Olof Johansson [Fri, 3 Apr 2015 18:26:08 +0000 (11:26 -0700)]
Merge tag 'renesas-soc-cleanup3-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
Merge "Third Round of Renesas ARM Based SoC Cleanup for v4.1" from Simon
Horman:
* Remove default cpuidle driver, it does not appear to serve any purpose
* tag 'renesas-soc-cleanup3-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: cpuidle: Remove the pointless default driver
Olof Johansson [Fri, 3 Apr 2015 18:01:54 +0000 (11:01 -0700)]
Merge branch 'next/dt' into for-next
* next/dt:
ARM: mvebu: armada-385-ap: Enable USB3 port
ARM: mvebu: Enable Performance Monitor Unit on Armada 380/385 SoC
ARM: mvebu: Enable Performance Monitor Unit on Armada 375 SoC
ARM: mvebu: Enable Performance Monitor Unit on Armada XP/370 SoCs
ARM: Kirkwood: add DT description for nas2big
Olof Johansson [Fri, 3 Apr 2015 18:01:40 +0000 (11:01 -0700)]
Merge branch 'next/drivers' into for-next
* next/drivers:
ARM OMAP2+ GPMC: fix programming/showing reserved timing parameters
ARM OMAP2+ GPMC: fix WAITMONITORINGTIME divider bug
ARM OMAP2+ GPMC: calculate GPMCFCLKDIVIDER based on WAITMONITORINGTIME
ARM OMAP2+ GPMC: always program GPMCFCLKDIVIDER
ARM OMAP2+ GPMC: change get_gpmc_timing_reg output for DTS
ARM OMAP2+ GPMC: fix debug output alignment
ARM OMAP2+ GPMC: add bus children
ARM OMAP2+ GPMC: don't undef DEBUG
ARM: OMAP2+: gpmc: make gpmc_cs_get_name() static
ARM: OMAP2+: gpmc: Fix writing in gpmc_cs_set_memconf
Olof Johansson [Fri, 3 Apr 2015 18:00:47 +0000 (11:00 -0700)]
Merge tag 'gpmc-omap-for-v4.1' of git://github.com/rogerq/linux into next/drivers
Merge "OMAP-GPMC driver fixes for v4.1" from Roger Quandros:
* Fixed WAITMONITORINGTIME programming to be based on
GPMC_CLK instead of GPMC_FCLK. The GPMC clock divider
programming is fixed for both synchronous and asynchronous
modes.
* Allow GPMC's children of default bus type to be populated in
the device tree.
* Improved DEBUG output data and format.
* Prevent writing 1 into reserved bits of GPMC_CONFIG7.
* tag 'gpmc-omap-for-v4.1' of git://github.com/rogerq/linux:
ARM OMAP2+ GPMC: fix programming/showing reserved timing parameters
ARM OMAP2+ GPMC: fix WAITMONITORINGTIME divider bug
ARM OMAP2+ GPMC: calculate GPMCFCLKDIVIDER based on WAITMONITORINGTIME
ARM OMAP2+ GPMC: always program GPMCFCLKDIVIDER
ARM OMAP2+ GPMC: change get_gpmc_timing_reg output for DTS
ARM OMAP2+ GPMC: fix debug output alignment
ARM OMAP2+ GPMC: add bus children
ARM OMAP2+ GPMC: don't undef DEBUG
ARM: OMAP2+: gpmc: make gpmc_cs_get_name() static
ARM: OMAP2+: gpmc: Fix writing in gpmc_cs_set_memconf
Olof Johansson [Fri, 3 Apr 2015 17:55:21 +0000 (10:55 -0700)]
Merge tag 'mvebu-dt-4.1-2' of git://git.infradead.org/linux-mvebu into next/dt
Merge "ARM: mvebu: dt changes for v4.1 (round 2)" from Gregory Clement:
mvebu dt changes for v4.1 (part #2)
- add support for Performance Monitor Unit on most of mvebu SoCs
- add nas2big support
- add support for USB3 port On Armada 385 AP
* tag 'mvebu-dt-4.1-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: armada-385-ap: Enable USB3 port
ARM: mvebu: Enable Performance Monitor Unit on Armada 380/385 SoC
ARM: mvebu: Enable Performance Monitor Unit on Armada 375 SoC
ARM: mvebu: Enable Performance Monitor Unit on Armada XP/370 SoCs
ARM: Kirkwood: add DT description for nas2big
Olof Johansson [Fri, 3 Apr 2015 17:53:51 +0000 (10:53 -0700)]
Merge branch 'next/cleanup' into for-next
* next/cleanup:
ARM: OMAP2+: Remove legacy support for omap3 TouchBook
ARM: OMAP3: Remove legacy support for devkit8000
ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
ARM: shmobile: Consolidate the pm code for R-Car Gen2
ARM: shmobile: r8a7791: Correct SYSCIER value
ARM: shmobile: r8a7790: Correct SYSCIER value
Olof Johansson [Fri, 3 Apr 2015 17:52:29 +0000 (10:52 -0700)]
Merge tag 'renesas-pm-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
