Fix regression introduced by commit 787f9fd23283 ("atmel_lcdfb: support
16bit BGR:565 mode, remove unsupported 15bit modes") which broke 16-bpp
modes for older SOCs which use IBGR:555 (msb is intensity) rather
than BGR:565.
Use SOC-type to determine the pixel layout.
Tested on at91sam9263 and at91sam9g45.
Acked-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 10b63956 ("UAPI: Plumb the UAPI Kbuilds into the user header
installation and checking") introduced a dependency of make 3.81
due to use of $(or ...)
We do not want to lift the requirement to gmake 3.81 just yet...
Included are a straightforward conversion to $(if ...)
Bisected-and-tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: David Howells <dhowells@redhat.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Michal Marek <mmarek@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original documentation for NAND_NO_READRDY included "True for all
large page devices, as they do not support autoincrement." I was
conflating "not support autoincrement" with the NAND_NO_AUTOINCR option,
which was in fact doing nothing. So, when I dropped NAND_NO_AUTOINCR, I
concluded that I then could harmlessly drop NAND_NO_READRDY. But of
course the fact the NAND_NO_AUTOINCR was doing nothing didn't mean
NAND_NO_READRDY was doing nothing...
So, NAND_NO_READRDY is re-introduced as NAND_NEED_READRDY and applied
only to those few remaining small-page NAND which needed it in the first
place.
Reported-by: Alexander Shiyan <shc_work@mail.ru> Tested-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Doing this would reliably fail with -EBUSY for me:
# mount /dev/sdb2 /mnt/scratch; umount /mnt/scratch; mkfs.btrfs -f /dev/sdb2
...
unable to open /dev/sdb2: Device or resource busy
because mkfs.btrfs tries to open the device O_EXCL, and somebody still has it.
Using systemtap to track bdev gets & puts shows a kworker thread doing a
blkdev put after mkfs attempts a get; this is left over from the unmount
path:
so unmount might complete before __free_device fires & does its blkdev_put.
Adding an rcu_barrier() to btrfs_close_devices() causes unmount to wait
until all blkdev_put()s are done, and the device is truly free once
unmount completes.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our flush_tlb_kernel_range() implementation calls __tlb_flush_mm() with
&init_mm as argument. __tlb_flush_mm() however will only flush tlbs
for the passed in mm if its mm_cpumask is not empty.
For the init_mm however its mm_cpumask has never any bits set. Which in
turn means that our flush_tlb_kernel_range() implementation doesn't
work at all.
This can be easily verified with a vmalloc/vfree loop which allocates
a page, writes to it and then frees the page again. A crash will follow
almost instantly.
To fix this remove the cpumask_empty() check in __tlb_flush_mm() since
there shouldn't be too many mms with a zero mm_cpumask, besides the
init_mm of course.
The current machine check code uses the registers stored by the machine
in the lowcore at __LC_GPREGS_SAVE_AREA as the registers of the interrupted
context. The registers 0-7 of a user process can get clobbered if a machine
checks interrupts the execution of a critical section in entry[64].S.
The reason is that the critical section cleanup code may need to modify
the PSW and the registers for the previous context to get to the end of a
critical section. If registers 0-7 have to be replaced the relevant copy
will be in the registers, which invalidates the copy in the lowcore. The
machine check handler needs to explicitly store registers 0-7 to the stack.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1d9d8639c063 ("perf,x86: fix kernel crash with PEBS/BTS after
suspend/resume") introduces a link failure since
perf_restore_debug_store() is only defined for CONFIG_CPU_SUP_INTEL:
arch/x86/power/built-in.o: In function `restore_processor_state':
(.text+0x45c): undefined reference to `perf_restore_debug_store'
Fix it by defining the dummy function appropriately.
Commit 1d9d8639c063 ("perf,x86: fix kernel crash with PEBS/BTS after
suspend/resume") fixed a crash when doing PEBS performance profiling
after resuming, but in using init_debug_store_on_cpu() to restore the
DS_AREA mtrr it also resulted in a new WARN_ON() triggering.
init_debug_store_on_cpu() uses "wrmsr_on_cpu()", which in turn uses CPU
cross-calls to do the MSR update. Which is not really valid at the
early resume stage, and the warning is quite reasonable. Now, it all
happens to _work_, for the simple reason that smp_call_function_single()
ends up just doing the call directly on the CPU when the CPU number
matches, but we really should just do the wrmsr() directly instead.
