Catalin Marinas [Tue, 22 Nov 2011 17:30:29 +0000 (17:30 +0000)]
ARM: LPAE: MMU setup for the 3-level page table format
This patch adds the MMU initialisation for the LPAE page table format.
The swapper_pg_dir size with LPAE is 5 rather than 4 pages. A new
proc-v7-3level.S file contains the TTB initialisation, context switch
and PTE setting code with the LPAE. The TTBRx split is based on the
PAGE_OFFSET with TTBR1 used for the kernel mappings. The 36-bit mappings
(supersections) and a few other memory types in mmu.c are conditionally
compiled.
Catalin Marinas [Tue, 22 Nov 2011 17:30:29 +0000 (17:30 +0000)]
ARM: LPAE: Page table maintenance for the 3-level format
This patch modifies the pgd/pmd/pte manipulation functions to support
the 3-level page table format. Since there is no need for an 'ext'
argument to cpu_set_pte_ext(), this patch conditionally defines a
different prototype for this function when CONFIG_ARM_LPAE.
The patch also introduces the L_PGD_SWAPPER flag to mark pgd entries
pointing to pmd tables pre-allocated in the swapper_pg_dir and avoid
trying to free them at run-time. This flag is 0 with the classic page
table format.
Catalin Marinas [Tue, 22 Nov 2011 17:30:29 +0000 (17:30 +0000)]
ARM: LPAE: Introduce the 3-level page table format definitions
This patch introduces the pgtable-3level*.h files with definitions
specific to the LPAE page table format (3 levels of page tables).
Each table is 4KB and has 512 64-bit entries. An entry can point to a
40-bit physical address. The young, write and exec software bits share
the corresponding hardware bits (negated). Other software bits use spare
bits in the PTE.
The patch also changes some variable types from unsigned long or int to
pteval_t or pgprot_t.
Will Deacon [Tue, 22 Nov 2011 17:30:28 +0000 (17:30 +0000)]
ARM: LPAE: add ISBs around MMU enabling code
Before we enable the MMU, we must ensure that the TTBR registers contain
sane values. After the MMU has been enabled, we jump to the *virtual*
address of the following function, so we also need to ensure that the
SCTLR write has taken effect.
This patch adds ISB instructions around the SCTLR write to ensure the
visibility of the above.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Catalin Marinas [Tue, 22 Nov 2011 17:30:28 +0000 (17:30 +0000)]
ARM: LPAE: Factor out classic-MMU specific code into proc-v7-2level.S
This patch modifies the proc-v7.S file so that it only contains code
shared between classic MMU and LPAE. The non-common code is factored out
into a separate file.
Catalin Marinas [Tue, 22 Nov 2011 17:30:28 +0000 (17:30 +0000)]
ARM: LPAE: Move the FSR definitions to separate files
The FSR structure is different with LPAE and this patch moves the
classic MMU specific definition to a separate fsr-2level.c file that is
included in fault.c. It also moves the fsr_fs and FSR bits to the
fault.h file.
Catalin Marinas [Tue, 22 Nov 2011 17:30:28 +0000 (17:30 +0000)]
ARM: LPAE: Move page table maintenance macros to pgtable-2level.h
The page table maintenance macros need to be duplicated between the
classic and the LPAE MMU so this patch moves those that are not common
to the pgtable-2level.h file.
Russell King [Tue, 22 Nov 2011 17:30:28 +0000 (17:30 +0000)]
ARM: pgtable: switch to use pgtable-nopud.h
Nick Piggin noted upon introducing 4level-fixup.h:
| Add a temporary "fallback" header so architectures can run with
| the 4level pagetables patch without modification. All architectures
| should be converted to use the folding headers (include/asm-generic/
| pgtable-nop?d.h) as soon as possible, and the fallback header removed.
This makes ARM compliant with this statement.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Catalin Marinas [Tue, 22 Nov 2011 17:30:27 +0000 (17:30 +0000)]
ARM: pgtable: Fix compiler warning in ioremap.c introduced by nopud
With the arch/arm code conversion to pgtable-nopud.h, the section and
supersection (un|re)map code triggers compiler warnings on UP systems.
This is caused by pmd_offset() being given a pgd_t argument rather than
a pud_t one. This patch makes the necessary conversion with the
assumption that the pud is folded into the pgd. The page table setting
code only loops over the pmd which is enough with the classic page
tables. This code is not compiled when LPAE is enabled.
