When a cpu enters S3 state, the FPU state is lost.
After resuming for S3, if we try to lazy restore the FPU for a process running
on the same CPU, this will result in a corrupted FPU context.
Ensure that "fpu_owner_task" is properly invalided when (re-)initializing a CPU,
so nobody will try to lazy restore a state which doesn't exist in the hardware.
Tested with a 64-bit kernel on a 4-core Ivybridge CPU with eagerfpu=off,
by doing thousands of suspend/resume cycles with 4 processes doing FPU
operations running. Without the patch, a process is killed after a
few hundreds cycles by a SIGFPE.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Cc: Duncan Laurie <dlaurie@chromium.org> Cc: Olof Johansson <olofj@chromium.org> Link: http://lkml.kernel.org/r/1354306532-1014-1-git-send-email-vpalatin@chromium.org Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- The code relies on rc_pci_fixup being called, which only happens
when CONFIG_PCI_QUIRKS is enabled, so add that to Kconfig. Omitting
this causes a booting failure with a non-obvious cause.
- Update rc_pci_fixup to set the class properly, copying the
more modern style from other places
- Correct the rc_pci_fixup comment
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I enable CONFIG_DEBUG_VIRTUAL and CONFIG_SPARSEMEM_VMEMMAP, when doing
memory hotremove, there is a kernel BUG at arch/x86/mm/physaddr.c:20.
It is caused by free_section_usemap()->virt_to_page(), virt_to_page() is
only used for kernel direct mapping address, but sparse-vmemmap uses
vmemmap address, so it is going wrong here.
PMU interrupts start at IRQ_DOVE_PMU_START, not IRQ_DOVE_PMU_START + 1.
Fix the condition. (It may have been less likely to occur had the code
been written "if (irq >= IRQ_DOVE_PMU_START" which imho is the easier
to understand notation, and matches the normal way of thinking about
these things.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the acknowledgement of PMU interrupts on Dove: some Dove hardware
has not been sensibly designed so that interrupts can be handled in a
race free manner. The PMU is one such instance.
The pending (aka 'cause') register is a bunch of RW bits, meaning that
these bits can be both cleared and set by software (confirmed on the
Armada-510 on the cubox.)
Hardware sets the appropriate bit when an interrupt is asserted, and
software is required to clear the bits which are to be processed. If
we write ~(1 << bit), then we end up asserting every other interrupt
except the one we're processing. So, we need to do a read-modify-write
cycle to clear the asserted bit.
However, any interrupts which occur in the middle of this cycle will
also be written back as zero, which will also clear the new interrupts.
The upshot of this is: there is _no_ way to safely clear down interrupts
in this register (and other similarly behaving interrupt pending
registers on this device.) The patch below at least stops us creating
new interrupts.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modules, in particular oprofile (and possibly other similar tools)
need kernel_stack_pointer(), so export it using EXPORT_SYMBOL_GPL().
Cc: Yang Wei <wei.yang@windriver.com> Cc: Robert Richter <robert.richter@amd.com> Cc: Jun Zhang <jun.zhang@intel.com> Link: http://lkml.kernel.org/r/20120912135059.GZ8285@erda.amd.com Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Cc: Robert Richter <rric@kernel.org> Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com> Cc: Philip Müller <philm@manjaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The channel switch command for 6000 series devices
is larger than the maximum inline command size of
320 bytes. The command is therefore refused with a
warning. Fix this by allocating the command and
using the NOCOPY mechanism.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This bug was found by VittGam.
https://bugzilla.kernel.org/show_bug.cgi?id=43255
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
read_persistent_clock uses a global variable, use a spinlock to
ensure non-atomic updates to the variable don't overlap and cause
time to move backwards.
Signed-off-by: Colin Cross <ccross@android.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The EEH core is talking with the PCI device driver to determine the
action (purely reset, or PCI device removal). During the period, the
driver might be unloaded and in turn causes kernel crash as follows:
The patch increases the reference of the corresponding driver modules
while EEH core does the negotiation with PCI device driver so that the
corresponding driver modules can't be unloaded during the period and
we're safe to refer the callbacks.