This duplicates the wrmsr() logic, but hopefully we can just remove the
wrmsr_on_cpu() version eventually.
This adds additional error checking to the private edma api implementation
to catch the case where the edma_alloc_slot() has an invalid controller
parameter. The edma dmaengine wrapper driver relies on this condition
being handled in order to avoid setting up a second edma dmaengine
instance on DA830.
Verfied using a DA850 with the second EDMA controller platform instance
removed to simulate a DA830 which only has a single EDMA controller.
Reported-by: Tomas Novotny <tomas@novotny.cz> Signed-off-by: Matt Porter <mporter@ti.com> Tested-by: Tomas Novotny <tomas@novotny.cz> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch change the kernel VSID range so that we limit VSID_BITS to 37.
This enables us to support 64TB with 65 bit VA (37+28). Without this patch
we have boot hangs on platforms that only support 65 bit VA.
With this patch we now have proto vsid generated as below:
We first generate a 37-bit "proto-VSID". Proto-VSIDs are generated
from mmu context id and effective segment id of the address.
For user processes max context id is limited to ((1ul << 19) - 5)
for kernel space, we use the top 4 context ids to map address as below
0x7fffc - [ 0xc000000000000000 - 0xc0003fffffffffff ]
0x7fffd - [ 0xd000000000000000 - 0xd0003fffffffffff ]
0x7fffe - [ 0xe000000000000000 - 0xe0003fffffffffff ]
0x7ffff - [ 0xf000000000000000 - 0xf0003fffffffffff ]
Commit 44ae3ab3358e962039c36ad4ae461ae9fb29596c forgot to update
the entry for the 970MP rev 1.0 processor when moving some CPU
features bits to the MMU feature bit mask. This breaks booting
on some rare G5 models using that chip revision.
Commit f5339277eb8d3aed37f12a27988366f68ab68930 accidentally removed
more than just iSeries bits and took out the call to stab_initialize()
thus breaking support for POWER3 processors.
Put it back. (Yes, nobody noticed until now ...)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Good job. I was too lazy to bisect for bad commit;)
Reading the code I found problematic kthread_should_stop call from netlink
connector which causes the oops. After applying a patch, I've been testing
owfs+w1 setup for nearly two days and it seems to work very reliable (no
hangs, no memleaks etc).
More detailed description and possible fix is given below:
Function w1_search can be called from either kthread or netlink callback.
While the former works fine, the latter causes oops due to kthread_should_stop
invocation.
This patch adds a check if w1_search is serving netlink command, skipping
kthread_should_stop invocation if so.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com> Acked-by: Evgeniy Polyakov <zbr@ioremap.net> Cc: Josh Boyer <jwboyer@gmail.com> Tested-by: Sven Geggus <lists@fuchsschwanzdomain.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8a1861d997 ("w1-gpio: Simplify & get rid of defines") changed
(apparently unknowingly) the driver to a hotpluggable platform-device
driver but did not not update the section markers for probe and remove
(to __devinit/exit, which have since been removed). A later commit fixed
the section mismatch for probe, but left remove marked with __exit.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On LTC2978, only READ_TEMPERATURE is supported. It reports
the internal junction temperature. This register is unpaged.
On LTC3880, READ_TEMPERATURE and READ_TEMPERATURE2 are supported.
READ_TEMPERATURE is paged and reports external temperatures.
READ_TEMPERATURE2 is unpaged and reports the internal junction
temperature.
Fix regression introduced by commit d2323cf773 ("onewire: w1-gpio: add
ext_pullup_enable pin in platform data") which added a gpio entry to the
platform data, but did not add the required initialisers to the board
files using it. Consequently, the driver would request gpio 0 at probe,
which could break other uses of the corresponding pin.
On AT91 requesting gpio 0 changes the pin muxing for PIOA0, which, for
instance, breaks SPI0 on at91sam9g20.
snd_seq_timer_open() didn't catch the whole error path but let through
if the timer id is a slave. This may lead to Oops by accessing the
uninitialized pointer.
This patch fixes a kernel crash when using precise sampling (PEBS)
after a suspend/resume. Turns out the CPU notifier code is not invoked
on CPU0 (BP). Therefore, the DS_AREA (used by PEBS) is not restored properly
by the kernel and keeps it power-on/resume value of 0 causing any PEBS
measurement to crash when running on CPU0.
