ipv6: don't accept node local multicast traffic from the wire
Erik Hugne's errata proposal (Errata ID: 3480) to RFC4291 has been
verified: http://www.rfc-editor.org/errata_search.php?eid=3480
We have to check for pkt_type and loopback flag because either the
packets are allowed to travel over the loopback interface (in which case
pkt_type is PACKET_HOST and IFF_LOOPBACK flag is set) or they travel
over a non-loopback interface back to us (in which case PACKET_TYPE is
PACKET_LOOPBACK and IFF_LOOPBACK flag is not set).
Cc: Erik Hugne <erik.hugne@ericsson.com> Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Mirko Lindner [Tue, 26 Mar 2013 06:38:42 +0000 (06:38 +0000)]
sky2: Threshold for Pause Packet is set wrong
The sky2 driver sets the Rx Upper Threshold for Pause Packet generation to a
wrong value which leads to only 2kB of RAM remaining space. This can lead to
Rx overflow errors even with activated flow-control.
Fix: We should increase the value to 8192/8
Signed-off-by: Mirko Lindner <mlindner@marvell.com> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Mirko Lindner [Tue, 26 Mar 2013 06:38:35 +0000 (06:38 +0000)]
sky2: Receive Overflows not counted
The sky2 driver doesn't count the Receive Overflows because the MAC
interrupt for this event is not set in the MAC's interrupt mask.
The MAC's interrupt mask is set only for Transmit FIFO Underruns.
Fix: The correct setting should be (GM_IS_TX_FF_UR | GM_IS_RX_FF_OR)
Otherwise the Receive Overflow event will not generate any interrupt.
The Receive Overflow interrupt is handled correctly
Signed-off-by: Mirko Lindner <mlindner@marvell.com> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 28 Mar 2013 21:42:36 +0000 (17:42 -0400)]
Merge branch 'wireless'
John W. Linville says:
====================
Please excuse this larger-than-I-would-like pull request intended
for the 3.9 stream. There are a number of late-breaking fixes,
including a revert...
Regarding the mac80211 bits, Johannes says:
"I have two tracing fixes (one from Vladimir), two fixes for P2P device
crashes, a fix for a BSS memory leak/lost update problem and a fix from
Ben for a scanning issue in mac80211. It's a little on the large side
because one of the P2P device problems required a bit much locking work,
but I've run through all the different scenarios (wext/nl80211,
p2p-device/station interface, ifdown/rfkill) to verify locking with
lockdep."
As for the iwlwifi bits, Johannes says:
"I have three little fixes to the driver from Emmanuel. One addresses a
small bug Ben Hutchings found during the stable review process and two
address some warnings in the driver when RF-Kill is asserted."
Along with those...
Avinash Patil fixes an mwifiex bug cause by failing to process a sleep
command due to bad SKB manipulation when going into power saving mode.
Colin Ian King avoids a null pointer dereference in iwl4965.
Dan Williams officially announces that he has dropped maintainership
of the libertas driver.
Iestyn C. Elfick adds a work-around to avoid b43 DMA transmision
sequence error that would lead to a device reset.
Luis R. Rodriguez avoids an ath9k warning by not queueing a work item
while going to suspend mode.
Rafał Miłecki provides a pair of b43 N-PHY fixes related to RSSI
calibration.
Finally, I revert "brcmsmac: support 4313iPA" because it has been
reported in many places to cause problems with the already supported
4313ePA devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 27 Mar 2013 18:28:41 +0000 (18:28 +0000)]
aoe: reserve enough headroom on skbs
Some network drivers use a non default hard_header_len
Transmitted skb should take into account dev->hard_header_len, or risk
crashes or expensive reallocations.
In the case of aoe, lets reserve MAX_HEADER bytes.
David reported a crash in defxx driver, solved by this patch.
Reported-by: David Oostdyk <daveo@ll.mit.edu> Tested-by: David Oostdyk <daveo@ll.mit.edu> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Ed Cashin <ecashin@coraid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 27 Mar 2013 18:08:42 +0000 (14:08 -0400)]
Merge branch 'fixes-for-3.9' of git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
here's a patch series for net for the v3.9 release cycle. Fengguang Wu found
two problems with the sja1000 drivers:
A macro in the SH architecture collides with one in the sja1000 driver. I
created a minimal patch suited for stable, only changing this particular
define. (Once net is merged back to net-next, I'll post a patch to uniformly
use a SJA1000_ prefix for the sja100 private defines.) If you prefer, I can
squash both patches together.
Fengguang further noticed that the peak pcmcia driver will not compile on archs
without ioport support. I created a patch to limit the driver to archs which
select HAS_IOPORT in Kconfig.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 27 Mar 2013 18:07:04 +0000 (14:07 -0400)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
1) Initialize the satype field in key_notify_policy_flush(),
this was left uninitialized. From Nicolas Dichtel.
2) The sequence number difference for replay notifications
was misscalculated on ESN sequence number wrap. We need
a separate replay notify function for esn.
3) Fix an off by one in the esn replay notify function.
From Mathias Krause.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit the hardware's reported firmware string length (max 255 bytes) to
stay inside the driver's firmware string length (32 bytes). On overflow,
truncate the formatted firmware string instead of potentially overwriting
portions of the tg3 struct.
sch: make htb_rate_cfg and functions around that generic
adds little regression.
Before:
# tc qdisc add dev eth0 root handle 1: htb default ffff
# tc class add dev eth0 classid 1:ffff htb rate 5Gbit
# tc -s class show dev eth0
class htb 1:ffff root prio 0 rate 5000Mbit ceil 5000Mbit burst 625b cburst
625b
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
rate 0bit 0pps backlog 0b 0p requeues 0
lended: 0 borrowed: 0 giants: 0
tokens: 31 ctokens: 31
After:
# tc qdisc add dev eth0 root handle 1: htb default ffff
# tc class add dev eth0 classid 1:ffff htb rate 5Gbit
# tc -s class show dev eth0
class htb 1:ffff root prio 0 rate 1544Mbit ceil 1544Mbit burst 625b cburst
625b
Sent 5073 bytes 41 pkt (dropped 0, overlimits 0 requeues 0)
rate 1976bit 2pps backlog 0b 0p requeues 0
lended: 41 borrowed: 0 giants: 0
tokens: 1802 ctokens: 1802
This probably due to lost u64 cast of rate parameter in
psched_ratecfg_precompute() (net/sched/sch_generic.c).
Signed-off-by: Sergey Popovich <popovich_sergei@mail.ru> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N [Wed, 27 Mar 2013 04:42:00 +0000 (04:42 +0000)]
drivers: net: ethernet: davinci_emac: use netif_wake_queue() while restarting tx queue
To restart tx queue use netif_wake_queue() intead of netif_start_queue()
so that net schedule will restart transmission immediately which will
increase network performance while doing huge data transfers.
