Shobhit Kumar [Wed, 11 Dec 2013 12:22:05 +0000 (17:52 +0530)]
drm/i915: Reorganize the DSI enable/disable sequence
Basically ULPS handling during enable/disable has been moved to
pre_enable and post_disable phases. PLL and panel power disable
also has been moved to post_disable phase. The ULPS entry/exit
sequneces as suggested by HW team is as follows -
During enable time -
set DEVICE_READY --> Clear DEVICE_READY --> set DEVICE_READY
And during disable time to flush all FIFOs -
set ENTER_SLEEP --> EXIT_SLEEP --> ENTER_SLEEP
Also during disbale sequnece sub-encoder disable is moved to the end
after port is disabled.
v2: Based on comments from Ville
- Detailed epxlaination in the commit messgae
- Moved parameter changes out into another patch
- Backlight enabling will be a new patch
v3: Updated as per Jani's comments
- Removed the I915_WRITE_BITS as it is not needed
- Moved panel_reset and send_otp_cmds hooks to dsi_pre_enable
- Moved disable_panel_power hook to dsi_post_disable
- Replace hardcoding with AFE_LATCHOUT
v4: Make intel_dsi_device_ready and intel_dsi_clear_device_ready static
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohan.marimuthu@intel.com> Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Shobhit Kumar [Tue, 10 Dec 2013 06:44:57 +0000 (12:14 +0530)]
drm/i915: Try harder to get best m, n, p values with minimal error
Basically check for both +ive and -ive deviation from target clock and
pick the one with minimal error. If we get a direct match, break from
loop to acheive some optimization.
v2: Use signed variable for target and calculated dsi clock values
Signed-off-by: Vijayakumar Balakrishnan <vijayakumar.balakrishnan@intel.com> Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Shobhit Kumar [Tue, 10 Dec 2013 06:44:56 +0000 (12:14 +0530)]
drm/i915: Compute dsi_clk from pixel clock
Pixel clock based calculation is recommended in the MIPI host controller
documentation
v2: Based on review comments from Jani and Ville
- Use dsi_clk in KHz rather than converting in Hz and back to MHz
- RR formula is retained though not used but return dsi_clk in KHz now
- Moved the m-n-p changes into a separate patch
- Removed the parameter check for intel_dsi->dsi_clock_freq. This will be
bought back in if needed when appropriate panel drivers are done
v3: Removed the unused mnp calculation from static table
Signed-off-by: Vijayakumar Balakrishnan <vijayakumar.balakrishnan@intel.com> Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 9 Dec 2013 16:54:17 +0000 (18:54 +0200)]
drm/i915: Decrease gen2 vco frequency minimum to 908 MHz
On my 855 machine the BIOS uses the following DPLL settings:
DPLL 0x90016000
FP0 = 0x61207
FP1 = 0x21207
With the 66MHz SSC refclock, that puts the BIOS generated VCO
frequency at ~908 MHz, which is lower than the 930 MHz limit
we have currently. This also results in the pixel clock coming
out significantly higher than the requested 65 MHz when we try
to recompute it.
Reduce the the VCO limit to 908 MHz. Combined with the earlier
SSC reference clock accuracy fix, this results in the pixel clock
coming out as 65.08 MHz which is quite close to the target. For
some reason the BIOS uses 64.881 MHz, which isn't quite as close.
This makes kms_flip wf_vblank-ts-check pass for the first time
on this machine \o/
Cc: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 9 Dec 2013 16:54:16 +0000 (18:54 +0200)]
drm/i915: Fix 66 MHz LVDS SSC freq for gen2
Store the SSC refclock frequency in kHz to get more accuracy. Currently
we're pretending that 66 MHz is ~66000 kHz, when in fact it is actually
~66667 kHz. By storing the less rounded kHz value we get a much better
accuracy for out pixel clock calculations.
Cc: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 9 Dec 2013 16:54:15 +0000 (18:54 +0200)]
drm/i915: Increase gen2 vco frequency limit to 1512 MHz
Bruno Prémont has a 855 machine with a 1400x1050 LVDS screen.
The VBT mode is as follows:
0:"1400x1050" 0 108000 1400 1416 1528 1688 1050 1051 1054 1066 0x8 0xa
The BIOS uses the following DPLL settings:
DPLL = 0x90020000
FP0 = 0x2140e
FP1 = 0x21207
That puts the BIOS generated VCO frequency at 1512 MHz, which is
higher than the 1400 MHz limit we have currently.
Let's bump the VCO limit to 1512 MHz and see what happens.
Cc: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 9 Dec 2013 16:54:14 +0000 (18:54 +0200)]
drm/i915: Change N divider minimum from 3 to 2 for gen2
Bruno Prémont has a 855 machine with a 1400x1050 LVDS screen.
The VBT mode is as follows:
0:"1400x1050" 0 108000 1400 1416 1528 1688 1050 1051 1054 1066 0x8 0xa
The BIOS uses the following DPLL settings:
DPLL = 0x90020000
FP0 = 0x2140e
FP1 = 0x21207
We can't generate that pixel clock currently as we're limiting the N
divider to at least 3, whereas the BIOS uses a value of 2.
Let's reduce the N minimum to 2 and see what happens.
Cc: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 9 Dec 2013 16:54:13 +0000 (18:54 +0200)]
drm/i915: Extract p2 divider correctly for gen2 LVDS dual channel
In order to determine the correct p2 divider for LVDS on gen2,
we need to check the CLKB mode from the LVDS port register to
determine if we're dealing with single or dual channel LVDS.
Cc: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 10 Dec 2013 19:44:43 +0000 (21:44 +0200)]
drm/i915: Record BB_ADDR for every ring
Every ring seems to have a BB_ADDR registers, so include them all in the
error state.
v2: Also include the _UDW on BDW
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 10 Dec 2013 18:47:44 +0000 (20:47 +0200)]
drm/i915: Use 32bit read for BB_ADDR
The BB_ADDR register is documented to be 32bits at least since SNB.