The workaround is to add a hook in the actual resume code to restore
the DS Area MSR value. It is invoked for all CPUS. So for all but CPU0,
the DS_AREA will be restored twice but this is harmless.
The ethernet controller used on kirkwood looses its MAC address
register contents when the corresponding clock is gated. As soon as
mv643xx_eth is built as module, the clock gets gated and when loading
the module, the MAC address is gone.
Proper DT support for the mv643xx_eth driver is expected soon, so we add
a workaround to always enable ge0/ge1 clocks on kirkwood. This workaround
is also already used on non-DT kirkwood kernels.
Reported-by: Simon Baatz <gmbnomis@gmail.com> Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Tested-by: Simon Baatz <gmbnomis@gmail.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looking back at that thread there were two issues in the original patch.
1) The I/O ports for the UARTs are within BAR2 not BAR0. This can been seen in the original post.
2) A serial quirk isn't needed as these cards have no memory in BAR0 which makes pci_plx9050_init just return.
This patch fixes the 4 port support to use BAR2, removes the bogus quirk and adds support for the 8 port card.
$ lspci -vvv -n -s 00:08.0
00:08.0 0780: 10b5:9050 (rev 01)
Subsystem: 10b5:1588
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 17
Region 1: I/O ports at ff00 [size=128]
Region 2: I/O ports at fe00 [size=64]
Region 3: I/O ports at fd00 [size=8]
Capabilities: <access denied>
Kernel driver in use: serial
$ dmesg | grep 0000:00:08.0:
[ 0.083320] pci 0000:00:08.0: [10b5:9050] type 0 class 0x000780
[ 0.083355] pci 0000:00:08.0: reg 14: [io 0xff00-0xff7f]
[ 0.083369] pci 0000:00:08.0: reg 18: [io 0xfe00-0xfe3f]
[ 0.083382] pci 0000:00:08.0: reg 1c: [io 0xfd00-0xfd07]
[ 0.083460] pci 0000:00:08.0: PME# supported from D0 D3hot
[ 1.212867] 0000:00:08.0: ttyS4 at I/O 0xfe00 (irq = 17) is a 16550A
[ 1.233073] 0000:00:08.0: ttyS5 at I/O 0xfe08 (irq = 17) is a 16550A
[ 1.253270] 0000:00:08.0: ttyS6 at I/O 0xfe10 (irq = 17) is a 16550A
[ 1.273468] 0000:00:08.0: ttyS7 at I/O 0xfe18 (irq = 17) is a 16550A
[ 1.293666] 0000:00:08.0: ttyS8 at I/O 0xfe20 (irq = 17) is a 16550A
[ 1.313863] 0000:00:08.0: ttyS9 at I/O 0xfe28 (irq = 17) is a 16550A
[ 1.334061] 0000:00:08.0: ttyS10 at I/O 0xfe30 (irq = 17) is a 16550A
[ 1.354258] 0000:00:08.0: ttyS11 at I/O 0xfe38 (irq = 17) is a 16550A
Signed-off-by: Scott Ashcroft <scott.ashcroft@talk21.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that login from util-linux is forced to drop all references to a
TTY which it wants to hangup (to reach reference count 1) we are
seeing issues with telnet. When login closes its last reference to the
slave PTY, it also resets packet mode on the *master* side. And we
have a race here.
What telnet does is fork+exec of `login'. Then there are two
scenarios:
* `login' closes the slave TTY and resets thus master's packet mode,
but even now telnet properly sets the mode, or
* `telnetd' sets packet mode on the master, `login' closes the slave
TTY and resets master's packet mode.
The former case is OK. However the latter happens in much more cases,
by the order of magnitude to be precise. So when one tries to login to
such a messed telnet setup, they see the following:
inux login:
ogin incorrect
Note the missing first letters -- telnet thinks it is still in the
packet mode, so when it receives "linux login" from `login', it
considers "l" as the type of the packet and strips it.
SuS does not mention how the implementation should behave. Both BSDs I
checked (Free and Net) do not reset the flag upon the last close.
By this I am resurrecting an old bug, see References. We are hitting
it regularly now, i.e. with updated util-linux, ergo login.
Here, I am changing a behavior introduced back in 2.1 times. It would
better have a long time testing before goes upstream.
We added a warning to flush_to_ldisc to report cases when it is called
with a NULL tty. It was for debugging purposes and it lead to a
patchset from Peter Hurley. The patchset however did not make it to
3.9, so disable the warning now to not disturb people.