Reported-by: Dan Franke <dan.franke@schneider-electric.com> Suggested-by: Sriramakrishnan A G <srk@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N [Wed, 27 Mar 2013 04:41:59 +0000 (04:41 +0000)]
drivers: net: ethernet: cpsw: use netif_wake_queue() while restarting tx queue
To restart tx queue use netif_wake_queue() intead of netif_start_queue()
so that net schedule will restart transmission immediately which will
increase network performance while doing huge data transfers.
Reported-by: Dan Franke <dan.franke@schneider-electric.com> Suggested-by: Sriramakrishnan A G <srk@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Wed, 27 Mar 2013 03:22:45 +0000 (03:22 +0000)]
rtnetlink: fix error return code in rtnl_link_fill()
Fix to return a negative error code from the error handling case
instead of 0(possible overwrite to 0 by ops->fill_xstats call),
as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 27 Mar 2013 16:25:11 +0000 (09:25 -0700)]
Merge tag 'iommu-fixes-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"Here are some fixes which have collected since Linux v3.9-rc1.
The most important one fixes a long-standing regressen which make
re-hotplugged devices unusable when AMD IOMMU is used.
The other patches fix build issues (build regression on OMAP and a
section mismatch). One patch just removes a duplicate header include."
* tag 'iommu-fixes-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Make sure dma_ops are set for hotplug devices
x86, io_apic: remove duplicated include from irq_remapping.c
iommu: OMAP: build only on OMAP2+
amd_iommu_init: remove __init from amd_iommu_erratum_746_workaround
Al Viro [Wed, 27 Mar 2013 15:20:30 +0000 (15:20 +0000)]
vfs/splice: Fix missed checks in new __kernel_write() helper
Commit 06ae43f34bcc ("Don't bother with redoing rw_verify_area() from
default_file_splice_from()") lost the checks to test existence of the
write/aio_write methods. My apologies ;-/
Eventually, we want that in fs/splice.c side of things (no point
repeating it for every buffer, after all), but for now this is the
obvious minimal fix.
Reported-by: Dave Jones <davej@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rafał Miłecki [Wed, 27 Mar 2013 07:37:08 +0000 (08:37 +0100)]
b43: N-PHY: use more bits for offset in RSSI calibration
When calculating "offset" for final RSSI calibration we're using numbers
bigger than s8 can hold. We have for example:
offset[j] = 232 - poll_results[j];
formula. If poll_results[j] is small enough (it usually is) we treat
number's bit as a sign bit. For example 232 - 1 becomes:
0xE8 - 0x1 = 0xE7, which is not 231 but -25.
il4965_rs_initialize_lq checks to see if sta is null, however, before that
check il4965_rs_use_green dereferences sta when intializing use_green.
Avoid a potential null pointer dereference error by only calling
il4965_rs_use_green after we are sure sta is not null.
Smatch analysis:
drivers/net/wireless/iwlegacy/4965-rs.c:2160 il4965_rs_initialize_lq() warn:
variable dereferenced before check 'sta' (see line 2155)
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: avoid queueing hw check work when suspended
The following issue was reported.
WARNING: at net/mac80211/util.c:599 ieee80211_can_queue_work.isra.7+0x32/0x40 [mac80211]()
Hardware name: iMac12,1
queueing ieee80211 work while going to suspend
Pid: 0, comm: swapper/0 Tainted: PF O 3.8.2-206.fc18.x86_64 #1
Call Trace: Mar 16 09:39:17 Parags-iMac kernel: [ 3993.642992] <IRQ>
[<ffffffff8105e61f>] warn_slowpath_common+0x7f/0xc0
[<ffffffffa0581420>] ? ath_start_rx_poll+0x70/0x70 [ath9k]
<ffffffff8105e716>] warn_slowpath_fmt+0x46/0x50
[<ffffffffa045b542>] ieee80211_can_queue_work.isra.7+0x32/0x40
Fix this by avoiding to queue the work if our device has
already been marked as suspended or stopped.
Reported-by: Parag Warudkar <parag.lkml@gmail.com> Tested-by: Parag Warudkar <parag.lkml@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Iestyn C. Elfick [Wed, 20 Mar 2013 19:02:31 +0000 (14:02 -0500)]
b43: A fix for DMA transmission sequence errors
Intermittently, b43 will report "Out of order TX status report on DMA ring".
When this happens, the driver must be reset before communication can resume.
The cause of the problem is believed to be an error in the closed-source
firmware; however, all versions of the firmware are affected.
This change uses the observation that the expected status is always 2 less
than the observed value, and supplies a fake status report to skip one
header/data pair.
Not all devices suffer from this problem, but it can occur several times
per second under heavy load. As each occurence kills the unmodified driver,
this patch makes if possible for the affected devices to function. The patch
logs only the first instance of the reset operation to prevent spamming
the logs.
Tested-by: Chris Vine <chris@cvine.freeserve.co.uk> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Tue, 19 Mar 2013 06:52:48 +0000 (07:52 +0100)]
b43: N-PHY: increase initial value of "mind" in RSSI calibration
We're using "mind" variable to find the VCM that got the best polling
results. For each VCM we calculte "currd" which is compared to the
"mind". For PHY rev3+ "currd" gets values around 14k-40k. Looking for a
value smaller than 40 makes no sense, so increase the initial value.
Thias patch fixes a define conflict between the SH architecture and the sja1000
driver:
drivers/net/can/sja1000/sja1000.h:59:0: warning:
"REG_SR" redefined [enabled by default]
arch/sh/include/asm/ptrace_32.h:25:0: note:
this is the location of the previous definition
A SJA1000_ prefix is added to the offending sja1000 define only, to make a
minimal patch suited for stable. A later patch will add a SJA1000_ prefix to
all defines in sja1000.h.
Christoph Paasch [Wed, 20 Mar 2013 08:59:46 +0000 (08:59 +0000)]
e1000e: Add missing dma_mapping_error-call in e1000_alloc_jumbo_rx_buffers
After dma_map_page, dma_mapping_error must be called. It seems safe to
not free the skb/page allocated in this function, as the skb/page can be
reused later.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Christoph Paasch [Wed, 20 Mar 2013 08:59:41 +0000 (08:59 +0000)]
ixgb: Add missing dma_mapping_error-call in ixgb_alloc_rx_buffers
After dma_map_single, dma_mapping_error must be called. It seems safe to
not free the skb allocated in this function, as the skb can be reused
later.
Additionally this patch fixes one coding-style error.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Christoph Paasch [Wed, 20 Mar 2013 08:59:35 +0000 (08:59 +0000)]
e1000: ethtool: Add missing dma_mapping_error-call in e1000_setup_desc_rings
After dma_map_single, dma_mapping_error must be called.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Joerg Roedel [Tue, 26 Mar 2013 21:48:23 +0000 (22:48 +0100)]
iommu/amd: Make sure dma_ops are set for hotplug devices
There is a bug introduced with commit 27c2127 that causes
devices which are hot unplugged and then hot-replugged to
not have per-device dma_ops set. This causes these devices
to not function correctly. Fixed with this patch.