Merge "Renesas ARM Based SoC PM Updates for v4.1" from Simon Horman:
* Consolidate the pm code for R-Car Gen2
* Correct SYSCIER value for r8a7790 and r8a7791 SoCs
* tag 'renesas-pm-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Consolidate the pm code for R-Car Gen2
ARM: shmobile: r8a7791: Correct SYSCIER value
ARM: shmobile: r8a7790: Correct SYSCIER value
Olof Johansson [Fri, 3 Apr 2015 17:51:02 +0000 (10:51 -0700)]
Merge tag 'v4.1-legacy' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Merge "omap legacy boot clean-up for v4.1" from Tony Lindgren:
Drop three omap3 legacy board-*.c files
We want to get omap3 moved over to device tree only based booting.
These three board-*.c files seem to be inactive, so let's attempt
to drop them now rather than later. With these dropped, we have
omap3 device tree conversion status in a known state. Then we know
that we have .dts support for the remaining omap3 board-*.c files,
or it's being worked on.
By dropping these files now, we can simply revert them if really
needed for the next few merge cycles if we run into suprises.
Reverting things later on will not be so easily done.
* tag 'v4.1-legacy' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove legacy support for omap3 TouchBook
ARM: OMAP3: Remove legacy support for devkit8000
ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
Olof Johansson [Fri, 3 Apr 2015 17:49:51 +0000 (10:49 -0700)]
Merge tag 'v4.1-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/defconfig
Merge "omap defconfig changes for v4.1" from Tony Lindgren:
Few omap2plus_defconfig updates to add commonly used drivers as
loadable modules.
Note that I'll do patches for armv7_defconfig for these at some
point too once we're happy with omap2plus_defconfig to avoid
extra churn on the defconfig files.
* tag 'v4.1-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap2plus_defconfig: Enable n900 modem as loadable modules
ARM: omap2plus_defconfig: Update bluetooth options
ARM: omap2plus_defconfig: Enable leds-pwm
ARM: omap1_defconfig: drop obsolete Kconfig symbols
arm: config: omap2plus_defconfig: switch over to LZMA compression
ARM: omap2plus_defconfig: Enable EXTCON_GPIO_USB
Nicolas Ferre [Thu, 2 Apr 2015 15:07:57 +0000 (17:07 +0200)]
ARM: at91: add a Kconfig dependency on multi-platform
When building a legacy (non-multi) platforms and if the ARCH_AT91 config option
is enabled there is a build error. We need AT91 to depend on multi-platform
core type options.
Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 3 Apr 2015 17:44:28 +0000 (10:44 -0700)]
Merge tag 'at91-cleanup3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/drivers
Merge "at91: cleanup for 4.1 #3" from Nicolas Ferre:
Third batch of cleanup for 4.1:
- System Timer (ST) for at91rm9200 re-work (syscon/regmap):
- watchdog
- restart handler
- timer as a proper clocksource
=> remove mach dependency + cleanup
* tag 'at91-cleanup3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91: (54 commits)
ARM: at91: remove useless include
clocksource: atmel-st: remove mach/hardware dependency
clocksource: atmel-st: use syscon/regmap
ARM: at91: time: move the system timer driver to drivers/clocksource
ARM: at91: properly initialize timer
ARM: at91: at91rm9200: remove deprecated arm_pm_restart
watchdog: at91rm9200: implement restart handler
watchdog: at91rm9200: use the system timer syscon
mfd: syscon: Add atmel system timer registers definition
ARM: at91/dt: declare atmel,at91rm9200-st as a syscon
ARM: at91: remove old setup
ARM: at91: sama5d4: remove useless map_io
ARM: at91: sama5 use SoC detection infrastructure
ARM: at91: at91sam9: use SoC detection infrastructure
ARM: at91: at91rm9200 use SoC detection infrastructure
ARM: at91: add soc detection infrastructure
ARM: at91/dt: introduce atmel,<chip>-dbgu
ARM: at91: remove unused _matrix.h headers
ARM: at91: remove unused at91_ioremap_matrix and header
ARM: at91: remove NEED_MACH_IO_H
...
