to new interface, fix CONFIG_DCA_MODULE
DCA related fixes
=================
- ixgbe was not compiling and using DCA correctly if dca was a module
- DCA interface changed with new kernel
- ixgbe was not correctly configured to indicate DCA hints to the
correct CPU.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Jesse Brandeburg [Tue, 26 Aug 2008 11:27:18 +0000 (04:27 -0700)]
ixgbe: should not use HW_CSUM, should use IP* flags
as mentioned by Herbert, our hardware supports IP offloads, not full
checksum offloads for any protocol in existence (even though the
hardware just provides generic csum support over any range of bytes)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Jesse Brandeburg [Tue, 26 Aug 2008 11:27:16 +0000 (04:27 -0700)]
ixgbe: Lock RSS seed, move rx_buf_len to the rx_ring
This locks the seed down so loading/unloading the driver will present
predictable hashing from RSS. Also move the rx_buf_len out of the adapter
struct, and into the Rx ring struct.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Jesse Brandeburg [Tue, 26 Aug 2008 11:27:13 +0000 (04:27 -0700)]
ixgbe: Implement Tx Head Writeback
Enable Tx Head Writeback in the hardware. This helps performance by
removing adapter writebacks to descriptors on transmit completion.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Jesse Brandeburg [Tue, 26 Aug 2008 11:27:08 +0000 (04:27 -0700)]
ixgbe: Cleanup references to Tx and Rx rings to becommon across the driver
Cleanup all the different references to the Tx ring and Rx ring structures
and make them common across the driver.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement HAVE_SET_RX_MODE in the driver for MC and UC lists.
Signed-off-by: Christopher Leech <christopher.leech@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Jesse Brandeburg [Tue, 26 Aug 2008 11:26:56 +0000 (04:26 -0700)]
ixgbe: fix rx csum return status misinterpretation
the driver was misinterpreting rx_csum return value in the descriptor
so occassionally we would indicate an rx_csum error in our stats
when there was none. This would have no effect on traffic because
we would just hand the packet to the stack anyway without the offload
flag set, but would increase CPU for those packets that needed a recompute.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Randy Dunlap [Tue, 2 Sep 2008 20:03:44 +0000 (13:03 -0700)]
hp-plus: fix link objects
Fix hp-plus Makefile object file:
drivers/built-in.o: In function `hpp_open':
hp-plus.c:(.text+0xaf445): undefined reference to `ei_interrupt'
hp-plus.c:(.text+0xaf4ac): undefined reference to `ei_open'
drivers/built-in.o: In function `hpp_close':
hp-plus.c:(.text+0xaf59d): undefined reference to `ei_close'
drivers/built-in.o: In function `hpp_probe1':
hp-plus.c:(.init.text+0x7314): undefined reference to `ei_poll'
drivers/built-in.o: In function `hp_plus_probe':
(.init.text+0x7407): undefined reference to `__alloc_ei_netdev'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ben Hutchings [Mon, 1 Sep 2008 11:48:08 +0000 (12:48 +0100)]
sfc: Cleanup RX event processing
Make efx_process_channel() and falcon_process_eventq() return the
number of packets received rather than updating the quota, consistent
with new NAPI.
Since channels and RX queues are mapped one-to-one, remove return
value from falcon_handle_rx_event() and add a warning for events
with the wrong RX queue number.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ben Hutchings [Mon, 1 Sep 2008 11:47:12 +0000 (12:47 +0100)]
sfc: Removed forced inlining of long functions
gcc will automatically inline static functions with only one caller, and
may inline other functions depending on the kernel configuration and size
of the intermediate code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ben Hutchings [Mon, 1 Sep 2008 11:46:33 +0000 (12:46 +0100)]
sfc: Speed up loopback self-test
Add efx_poll_loopback() function to test for successful completion of test.
Change efx_test_loopback() to end the test after 1 ms if
efx_poll_loopback() indicates success, and otherwise to wait for 100 ms
as before.
