Helmut Schaa [Sun, 30 Jan 2011 12:16:52 +0000 (13:16 +0100)]
rt2x00: Limit beacon updates in bss_info_changed to USB devices
Currently there are two places that trigger a beacon update on PCI
devices. The bss_info_changed callback and the periodic update
triggered by the TBTT or PRETBTT interrupt.
Since the next TBTT or PRETBTT interrupt will periodically fetch an
updated beacon remove the update_beacon call in the bss_info_changed
callback for PCI devices.
In the worst case it will take one beacon interval longer to fetch
the new beacon then before. For devices that have a PRETBTT interrupt
there should be no change at all.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sun, 30 Jan 2011 12:16:28 +0000 (13:16 +0100)]
rt2x00: Introduce beacon_update_locked that requires caller locking
Introduce a beacon_update_locked function that does not acquire the
according beacon mutex to allow beacon updates from atomic context. The
caller has to take care of synchronization.
No functional changes. Just preparation for beacon updates from tasklet
context.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sun, 30 Jan 2011 12:16:03 +0000 (13:16 +0100)]
rt2x00: Refactor beacon code to make use of start- and stop_queue
This patch allows to dynamically remove beaconing interfaces without
shutting beaconing down on all interfaces.
The only place to start and stop beaconing are now the start- and
stop_queue callbacks. Hence, we can remove some register writes during
interface bring up (config_intf) and only write the correct sync mode
to the register there.
When multiple beaconing interfaces are present we should enable
beaconing as soon as mac80211 enables beaconing on at least one of
them. The beacon queue gets stopped when the last beaconing
interface was stopped by mac80211. Therefore, introduce another
interface counter to keep track ot the number of enabled beaconing
interfaces and start or stop the beacon queue accordingly.
To allow single interfaces to stop beaconing, add a new driver
callback clear_beacon to clear a single interface's beacon without
affecting the other interfaces. Don't overload the clear_entry callback
for clearing beacons as that would introduce additional overhead
(check for each TX queue) into the clear_entry callback which is used
on the drivers TX/RX hotpaths.
Furthermore, the write beacon callback doesn't need to enable beaconing
anymore but since beaconing should be disabled while a new beacon is
written or cleared we still disable beacon generation and enable it
afterwards again in the driver specific callbacks. However, beacon
related interrupts should not be disabled/enabled here, that's solely
done from the start- and stop queue callbacks. It would be nice to stop
the beacon queue just before the beacon update and enable it afterwards
in rt2x00queue itself instead of the current implementation that relies
on the driver doing the right thing. However, since start- and
stop_queue are mutex protected we cannot use them for atomic beacon
updates.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
We use priv->cfg->bt_params && priv->cfg->bt_params->bt_statistics
conditional in few places, merge it into one function.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never set STATUS_SCANNING in softwre scanning mode, disable_hw_scan
check is unneeded. Correct debug message while at it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
We use priv->cfg->bt_params && priv->cfg->bt_params->advanced_bt_coexist
conditional in few places, merge it into one function.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
struct iwl_queue is not part of firmware interface, so __packed is not
needed. Remove it since is may affect performance.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar change as we already do for agn, need to avoid
"Error setting Tx power (-5)" message when loading module.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: do not set tx power when channel is changing
Mac80211 can request for tx power and channel change in one ->config
call. If that happens, *_send_tx_power functions will try to setup tx
power for old channel, what can be not correct because we already change
the band. I.e error "Failed to get channel info for channel 140 [0]",
can be printed frequently when operating in software scanning mode.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Fri, 28 Jan 2011 14:17:11 +0000 (15:17 +0100)]
net/wireless/nl80211.c: Avoid call to genlmsg_cancel
genlmsg_cancel subtracts some constants from its second argument before
calling nlmsg_cancel. nlmsg_cancel then calls nlmsg_trim on the same
arguments. nlmsg_trim tests for NULL before doing any computation, but a
NULL second argument to genlmsg_cancel is no longer NULL due to the initial
subtraction. Nothing else happens in this execution, so the call to
genlmsg_cancel is simply unnecessary in this case.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
Bruno Randolf [Fri, 28 Jan 2011 07:52:11 +0000 (16:52 +0900)]
ath5k: Fix short and long retry configuration
The register definition for retry configuration on AR5212 was wrong, and simply
copied over from AR5210. Update the register definitions from the documentation.
