pid_namespace.c/.h: simplify defines

Move BITS_PER_PAGE from pid_namespace.c to pid_namespace.h, since we can
simplify the define PID_MAP_ENTRIES by using the BITS_PER_PAGE.

Signed-off-by: Raphael S.Carvalho <raphael.scarv@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

kernel-pidc-improve-flow-of-a-loop-inside-alloc_pidmap-fix

simplify code

Cc: Raphael S. Carvalho <raphael.scarv@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

kernel/pid.c: improve flow of a loop inside alloc_pidmap.

find_next_offset() searches for an available "cleaned bit" in the
respective pid bitmap (page), so returns the offset if found, otherwise it
returns a value equals to BITS_PER_PAGE.

For example, suppose find_next_offset didn't find any available bit, so
there's no purpose to call mk_pid (Wasteful Cpu Cycles).

Therefore, I found it could be better to call mk_pid after the checking
(offset < BITS_PER_PAGE) returned sucessfully!  Another point: If (offset
< BITS_PER_PAGE) results in a "failure", then mk_pid would be called again
afterwards.

Signed-off-by: Raphael S. Carvalho <raphael.scarv@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipc/sem.c: alternatives to preempt_disable()

ipc/sem.c uses a custom wakeup scheme that relies on preempt_disable().
On -RT, this causes increased latencies and debug warnings.

The patch adds two additional schemes:
- one built around a completion - could be better for -RT kernels
- one built around a spinlock - unfortunately it's broken
- and the current one

My preferred solution would be the spinlock implementation: RT would use
premptible spinlocks, mainline normal spinlocks.  Thus both get the
optimal implementation without any special code in ipc/sem.c.
Unfortunately, I don't see how it could be fixed.

Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Mike Galbraith <efault@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipc, sem: prevent possible deadlock

In semctl_main(), when cmd == GETALL, we're locking sma->sem_perm.lock
(through sem_lock_and_putref), yet after the conditional, we lock it
again.  Unlock sma right after exiting the conditional.

Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

fix for sem_lock

Fix a typo in sem_lock.  Of course we need to unlock the local
semaphore lock before jumping to lock_all, in the rare case that
somebody started a complex operation while we were spinning on
the spinlock.

Can be folded into patch 7/7 before merging

Signed-off-by: Rik van Riel <riel@redhat.com>
Reported-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipc,sem: fine grained locking for semtimedop

Introduce finer grained locking for semtimedop, to handle the common case
of a program wanting to manipulate one semaphore from an array with
multiple semaphores.

If the call is a semop manipulating just one semaphore in an array with
multiple semaphores, only take the lock for that semaphore itself.

If the call needs to manipulate multiple semaphores, or another caller is
in a transaction that manipulates multiple semaphores, the sem_array lock
is taken, as well as all the locks for the individual semaphores.

On a 24 CPU system, performance numbers with the semop-multi
test with N threads and N semaphores, look like this:

vanilla Davidlohr's Davidlohr's + Davidlohr's +
threads patches rwlock patches v3 patches
10 610652 726325 1783589 2142206
20 341570 365699 1520453 1977878
30 288102 307037 1498167 2037995
40 290714 305955 1612665 2256484
50 288620 312890 1733453 2650292
60 289987 306043 1649360 2388008
70 291298 306347 1723167 2717486
80 290948 305662 1729545 2763582
90 290996 306680 1736021 2757524
100 292243 306700 1773700 3059159

Signed-off-by: Rik van Riel <riel@redhat.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Chegu Vinod <chegu_vinod@hp.com>
Cc: Emmanuel Benisty <benisty.e@gmail.com>
Cc: Jason Low <jason.low2@hp.com>
Reviewed-by: Michel Lespinasse <walken@google.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipc,sem: have only one list in struct sem_queue

Having only one list in struct sem_queue, and only queueing simple
semaphore operations on the list for the semaphore involved, allows us to
introduce finer grained locking for semtimedop.