While we're here, rename efx_{rx,tx}_loopback() to
efx_{begin,end}_loopback() which more accurately reflect their
purpose.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ben Hutchings [Mon, 1 Sep 2008 11:45:08 +0000 (12:45 +0100)]
sfc: Avoid mangling error codes in efx_test_loopback()
efx_test_loopback() used "|" to combine the results of the RX and TX
phases. If both phases fail with different error codes, this results
in a bogus error code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ben Hutchings [Mon, 1 Sep 2008 11:44:59 +0000 (12:44 +0100)]
sfc: Use separate hardware TX queues to select checksum generation
Checksum generation is an attribute of our hardware TX queues, not TX
descriptors. We previously used a single queue and turned checksum
generation on or off as requested through ethtool. However, this can
result in regenerating checksums in raw packets that should not be
modified. We now create 2 hardware TX queues with checksum generation
on or off. They are presented to the net core as one queue since it
does not know how to select between them.
The self-test verifies that a bad checksum is unaltered on the queue
with checksum generation off.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Thomas Graf [Wed, 3 Sep 2008 00:30:27 +0000 (17:30 -0700)]
netlink: Remove compat API for nested attributes
Removes all _nested_compat() functions from the API. The prio qdisc
no longer requires them and netem has its own format anyway. Their
existance is only confusing.
Resend: Also remove the wrapper macro.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 29 Aug 2008 21:37:23 +0000 (14:37 -0700)]
net: Unbreak userspace usage of linux/mroute.h
Nothing in linux/pim.h should be exported to userspace.
This should fix the XORP build failure reported by
Jose Calhariz, the debain package maintainer.
Nothing originally in linux/mroute.h was exported to userspace
ever, but some of this stuff started to be when it was moved into
this new linux/pim.h, and that was wrong. If we didn't provide these
definitions for 10 years we can reasonably expect that applications
defined this stuff locally or used GLIBC headers providing the
protocol definitions. And as such the only result of this can
be conflict and userland build breakage.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Fri, 29 Aug 2008 21:21:52 +0000 (14:21 -0700)]
pkt_sched: Fix locking of qdisc_root with qdisc_root_sleeping_lock()
Use qdisc_root_sleeping_lock() instead of qdisc_root_lock() where
appropriate. The only difference is while dev is deactivated, when
currently we can use a sleeping qdisc with the lock of noop_qdisc.
This shouldn't be dangerous since after deactivation root lock could
be used only by gen_estimator code, but looks wrong anyway.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Buesch [Thu, 28 Aug 2008 17:33:40 +0000 (19:33 +0200)]
b43: Rewrite TX power adjustment
This patch rewrites the TX power recalculation algorithms to scale better
with changed enviromnent. If there's low
TX traffic, the power will be checked against the desired values
every 60 seconds.
If there is high TX traffic, the check is redone every 2 seconds. This improves
the reaction times a lot and confuses the rate control less.
It will also reduce the time it initially takes to tune to a new TX power
value. With the old algorithm it could take about 30 to 45 seconds to settle to
a new power value. This will happen in about two to four seconds now.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mattias Nissler [Fri, 29 Aug 2008 19:07:20 +0000 (21:07 +0200)]
rt2x00: skb->data pointer should not include TX descriptor
Make sure the skb->data pointer points to the frame data, not the TX
descriptor. The frame dumping code relies on that.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Fri, 29 Aug 2008 19:07:16 +0000 (21:07 +0200)]
rt2x00: Add Signal type flag
Instead of using the PLCP flag to indicate if the
signal value is plcp or the bitrate we should add
a new flag to mark the bitrate type explicitely.
This is usefull when new types are added later for
rt2800.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Fri, 29 Aug 2008 19:05:45 +0000 (21:05 +0200)]
rt2x00: Initialize txop during conf_tx() callback
The txop parameter is supported by rt61pci and rt73usb,
and thus should be written to the register instead
of using the fixed value set during initialization.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mattias Nissler [Fri, 29 Aug 2008 19:05:21 +0000 (21:05 +0200)]
rt2x00: Only configure hardware when radio is enabled
Some hardware configuration registers such as antenna and channel configuration
can only be written when the radio is enabled. Previously, we didn't consider
this, so some configuration items could be set inconsistently after reenabling
the radio. This patch changes the config() handler to only reprogram the
hardware when the radio is enabled. Configuration changes that are made while
the radio is off are postponed until the radio is switched back on. We also
leave the radio turned off during initialization and only enable it when
requested by mac80211. This allows us to get rid of the DIRTY_CONFIG flag,
because the device is now guaranteed to be completely initialized when brought
up by mac80211.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Fri, 29 Aug 2008 19:04:50 +0000 (21:04 +0200)]
rt2x00: Map extra_tx_headroom to DMA
If a driver requests additional headroom it should
be mapped to DMA as well because it will be send to
the hardware as well (as form of extra descriptor).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Fri, 29 Aug 2008 19:04:26 +0000 (21:04 +0200)]
rt2x00: Fix race conditions in flag handling
Some of the flags should be accessed atomically to
prevent race conditions. The flags that are most important
are those that can change often and indicate the actual
state of the device, queue or queue entry.