Olof Johansson [Thu, 2 Apr 2015 00:59:01 +0000 (17:59 -0700)]
Merge branch 'next/soc' into for-next
* next/soc:
ARM: rockchip: disable watchdog during suspend
ARM: rockchip: decrease the wait time for resume
ARM: rockchip: Constify struct regmap_config and staticize local function
Olof Johansson [Thu, 2 Apr 2015 00:58:49 +0000 (17:58 -0700)]
Merge branch 'next/cleanup' into for-next
* next/cleanup:
ARM: davinci: dm646x: Add interrupt resource for McASPs
ARM: davinci: irqs: Correct McASP1 TX interrupt definition for DM646x
ARM: davinci: dm646x: Clean up the McASP DMA resources
ARM: davinci: devices-da8xx: Add support for McASP2 on da830
ARM: davinci: devices-da8xx: Clean up and correct the McASP device creation
ARM: davinci: devices-da8xx: Add interrupt resource to McASP structs
ARM: davinci: devices-da8xx: Add resource name for the McASP DMA request
Olof Johansson [Thu, 2 Apr 2015 00:58:11 +0000 (17:58 -0700)]
Merge tag 'at91-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/multiplatform
Merge "at91: multiplatform for 4.1 #1" from Nicolas Ferre:
This is the multi-platform support for AT91:
- reworked arch/arm/mach-at91/Kconfig and arch/arm/Kconfig to switch to
multi-platform
- updated at91_dt_defconfig
- continue the cleanup of unneeded files and code chunks
* tag 'at91-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91: (61 commits)
ARM: at91: drop AT91_TIMER_HZ
ARM: at91: remove hardware.h
ARM: at91: remove SoC headers
ARM: at91: remove useless mach/cpu.h
ARM: at91: remove unused headers
ARM: at91: switch at91_dt_defconfig to multiplatform
ARM: at91: switch to multiplatform
ARM: at91: remove useless include
clocksource: atmel-st: remove mach/hardware dependency
clocksource: atmel-st: use syscon/regmap
ARM: at91: time: move the system timer driver to drivers/clocksource
ARM: at91: properly initialize timer
ARM: at91: at91rm9200: remove deprecated arm_pm_restart
watchdog: at91rm9200: implement restart handler
watchdog: at91rm9200: use the system timer syscon
mfd: syscon: Add atmel system timer registers definition
ARM: at91/dt: declare atmel,at91rm9200-st as a syscon
ARM: at91: remove old setup
ARM: at91: sama5d4: remove useless map_io
ARM: at91: sama5 use SoC detection infrastructure
...
Olof Johansson [Thu, 2 Apr 2015 00:56:33 +0000 (17:56 -0700)]
Merge tag 'davinci-for-v4.1/mcasp' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/cleanup
Merge "DaVinci McASP changes for v4.1" from Sekhar Nori:
This pull request contains cleanups and non-urgent fixes for DaVinci
McASP platform support code.
* tag 'davinci-for-v4.1/mcasp' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: dm646x: Add interrupt resource for McASPs
ARM: davinci: irqs: Correct McASP1 TX interrupt definition for DM646x
ARM: davinci: dm646x: Clean up the McASP DMA resources
ARM: davinci: devices-da8xx: Add support for McASP2 on da830
ARM: davinci: devices-da8xx: Clean up and correct the McASP device creation
ARM: davinci: devices-da8xx: Add interrupt resource to McASP structs
ARM: davinci: devices-da8xx: Add resource name for the McASP DMA request
ARM: configs: remove all CONFIG_RCAR_AUDMAC_PP from ARM defconfigs
Renesas R-Car sound (= rsnd) needs 2 DMAC which are called as
Audio DMAC (= 1st DMAC) and Audio DMAC peri peri (2nd DMAC).
And rsnd had assumed that 1st / 2nd DMACs are implemented as DMAEngine.
But, in result of DMA ML discussion, 2nd DMAC was concluded that it is
not a general purpose DMAC (2nd DMAC is for Device to Device inside
sound system). Additionally, current DMAEngine can't support Device to
Device, and we don't have correct DT bindings for it at this point.