Prior to that the high 32bits were listed as MBZ, so using a 64bit read
doesn't seem worth anything. Also the simulator doesn't like the 64bit
read. So just switch to using a 32bit read instead.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 6 Dec 2013 19:32:42 +0000 (17:32 -0200)]
drm/i915: fix VDD override off wait
If we're disabling the VDD override bit and the panel is enabled, we
don't need to wait for anything. If the panel is disabled, then we
need to actually wait for panel_power_cycle_delay, not
panel_power_down_delay, because the power down delay was already
respected when we disabled the panel.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 6 Dec 2013 19:32:41 +0000 (17:32 -0200)]
drm/i915: don't touch the VDD when disabling the panel
I don't see a reason to touch VDD when we're disabling the panel:
since the panel is enabled, we don't need VDD. This saves a few sleep
calls from the vdd_on and vdd_off functions at every modeset.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69693 Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix the patch mangle wiggle has done ... Spotted by Paulo.
Also drop the runtime_pm_put call which now has to go due to different
patch ordering. Also from Paul.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 21 Nov 2013 15:47:28 +0000 (13:47 -0200)]
drm/i915: add runtime PM support on Haswell
The code to enable/disable PC8 already takes care of saving and
restoring all the registers we need to save/restore, so do a put()
call when we enable PC8 and a get() call when we disable it.
Ideally, in order to make it easier to add runtime PM support to other
platforms, we should move some things from the PC8 code to the runtime
PM code, but let's do this later, since we can make Haswell work right
now.
V2: - Rebase
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Don't actually enable runtime pm since I didn't merge all
patches.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 21 Nov 2013 15:47:25 +0000 (13:47 -0200)]
drm/i915: disable interrupts when enabling PC8
The plan is to merge PC8 and D3 into a single feature, and when we're
in D3 we won't get any hotplug interrupt anyway, so leaving them
enable doesn't make sense, and it also brings us a problem. The
problem is that we get a hotplug interrupt right when we we wake up
from D3, when we're still waking up everything. If we fully disable
interrupts we won't get this hotplug interrupt, so we won't have
problems.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 21 Nov 2013 15:47:24 +0000 (13:47 -0200)]
drm/i915: do not assert DE_PCH_EVENT_IVB enabled
The current code was checking if all bits of "val" were enabled and
DE_PCH_EVENT_IVB was disabled. The new code doesn't care about the
state of DE_PCH_EVENT_IVB: it just checks if everything else is 1.
The goal is that future patches may completely disable interrupts, and
the LCPLL-disabling code shouldn't care about the state of
DE_PCH_EVENT_IVB.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: I think the commit message is actually wrong in it's
description of what the old test checked, but the new one seems sane.
So meh.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 21 Nov 2013 15:47:23 +0000 (13:47 -0200)]
drm/i915: get a runtime PM reference when the panel VDD is on
And put it when it's off. Otherwise, when you run pm_pc8 from
intel-gpu-tools, and the delayed function that disables VDD runs,
we'll get some messages saying we're touching registers while the HW
is suspended.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Wed, 27 Nov 2013 20:20:34 +0000 (18:20 -0200)]
drm/i915: add runtime put/get calls at the basic places
If I add code to enable runtime PM on my Haswell machine, start a
desktop environment, then enable runtime PM, these functions will
complain that they're trying to read/write registers while the
graphics card is suspended.
v2: - Simplify i915_gem_fault changes.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Drop the hunk in i915_hangcheck_elapsed, it's the wrong thing
to do.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 6 Dec 2013 22:34:21 +0000 (20:34 -0200)]
drm/i915: do adapter power state notification at runtime PM
Now that we are actually setting the device to the D3 state, we should
issue the notification.
The opregion spec says we should send the message before the adapter
is about to be placed in a lower power state, and after the adapter is
placed in a higher power state.
Jani originally wrote a similar patch for PC8, but then we discovered
that we were not really changing the PCI D states when
enabling/disabling PC8, so we had to postpone his patch.
v2: - Improve commit message, explaining the expected state.
v3: - Rebase.
Cc: Jani Nikula <jani.nikula@intel.com> Credits-to: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> (v2) Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 6 Dec 2013 22:32:13 +0000 (20:32 -0200)]
drm/i915: add initial Runtime PM functions
This patch adds the initial infrastructure to allow a Runtime PM
implementation that sets the device to its D3 state. The patch just
adds the necessary callbacks and the initial infrastructure.
We still don't have any platform that actually uses this
infrastructure, we still don't call get/put in all the places we need
to, and we don't have any function to save/restore the state of the
registers. This is not a problem since no platform uses the code added
by this patch. We have a few people simultaneously working on runtime
PM, so this initial code could help everybody make their plans.
V2: - Move some functions to intel_pm.c
- Remove useless pm_runtime_allow() call at init
- Remove useless pm_runtime_mark_last_busy() call at get
- Use pm_runtime_get_sync() instead of 2 calls
- Add a WARN to check if we're really awake
V3: - Rebase.
V4: - Don't need to call pci_{save,restore}_state and
pci_set_power_sate, since they're already called by the PCI
layer
- Remove wrong pm_runtime_enable() call at init_runtime_pm
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Wed, 27 Nov 2013 19:59:22 +0000 (17:59 -0200)]
drm/i915: get a PC8 reference when enabling the power well
In the current code, at haswell_modeset_global_resources, first we
decide if we want to enable/disable the power well, then we decide if
we want to enable/disable PC8. On the case where we're enabling PC8
this works fine, but on the case where we disable PC8 due to a non-eDP
monitor being enabled, we first enable the power well and then disable
PC8. Although wrong, this doesn't seem to be causing any problems now,
and we don't even see anything in dmesg. But the patches for runtime
D3 turn this problem into a real bug, so we need to fix it.