Cc: stable@vger.kernel.org Reported-by: Andreas Degert <andreas.degert@googlemail.com> Signed-off-by: Joerg Roedel <joro@8bytes.org>
Linus Torvalds [Wed, 27 Mar 2013 00:42:55 +0000 (17:42 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"stable fodder; assorted deadlock fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vt: synchronize_rcu() under spinlock is not nice...
Nest rename_lock inside vfsmount_lock
Don't bother with redoing rw_verify_area() from default_file_splice_from()
Al Viro [Wed, 27 Mar 2013 00:30:17 +0000 (20:30 -0400)]
vt: synchronize_rcu() under spinlock is not nice...
vcs_poll_data_free() calls unregister_vt_notifier(), which calls
atomic_notifier_chain_unregister(), which calls synchronize_rcu().
Do it *after* we'd dropped ->f_lock.
Cc: stable@vger.kernel.org (all kernels since 2.6.37) Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Tue, 26 Mar 2013 22:25:57 +0000 (18:25 -0400)]
Nest rename_lock inside vfsmount_lock
... lest we get livelocks between path_is_under() and d_path() and friends.
The thing is, wrt fairness lglocks are more similar to rwsems than to rwlocks;
it is possible to have thread B spin on attempt to take lock shared while thread
A is already holding it shared, if B is on lower-numbered CPU than A and there's
a thread C spinning on attempt to take the same lock exclusive.
As the result, we need consistent ordering between vfsmount_lock (lglock) and
rename_lock (seq_lock), even though everything that takes both is going to take
vfsmount_lock only shared.
Spotted-by: Brad Spengler <spender@grsecurity.net> Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
1) Always increment IPV4 ID field in encapsulated GSO packets, even
when DF is set. Regression fix from Pravin B Shelar.
2) Fix per-net subsystem initialization in netfilter conntrack,
otherwise we may access dynamically allocated memory before it is
actually allocated. From Gao Feng.
3) Fix DMA buffer lengths in iwl3945 driver, from Stanislaw Gruszka.
4) Fix race between submission of sync vs async commands in mwifiex
driver, from Amitkumar Karwar.
5) Add missing cancel of command timer in mwifiex driver, from Bing
Zhao.
6) Missing SKB free in rtlwifi USB driver, from Jussi Kivilinna.
7) Thermal layer tries to use a genetlink multicast string that is
longer than the 16 character limit. Fix it and add a BUG check to
prevent this kind of thing from happening in the future.
From Masatake YAMATO.
8) Fix many bugs in the handling of the teardown of L2TP connections,
UDP encapsulation instances, and sockets. From Tom Parkin.
9) Missing socket release in IRDA, from Kees Cook.
10) Fix fec driver modular build, from Fabio Estevam.
11) Erroneous use of kfree() instead of free_netdev() in lantiq_etop,
from Wei Yongjun.
12) Fix bugs in handling of queue numbers and steering rules in mlx4
driver, from Moshe Lazer, Hadar Hen Zion, and Or Gerlitz.
13) Some FOO_DIAG_MAX constants were defined off by one, fix from Andrey
Vagin.
14) TCP segmentation deferral is unintentionally done too strongly,
breaking ACK clocking. Fix from Eric Dumazet.
15) net_enable_timestamp() can legitimately be invoked from software
interrupts, and in a way that is safe, so remove the WARN_ON().
Also from Eric Dumazet.
16) Fix use after free in VLANs, from Cong Wang.
17) Fix TCP slow start retransmit storms after SACK reneging, from
Yuchung Cheng.
18) Unix socket release should mark a socket dead before NULL'ing out
sock->sk, otherwise we can race. Fix from Paul Moore.
19) IPV6 addrconf code can try to free static memory, from Hong Zhiguo.
20) Fix register mis-programming, NULL pointer derefs, and wrong PHC
clock frequency in IGB driver. From Lior LevyAlex Williamson, Jiri
Benc, and Jeff Kirsher.
21) skb->ip_summed logic in pch_gbe driver is reversed, breaking packet
forwarding. Fix from Veaceslav Falico.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
ipv4: Fix ip-header identification for gso packets.
bonding: remove already created master sysfs link on failure
af_unix: dont send SCM_CREDENTIAL when dest socket is NULL
pch_gbe: fix ip_summed checksum reporting on rx
igb: fix PHC stopping on max freq
igb: make sensor info static
igb: SR-IOV init reordering
igb: Fix null pointer dereference
igb: fix i350 anti spoofing config
ixgbevf: don't release the soft entries
ipv6: fix bad free of addrconf_init_net
unix: fix a race condition in unix_release()
tcp: undo spurious timeout after SACK reneging
bnx2x: fix assignment of signed expression to unsigned variable
bridge: fix crash when set mac address of br interface
8021q: fix a potential use-after-free
net: remove a WARN_ON() in net_enable_timestamp()
tcp: preserve ACK clocking in TSO
net: fix *_DIAG_MAX constants
net/mlx4_core: Disallow releasing VF QPs which have steering rules
...
Linus Torvalds [Tue, 26 Mar 2013 21:23:45 +0000 (14:23 -0700)]
Merge tag 'nfs-for-3.9-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Fix an NFSv4 idmapper regression
- Fix an Oops in the pNFS blocks client
- Fix up various issues with pNFS layoutcommit
- Ensure correct read ordering of variables in
rpc_wake_up_task_queue_locked
* tag 'nfs-for-3.9-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: Add barriers to ensure read ordering in rpc_wake_up_task_queue_locked
NFSv4.1: Add a helper pnfs_commit_and_return_layout
NFSv4.1: Always clear the NFS_INO_LAYOUTCOMMIT in layoutreturn
NFSv4.1: Fix a race in pNFS layoutcommit
pnfs-block: removing DM device maybe cause oops when call dev_remove
NFSv4: Fix the string length returned by the idmapper
Pravin B Shelar [Sun, 24 Mar 2013 17:36:29 +0000 (17:36 +0000)]
ipv4: Fix ip-header identification for gso packets.
ip-header id needs to be incremented even if IP_DF flag is set.
This behaviour was changed in commit 490ab08127cebc25e3a26
(IP_GRE: Fix IP-Identification).
Following patch fixes it so that identification is always
incremented.