So the easiest solution for it is that move it from DMAEngine to rsnd
driver.
Audio DMAC peri peri DMAEngine is no longer needed.
Remove all CONFIG_RCAR_AUDMAC_PP from ARM defconfigs
Olof Johansson [Thu, 2 Apr 2015 00:52:46 +0000 (17:52 -0700)]
Merge tag 'v4.1-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "ARM: rockchip: dts changes for 4.1" from Heiko Stuebner:
This adds and enables the usbphy nodes on the rk3288 boards and enables
the gmac on the firefly board. A new board the Popmetal-rk3288 is also
added. And finally the pmic supplies for act8846 based boards are added,
as the act8865/act8846 driver gained supply handling in the regulator tree.
* tag 'v4.1-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: complete rk3288-evb pmic supplies
ARM: dts: rockchip: add input supplies for the act8846 on Radxa Rock
ARM: dts: add rk3288 PopMetal board
dt-bindings: add root compatible property for PopMetal board
ARM: dts: rockchip: enable gmac on rk3288-firefly
ARM: dts: rockchip: enable usbphy on rk3288-firefly
ARM: dts: rockchip: Enable usb PHY on rk3288-evb board
ARM: dts: rockchip: add rk3288 usb PHY
Olof Johansson [Thu, 2 Apr 2015 00:52:02 +0000 (17:52 -0700)]
Merge tag 'v4.1-rockchip-soc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/soc
Merge "ARM: rockchip: soc code changes for 4.1" from Heiko Stuebner:
Some suspend improvements reducing resume time and making sure the
watchdog does not reset after 12 hours and a change to constify and
staticize some smp parts.
* tag 'v4.1-rockchip-soc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: rockchip: disable watchdog during suspend
ARM: rockchip: decrease the wait time for resume
ARM: rockchip: Constify struct regmap_config and staticize local function
Olof Johansson [Thu, 2 Apr 2015 00:38:49 +0000 (17:38 -0700)]
Merge branch 'next/drivers' into for-next
* next/drivers:
soc: qcom: gsbi: Add support for ADM CRCI muxing
firmware: qcom: scm: Support cpu power down through SCM
firmware: qcom: scm: Add qcom_scm_set_warm_boot_addr function
firmware: qcom: scm: Clean cold boot entry to export only the API
firmware: qcom: scm: Move the scm driver to drivers/firmware
ARM: qcom: Prep scm code for move to drivers/firmware
ARM: qcom: Cleanup scm interface to only export what is needed
ARM: qcom: Merge scm and scm boot code together
Olof Johansson [Thu, 2 Apr 2015 00:35:34 +0000 (17:35 -0700)]
Merge tag 'qcom-soc-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into next/drivers
Merge "qcom SoC changes for v4.1" from Kumar Gala:
Qualcomm ARM Based SoC Updates for v4.1
* Merged the based Qualcomm SCM and SCM boot support
* Cleaned up SCM interface to only expose functional SCM APIs
* Moved Qualcomm SCM code into drivers/firmware
* Updated the SCM APIs for setting cpu cold and warm boot addresses
* Added support for ADM CRCI muxing
* tag 'qcom-soc-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
soc: qcom: gsbi: Add support for ADM CRCI muxing
firmware: qcom: scm: Support cpu power down through SCM
firmware: qcom: scm: Add qcom_scm_set_warm_boot_addr function
firmware: qcom: scm: Clean cold boot entry to export only the API
firmware: qcom: scm: Move the scm driver to drivers/firmware
ARM: qcom: Prep scm code for move to drivers/firmware
ARM: qcom: Cleanup scm interface to only export what is needed
ARM: qcom: Merge scm and scm boot code together
Olof Johansson [Wed, 1 Apr 2015 23:37:30 +0000 (16:37 -0700)]
Merge tag 'renesas-sh73a0-multiplatform-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/multiplatform
Merge "Renesas ARM Based SoC sh73a0 Multiplatform Updates for v4.1" from Simon
Horman:
* Add multiplatform support to sh73a0 and its kzm9g board
* Use Bus State Controller to enable ethernet for multiplatform sh73a0/kzm9g
* Add PM domain support to multiplatform sh73a0
* tag 'renesas-sh73a0-multiplatform-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (43 commits)
ARM: shmobile: sh73a0: Remove restart callback
ARM: shmobile: sh73a0 dtsi: Add PM domain support
ARM: shmobile: sh73a0: Remove unused sh73a0_add_standard_devices_dt()
ARM: shmobile: sh73a0 dtsi: Add Cortex-A9 TWD node
ARM: shmobile: kzm9g-reference: Remove board C code and DT file
ARM: shmobile: kzm9g dts: Move Ethernet node to BSC
ARM: shmobile: sh73a0 dtsi: Add Bus State Controller node
ARM: shmobile: kzm9g: Build DTS for Multiplatform
ARM: shmobile: kzm9g dts: Sync with kzm9g-reference dts
ARM: shmobile: sh73a0: Add Multiplatform support
ARM: shmobile: sh73a0: Introduce generic setup callback
ARM: shmobile: r8a7794: add SDHI DT support
ARM: shmobile: r8a7790: add ADSP clocks
ARM: shmobile: r8a7791: add ADSP clocks
ARM: shmobile: henninger: add CAN0 DT support
ARM: shmobile: r8a7791: add CAN DT support
ARM: shmobile: r8a7791: add CAN clocks
ARM: shmobile: r8a7790: add CAN DT support
ARM: shmobile: r8a7790: add CAN clocks
ARM: shmobile: emev2-kzm9d dts: Add PFC information for uart1
...