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[ herton: backported for 3.5, adjusted driver assignments, return 0
instead of NULL, assume dev is not NULL ] Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 4.4 GCC on MIPS no longer recognizes the "h" constraint,
leading to this build failure:
CC lib/mpi/generic_mpih-mul1.o
lib/mpi/generic_mpih-mul1.c: In function 'mpihelp_mul_1':
lib/mpi/generic_mpih-mul1.c:50:3: error: impossible constraint in 'asm'
This patch updates MPI with the latest umul_ppm implementations for MIPS.
The driver relies on the generic write implementation but did not call
generic close.
Note that the call to kill the read urb is not redundant, as mct_u232
uses an interrupt urb from the second port as the read urb and that
generic close therefore fails to kill it.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
cmd was freed in pn533_dep_link_up regardless of
pn533_send_cmd_frame_async return code. Cmd is passed as argument to
pn533_in_dep_link_up_complete callback and should be freed there.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On hosts without the XSAVE support unprivileged local user can trigger
oops similar to the one below by setting X86_CR4_OSXSAVE bit in guest
cr4 register using KVM_SET_SREGS ioctl and later issuing KVM_RUN
ioctl.
QEMU first retrieves the supported features via KVM_GET_SUPPORTED_CPUID
and then sets them later. So guest's X86_FEATURE_XSAVE should be masked
out on hosts without X86_FEATURE_XSAVE, making kvm_set_cr4 with
X86_CR4_OSXSAVE fail. Userspaces that allow specifying guest cpuid with
X86_FEATURE_XSAVE even on hosts that do not support it, might be
susceptible to this attack from inside the guest as well.
Allow setting X86_CR4_OSXSAVE bit only if host has XSAVE support.
Sometimes, warnings about ioctls to partition happen often enough that they
form majority of the warnings in the kernel log and users complain. In some
cases warnings are about ioctls such as SG_IO so it's not good to get rid of
the warnings completely as they can ease debugging of userspace problems
when ioctl is refused.
Since I have seen warnings from lots of commands, including some proprietary
userspace applications, I don't think disallowing the ioctls for processes
with CAP_SYS_RAWIO will happen in the near future if ever. So lets just
stop warning for processes with CAP_SYS_RAWIO for which ioctl is allowed.
Acked-by: Paolo Bonzini <pbonzini@redhat.com> CC: Paolo Bonzini <pbonzini@redhat.com> CC: James Bottomley <JBottomley@parallels.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk> Cc: satoru takeuchi <satoru.takeuchi@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The delayed work function int_in_work() may call usb_reset_device()
and thus, indirectly, the driver's pre_reset method. Trying to
cancel the work synchronously in that situation would deadlock.
Fix by avoiding cancel_work_sync() in the pre_reset method.
If the reset was NOT initiated by int_in_work() this might cause
int_in_work() to run after the post_reset method, with urb_int_in
already resubmitted, so handle that case gracefully.
Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_pm_qos_add_request() can return 0, 1, or a negative error code,
therefore the correct error test is "if (error < 0)." Checking just for
non-zero return code leads to erroneous setting of the req->dev pointer
to NULL, which then leads to a repeated call to
dev_pm_qos_add_ancestor_request() in st1232_ts_irq_handler(). This in turn
leads to an Oops, when the I2C host adapter is unloaded and reloaded again
because of the inconsistent state of its QoS request list.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a signal handler is executed on altstack and another signal comes,
we will end up with rt_sigreturn() on return from the second handler
getting -EPERM from do_sigaltstack(). It's perfectly OK, since we
are not asking to change the settings; in fact, they couldn't have been
changed during the second handler execution exactly because we'd been
on altstack all along. 64bit sigreturn on sparc treats any error from
do_sigaltstack() as "SIGSEGV now"; we need to switch to the same semantics
we are using on other architectures.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 09e05d48 introduced a wait for transaction commit into
journal_unmap_buffer() in the case we are truncating a buffer undergoing commit
in the page stradding i_size on a filesystem with blocksize < pagesize. Sadly
we forgot to drop buffer lock before waiting for transaction commit and thus
deadlock is possible when kjournald wants to lock the buffer.