This fixes the "modeset-non-lpsp" subtest from the "pm_pc8" test from
intel-gpu-tools.
v2: - Rebase (i915_disable_power_well).
v3: - More reabase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 10 Dec 2013 13:19:08 +0000 (15:19 +0200)]
drm/i915: Don't cast away const from infoframe buffer
We don't modify the packed infoframe data, so we should keep the
const qualifier in place. Just pass the buffer as 'const void *'
instead of 'const uint8_t *' and we can drop the cast entirely.
v2: Do intel_sdvo_write_infoframe() as well
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Vandana Kannan [Tue, 10 Dec 2013 08:07:36 +0000 (13:37 +0530)]
drm/i915: Make downclock deduction common for all panels
If one mode of a internal panel has more than one refresh rate, then a reduced
clock is found for the LFP (LVDS/eDP). This enables switching between low
and high frequency dynamically. Moving downclock calculation to intel_panel
so that it is common for LVDS and eDP.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since early sanitize and uncore sanitize are called one after the other,
I think, we can remove second forcewake reset which was are calling
twice in both the functions.
Daniel Vetter [Mon, 9 Dec 2013 08:17:02 +0000 (09:17 +0100)]
Merge tag 'v3.13-rc3' into drm-intel-next-queued
Linux 3.13-rc3
I need a backmerge for two reasons:
- For merging the ppgtt patches from Ben I need to pull in the bdw
support.
- We now have duplicated calls to intel_uncore_forcewake_reset in the
setup code to due 2 different patches merged into -next and 3.13.
The conflict is silen so I need the merge to be able to apply
Deepak's fixup patch.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Trivial conflict, it doesn't even show up in the merge diff.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 6 Dec 2013 22:29:01 +0000 (20:29 -0200)]
drm/i915: change CRTC assertion on LCPLL disable
Currently, PC8 is enabled at modeset_global_resources, which is called
after intel_modeset_update_state. Due to this, there's a small race
condition on the case where we start enabling PC8, then do a modeset
while PC8 is still being enabled. The racing condition triggers a WARN
because intel_modeset_update_state will mark the CRTC as enabled, then
the thread that's still enabling PC8 might look at the data structure
and think that PC8 is being enabled while a pipe is enabled. Despite
the WARN, this is not really a bug since we'll wait for the
PC8-enabling thread to finish when we call modeset_global_resources.
The spec says the CRTC cannot be enabled when we disable LCPLL, so we
had a check for crtc->base.enabled. If we change to crtc->active we
will still prevent disabling LCPLL while the CRTC is enabled, and we
will also prevent the WARN above.
This is a replacement for the previous patch named
"drm/i915: get/put PC8 when we get/put a CRTC"
Testcase: igt/pm_pc8/modeset-lpsp-stress-no-wait Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Linus Torvalds [Fri, 6 Dec 2013 16:34:16 +0000 (08:34 -0800)]
Merge tag 'trace-fixes-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"A regression showed up that there's a large delay when enabling all
events. This was prevalent when FTRACE_SELFTEST was enabled which
enables all events several times, and caused the system bootup to
pause for over a minute.
This was tracked down to an addition of a synchronize_sched()
performed when system call tracepoints are unregistered.
The synchronize_sched() is needed between the unregistering of the
system call tracepoint and a deletion of a tracing instance buffer.
But placing the synchronize_sched() in the unreg of *every* system
call tracepoint is a bit overboard. A single synchronize_sched()
before the deletion of the instance is sufficient"
* tag 'trace-fixes-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Only run synchronize_sched() at instance deletion time
Linus Torvalds [Fri, 6 Dec 2013 16:30:18 +0000 (08:30 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of nine fixes (and one author update).
The libsas one should fix discovery in eSATA devices, the WRITE_SAME
one is the largest, but it should fix a lot of problems we've been
getting with the emulated RAID devices (they've been effectively lying
about support and then firmware has been choking on the commands).
The rest are various crash, hang or warn driver fixes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] bfa: Fix crash when symb name set for offline vport
[SCSI] enclosure: fix WARN_ON in dual path device removing
[SCSI] pm80xx: Tasklets synchronization fix.
[SCSI] pm80xx: Resetting the phy state.
[SCSI] pm80xx: Fix for direct attached device.
[SCSI] pm80xx: Module author addition
[SCSI] hpsa: return 0 from driver probe function on success, not 1
[SCSI] hpsa: do not discard scsi status on aborted commands
[SCSI] Disable WRITE SAME for RAID and virtual host adapter drivers
[SCSI] libsas: fix usage of ata_tf_to_fis
Linus Torvalds [Fri, 6 Dec 2013 16:28:35 +0000 (08:28 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull IMA fixes from James Morris:
"Here are two more fixes for IMA"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
ima: properly free ima_template_entry structures
ima: Do not free 'entry' before it is initialized
Linus Torvalds [Fri, 6 Dec 2013 16:27:47 +0000 (08:27 -0800)]
Merge tag 'dt-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Various DT binding documentation updates
- Add Kumar Gala and remove Stephen Warren as DT binding maintainers
* tag 'dt-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt: binding: reword PowerPC 8xxx GPIO documentation
ARM: tegra: delete nvidia,tegra20-spi.txt binding
hwmon: ntc_thermistor: Fix typo (pullup-uV -> pullup-uv)
of: add vendor prefix for GMT
clk: exynos: Fix typos in DT bindings documentation
of: Add vendor prefix for LG Corporation
Documentation: net: fsl-fec.txt: Add phy-supply entry
ARM: dts: doc: Document missing binding for omap5-mpu
dt-bindings: add ARMv8 PMU binding
MAINTAINERS: remove swarren from DT bindings
MAINTAINERS: Add Kumar to Device Tree Binding maintainers group
Gu Zheng [Wed, 4 Dec 2013 10:19:06 +0000 (18:19 +0800)]
aio: clean up aio ring in the fail path
Clean up the aio ring file in the fail path of aio_setup_ring
and ioctx_alloc. And maybe it can fix the GPF issue reported by
Dave Jones:
https://lkml.org/lkml/2013/11/25/898
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com> Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Linus Torvalds [Fri, 6 Dec 2013 02:26:40 +0000 (18:26 -0800)]
Merge tag 'pm-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
- cpufreq regression fix from Bjørn Mork restoring the pre-3.12
behavior of the framework during system suspend/hibernation to avoid
garbage sysfs files from being left behind in case of a suspend error
- PNP regression fix to restore the correct states of devices after
resume from hibernation broken in 3.12. From Dmitry Torokhov.