Olof Johansson [Sun, 29 Mar 2015 21:00:53 +0000 (14:00 -0700)]
Merge tag 'sunxi-fixes-for-4.0' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Allwinner fixes for 4.0
There's a few fixes to merge for 4.0, one to add a select in the machine
Kconfig option to fix a potential build failure, and two fixing cpufreq related
issues.
* tag 'sunxi-fixes-for-4.0' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sunxi: Remove overclocked/overvoltaged OPP
ARM: dts: sun4i: a10-lime: Override and remove 1008MHz OPP setting
ARM: sunxi: Have ARCH_SUNXI select RESET_CONTROLLER for clock driver usage
Olof Johansson [Sun, 29 Mar 2015 20:58:54 +0000 (13:58 -0700)]
Merge tag 'fixes-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for the -rc cycle:
- Fix a device tree based booting vs legacy booting regression for
omap3 crypto hardware by adding the missing DMA channels.
- Fix /sys/bus/soc/devices/soc0/family for am33xx devices.
- Fix two timer issues that can cause hangs if the timer related
hwmod data is missing like it often initially is for new SoCs.
- Remove pcie hwmods entry from dts as that causes runtime PM to
fail for the PHYs.
- A paper bag type dts configuration fix for dm816x GPIO
interrupts that I just noticed. This is most of the changes
diffstat wise, but as it's a basic feature for connecting
devices and things work otherwise, it should be fixed.
* tag 'fixes-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix gpio interrupts for dm816x
ARM: dts: dra7: remove ti,hwmod property from pcie phy
ARM: OMAP: dmtimer: disable pm runtime on remove
ARM: OMAP: dmtimer: check for pm_runtime_get_sync() failure
ARM: OMAP2+: Fix socbus family info for AM33xx devices
ARM: dts: omap3: Add missing dmas for crypto
Olof Johansson [Sun, 29 Mar 2015 20:47:21 +0000 (13:47 -0700)]
Merge tag 'fixes-for-v4.0-rc5' of https://github.com/rjarzmik/linux into fixes
arm: pxa: fixes for v4.0-rc5
There are only 2 fixes, one for the zeus board about the regulator changes,
where a typo prevented the zeus board from having a working can regulator,
and one regression triggered by the interrupts IRQ shift of 16 affecting all
boards.
* tag 'fixes-for-v4.0-rc5' of https://github.com/rjarzmik/linux:
ARM: pxa: fix pxa interrupts handling in DT
ARM: pxa: Fix typo in zeus.c
Chen-Yu Tsai [Tue, 24 Mar 2015 16:53:27 +0000 (00:53 +0800)]
ARM: dts: sunxi: Remove overclocked/overvoltaged OPP
Without proper regulator support for individual boards, it is dangerous
to have overclocked/overvoltaged OPPs in the list. Cpufreq will increase
the frequency without the accompanying voltage increase, resulting in
an unstable system.