Let the short and long retries be configured from mac80211 and use the standard
values of 7 and 4 by default. Also we need to make sure we don't export more
retries than we are configured for to mac80211 (and the rate module) in
hw->max_rate_tries.
Also clean up the code by removing unused defines and variables and drop the
different values for "station retries" - if these need to be different it can
be handled tru ah_retry_long/short.
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vivek Natarajan [Thu, 27 Jan 2011 09:15:08 +0000 (14:45 +0530)]
ath9k: Fix a PLL hang issue observed with AR9485.
When this PLL hang issue is seen, both Rx and Tx fail to work.
The sqsum_dvc needs to be below 2000 for a good chip. During
this issue the sqsum_dvc value is beyond 80000 and only a
full reset can solve this problem.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 26 Jan 2011 17:23:27 +0000 (18:23 +0100)]
ath9k: use split rx buffers to get rid of order-1 skb allocations
With this change, less CPU time is spent trying to look for consecutive
pages for rx skbs. This also reduces the socket memory required for IP/UDP
reassembly.
Only two buffers per frame are supported. Frames spanning more buffers
will be dropped, but the buffer size is enough to handle the required
AMSDU size.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Wed, 26 Jan 2011 16:29:18 +0000 (21:59 +0530)]
ath9k_hw: Fix INI fixup
Commit "ath9k_hw: move AR9280 PCI EEPROM fix to eeprom_def.c"
changed the behavior of INI overriding which is needed only
for PCI cards. Revert to the original check.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Wed, 26 Jan 2011 16:29:05 +0000 (21:59 +0530)]
ath9k_hw: Fix opmode initialization
Commit "ath9k_hw: Relocate Opmode initialization"
moved the opmode initialization before the STA_ID1 register
was programmed with defaults. This changed the original
behaviour because the re-programming code doesn't take into
account the existing value in the register. Both ath9k and ath9k_htc
were not affected by this change because the opmode is
re-initialized after every reset, when RX is started.
Revert to the original behavior, except keep it outside the
REGWRITE block. This would help remove extraneous opmode calls
in the driver core.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Tue, 25 Jan 2011 10:21:22 +0000 (12:21 +0200)]
cfg80211: Allow non-zero indexes for device specific pair-wise ciphers
Some vendor specific cipher suites require non-zero key indexes for pairwise
keys, but as of currently, the cfg80211 does not allow it.
As validating they cipher parameters for vendor specific cipher suites is the
job of the driver or hardware/firmware, change the cfg80211 to allow also
non-zero pairwise key indexes for vendor specific ciphers.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Tue, 25 Jan 2011 04:32:56 +0000 (23:32 -0500)]
ath5k: remove debug_dump_skb() functions
Now that rx and tx dumps go through the tracing infrastructure,
we no longer need to keep these routines around.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Tue, 25 Jan 2011 04:32:55 +0000 (23:32 -0500)]
ath5k: use tracing for packet tx/rx dump
This adds a few tracepoints to ath5k driver transmit and
receive callbacks in order to record packet traffic.
We record the entire packet in the trace buffer so that
the data can be extracted with trace-cmd and external
plugins.
Compared to the previous debugging calls, this approach
removes an out-of-line function call from the tx and rx
paths in the compiled-in-but-disabled case, while
improving the ability to process the logged data.
A new option, CONFIG_ATH5K_TRACER, is added so that one
may disable the tracepoints completely.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Tue, 25 Jan 2011 04:15:33 +0000 (13:15 +0900)]
ath: Add function to check if 4.9GHz channels are allowed
This adds a helper function to ath/regd.c which can be asked if 4.9GHz channels
are allowed for a given regulatory domain code. This keeps the knowledge of
regdomains and defines like MKK9_MKKC in one place. I'm passing the regdomain
code instead of the ath_regulatory structure because this needs to be called
quite early in the driver inititalization where ath_regulatory is not available
yet in ath5k.