Fix the problem by dropping the buffer lock before waiting for transaction
commit. Since we are still holding page lock (and that is OK), buffer cannot
disappear under us.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set in the rx_ifindex to pass the correct interface index in the case of a
message timeout detection. Usually the rx_ifindex value is set at receive
time. But when no CAN frame has been received the RX_TIMEOUT notification
did not contain a valid value.
Reported-by: Andre Naujoks <nautsch2@googlemail.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The skb->tstamp is set to the hardware timestamp when available in the USB
urb message. This leads to user visible timestamps which contain the 'uptime'
of the USB adapter - and not the usual system generated timestamp.
Fix this wrong assignment by applying the available hardware timestamp to the
skb_shared_hwtstamps data structure - which is intended for this purpose.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Intel 82855PM host bridge / Mobility FireGL 9000 RV250 combination
in an (outdated) ThinkPad T41 needs AGPMode 1 for suspend/resume (under
KMS, that is). So add a quirk for it.
(Change R250 to RV250 in comment for preceding quirk too.)
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check whether the IBSS is active and can be removed should be
performed before deinitializing the fields used for the check/search.
Otherwise, the configured BSS will not be found and removed properly.
To make it more clear for the future, rename sdata->u.ibss to the
local pointer ifibss which is used within the checks.
Dave Jones reported a bug with futex_lock_pi() that his trinity test
exposed. Sometime between queue_me() and taking the q.lock_ptr, the
lock_ptr became NULL, resulting in a crash.
While futex_wake() is careful to not call wake_futex() on futex_q's with
a pi_state or an rt_waiter (which are either waiting for a
futex_unlock_pi() or a PI futex_requeue()), futex_wake_op() and
futex_requeue() do not perform the same test.
Update futex_wake_op() and futex_requeue() to test for q.pi_state and
q.rt_waiter and abort with -EINVAL if detected. To ensure any future
breakage is caught, add a WARN() to wake_futex() if the same condition
is true.
This fix has seen 3 hours of testing with "trinity -c futex" on an
x86_64 VM with 4 CPUS.
[akpm@linux-foundation.org: tidy up the WARN()] Signed-off-by: Darren Hart <dvhart@linux.intel.com> Reported-by: Dave Jones <davej@redat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: John Kacur <jkacur@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Request based dm attempts to re-run the request queue off the
request completion path. If used with a driver that potentially does
end_io from its request_fn, we could deadlock trying to recurse
back into request dispatch. Fix this by punting the request queue
run to kblockd.
Tested to fix a quickly reproducible deadlock in such a scenario.
When a write to a replacement device completes, we carefully
and correctly found the rdev that the write actually went to
and the blithely called rdev_dec_pending on the primary rdev,
even if this write was to the replacement.
This means that any writes to an array while a replacement
was ongoing would cause the nr_pending count for the primary
device to go negative, so it could never be removed.
This bug has been present since replacement was introduced in
3.3, so it is suitable for any -stable kernel since then.
jffs2_write_begin() first acquires the page lock, then f->sem. This
causes an AB-BA deadlock with jffs2_garbage_collect_live(), which first
acquires f->sem, then the page lock:
We fix this by restructuring jffs2_write_begin() to take f->sem before
the page lock. However, we make sure that f->sem is not held when
calling jffs2_reserve_space(), as this is not permitted by the locking
rules.
The deadlock above was observed multiple times on an SoC with a dual
ARMv7 (Cortex-A9), running the long-term 3.4.11 kernel; it occurred
when using scp to copy files from a host system to the ARM target
system. The fix was heavily tested on the same target system.
The pointer returned by kzalloc should be tested for NULL
to avoid potential NULL pointer dereference later. Incorrect
pointer was being tested for NULL. Bug introduced by commit fbcf62a3
(mtd: physmap_of: move parse_obsolete_partitions to become separate
parser).