Remove them for now. We can revisit them with the new version of OPP
bindings, which support boost settings and frequency ranges, among
other things.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Mark Jackson [Thu, 19 Mar 2015 15:07:43 +0000 (15:07 +0000)]
ARM: dts: Update Nanobone dts file
Update dts file to reflect:-
* new flash memory layout
* add missing phy-mode property
* dual_emac now just a boolean
* rename mcp to microchip
* update gpio definition
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk> Signed-off-by: Tony Lindgren <tony@atomide.com>
Sakari Ailus [Wed, 18 Mar 2015 23:50:23 +0000 (01:50 +0200)]
ARM: dts: omap3: Add DT entries for OMAP 3 ISP
The resources the ISP needs are slightly different on 3[45]xx and 3[67]xx.
Especially the phy-type property is different.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[tony@atomide.com: use omap3_scm_general instead of scm_conf for now] Signed-off-by: Tony Lindgren <tony@atomide.com>
Pali Rohár [Thu, 26 Feb 2015 13:49:59 +0000 (14:49 +0100)]
ARM: dts: omap3-tao3530: Include directly omap34xx.dtsi
This patch just move content of file omap34xx-hs.dtsi into omap3-tao3530.dts.
There is no code change, patch is just preparation for removing -hs file.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com>
Pali Rohár [Thu, 26 Feb 2015 13:49:58 +0000 (14:49 +0100)]
ARM: dts: n900: Enable omap sham and include directly omap34xx.dtsi
This patch moves content of file omap34xx-hs.dtsi into omap3-n900.dts and enable
omap sham support (omap HW support for SHA + MD5). After testing both omap hwmod
and omap-sham.ko drivers it looks like signed Nokia X-Loader enable L3 firewall
for omap sham. There is no kernel crash with both official bootloader and crypto
enable bootloader. So we can safely enable sham code.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com>
Pali Rohár [Thu, 26 Feb 2015 13:49:57 +0000 (14:49 +0100)]
ARM: dts: n9/n950: Enable omap crypto support
Harmattan system on Nokia N9 and N950 devices uses omap crypto support.
Bootloader on those devices is known that it enables HW crypto support.
This patch just include omap36xx.dtsi directly, so aes and sham is enabled.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Thu, 19 Mar 2015 16:14:36 +0000 (09:14 -0700)]
ARM: dts: Add cppi41 support for dm816x MUSB
Looks like we have cppi41 on dm816x just like on am335x.
Cc: Bin Liu <binmlist@gmail.com> Cc: Brian Hutchinson <b.hutchman@gmail.com> Cc: Felipe Balbi <balbi@ti.com> Cc: Matthijs van Duin <matthijsvanduin@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Thu, 19 Mar 2015 16:14:35 +0000 (09:14 -0700)]
ARM: dts: Fix typo for dm816x usb0_pins
Commit a54879a00859 ("ARM: dts: Fix USB dts configuration for dm816x")
attempted to fix the USB features introduced by commit 7800064ba507
("ARM: dts: Add basic dm816x device tree configuration") but obviously
I did not read the dmesg as more USB issues still keep trickling in.
It should be usb1_pins instead not usb0_pins for the second interface
to avoid warnings from pinctrl framework.
Cc: Brian Hutchinson <b.hutchman@gmail.com> Cc: Felipe Balbi <balbi@ti.com> Cc: Matthijs van Duin <matthijsvanduin@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mark James [Tue, 17 Mar 2015 21:35:23 +0000 (21:35 +0000)]
ARM: socfpga: dts: fix spi1 interrupt
The socfpga.dtsi currently has the wrong interrupt number set for SPI master 1
Trying to use the master without this change results in the kernel boot
process waiting forever for an interrupt that will never occur while
attempting to probe any slave devices configured in the device tree as being
under SPI master 1.
The change works for the Cyclone V, and according to the Arria 5 handbook
should be good there too.
Signed-off-by: Mark James <maj@jamers.net> Acked-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Drop AT91_TIMER_HZ as this can be handled using HZ_FIXED. Initial help message
was:
On AT91rm9200 chips where you're using a system clock derived
from the 32768 Hz hardware clock, this tick rate should divide
it exactly: use a power-of-two value, such as 128 or 256, to
reduce timing errors caused by rounding.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Daniel Lezcano [Tue, 17 Mar 2015 15:25:12 +0000 (16:25 +0100)]
ARM: shmobile: cpuidle: Remove the pointless default driver
The default idle driver uses one state with the WFI instruction.
The default idle routine invokes WFI when no cpuidle driver is present.
The default cpuidle driver is pointless and does not give more than the
default idle routine and moreover it pulls all the mathematics tied with
the cpuidle governor for nothing, hence consuming more energy.