I'm using MKK9_MKKC only because this is the regdomain in the 802.11j enabled
sample cards we got from our vendor. I found some hints in HAL code that this
is used by Atheros to indicate 4.9GHz channels support and that there might be
other domain codes as well, but as I don't have any documentation I'm just
putting in what I need right now. It can be extended later.
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 24 Jan 2011 20:29:25 +0000 (21:29 +0100)]
ath9k: fix tx queue index confusion in debugfs code
Various places printing tx queue information used various different ways to
get a tx queue index for printing statistics. Most of these ways were wrong.
ATH_TXQ_AC_* cannot be used as an index for sc->tx.txq, because it is only
used internally for queue assignment.
One place used WME_AC_* as a queue index for sc->debug.stats.txstats, however
this array uses the ath9k_hw queue number as well.
Fix all of this by always using the ath9k_hw queue number as an index, and
always looking it up by going through sc->tx.txq_map.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 24 Jan 2011 18:23:15 +0000 (19:23 +0100)]
ath9k: remove the virtual wiphy debugfs interface
It does not make much sense to keep the current virtual wiphy implementation
any longer - it adds significant complexity, has very few users and is still
very experimental. At some point in time, it will be replaced by a proper
implementation in mac80211.
By making the code easier to read and maintain, removing virtual wiphy support
helps with fixing the remaining driver issues and adding further improvements.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 24 Jan 2011 18:23:14 +0000 (19:23 +0100)]
ath9k: clean up the code that wakes the mac80211 queues
Instead of spreading ath_wake_mac80211_queue() calls over multiple places
in the tx path that process the tx queue for completion, call it only
where the pending frames counter gets decremented, eliminating some
redundant checks.
To prevent queue draining from waking the queues prematurely (e.g. during
a hardware reset), reset the queue stop state when draining all queues,
as the caller in main.c will run ieee80211_wake_queues(hw) anyway.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: Fix power save usage count imbalance on deinit
While unloading the driver, the ps_usecount is incremented
before configuring gpio registers in deinit_device.
But it is failed to restore the ps_usecount after that.
The problem is that the chip is forcibly moved to FULL SLEEP
by radio_disable when mac80211 is reporting as idle
though ps_usecount is not zero.
This patch retores ps_usecount properly and ensures that
the chip is always moved to full sleep only if ps usage
count is zero which also helps in debugging deadbeef on
multivif case. And also fixes the following warning.
ath: DMA failed to stop in 10 ms AR_CR=0xdeadbeef AR_DIAG_SW=0xdeadbeef
ath: Could not stop RX, we could be confusing the DMA engine when we
start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:536
ath_stoprecv+0xf4/0x100 [ath9k]()
Cc: stable@kernel.org Cc: Paul Stewart <pstew@google.com> Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw: Fix system hang when resuming from S3/S4
The bit 6 & 7 of AR_WA (0x4004) should be enabled only
for the chips that are supporting L0s functionality
while resuming back from S3/S4.
Enabling these bits for AR9280 is causing system hang
within a few S3/S4-resume cycles.
Cc: stable@kernel.org Cc: Jack Lee <jlee@atheros.com> Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Disable interrupts, kill tasklets
and then works in correct order.
Cc: stable@kernel.org Tested-by: Sujith <m.sujith@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Moreover we enable interrupts
in tasklet function, so we could potentially end with interrupts
enabled when driver is not ready to receive them.