Reported-by: Cong Wang <amwang@redhat.com> Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dingtianhong [Mon, 25 Mar 2013 17:02:04 +0000 (17:02 +0000)]
af_unix: dont send SCM_CREDENTIAL when dest socket is NULL
SCM_SCREDENTIALS should apply to write() syscalls only either source or destination
socket asserted SOCK_PASSCRED. The original implememtation in maybe_add_creds is wrong,
and breaks several LSB testcases ( i.e. /tset/LSB.os/netowkr/recvfrom/T.recvfrom).
Origionally-authored-by: Karel Srot <ksrot@redhat.com> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 26 Mar 2013 16:21:31 +0000 (12:21 -0400)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net
Jeff Kirsher says:
====================
This series contains updates to ixgbevf and igb.
The ixgbevf calls to pci_disable_msix() and to free the msix_entries
memory should not occur if device open fails. Instead they should be
called during device driver removal to balance with the call to
pci_enable_msix() and the call to allocate msix_entries memory
during the device probe and driver load.
The remaining 4 of 5 igb patches are simple 1-3 line patches to fix
several issues such as possible null pointer dereference, PHC stopping
on max frequency, make sensor info static and SR-IOV initialization
reordering.
The remaining igb patch to fix anti-spoofing config fixes a problem
in i350 where anti spoofing configuration was written into a wrong
register.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Veaceslav Falico [Mon, 25 Mar 2013 22:26:21 +0000 (22:26 +0000)]
pch_gbe: fix ip_summed checksum reporting on rx
skb->ip_summed should be CHECKSUM_UNNECESSARY when the driver reports that
checksums were correct and CHECKSUM_NONE in any other case. They're
currently placed vice versa, which breaks the forwarding scenario. Fix it
by placing them as described above.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc [Wed, 20 Mar 2013 09:06:34 +0000 (09:06 +0000)]
igb: fix PHC stopping on max freq
For 82576 MAC type, max_adj is reported as 1000000000 ppb. However, if
this value is passed to igb_ptp_adjfreq_82576, incvalue overflows out of
INCVALUE_82576_MASK, resulting in setting of zero TIMINCA.incvalue, stopping
the PHC (instead of going at twice the nominal speed).
Fix the advertised max_adj value to the largest value hardware can handle.
As there is no min_adj value available (-max_adj is used instead), this will
also prevent stopping the clock intentionally. It's probably not a big deal,
other igb MAC types don't support stopping the clock, either.
Signed-off-by: Jiri Benc <jbenc@redhat.com> Acked-by: Matthew Vick <matthew.vick@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alex Williamson [Wed, 13 Mar 2013 15:50:29 +0000 (15:50 +0000)]
igb: SR-IOV init reordering
igb is ineffective at setting a lower total VFs because:
int pci_sriov_set_totalvfs(struct pci_dev *dev, u16 numvfs)
{
...
/* Shouldn't change if VFs already enabled */
if (dev->sriov->ctrl & PCI_SRIOV_CTRL_VFE)
return -EBUSY;
Swap init ordering.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Acked-by: Greg Rose <gregory.v.rose@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alex Williamson [Wed, 13 Mar 2013 15:50:24 +0000 (15:50 +0000)]
igb: Fix null pointer dereference
The max_vfs= option has always been self limiting to the number of VFs
supported by the device. fa44f2f1 added SR-IOV configuration via
sysfs, but in the process broke this self correction factor. The
failing path is:
This leaves vfs_allocated_count = 7 and vf_data = NULL, so we bomb out
when igb_probe finally calls igb_reset. It seems like a really bad
idea, and somewhat pointless, to set vfs_allocated_count separate from
vf_data, but limiting max_vfs is enough to avoid the null pointer.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Acked-by: Greg Rose <gregory.v.rose@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Lior Levy [Tue, 12 Mar 2013 15:49:32 +0000 (15:49 +0000)]
igb: fix i350 anti spoofing config
Fix a problem in i350 where anti spoofing configuration was written into a
wrong register.
Signed-off-by: Lior Levy <lior.levy@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
xunleer [Tue, 5 Mar 2013 07:44:20 +0000 (07:44 +0000)]
ixgbevf: don't release the soft entries
When the ixgbevf driver is opened the request to allocate MSIX irq
vectors may fail. In that case the driver will call ixgbevf_down()
which will call ixgbevf_irq_disable() to clear the HW interrupt
registers and calls synchronize_irq() using the msix_entries pointer in
the adapter structure. However, when the function to request the MSIX
irq vectors failed it had already freed the msix_entries which causes
an OOPs from using the NULL pointer in synchronize_irq().
The calls to pci_disable_msix() and to free the msix_entries memory
should not occur if device open fails. Instead they should be called
during device driver removal to balance with the call to
pci_enable_msix() and the call to allocate msix_entries memory
during the device probe and driver load.
Signed-off-by: Li Xun <xunleer.li@huawei.com> Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Tested-by: Sibai Li <sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Linus Torvalds [Tue, 26 Mar 2013 01:03:34 +0000 (18:03 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"A single bugfix which prevents that a non functional timer device is
selected to provide the fallback device, which is supposed to serve
timer interrupts on behalf of non functional devices ..."
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevents: Don't allow dummy broadcast timers
Avinash Patil [Thu, 21 Mar 2013 00:56:23 +0000 (17:56 -0700)]
mwifiex: reset skb->data after processing PCIe sleep confirm cmd respose
This patch is a bug fix for an issue wherein power save was not
working for PCIe. This happens because for processing power save
sleep confirm command we pull skb so that skb->data points ahead
of interface header. We use same skb to get other cmda responses
as well. So if we don't push skb after processing cmd response,
it results into reduction in skb->len and finally skb->len reaches
zero. This causes failure in processing sleep command response.
Fix this by pushing skb by INTF_HEADER_LEN at the end of command
response processing.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Paul Moore [Mon, 25 Mar 2013 03:18:33 +0000 (03:18 +0000)]
unix: fix a race condition in unix_release()
As reported by Jan, and others over the past few years, there is a
race condition caused by unix_release setting the sock->sk pointer
to NULL before properly marking the socket as dead/orphaned. This
can cause a problem with the LSM hook security_unix_may_send() if
there is another socket attempting to write to this partially
released socket in between when sock->sk is set to NULL and it is
marked as dead/orphaned. This patch fixes this by only setting
sock->sk to NULL after the socket has been marked as dead; I also
take the opportunity to make unix_release_sock() a void function
as it only ever returned 0/success.
Dave, I think this one should go on the -stable pile.
Special thanks to Jan for coming up with a reproducer for this
problem.
Reported-by: Jan Stancek <jan.stancek@gmail.com> Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 25 Mar 2013 16:44:39 +0000 (09:44 -0700)]
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma fixes from Roland Dreier:
"Small batch of InfiniBand/RDMA fixes for 3.9:
- Fix for TX lockup in IPoIB
- QLogic -> Intel update for qib driver
- Small static checker fix for qib
- Fix error path return value in cxgb4"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/qib: change QLogic to Intel
IB/ipath: Silence a static checker warning
IPoIB: Fix send lockup due to missed TX completion
RDMA/cxgb4: Fix error return code in create_qp()
Linus Torvalds [Mon, 25 Mar 2013 16:26:10 +0000 (09:26 -0700)]
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC bug fixes from Arnd Bergmann:
"Four patches for arm-soc this week:
- Kevin Hilman is no longer reachable under his previous email
address. He submitted the patch earlier, but nobody felt
responsible to pick it up.
