scsi_dh: get module reference outside of device handler
We need to grab a reference to the module before calling the attach
routines to avoid a small race vs module removal. It also cleans up
the code significantly as a side effect.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Reviewed-by: Hannes Reinecke <hare@suse.de>
The T10 SBC UNMAP command does not provide any hard guarantees that
blocks will return zeroes on a subsequent READ. This is due to the fact
that the device server is free to silently ignore all or parts of the
request.
The only way to ensure that a block consistently returns zeroes after
being unmapped is to use WRITE SAME with the UNMAP bit set. Should the
device be unable to unmap one or more blocks described by the command it
is required to manually write zeroes to them.
Until now we have preferred UNMAP over the WRITE SAME variants to
accommodate thinly provisioned devices that predated the final SBC-3
spec. This patch changes the heuristic so that we favor WRITE SAME(16)
or (10) over UNMAP if these commands are marked as supported in the
Logical Block Provisioning VPD page.
The patch also disables discard_zeroes_data for devices operating in
UNMAP mode.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
The calling conventions for this function are bad as it could return
-ENODEV both for a device not currently online and a not recognized ioctl.
Add a new scsi_ioctl_block_when_processing_errors function that wraps
scsi_block_when_processing_errors with the a special case for the
SG_SCSI_RESET ioctl command, and handle the SG_SCSI_RESET case itself
in scsi_ioctl. All callers of scsi_ioctl now must call the above helper
to check for the EH state, so that the ioctl handler itself doesn't
have to.
Reported-by: Robert Elliott <Elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
Bart Van Assche [Thu, 30 Oct 2014 13:46:00 +0000 (14:46 +0100)]
scsi: add support for multiple hardware queues in scsi_(host_)find_tag
Modify scsi_find_tag() and scsi_host_find_tag() such that these
functions can translate a tag generated by blk_mq_unique_tag().
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Bart Van Assche [Thu, 30 Oct 2014 13:45:36 +0000 (14:45 +0100)]
scsi: add support for multiple hardware queues
Allow a SCSI LLD to declare how many hardware queues it supports
by setting Scsi_Host.nr_hw_queues before calling scsi_add_host().
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Bart Van Assche [Thu, 30 Oct 2014 13:45:11 +0000 (14:45 +0100)]
blk-mq: add blk_mq_unique_tag()
The queuecommand() callback functions in SCSI low-level drivers
need to know which hardware context has been selected by the
block layer. Since this information is not available in the
request structure, and since passing the hctx pointer directly to
the queuecommand callback function would require modification of
all SCSI LLDs, add a function to the block layer that allows to
query the hardware context index.
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Acked-by: Jens Axboe <axboe@kernel.dk> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:27:07 +0000 (14:27 +0200)]
scsi: ratelimit I/O error messages
There can be quite a lot of I/O error messages, even on smaller
machines. So we need to ratelimit them to not overwhelm logging.
Signed-off-by: Hannes Reinecke <hare@suse.de> Tested-by: Robert Elliott <elliott@hp.com> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Thu, 30 Oct 2014 08:44:36 +0000 (09:44 +0100)]
scsi: correct return values for .eh_abort_handler implementations
The .eh_abort_handler needs to return SUCCESS, FAILED, or
FAST_IO_FAIL. So fixup all callers to adhere to this requirement.
Reviewed-by: Robert Elliott <elliott@hp.com> Cc: <stable@vger.kernel.org> Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:27:04 +0000 (14:27 +0200)]
scsi: document scsi_try_to_abort_cmd
scsi_try_to_abort_cmd() should only return SUCCESS, FAILED, or
FAST_IO_FAIL. So document that in the function description and simplify
the logging message.
Signed-off-by: Hannes Reinecke <hare@suse.de> Suggested-by: Christoph Hellwig <hch@infradead.org> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:27:03 +0000 (14:27 +0200)]
scsi: use shost argument in scsi_eh_prt_fail_stats
The EH statistics are per host, so we should be using
shost_printk() here.
Signed-off-by: Hannes Reinecke <hare@suse.de> Suggested-by: Robert Elliott <elliott@hp.com> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:27:02 +0000 (14:27 +0200)]
scsi: fixup logging messages in scsi_error.c
Use the matching scope for logging messages to allow for
better command tracing.
Signed-off-by: Hannes Reinecke <hare@suse.de> Suggested-by: Robert Elliott <elliott@hp.com> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:27:00 +0000 (14:27 +0200)]
scsi: remove scsi_show_result()
Open-code scsi_print_result in sd.c, and cleanup logging to
not print duplicate informations.
Also remove the call to scsi_show_result() in ufshcd.c
to be consistent with other callers of scsi_execute().
With that we can remove scsi_show_result in constants.c
Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:26:57 +0000 (14:26 +0200)]
scsi: repurpose the last argument from print_opcode_name()
print_opcode_name() was only ever called with a '0' argument
from LLDDs and ULDs which were _not_ supporting variable length
CDBs, so the 'if' clause was never triggered.
Instead we should be using the last argument to specify
the cdb length to avoid accidental overflow when reading
the cdb buffer.
Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:26:51 +0000 (14:26 +0200)]
scsi: do not decode sense extras
Currently we're only decoding sense extras for tape devices.