Will Deacon [Wed, 23 Nov 2011 12:26:25 +0000 (12:26 +0000)]
ARM: SMP: use idmap_pgd for mapping MMU enable during secondary booting
The ARM SMP booting code allocates a temporary set of page tables
containing an identity mapping of the kernel image and provides this
to secondary CPUs for initial booting.
In reality, we only need to include the __turn_mmu_on function in the
identity mapping since the rest of the kernel is executing from virtual
addresses after this point.
This patch adds __turn_mmu_on to the .idmap.text section, allowing the
SMP booting code to use the idmap_pgd directly and not have to populate
its own set of page table.
As a result of this patch, we can make the identity_mapping_add function
static (since it is only used within mm/idmap.c) and also remove the
identity_mapping_del function. The identity map population is moved to
an early initcall so that it is setup in time for secondary CPU bringup.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Will Deacon [Wed, 23 Nov 2011 12:03:27 +0000 (12:03 +0000)]
ARM: head.S: only include __turn_mmu_on in the initial identity mapping
__create_page_tables identity maps the region of memory from
__enable_mmu to the end of __turn_mmu_on.
In preparation for including __turn_mmu_on in the .idmap.text section,
this patch modifies the identity mapping so that it only includes the
__turn_mmu_on code.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Will Deacon [Wed, 8 Jun 2011 14:53:34 +0000 (15:53 +0100)]
ARM: idmap: use idmap_pgd when setting up mm for reboot
For soft-rebooting a system, it is necessary to map the MMU-off code
with an identity mapping so that execution can continue safely once the
MMU has been switched off.
Currently, switch_mm_for_reboot takes out a 1:1 mapping from 0x0 to
TASK_SIZE during reboot in the hope that the reset code lives at a
physical address corresponding to a userspace virtual address.
This patch modifies the code so that we switch to the idmap_pgd tables,
which contain a 1:1 mapping of the cpu_reset code. This has the
advantage of only remapping the code that we need and also means we
don't need to worry about allocating a pgd from an atomic context in the
case that the physical address of the cpu_reset code aliases with the
virtual space used by the kernel.
Acked-by: Dave Martin <dave.martin@linaro.org> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Will Deacon [Tue, 15 Nov 2011 11:11:19 +0000 (11:11 +0000)]
ARM: suspend: use idmap_pgd instead of suspend_pgd
The ARM CPU suspend code requires cpu_resume_mmu to be identity mapped
in order to re-enable the MMU when coming out of suspend. Currently,
this is accomplished by maintaining a suspend_pgd with the relevant
mapping put in place at init time.
This patch replaces the use of suspend_pgd with the new idmap_pgd.
cpu_resume_mmu is placed in the .idmap.text section so that it is
included in the identity map.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Dave Martin <dave.martin@linaro.org> Tested-by: Lorenzo Pieralisi <Lorenzo.Pieralisi@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Will Deacon [Fri, 30 Sep 2011 10:43:29 +0000 (11:43 +0100)]
ARM: idmap: populate identity map pgd at init time using .init.text
When disabling and re-enabling the MMU, it is necessary to take out an
identity mapping for the code that manipulates the SCTLR in order to
avoid it disappearing from under our feet. This is useful when soft
rebooting and returning from CPU suspend.
This patch allocates a set of page tables during boot and populates them
with an identity mapping for the .idmap.text section. This means that
users of the identity map do not need to manage their own pgd and can
instead annotate their functions with __idmap or, in the case of assembly
code, place them in the correct section.
Acked-by: Dave Martin <dave.martin@linaro.org> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Tested-by: Lorenzo Pieralisi <Lorenzo.Pieralisi@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Axel Lin [Thu, 1 Dec 2011 15:24:30 +0000 (23:24 +0800)]
ARM: exynos4: Fix build error due to 'gic_bank_offset' undeclared
Fix below build error:
CC arch/arm/mach-exynos/cpu.o
arch/arm/mach-exynos/cpu.c: In function 'exynos4_init_irq':
arch/arm/mach-exynos/cpu.c:245: error: 'gic_bank_offset' undeclared (first use in this function)
arch/arm/mach-exynos/cpu.c:245: error: (Each undeclared identifier is reported only once
arch/arm/mach-exynos/cpu.c:245: error: for each function it appears in.)
arch/arm/mach-exynos/cpu.c:243: warning: unused variable 'bank_offset'
make[1]: *** [arch/arm/mach-exynos/cpu.o] Error 1
make: *** [arch/arm/mach-exynos] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The changes to omap4-common.h were moved to arch/arm/mach-omap2/common.h
and the other trivial conflicts resolved. The now empty ifdef in irqs.h
was also eliminated.