Signed-off-by: Rik van Riel <riel@redhat.com>
Acked-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Chegu Vinod <chegu_vinod@hp.com>
Cc: Emmanuel Benisty <benisty.e@gmail.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michel Lespinasse <walken@google.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipcsem-open-code-and-rename-sem_lock-fix

propagate the ipc_obtain_object() errno out of sem_obtain_lock()

Cc: Chegu Vinod <chegu_vinod@hp.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Emmanuel Benisty <benisty.e@gmail.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michel Lespinasse <walken@google.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipc,sem: open code and rename sem_lock

Rename sem_lock() to sem_obtain_lock(), so we can introduce a sem_lock()
later that only locks the sem_array and does nothing else.

Open code the locking from ipc_lock() in sem_obtain_lock() so we can
introduce finer grained locking for the sem_array in the next patch.

Signed-off-by: Rik van Riel <riel@redhat.com>
Acked-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Chegu Vinod <chegu_vinod@hp.com>
Cc: Emmanuel Benisty <benisty.e@gmail.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michel Lespinasse <walken@google.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipc,sem: do not hold ipc lock more than necessary

Instead of holding the ipc lock for permissions and security checks, among
others, only acquire it when necessary.

Some numbers....

1) With Rik's semop-multi.c microbenchmark we can see the following
   results:

Baseline (3.9-rc1):
cpus 4, threads: 256, semaphores: 128, test duration: 30 secs
total operations: 151452270, ops/sec 5048409

+  59.40%            a.out  [kernel.kallsyms]  [k] _raw_spin_lock
+   6.14%            a.out  [kernel.kallsyms]  [k] sys_semtimedop
+   3.84%            a.out  [kernel.kallsyms]  [k] avc_has_perm_flags
+   3.64%            a.out  [kernel.kallsyms]  [k] __audit_syscall_exit
+   2.06%            a.out  [kernel.kallsyms]  [k] copy_user_enhanced_fast_string
+   1.86%            a.out  [kernel.kallsyms]  [k] ipc_lock

With this patchset:
cpus 4, threads: 256, semaphores: 128, test duration: 30 secs
total operations: 273156400, ops/sec 9105213

+  18.54%            a.out  [kernel.kallsyms]  [k] _raw_spin_lock
+  11.72%            a.out  [kernel.kallsyms]  [k] sys_semtimedop
+   7.70%            a.out  [kernel.kallsyms]  [k] ipc_has_perm.isra.21
+   6.58%            a.out  [kernel.kallsyms]  [k] avc_has_perm_flags
+   6.54%            a.out  [kernel.kallsyms]  [k] __audit_syscall_exit
+   4.71%            a.out  [kernel.kallsyms]  [k] ipc_obtain_object_check

2) While on an Oracle swingbench DSS (data mining) workload the
   improvements are not as exciting as with Rik's benchmark, we can see
   some positive numbers.  For an 8 socket machine the following are the
   percentages of %sys time incurred in the ipc lock:

Baseline (3.9-rc1):
100 swingbench users: 8,74%
400 swingbench users: 21,86%
800 swingbench users: 84,35%

With this patchset:
100 swingbench users: 8,11%
400 swingbench users: 19,93%
800 swingbench users: 77,69%

[riel@redhat.com: fix two locking bugs]
Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Chegu Vinod <chegu_vinod@hp.com>
Acked-by: Michel Lespinasse <walken@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Emmanuel Benisty <benisty.e@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipc: introduce lockless pre_down ipcctl

Various forms of ipc use ipcctl_pre_down() to retrieve an ipc object and
check permissions, mostly for IPC_RMID and IPC_SET commands.

Introduce ipcctl_pre_down_nolock(), a lockless version of this function.
The locking version is retained, yet modified to call the nolock version
without affecting its semantics, thus transparent to all ipc callers.

Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Chegu Vinod <chegu_vinod@hp.com>
Cc: Emmanuel Benisty <benisty.e@gmail.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipc-introduce-obtaining-a-lockless-ipc-object-fix

propagate the ipc_obtain_object() errno from ipc_lock()

Cc: Chegu Vinod <chegu_vinod@hp.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Emmanuel Benisty <benisty.e@gmail.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michel Lespinasse <walken@google.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipc: introduce obtaining a lockless ipc object

Through ipc_lock() and therefore ipc_lock_check() we currently return the
locked ipc object.  This is not necessary for all situations and can,
therefore, cause unnecessary ipc lock contention.