And even there only for fixed format sense formats.
As this is of rather limited use in the general case we should
be stop trying to decode sense extras; the tape driver does
its own decoding anyway.
Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:26:50 +0000 (14:26 +0200)]
scsi: stop decoding if scsi_normalize_sense() fails
If scsi_normalize_sense() fails we couldn't decode the sense
buffer, and the scsi_sense_hdr fields are invalid.
For those cases we should rather dump the sense buffer
and not try to decode invalid fields.
Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:26:49 +0000 (14:26 +0200)]
53c700: remove scsi_print_sense() usage
The 53c700 driver would be using scsi_print_sense() in a debug
statement, which was never compiled in. Plus the same information
can get retrieved with logging. So remove it.
Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:26:47 +0000 (14:26 +0200)]
fas216: return DID_ERROR for incomplete data transfer
fas216 returns DID_BAD_TARGET for an incomplete data
transfer. The midlayer uses DID_BAD_TARGET to signal
a non-existing or not reachable target. So we should
rather be using DID_ERROR here.
Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:26:46 +0000 (14:26 +0200)]
acornscsi: use scsi_print_command()
Update acornscsi to use scsi_print_command() instead of the
underscore version and use scmd_printk() in acornscsi_done().
This will add correct device annotations in the resulting message.
And we should be using set_host_byte() for setting the
final result.
Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:26:45 +0000 (14:26 +0200)]
scsi: use sdev as argument for sense code printing
We should be using the standard dev_printk() variants for
sense code printing.
[hch: remove __scsi_print_sense call in xen-scsiback, Acked by Juergen]
[hch: folded bracing fix from Dan Carpenter] Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:26:43 +0000 (14:26 +0200)]
aha152x: debug output update and whitespace cleanup
Remove all uncommented debugging code and move all
printk() statements over to dev_printk().
And while we're at it we should be doing a whitespace
cleanup, too.
Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Some SES devices give non-unique Element Descriptors as part of the
Element Descriptor diag page. Since we use these for creating sysfs
entries, they need to be unique. The specification doesn't require
these to be unique.
Eg:
$ sg_ses -p 7 /dev/sg0
FTS CORP TXS6_SAS20BPX12 0500
enclosure services device
Element descriptor In diagnostic page:
generation code: 0x0
element descriptor by type list
Element type: Array device, subenclosure id: 0
Overall descriptor: ArrayDevicesInSubEnclsr0
Element 1 descriptor: ArrayDevice00
Element 2 descriptor: ArrayDevice01
Element 3 descriptor: ArrayDevice02
Element 4 descriptor: ArrayDevice03
Element 5 descriptor: ArrayDevice03
Element 6 descriptor: ArrayDevice03
Element 7 descriptor: ArrayDevice03
Element 8 descriptor: ArrayDevice03
Element 9 descriptor: ArrayDevice03
Element 10 descriptor: ArrayDevice03
Element 11 descriptor: ArrayDevice03
Element 12 descriptor: ArrayDevice03
Based on http://thread.gmane.org/gmane.linux.scsi/69289. This
version implements James' ideas about the naming convention
Signed-off-by: Markus Stockhausen <stockhausen@collogia.de> Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Laurence Oberman [Sun, 19 Oct 2014 13:44:25 +0000 (09:44 -0400)]
st: add a debug_flag module parameter request
This patch adds a debug_flag parameter that can be set on module load, and allows the DEBUG facility without a module recompile.
Note that now DEBUG 1 is the default with this patch.
Usage: modprobe st debug_flag=1
Signed-off-by: Laurence Oberman <loberman@redhat.com> Acked-by: Kai M??kisara <kai.makisara@kolumbus.fi> Signed-off-by: Christoph Hellwig <hch@lst.de>
Douglas Gilbert [Sat, 18 Oct 2014 20:11:21 +0000 (22:11 +0200)]
scsi: add SG_SCSI_RESET_NO_ESCALATE flag to SG_SCSI_RESET ioctl
Further to a January 2013 thread titled: "[PATCH] SG_SCSI_RESET ioctl
should only perform requested operation" by Jeremy Linton a patch (v3)
is presented that expands the existing ioctl to include "no_escalate"
versions to the existing resets. This requires no changes to SCSI low
level drivers (LLDs); it adds several more finely tuned reset options
to the user space. For example:
/* This call remains the same, with the same escalating semantics
* if the device (LU) reset fail. That is: on failure to try a
* target reset and if that fails, try a bus reset, and if that fails
* try a host (i.e. LLD) reset. */
val = SG_SCSI_RESET_DEVICE;
res = ioctl(<sg_or_block_fd>, SG_SCSI_RESET, &val);
/* What follows is a new option introduced by this patch series. Only
* a device reset is attempted. If that fails then an appropriate
* error code is provided. N.B. There is no reset escalation. */
val = SG_SCSI_RESET_DEVICE | SG_SCSI_RESET_NO_ESCALATE;
res = ioctl(<sg_or_block_fd>, SG_SCSI_RESET, &val);
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com> Reviewed-by: Jeremy Linton <jlinton@tributary.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
As sparse correctly pointed out, scsi_partsize should use get_unaligned_le32
to read PC partition tables from disk, as they are little endian.