We can re-add it when the series is in and we are hunting for another
bugs.
Reported-by: David Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig symbol SERIAL_S3C2412 got removed in commit da121506eb03ee5daea55404709110b798bd61d9 ("serial: samsung: merge
probe() function from all SoC specific extensions"). But it also added a
last reference to that symbol. The commit and the tree make clear that
CPU_S3C2412 should have been used instead.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This could have been either ARCH_S5P64X0 or CPU_S5P6450. Looking at
commit 2555e663b367b8d555e76023f4de3f6338c28d6c ("ARM: S5P64X0: Add UART
serial support for S5P6450") - which added this typo - makes clear this
should be CPU_S5P6450.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit 835d844d1 (8250_pnp: do pnp probe before legacy probe), the
8250 driver was renamed to 8250_core. This means any existing usage of
the 8259.<xxxx> module parameters or as a kernel command line switch is
now broken, as the 8250_core driver doesn't parse options belonging to
something called "8250".
To solve this, we redefine the module options in a dummy function using
a redefined MODULE_PARAM_PREFX when built into the kernel. In the case
where we're building as a module, we provide an alias to the old 8250
name. The dummy function prevents compiler errors due to global variable
redefinitions that happen as part of the module_param_ macro expansions.
The InsydeH2O BIOS (version dated 09/12/2011) has the following in
its pnp resouces for its serial ports:
$ cat /sys/bus/pnp/devices/00:0b/resources
state = active
io disabled
irq disabled
We do not check if the resources are disabled, and create a bogus
ttyS* device. Since commit 835d844d1a28e (8250_pnp: do pnp probe
before legacy probe) we get a bogus ttyS0, which prevents the legacy
probe from detecting it.
Note, the BIOS can also be upgraded, fixing this problem, but for people
who can't do that, this fix is needed.
Reported-by: Vincent Deffontaines <vincent@gryzor.com> Tested-by: Vincent Deffontaines <vincent@gryzor.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ext3_msg() takes the printk prefix as the second parameter and the
format string as the third parameter. Two callers of ext3_msg omit the
prefix and pass the format string as the second parameter and the first
parameter to the format string as the third parameter. In both cases
this string comes from an arbitrary source. Which means the string may
contain format string characters, which will
lead to undefined and potentially harmful behavior.
The issue was introduced in commit 4cf46b67eb("ext3: Unify log messages
in ext3") and is fixed by this patch.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the new signal handlers are set up, the location of sa_restorer is
not cleared, leaking a parent process's address space location to
children. This allows for a potential bypass of the parent's ASLR by
examining the sa_restorer value returned when calling sigaction().
Based on what should be considered "secret" about addresses, it only
matters across the exec not the fork (since the VMAs haven't changed
until the exec). But since exec sets SIG_DFL and keeps sa_restorer,
this is where it should be fixed.
Given the few uses of sa_restorer, a "set" function was not written
since this would be the only use. Instead, we use
__ARCH_HAS_SA_RESTORER, as already done in other places.
As pointed out by Dan Carpenper in
<http://driverdev.linuxdriverproject.org/pipermail/devel/2013-February/036025.html>,
the dt9812 comedi driver's use of the `chanspec` member of `struct
comedi_insn` as a channel number is incorrect. Change it to use
`CR_CHAN(insn->chanspec)` as the channel number (where `insn` is a
pointer to the `struct comedi_insn` being processed).
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Anders Blomdell <anders.blomdell@control.lth.se> Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1661) fixes a rather obscure bug in ehci-hcd. In a
couple of places, the driver compares the DMA address stored in a QH's
overlay region with the address of a particular qTD, in order to see
whether that qTD is the one currently being processed by the hardware.
(If it is then the status in the QH's overlay region is more
up-to-date than the status in the qTD, and if it isn't then the
overlay's value needs to be adjusted when the QH is added back to the
active schedule.)
However, DMA address in the overlay region isn't always valid. It
sometimes will contain a stale value, which may happen by coincidence
to be equal to a qTD's DMA address. Instead of checking the DMA
address, we should check whether the overlay region is active and
valid. The patch tests the ACTIVE bit in the overlay, and clears this
bit when the overlay becomes invalid (which happens when the
currently-executing URB is unlinked).
This is the second part of a fix for the regression reported at:
This reverts commit 200e0d99 ("USB: storage: optimize to match the
Huawei USB storage devices and support new switch command" and the
followup bugfix commit cd060956 ("USB: storage: properly handle
the endian issues of idProduct").
