Eric Nelson [Mon, 12 Mar 2012 15:04:12 +0000 (15:04 +0000)]
i.MX6: mx6q_sabrelite: add CONFIG_REVISION_TAG
This is needed to support Freescale-supplied userspaces.
At the moment, both the IPU and VPU libraries provided by Freescale
in the "imx-lib" package contain routines which scrape the system
revision from /proc/cpuinfo. In the VPU library, this information is
used to load the proper firmware, allowing a single binary to be used
across various i.MX processors.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
Dirk Behme [Wed, 22 Feb 2012 22:50:19 +0000 (22:50 +0000)]
imximage: Remove overwriting of flash_offset
The flash header supports different flash offsets for different
boot devices. E.g. parallel NOR or OneNAND use a different offset
than FLASH_OFFSET_STANDARD (== 0x400).
The flash offset is correctly read from the configuration in
parse_cfg_cmd(). But is then overwritten wrongly in set_imx_hdr_v1/2().
Fix this by removing this overwriting. Use the flash offset
correctly read from the configuration, instead.
If there is no flash_offset read from the configuration file, i.e.
the BOOT_FROM tag is missing, exit with an error message.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Jason Liu <liu.h.jason@gmail.com> CC: Stefano Babic <sbabic@denx.de> Tested-by: Stefano Babic <sbabic@denx.de>
Marek Vasut [Tue, 6 Mar 2012 10:57:43 +0000 (11:57 +0100)]
IXP: Fix GPIO_INT_ACT_LOW_SET()
The GPIO_INT_ACT_LOW_SET was incorrectly handling interrupt lines higher than 7.
This is due to the fact that there are two registers for total of 16 lines.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Bryan Hundven <bryanhundven@gmail.com> Cc: Michael Schwingen <rincewind@discworld.dascon.de>
Marek Vasut [Tue, 6 Mar 2012 00:10:00 +0000 (01:10 +0100)]
IXP: Fix NAND build warning on PDNB3 and SCPU
nand.c: In function ‘pdnb3_nand_read_buf’:
nand.c:107:4: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
nand.c: In function ‘pdnb3_nand_dev_ready’:
nand.c:124:18: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
Remove the 4-byte-at-time read mode altogether, the most is bogus and will
likely cause unaligned accesses.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Bryan Hundven <bryanhundven@gmail.com> Cc: Michael Schwingen <rincewind@discworld.dascon.de>
Marek Vasut [Tue, 6 Mar 2012 00:00:52 +0000 (01:00 +0100)]
IXP: Squash warnings in IXP NPE
IxEthAcc.c: In function ‘ixEthAccInit’:
IxEthAcc.c:105:21: warning: comparison between ‘IxEthDBStatus’ and ‘enum <anonymous>’ [-Wenum-compare]
IxEthDBAPISupport.c: In function ‘ixEthDBPortAddressSet’:
IxEthDBAPISupport.c:633:18: warning: variable ‘ackPortAddressLock’ set but not used [-Wunused-but-set-variable]
IxQMgrDispatcher.c: In function ‘ixQMgrLLPShow’:
IxQMgrDispatcher.c:1194:18: warning: variable ‘q’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Bryan Hundven <bryanhundven@gmail.com> Cc: Michael Schwingen <rincewind@discworld.dascon.de>
Marek Vasut [Mon, 5 Mar 2012 23:00:12 +0000 (00:00 +0100)]
IXP: Make IXP buildable with arm-linux- toolchains
Add -EB flag to LD to switch endianness of the linker. This should make armeb
targets buildable again. Also, make use of U-Boot's internal libgcc instead of
toolchain's one, this works around the use of libraries from GCC, which might be
little endian.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Bryan Hundven <bryanhundven@gmail.com> Cc: Michael Schwingen <rincewind@discworld.dascon.de>
Matt Porter [Tue, 31 Jan 2012 12:03:57 +0000 (12:03 +0000)]
SPL: Add YMODEM over UART load support
Adds support for loading U-Boot from UART using YMODEM protocol.
If YMODEM support is enabled in SPL and the romcode indicates
that SPL loaded via UART then SPL will wait for start of a
YMODEM transfer via the console port.
Signed-off-by: Matt Porter <mporter@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Mon, 20 Feb 2012 13:27:43 +0000 (13:27 +0000)]
SPL: Add README.omap3
This document describes the SPL process for OMAP3 (and related) boards
as well as a partial memory map and how to verify certain aspects
outside of running on the target.
Robert Delien [Sun, 26 Feb 2012 12:15:06 +0000 (12:15 +0000)]
Introducing 8-bit wide register, mx28_register_8
This patch introduces an 8-bit register, mx28_register_8, in order to
prepare for fixing erroneous 32-bit wide access of registers
hw_clkctrl_frac0 and hw_clkctrl_frac1.