The result of this bug is that we returned incorrect geometries on big
endian systems when using the scsicam variant. Which probably doesn't
matter as only old x86 systems every cared about the geometry.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
Mark Rustad [Tue, 14 Oct 2014 13:38:53 +0000 (06:38 -0700)]
scsi: resolve some missing-field-initializers warnings
Resolve some missing-field-initializers warnings by using
designated initialization.
[hch: W=2 with modern gcc warns about this. Pretty pointless to me, but
I'd prefer to keep us warning free]
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Mark Knibbs [Thu, 9 Oct 2014 11:39:48 +0000 (12:39 +0100)]
scsi: fix off-by-one LUN check in scsi_scan_host_selected()
The Scsi_Host structure max_lun field is the maximum allowed LUN plus 1. So
a LUN value is invalid if >= max_lun.
Signed-off-by: Mark Knibbs <markk@clara.co.uk> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Mark Knibbs [Thu, 9 Oct 2014 11:39:40 +0000 (12:39 +0100)]
scsi: fix trivial typos in scsi_scan.c comment
Signed-off-by: Mark Knibbs <markk@clara.co.uk> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
bnx2fc_queuecommand(): when allocating a new io_req, the tgt_lock
spinlock must be locked before calling bnx2fc_cmd_alloc().
The spinlock should also be kept locked until bnx2fc_post_io_req() has
been completed.
If not, a kernel thread may call bnx2fc_process_cq_compl() that extracts
the newly allocated io_req from hba->cmd_mgr->cmds and destroys it while
it is still being used by bnx2fc_post_io_req().
Jiang Liu [Mon, 3 Nov 2014 12:44:20 +0000 (20:44 +0800)]
megaraid_sas: fix bug in handling return value of pci_enable_msix_range()
Function pci_enable_msix_range() may return negative values for error
conditions. So it's a bug by checking (pci_enable_msix_range() != 0)
for success and causes failure to megaraid driver when MSI is disabled.
[ 16.487267] megaraid_sas 0000:02:00.0: Controller type: iMR
[ 16.487275] genirq: Flags mismatch irq 0. 00000000 (megasas) vs. 00015a00 (tii
mer)
[ 16.487347] megasas: Failed to register IRQ for vector 0.
Fixes: 8ae80ed1734b "megaraid: Use pci_enable_msix_range() instead of pci_enable_msix()" Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Acked-by: Sumit Saxena <sumit.saxena@avagotech.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: <stable@vger.kernel.org> # 3.17
scsi: TUR path is down after adapter gets reset with multipath
This patch fixes an issue with multipath ipr SAS devices which require a
start unit command to be issued following an adapter reset. Without this
patch, paths get marked failed following an adapter reset and since the
error handler never gets invoked to issue the start unit, the paths are
never recovered. Returning FAILED for this case ensures the error
handler wakes up to issue the start unit.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
Multipath devices using the TUR path checker need to see the sense
code for a failed TUR command in their device handler. Since commit 14216561e164671ce147458653b1fea06a we always return success for mid
layer issued TUR commands before calling the device handler, which
stopped the TUR path checker from working.
Move the call to the device handler check sense method before the early
return for TUR commands to give the device handler a chance to intercept
them.
Signed-off-by: Christoph Hellwig <hch@infradead.org> Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
scsi: only re-lock door after EH on devices that were reset
Setups that use the blk-mq I/O path can lock up if a host with a single
device that has its door locked enters EH. Make sure to only send the
command to re-lock the door to devices that actually were reset and thus
might have lost their state. Otherwise the EH code might be get blocked
on blk_get_request as all requests for non-reset devices might be in use.
Cc: stable@vger.kernel.org Signed-off-by: Christoph Hellwig <hch@lst.de> Reported-by: Meelis Roos <meelis.roos@ut.ee> Tested-by: Meelis Roos <meelis.roos@ut.ee> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Linus Torvalds [Sun, 9 Nov 2014 22:49:56 +0000 (14:49 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- enable bpf syscall for compat
- cpu_suspend fix when checking the idle state type
- defconfig update
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: defconfig: update defconfig for 3.18
arm64: compat: Enable bpf syscall
arm64: psci: fix cpu_suspend to check idle state type for index
Linus Torvalds [Sun, 9 Nov 2014 22:46:36 +0000 (14:46 -0800)]
Merge tag 'armsoc-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another quiet week:
- a fix to silence edma probe error on non-supported platforms from
Arnd
- a fix to enable the PL clock for Parallella, to make mainline
usable with the SDK.
- a somewhat verbose fix for the PLL clock tree on VF610
- enabling of SD/MMC on one of the VF610-based boards (for testing)
- a fix for i.MX where CONFIG_SPI used to be implicitly enabled and
now needs to be added to the defconfig instead
- another maintainer added for bcm2835: Lee Jones"
* tag 'armsoc-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: zynq: Enable PL clocks for Parallella
dma: edma: move device registration to platform code
ARM: dts: vf610: add SD node to cosmic dts
MAINTAINERS: update bcm2835 entry
ARM: imx: Fix the removal of CONFIG_SPI option
ARM: imx: clk-vf610: define PLL's clock tree
Linus Torvalds [Sun, 9 Nov 2014 22:30:24 +0000 (14:30 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fix from Chris Mason:
"It's a one liner for an error cleanup path that leads to crashes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix kfree on list_head in btrfs_lookup_csums_range error cleanup
Linus Torvalds [Sun, 9 Nov 2014 22:11:58 +0000 (14:11 -0800)]
Merge tag 'driver-core-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are 3 tiny fixes for 3.18-rc4.
