Michel Dänzer [Tue, 20 Mar 2012 21:18:26 +0000 (17:18 -0400)]
drm/radeon: Update radeon_info_ioctl for SI. (v2)
v2: agd5f: add new MAX_PIPES param
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Tue, 20 Mar 2012 21:18:17 +0000 (17:18 -0400)]
drm/radeon/kms: add ucode loading for SI
Currently the driver required 5 sets of ucode:
1. pfp - pre-fetch parser, part of the CP
2. me - micro engine, part of the CP
3. ce - constant engine, part of the CP
4. rlc - interrupt controller
5. mc - memory controller
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Tue, 20 Mar 2012 21:18:14 +0000 (17:18 -0400)]
drm/radeon/kms: add support for the CONST IB to the CS ioctl
This adds a new chunk id to the CS ioctl to support the
INDIRECT_BUFFER_CONST packet.
On SI, the CP adds a new engine called the CE (Constant Engine)
which runs simulatenously with the DE (Drawing Engine, formerly
called the ME). This allows the CP to process two related IBs
simultaneously. The CE is tasked with loading the constant data
(constant buffers, resource descriptors, samplers, etc.) while
the DE loads context register state and issues drawing commands.
It's up to the userspace application to sychronize the CE and the
DE using special synchronization packets.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Tue, 20 Mar 2012 21:18:06 +0000 (17:18 -0400)]
drm/radeon/kms: DP aux updates for DCE6
DCE6 requires a non-0 value for lpAuxRequest for the
ProcessAuxChannelTransaction command table. Setting
lpAuxRequest to 0 is a special case used by AsicInit
for setting up the aux pads.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Tue, 20 Mar 2012 21:18:03 +0000 (17:18 -0400)]
drm/radeon/kms/atom: add support for crtc power gating
Each pair of crtcs (0/1, 2/3, 4/5) can be power gated.
Make sure the power is applied when the crtc is in use and
only power down the pair when both are off.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Carsten Emde [Sun, 18 Mar 2012 21:37:33 +0000 (22:37 +0100)]
drm: allow loading an EDID as firmware to override broken monitor
Broken monitors and/or broken graphic boards may send erroneous or no
EDID data. This also applies to broken KVM devices that are unable to
correctly forward the EDID data of the connected monitor but invent
their own fantasy data.
This patch allows to specify an EDID data set to be used instead of
probing the monitor for it. It contains built-in data sets of frequently
used screen resolutions. In addition, a particular EDID data set may be
provided in the /lib/firmware directory and loaded via the firmware
interface. The name is passed to the kernel as module parameter of the
drm_kms_helper module either when loaded
options drm_kms_helper edid_firmware=edid/1280x1024.bin
or as kernel commandline parameter
drm_kms_helper.edid_firmware=edid/1280x1024.bin
It is also possible to restrict the usage of a specified EDID data set
to a particular connector. This is done by prepending the name of the
connector to the name of the EDID data set using the syntax
edid_firmware=[<connector>:]<edid>
such as, for example,
edid_firmware=DVI-I-1:edid/1920x1080.bin
in which case no other connector will be affected.
The built-in data sets are
Resolution Name
--------------------------------
1024x768 edid/1024x768.bin
1280x1024 edid/1280x1024.bin
1680x1050 edid/1680x1050.bin
1920x1080 edid/1920x1080.bin
They are ignored, if a file with the same name is available in the
/lib/firmware directory.
The built-in EDID data sets are based on standard timings that may not
apply to a particular monitor and even crash it. Ideally, EDID data of
the connected monitor should be used. They may be obtained through the
drm/cardX/cardX-<connector>/edid entry in the /sys/devices PCI directory
of a correctly working graphics adapter.
It is even possible to specify the name of an EDID data set on-the-fly
via the /sys/module interface, e.g.
echo edid/myedid.bin >/sys/module/drm_kms_helper/parameters/edid_firmware
The new screen mode is considered when the related kernel function is
called for the first time after the change. Such calls are made when the
X server is started or when the display settings dialog is opened in an
already running X server.
Signed-off-by: Carsten Emde <C.Emde@osadl.org> Signed-off-by: Dave Airlie <airlied@redhat.com>
Joonyoung Shim [Fri, 16 Mar 2012 09:47:08 +0000 (18:47 +0900)]
drm/exynos: remove module of exynos drm subdrv
The exynos drm driver has several subdrv. They each can be module but it
causes unfixed probe order of exynodr drm driver and each subdrv. It
also needs some weird codes such as exynos_drm_fbdev_reinit and
exynos_drm_mode_group_reinit. This patch can remove weird codes and
clear codes through we doesn't modularity each subdrv.
Also this removes unnecessary codes related module.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Inki Dae [Fri, 16 Mar 2012 09:47:06 +0000 (18:47 +0900)]
drm/exynos: added new funtion to get/put dma address.
this function would be used for drm based 2d acceleration driver
to get/put dma address through gem handle.
when exynos_drm_get_dma_address is called reference count of
gem object would be increased not to be released by gem close and
when exynos_drm_put_dma_address is called the reference count of
this gem object would be decreased to be released.
Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Inki Dae [Fri, 16 Mar 2012 09:47:05 +0000 (18:47 +0900)]
drm/exynos: update gem and buffer framework.
with this patch, we can allocate physically continuous or non-continuous
memory and also it creates scatterlist for iommu support so allocated
memory region can be mapped to iommu page table using scatterlist.
Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Joonyoung Shim [Fri, 16 Mar 2012 09:47:03 +0000 (18:47 +0900)]
drm/exynos: add HDMI version 1.4 support
Later Exynos series from Exynos4X12 support HDMI version 1.4. We will
distinguish to use which version via platform data. This patch supports
only default features of HDMI version 1.4(The 3D, sound and etc don't
support yet)
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Yoichi Yuasa [Thu, 15 Mar 2012 14:50:16 +0000 (14:50 +0000)]
gma500: Fix mmap frambuffer
It cannot map correctly if page fault begins from a intermediate address.
[The driver prefaults the mapping, so we need to work from the correct
base address not the faulting address otherwise the map appears offset by
the fault offset]
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org> Signed-off-by: Alan Cox <alan@linux.intel.com> Cc: stable@kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Tue, 20 Mar 2012 08:51:37 +0000 (08:51 +0000)]
Merge tag 'drm-intel-next-2012-03-01' of git://people.freedesktop.org/~danvet/drm-intel into drm-next
* tag 'drm-intel-next-2012-03-01' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Only clear the GPU domains upon a successful finish
drm/i915: reenable gmbus on gen3+ again
drm/i915: i2c: unconditionally set up gpio fallback
drm/i915: merge gmbus and gpio i2c adpater into one
drm/i915: merge struct intel_gpio into struct intel_gmbus
i2c: export bit-banging algo functions
drm/nouveau: do a better job at hiding the NIH i2c bit-banging algo
drm/i915: add dev_priv to intel_gmbus
drm/i915: Fix single msg gmbus_xfers writes
drm/i915: error_buffer->ring should be signed
drm/i915: Silence the error message from i915_wait_request()
drm/i915: use the new hdmi_force_audio enum more
drm/i915: No need to search again after retiring requests
drm/i915: Only bump refcnt on objects scheduled for eviction
drm/i915/bios: Downgrade the "signature missing" DRM_ERROR to debug
drm/i915: Ignore LVDS on hp t5745 and hp st5747 thin client
drm/i915: Fixes distorted external screen image on HP 2730p
Michel Dänzer [Wed, 14 Mar 2012 13:59:25 +0000 (14:59 +0100)]
drm/radeon: Drop radeon_gem_object_(un)pin.
Only radeon_gem_object_unpin was used anymore, in only one place.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Michel Dänzer [Wed, 14 Mar 2012 16:12:42 +0000 (17:12 +0100)]
drm/radeon: Restrict offset for legacy display engine.
The hardware only takes 27 bits for the offset, so larger offsets are
truncated, and the display shows random bits other than the intended ones.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Michel Dänzer [Wed, 14 Mar 2012 16:12:41 +0000 (17:12 +0100)]
drm/radeon: Restrict offset for legacy hardware cursor.
The hardware only takes 27 bits for the offset, so larger offsets are
truncated, and the hardware cursor shows random bits other than the intended
ones.
Cc: stable@vger.kernel.org Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Tvrtko Ursulin [Fri, 16 Mar 2012 16:22:11 +0000 (12:22 -0400)]
drm/radeon/kms: reduce probe latency on digital connectors
On a system with one HDMI and one VGA connector the latter
causes output polling to run every ten seconds. This causes
full EDID re-fetch on every poll and approx. 100ms rendering
stalls are experienced by full screen page-flipping applications.
Optimisation is to trust HPD sense on R600+ ASICs and to skip
doing these expensive probes unless HPD sense has changed.
Most of the error handling code in this function frees the buffers
kcmd_addr, kvb_addr, and kbox_addr allocated at the beginning of this
function. These two branches are changed to do the same.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Dave Airlie <airlied@redhat.com>
Julia Lawall [Sat, 17 Mar 2012 17:03:29 +0000 (18:03 +0100)]
drivers/gpu/drm/radeon/radeon_cs.c: eliminate possible double free
The function radeon_cs_parser_init is only called from two places, in
drivers/gpu/drm/radeon/radeon_cs.c and drivers/gpu/drm/radeon/r600_cs.c.
In each case, if the call fails another function is called that frees all
of the kdata and dpage information in the chunks array. So this
information should not be freed in radeon_cs_parser_init as well.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Marek Olšák [Mon, 19 Mar 2012 02:09:33 +0000 (03:09 +0100)]
drm/radeon/kms: compute GPU addresses correctly on evergreen
There are also two fixes:
- In DRAW_INDEX_2, we read idx_value, but should have read idx+1.
- When correcting SQ_VTX_CONSTANT_WORD1_0.SIZE, we should subtract
the offset.