This patch fixes this bug.
On Thu, 2012-11-01 at 16:45 -0700, Michel Lespinasse wrote:
> Looking at the arch/parisc/kernel/sys_parisc.c implementation of
> get_shared_area(), I do have a concern though. The function basically
> ignores the pgoff argument, so that if one creates a shared mapping of
> pages 0-N of a file, and then a separate shared mapping of pages 1-N
> of that same file, both will have the same cache offset for their
> starting address.
>
> This looks like this would create obvious aliasing issues. Am I
> misreading this ? I can't understand how this could work good enough
> to be undetected, so there must be something I'm missing here ???
This turns out to be correct and we need to pay attention to the pgoff as
well as the address when creating the virtual address for the area.
Fortunately, the bug is rarely triggered as most applications which use pgoff
tend to use large values (git being the primary one, and it uses pgoff in
multiples of 16MB) which are larger than our cache coherency modulus, so the
problem isn't often seen in practise.
Reported-by: Michel Lespinasse <walken@google.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If this array is not cleared, the jack related code later might
fail to create "Internal Speaker Phantom Jack" on Dell Inspiron 3420 and
Dell Vostro 2420.
Commit 88a8516a2128 (ALSA: usbaudio: implement USB autosuspend) added
autosuspend code to all files making up the snd-usb-audio driver.
However, midi.c is part of snd-usb-lib and is also used by other
drivers, not all of which support autosuspend. Thus, calls to
usb_autopm_get_interface() could fail, and this unexpected error would
result in the MIDI output being completely unusable.
Make it work by ignoring the error that is expected with drivers that do
not support autosuspend.
Reported-by: Colin Fletcher <colin.m.fletcher@googlemail.com> Reported-by: Devin Venable <venable.devin@gmail.com> Reported-by: Dr Nick Bailey <nicholas.bailey@glasgow.ac.uk> Reported-by: Jannis Achstetter <jannis_achstetter@web.de> Reported-by: Rui Nuno Capela <rncbc@rncbc.org> Cc: Oliver Neukum <oliver@neukum.org> Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SATA MICROCODE DOWNALOAD fails on isci driver. After receiving Register
Device to Host (FIS 0x34) frame Initiator resets phy.
In the frame handler routine response (FIS 0x34) was copied into wrong
buffer and upper layer did not receive any answer which resulted in
timeout and reset.
This patch corrects this bug.
Signed-off-by: Maciej Patelczyk <maciej.patelczyk@intel.com> Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported by Tim Shepard:
I was seeing sporadic failures (wedgeups), and the majority of those
failures I saw printed the printouts in mwifiex_cmd_timeout_func with
cmd = 0xe5 which is CMD_802_11_HS_CFG_ENH. When this happens, two
minutes later I get notified that the rtcwake thread is blocked, like
this:
INFO: task rtcwake:3495 blocked for more than 120 seconds.
To get the hung thread unblocked we wake up the cmd wait queue and
cancel the ioctl.
Reported-by: Tim Shepard <shep@laptop.org> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is an ISY IWL 2000. Probably a clone of Belkin F7D1102 050d:1102.
Its FCC ID is the same.
Signed-off-by: Albert Pool <albertpool@solcon.nl> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building for Athlon/Duron/K7 results in the following build error,
arch/x86/boot/compressed/eboot.o: In function `__constant_memcpy3d':
eboot.c:(.text+0x385): undefined reference to `_mmx_memcpy'
arch/x86/boot/compressed/eboot.o: In function `efi_main':
eboot.c:(.text+0x1a22): undefined reference to `_mmx_memcpy'
because the boot stub code doesn't link with the kernel proper, and
therefore doesn't have access to the 3DNow version of memcpy. So,
follow the example of misc.c and #undef memcpy so that we use the
version provided by misc.c.