I think patch should fix Ben's kernel crash from:
http://marc.info/?l=linux-wireless&m=129438358921501&w=2
Cc: stable@kernel.org Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Tue, 25 Jan 2011 04:31:44 +0000 (23:31 -0500)]
ath5k: correct endianness of frame duration
The ath5k version of ieee80211_generic_frame_duration() returns
an __le16 for standard modes but a cpu-endian int for turbo/half/
quarter rates. Make it always return cpu-endian values.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Tue, 25 Jan 2011 04:31:43 +0000 (23:31 -0500)]
ath5k: fix error handling in ath5k_hw_dma_stop
Review spotted a problem with the error handling in ath5k_hw_dma_stop:
a successful return from ath5k_hw_stop_tx_dma will be treated as
an error, so we always bail out of the loop after processing a single
active queue. As a result, we may not actually stop some queues during
reset.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chaoming Li [Fri, 21 Jan 2011 19:57:37 +0000 (13:57 -0600)]
rtlwifi: Fix firmware upload errors
When the source code from Realtek was prepared for kernel inclusion,
some routines were refactored to reduce the level of indentation. This
patch repairs errors introduced in that process.
Signed-off-by: Chaoming Li <chaoming_li@realsil.com.cn> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 24 Jan 2011 18:11:54 +0000 (19:11 +0100)]
ath9k: fix misplaced debug code
The commit 'ath9k: Add more information to debugfs xmit file.' added more
debug counters to ath9k and also added some lines of code to ath9k_hw.
Since ath9k_hw is also used by ath9k_htc, its code must not depend on ath9k
data structures. In this case it was not fatal, but it's still wrong, so
the code needs to be moved back to ath9k.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
carl9170: utilize fw seq counter for mgmt/non-QoS data frames
"mac80211 will properly assign sequence numbers to QoS-data
frames but cannot do so correctly for non-QoS-data and
management frames because beacons need them from that counter
as well and mac80211 cannot guarantee proper sequencing."
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 26 Jan 2011 08:22:15 +0000 (09:22 +0100)]
mac80211: use DECLARE_EVENT_CLASS
For events that include only the local struct as
their parameter, we can use DECLARE_EVENT_CLASS
and save quite some binary size across segments
as well lines of code.
text data bss dec hex filename
375745 19296 916 395957 60ab5 mac80211.ko.before
367473 17888 916 386277 5e4e5 mac80211.ko.after
-8272 -1408 0 -9680 -25d0 delta
Some more tracepoints with identical arguments
could be combined like this but for now this is
the one that benefits most.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Wed, 19 Jan 2011 09:20:52 +0000 (18:20 +0900)]
ath5k: ath5k_setup_channels cleanup and whitespace
Remove useless test_bit - it's not going to happen because of the way this
function is called only when that bit is set.
And fix some whitespace.
Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw: read and backup AR_WA register value even before chip reset on.
We need to read and backup AR_WA register value permanently and reading
this after the chip is awakened results in this register being zeroed out.
This seems to fix the ASPM with L1 enabled issue that we have observed.
The laptop becomes very slow and hangs mostly with ASPM L1 enabled without
this fix.
Cc: Stable Kernel <stable@kernel.org> Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw: Fix incorrect macversion and macrev checks
There are few places where we are checking for macversion and revsions
before RTC is powered ON. However we are reading the macversion and
revisions only after RTC is powered ON and so both macversion and
revisions are actully zero and this leads to incorrect srev checks
Incorrect srev checks can cause registers to be configured wrongly and can
cause unexpected behavior. Fixing this seems to address the ASPM issue that
we have observed. The laptop becomes very slow and hangs mostly with ASPM L1
enabled without this fix.
fix this by reading the macversion and revisisons even before we start
using them. There is no reason why should we delay reading this info
until RTC is powered on as this is just a register information.
Cc: Stable Kernel <stable@kernel.org> Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Tue, 25 Jan 2011 16:38:06 +0000 (08:38 -0800)]
MAINTAINERS: remove Reinette Chatre as iwlwifi maintainer
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 24 Jan 2011 18:28:49 +0000 (19:28 +0100)]
mac80211: fix a crash in ieee80211_beacon_get_tim on change_interface
Some drivers (e.g. ath9k) do not always disable beacons when they're
supposed to. When an interface is changed using the change_interface op,
the mode specific sdata part is in an undefined state and trying to
get a beacon at this point can produce weird crashes.