Signed-off-by: Marek Olšák <maraeo@gmail.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Tue, 20 Mar 2012 06:59:29 +0000 (06:59 +0000)]
drm/usb: move usb support into a separate module
In order to satisfy all the various Kconfig options between
USB and DRM, we need to split the USB code out into a separate module
and export symbols to it.
This fixes build problems in -next reported by sfr.
Dave Airlie [Tue, 14 Dec 2010 21:14:24 +0000 (07:14 +1000)]
drm/udl: initial UDL driver (v4)
This is an initial drm/kms driver for the displaylink devices.
Supports fb_defio,
supports KMS dumb interface
supports 24bpp via conversion to 16bpp, hw can do this better.
supports hot unplug using new drm core features.
On an unplug, it disables connector polling, unplugs connectors
from sysfs, unplugs fbdev layer (using Kay's API), drops all the
USB device URBs, and call the drm core to unplug the device.
This driver is based in large parts on udlfb.c so I've licensed
it under GPLv2.
Dave Airlie [Mon, 20 Feb 2012 14:18:07 +0000 (14:18 +0000)]
drm: add core support for unplugging a device (v2)
Two parts to this, one is simple unplug from sysfs for the device node.
The second adds an unplugged state, if we have device opens, we
just set the unplugged state and return, if we have no device
opens we drop the drm device.
If after a lastclose we discover we are unplugged we then
drop the drm device.
v2: use an atomic for unplugged and wrap it for users,
add checks on open + mmap + ioctl entry points.
Kay Sievers [Sat, 28 Jan 2012 19:57:46 +0000 (19:57 +0000)]
udlfb: remove sysfs framebuffer device with USB .disconnect()
The USB graphics card driver delays the unregistering of the framebuffer
device to a workqueue, which breaks the userspace visible remove uevent
sequence. Recent userspace tools started to support USB graphics card
hotplug out-of-the-box and rely on proper events sent by the kernel.
The framebuffer device is a direct child of the USB interface which is
removed immediately after the USB .disconnect() callback. But the fb device
in /sys stays around until its final cleanup, at a time where all the parent
devices have been removed already.
To work around that, we remove the sysfs fb device directly in the USB
.disconnect() callback and leave only the cleanup of the internal fb
data to the delayed work.
Ville Syrjälä [Tue, 13 Mar 2012 10:35:49 +0000 (12:35 +0200)]
drm: Use a flexible array member for blob property data
The blob property data is always allocated immediately after the object
header. No need for the extra indirection when accessing it, just use
a flexible array member.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ville Syrjälä [Tue, 13 Mar 2012 10:35:48 +0000 (12:35 +0200)]
drm: Handle drm_object_get() failures
Check drm_mode_object_get() return value everywhere.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ville Syrjälä [Tue, 13 Mar 2012 10:35:47 +0000 (12:35 +0200)]
drm: Make drm_crtc_convert_{umode, to_umode} static and constify their params
drm_crtc_convert_umode() and drm_crtc_convert_to_umode() are never
used outside drm_crtc.c, so make them static. Also make the input
mode structure const for both functions.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ville Syrjälä [Tue, 13 Mar 2012 10:35:46 +0000 (12:35 +0200)]
drm: Fix drm_mode_attachmode_crtc()
Change drm_mode_attachmode_crtc() to take an "all or nothing" approach.
If an error is returned, there are no side effects visible.
Also change the function to always duplicate the mode passed in.
Also change the function to not give up when it finds the first
connector without and encoder.
A simpler approach would be to just remove the function completely as
it's unused currently.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ville Syrjälä [Tue, 13 Mar 2012 10:35:45 +0000 (12:35 +0200)]
drm: Check CRTC viewport against framebuffer size
Make sure the requested CRTC viewport fits inside the
framebuffer.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ville Syrjälä [Tue, 13 Mar 2012 10:35:44 +0000 (12:35 +0200)]
drm: Check user mode against overflows
The internal mode representation drm_display_mode uses signed data
types. When converting the user mode to internal representation,
check that the unsigned values don't overflow the signed datatypes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ville Syrjälä [Tue, 13 Mar 2012 10:35:43 +0000 (12:35 +0200)]
drm: Fix memory leak in drm_mode_setcrtc()
The mode passed to the .set_config() hook was never freed. The drivers
will make a copy of the mode, so simply free it when done.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ville Syrjälä [Tue, 13 Mar 2012 10:35:42 +0000 (12:35 +0200)]
drm: Make drm_mode_attachmode() void
drm_mode_attachmode() always returns 0. Change the return type to void.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ville Syrjälä [Tue, 13 Mar 2012 10:35:41 +0000 (12:35 +0200)]
drm: Check crtc x and y coordinates
The crtc x/y panning coordinates are stored as signed integers
internally. The user provides them as unsigned, so we should check
that the user provided values actually fit in the internal datatypes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ville Syrjälä [Tue, 13 Mar 2012 10:35:40 +0000 (12:35 +0200)]
drm: Warn if mode to umode conversion overflows the destination types
When converting from a drm_display_mode to drm_mode_modeinfo, print a
warning if the the timings values don't fit into the __u16 datatype.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
projects / mv-sheeva.git / log