See https://bugzilla.kernel.org/show_bug.cgi?id=50391
Reported-by: Al Viro <viro@zeniv.linux.org.uk> Reported-by: Ryan Underwood <nemesis@icequake.net> Cc: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 32 bit the stack address provided by kernel_stack_pointer() may
point to an invalid range causing NULL pointer access or page faults
while in NMI (see trace below). This happens if called in softirq
context and if the stack is empty. The address at ®s->sp is then
out of range.
Fixing this by checking if regs and ®s->sp are in the same stack
context. Otherwise return the previous stack pointer stored in struct
thread_info. If that address is invalid too, return address of regs.
V2:
* add comments to kernel_stack_pointer()
* always return a valid stack address by falling back to the address
of regs
Reported-by: Yang Wei <wei.yang@windriver.com> Signed-off-by: Robert Richter <robert.richter@amd.com> Link: http://lkml.kernel.org/r/20120912135059.GZ8285@erda.amd.com Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Cc: Jun Zhang <jun.zhang@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With gcc 4.7.x, the following warning is issued as the routine that sets
the array has the possibility of not initializing the values:
CC [M] drivers/net/wireless/rtlwifi/rtl8192se/phy.o
drivers/net/wireless/rtlwifi/rtl8192se/phy.c: In function ‘rtl92s_phy_set_txpower’:
drivers/net/wireless/rtlwifi/rtl8192se/phy.c:1268:23: warning: ‘ofdmpowerLevel[0]’ may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is to change use of "0x%08x" in favour of "%p" as per ../Documentation/printk-formats.txt,
which also takes care about the following warning during compilation time:
drivers/scsi/aha152x.c: In function ‘get_command’:
drivers/scsi/aha152x.c:2987: warning: cast from pointer to integer of different size
We don't use "dev" any more after 07ec747a5f ("libsas: remove
ata_port.lock management duties from lldds") and it causes a compile
warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Xiangliang Yu <yuxiangl@marvell.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/leds/leds-lp5521.c: In function `lp5521_load_program':
drivers/leds/leds-lp5521.c:214:21: warning: `mode' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-lp5521.c: In function `lp5521_probe':
drivers/leds/leds-lp5521.c:788:5: warning: `buf' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-lp5521.c:740:6: warning: `ret' may be used uninitialized in this function [-Wuninitialized]
These are real problems if lp5521_read() returns an error. When that
happens we should handle it, instead of ignoring it or doing a bitwise
OR with all the other error codes and continuing.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Milo <Milo.Kim@ti.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Bryan Wu <bryan.wu@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC [M] sound/usb/caiaq/device.o
sound/usb/caiaq/device.c: In function ‘snd_probe’:
sound/usb/caiaq/device.c:500:16: warning: ‘card’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
If remote device sends bogus RFC option with invalid length,
undefined options values are used. Fix this by using defaults when
remote misbehaves.
This also fixes the following warning reported by gcc 4.7.0:
net/bluetooth/l2cap_core.c: In function 'l2cap_config_rsp':
net/bluetooth/l2cap_core.c:3302:13: warning: 'rfc.max_pdu_size' may be used uninitialized in this function [-Wmaybe-uninitialized]
net/bluetooth/l2cap_core.c:3266:24: note: 'rfc.max_pdu_size' was declared here
net/bluetooth/l2cap_core.c:3298:25: warning: 'rfc.monitor_timeout' may be used uninitialized in this function [-Wmaybe-uninitialized]
net/bluetooth/l2cap_core.c:3266:24: note: 'rfc.monitor_timeout' was declared here
net/bluetooth/l2cap_core.c:3297:25: warning: 'rfc.retrans_timeout' may be used uninitialized in this function [-Wmaybe-uninitialized]
net/bluetooth/l2cap_core.c:3266:24: note: 'rfc.retrans_timeout' was declared here
net/bluetooth/l2cap_core.c:3295:2: warning: 'rfc.mode' may be used uninitialized in this function [-Wmaybe-uninitialized]
net/bluetooth/l2cap_core.c:3266:24: note: 'rfc.mode' was declared here
For some reason the declaration of ceph_con_get() and
ceph_con_put() did not get deleted in this commit: d59315ca libceph: drop ceph_con_get/put helpers and nref member
Clean that up.