To fix this, add a check for ieee80211_sdata_running before using
anything from the sdata.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Mon, 24 Jan 2011 06:01:54 +0000 (07:01 +0100)]
wl12xx: Increase scan channel dwell time for passive scans
The passive scan channel dwell time currently used is 30-60TU. A typical
beacon interval for AP's is 100TU. This leads to a ~30% worst-case probability
of finding an AP via passive scanning.
For 5GHz bands for DFS frequencies passive scanning is the only scanning
option. Hence for these, the probability of finding an AP is very low.
To fix this, increase the passive channel scan dwell times (also the early
leave value, as 5GHz channels are still typically very silent.) Use a value
of 100TU, because that covers most typical AP configurations.
Based on testing the probability of finding an AP (100TU beacon interval) on
a single scan round are as follows (based on 100 iterations):
Levi, Shahar [Sun, 23 Jan 2011 06:27:22 +0000 (07:27 +0100)]
wl12xx: BA initiator support
Add 80211n BA initiator session support wl1271 driver.
Include BA supported FW version auto detection mechanism.
BA initiator session management included in FW independently.
Signed-off-by: Shahar Levi <shahar_levi@ti.com> Reviewed-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
Juuso Oikarinen [Fri, 14 Jan 2011 11:48:46 +0000 (12:48 +0100)]
wl12xx: Cleanup PLT mode when module is removed
PLT mode start/stop is controlled from userspace. When removing module, the
PLT mode state is however not checked, and not cleared. There is the possibility
of some unwanted state to left linger and there is even the possiblity of a
kernel crash if for instance IRQ work is running when the module is removed.
Fix this by stopping PLT mode on module removal, if still running.
Luciano Coelho [Wed, 12 Jan 2011 13:27:03 +0000 (14:27 +0100)]
wl12xx: add hw configuration for max supported AMDPU size
The wl12xx chips do the AMDPU aggregation work in the firmware, but it
supports a maximum of 8 frames per block. Configure the mac80211 hw
structure accordingly.
changed the visibility of the debug_level module parameter
in the filesystem to be readable and writable to the root user.
It is now accessible under /sys/module/wl12xx/parameters
removed the debug_level debugfs file that was created under
/sys/kernel/debug/...
Signed-off-by: Guy Eilam <guy@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
Luciano Coelho [Tue, 11 Jan 2011 17:25:18 +0000 (18:25 +0100)]
wl12xx: don't modify the global supported band structures
When 11a is not supported, we were modifying the global structure that
contains the bands supported by the driver. This causes problems when
having more one wl12xx device in the same system because they all use
the same global. This also causes problems when the wl12xx_sdio
module is removed and the wl12xx module remains.
Fix this problem by copying the band structure into the wl12xx
instance.
Eliad Peller [Sun, 26 Dec 2010 08:27:50 +0000 (09:27 +0100)]
wl12xx: don't join upon disassociation
wl12xx "rejoins" upon every BSS_CHANGED_BSSID notification.
However, there is no need to rejoin after disassociation, so just
filter out the case when the new bssid is 00:00:00:00:00:00.
Arik Nemtsov [Sat, 16 Oct 2010 19:44:57 +0000 (21:44 +0200)]
wl12xx: AP mode - fetch appropriate firmware for AP
AP and STA modes use different firmwares.
Differentiate the firmware files by name and fetch the appropriate one
when add_interface is called by mac80211. The STA firmware is chosen for
PLT mode.
Arik Nemtsov [Sat, 16 Oct 2010 16:19:53 +0000 (18:19 +0200)]
wl12xx: AP mode - init sequence
Split HW init sequence into AP/STA specific parts
The AP specific init sequence includes configuration of templates, rate
classes, power mode, etc. Also unmask AP specific events in the event mbox.
Separate the differences between AP and STA init into mode
specific functions called from wl1271_hw_init. The first is called after
radio configuration and the second after memory configuration.