Russell King [Wed, 2 Nov 2011 14:38:07 +0000 (14:38 +0000)]
ARM: restart: remove poodle restart handler
The poodle restart handler was added in 74617fb6b8 (3593/1: Add reboot
and shutdown handlers for Zaurus handhelds), and at that time it was
necessary to deal with the RCSR register. This commit also forced all
restarts to use the 'hard' restart method.
In dc38e2ad53 (pxa: Fix RCSR handling), the RCSR handling was removed,
leaving just the forcing to use a 'hard' restart. As hard restarts are
the default (in the absense of a reboot= command line argument), this
seems pointless. In any case, Richard Purdie says:
> From what I remember that hardware either always reboots or always
> halts. I think the option was therefore left hardcoded to make it clear
> it wasn't expected to work. Later Zaurii models could do either but
> required some manual poking of registers to make it happen iirc.
>
> Regardless, you can probably clean this up as you suggest now.
So, lets remove the unnecessary interception and rely on the default
restart mode.
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 1 Nov 2011 13:16:26 +0000 (13:16 +0000)]
ARM: restart: only perform setup for restart when soft-restarting
We only need to set the system up for a soft-restart if we're going to
be doing a soft-restart. Provide a new function (soft_restart()) which
does the setup and final call for this, and make platforms use it.
Eliminate the call to setup_restart() from the default handler.
This means that platforms arch_reset() function is no longer called with
the page tables prepared for a soft-restart, and caches will still be
enabled.
Acked-by: Nicolas Pitre <nico@linaro.org> Acked-by: Will Deacon <will.deacon@arm.com> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Krzysztof Ha■asa <khc@pm.waw.pl> Acked-by: Paul Mundt <lethal@linux-sh.org> Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org> Acked-by: Wan ZongShun <mcuos.com@gmail.com> Acked-by: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 5 Nov 2011 17:38:32 +0000 (17:38 +0000)]
ARM: clps711x: consolidate irq/mm/time code into a single file
The separate files for clps711x which contain maybe one or two data
structures or functions is an inefficient use of files, and encourages
further small files as other changes happen. Collapse down these into
a single core.c file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 31 Oct 2011 14:34:31 +0000 (14:34 +0000)]
ARM: restart: remove local_irq_disable() from within arch_reset()
IRQs are already disabled by the time arch_reset() is called, so these
calls to local_irq_disable() instead arch_reset() are redundant. Remove
them.
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Nicolas Pitre <nico@linaro.org> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a handler for the VIC that is suitable for MULTI_IRQ_HANDLER
platforms. This can replace the ASM entry macros for platforms that use
the VIC.
v4: - rebase ontop of move __exception and friends to
asm/exception.h
- rework polling loop to handle as many irqs as possible in one go
v3: - simplify irq handling loop as suggested by Grant
- service interrupts from msb->lsb order
v2: - allow the handler be used for !CONFIG_OF
- use irq_domain_to_irq()
Cc: Rob Herring <robherring2@gmail.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Linus Walleij <linus.walleij@linaro.org> Tested-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Jamie Iles <jamie@jamieiles.com>
This adds a device tree binding for the VIC based on the of_irq_init()
support. This adds an irqdomain to the vic and always registers all
vics in the static vic array rather than for pm only to keep track of
the irq domain. struct irq_data::hwirq is used where appropriate rather
than runtime masking.
v3: - include linux/export.h for THIS_MODULE
v2: - use irq_domain_simple_ops
- remove stub implementation of vic_of_init for !CONFIG_OF
- Make VIC select IRQ_DOMAIN
Reviewed-by: Rob Herring <robherring2@gmail.com> Reviewed-by: Grant Likely <grant.likely@secretlab.ca> Tested-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Marc Zyngier [Tue, 6 Sep 2011 09:23:45 +0000 (10:23 +0100)]
ARM: omap2plus: convert to CONFIG_MULTI_IRQ_HANDLER
Convert the omap2plus platforms to be using CONFIG_MULTI_IRQ_HANDLER.