One fixes up a long-stading race condition in the driver core for
removing directories in /sys/devices/virtual/ and the other 2 fix up
the wording of a new Kconfig option that was added in 3.18-rc1"
* tag 'driver-core-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
tiny: reverse logic for DISABLE_DEV_COREDUMP
sysfs: driver core: Fix glue dir race condition by gdp_mutex
Linus Torvalds [Sun, 9 Nov 2014 22:11:07 +0000 (14:11 -0800)]
Merge tag 'staging-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some staging/iio fixes for 3.18-rc4.
Nothing major, just a few bugfixes of things that have been reported"
* tag 'staging-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging:iio:ade7758: Remove "raw" from channel name
staging:iio:ade7758: Fix check if channels are enabled in prenable
staging:iio:ade7758: Fix NULL pointer deref when enabling buffer
iio: as3935: allocate correct iio_device size
io: accel: kxcjk-1013: Fix iio_event_spec direction
iio: tsl4531: Fix compiler error when CONFIG_PM_OPS is not defined
iio: adc: mxs-lradc: Disable the clock on probe failure
iio: st_sensors: Fix buffer copy
staging:iio:ad5933: Drop "raw" from channel names
staging:iio:ad5933: Fix NULL pointer deref when enabling buffer
Linus Torvalds [Sun, 9 Nov 2014 22:07:30 +0000 (14:07 -0800)]
Merge tag 'tty-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tiny serial/tty fixes for 3.18-rc4 that resolve some
reported issues"
* tag 'tty-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix pty master poll() after slave closes v2
serial: of-serial: fix uninitialized kmalloc variable
tty/vt: don't set font mappings on vc not supporting this
tty: serial: 8250_mtk: Fix quot calculation
tty: Prevent "read/write wait queue active!" log flooding
tty: Fix high cpu load if tty is unreleaseable
serial: Fix divide-by-zero fault in uart_get_divisor()
Linus Torvalds [Sun, 9 Nov 2014 22:05:53 +0000 (14:05 -0800)]
Merge tag 'usb-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 3.18-rc4.
Just a bunch of little fixes resolving reported issues and new device
ids for existing drivers. Full details are in the shortlog"
* tag 'usb-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
USB: Update default usb-storage delay_use value in kernel-parameters.txt
USB: cdc-acm: add quirk for control-line state requests
phy: omap-usb2: Enable runtime PM of omap-usb2 phy properly
USB: storage: Fix timeout in usb_stor_euscsi_init() and usb_stor_huawei_e220_init()
USB: cdc-acm: only raise DTR on transitions from B0
Revert "storage: Replace magic number with define in usb_stor_euscsi_init()"
usb: core: notify disconnection when core detects disconnect
usb: core: need to call usb_phy_notify_connect after device setup
uas: Add US_FL_NO_ATA_1X quirk for 2 more Seagate models
xhci: no switching back on non-ULT Haswell
USB: quirks: enable device-qualifier quirk for yet another Elan touchscreen
USB: quirks: enable device-qualifier quirk for another Elan touchscreen
MAINTAINERS: Remove duplicate entry for usbip driver
usb: storage: fix build warnings !CONFIG_PM
usb: Remove references to non-existent PLAT_S5P symbol
uas: Add NO_ATA_1X for VIA VL711 devices
xhci: Disable streams on Asmedia 1042 xhci controllers
USB: HWA: fix a warning message
uas: Add US_FL_NO_ATA_1X quirk for 1 more Seagate model
usb-storage: handle a skipped data phase
...
Andreas Färber [Thu, 6 Nov 2014 17:22:10 +0000 (18:22 +0100)]
ARM: dts: zynq: Enable PL clocks for Parallella
The Parallella board comes with a U-Boot bootloader that loads one of
two predefined FPGA bitstreams before booting the kernel. Both define an
AXI interface to the on-board Epiphany processor.
Enable clocks FCLK0..FCLK3 for the Programmable Logic by default.
Otherwise accessing, e.g., the ESYSRESET register freezes the board,
as seen with the Epiphany SDK tools e-reset and e-hw-rev, using /dev/mem.