Remove the default driver, the related code and register the driver directly.
[compiled only - no board - no test]
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tony Lindgren [Wed, 18 Mar 2015 20:41:34 +0000 (13:41 -0700)]
ARM: dts: Fix gpio interrupts for dm816x
Commit 7800064ba507 ("ARM: dts: Add basic dm816x device tree
configuration") added basic devices for dm816x, but I was not able
to test the GPIO interrupts earlier until I found some suitable pins
to test with. We can mux the MMC card detect and write protect pins
from SD_SDCD and SD_SDWP mode to use a normal GPIO interrupts that
are also suitable for the MMC subsystem.
This turned out several issues that need to be fixed:
- I set the GPIO type wrong to be compatible with omap3 instead
of omap4. The GPIO controller on dm816x has EOI interrupt
register like omap4 and am335x.
- I got the GPIO interrupt numbers wrong as each bank has two
and we only use one. They need to be set up the same way as
on am335x.
- The gpio banks are missing interrupt controller related
properties.
With these changes the GPIO interrupts can be used with the
MMC card detect pin, so let's wire that up. Let's also mux all
the MMC lines for completeness while at it.
For the first GPIO bank I tested using GPMC lines temporarily
muxed to GPIOs on the dip switch 10.
Cc: Brian Hutchinson <b.hutchman@gmail.com> Cc: Matthijs van Duin <matthijsvanduin@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Thu, 12 Mar 2015 08:06:30 +0000 (10:06 +0200)]
ARM: davinci: irqs: Correct McASP1 TX interrupt definition for DM646x
McASP1 TX interrupt is 30, not 32 on DM646x DMSoC.
While at it remove the bogus AEMIF interrupt entry from
dm646x_default_priorities[]. AEMIF interrupt on DM6467 is
60 not 30 and the entry for the correct interrupt number
is already present in the same table.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[nsekhar@ti.com: remove bogus entry from dm646x_default_priorities[]] Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Roger Quadros [Tue, 17 Mar 2015 09:43:51 +0000 (11:43 +0200)]
ARM: dts: dra7x-evm: beagle-x15: Fix USB Peripheral
Now that we have EXTCON_USB_GPIO queued for v4.1, revert
commit addfcde7c485 ("ARM: dts: dra7x-evm: beagle-x15: Fix USB Host")
On these EVMs, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).
Gets USB peripheral mode to work on this EVM.
Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com>
Suman Anna [Tue, 17 Mar 2015 01:14:02 +0000 (20:14 -0500)]
ARM: OMAP: dmtimer: check for pm_runtime_get_sync() failure
The current OMAP dmtimer probe does not check for the return
status of pm_runtime_get_sync() before initializing the timer
registers. Any timer with missing hwmod data would return a
failure here, and the access of registers without enabling the
clocks for the timer would trigger a l3_noc interrupt and a
kernel boot hang. Add proper checking so that the probe would
return a failure graciously without hanging the kernel boot.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Mon, 16 Mar 2015 17:20:37 +0000 (12:20 -0500)]
ARM: dts: DRA7: Remove ti,timer-dsp and ti,timer-pwm properties
Remove the 'ti,timer-dsp' and 'ti,timer-pwm' properties from the timer
nodes that still have them. This seems to be copied from OMAP5, on
which only certain timers are capable of providing PWM functionality
or be able to interrupt the DSP. All the GPTimers On DRA7 are capable
of PWM and interrupting any core (due to the presence of Crossbar).
These properties were used by the driver to add capabilities to each
timer, and support requesting timers by capability. In the DT world,
we expect any users of timers to use phandles to the respective timer,
and use the omap_dm_timer_request_by_node() API. The API to request
using capabilities, omap_dm_timer_request_by_cap() API should be
deprecated eventually.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Marek Belisko [Fri, 13 Mar 2015 20:40:37 +0000 (21:40 +0100)]
Documentation: omap-twl4030: Move ti,codec property to optional
ti,codec property is not used in omap-twl4030 driver in linux kernel but
we keep it as optional property, so that the existing dtbs do not
become noncompliant after the change on other OS.
Signed-off-by: Marek Belisko <marek@goldelico.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Marek Belisko [Fri, 13 Mar 2015 20:40:36 +0000 (21:40 +0100)]
ARM: dts: omap3: Remove all references to ti,codec property
ti,codec property is not used (parsed) in omap-twl4030 driver. The ti,twl4030-audio
which ti,codec points by phandle is mfd driver and device for ASoC codec is created
w/o DT compatible string. Removing all references in DT files.