Signed-off-by: Alex Elder <elder@inktank.com> Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As Russell has pointed out, that commit isn't fixing
Software Flow Control at all, and it actually makes
it even more broken.
It was agreed to revert this commit and use Russell's
latest UART patches instead.
Signed-off-by: Felipe Balbi <balbi@ti.com> Cc: Russell King <linux@arm.linux.org.uk> Acked-by: Tony Lindgren <tony@atomide.com> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are systems where video module known to work fine regardless
of broken _DOD and ignoring returned value here doesn't cause
any issues later. This should fix brightness controls on some laptops.
A pgoff_t is defined (by default) to have type (unsigned long). On
architectures such as i686 that's a 32-bit type. The ceph address
space code was attempting to produce 64 bit offsets by shifting a
page's index by PAGE_CACHE_SHIFT, but the result was not what was
desired because the shift occurred before the result got promoted
to 64 bits.
Fix this by converting all uses of page->index used in this way to
use the page_offset() macro, which ensures the 64-bit result has the
intended value.
This fixes http://tracker.newdream.net/issues/3112
Reported-by: Mohamed Pakkeer <pakkeer.mohideen@realimage.com> Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ceph_on_in_msg_alloc() method drops con->mutex while it allocates a
message. If that races with a timeout that resends a zillion messages and
resets the connection, and the ->alloc_msg() method returns a NULL message,
it will call ceph_msg_put(NULL) and BUG.
Fix by only calling put if msg is non-NULL.
Fixes http://tracker.newdream.net/issues/3142
Signed-off-by: Sage Weil <sage@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ceph_fault() is unable to queue work after a delay, it sets the
BACKOFF connection flag so con_work() will attempt to do so.
In con_work(), when BACKOFF is set, if queue_delayed_work() doesn't
result in newly-queued work, it simply ignores this condition and
proceeds as if no backoff delay were desired. There are two
problems with this--one of which is a bug.
The first problem is simply that the intended behavior is to back
off, and if we aren't able queue the work item to run after a delay
we're not doing that.
The only reason queue_delayed_work() won't queue work is if the
provided work item is already queued. In the messenger, this
means that con_work() is already scheduled to be run again. So
if we simply set the BACKOFF flag again when this occurs, we know
the next con_work() call will again attempt to hold off activity
on the connection until after the delay.
The second problem--the bug--is a leak of a reference count. If
queue_delayed_work() returns 0 in con_work(), con->ops->put() drops
the connection reference held on entry to con_work(). However,
processing is (was) allowed to continue, and at the end of the
function a second con->ops->put() is called.
This patch fixes both problems.
Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In write_partial_msg_pages(), pages need to be kmapped in order to
perform a CRC-32c calculation on them. As an artifact of the way
this code used to be structured, the kunmap() call was separated
from the kmap() call and both were done conditionally. But the
conditions under which the kmap() and kunmap() calls were made
differed, so there was a chance a kunmap() call would be done on a
page that had not been mapped.
The symptom of this was tripping a BUG() in kunmap_high() when
pkmap_count[nr] became 0.
Reported-by: Bryan K. Wright <bryan@virginia.edu> Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because the Ceph client messenger uses a non-blocking connect, it is
possible for the sending of the client banner to race with the
arrival of the banner sent by the peer.
When ceph_sock_state_change() notices the connect has completed, it
schedules work to process the socket via con_work(). During this
time the peer is writing its banner, and arrival of the peer banner
races with con_work().
If con_work() calls try_read() before the peer banner arrives, there
is nothing for it to do, after which con_work() calls try_write() to
send the client's banner. In this case Ceph's protocol negotiation
can complete succesfully.
The server-side messenger immediately sends its banner and addresses
after accepting a connect request, *before* actually attempting to
read or verify the banner from the client. As a result, it is
possible for the banner from the server to arrive before con_work()
calls try_read(). If that happens, try_read() will read the banner
and prepare protocol negotiation info via prepare_write_connect().
prepare_write_connect() calls con_out_kvec_reset(), which discards
the as-yet-unsent client banner. Next, con_work() calls
try_write(), which sends the protocol negotiation info rather than
the banner that the peer is expecting.