Cc: <stable@vger.kernel.org> # 3.17.x Signed-off-by: Andreas Färber <afaerber@suse.de> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Sat, 8 Nov 2014 17:32:29 +0000 (09:32 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c bugfixes from Wolfram Sang:
"One bigger cleanup (FSF address removal) and two bugfixes for I2C"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: Dispose OF IRQ mapping at client removal time
i2c: at91: don't account as iowait
i2c: remove FSF address
Pull media fixes from Mauro Carvalho Chehab:
"For:
- some regression fixes at the Remote Controller core and imon driver
- a build fix for certain randconfigs with ir-hix5hd2
- don't feed power to satellite system at ds3000 driver init
It also contains some fixes for drivers added for Kernel 3.18:
- some fixes at the new ISDB-S driver, and the corresponding bits to
fix some descriptors for this Japanese TV standard at the DVB core
- two warning cleanups for sp2 driver if PM is disabled
- change the default mode for the new vivid driver"
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] sp2: sp2_init() can be static
[media] dvb:tc90522: fix always-false expression
[media] dvb-core: set default properties of ISDB-S
[media] dvb:tc90522: fix stats report
[media] vivid: default to single planar device instances
[media] imon: fix other RC type protocol support
[media] ir-hix5hd2 fix build warning
[media] ds3000: fix LNB supply voltage on Tevii S480 on initialization
[media] rc5-decoder: BZ#85721: Fix RC5-SZ decoding
[media] rc-core: fix protocol_change regression in ir_raw_event_register
Linus Torvalds [Sat, 8 Nov 2014 02:08:02 +0000 (18:08 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"This weeks' round of MIPS bug fixes for 3.18:
- wire up the bpf syscall
- fix TLB dump output for R3000 class TLBs
- fix strnlen_user return value if no NUL character was found.
- fix build with binutils 2.24.51+. While there is no binutils 2.25
release yet, toolchains derived from binutils 2.24.51+ are already
in common use.
- the Octeon GPIO code forgot to offline GPIO IRQs.
- fix build error for XLP.
- fix possible BUG assertion with EVA for CMA"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix build with binutils 2.24.51+
MIPS: R3000: Fix debug output for Virtual page number
MIPS: Fix strnlen_user() return value in case of overlong strings.
MIPS: CMA: Do not reserve memory if not required
MIPS: Wire up bpf syscall.
MIPS/Xlp: Remove the dead function destroy_irq() to fix build error
MIPS: Octeon: Make Octeon GPIO IRQ chip CPU hotplug-aware
Linus Torvalds [Fri, 7 Nov 2014 22:08:13 +0000 (14:08 -0800)]
Merge tag 'xfs-for-linus-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"This update fixes a warning in the new pagecache_isize_extended() and
updates some related comments, another fix for zero-range
misbehaviour, and an unforntuately large set of fixes for regressions
in the bulkstat code.
The bulkstat fixes are large but necessary. I wouldn't normally push
such a rework for a -rcX update, but right now xfsdump can silently
create incomplete dumps on 3.17 and it's possible that even xfsrestore
won't notice that the dumps were incomplete. Hence we need to get
this update into 3.17-stable kernels ASAP.
In more detail, the refactoring work I committed in 3.17 has exposed a
major hole in our QA coverage. With both xfsdump (the major user of
bulkstat) and xfsrestore silently ignoring missing files in the
dump/restore process, incomplete dumps were going unnoticed if they
were being triggered. Many of the dump/restore filesets were so small
that they didn't evenhave a chance of triggering the loop iteration
bugs we introduced in 3.17, so we didn't exercise the code
sufficiently, either.
We have already taken steps to improve QA coverage in xfstests to
avoid this happening again, and I've done a lot of manual verification
of dump/restore on very large data sets (tens of millions of inodes)
of the past week to verify this patch set results in bulkstat behaving
the same way as it does on 3.16.
Unfortunately, the fixes are not exactly simple - in tracking down the
problem historic API warts were discovered (e.g xfsdump has been
working around a 20 year old bug in the bulkstat API for the past 10
years) and so that complicated the process of diagnosing and fixing
the problems. i.e. we had to fix bugs in the code as well as
discover and re-introduce the userspace visible API bugs that we
unwittingly "fixed" in 3.17 that xfsdump relied on to work correctly.
Summary:
- incorrect warnings about i_mutex locking in pagecache_isize_extended()
and updates comments to match expected locking
- another zero-range bug fix for stray file size updates
- a bunch of fixes for regression in the bulkstat code introduced in
3.17"
* tag 'xfs-for-linus-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: track bulkstat progress by agino
xfs: bulkstat error handling is broken
xfs: bulkstat main loop logic is a mess
xfs: bulkstat chunk-formatter has issues
xfs: bulkstat chunk formatting cursor is broken
xfs: bulkstat btree walk doesn't terminate
mm: Fix comment before truncate_setsize()
xfs: rework zero range to prevent invalid i_size updates
mm: Remove false WARN_ON from pagecache_isize_extended()
xfs: Check error during inode btree iteration in xfs_bulkstat()
xfs: bulkstat doesn't release AGI buffer on error
Linus Torvalds [Fri, 7 Nov 2014 19:55:47 +0000 (11:55 -0800)]
Merge tag 'regulator-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"More changes than I'd like here, most of them for a single bug
repeated in a bunch of drivers with data not being initialized
correctly, plus a fix to lower the severity of a warning introduced in
the last merge window which can legitimately go off so we don't want
to alarm users excessively"
* tag 'regulator-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: s2mpa01: zero-initialize regulator match table array
regulator: max8660: zero-initialize regulator match table array
regulator: max77802: zero-initialize regulator match table
regulator: max77686: zero-initialize regulator match table
regulator: max1586: zero-initialize regulator match table array
regulator: max77693: Fix use of uninitialized regulator config
regulator: of: Lower the severity of the error with no container
Linus Torvalds [Fri, 7 Nov 2014 19:54:44 +0000 (11:54 -0800)]
Merge tag 'spi-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi bugfixes from Mark Brown:
"A couple of small driver fixes for v3.18, both quite problematic if
you hit a use case that's affected"
* tag 'spi-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: pxa2xx: toggle clocks on suspend if not disabled by runtime PM
spi: fsl-dspi: Fix CTAR selection
Johannes Berg [Thu, 30 Oct 2014 09:00:35 +0000 (10:00 +0100)]
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
The ENABLE_DEV_COREDUMP option is misleading as it implies that
it gets the framework enabled, this isn't true it just allows it
to get enabled if a driver needs it.