Signed-off-by: Marek Belisko <marek@goldelico.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Tue, 17 Mar 2015 00:07:26 +0000 (17:07 -0700)]
ARM: OMAP2+: Remove legacy support for omap3 TouchBook
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
As it seems this board only has minimal support upstreamed for the
legacy booting and has not seen activity for on the mailing lists
for a few years, let's attempt to remove the related legacy board-*.c
file.
I do not have this board, but it seems getting the same level of
support with device tree based booting is mostly just configuring
the .dts file. And there is no need to upgrade the boot loader as
we can boot with appended DTB too. And most of the omap3 boards
seem to be related to omap3-evm, and omap3beagleboard that are
supported with device tree based booting.
If somebody is using this board actively with the mainline kernel,
please communicate this to the linux-omap mailing list so we can
get the board booting with device tree based support. I can help
some too getting the minimal device tree based booting going if
help is needed.
The reason for attempting to remove this board now is that I'd
rather get the remaining omap3 legacy booting support into a known
state where we at least have a .dts file being written for the
remaining legacy boards. That is because for the next few merge
cycles we can still revert this patch if absolutely necessary,
but I'd rather not get suprised by missing .dts files at the point
where we are ready to drop all remaining omap3 legacy booting
support later on.
Tony Lindgren [Mon, 16 Mar 2015 23:56:58 +0000 (16:56 -0700)]
ARM: OMAP3: Remove legacy support for devkit8000
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
As it seems this board only has minimal support upstreamed for the
legacy booting and has not seen activity for on the mailing lists
for a few years, let's attempt to remove the related legacy board-*.c
file.
I do not have this board, but it seems getting the same level of
support with device tree based booting is mostly just configuring
the .dts file. And there is no need to upgrade the boot loader as
we can boot with appended DTB too. And most of the omap3 boards
seem to be related to omap3-evm, and omap3beagleboard that are
supported with device tree based booting.
If somebody is using this board actively with the mainline kernel,
please communicate this to the linux-omap mailing list so we can
get the board booting with device tree based support. I can help
some too getting the minimal device tree based booting going if
help is needed.
The reason for attempting to remove this board now is that I'd
rather get the remaining omap3 legacy booting support into a known
state where we at least have a .dts file being written for the
remaining legacy boards. That is because for the next few merge
cycles we can still revert this patch if absolutely necessary,
but I'd rather not get suprised by missing .dts files at the point
where we are ready to drop all remaining omap3 legacy booting
support later on.
Tony Lindgren [Mon, 16 Mar 2015 23:56:58 +0000 (16:56 -0700)]
ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
As it seems this board only has minimal support upstreamed for the
legacy booting and has not seen activity for on the mailing lists
for a few years, let's attempt to remove the related legacy board-*.c
file.
I do not have this board, but it seems getting the same level of
support with device tree based booting is mostly just configuring
the .dts file. And there is no need to upgrade the boot loader as
we can boot with appended DTB too. And most of the omap3 boards
seem to be related to omap3-evm, and omap3beagleboard that are
supported with device tree based booting.
If somebody is using this board actively with the mainline kernel,
please communicate this to the linux-omap mailing list so we can
get the board booting with device tree based support. I can help
some too getting the minimal device tree based booting going if
help is needed.
The reason for attempting to remove this board now is that I'd
rather get the remaining omap3 legacy booting support into a known
state where we at least have a .dts file being written for the
remaining legacy boards. That is because for the next few merge
cycles we can still revert this patch if absolutely necessary,
but I'd rather not get suprised by missing .dts files at the point
where we are ready to drop all remaining omap3 legacy booting
support later on.
Also looks like this board is no longer listed on ema-tech.com
product page at:
http://ema-tech.com/en/categories.html
Cc: Jason Lam <lzg@ema-tech.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Gaku Inami [Mon, 16 Mar 2015 05:48:43 +0000 (14:48 +0900)]
ARM: shmobile: Consolidate the pm code for R-Car Gen2
The pm code for R-Car Gen2 is scatterd in each SoC. These files
(pm-r8a7790.c/pm-r8a7791.c) have some overlap code. This change
consolidate the pm code for R-Car Gen2 into one.
projects / karo-tx-linux.git / log