Introduce analogous ipc_obtain_object() and ipc_obtain_object_check()
functions that only lookup and return the ipc object.

Both these functions must be called within the RCU read critical section.

Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Chegu Vinod <chegu_vinod@hp.com>
Acked-by: Michel Lespinasse <walken@google.com>
Cc: Emmanuel Benisty <benisty.e@gmail.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipc: remove bogus lock comment for ipc_checkid

This series makes the sysv semaphore code more scalable, by reducing the
time the semaphore lock is held, and making the locking more scalable for
semaphore arrays with multiple semaphores.

The first four patches were written by Davidlohr Buesso, and reduce the
hold time of the semaphore lock.

The last three patches change the sysv semaphore code locking to be more
fine grained, providing a performance boost when multiple semaphores in a
semaphore array are being manipulated simultaneously.

On a 24 CPU system, performance numbers with the semop-multi
test with N threads and N semaphores, look like this:

vanilla Davidlohr's Davidlohr's + Davidlohr's +
threads patches rwlock patches v3 patches
10 610652 726325 1783589 2142206
20 341570 365699 1520453 1977878
30 288102 307037 1498167 2037995
40 290714 305955 1612665 2256484
50 288620 312890 1733453 2650292
60 289987 306043 1649360 2388008
70 291298 306347 1723167 2717486
80 290948 305662 1729545 2763582
90 290996 306680 1736021 2757524
100 292243 306700 1773700 3059159

This patch:

There is no reason to be holding the ipc lock while reading ipcp->seq,
hence remove misleading comment.

Also simplify the return value for the function.

Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Chegu Vinod <chegu_vinod@hp.com>
Cc: Emmanuel Benisty <benisty.e@gmail.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michel Lespinasse <walken@google.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipc/msgutil.c: use linux/uaccess.h

Signed-off-by: HoSung Jung <rain6557@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipc: find_msg can be static

Fixes sparse warning identified by Fengguang's test robot:
   ipc/msg.c:810:16: sparse: symbol 'find_msg' was not declared. Should it be static?

Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipc: refactor msg list search into separate function

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipc: simplify msg list search

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipc: implement MSG_COPY as a new receive mode

Teach the helper routines about MSG_COPY so that msgtyp is preserved as
the message number to copy.

The security functions affected by this change were audited and no
additional changes are necessary.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipc: remove msg handling from queue scan

In preparation for refactoring the queue scan into a separate
function, relocate msg copying.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipc: set EFAULT as default error in load_msg()

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipc: tighten msg copy loops

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipc: separate msg allocation from userspace copy

Separating msg allocation enables single-block vmalloc
allocation instead.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ipc: clamp with min()

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

kexec-use-min_t-to-simplify-logic-fix

replace min_t with min, remove unneeded casts

Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Joe Perches <joe@perches.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

kexec: Use min() and min_t() to simplify logic

Simplify the logic of variable assignments.

Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

kexec: fix wrong types of some local variables

The types of the following local variables:

- ubytes/mbytes in kimage_load_crash_segment()/kimage_load_normal_segment()

- r in vmcoreinfo_append_str()

are wrong, so fix them.

Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

exec: do not abuse ->cred_guard_mutex in threadgroup_lock()

threadgroup_lock() takes signal->cred_guard_mutex to ensure that
thread_group_leader() is stable.  This doesn't look nice, the scope of
this lock in do_execve() is huge.

And as Dave pointed out this can lead to deadlock, we have the
following dependencies:

do_execve: cred_guard_mutex -> i_mutex
cgroup_mount: i_mutex -> cgroup_mutex
attach_task_by_pid: cgroup_mutex -> cred_guard_mutex

Change de_thread() to take threadgroup_change_begin() around the
switch-the-leader code and change threadgroup_lock() to avoid
->cred_guard_mutex.

Note that de_thread() can't sleep with ->group_rwsem held, this can
obviously deadlock with the exiting leader if the writer is active, so it
does threadgroup_change_end() before schedule().

Reported-by: Dave Jones <davej@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

set_task_comm: kill the pointless memset() + wmb()

set_task_comm() does memset() + wmb() before strlcpy().  This buys nothing
and to add to the confusion, the comment is wrong.