- cpuidle fix to prevent cpuidle device unregistration from crashing
due to a NULL pointer dereference if cpuidle has been disabled from
the kernel command line. From Konrad Rzeszutek Wilk.
- intel_idle fix for the C6 state definition on Intel Avoton/Rangeley
processors from Arne Bockholdt.
- Power capping framework fix to make the energy_uj sysfs attribute
work in accordance with the documentation. From Srinivas Pandruvada.
- epoll fix to make it ignore the EPOLLWAKEUP flag if the kernel has
been compiled with CONFIG_PM_SLEEP unset (in which case that flag
should not have any effect). From Amit Pundir.
- cpufreq fix to prevent governor sysfs files from being lost over
system suspend/resume in some (arguably unusual) situations. From
Viresh Kumar.
* tag 'pm-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PowerCap: Fix mode for energy counter
PNP: fix restoring devices after hibernation
cpuidle: Check for dev before deregistering it.
epoll: drop EPOLLWAKEUP if PM_SLEEP is disabled
cpufreq: fix garbage kobjects on errors during suspend/resume
cpufreq: suspend governors on system suspend/hibernate
intel_idle: Fixed C6 state on Avoton/Rangeley processors
Linus Torvalds [Thu, 5 Dec 2013 23:33:27 +0000 (15:33 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block layer fixes from Jens Axboe:
"A small collection of fixes for the current series. It contains:
- A fix for a use-after-free of a request in blk-mq. From Ming Lei
- A fix for a blk-mq bug that could attempt to dereference a NULL rq
if allocation failed
- Two xen-blkfront small fixes
- Cleanup of submit_bio_wait() type uses in the kernel, unifying
that. From Kent
- A fix for 32-bit blkg_rwstat reading. I apologize for this one
looking mangled in the shortlog, it's entirely my fault for missing
an empty line between the description and body of the text"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: fix use-after-free of request
blk-mq: fix dereference of rq->mq_ctx if allocation fails
block: xen-blkfront: Fix possible NULL ptr dereference
xen-blkfront: Silence pfn maybe-uninitialized warning
block: submit_bio_wait() conversions
Update of blkg_stat and blkg_rwstat may happen in bh context
Linus Torvalds [Thu, 5 Dec 2013 21:05:48 +0000 (13:05 -0800)]
Merge tag 'nfs-for-3.13-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Stable fix for a NFSv4.1 delegation and state recovery deadlock
- Stable fix for a loop on irrecoverable errors when returning
delegations
- Fix a 3-way deadlock between layoutreturn, open, and state recovery
- Update the MAINTAINERS file with contact information for Trond
Myklebust
- Close needs to handle NFS4ERR_ADMIN_REVOKED
- Enabling v4.2 should not recompile nfsd and lockd
- Fix a couple of compile warnings
* tag 'nfs-for-3.13-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
nfs: fix do_div() warning by instead using sector_div()
MAINTAINERS: Update contact information for Trond Myklebust
NFSv4.1: Prevent a 3-way deadlock between layoutreturn, open and state recovery
SUNRPC: do not fail gss proc NULL calls with EACCES
NFSv4: close needs to handle NFS4ERR_ADMIN_REVOKED
NFSv4: Update list of irrecoverable errors on DELEGRETURN
NFSv4 wait on recovery for async session errors
NFS: Fix a warning in nfs_setsecurity
NFS: Enabling v4.2 should not recompile nfsd and lockd
Tony Lu [Thu, 5 Dec 2013 20:36:54 +0000 (15:36 -0500)]
ftrace: default to tilegx if ARCH=tile is specified
This matches the existing behavior in arch/tile/Makefile for defconfig.
Reported-by: fengguang.wu@intel.com Acked-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Tony Lu <zlu@tilera.com> Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Steven Rostedt [Tue, 3 Dec 2013 17:41:20 +0000 (12:41 -0500)]
tracing: Only run synchronize_sched() at instance deletion time
It has been reported that boot up with FTRACE_SELFTEST enabled can take a
very long time. There can be stalls of over a minute.
This was tracked down to the synchronize_sched() called when a system call
event is disabled. As the self tests enable and disable thousands of events,
this makes the synchronize_sched() get called thousands of times.
The synchornize_sched() was added with d562aff93bfb53 "tracing: Add support
for SOFT_DISABLE to syscall events" which caused this regression (added
in 3.13-rc1).
The synchronize_sched() is to protect against the events being accessed
when a tracer instance is being deleted. When an instance is being deleted
all the events associated to it are unregistered. The synchronize_sched()
makes sure that no more users are running when it finishes.
Instead of calling synchronize_sched() for all syscall events, we only
need to call it once, after the events are unregistered and before the
instance is deleted. The event_mutex is held during this action to
prevent new users from enabling events.
Link: http://lkml.kernel.org/r/20131203124120.427b9661@gandalf.local.home Reported-by: Petr Mladek <pmladek@suse.cz> Acked-by: Tom Zanussi <tom.zanussi@linux.intel.com> Acked-by: Petr Mladek <pmladek@suse.cz> Tested-by: Petr Mladek <pmladek@suse.cz> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Linus Torvalds [Thu, 5 Dec 2013 17:55:20 +0000 (09:55 -0800)]
Merge tag 'fbdev-fixes-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull minor fbdev fixes from Tomi Valkeinen.
* tag 'fbdev-fixes-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
video: vt8500: fix error handling in probe()
atmel_lcdfb: fix module autoload
fbdev: sh_mobile_meram: Fix defined but not used compiler warnings
video: kyro: fix incorrect sizes when copying to userspace
ARM: OMAPFB: panel-sony-acx565akm: fix bad unlock balance
Linus Torvalds [Thu, 5 Dec 2013 17:54:35 +0000 (09:54 -0800)]
Merge tag 'sound-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A usual pattern of half ASoC and half HD-audio fixes, although
HD-audio fixups have more volumes, in addition to a couple of trivial
fixes. Nothing to worry much is found here.
For ASoC side: a few fixes for PCM rate constraints calculations,
regmap byte-order fix, the rest driver specific fixes (atmel, fsl,
omap, kirkwood, wm codecs).