Each machine is modified to provide either omap2_intc_handle_irq(),
omap3_intc_handle_irq() or gic_handle_irq().
This allows for a major cleanup, removing the MULTI_OMAP setup
from the interrupt path.
Tested on both Panda and IGEPv2 (single kernel image)
Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Marc Zyngier [Tue, 6 Sep 2011 08:56:17 +0000 (09:56 +0100)]
ARM: omap2/3: Add global omap2/3_intc_handle_irq() functions
Provide the OMAP2/3 IRQ code with low level handlers that can be used
by platforms using CONFIG_MULTI_IRQ_HANDLER. Though the handlers are
written in C, the compiled code looks very similar to its assembly
counterpart (at least with my gcc 4.4.1).
Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Marc Zyngier [Tue, 6 Sep 2011 09:23:45 +0000 (10:23 +0100)]
ARM: tegra2: convert to CONFIG_MULTI_IRQ_HANDLER
Convert the tegra2 platforms to be using the gic_handle_irq
function as their primary interrupt handler.
Tested on harmony.
Cc: Colin Cross <ccross@android.com> Acked-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Marc Zyngier [Tue, 6 Sep 2011 08:23:26 +0000 (09:23 +0100)]
ARM: Make global handler and CONFIG_MULTI_IRQ_HANDLER mutually exclusive
Even when CONFIG_MULTI_IRQ_HANDLER is selected, the core code
requires the arch_irq_handler_default macro to be defined as
a fallback.
It turns out nobody is using that particular feature as both PXA
and shmobile have all their machine descriptors populated with
the interrupt handler, leaving unused code (or empty macros) in
their entry-macro.S file just to be able to compile entry-armv.S.
Make CONFIG_MULTI_IRQ_HANDLER exclusive wrt arch_irq_handler_default,
which allows to remove one test from the hot path. Also cleanup both
PXA and shmobile entry-macro.S.
Cc: Paul Mundt <lethal@linux-sh.org> Acked-by: Nicolas Pitre <nico@linaro.org> Acked-by: Eric Miao <eric.y.miao@gmail.com> Tested-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Marc Zyngier [Sat, 12 Nov 2011 16:09:49 +0000 (16:09 +0000)]
ARM: gic: allow GIC to support non-banked setups
The GIC support code is heavily using the fact that hardware
implementations are exposing banked registers. Unfortunately, it
looks like at least one GIC implementation (EXYNOS) offers both
the distributor and the CPU interfaces at different addresses,
depending on the CPU.
This problem is solved by allowing the distributor and CPU interface
addresses to be per-cpu variables for the platforms that require it.
The EXYNOS code is updated not to mess with the GIC internals while
handling interrupts, and struct gic_chip_data is back to being private.
The DT binding for the gic is updated to allow an optional "cpu-offset"
value, which is used to compute the various base addresses.
Finally, a new config option (GIC_NON_BANKED) is used to control this
feature, so the overhead is only present on kernels compiled with
support for EXYNOS.
Tested on Origen (EXYNOS4) and Panda (OMAP4).
Cc: Kukjin Kim <kgene.kim@samsung.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Linus Torvalds [Tue, 15 Nov 2011 16:48:51 +0000 (14:48 -0200)]
Merge branch 'fixes' of git://git.linaro.org/people/triad/linux-pinctrl
* 'fixes' of git://git.linaro.org/people/triad/linux-pinctrl:
pinctrl: hide subsystem from the populace
pinctrl: fix "warning: 'struct pinctrl_dev' declared inside parameter list"
Linus Torvalds [Tue, 15 Nov 2011 16:45:50 +0000 (14:45 -0200)]
Merge branch 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6
* 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6:
gpio: pca953x: propagate the errno from the chip_init functions
gpio: pca953x: remove unneeded check for chip type
gpio/omap: check return value from irq_alloc_generic_chip
gpio/omap: replace MOD_REG_BIT macro with static inline
Linus Torvalds [Tue, 15 Nov 2011 16:31:12 +0000 (14:31 -0200)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin:
blackfin: Fixup export.h includes
Blackfin: add serial TX IRQ in individual platform resource
Liu Gang [Fri, 11 Nov 2011 13:48:28 +0000 (21:48 +0800)]
fsl-rio: fix compile error
The "#include <linux/module.h>" was replaced by "#include <linux/export.h>"
in the patch "powerpc: various straight conversions from module.h --> export.h".