- We do not need memset() to be "safe from non-terminating string
  reads", the final char is always zero and we never change it.

- wmb() is paired with nothing, it cannot prevent from printing
  the mixture of the old/new data unless the reader takes the lock.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

procfs-improve-scaling-in-proc-v5

v5: Corrected some warnings from sparce including the supplied by Sasha.

Signed-off-by: Nathan Zimmer <nzimmer@sgi.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

procfs: improve scaling in proc

I am currently tracking a hotlock reported by a customer on a large
system, 512 cores.  I am currently running 3.8-rc7 but the issue looks
like it has been this way for a very long time.  The offending lock is
proc_dir_entry->pde_unload_lock.

This patch converts the lock to use rcu.  However the pde_openers list
still is controlled by a spin lock.  I tested on a 4096 machine and the
lock doesn't seem hot at least according to perf.

This is a refresh of what was orignally suggested by Eric Dumazet some
time ago.  I have also taken in some comments from Andrew and several
other people whose names escape me but I am quite grateful too.

Supporting numbers, lower is better, they are from the test I posted earlier.
cpuinfo baseline        Rcu
tasks   read-sec        read-sec
1       0.0141          0.0141
2       0.0140          0.0142
4       0.0140          0.0141
8       0.0145          0.0140
16      0.0553          0.0168
32      0.1688          0.0549
64      0.5017          0.1690
128     1.7005          0.5038
256     5.2513          2.0804
512     8.0529          3.0162

Signed-off-by: Nathan Zimmer <nzimmer@sgi.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

coredump: change wait_for_dump_helpers() to use wait_event_interruptible()

wait_for_dump_helpers() calls wake_up/kill_fasync from inside the
wait_event-like loop.  This is not needed and in fact this is not strictly
correct, we can/should do this only once after we change pipe->writers.
We could even check if it becomes zero.

Change this code to use use wait_event_interruptible(), this can also help
to make this wait freezable.

With this patch we check pipe->readers without pipe_lock(), this is fine.
Once we see pipe->readers == 1 we know that the handler decremented the
counter, this is all we need.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Mandeep Singh Baines <msb@chromium.org>
Cc: Neil Horman <nhorman@redhat.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

coredump: factor out the setting of PF_DUMPCORE

Cleanup.  Every linux_binfmt->core_dump() sets PF_DUMPCORE, move this into
zap_threads() called by do_coredump().

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Mandeep Singh Baines <msb@chromium.org>
Cc: Neil Horman <nhorman@redhat.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

coredump: introduce dump_interrupted()

By discussion with Mandeep.

Change dump_write(), dump_seek() and do_coredump() to check
signal_pending() and abort if it is true.  dump_seek() does this only
before f_op->llseek(), otherwise it relies on dump_write().

We need this change to ensure that the coredump won't delay suspend, and
to ensure it reacts to SIGKILL "quickly enough", a core dump can take a
lot of time.  In particular this can help oom-killer.

We add the new trivial helper, dump_interrupted() to add the comments and
to simplify the potential freezer changes.  Perhaps it will have more
callers.

Ideally it should do try_to_freeze() but then we need the unpleasant
changes in dump_write() and wait_for_dump_helpers().  It is not trivial to
change dump_write() to restart if f_op->write() fails because of
freezing().  We need to handle the short writes, we need to clear
TIF_SIGPENDING (and we can't rely on recalc_sigpending() unless we change
it to check PF_DUMPCORE).  And if the buggy f_op->write() sets
TIF_SIGPENDING we can not distinguish this case from the race with
freeze_task() + __thaw_task().

So we simply accept the fact that the freezer can truncate a core-dump but
at least you can reliably suspend.  Hopefully we can tolerate this
unlikely case and the necessary complications doesn't worth a trouble.
But if we decide to make the coredumping freezable later we can do this on
top of this change.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Mandeep Singh Baines <msb@chromium.org>
Cc: Neil Horman <nhorman@redhat.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

coredump: sanitize the setting of signal->group_exit_code

Now that the coredumping process can be SIGKILL'ed, the setting of
->group_exit_code in do_coredump() can race with complete_signal() and
SIGKILL or 0x80 can be "lost", or wait(status) can report status ==
SIGKILL | 0x80.