The big flag rename was done to move all state flags to
the same naming type as the other rt2x00dev flags and
made sure all places where the flags were used were changed. ;)
Thanks to Stephen for most of the queue flags updates,
which fixes some of the most obvious consequences of the
race conditions. Among those the notorious:
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rfkill: rename rfkill_mutex to rfkill_global_mutex
rfkill_mutex and rfkill->mutex are too easy to confuse with each other.
Rename rfkill_mutex to rfkill_global_mutex, so that they are easier to tell
apart with just one glance.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Cc: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
BUG_ON() and WARN() the heck out of buggy drivers calling into the rfkill
subsystem.
Also switch from WARN_ON(1) to the new descriptive WARN().
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felipe Balbi [Tue, 26 Aug 2008 14:57:58 +0000 (11:57 -0300)]
rfkill: add missing line break
Trivial patch adding a missing line break on
rfkill_claim_show().
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Acked-by: Ivo van Doorn <IvDoorn@gmail.co> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Switch sysfs parsing to something that actually works properly.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Mon, 25 Aug 2008 08:58:58 +0000 (11:58 +0300)]
mac80211/cfg80211: HT capabilities for NEW_STA
Allow userspace (e.g., hostapd) to set HT capabilities for associated
STAs. This is based on a patch from Zhu Yi <yi.zhu@intel.com> (only
the NL80211_ATTR_HT_CAPABILITY for NEW_STA part is included here).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever wondered why the signal was so bad with p54 compared to madwifi, or intel?
Well, if you have revision 1 rssi calibration curve points in your EEPROM, then wonder no more.
The firmware wants a extra 1 byte padding for every curve point. But someone forgot to put
them into the EEPROM's data structure...
So now, big question: what happens when we blindly "memcpy" these data points?
Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Huang Weiyi [Sat, 23 Aug 2008 05:56:25 +0000 (13:56 +0800)]
wireless: remove unused #include <version.h>
The driver(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/net/wireless/b43legacy/main.c
drivers/net/wireless/iwlwifi/iwl-3945-led.c
drivers/net/wireless/iwlwifi/iwl-led.c
drivers/net/wireless/iwlwifi/iwl-rfkill.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Fri, 22 Aug 2008 14:31:33 +0000 (17:31 +0300)]
ath9k: Use mac80211 for multicast power save buffering
Replace the internal ath9k implementation of multicast/broadcast frame
power save buffering (AP mode) in ath9k with use of mac80211
ieee80211_get_buffered_bc() mechanism. This removes quite a bit of
duplicated functionality and simplifies the driver part.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Thu, 21 Aug 2008 18:45:56 +0000 (21:45 +0300)]
mac80211_hwsim: Add minimal IEEE 802.11n support
Set some semi-random values for HT and add more queues to allow IEEE
802.11n association to be tested with mac80211_hwsim. This with the
latest hostapd git tree version can complete a simulated 802.11n
association successfully (with mac80211 client MLME).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Wed, 20 Aug 2008 22:45:06 +0000 (17:45 -0500)]
ssb: Clean up extraction of MAC addresses from SPROM
Only rev 1 and 2 ssb SPROMs have fields named et0mac and et1mac;
however, all of the extraction routines extract pseudo data for these
fields from regions that are all 1's resulting in a hardware address
of FF:FF:FF:FF:FF:FF. This patch forces such a fill at the beginning of
the data extraction process, and only does the formal extraction if the
SPROM rev is 1 or 2.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Tue, 19 Aug 2008 17:50:31 +0000 (12:50 -0500)]
ssb: Update for Rev. 5 SPROM
Although a revision 5 SPROM has not been seen in the wild, the
open-source portion of the MIPS driver 4.150.10.5 describes its
layout, which is mostly inherited from revision 4. This patch
implements the differences.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Acked-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-beck.git / log