For HD-audio: Dell headset and mono out fix, ELD update in polling
mode, ALC283 Chromebook fixes, a few fixes for old AD codecs and
MBA2, one regression fix"
* tag 'sound-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (30 commits)
ALSA: hda - Fix silent output on MacBook Air 2,1
ALSA: hda - Fix missing ELD info when using jackpoll_ms parameter
ALSA: hda/realtek - remove hp_automute_hook from alc283_fixup_chromebook
ASoC: wm8731: fix dsp mode configuration
ALSA: hda/realtek - Independent of model for HP
ALSA: hda - Fix headset mic input after muted internal mic (Dell/Realtek)
ALSA: hda - Use always amps for auto-mute on AD1986A codec
ALSA: hda/analog - Handle inverted EAPD properly in vmaster hook
ALSA: hda - Another fixup for ASUS laptop with ALC660 codec
ALSA: atmel: Fix possible array overflow
ALSA: hda - Fix complete_all() timing in deferred probes
ALSA: hda - Fix bad EAPD setup for HP machines with AD1984A
ASoC: core: fix devres parameter in devm_snd_soc_register_card()
ASoC: omap: n810: Convert to clk_prepare_enable/clk_disable_unprepare
ASoC: fsl: set correct platform drvdata in pcm030_fabric_probe()
ASoC: fsl: imx-pcm-fiq: Remove unused 'runtime' variable
ASoC: fsl: imx-pcm-fiq: remove bogus period delta calculation
ALSA: hda - Fix silent output on ASUS W7J laptop
ASoC: core: Use consistent byte ordering in snd_soc_bytes_get
ALSA: dice: fix array limits in dice_proc_read()
...
Chris Wilson [Mon, 2 Dec 2013 13:26:07 +0000 (11:26 -0200)]
drm/i915: Do hw quiescing first during unload
If we force the hw to idle as our first step during unload, we can abort
the unload upon failure. Later we can probe whether the hardware remain
active even after we try to shut it down.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Linus Torvalds [Thu, 5 Dec 2013 05:45:21 +0000 (21:45 -0800)]
Merge branch 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 and EFI fixes from Peter Anvin:
"Half of these are EFI-related:
The by far biggest change is the change to hold off the deletion of a
sysfs entry while a backend scan is in progress. This is to avoid
calling kmemdup() while under a spinlock.
The other major change is for each entry in the EFI pstore backend to
get a unique identifier, as required by the pstore filesystem proper.
The other changes are:
A fix to the recent consolidation and optimization of using "asm goto"
with read-modify-write operation, which broke the bitops; specifically
in such a way that we could end up generating invalid code.
A build hack to make sure we compile with -mno-sse. icc, and most
likely future versions of gcc, can generate SSE instructions unless we
tell it not to.
A comment-only patch to a change the was due in part to an unpublished
erratum; now when the erratum is published we want to add a comment
explaining why"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic, doc: Justification for disabling IO APIC before Local APIC
x86, bitops: Correct the assembly constraints to testing bitops
x86-64, build: Always pass in -mno-sse
efi-pstore: Make efi-pstore return a unique id
x86/efi: Fix earlyprintk off-by-one bug
efivars, efi-pstore: Hold off deletion of sysfs entry until the scan is completed
Fenghua Yu [Thu, 5 Dec 2013 00:07:49 +0000 (16:07 -0800)]
x86/apic, doc: Justification for disabling IO APIC before Local APIC
Since erratum AVR31 in "Intel Atom Processor C2000 Product Family
Specification Update" is now published, I added a justification
comment for disabling IO APIC before Local APIC, as changed in commit:
522e66464467 x86/apic: Disable I/O APIC before shutdown of the local APIC
As per the documentation of powercap sysfs, energy_uj field is read only,
if it can't be reset. Currently it always allows write but will fail,
if there is no reset callback.
Changing mode field, to read only if there is no reset callback.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Reported-by: Dirk Brandewie <dirk.j.brandewie@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
H. Peter Anvin [Wed, 4 Dec 2013 22:31:28 +0000 (14:31 -0800)]
x86, bitops: Correct the assembly constraints to testing bitops
In checkin:
0c44c2d0f459 x86: Use asm goto to implement better modify_and_test() functions
the various functions which do modify and test were unified and
optimized using "asm goto". However, this change missed the detail
that the bitops require an "Ir" constraint rather than an "er"
constraint ("I" = integer constant from 0-31, "e" = signed 32-bit
integer constant). This would cause code to miscompile if these
functions were used on constant bit positions 32-255 and the build to
fail if used on constant bit positions above 255.
Add the constraints as a parameter to the GEN_BINARY_RMWcc() macro to
avoid this problem.
Reported-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/529E8719.4070202@zytor.com
Helge Deller [Mon, 2 Dec 2013 18:59:31 +0000 (19:59 +0100)]
nfs: fix do_div() warning by instead using sector_div()
When compiling a 32bit kernel with CONFIG_LBDAF=n the compiler complains like
shown below. Fix this warning by instead using sector_div() which is provided
by the kernel.h header file.
fs/nfs/blocklayout/extents.c: In function ‘normalize’:
include/asm-generic/div64.h:43:28: warning: comparison of distinct pointer types lacks a cast [enabled by default]
fs/nfs/blocklayout/extents.c:47:13: note: in expansion of macro ‘do_div’
nfs/blocklayout/extents.c:47:2: warning: right shift count >= width of type [enabled by default]
fs/nfs/blocklayout/extents.c:47:2: warning: passing argument 1 of ‘__div64_32’ from incompatible pointer type [enabled by default]
include/asm-generic/div64.h:35:17: note: expected ‘uint64_t *’ but argument is of type ‘sector_t *’
extern uint32_t __div64_32(uint64_t *dividend, uint32_t divisor);
Trond Myklebust [Wed, 4 Dec 2013 17:09:45 +0000 (12:09 -0500)]
NFSv4.1: Prevent a 3-way deadlock between layoutreturn, open and state recovery
Andy Adamson reports:
The state manager is recovering expired state and recovery OPENs are being
processed. If kswapd is pruning inodes at the same time, a deadlock can occur
when kswapd calls evict_inode on an NFSv4.1 inode with a layout, and the
resultant layoutreturn gets an error that the state mangager is to handle,
causing the layoutreturn to wait on the (NFS client) cl_rpcwaitq.