But the main problem is that it is not clear to me what should we do if
binfmt->core_dump() succeeds but SIGKILL was sent, that is why this patch
comes as a separate change.

This patch adds 0x80 if ->core_dump() succeeds and the process was not
killed.  But perhaps we can (should?) re-set ->group_exit_code changed by
SIGKILL back to "siginfo->si_signo |= 0x80" in case when core_dumped == T.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Tested-by: Mandeep Singh Baines <msb@chromium.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Neil Horman <nhorman@redhat.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

coredump: ensure that SIGKILL always kills the dumping thread

prepare_signal() blesses SIGKILL sent to the dumping process but this
signal can be "lost" anyway.  The problems is, complete_signal() sees
SIGNAL_GROUP_EXIT and skips the "kill them all" logic.  And even if the
dumping process is single-threaded (so the target is always "correct"),
the group-wide SIGKILL is not recorded in task->pending and thus
__fatal_signal_pending() won't be true.  A multi-threaded case has even
more problems.

And even ignoring all technical details, SIGNAL_GROUP_EXIT doesn't look
right to me.  This coredumping process is not exiting yet, it can do a lot
of work dumping the core.

With this patch the dumping process doesn't have SIGNAL_GROUP_EXIT, we set
signal->group_exit_task instead.  This makes signal_group_exit() true and
thus this should equally close the races with exit/exec/stop but allows to
kill the dumping thread reliably.

Notes:
- It is not clear what should we do with ->group_exit_code
  if the dumper was killed, see the next change.

- we need more (hopefully straightforward) changes to ensure
  that SIGKILL actually interrupts the coredump. Basically we
  need to check __fatal_signal_pending() in dump_write() and
  dump_seek().

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Tested-by: Mandeep Singh Baines <msb@chromium.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Neil Horman <nhorman@redhat.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

coredump: only SIGKILL should interrupt the coredumping task

There are 2 well known and ancient problems with coredump/signals, and a
lot of related bug reports:

- do_coredump() clears TIF_SIGPENDING but of course this can't help
  if, say, SIGCHLD comes after that.

  In this case the coredump can fail unexpectedly. See for example
  wait_for_dump_helper()->signal_pending() check but there are other
  reasons.

- At the same time, dumping a huge core on the slow media can take a
  lot of time/resources and there is no way to kill the coredumping
  task reliably. In particular this is not oom_kill-friendly.

This patch tries to fix the 1st problem, and makes the preparation for the
next changes.

We add the new SIGNAL_GROUP_COREDUMP flag set by zap_threads() to indicate
that this process dumps the core.  prepare_signal() checks this flag and
nacks any signal except SIGKILL.

Note that this check tries to be conservative, in the long term we should
probably treat the SIGNAL_GROUP_EXIT case equally but this needs more
discussion.  See marc.info/?l=linux-kernel&m=120508897917439

Notes:
- recalc_sigpending() doesn't check SIGNAL_GROUP_COREDUMP.
  The patch assumes that dump_write/etc paths should never
  call it, but we can change it as well.

- There is another source of TIF_SIGPENDING, freezer. This
  will be addressed separately.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Tested-by: Mandeep Singh Baines <msb@chromium.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Neil Horman <nhorman@redhat.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

kmod: remove call_usermodehelper_fns()

This function suffers from not being able to determine if the cleanup is
called in case it returns -ENOMEM.  Nobody is using it anymore, so let's
remove it.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

usermodehelper: split remaining calls to call_usermodehelper_fns()

These are the only users of call_usermodehelper_fns().  This function
suffers from not being able to determine if the cleanup is called.  Even
if in this places the cleanup pointer is NULL, convert them to use the
separate call_usermodehelper_setup() + call_usermodehelper_exec()
functions so we can remove the _fns variant.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

coredump: remove trailling whitespace

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

KEYS: split call to call_usermodehelper_fns()

Use call_usermodehelper_setup() + call_usermodehelper_exec() instead of
calling call_usermodehelper_fns().  In case there's an OOM in this last
function the cleanup function may not be called - in this case we would
miss a call to key_put().