This will cause the following compile problem:
arch/powerpc/sysdev/fsl_rio.c: In function 'fsl_rio_mcheck_exception':
arch/powerpc/sysdev/fsl_rio.c:296: error: implicit declaration of function 'search_exception_tables'.
The file fsl_rio.c needs the declaration of function "search_exception_tables"
in the header file "linux/module.h".
Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Commit 8dc7a9c84 ("blackfin: Add export.h to files using
EXPORT_SYMBOL/THIS_MODULE") inserted some of the include statements into
sections protected by an unrelated #if CONFIG_... statement. This can cause,
depending on the configuration used, warnings like this one:
arch/blackfin/mach-bf537/boards/stamp.c:2940: warning: data definition has no type or storage class
arch/blackfin/mach-bf537/boards/stamp.c:2940: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’
arch/blackfin/mach-bf537/boards/stamp.c:2940: warning: parameter names (without types) in function declaration
This patch fixes it by moving the includes out of the #if protected sections.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Bob Liu <lliubbo@gmail.com>
Linus Torvalds [Mon, 14 Nov 2011 08:47:04 +0000 (06:47 -0200)]
Merge branch 'rmobile-fixes-for-linus' of git://github.com/pmundt/linux-sh
* 'rmobile-fixes-for-linus' of git://github.com/pmundt/linux-sh:
ARM: mach-shmobile: cpuidle single/global and last_state fixes
ARM: mach-shmobile: move helper macro PORTCR to sh_pfc.h
ARM: mach-shmobile: move helper macro PORT_xx to sh_pfc.h
ARM: mach-shmobile: move helper macro PORT_DATA_xx to sh_pfc.h
ARM: mach-shmobile: ap4evb: remove white space from end of line
ARM: mach-shmobile: clock-sh7372: remove un-necessary index
ARM: mach-shmobile: kota2: add comment out separator
ARM: mach-shmobile: sh73a0: add MMC data pin pull-up
Commit 31a3ddda166cda86d2b5111e09ba4bda5239fae6 introduced
a use after free in virtio-pci. The main issue is
that the release method signals removal of the virtio device,
while remove signals removal of the pci device.
For example, on driver removal or hot-unplug,
virtio_pci_release_dev is called before virtio_pci_remove.
We then might get a crash as virtio_pci_remove tries to use the
device freed by virtio_pci_release_dev.
We allocate/free all resources together with the
pci device, so we can leave the release method empty.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: stable@kernel.org
After commit e978aa7d7d57 ("cpuidle: Move dev->last_residency update to
driver enter routine; remove dev->last_state") setting acpi_idle_suspend
to 1 by acpi_processor_suspend() causes the ACPI cpuidle routines to
return error codes continuously, which in turn causes cpuidle to lock up
(hard).
However, acpi_idle_suspend doesn't appear to be useful for any
particular purpose (it's racy and doesn't really provide any real
protection), so it can be removed, which makes the problem go away.
Reported-and-tested-by: Tomas M. <tmezzadra@gmail.com> Reported-and-tested-by: Ferenc Wagner <wferi@niif.hu> Tested-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Axel Lin [Fri, 4 Nov 2011 12:04:41 +0000 (20:04 +0800)]
[CPUFREQ] db8500: fix build error due to undeclared i variable
The variable i is removed by commit ded8433
"[CPUFREQ] db8500: remove unneeded for loop iteration over freq_table",
but current code to print available frequencies still uses the i variable.
Thus add the i variable back to fix below buld error:
CC drivers/cpufreq/db8500-cpufreq.o
drivers/cpufreq/db8500-cpufreq.c: In function 'db8500_cpufreq_init':
drivers/cpufreq/db8500-cpufreq.c:123: error: 'i' undeclared (first use in this function)
drivers/cpufreq/db8500-cpufreq.c:123: error: (Each undeclared identifier is reported only once
drivers/cpufreq/db8500-cpufreq.c:123: error: for each function it appears in.)