- One Tegra fix for an incorect register address in device tree.
- IMX multiplatform support exposes a configuration option that leads
to unbootable kernels on all other machines and that needs to
depend on that platform.
- A nontrivial bug fix for the setup of the mxs video output."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: update email address for Kevin Hilman
ARM: tegra: fix register address of slink controller
ARM: imx: add dependency check for DEBUG_IMX_UART_PORT
ARM: video: mxs: Fix mxsfb misconfiguring VDCTRL0
Linus Torvalds [Mon, 25 Mar 2013 16:25:12 +0000 (09:25 -0700)]
Merge branch 'for-3.9' of git://linux-nfs.org/~bfields/linux
Pull nfsd bugfixes from J Bruce Fields:
"Fixes for a couple mistakes in the new DRC code. And thanks to Kent
Overstreet for noticing we've been sync'ing the wrong range on stable
writes since 3.8."
* 'for-3.9' of git://linux-nfs.org/~bfields/linux:
nfsd: fix bad offset use
nfsd: fix startup order in nfsd_reply_cache_init
nfsd: only unhash DRC entries that are in the hashtable
Trond Myklebust [Mon, 25 Mar 2013 15:23:40 +0000 (11:23 -0400)]
SUNRPC: Add barriers to ensure read ordering in rpc_wake_up_task_queue_locked
We need to be careful when testing task->tk_waitqueue in
rpc_wake_up_task_queue_locked, because it can be changed while we
are holding the queue->lock.
By adding appropriate memory barriers, we can ensure that it is safe to
test task->tk_waitqueue for equality if the RPC_TASK_QUEUED bit is set.
Linus Torvalds [Mon, 25 Mar 2013 09:57:32 +0000 (02:57 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Exynos and Intel fixes.
The intel fixes are fairly straightforward, mostly reverts due to bugs
found. The exynos one is a big larger since they found some issues
with the G2D engine and iommu interaction, and needed to verify the
operations a lot better than they were previously, otherwise a user
app can just crash the kernel with an iommu fault."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
Revert "drm/i915: write backlight harder"
drm/i915: don't disable the power well yet
Revert "drm/i915: set TRANSCODER_EDP even earlier"
drm/exynos: Check g2d cmd list for g2d restrictions
drm/exynos: Add a new function to get gem buffer size
drm/exynos: Deal with g2d buffer info more efficiently
drm/exynos: Clean up some G2D codes for readability
drm/exynos: Fix G2D core malfunctioning issue
drm/exynos: clear node object type at gem unmap
drm/exynos: Fix error routine to getting dma addr.
drm/exynos: Replaced kzalloc & memcpy with kmemdup
drm/exynos: fimd: calculate the correct address offset
drm/exynos: Make mixer_check_timing static
drm/exynos: modify the compatible string for exynos fimd
Mathias Krause [Wed, 20 Mar 2013 21:59:11 +0000 (22:59 +0100)]
xfrm: Fix esn sequence number diff calculation in xfrm_replay_notify_esn()
Commit 0017c0b "xfrm: Fix replay notification for esn." is off by one
for the sequence number wrapped case as UINT_MAX is 0xffffffff, not
0x100000000. ;)
Just calculate the diff like done everywhere else in the file.
Dave Airlie [Mon, 25 Mar 2013 02:20:00 +0000 (12:20 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into HEAD
Daniel writes:
"Just three revert/disable by default patches, one of them cc: stable
(since the offending commit was cc: stable, too)."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
Revert "drm/i915: write backlight harder"
drm/i915: don't disable the power well yet
Revert "drm/i915: set TRANSCODER_EDP even earlier"
Dave Airlie [Mon, 25 Mar 2013 02:19:10 +0000 (12:19 +1000)]
Merge branch 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into HEAD
Inki writes:
Includes bug fixes and code cleanups.
And it considers some restrictions to G2D hardware.
With this, the malfunction and page fault issues to g2d driver
would be fixed.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: Check g2d cmd list for g2d restrictions
drm/exynos: Add a new function to get gem buffer size
drm/exynos: Deal with g2d buffer info more efficiently
drm/exynos: Clean up some G2D codes for readability
drm/exynos: Fix G2D core malfunctioning issue
drm/exynos: clear node object type at gem unmap
drm/exynos: Fix error routine to getting dma addr.
drm/exynos: Replaced kzalloc & memcpy with kmemdup
drm/exynos: fimd: calculate the correct address offset
drm/exynos: Make mixer_check_timing static
drm/exynos: modify the compatible string for exynos fimd
Yuchung Cheng [Sun, 24 Mar 2013 10:42:25 +0000 (10:42 +0000)]
tcp: undo spurious timeout after SACK reneging
On SACK reneging the sender immediately retransmits and forces a
timeout but disables Eifel (undo). If the (buggy) receiver does not
drop any packet this can trigger a false slow-start retransmit storm
driven by the ACKs of the original packets. This can be detected with
undo and TCP timestamps.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Amit Mehta [Sat, 23 Mar 2013 20:10:25 +0000 (20:10 +0000)]
bnx2x: fix assignment of signed expression to unsigned variable
fix for incorrect assignment of signed expression to unsigned variable.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com> Acked-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hong zhi guo [Sat, 23 Mar 2013 02:27:50 +0000 (02:27 +0000)]
bridge: fix crash when set mac address of br interface
When I tried to set mac address of a bridge interface to a mac
address which already learned on this bridge, I got system hang.
The cause is straight forward: function br_fdb_change_mac_address
calls fdb_insert with NULL source nbp. Then an fdb lookup is
performed. If an fdb entry is found and it's local, it's OK. But
if it's not local, source is dereferenced for printk without NULL
check.
Signed-off-by: Hong Zhiguo <honkiko@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Fri, 22 Mar 2013 19:14:07 +0000 (19:14 +0000)]
8021q: fix a potential use-after-free
vlan_vid_del() could possibly free ->vlan_info after a RCU grace
period, however, we may still refer to the freed memory area
by 'grp' pointer. Found by code inspection.
This patch moves vlan_vid_del() as behind as possible.
Cc: Patrick McHardy <kaber@trash.net> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Cong Wang <amwang@redhat.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Its safe at this point because the parent socket owns a reference
on the netstamp_needed, so we cant have a 0 -> 1 transition, which
requires to lock a mutex.