Signed-off-by: Robert Delien <robert@delien.nl> Acked-by: Marek Vasut <marex@denx.de> Tested-by: Marek Vasut <marex@denx.de>
Dirk Behme [Sun, 12 Feb 2012 21:29:47 +0000 (21:29 +0000)]
mx6q: mx6qsabrelite: Update the README
The SD loader binary is now downloadable at
https://wiki.linaro.org/Boards/MX6QSabreLite
under a open-source 3-clause BSD license. Update the README
for this.
The discussion shows that it's hard to change the hardware
regarding the default SPI NOR boot of the SabreLite boards.
I.e. this will stay the default boot. Therefore remove the
'early version of' statement.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Stefano Babic <sbabic@denx.de> CC: Jason Liu <liu.h.jason@gmail.com>
Marek Vasut [Mon, 27 Feb 2012 11:56:39 +0000 (12:56 +0100)]
PXA: Fix warning in zipitz2
Configuring for zipitz2 board...
zipitz2.c: In function ‘board_mmc_init’:
zipitz2.c:85:2: warning: implicit declaration of function ‘pxa_mmc_register’ [-Wimplicit-function-declaration]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Simon Glass [Mon, 21 Nov 2011 10:49:38 +0000 (10:49 +0000)]
arm: Remove jornada link script
This link script seems old and incompatible with relocation and its
own sa1000 start.S file. It isn't used because the CPU's link script
was picked up in preference to this.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
It turns that this really doesn't work very nicely. Instead we should
have a pre-console panic function so that we know that further execution
is impossible and we don't need to worry about trampling on UARTs, etc.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Wolfgang Denk <wd@denx.de>
Tao Hou [Thu, 15 Mar 2012 15:33:58 +0000 (23:33 +0800)]
cfi: fix the incomplete erased status check in buffer write
Without the fix, flash_write_cfibuffer will terminate the erased
status check once an all-0xFF word has been found instead of
continuing the erased status check utill the first non-0xFF word.
Signed-off-by: Tao Hou <hotforest@gmail.com> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Łukasz Majewski [Mon, 12 Mar 2012 22:08:06 +0000 (22:08 +0000)]
usb:udc:samsung:fix Remove the req_config flag
The dev->req_config flag was indicating that the forwarded
request needs to perform the usb gadget delayed status.
This is however not needed anymore, so it can be removed.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Marek Vasut <marex@denx.de>
While receiving packets from FIFO sometimes the buffer provided was
nonaligned. Fix this by taking a temporary aligned buffer and then
copying the content to nonaligned buffer.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
Vipin KUMAR [Tue, 6 Mar 2012 23:39:38 +0000 (23:39 +0000)]
USB:gadget:designware Device controller bugfixes
This patch fixes a few bugs in USB device controller driver.
The fixes are as follows
1. Adding error condition checks eg. NULL return
2. Endpoint other than endpoint 0 (control endpoint) are initialized
only if usb state machine reaches STATE_ADDRESSED or above
3. Zero length packet handling corrected
4. Dead code removed
5. Bulk out endpoint returns after servicing 1 interrupt and returns
back to service if more interrupts are pending
Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Marek Vasut <marex@denx.de>
Vipin KUMAR [Tue, 6 Mar 2012 23:39:37 +0000 (23:39 +0000)]
USB:gadget:designware USB device controller (UDC) implementation
The earlier usb device controller driver was specific to spear platforms. This
patch implements the usb device controller driver as a generic controller which
can be reused by other platforms using this peripheral.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Marek Vasut <marex@denx.de>
Mike Frysinger [Mon, 5 Mar 2012 13:47:00 +0000 (13:47 +0000)]
usb: replace wait_ms() with mdelay()
Common code has a mdelay() func, so use that instead of the usb-specific
wait_ms() func. This also fixes the build errors:
ohci-hcd.c: In function 'submit_common_msg':
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1519:9: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1816:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1827:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1844:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1563:11: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1583:9: sorry, unimplemented: called from here
make[1]: *** [ohci-hcd.o] Error 1
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Marek Vasut <marex@denx.de>
Simon Glass [Mon, 13 Feb 2012 13:51:21 +0000 (13:51 +0000)]
bootstage: arm: Add bootstage calls in board and bootm
Add calls to bootstage before and after relocation, and just
before jumping to the OS.
The idea here is you can call bootstage_report() to get a report.
Additionally, if you define CONFIG_BOOTSTAGE_REPORT then a report is
printed automatically by U-Boot just before jumping to the kernel.
Simon Glass [Mon, 13 Feb 2012 13:51:19 +0000 (13:51 +0000)]
bootstage: Implement core microsecond boot time measurement
This defines the basics of a new boot time measurement feature. This allows
logging of very accurate time measurements as the boot proceeds, by using
an available microsecond counter.
To enable the feature, define CONFIG_BOOTSTAGE in your board config file.
Also available is CONFIG_BOOTSTAGE_REPORT which will cause a report to be
printed just before handing off to the OS.
Most IDs are not named at this stage. For that I would first like to
renumber them all.