Rename it to ALLOW_DEV_COREDUMP to better capture its semantics.
Aristeu Rozanski [Thu, 16 Oct 2014 15:49:49 +0000 (11:49 -0400)]
tiny: reverse logic for DISABLE_DEV_COREDUMP
It's desirable for allnconfig and tinyconfig targets to result in the
least amount of code possible. DISABLE_DEV_COREDUMP exists as a way to
switch off DEV_COREDUMP regardless if any drivers select
WANT_DEV_COREDUMP.
This patch renames the option to ENABLE_DEV_COREDUMP and setting it to
'n' (as in allnconfig or tinyconfig) will effectively disable device
coredump.
Mark Knibbs [Tue, 4 Nov 2014 13:00:15 +0000 (13:00 +0000)]
USB: Update default usb-storage delay_use value in kernel-parameters.txt
Back in 2010 the default usb-storage delay_use time was reduced from 5 to 1
second (commit a4a47bc03fe520e95e0c4212bf97c86545fb14f9), but
kernel-parameters.txt wasn't updated to reflect that.
Signed-off-by: Mark Knibbs <markk@clara.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yijing Wang [Fri, 7 Nov 2014 04:05:49 +0000 (12:05 +0800)]
sysfs: driver core: Fix glue dir race condition by gdp_mutex
There is a race condition when removing glue directory.
It can be reproduced in following test:
path 1: Add first child device
device_add()
get_device_parent()
/*find parent from glue_dirs.list*/
list_for_each_entry(k, &dev->class->p->glue_dirs.list, entry)
if (k->parent == parent_kobj) {
kobj = kobject_get(k);
break;
}
....
class_dir_create_and_add()
path2: Remove last child device under glue dir
device_del()
cleanup_device_parent()
cleanup_glue_dir()
kobject_put(glue_dir);
If path2 has been called cleanup_glue_dir(), but not
call kobject_put(glue_dir), the glue dir is still
in parent's kset list. Meanwhile, path1 find the glue
dir from the glue_dirs.list. Path2 may release glue dir
before path1 call kobject_get(). So kernel will report
the warning and bug_on.
This is a "classic" problem we have of a kref in a list
that can be found while the last instance could be removed
at the same time.
This patch reuse gdp_mutex to fix this race condition.
The following calltrace is captured in kernel 3.4, but
the latest kernel still has this bug.
Manuel Lauss [Fri, 7 Nov 2014 13:13:54 +0000 (14:13 +0100)]
MIPS: Fix build with binutils 2.24.51+
Starting with version 2.24.51.20140728 MIPS binutils complain loudly
about mixing soft-float and hard-float object files, leading to this
build failure since GCC is invoked with "-msoft-float" on MIPS:
To fix this, we detect if GAS is new enough to support "-msoft-float" command
option, and if it does, we can let GCC pass it to GAS; but then we also need
to sprinkle the files which make use of floating point registers with the
necessary ".set hardfloat" directives.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Cc: Linux-MIPS <linux-mips@linux-mips.org> Cc: Matthew Fortune <Matthew.Fortune@imgtec.com> Cc: Markos Chandras <Markos.Chandras@imgtec.com> Cc: Maciej W. Rozycki <macro@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8355/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Dave Chinner [Thu, 6 Nov 2014 21:33:52 +0000 (08:33 +1100)]
xfs: track bulkstat progress by agino
The bulkstat main loop progress is tracked by the "lastino"
variable, which is a full 64 bit inode. However, the loop actually
works on agno/agino pairs, and so there's a significant disconnect
between the rest of the loop and the main cursor. Convert this to
use the agino, and pass the agino into the chunk formatting function
and convert it too.
This gets rid of the inconsistency in the loop processing, and
finally makes it simple for us to skip inodes at any point in the
loop simply by incrementing the agino cursor.
cc: <stable@vger.kernel.org> # 3.17 Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Thu, 6 Nov 2014 21:31:15 +0000 (08:31 +1100)]
xfs: bulkstat error handling is broken
The error propagation is a horror - xfs_bulkstat() returns
a rval variable which is only set if there are formatter errors. Any
sort of btree walk error or corruption will cause the bulkstat walk
to terminate but will not pass an error back to userspace. Worse
is the fact that formatter errors will also be ignored if any inodes
were correctly formatted into the user buffer.