At the same time an open is waiting for the inode deletion to complete in
__wait_on_freeing_inode.
If the open is either the open called by the state manager, or an open from
the same open owner that is holding the NFSv4 sequence id which causes the
OPEN from the state manager to wait for the sequence id on the Seqid_waitqueue,
then the state is deadlocked with kswapd.
The fix is simply to have layoutreturn ignore all errors except NFS4ERR_DELAY.
We already know that layouts are dropped on all server reboots, and that
it has to be coded to deal with the "forgetful client model" that doesn't
send layoutreturns.
Linus Torvalds [Wed, 4 Dec 2013 16:59:33 +0000 (08:59 -0800)]
Merge tag 'gpio-v3.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here are a few more GPIO patches, we're a bit noisy for being the GPIO
subsystem, mostly due to the new descriptor API, but all is getting
into shape.
- Fix compile warnings
- Fix overly talkative diagnostic messages from usual use cases wrt
GPIO descriptors
- Add a documentation 00-INDEX
- Use platform GPIOs as fallback when ACPI or device tree is used as
the primary means to get GPIO lines
- A bug fix for the MPC8572/MPC8536 fixing erroneous input data"
* tag 'gpio-v3.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpiolib: change a warning to debug message when failing to get gpio
powerpc/gpio: Fix the wrong GPIO input data on MPC8572/MPC8536
gpiolib: use platform GPIO mappings as fallback
Documentation: gpiolib: add 00-INDEX file
gpiolib: fix lookup of platform-mapped GPIOs
gpiolib: add missing declarations
Linus Torvalds [Wed, 4 Dec 2013 16:56:18 +0000 (08:56 -0800)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another batch of fixes for ARM SoCs for 3.13. The diffstat is large,
mostly because of:
- Another set of fixes to fix regressions caused by moving OMAP from
board files to DT. Tony thinks this was the last major set of
fixes, with maybe just a few small patches to follow.
- More fixes for Marvell platforms, most dealing with misdescribed
PCIe hardware, i.e. incorrect number of busses on some SoCs, etc.
The line delta adds up due to various ranges moving around when
this is fixed.
But there's also:
- Some smaller tweaks to defconfigs to make more boards bootable in
my test setup for better coverage.
- There are also a few other smaller fixes, a short series for at91,
a couple of reverts for ux500, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
arm: dts: socfpga: Change some clocks of gate-clk type to perip-clk
arm: socfpga: Enable ARM_TWD for socfpga
ARM: multi_v7_defconfig: enable SDHCI_BCM_KONA and MMC_BLOCK_MINORS=16
ARM: sunxi_defconfig: enable NFS, TMPFS, PRINTK_TIME and nfsroot support
ARM: multi_v7_defconfig: enable network for BeagleBone Black
ARM: dts: Fix the name of supplies for smsc911x shared by OMAP
ARM: OMAP2+: Powerdomain: Fix unchecked dereference of arch_pwrdm
ARM: dts: omap3-beagle: Add omap-twl4030 audio support
ARM: dts: omap4-sdp: Fix pin muxing for wl12xx
ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx
ARM: at91: fixed unresolved symbol "at91_pm_set_standby" when built without CONFIG_PM
ARM: at91: add usart3 alias to dtsi
ARM: at91: sama5d3: reduce TWI internal clock frequency
mmc: omap: Fix I2C dependency and make driver usable with device tree
mmc: omap: Fix DMA configuration to not rely on device id
ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
ARM: dts: AM33XX IGEP0033: add USB support
ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
ARM: dts: AM33XX BASE0033: add pinmux and user led support
...
Linus Torvalds [Wed, 4 Dec 2013 16:54:36 +0000 (08:54 -0800)]
Merge branch 'parisc-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parsic updates from Helge Deller:
- a fix for the mmap(MAP_FIXED|MAP_SHARED) syscall to the same address
which was already given in a previous call (fixes locale-gen on
debian)
- change the memory layout of the kernel to avoid the need for the
-mlong-calls compiler option (depends on commit 5ecbe3c3c690 -
"kernel/extable: fix address-checks for core_kernel and init areas")
- defconfig updates, e.g. use the SIL680 driver instead of the SIIMAGE
driver
- add more parisc machine names to the machine database
* 'parisc-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: update 64bit defconfigs and use SIL680 instead of SIIMAGE driver
parisc: remove CONFIG_MLONGCALLS=y from defconfigs
parisc: fix kernel memory layout in vmlinux.ld.S
parisc: use kernel_text_address() in unwind functions
parisc: remove empty SERIAL_PORT_DFNS in serial.h
parisc: add some more machine names to hardware database
parisc: fix mmap(MAP_FIXED|MAP_SHARED) to already mmapped address
Pull crypto fixes from Herbert Xu:
"This push fixes a number of crashes triggered by a previous crypto
self-test update. It also fixes a build problem in the caam driver,
as well as a concurrency issue in s390.
Finally there is a pair of fixes to bugs in the crypto scatterwalk
code and authenc that may lead to crashes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: testmgr - fix sglen in test_aead for case 'dst != src'
crypto: talitos - fix aead sglen for case 'dst != src'
crypto: caam - fix aead sglen for case 'dst != src'
crypto: ccm - Fix handling of zero plaintext when computing mac
crypto: s390 - Fix aes-xts parameter corruption
crypto: talitos - corrrectly handle zero-length assoc data
crypto: scatterwalk - Set the chain pointer indication bit
crypto: authenc - Find proper IV address in ablkcipher callback
crypto: caam - Add missing Job Ring include
Linus Torvalds [Wed, 4 Dec 2013 16:52:09 +0000 (08:52 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
- timekeeping: Cure a subtle drift issue on GENERIC_TIME_VSYSCALL_OLD
- nohz: Make CONFIG_NO_HZ=n and nohz=off command line option behave the
same way. Fixes a long standing load accounting wreckage.