Simon Glass [Sat, 10 Dec 2011 11:08:03 +0000 (11:08 +0000)]
bootstage: Define an optional microsecond timer
Define timer_get_boot_us() which returns the number of microseconds
since boot. If undefined then we use get_timer() * 1000.
We can fit this in a 32-bit register which keeps everyone happy on
the efficiency side. It will wrap around after about an hour. If we
are still looking at it after an hour then we had better not be
timing the boot.
Simon Glass [Sat, 10 Dec 2011 11:07:54 +0000 (11:07 +0000)]
bootstage: Make use of BOOTSTAGE_ID_RUN_OS in show_boot_progress()
This changes the number 15 as used in boot_stage_progress() to use the
new name provided for it. This is a separate patch because it touches
so many files.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
Simon Glass [Sat, 14 Jan 2012 15:24:44 +0000 (15:24 +0000)]
bootstage: Create an initial header for boot progress integers
At present boot_stage_progress() is called with various magic numbers. The
new bootstage.h header will be used to turn these into symbolic names
throughout the code.
The intent is not that these numbers are passed to Linux. In fact by using
an enum to track them we should eventually be able to remove the explict
numbers and just have the stages count up from 0.
Reinhard Arlt [Fri, 18 Nov 2011 09:06:52 +0000 (09:06 +0000)]
bootvx: Clear and disable data cache, and call vxWorks with parameter.
This patch clear and disable the data cache for vxWorks.
The entry point sysInit(int) intended by Windriver to be called from
the vxWorks bootrom, a very small vxWorks system.
The routine is called by the go() handler in the bootrom, that clears
the cache from start of image to end of usable memory.
The PowerPC implementations only invalidates and disable the cache,
the ARM implementations also flush it.
U-Boot will be on the safe side, if it disables the data cache before
calling vxWorks sysInit(int).
Mike Frysinger [Thu, 10 Nov 2011 14:11:04 +0000 (14:11 +0000)]
net/miiphy/serial: drop duplicate "NAMESIZE" define
A few subsystems are using the same define "NAMESIZE". This has been
working so far because they define it to the same number. However, I
want to change the size of eth_device's NAMESIZE, so rather than tweak
the define names, simply drop references to it. Almost no one does,
and the handful that do can easily be changed to a sizeof().
Reinhard Arlt [Thu, 10 Nov 2011 08:51:57 +0000 (08:51 +0000)]
CPCI750: Add CPCI-HD/2 support
This patch adds support for the esd CPCI-HD/2 board to u-boot for CPCI-CPU/750.
As the primary devices on the CPCI-HD/2 board are connected to device 1 and 3,
the device must be swapped.
Wolfgang Denk [Sat, 17 Mar 2012 20:50:59 +0000 (21:50 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-avr32
* 'master' of git://git.denx.de/u-boot-avr32:
atmel_mci.h: remove outdated register macros
doc/git-mailrc: add <me> to avr32 alias
ATMEL: remove old atmel_mci driver
ATMEL: use generic mmc framework
Andreas Bießmann [Tue, 13 Mar 2012 11:43:51 +0000 (12:43 +0100)]
atmel_mci.h: remove outdated register macros
New gen_atmel_mci driver does not use the outated register access macros. Since
the old atmel_mci driver is deleted these macros are no longer necessary.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Sven Schnelle [Fri, 21 Oct 2011 12:49:25 +0000 (14:49 +0200)]
ATMEL: use generic mmc framework
gen_atmel_mci works on AVR32 as well, so no need to use the legacy
mmc driver. This also has the nice side effect of being able to use
SDHC cards an those boards.
Signed-off-by: Sven Schnelle <svens@stackframe.org> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Simon Glass [Wed, 15 Feb 2012 23:51:16 +0000 (15:51 -0800)]
sandbox: add getopt support
This adds simple command-line parsing to sandbox. The idea is that it
sets up the state with options provided, and this state can then be
queried later, as needed.
New flags are declared with the SB_CMDLINE_OPT_SHORT helper macro,
pointers are automatically gathered up in a special section, and
then the core code takes care of gathering them up and processing
at runtime. This way there is no central place where we have to
store a list of flags with ifdefs.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Simon Glass [Sun, 26 Feb 2012 22:38:50 +0000 (17:38 -0500)]
sandbox: allow processing before main loop
In order to pass command line arguments to sandbox we need to be able
to act on them. So take control back at the end of board_init_r() from
where we can call the main loop or do something else.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Simon Glass [Wed, 15 Feb 2012 23:51:15 +0000 (15:51 -0800)]
sandbox: add concept of sandbox state
The state exists through the life of U-Boot. It can be adjusted by command
line options and perhaps later through a config file. It is available to
U-Boot through state_...() calls (within sandbox code).
The primary purpose of this is to contain the "hardware" state. It should
only be used by sandbox internal code.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
projects / karo-tx-uboot.git / log