Instead of refining the check, lets remove it, as all known callers
are safe. If it ever changes in the future, static_key_slow_inc()
will complain anyway.
Reported-by: Laurent Chavey <chavey@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 24 Mar 2013 17:11:29 +0000 (10:11 -0700)]
Merge tag 'pinctrl-fixes-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"Here are a few pinctrl fixes for the v3.9 rc series:
- Usecount bounds checking so we do not go below zero on mux
usecounts.
- Loop range checking in GPIO ranges in the DT range parser.
- Proper print in debugfs for pinconf state.
- Fix compilation bug in generic pinconf code.
- Minor bugfixes to abx500 and mvebu drivers."
* tag 'pinctrl-fixes-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinmux: forbid mux_usecount to be set at UINT_MAX
pinctrl: mvebu: fix checking for SoC specific controls
pinctrl: generic: Fix compilation error
pinctrl: Print the correct information in debugfs pinconf-state file
pinctrl: abx500: Fix checking if pin use AlternateFunction register
gpio: fix wrong checking condition for gpio range
Linus Torvalds [Sun, 24 Mar 2013 17:10:34 +0000 (10:10 -0700)]
Merge branch 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"A collection of minor fixes, more EFI variables paranoia
(anti-bricking) plus the ability to disable the pstore either as a
runtime default or completely, due to bricking concerns."
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efivars: Fix check for CONFIG_EFI_VARS_PSTORE_DEFAULT_DISABLE
x86, microcode_intel_early: Mark apply_microcode_early() as cpuinit
efivars: Handle duplicate names from get_next_variable()
efivars: explicitly calculate length of VariableName
efivars: Add module parameter to disable use as a pstore backend
efivars: Allow disabling use as a pstore backend
x86-32, microcode_intel_early: Fix crash with CONFIG_DEBUG_VIRTUAL
x86-64: Fix the failure case in copy_user_handle_tail()
fixed a regression in 3.6-rc kernels for which we've never figured out
the exact root cause. But some further inspection of the backlight
code reveals that it's seriously lacking locking. And especially the
asle backlight update is know to get fired (through some smm magic)
when writing specific backlight control registers. So the possibility
of suffering from races is rather real.
Until those races are fixed I don't think it makes sense to try
further hacks. Which sucks a bit, but sometimes that's how it is :(
References: http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg18788.html
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47941 Tested-by: Takashi Iwai <tiwai@suse.de> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: stable@vger.kernel.org (the reverted commit was cc: stable, too) Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 22 Mar 2013 17:07:23 +0000 (14:07 -0300)]
drm/i915: don't disable the power well yet
We're still not 100% ready to disable the power well, so don't disable
it for now. When we disable it we break the audio driver (because some
of the audio registers are on the power well) and machines with eDP on
port D (because it doesn't use TRANSCODER_EDP).
Also, instead of just reverting the code, add a Kernel option to let
us disable it if we want. This will allow us to keep developing and
testing the feature while it's not enabled.
This fixes problems caused by the following commit:
commit d6dd9eb1d96d2b7345fe4664066c2b7ed86da898
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jan 29 16:35:20 2013 -0200
drm/i915: dynamic Haswell display power well support
References: http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg18788.html Cc: Takashi Iwai <tiwai@suse.de> Cc: Mengdong Lin <mengdong.lin@intel.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
His machine has eDP on port D (usual desktop all-in-on setup), which
intel_dp.c identifies as an eDP panel, but the hsw ddi code
mishandles.
Closer inspection of the code reveals that haswell_crtc_mode_set also
checks intel_encoder_is_pch_edp when setting is_cpu_edp. On haswell
that doesn't make much sense (since there's no edp on the pch), but
what this function _really_ checks is whether that edp connector is on
port A or port D. It's just that on ilk-ivb port D was on the pch ...
So that explains why this seemingly innocent change killed eDP on port
D. Furthermore it looks like everything else accidentally works, since
we've never enabled eDP on port D support for hsw intentionally (e.g.
we still register the HDMI output for port D in that case).
But in retrospective I also don't like that this leaks highly platform
specific details into common code, and the reason is that the drm
vblank layer sucks. So instead I think we should:
- move the cpu_transcoder into the dynamic pipe_config tracking (once
that's merged).
- fix up the drm vblank layer to finally deal with kms crtc objects
instead of int pipes.
v2: Pimp commit message with the better diagnosis as discussed with
Paulo on irc.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Takashi Iwai <tiwai@suse.de> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Greear [Wed, 20 Mar 2013 00:50:50 +0000 (17:50 -0700)]
mac80211: Don't restart sta-timer if not associated.
I found another crash when deleting lots of virtual stations
in a congested environment. I think the problem is that
the ieee80211_mlme_notify_scan_completed could call
ieee80211_restart_sta_timer for a stopped interface
that was about to be deleted.
With the following patch I am unable to reproduce the
crash.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[move check, also make the same change in mesh] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 19 Mar 2013 14:04:07 +0000 (15:04 +0100)]
cfg80211: always check for scan end on P2P device
If a P2P device wdev is removed while it has a scan, then the
scan completion might crash later as it is already freed by
that time. To avoid the crash always check the scan completion
when the P2P device is being removed for some reason. If the
driver already canceled it, don't want and free it, otherwise
warn and leak it to avoid later crashes.
In order to do this, locking needs to be changed away from the
rdev mutex (which can't always be guaranteed). For now, use
the sched_scan_mtx instead, I'll rename it to just scan_mtx in
a later patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull SCSI target fixes from Nicholas Bellinger:
"These are mostly minor fixes this time around. The iscsi-target CHAP
big-endian bugfix and bump FD_MAX_SECTORS=2048 default patch to allow
1MB sized I/Os for FILEIO backends on >= v3.5 code are both CC'ed to
stable.
Also, there is a persistent reservations regression that has recently
been reported for >= v3.8.x code, that is currently being tracked down
for v3.9."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/pscsi: Reject cross page boundary case in pscsi_map_sg
target/file: Bump FD_MAX_SECTORS to 2048 to handle 1M sized I/Os
tcm_vhost: Flush vhost_work in vhost_scsi_flush()
tcm_vhost: Add missed lock in vhost_scsi_clear_endpoint()
target: fix possible memory leak in core_tpg_register()
target/iscsi: Fix mutual CHAP auth on big-endian arches
target_core_sbc: use noop for SYNCHRONIZE_CACHE
Linus Torvalds [Sat, 23 Mar 2013 22:49:49 +0000 (15:49 -0700)]
Merge tag 'md-3.9-fixes' of git://neil.brown.name/md
Pull md fixes from NeilBrown:
"A few bugfixes for md
- recent regressions in raid5
- recent regressions in dmraid
- a few instances of CONFIG_MULTICORE_RAID456 linger
Several tagged for -stable"
* tag 'md-3.9-fixes' of git://neil.brown.name/md:
md: remove CONFIG_MULTICORE_RAID456 entirely
md/raid5: ensure sync and DISCARD don't happen at the same time.