- clocksource/ARM: Kconfig update to avoid ARM=n wreckage
- clocksource/ARM: Fixlets for the AT91 and SH clocksource/clockevents
- Trivial documentation update and kzalloc conversion from akpms pile
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
nohz: Fix another inconsistency between CONFIG_NO_HZ=n and nohz=off
time: Fix 1ns/tick drift w/ GENERIC_TIME_VSYSCALL_OLD
clocksource: arm_arch_timer: Hide eventstream Kconfig on non-ARM
clocksource: sh_tmu: Add clk_prepare/unprepare support
clocksource: sh_tmu: Release clock when sh_tmu_register() fails
clocksource: sh_mtu2: Add clk_prepare/unprepare support
clocksource: sh_mtu2: Release clock when sh_mtu2_register() fails
ARM: at91: rm9200: switch back to clockevents_config_and_register
tick: Document tick_do_timer_cpu
timer: Convert kmalloc_node(...GFP_ZERO...) to kzalloc_node(...)
NOHZ: Check for nohz active instead of nohz enabled
Takashi Iwai [Wed, 4 Dec 2013 12:59:45 +0000 (13:59 +0100)]
ALSA: hda - Fix silent output on MacBook Air 2,1
MacBook Air 2,1 has a fairly different pin assignment from its brother
MBA 1,1, and yet another quirks are needed for pin 0x18 and 0x19,
similarly like what iMac 9,1 requires, in order to make the sound
working on it.
Reported-and-tested-by: Bruno Prémont <bonbons@linux-vserver.org> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mika Kuoppala [Tue, 26 Nov 2013 14:14:33 +0000 (16:14 +0200)]
drm/i915: check context reset stats before relocations
Doing it early prevents moving and relocating objects in vain
for contexts that won't get any GPU time.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Takashi Iwai [Wed, 4 Dec 2013 11:40:59 +0000 (12:40 +0100)]
Merge tag 'asoc-v3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.13
A smattering of fixes here, some core ones for the rate combination
issues for things other than simple bitmasks, for readback of byte
controls and for updating the power of value muxes plus a bunch of
driver fixes of varying severity.
The warning fix in the i.MX FIQ driver is fixing a warning introduced
by a previous fix.
Chris Wilson [Wed, 4 Dec 2013 09:59:09 +0000 (09:59 +0000)]
drm/i915: Fix ordering of unbind vs unpin pages
It is useful to assert that if the object is bound, then it must have
its pages pinned to prevent the shrinker from reaping its backing store.
This is even more useful with the introduction of real-ppgtt whereupon
we may have the object bound into several vma, with each instance
pinning the backing store. This assertion breaks down during unbind
where we unpinned the backing store before decoupling the vma binding.
This can be fixed with a trivial reording of the unbind sequence, which
reinforces the
pin pages
bind to vma
...
unbind from vma
unpin pages
concept.
v2: Bonus comment
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Tested-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Deepak S [Fri, 29 Nov 2013 10:26:30 +0000 (15:56 +0530)]
drm/i915/vlv: Update Wait for FIFO and wait for 20 free entries. v3
On VLV, FIFO will be shared by both SW and HW. So, we read the
free entries through register and update dev_priv variable
and wait for only 20 entries to be free
From Deepak's follow-up mail explaining why vlv is special:
"On SB, Out of 64 FIFO Entries, 20 Entries will be used by HW and
remaining 44 will be used by the SW,. I think due to this reason, we
have a threshold of 20 Entries."
"On VLV, HW and SW can access all 64 fifo entries, I don't think
having a threshold of 20 Entries is mandatory on VLV. Also, since both
SW and HW can access all 64 Entries. I think on VLV, we need to update
the fifo_count before waiting for the FIFO."
v2: Apply mask when we read the number of free FIFO entries (Ville).
v3: Mask applied after reading the register (Deepak).
Signed-off-by: Deepak S <deepak.s@intel.com>
[danvet: Add further explanation from Deepak to commit message.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 28 Nov 2013 15:30:01 +0000 (17:30 +0200)]
drm/i915: Swap primary planes on gen2 for FBC
Only plane A is FBC capable on gen2 (like gen3), but the panel fitter
is hooked up to pipe B, so we want to prefer pipe B + plane A.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add the code comment Chris requested in his review.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 28 Nov 2013 15:29:59 +0000 (17:29 +0200)]
drm/i915: Reorganize FBC function pointer initializaition
Initialize the FBC vfuncs on gen2 and gen3 chipsets. Also make
a clean split for gen7+ vs. gen5+ vfunc initialization.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 28 Nov 2013 15:29:58 +0000 (17:29 +0200)]
drm/i915: Fix FBC1 plane checks for gen2
On gen2 and gen3 chipsets FBC is supported only on plane A. Fix (and
simplify) the plane checks in intel_update_fbc() accordingly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 28 Nov 2013 15:29:55 +0000 (17:29 +0200)]
drm/i915: Fix bogus FBC1 defines
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilons <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 2 Dec 2013 12:23:02 +0000 (14:23 +0200)]
drm/i915: Add REG_WRITE_FOOTER
Add a REG_WRITE_FOOTER macro as a counterpart to the REG_WRITE_HEADER.
The current code has the spin_lock() in the HEADER, but the
spin_unlock() is open coded, which looks rather confusing on the first
glance. A bit of additional symmetry might help.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dan Carpenter [Mon, 2 Dec 2013 08:11:18 +0000 (11:11 +0300)]
video: vt8500: fix error handling in probe()
We shouldn't kfree(fbi) because that was allocated with devm_kzalloc().
There were several error paths which returned directly instead of
releasing resources.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Johan Hovold [Tue, 22 Oct 2013 16:36:57 +0000 (18:36 +0200)]
atmel_lcdfb: fix module autoload
Add missing module device table which is needed for module autoloading.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
H. Peter Anvin [Wed, 20 Nov 2013 21:31:49 +0000 (13:31 -0800)]
x86-64, build: Always pass in -mno-sse
Always pass in the -mno-sse argument, regardless if
-preferred-stack-boundary is supported. We never want to generate SSE
instructions in the kernel unless we *really* know what we're doing.