Hence bulkstat can fail badly yet still report success to userspace.
This causes significant issues with xfsdump not dumping everything
in the filesystem yet reporting success. It's not until a restore
fails that there is any indication that the dump was bad and tha
bulkstat failed. This patch now triggers xfsdump to fail with
bulkstat errors rather than silently missing files in the dump.
This now causes bulkstat to fail when the lastino cookie does not
fall inside an existing inode chunk. The pre-3.17 code tolerated
that error by allowing the code to move to the next inode chunk
as the agino target is guaranteed to fall into the next btree
record.
With the fixes up to this point in the series, xfsdump now passes on
the troublesome filesystem image that exposes all these bugs.
cc: <stable@vger.kernel.org> Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com>
Dave Chinner [Thu, 6 Nov 2014 21:31:13 +0000 (08:31 +1100)]
xfs: bulkstat main loop logic is a mess
There are a bunch of variables tha tare more wildy scoped than they
need to be, obfuscated user buffer checks and tortured "next inode"
tracking. This all needs cleaning up to expose the real issues that
need fixing.
cc: <stable@vger.kernel.org> # 3.17 Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Thu, 6 Nov 2014 21:30:58 +0000 (08:30 +1100)]
xfs: bulkstat chunk-formatter has issues
The loop construct has issues:
- clustidx is completely unused, so remove it.
- the loop tries to be smart by terminating when the
"freecount" tells it that all inodes are free. Just drop
it as in most cases we have to scan all inodes in the
chunk anyway.
- move the "user buffer left" condition check to the only
point where we consume space int eh user buffer.
- move the initialisation of agino out of the loop, leaving
just a simple loop control logic using the clusteridx.
Also, double handling of the user buffer variables leads to problems
tracking the current state - use the cursor variables directly
rather than keeping local copies and then having to update the
cursor before returning.
cc: <stable@vger.kernel.org> # 3.17 Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Thu, 6 Nov 2014 21:30:30 +0000 (08:30 +1100)]
xfs: bulkstat chunk formatting cursor is broken
The xfs_bulkstat_agichunk formatting cursor takes buffer values from
the main loop and passes them via the structure to the chunk
formatter, and the writes the changed values back into the main loop
local variables. Unfortunately, this complex dance is full of corner
cases that aren't handled correctly.
The biggest problem is that it is double handling the information in
both the main loop and the chunk formatting function, leading to
inconsistent updates and endless loops where progress is not made.
To fix this, push the struct xfs_bulkstat_agichunk outwards to be
the primary holder of user buffer information. this removes the
double handling in the main loop.
Also, pass the last inode processed by the chunk formatter as a
separate parameter as it purely an output variable and is not
related to the user buffer consumption cursor.
Finally, the chunk formatting code is not shared by anyone, so make
it local to xfs_itable.c.
cc: <stable@vger.kernel.org> # 3.17 Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Thu, 6 Nov 2014 21:29:57 +0000 (08:29 +1100)]
xfs: bulkstat btree walk doesn't terminate
The bulkstat code has several different ways of detecting the end of
an AG when doing a walk. They are not consistently detected, and the
code that checks for the end of AG conditions is not consistently
coded. Hence the are conditions where the walk code can get stuck in
an endless loop making no progress and not triggering any
termination conditions.
Convert all the "tmp/i" status return codes from btree operations
to a common name (stat) and apply end-of-ag detection to these
operations consistently.
cc: <stable@vger.kernel.org> # 3.17 Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com>
Jan Kara [Thu, 6 Nov 2014 21:29:25 +0000 (08:29 +1100)]
mm: Fix comment before truncate_setsize()
XFS doesn't always hold i_mutex when calling truncate_setsize() and it
uses a different lock to serialize truncates and writes. So fix the
comment before truncate_setsize().
Reported-by: Jan Beulich <JBeulich@suse.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Dave Chinner <david@fromorbit.com>
Johan Hovold [Thu, 6 Nov 2014 17:08:33 +0000 (18:08 +0100)]
USB: cdc-acm: add quirk for control-line state requests
Add new quirk for devices that cannot handle control-line state
requests.
Note that we currently send these requests to all devices, regardless of
whether they claim to support it, but that errors are only logged if
support is claimed.
Since commit 0943d8ead30e ("USB: cdc-acm: use tty-port dtr_rts"), which
only changed the timings for these requests slightly, this has been
reported to cause occasional firmware crashes on Simtec Electronics
Entropy Key devices after re-enumeration. Enable the quirk for this
device.
Merge tag 'fixes-for-v3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.18-rc4
A single fix this for dwc2 this time. Because of
excessive debugging messages, dwc2 would sometimes
fail enumeration. The fix is simple, just converting
a dev_info() into dev_dbg().
Commit f95499c3030f ("n_tty: Don't wait for buffer work in read() loop")
introduces a race window where a pty master can be signalled that the pty
slave was closed before all the data that the slave wrote is delivered.
Commit f8747d4a466a ("tty: Fix pty master read() after slave closes") fixed the
problem in case of n_tty_read, but the problem still exists for n_tty_poll.