Arik Nemtsov [Fri, 12 Nov 2010 15:15:03 +0000 (17:15 +0200)]
wl12xx: AP mode - workaround for FW bug on station remove
Sometimes an event indicating station removal is not sent up by
firmware. We work around this by always indicating success in when
a wait for the event timeouts.
Temporary workaround until a FW fix is introduced.
Arik Nemtsov [Sat, 16 Oct 2010 16:08:58 +0000 (18:08 +0200)]
wl12xx: AP-mode high level commands
Add commands to start/stop BSS, add/remove STA and configure encryption
keys. Split the encryption commands "set key" and "set default key" into
AP and STA specific versions.
Eliad Peller [Wed, 22 Dec 2010 11:38:52 +0000 (12:38 +0100)]
wl12xx: fix some sparse warnings
Note that wl1271_write32() calls cpu_to_le32() by itself, so calling
wl1271_write32(addr, cpu_to_le32(val)) is in fact a bug on BE systems.
Fix the following sparse warnings:
drivers/net/wireless/wl12xx/cmd.c:662:16: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/cmd.c:662:16: expected unsigned short [unsigned] [addressable] [usertype] llc_type
drivers/net/wireless/wl12xx/cmd.c:662:16: got restricted __be16 [usertype] <noident>
drivers/net/wireless/wl12xx/cmd.c:674:17: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/cmd.c:674:17: expected unsigned int [unsigned] [addressable] [usertype] sender_ip
drivers/net/wireless/wl12xx/cmd.c:674:17: got restricted __be32 [usertype] ip_addr
drivers/net/wireless/wl12xx/rx.c:202:4: warning: incorrect type in argument 3 (different base types)
drivers/net/wireless/wl12xx/rx.c:202:4: expected unsigned int [unsigned] [usertype] val
drivers/net/wireless/wl12xx/rx.c:202:4: got restricted __le32 [usertype] <noident>
drivers/net/wireless/wl12xx/acx.c:1247:23: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/acx.c:1247:23: expected restricted __le32 [usertype] ht_capabilites
drivers/net/wireless/wl12xx/acx.c:1247:23: got unsigned long
drivers/net/wireless/wl12xx/acx.c:1250:24: warning: invalid assignment: |=
drivers/net/wireless/wl12xx/acx.c:1250:24: left side has type restricted __le32
drivers/net/wireless/wl12xx/acx.c:1250:24: right side has type unsigned long
drivers/net/wireless/wl12xx/acx.c:1253:24: warning: invalid assignment: |=
drivers/net/wireless/wl12xx/acx.c:1253:24: left side has type restricted __le32
drivers/net/wireless/wl12xx/acx.c:1253:24: right side has type unsigned long
drivers/net/wireless/wl12xx/acx.c:1256:24: warning: invalid assignment: |=
drivers/net/wireless/wl12xx/acx.c:1256:24: left side has type restricted __le32
drivers/net/wireless/wl12xx/acx.c:1256:24: right side has type unsigned long
Upon rmmod, the <debugfs>/ieee80211/phyX dir is being removed.
later, we try to remove <debugfs>/ieee80211/phyX/wl12xx, which
might result in NULL dereference.
Remove the excessive debugfs_remove_recursive() call.
(consequently, there is no more need to save wl->rootdir)
Wey-Yi Guy [Fri, 14 Jan 2011 01:09:29 +0000 (17:09 -0800)]
iwlwifi: initial P2P support
If PAN functionality is present, advertise
P2P interface type support and thus support
for P2P. However, the support is currently
somewhat incomplete -- NoA schedule isn't
added to probe responses, and 11b bitrates
may be used still, etc. Therefore, make it
all optional with a Kconfig option.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Thu, 6 Jan 2011 16:07:10 +0000 (08:07 -0800)]
iwlwifi: implement remain-on-channel
For device supporting PAN/P2P, use the PAN
context to implement the remain-on-channel
operation using device offloads so that the
filters in the device will be programmed
correctly -- otherwise we cannot receive
any probe request frames during off-channel
periods.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
projects / linux-beck.git / log