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Oleg Nesterov <oleg@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <james.l.morris@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

kmod: split call to call_usermodehelper_fns()

Use call_usermodehelper_setup() + call_usermodehelper_exec() instead of
calling call_usermodehelper_fns().  In case the latter returns -ENOMEM the
cleanup function may had not been called - in this case we would not free
argv and module_name.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

usermodehelper-export-_exec-and-_setup-functions-fix

export call_usermodehelper_setup() to modules

Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

usermodehelper: export call_usermodehelper_exec() and call_usermodehelper_setup()

call_usermodehelper_setup() + call_usermodehelper_exec() need to be called
instead of call_usermodehelper_fns() when the cleanup function needs to be
called even when an ENOMEM error occurs.  In this case using
call_usermodehelper_fns() the user can't distinguish if the cleanup
function was called or not.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

selftest: add a test case for PTRACE_PEEKSIGINFO

* Dump signals from process-wide and per-thread queues with
  different sizes of buffers.
* Check error paths for buffers with restricted permissions. A part of
  buffer or a whole buffer is for read-only.
* Try to get nonexistent signal.

Signed-off-by: Andrew Vagin <avagin@openvz.org>
Cc: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Dave Jones <davej@redhat.com>
Cc: "Michael Kerrisk (man-pages)" <mtk.manpages@gmail.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pedro Alves <palves@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

ptrace: add ability to retrieve signals without removing from a queue (v4)

This patch adds a new ptrace request PTRACE_PEEKSIGINFO.

This request is used to retrieve information about pending signals
starting with the specified sequence number.  Siginfo_t structures are
copied from the child into the buffer starting at "data".

The argument "addr" is a pointer to struct ptrace_peeksiginfo_args.
struct ptrace_peeksiginfo_args {
u64 off; /* from which siginfo to start */
u32 flags;
s32 nr; /* how may siginfos to take */
};

"nr" has type "s32", because ptrace() returns "long", which has 32 bits on
i386 and a negative values is used for errors.

Currently here is only one flag PTRACE_PEEKSIGINFO_SHARED for dumping
signals from process-wide queue.  If this flag is not set, signals are
read from a per-thread queue.

The request PTRACE_PEEKSIGINFO returns a number of dumped signals.  If a
signal with the specified sequence number doesn't exist, ptrace returns
zero.  The request returns an error, if no signal has been dumped.

Errors:
EINVAL - one or more specified flags are not supported or nr is negative
EFAULT - buf or addr is outside your accessible address space.

A result siginfo contains a kernel part of si_code which usually striped,
but it's required for queuing the same siginfo back during restore of
pending signals.

This functionality is required for checkpointing pending signals.  Pedro
Alves suggested using it in "gdb" to peek at pending signals.  gdb already
uses PTRACE_GETSIGINFO to get the siginfo for the signal which was already
dequeued.  This functionality allows gdb to look at the pending signals
which were not reported yet.

The prototype of this code was developed by Oleg Nesterov.

Signed-off-by: Andrew Vagin <avagin@openvz.org>
Cc: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Dave Jones <davej@redhat.com>
Cc: "Michael Kerrisk (man-pages)" <mtk.manpages@gmail.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pedro Alves <palves@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

Documentation: update nfs option in filesystem/vfat.txt

Add descriptions about 'stale_rw' and 'nostale_ro' nfs options in
filesystem/vfat.txt

Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Ravishankar N <ravi.n1@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

fat (exportfs): rebuild directory-inode if fat_dget()

This patch enables rebuilding of directory inodes which are not present in
the cache.This is done by traversing the disk clusters to find the
directory entry of the parent directory and using its i_pos to build the
inode.

The traversal is done by fat_scan_logstart() which is similar to
fat_scan() but matches i_pos values instead of names.fat_scan_logstart()
needs an inode parameter to work, for which a dummy inode is created by
it's caller fat_rebuild_parent().  This dummy inode is destroyed after the
traversal completes.

All this is done  only if the nostale_ro nfs mount option is specified.

Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Ravishankar N <ravi.n1@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

fat (exportfs): rebuild inode if ilookup() fails

If the cache lookups fail,use the i_pos value to find the directory entry
of the inode and rebuild the inode.Since this involves accessing the FAT
media, do this only if the nostale_ro nfs mount option is specified.

Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Ravishankar N <ravi.n1@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

fat: restructure export_operations

Define two nfs export_operation structures,one for 'stale_rw' mounts and
the other for 'nostale_ro'.  The latter uses i_pos as a basis for encoding
and decoding file handles.

Also, assign i_pos to kstat->ino.  The logic for rebuilding the inode is
added in the subsequent patches.

Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Ravishankar N <ravi.n1@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

fat: introduce a helper fat_get_blknr_offset()

Introduce helper function to get the block number and offset for a given
i_pos value.  Use it in __fat_write_inode() now and later on in nfs.c

Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Ravishankar N <ravi.n1@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

fat: move fat_i_pos_read to fat.h

Move fat_i_pos_read to fat.h so that it can be called from nfs.c in the
subsequent patches to encode the file handle.

Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Ravishankar N <ravi.n1@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

fat: introduce 2 new values for the -o nfs mount option

This patchset eliminates the client side ESTALE errors when a FAT
partition exported over NFS has its dentries evicted from the cache.  The
idea is to find the on-disk location_'i_pos' of the dirent of the inode
that has been evicted and use it to rebuild the inode.

This patch:

Provide two possible values 'stale_rw' and 'nostale_ro' for the -o nfs
mount option.The first one allows all file operations but does not reduce
ESTALE errors on memory constrained systems.  The second one eliminates
ESTALE errors but mounts the filesystem as read-only.  Not specifying a
value defaults to 'stale_rw'.

Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Ravishankar N <ravi.n1@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

hfsplus-fix-warnings-in-fs-hfsplus-bfindc-in-function-hfs_find_1st_rec_by_cnid-fix

make the workaround more explicit

Cc: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

hfsplus: fix warnings in fs/hfsplus/bfind.c

fs/hfsplus/bfind.c: In function 'hfs_find_1st_rec_by_cnid':
(1) include/uapi/linux/swab.h:60:2: warning: 'search_cnid' may be used uninitialized in this function [-Wmaybe-uninitialized]
(2) include/uapi/linux/swab.h:60:2: warning: 'cur_cnid' may be used uninitialized in this function [-Wmaybe-uninitialized]

Signed-off-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

drivers/rtc/rtc-max8907.c: remove redundant code

Remove unnecessary goto statements to simplify the code.
devm_request_threaded_irq returns 0 upon success, hence explicit return 0
is not necessary.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Chiwoong Byun <woong.byun@samsung.com>
Cc: Jonghwa Lee <jonghwa3.lee@samsung.com>
Cc: Laxman dewangan <ldewangan@nvidia.com>
Cc: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

drivers/rtc/rtc-max77686.c: fix incorrect return value on error

'ret' was not initialized to error code before returning. While
at it also remove some redundant code and cleanup.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Chiwoong Byun <woong.byun@samsung.com>
Cc: Jonghwa Lee <jonghwa3.lee@samsung.com>
Cc: Laxman dewangan <ldewangan@nvidia.com>
Cc: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

drivers/rtc/rtc-max8997.c: fix incorrect return value on error

'ret' was being returned without initializing it to error code.  While at
it also remove duplicate return statement.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Jonghwa Lee <jonghwa3.lee@samsung.com>
Cc: Chiwoong Byun <woong.byun@samsung.com>
Cc: Laxman dewangan <ldewangan@nvidia.com>
Cc: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

drivers/rtc/rtc-tps65910.c: fix incorrect return value on error

'ret' was not initialized to correct error value before returning.  Since
'irq' is also being tested for 0, we cannot return irq itself as it means
function is success even though we are returning before completing the
probe.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Chiwoong Byun <woong.byun@samsung.com>
Cc: Jonghwa Lee <jonghwa3.lee@samsung.com>
Cc: Laxman dewangan <ldewangan@nvidia.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

drivers/rtc/rtc-tps6586x.c: remove incorrect use of rtc_device_unregister

Device managed functions do not need explicit freeing/unregistering.
Moreover in this case it was done using non-device managed function which
is incorrect.  Hence remove it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Laxman dewangan <ldewangan@nvidia.com>
Cc: Chiwoong Byun <woong.byun@samsung.com>
Cc: Jonghwa Lee <jonghwa3.lee@samsung.com>
Cc: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

drivers/rtc/rtc-88pm80x.c: add CONFIG_PM_SLEEP to suspend/resume functions

Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following build
warning when CONFIG_PM_SLEEP is not selected.  This is because sleep PM
callbacks defined by SIMPLE_DEV_PM_OPS are only used when the
CONFIG_PM_SLEEP is enabled.