This can be seen by running 'for ((i=0; i<100;i++));do ./test.py ;done'
where test.py is:
import os, select, pty
(pid, pty_fd) = pty.fork()
if pid == 0:
os.write(1, 'This string should be received by parent')
else:
poller = select.epoll()
poller.register( pty_fd, select.EPOLLIN )
ready = poller.poll( 1 * 1000 )
for fd, events in ready:
if not events & select.EPOLLIN:
print 'missed POLLIN event'
else:
print os.read(fd, 100)
poller.close()
The string from the slave is missed several times.
This patch takes the same approach as the fix for read and special cases
this condition for poll.
Tested on 3.16.
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Thu, 6 Nov 2014 19:33:06 +0000 (11:33 -0800)]
Merge tag 'pci-v3.18-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"This fixes an oops when enabling SR-IOV VF devices. The oops is a
regression I added by configuring all devices during enumeration.
- Don't oops on virtual buses in acpi_pci_get_bridge_handle() (Yinghai Lu)"
* tag 'pci-v3.18-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Don't oops on virtual buses in acpi_pci_get_bridge_handle()
Linus Torvalds [Thu, 6 Nov 2014 19:31:32 +0000 (11:31 -0800)]
Merge tag 'sound-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This update contains mostly only fixes for Realtek HD-audio codec
driver in addition to a long-standing sysfs warning bug fix for
USB-audio.
One significant fix for Realtek codecs is the update of EAPD init
codes. This avoids invalid COEF setups for some codec models and may
fix "lost sound" in some cases.
The rest are a bit high volume but only new quirks and ALC668-specific
COEF tables"
* tag 'sound-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Restore default value for ALC668
ALSA: usb-audio: Fix device_del() sysfs warnings at disconnect
ALSA: hda - fix mute led problem for three HP laptops
ALSA: hda/realtek - Update Initial AMP for EAPD control
ALSA: hda - change three SSID quirks to one pin quirk
ALSA: hda - Set GPIO 4 low for a few HP machines
ALSA: hda - Add ultra dock support for Thinkpad X240.
Isamu Mogi [Thu, 30 Oct 2014 13:07:36 +0000 (22:07 +0900)]
MIPS: R3000: Fix debug output for Virtual page number
Virtual page number of R3000 in entryhi is 20 bit from MSB. But in
dump_tlb(), the bit mask to read it from entryhi is 19 bit (0xffffe000).
The patch fixes that to 0xfffff000.
spi: pxa2xx: toggle clocks on suspend if not disabled by runtime PM
If PM_RUNTIME is enabled, it is easy to trigger the following backtrace
on pxa2xx hosts:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at /home/lumag/linux/arch/arm/mach-pxa/clock.c:35 clk_disable+0xa0/0xa8()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-00007-g1b3d2ee-dirty #104
[<c000de68>] (unwind_backtrace) from [<c000c078>] (show_stack+0x10/0x14)
[<c000c078>] (show_stack) from [<c001d75c>] (warn_slowpath_common+0x6c/0x8c)
[<c001d75c>] (warn_slowpath_common) from [<c001d818>] (warn_slowpath_null+0x1c/0x24)
[<c001d818>] (warn_slowpath_null) from [<c0015e80>] (clk_disable+0xa0/0xa8)
[<c0015e80>] (clk_disable) from [<c02507f8>] (pxa2xx_spi_suspend+0x2c/0x34)
[<c02507f8>] (pxa2xx_spi_suspend) from [<c0200360>] (platform_pm_suspend+0x2c/0x54)
[<c0200360>] (platform_pm_suspend) from [<c0207fec>] (dpm_run_callback.isra.14+0x2c/0x74)
[<c0207fec>] (dpm_run_callback.isra.14) from [<c0209254>] (__device_suspend+0x120/0x2f8)
[<c0209254>] (__device_suspend) from [<c0209a94>] (dpm_suspend+0x50/0x208)
[<c0209a94>] (dpm_suspend) from [<c00455ac>] (suspend_devices_and_enter+0x8c/0x3a0)
[<c00455ac>] (suspend_devices_and_enter) from [<c0045ad4>] (pm_suspend+0x214/0x2a8)
[<c0045ad4>] (pm_suspend) from [<c04b5c34>] (test_suspend+0x14c/0x1dc)
[<c04b5c34>] (test_suspend) from [<c000880c>] (do_one_initcall+0x8c/0x1fc)
[<c000880c>] (do_one_initcall) from [<c04aecfc>] (kernel_init_freeable+0xf4/0x1b4)
[<c04aecfc>] (kernel_init_freeable) from [<c0378078>] (kernel_init+0x8/0xec)
[<c0378078>] (kernel_init) from [<c0009590>] (ret_from_fork+0x14/0x24)
---[ end trace 46524156d8faa4f6 ]---
This happens because suspend function tries to disable a clock that is
already disabled by runtime_suspend callback. Add if
(!pm_runtime_suspended()) checks to suspend/resume path.
Fixes: 7d94a505858 (spi/pxa2xx: add support for runtime PM) Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Reported-by: Andrea Adami <andrea.adami@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org
The info pointer points to an uninitialized kmalloced space.
If a device doesn't have clk property, then info->clk may
have unpredicated value and cause call trace. So use kzalloc
to make sure it is NULL initialized.