According to H. J. Lu, any version of gcc new enough that we support
it at all should handle the -mno-sse option, so just add it
unconditionally.
If not, we could end up in the unfortunate situation where
we dereference a NULL pointer b/c we have cpuidle disabled.
This is the case when booting under Xen (which uses the
ACPI P/C states but disables the CPU idle driver) - and can
be easily reproduced when booting with cpuidle.off=1.
This problem also appears in 3.12 and could be a candidate for backport.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Olof Johansson [Tue, 3 Dec 2013 18:21:49 +0000 (10:21 -0800)]
ARM: multi_v7_defconfig: enable SDHCI_BCM_KONA and MMC_BLOCK_MINORS=16
Enable MMC/SD on the Broadcom mobile platforms, and increase the block
minors from the default 8 to 16 (since the Broadcom board by default
has root on the 8th partition).
Signed-off-by: Olof Johansson <olof@lixom.net> Cc: stable@vger.kernel.org # v3.12
Olof Johansson [Tue, 3 Dec 2013 02:40:50 +0000 (18:40 -0800)]
ARM: sunxi_defconfig: enable NFS, TMPFS, PRINTK_TIME and nfsroot support
This enables a few more options on the sunxi defconfigs such that I can
use nfsroot to boot them (there is no local storage support yet). It
also enables PRINTK_TIME and tmpfs since it's a common distro requirement.
Olof Johansson [Tue, 3 Dec 2013 02:24:38 +0000 (18:24 -0800)]
Merge tag 'omap-for-v3.13/more-dt-regressions' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Few more legacy booting vs device tree booting fixes that people
have noticed while booting things with device tree for things like
omap4 WLAN, smsc911x, and beagle audio. Hopefully this will be it
for the legacy booting vs device tree fixes for this -rc cycle.
* tag 'omap-for-v3.13/more-dt-regressions' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix the name of supplies for smsc911x shared by OMAP
ARM: OMAP2+: Powerdomain: Fix unchecked dereference of arch_pwrdm
ARM: dts: omap3-beagle: Add omap-twl4030 audio support
ARM: dts: omap4-sdp: Fix pin muxing for wl12xx
ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx
Olof Johansson [Mon, 2 Dec 2013 17:16:08 +0000 (09:16 -0800)]
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
From Nicolas Ferre:
AT91: second round of fixes for 3.13
- reduce IP frequency for I2C on sama5d3
- missing aliases directive for USART3 on 9x5 family
- a PM symbol is missing if !CONFIG_PM
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: fixed unresolved symbol "at91_pm_set_standby" when built without CONFIG_PM
ARM: at91: add usart3 alias to dtsi
ARM: at91: sama5d3: reduce TWI internal clock frequency
Olof Johansson [Sun, 1 Dec 2013 19:51:24 +0000 (11:51 -0800)]
Merge tag 'mvebu-dt-fixes-3.13' of git://git.infradead.org/linux-mvebu into fixes
From Jason Cooper, mvebu DT fixes for v3.13:
- mvebu
- PCIe fixes now that we have test devices with more ports.
- fix access to coherency registers
* tag 'mvebu-dt-fixes-3.13' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: re-enable PCIe on Armada 370 DB
ARM: mvebu: use the virtual CPU registers to access coherency registers
ARM: mvebu: fix second and third PCIe unit of Armada XP mv78260
ARM: mvebu: second PCIe unit of Armada XP mv78230 is only x1 capable
Olof Johansson [Wed, 27 Nov 2013 03:29:24 +0000 (19:29 -0800)]
Merge tag 'omap-for-v3.13/fixes-against-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Some omap related fixes that have come up with people moving to device
tree only based booting for omap2+.
The series contains a handful of fixes for the igep boards as they were
one of the first omap3 boards to jump over completely to device tree
based booting. So these can be considered regressions compared to
booting igep in legacy mode with board files in v3.12.
Also included are few other device tree vs legacy booting regressions:
- yet more missing omap3 .dtsi entries that have showed up booting
various boards with device tree only
- n900 eMMC device tree fix
- fixes for beagle USB EHCI
- two fixes to make omap2420 MMC work
As we're moving omap2+ to be device tree only for v3.14, I'd like to
have v3.13 work equally well for legacy based booting and device tree
based booting. So there will be likely few more device tree related
booting patches trickling in.
This series also includes a regression fix for the omap timer posted
mode that may wrongly stay on from the bootloader for some SoCs.
* tag 'omap-for-v3.13/fixes-against-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
mmc: omap: Fix I2C dependency and make driver usable with device tree
mmc: omap: Fix DMA configuration to not rely on device id
ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
ARM: dts: AM33XX IGEP0033: add USB support
ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
ARM: dts: AM33XX BASE0033: add pinmux and user led support
ARM: dts: AM33XX BASE0033: add pinmux and hdmi node to enable display
ARM: dts: omap3-igep0020: Add pinmuxing for DVI output
ARM: dts: omap3-igep0020: Add pinmux setup for i2c devices
ARM: dts: omap3-igep: Update to use the TI AM/DM37x processor
ARM: dts: omap3-igep: Add support for LBEE1USJYC WiFi connected to SDIO
ARM: dts: omap3-igep: Fix bus-width for mmc1
ARM: OMAP2+: dss-common: change IGEP's DVI DDC i2c bus
ARM: OMAP2+: Disable POSTED mode for errata i103 and i767
ARM: OMAP2+: Fix eMMC on n900 with device tree
ARM: OMAP2+: Add fixed regulator to omap2plus_defconfig
ARM: OMAP2+: Fix more missing data for omap3.dtsi file
Chris Wilson [Mon, 2 Dec 2013 09:57:16 +0000 (09:57 +0000)]
drm/i915: Add a timing breadcrumb to panel waits
When inspecting reports that boot/suspend/resume times are unusual it
would be useful to clearly identify the time we must spend waiting for
the hardware to complete its task. In this case we have a notification
before we start waiting for the panel to change state, but none
afterwards - which would be useful.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
projects / linux-beck.git / log