drivers/rtc/rtc-88pm80x.c:238:12: warning: 'pm80x_rtc_suspend' defined but not used [-Wunused-function]
drivers/rtc/rtc-88pm80x.c:243:12: warning: 'pm80x_rtc_resume' defined but not used [-Wunused-function]

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

drivers/rtc/rtc-ds1374.c: add CONFIG_PM_SLEEP to suspend/resume functions

Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following build
warning when CONFIG_PM_SLEEP is not selected.  This is because sleep PM
callbacks defined by SIMPLE_DEV_PM_OPS are only used when the
CONFIG_PM_SLEEP is enabled.

drivers/rtc/rtc-ds1374.c:413:12: warning: 'ds1374_suspend' defined but not used [-Wunused-function]
drivers/rtc/rtc-ds1374.c:422:12: warning: 'ds1374_resume' defined but not used [-Wunused-function]

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

drivers/rtc/rtc-palmas.c: add dt support

Add of_device_id table for Palma RTC to be enable the driver from DT file.

The driver can be registered from DT file as:
palmas: tps65913@58 {
:::::::::::
palmas_rtc {
compatible = "ti,palmas-rtc";
interrupt-parent = <&palmas>;
interrupts = <8 0>;
};
};

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

drivers/rtc/rtc-omap.c: update to devm_* API

Update the code to use devm_* API so that driver core will manage
resources.

Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-tps80031: switch to using SIMPLE_DEV_PM_OPS

Switch to using the SIMPLE_DEV_PM_OPS macro to declare the driver's
pm_ops.  It reduces code size.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-tps65910: switch to using SIMPLE_DEV_PM_OPS

Switch to using the SIMPLE_DEV_PM_OPS macro to declare the driver's
pm_ops.  It reduces code size.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-tps6586x: switch to using SIMPLE_DEV_PM_OPS

Switch to using the SIMPLE_DEV_PM_OPS macro to declare the driver's
pm_ops.  It reduces code size.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-wm8350: switch to using SIMPLE_DEV_PM_OPS

Switch to using the SIMPLE_DEV_PM_OPS macro to declare the driver's
pm_ops.  It reduces code size.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-sh: switch to using SIMPLE_DEV_PM_OPS

Switch to using the SIMPLE_DEV_PM_OPS macro to declare the driver's
pm_ops.  It reduces code size.  Also, CONFIG_PM_SLEEP is added to prevent
build warning when CONFIG_PM_SLEEP is not selected.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-sa1100: switch to using SIMPLE_DEV_PM_OPS

Switch to using the SIMPLE_DEV_PM_OPS macro to declare the driver's
pm_ops.  It reduces code size.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-rc5t583: switch to using SIMPLE_DEV_PM_OPS

Switch to using the SIMPLE_DEV_PM_OPS macro to declare the driver's
pm_ops.  It reduces code size.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-pxa: switch to using SIMPLE_DEV_PM_OPS

Switch to using the SIMPLE_DEV_PM_OPS macro to declare the driver's
pm_ops.  It reduces code size.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-mxc: switch to using SIMPLE_DEV_PM_OPS

Switch to using the SIMPLE_DEV_PM_OPS macro to declare the driver's
pm_ops.  It reduces code size.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-at91rm9200: switch to using SIMPLE_DEV_PM_OPS

Switch to using the SIMPLE_DEV_PM_OPS macro to declare the driver's
pm_ops.  It reduces code size.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-x1205: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-wm8350: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-tile: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-test: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-sun4v: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-starfire: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-rx8581: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-rx4581: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-rv3029c2: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-rs5c313: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-rc5t583: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-r9701: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-ps3: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-max6902: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-max6900: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-m48t86: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-m41t94: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-m41t93: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-ls1x: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: hid-sensor-time: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-generic: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-em3027: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-efi: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-ds3234: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

rtc: rtc-ds1672: use devm_rtc_device_register()

devm_rtc_device_register() is device managed and makes cleanup paths
simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>