The commit effectively added a large number of Huawei devices to
the deprecated usb-storage mode switching logic. Many of these
devices have been in use and supported by the userspace
usb_modeswitch utility for years. Forcing the switching inside
the kernel causes a number of regressions as a result of ignoring
existing onfigurations, and also completely takes away the ability
to configure mode switching per device/system/user.
Known regressions caused by this:
- Some of the devices support multiple modes, using different
switching commands. There are existing configurations taking
advantage of this.
- There is a real use case for disabling mode switching and
instead mounting the exposed storage device. This becomes
impossible with switching logic inside the usb-storage driver.
- At least on device fail as a result of the usb-storage switching
command, becoming completely unswitchable. This is possibly a
firmware bug, but still a regression because the device work as
expected using usb_modeswitch defaults.
In-kernel mode switching was deprecated years ago with the
development of the more user friendly userspace alternatives. The
existing list of devices in usb-storage was only kept to prevent
breaking already working systems. The long term plan is to remove
the list, not to add to it. Ref:
http://permalink.gmane.org/gmane.linux.usb.general/28543
The Rigblaster Advantage is an amateur radio interface sold by West Mountain
Radio. It contains a cp210x serial interface but the device ID is not in
the driver.
Signed-off-by: Steve Conklin <sconklin@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the Lake Shore Cryotronics devices to
the CP210x driver.
These lines are ported from cp210x driver distributed by Lake Shore web site:
http://www.lakeshore.com/Documents/Lake%20Shore%20cp210x-3.0.0.tar.gz
and licensed under the terms of GPLv2.
Moreover, I've tested this changes with Lake Shore 335 in my labs.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3921426 (usb: dwc3: core: move
event buffer allocation out of
dwc3_core_init()) introduced a memory leak
of the coherent memory we use as event
buffers on dwc3 driver.
If the driver is compiled as a dynamically
loadable module and use constantly loads
and unloads the driver, we will continue
to leak the coherent memory allocated during
->probe() because dwc3_free_event_buffers()
is never called during ->remove().
Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes this build failure:
gcc -Wall -Wextra -g -lpthread -I../include -o testusb testusb.c
gcc -Wall -Wextra -g -lpthread -I../include -o ffs-test ffs-test.c
In file included from ffs-test.c:41:0:
../../include/linux/usb/functionfs.h:4:39: fatal error:
uapi/linux/usb/functionfs.h: No such file or directory
compilation terminated.
make: *** [ffs-test] Error 1
Signed-off-by: Maxin B. John <maxin.john@enea.com> Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The buffer for responses must not overflow.
If this would happen, set a flag, drop the data and return
an error after user space has read all remaining data.
Signed-off-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code currently only supports one virtio-rng device at a time.
Invoking guests with multiple devices causes the guest to blow up.
Check if we've already registered and initialised the driver. Also
cleanup in case of registration errors or hot-unplug so that a new
device can be used.
Reported-by: Peter Krempa <pkrempa@redhat.com> Reported-by: <yunzheng@redhat.com> Signed-off-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't allowing sharing the root directory with processes in a
different user namespace. There doesn't seem to be any point, and to
allow it would require the overhead of putting a user namespace
reference in fs_struct (for permission checks) and incrementing that
reference count on practically every call to fork.
So just perform the inexpensive test of forbidding sharing fs_struct
acrosss processes in different user namespaces. We already disallow
other forms of threading when unsharing a user namespace so this
should be no real burden in practice.
This updates setns, clone, and unshare to disallow multiple user
namespaces sharing an fs_struct.
WARNING: drivers/w1/masters/w1-gpio.o(.data+0x188): Section mismatch in
reference from the variable w1_gpio_driver to the function
.init.text:w1_gpio_probe()
The variable w1_gpio_driver references
the function __init w1_gpio_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
A USB 3.0 device can transition to the Inactive state if a U1 or U2 exit
transition fails. The current code in hub_events simply issues a warm
reset, but does not call any pre-reset or post-reset driver methods (or
unbind/rebind drivers without them). Therefore the drivers won't know
their device has just been reset.
hub_events should instead call usb_reset_device. This means
hub_port_reset now needs to figure out whether it should issue a warm
reset or a hot reset.