make[2]: *** [drivers/cpufreq/db8500-cpufreq.o] Error 1
make[1]: *** [drivers/cpufreq] Error 2
make: *** [drivers] Error 2
This patch also fixes using uninitialized i variable as array index.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Dave Jones <davej@redhat.com>
Linus Torvalds [Sat, 12 Nov 2011 02:04:51 +0000 (00:04 -0200)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: (29 commits)
m68k/mac: Remove mac_irq_{en,dis}able() wrappers
m68k/irq: Remove obsolete support for user vector interrupt fixups
m68k/irq: Remove obsolete m68k irq framework
m68k/q40: Convert Q40/Q60 to genirq
m68k/sun3: Convert Sun3/3x to genirq
m68k/sun3: Use the kstat_irqs_cpu() wrapper
m68k/apollo: Convert Apollo to genirq
m68k/vme: Convert VME to genirq
m68k/hp300: Convert HP9000/300 and HP9000/400 to genirq
m68k/mac: Optimize interrupts using chain handlers
m68k/mac: Convert Mac to genirq
m68k/amiga: Optimize interrupts using chain handlers
m68k/amiga: Convert Amiga to genirq
m68k/amiga: Refactor amiints.c
m68k/atari: Remove code and comments about different irq types
m68k/atari: Convert Atari to genirq
m68k/irq: Add genirq support
m68k/irq: Remove obsolete IRQ_FLG_* users
m68k/irq: Rename {,__}m68k_handle_int()
m68k/irq: Add m68k_setup_irq_controller()
...
Linus Torvalds [Sat, 12 Nov 2011 02:03:50 +0000 (00:03 -0200)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] v4l2-ctrl: Send change events to all fh for auto cluster slave controls
[media] v4l2-event: Don't set sev->fh to NULL on unsubscribe
[media] v4l2-event: Remove pending events from fh event queue when unsubscribing
[media] v4l2-event: Deny subscribing with a type of V4L2_EVENT_ALL
[media] MAINTAINERS: add a maintainer for s5p-mfc driver
[media] v4l: s5p-mfc: fix reported capabilities
[media] media: vb2: reset queued list on REQBUFS(0) call
[media] media: vb2: set buffer length correctly for all buffer types
[media] media: vb2: add a check for uninitialized buffer
[media] mxl111sf: fix build warning
[media] mxl111sf: remove pointless if condition in mxl111sf_config_spi
[media] mxl111sf: check for errors after mxl111sf_write_reg in mxl111sf_idac_config
[media] mxl111sf: fix return value of mxl111sf_idac_config
[media] uvcvideo: GET_RES should only be checked for BITMAP type menu controls
Linus Torvalds [Sat, 12 Nov 2011 02:01:51 +0000 (00:01 -0200)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/kvm: Fix build failure with HV KVM and CBE
powerpc/ps3: Fix lv1_gpu_attribute hcall
powerpc/ps3: Fix PS3 repository build warnings
powerpc/ps3: irq: Remove IRQF_DISABLED
powerpc/irq: Remove IRQF_DISABLED
powerpc/numa: NUMA topology support for PowerNV
powerpc: Add System RAM to /proc/iomem
powerpc: Add KVM as module to defconfigs
powerpc/kvm: Fix build with older toolchains
powerpc, tqm5200: update tqm5200_defconfig to fit for charon board.
powerpc/5200: add support for charon board
William Douglas [Thu, 10 Nov 2011 13:50:38 +0000 (13:50 +0000)]
bma023: Add SFI translation for this device
This needed the sfi IRQ 0xFF fix to go in first. It simply plumbs in the
bma023 driver with the firmware naming of it.
Signed-off-by: William Douglas <william.douglas@intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Feng Tang [Thu, 10 Nov 2011 13:23:39 +0000 (13:23 +0000)]
vrtc: change its year offset from 1960 to 1972
Real world year equals the value in vrtc YEAR register plus an offset.
We used 1960 as the offset to make leap year consistent, but for a
device's first use, its YEAR register is 0 and the system year will
be parsed as 1960 which is not a valid UNIX time and will cause many
applications to fail mysteriously. So we use 1972 instead to fix this
issue.
Updated patch which adds a sanity check suggested by Mathias
This isn't a change in behaviour for systems, because 1972 is the one we
actually use. It's the old version in upstream which is out of sync with
all devices.