The result is that the peer sees an invalid banner, and the client
reports "negotiation failed".
Fix this by moving con_out_kvec_reset() out of
prepare_write_connect() to its callers at all locations except the
one where the banner might still need to be sent.
[elder@inktak.com: added note about server-side behavior]
Signed-off-by: Jim Schutt <jaschut@sandia.gov> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The debugfs directory includes the cluster fsid and our unique global_id.
We need to delay the initialization of the debug entry until we have
learned both the fsid and our global_id from the monitor or else the
second client can't create its debugfs entry and will fail (and multiple
client instances aren't properly reflected in debugfs).
We drop the lock when calling the ->alloc_msg() con op, which means
we need to (a) not clobber con->in_msg without the mutex held, and (b)
we need to verify that we are still in the OPEN state when we retake
it to avoid causing any mayhem. If the state does change, -EAGAIN
will get us back to con_work() and loop.
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function's calling convention is very limiting. In particular,
we can't return any error other than ENOMEM (and only implicitly),
which is a problem (see next patch).
Instead, return an normal 0 or error code, and make the skip a pointer
output parameter. Drop the useless in_hdr argument (we have the con
pointer).
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ceph_fault() function takes the con mutex, so we should avoid
dropping it before calling it. This fixes a potential race with
another thread calling ceph_con_close(), or _open(), or similar (we
don't reverify con->state after retaking the lock).
Add annotation so that lockdep realizes we will drop the mutex before
returning.
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We drop the con mutex when delivering a message. When we retake the
lock, we need to verify we are still in the OPEN state before
preparing to read the next tag, or else we risk stepping on a
connection that has been closed.
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revoke all mon_client messages when we shut down the old connection.
This is mostly moot since we are re-using the same ceph_connection,
but it is cleaner.
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a simple set of 6 enumerated values for the socket states (CON_STATE_*)
and use those instead of the state bits. All of the con->state checks are
now under the protection of the con mutex, so this is safe. It also
simplifies many of the state checks because we can check for anything other
than the expected state instead of various bits for races we can think of.
This appears to hold up well to stress testing both with and without socket
failure injection on the server side.
Signed-off-by: Sage Weil <sage@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We exponentially back off when we encounter connection errors. If several
errors accumulate, we will eventually wait ages before even trying to
reconnect.
Fix this by resetting the backoff counter after a successful negotiation/
connection with the remote node. Fixes ceph issue #2802.
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Yehuda Sadeh <yehuda@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take the con mutex while we are initiating a ceph open. This is necessary
because the may have previously been in use and then closed, which could
result in a racing workqueue running con_work().
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Yehuda Sadeh <yehuda@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, we were opportunistically initializing the bio_iter if it
appeared to be uninitialized in the middle of the read path. The problem
is that a sequence like:
- start reading message
- initialize bio_iter
- read half a message
- messenger fault, reconnect
- restart reading message
- ** bio_iter now non-NULL, not reinitialized **
- read past end of bio, crash
Instead, initialize the bio_iter unconditionally when we allocate/claim
the message for read.
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com> Reviewed-by: Yehuda Sadeh <yehuda@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The linger op registration (i.e., watch) modifies the object state. As
such, the OSD will reply with success if it has already applied without
doing the associated side-effects (setting up the watch session state).
If we lose the ACK and resubmit, we will see success but the watch will not
be correctly registered and we won't get notifies.
To fix this, always resubmit the linger op with a new tid. We accomplish
this by re-registering as a linger (i.e., 'registered') if we are not yet
registered. Then the second loop will treat this just like a normal
case of re-registering.
This mirrors a similar fix on the userland ceph.git, commit 5dd68b95, and
ceph bug #2796.
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com> Reviewed-by: Yehuda Sadeh <yehuda@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log