Remove the FIXME note about needing disconnect() for a NOTATTACHED
device. This patch fixes that.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a hot reset fails on a USB 3.0 port, the current port reset code
recursively calls hub_port_reset inside hub_port_wait_reset. This isn't
ideal, since we should avoid recursive calls in the kernel, and it also
doesn't allow us to issue multiple warm resets on reset failures.
Rip out the recursive call. Instead, add code to hub_port_reset to
issue a warm reset if the hot reset fails, and try multiple warm resets
before giving up on the port.
In hub_port_wait_reset, remove the recursive call and re-indent. The
code is basically the same, except:
1. It bails out early if the port has transitioned to Inactive or
Compliance Mode after the reset completed.
2. It doesn't consider a connect status change to be a failed reset. If
multiple warm resets needed to be issued, the connect status may have
changed, so we need to ignore that and look at the port link state
instead. hub_port_reset will now do that.
3. It unconditionally sets udev->speed on all types of successful
resets. The old recursive code would set the port speed when the second
hub_port_reset returned.
The old code did not handle connected devices needing a warm reset well.
There were only two situations that the old code handled correctly: an
empty port needing a warm reset, and a hot reset that migrated to a warm
reset.
When an empty port needed a warm reset, hub_port_reset was called with
the warm variable set. The code in hub_port_finish_reset would skip
telling the USB core and the xHC host that the device was reset, because
otherwise that would result in a NULL pointer dereference.
When a USB 3.0 device reset migrated to a warm reset, the recursive call
made the call stack look like this:
hub_port_reset(warm = false)
hub_wait_port_reset(warm = false)
hub_port_reset(warm = true)
hub_wait_port_reset(warm = true)
hub_port_finish_reset(warm = true)
(return up the call stack to the first wait)
hub_port_finish_reset(warm = false)
The old code didn't want to notify the USB core or the xHC host of device reset
twice, so it only did it in the second call to hub_port_finish_reset,
when warm was set to false. This was necessary because
before patch two ("USB: Ignore xHCI Reset Device status."), the USB core
would pay attention to the xHC Reset Device command error status, and
the second call would always fail.
Now that we no longer have the recursive call, and warm can change from
false to true in hub_port_reset, we need to have hub_port_finish_reset
unconditionally notify the USB core and the xHC of the device reset.
In hub_port_finish_reset, unconditionally clear the connect status
change (CSC) bit for USB 3.0 hubs when the port reset is done. If we
had to issue multiple warm resets for a device, that bit may have been
set if the device went into SS.Inactive and then was successfully warm
reset.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The next patch will refactor the hub port code to rip out the recursive
call to hub_port_reset on a failed hot reset. In preparation for that,
make sure all code paths can deal with being called with a NULL udev.
The usb_device will not be valid if warm reset was issued because a port
transitioned to the Inactive or Compliance Mode on a device connect.
This patch should have no effect on current behavior.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The EHCI host controller needs to prevent EHCI initialization when the
UHCI or OHCI companion controller is in the middle of a port reset. It
uses ehci_cf_port_reset_rwsem to do this. USB 3.0 hubs can't be under
an EHCI host controller, so it makes no sense to down the semaphore for
USB 3.0 hubs. It also makes the warm port reset code more complex.
Don't down ehci_cf_port_reset_rwsem for USB 3.0 hubs.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UEFI variables are typically stored in flash. For various reasons, avaiable
space is typically not reclaimed immediately upon the deletion of a
variable - instead, the system will garbage collect during initialisation
after a reboot.
Some systems appear to handle this garbage collection extremely poorly,
failing if more than 50% of the system flash is in use. This can result in
the machine refusing to boot. The safest thing to do for the moment is to
forbid writes if they'd end up using more than half of the storage space.
We can make this more finegrained later if we come up with a method for
identifying the broken machines.
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com> Cc: Josh Boyer <jwboyer@redhat.com> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Problem]
There is a scenario which efi_pstore fails to log messages in a panic case.
- CPUA holds an efi_var->lock in either efivarfs parts
or efi_pstore with interrupt enabled.
- CPUB panics and sends IPI to CPUA in smp_send_stop().
- CPUA stops with holding the lock.
- CPUB kicks efi_pstore_write() via kmsg_dump(KSMG_DUMP_PANIC)
but it returns without logging messages.
[Patch Description]
This patch disables an external interruption while holding efivars->lock
as follows.
In efi_pstore_write() and get_var_data(), spin_lock/spin_unlock is
replaced by spin_lock_irqsave/spin_unlock_irqrestore because they may
be called in an interrupt context.