Linus Torvalds [Sat, 12 Nov 2011 01:47:06 +0000 (23:47 -0200)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: rename the option to nospace_cache
Btrfs: handle bio_add_page failure gracefully in scrub
Btrfs: fix deadlock caused by the race between relocation
Btrfs: only map pages if we know we need them when reading the space cache
Btrfs: fix orphan backref nodes
Btrfs: Abstract similar code for btrfs_block_rsv_add{, _noflush}
Btrfs: fix unreleased path in btrfs_orphan_cleanup()
Btrfs: fix no reserved space for writing out inode cache
Btrfs: fix nocow when deleting the item
Btrfs: tweak the delayed inode reservations again
Btrfs: rework error handling in btrfs_mount()
Btrfs: close devices on all error paths in open_ctree()
Btrfs: avoid null dereference and leaks when bailing from open_ctree()
Btrfs: fix subvol_name leak on error in btrfs_mount()
Btrfs: fix memory leak in btrfs_parse_early_options()
Btrfs: fix our reservations for updating an inode when completing io
Btrfs: fix oops on NULL trans handle in btrfs_truncate
btrfs: fix double-free 'tree_root' in 'btrfs_mount()'
Linus Torvalds [Sat, 12 Nov 2011 01:45:42 +0000 (23:45 -0200)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Use kmemdup rather than duplicating its implementation
ALSA: hda - Re-enable the check NO_PRESENCE misc bit
ALSA: vmaster - Free slave-links when freeing the master element
ALSA: hda - Don't add elements of other codecs to vmaster slave
ALSA: intel8x0: improve virtual environment detection
ALSA: intel8x0: move virtual environment detection code into one place
ALSA: snd_usb_audio: add Logitech HD Webcam c510 to quirk-384
ALSA: hda - fix internal mic on Dell Vostro 3500 laptop
ALSA: HDA: Remove quirk for Toshiba T110
ALSA: usb-audio - Fix the missing volume quirks at delayed init
ALSA: hda - Mute unused capture sources for Realtek codecs
ALSA: intel8x0: Improve comments for VM optimization
ASoC: Ensure we get an impedence reported for WM8958 jack detect
ASoC: Don't use wm8994->control_data when requesting IRQs
ASoC: Don't use wm8994->control_data in wm8994_readable_register()
ASoC: Update git repository URL
Linus Torvalds [Sat, 12 Nov 2011 01:43:51 +0000 (23:43 -0200)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (42 commits)
drm/radeon/kms/pm: switch to dynamically allocating clock mode array
drm/radeon/kms: optimize r600_pm_profile_init
drm/radeon/kms/pm: add a proper pm profile init function for fusion
drm/radeon/kms: remove extraneous calls to radeon_pm_compute_clocks()
drm/exynos: added padding to be 64-bit align.
drm: fix kconfig unmet dependency warning
drm: add some comments to drm_wait_vblank and drm_queue_vblank_event
drm/radeon/benchmark: signedness bug in radeon_benchmark_move()
drm: do not sleep on vblank while holding a mutex
MAINTAINERS: exynos: Add EXYNOS DRM maintainer entry
drm: try to restore previous CRTC config if mode set fails
drm/radeon/kms: make an aux failure debug only
drm: drop select of SLOW_WORK
drm: serialize access to list of debugfs files
drm/radeon/kms: fix use of vram scratch page on evergreen/ni
drm/radeon: Make sure CS mutex is held across GPU reset.
drm: Ensure string is null terminated.
vmwgfx: Only allow 64x64 cursors
vmwgfx: Initialize clip rect loop correctly in surface dirty
vmwgfx: Close screen object system
...
Linus Torvalds [Sat, 12 Nov 2011 01:37:17 +0000 (23:37 -0200)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: fix force shutdown handling in xfs_end_io
xfs: constify xfs_item_ops
xfs: Fix possible memory corruption in xfs_readlink
Shawn Guo [Thu, 10 Nov 2011 08:39:32 +0000 (16:39 +0800)]
arm/imx: fix imx6q mmc error when mounting rootfs
The following error is seen in some case when mounting rootfs from
SD/MMC cards.
Waiting for root device /dev/mmcblk0p1...
mmc1: host does not support reading read-only switch. assuming write-enable.
mmc1: new high speed SDHC card at address b368
mmcblk0: mmc1:b368 SDC 3.74 GiB
mmcblk0: p1
mmc1: Timeout waiting for hardware interrupt.
mmcblk0: error -110 transferring data, sector 3678224, nr 40, cmd response 0x900, card status 0xc00
end_request: I/O error, dev mmcblk0, sector 3678225
Buffer I/O error on device mmcblk0p1, logical block 458754
lost page write due to I/O error on mmcblk0p1
This patch fixes the problem by lowering the usdhc clock and correcting
watermark configuration.
projects / linux-beck.git / log