MD: Prevent sysfs operations on uninitialized kobjects
MD RAID5: Avoid accessing gendisk or queue structs when not available
md/raid5: schedule_construction should abort if nothing to do.
Linus Torvalds [Sat, 23 Mar 2013 19:33:36 +0000 (12:33 -0700)]
Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata updates from Jeff Garzik:
"Simple stuff. See one-line summaries."
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_samsung_cf: use module_platform_driver_probe()
[libata] Avoid specialized TLA's in ZPODD's Kconfig
libata-acpi.c: fix copy and paste mistake in ata_acpi_register_power_resource
sata_fsl: Remove redundant NULL check before kfree
ahci: Add Device IDs for Intel Wellsburg PCH
ata_piix: Add MODULE_PARM_DESC to prefer_ms_hyperv
Linus Torvalds [Sat, 23 Mar 2013 19:32:14 +0000 (12:32 -0700)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"One bugfix for the tegra driver. Two updates regarding email
addresses and MAINTAINERS which I like to have up-to-date so people
can be reached immediately. While we are here, there is on PCI_ID
addition."
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: add maintainer entry for atmel i2c driver
i2c: Fix my e-mail address in drivers and documentation
i2c: iSMT: add Intel Avoton DeviceIDs
i2c: tegra: check the clk_prepare_enable() return value
Linus Torvalds [Sat, 23 Mar 2013 19:30:39 +0000 (12:30 -0700)]
Merge git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
"Fix a boot issues and correct the AcpiMmioSel bitmask in the
sp5100_tco watchdog device driver"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: sp5100_tco: Set the AcpiMmioSel bitmask value to 1 instead of 2
watchdog: sp5100_tco: Remove code that may cause a boot failure
Torsten Duwe [Sat, 23 Mar 2013 14:39:34 +0000 (15:39 +0100)]
KMS: fix EDID detailed timing frame rate
When KMS has parsed an EDID "detailed timing", it leaves the frame rate
zeroed. Consecutive (debug-) output of that mode thus yields 0 for
vsync. This simple fix also speeds up future invocations of
drm_mode_vrefresh().
While it is debatable whether this qualifies as a -stable fix I'd apply
it for consistency's sake; drm_helper_probe_single_connector_modes()
does the same thing already for all probed modes.
Torsten Duwe [Sat, 23 Mar 2013 14:38:22 +0000 (15:38 +0100)]
KMS: fix EDID detailed timing vsync parsing
EDID spreads some values across multiple bytes; bit-fiddling is needed
to retrieve these. The current code to parse "detailed timings" has a
cut&paste error that results in a vsync offset of at most 15 lines
instead of 63.
See
http://en.wikipedia.org/wiki/EDID
and in the "EDID Detailed Timing Descriptor" see bytes 10+11 show why
that needs to be a left shift.
Dan Carpenter [Mon, 18 Mar 2013 20:25:26 +0000 (20:25 +0000)]
IB/ipath: Silence a static checker warning
I have a static checker which complains that 0x255 is too high for
the "dev->opstats[opcode]" array. It turns out that the hardware
has already validated the opcode at this point so it can't actually
overflow.
However, silencing the warning is good and this matches how the
opcode is treated in qib_ib_rcv() as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Mike Marciniszyn [Tue, 26 Feb 2013 15:46:27 +0000 (15:46 +0000)]
IPoIB: Fix send lockup due to missed TX completion
Commit f0dc117abdfa ("IPoIB: Fix TX queue lockup with mixed UD/CM
traffic") attempts to solve an issue where unprocessed UD send
completions can deadlock the netdev.
The patch doesn't fully resolve the issue because if more than half
the tx_outstanding's were UD and all of the destinations are RC
reachable, arming the CQ doesn't solve the issue.
This patch uses the IB_CQ_REPORT_MISSED_EVENTS on the
ib_req_notify_cq(). If the rc is above 0, the UD send cq completion
callback is called directly to re-arm the send completion timer.
This issue is seen in very large parallel filesystem deployments
and the patch has been shown to correct the issue.
Cc: <stable@vger.kernel.org> Reviewed-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Pull NVMe driver update from Matthew Wilcox:
"These patches have mostly been baking for a few months; sorry I didn't
get them in during the merge window. They're all bug fixes, except
for the addition of the SMART log and the addition to MAINTAINERS."
* git://git.infradead.org/users/willy/linux-nvme:
NVMe: Add namespaces with no LBA range feature
MAINTAINERS: Add entry for the NVMe driver
NVMe: Initialize iod nents to 0
NVMe: Define SMART log
NVMe: Add result to nvme_get_features
NVMe: Set result from user admin command
NVMe: End queued bio requests when freeing queue
NVMe: Free cmdid on nvme_submit_bio error
Linus Torvalds [Fri, 22 Mar 2013 23:41:44 +0000 (16:41 -0700)]
Merge branch 'akpm' (fixes from Andrew)
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mqueue: sys_mq_open: do not call mnt_drop_write() if read-only
mm/hotplug: only free wait_table if it's allocated by vmalloc
dma-debug: update DMA debug API to better handle multiple mappings of a buffer
dma-debug: fix locking bug in check_unmap()
drivers/rtc/rtc-at91rm9200.c: use a variable for storing IMR
drivers/video/ep93xx-fb.c: include <linux/io.h> for devm_ioremap()
drivers/rtc/rtc-da9052.c: fix for rtc device registration
mm: zone_end_pfn is too small
poweroff: change orderly_poweroff() to use schedule_work()
mm/hugetlb: fix total hugetlbfs pages count when using memory overcommit accouting
printk: Provide a wake_up_klogd() off-case
irq_work.h: fix warning when CONFIG_IRQ_WORK=n
Vladimir Davydov [Fri, 22 Mar 2013 22:04:51 +0000 (15:04 -0700)]
mqueue: sys_mq_open: do not call mnt_drop_write() if read-only
mnt_drop_write() must be called only if mnt_want_write() succeeded,
otherwise the mnt_writers counter will diverge.
mnt_writers counters are used to check if remounting FS as read-only is
OK, so after an extra mnt_drop_write() call, it would be impossible to
remount mqueue FS as read-only. Besides, on umount a warning would be
printed like this one:
=====================================
[ BUG: bad unlock balance detected! ]
3.9.0-rc3 #5 Not tainted
-------------------------------------
a.out/12486 is trying to release lock (sb_writers) at:
mnt_drop_write+0x1f/0x30
but there are no more locks to release!
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com> Cc: Doug Ledford <dledford@redhat.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexander Duyck [Fri, 22 Mar 2013 22:04:49 +0000 (15:04 -0700)]
dma-debug: update DMA debug API to better handle multiple mappings of a buffer
There were reports of the igb driver unmapping buffers without calling
dma_mapping_error. On closer inspection issues were found in the DMA
debug API and how it handled multiple mappings of the same buffer.
The issue I found is the fact that the debug_dma_mapping_error would
only set the map_err_type to MAP_ERR_CHECKED in the case that the was
only one match for device and device address. However in the case of
non-IOMMU, multiple addresses existed and as a result it was not setting
this field once a second mapping was instantiated. I have resolved this
by changing the search so that it instead will now set MAP_ERR_CHECKED
on the first buffer that matches the device and DMA address that is
currently in the state MAP_ERR_NOT_CHECKED.
A secondary side effect of this patch is that in the case of multiple
buffers using the same address only the last mapping will have a valid
map_err_type. The previous mappings will all end up with map_err_type
set to MAP_ERR_CHECKED because of the dma_mapping_error call in
debug_dma_map_page. However this behavior may be preferable as it means
you will likely only see one real error per multi-mapped buffer, versus
the current behavior of multiple false errors mer multi-mapped buffer.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Cc: Joerg Roedel <joro@8bytes.org> Reviewed-by: Shuah Khan <shuah.khan@hp.com> Tested-by: Shuah Khan <shuah.khan@hp.com> Cc: Jakub Kicinski <kubakici@wp.pl> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexander Duyck [Fri, 22 Mar 2013 22:04:48 +0000 (15:04 -0700)]
dma-debug: fix locking bug in check_unmap()
In check_unmap() it is possible to get into a dead-locked state if
dma_mapping_error is called. The problem is that the bucket is locked in
check_unmap, and locked again by debug_dma_mapping_error which is called
by dma_mapping_error. To resolve that we must release the lock on the
bucket before making the call to dma_mapping_error.
[akpm@linux-foundation.org: restore 80-col trickery to be consistent with the rest of the file] Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Cc: Joerg Roedel <joro@8bytes.org> Reviewed-by: Shuah Khan <shuah.khan@hp.com> Tested-by: Shuah Khan <shuah.khan@hp.com> Cc: Jakub Kicinski <kubakici@wp.pl> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nicolas Ferre [Fri, 22 Mar 2013 22:04:47 +0000 (15:04 -0700)]
drivers/rtc/rtc-at91rm9200.c: use a variable for storing IMR
On some revisions of AT91 SoCs, the RTC IMR register is not working.
Instead of elaborating a workaround for that specific SoC or IP version,
we simply use a software variable to store the Interrupt Mask Register
and modify it for each enabling/disabling of an interrupt. The overhead
of this is negligible anyway.
The interrupt mask register (IMR) for the RTC is broken on the AT91SAM9x5
sub-family of SoCs (good overview of the members here:
http://www.eewiki.net/display/linuxonarm/AT91SAM9x5 ). The "user visible
effect" is the RTC doesn't work.
That sub-family is less than two years old and only has devicetree (DT)
support and came online circa lk 3.7 . The dust is yet to settle on the
DT stuff at least for AT91 SoCs (translation: lots of stuff is still
broken, so much that it is hard to know where to start).
The fix in the patch is pretty simple: just shadow the silicon IMR
register with a variable in the driver. Some older SoCs (pre-DT) use the
the rtc-at91rm9200 driver (e.g. obviously the AT91RM9200) and they should
not be impacted by the change. There shouldn't be a large volume of
interrupts associated with a RTC.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Reported-by: Douglas Gilbert <dgilbert@interlog.com> Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Ludovic Desroches <ludovic.desroches@atmel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/video/ep93xx-fb.c: include <linux/io.h> for devm_ioremap()
Commit be8678149701 ("drivers/video/ep93xx-fb.c: use devm_ functions")
introduced a build error:
drivers/video/ep93xx-fb.c: In function 'ep93xxfb_probe':
drivers/video/ep93xx-fb.c:532: error: implicit declaration of function 'devm_ioremap'
drivers/video/ep93xx-fb.c:533: warning: assignment makes pointer from integer without a cast
Include <linux/io.h> to pickup the declaration of 'devm_ioremap'.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Acked-by: Ryan Mallon <rmallon@gmail.com> Cc: Damien Cassou <damien.cassou@lifl.fr> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Fri, 22 Mar 2013 22:04:41 +0000 (15:04 -0700)]
poweroff: change orderly_poweroff() to use schedule_work()
David said:
Commit 6c0c0d4d1080 ("poweroff: fix bug in orderly_poweroff()")
apparently fixes one bug in orderly_poweroff(), but introduces
another. The comments on orderly_poweroff() claim it can be called
from any context - and indeed we call it from interrupt context in
arch/powerpc/platforms/pseries/ras.c for example. But since that
commit this is no longer safe, since call_usermodehelper_fns() is not
safe in interrupt context without the UMH_NO_WAIT option.
orderly_poweroff() can be used from any context but UMH_WAIT_EXEC is
sleepable. Move the "force" logic into __orderly_poweroff() and change
orderly_poweroff() to use the global poweroff_work which simply calls
__orderly_poweroff().
While at it, remove the unneeded "int argc" and change argv_split() to
use GFP_KERNEL.
We use the global "bool poweroff_force" to pass the argument, this can
obviously affect the previous request if it is pending/running. So we
only allow the "false => true" transition assuming that the pending
"true" should succeed anyway. If schedule_work() fails after that we
know that work->func() was not called yet, it must see the new value.
This means that orderly_poweroff() becomes async even if we do not run
the command and always succeeds, schedule_work() can only fail if the
work is already pending. We can export __orderly_poweroff() and change
the non-atomic callers which want the old semantics.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reported-by: David Gibson <david@gibson.dropbear.id.au> Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi> Cc: Feng Hong <hongfeng@marvell.com> Cc: Kees Cook <keescook@chromium.org> Cc: Serge Hallyn <serge.hallyn@canonical.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wanpeng Li [Fri, 22 Mar 2013 22:04:40 +0000 (15:04 -0700)]
mm/hugetlb: fix total hugetlbfs pages count when using memory overcommit accouting
hugetlb_total_pages is used for overcommit calculations but the current
implementation considers only the default hugetlb page size (which is
either the first defined hugepage size or the one specified by
default_hugepagesz kernel boot parameter).
If the system is configured for more than one hugepage size, which is
possible since commit a137e1cc6d6e ("hugetlbfs: per mount huge page
sizes") then the overcommit estimation done by __vm_enough_memory()
(resp. shown by meminfo_proc_show) is not precise - there is an
impression of more available/allowed memory. This can lead to an
unexpected ENOMEM/EFAULT resp. SIGSEGV when memory is accounted.
Testcase:
boot: hugepagesz=1G hugepages=1
the default overcommit ratio is 50
before patch:
projects / karo-tx-linux.git / log