In other functions, they are replaced by spin_lock_irq/spin_unlock_irq.
because they are all called from a process context.
By applying this patch, we can avoid the problem above with
a following senario.
- CPUA holds an efi_var->lock with interrupt disabled.
- CPUB panics and sends IPI to CPUA in smp_send_stop().
- CPUA receives the IPI after releasing the lock because it is
disabling interrupt while holding the lock.
- CPUB waits for one sec until CPUA releases the lock.
- CPUB kicks efi_pstore_write() via kmsg_dump(KSMG_DUMP_PANIC)
And it can hold the lock successfully.
Signed-off-by: Seiji Aguchi <seiji.aguchi@hds.com> Acked-by: Mike Waychison <mikew@google.com> Acked-by: Matt Fleming <matt.fleming@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Cc: Josh Boyer <jwboyer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The prompt to enable DYNAMIC_FTRACE (the ability to nop and
enable function tracing at run time) had a confusing statement:
"enable/disable ftrace tracepoints dynamically"
This was written before tracepoints were added to the kernel,
but now that tracepoints have been added, this is very confusing
and has confused people enough to give wrong information during
presentations.
Not only that, I looked at the help text, and it still references
that dreaded daemon that use to wake up once a second to update
the nop locations and brick NICs, that hasn't been around for over
five years.
In commit 466921c we added a hack to set the paca data_offset to zero so
that per-cpu accesses would work on the boot cpu prior to per-cpu areas
being setup. This fixed a problem with lockdep touching per-cpu areas
very early in boot.
However if we combine CONFIG_LOCK_STAT=y with any of the PPC_EARLY_DEBUG
options, we can hit the same problem in udbg_early_init(). To avoid that
we need to set the data_offset of the boot_paca also. So factor out the
fixup logic and call it for both the boot_paca, and "the paca of the
boot cpu".
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Tested-by: Geoff Levand <geoff@infradead.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DT support for kirkwood was first introduced, there was no clock
infrastructure. As a result, we had to manually pass the
clock-frequency to the driver from the device node.
Unfortunately, on kirkwood, with minimal config or all module configs,
clock-frequency breaks booting because of_serial doesn't consume the
gate_clk when clock-frequency is defined.
The end result on kirkwood is that runit gets gated, and then the boot
fails when the kernel tries to write to the serial port.
Fix the issue by removing the clock-frequency parameter from all
kirkwood dts files.
Booted on dreamplug without earlyprintk and successfully logged in via
ttyS0.
Reported-by: Simon Baatz <gmbnomis@gmail.com> Tested-by: Simon Baatz <gmbnomis@gmail.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09f6ffde2e (USB: EHCI: fix build error by making ChipIdea host a normal
EHCI driver) introduced CONFIG_USB_EHCI_HCD as a dependency for USB_CHIPIDEA_HOST.
Select CONFIG_USB_EHCI_HCD, so that USB host can be functional again.
The kirkwood SoC GPIO cores use the runit clock. Add code to
clk_prepare_enable() runit, otherwise there is a danger of locking up
the SoC by accessing the GPIO registers when runit clock is not
ticking.
Reported-by: Simon Baatz <gmbnomis@gmail.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Simon Baatz <gmbnomis@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Marvell RTC on Kirkwood makes use of the runit clock. Ensure the
driver clk_prepare_enable() this clock, otherwise there is a danger
the SoC will lockup when accessing RTC registers with the clock
disabled.
Reported-by: Simon Baatz <gmbnomis@gmail.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Simon Baatz <gmbnomis@gmail.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If you open a pipe for neither read nor write, the pipe code will not
add any usage counters to the pipe, causing the 'struct pipe_inode_info"
to be potentially released early.
That doesn't normally matter, since you cannot actually use the pipe,
but the pipe release code - particularly fasync handling - still expects
the actual pipe infrastructure to all be there. And rather than adding
NULL pointer checks, let's just disallow this case, the same way we
already do for the named pipe ("fifo") case.
This is ancient going back to pre-2.4 days, and until trinity, nobody
naver noticed.
Reported-by: Dave Jones <davej@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looking at mm/process_vm_access.c:process_vm_rw() and comparing it to
compat_process_vm_rw() shows that the compatibility code requires an
explicit "access_ok()" check before calling
compat_rw_copy_check_uvector(). The same difference seems to appear when
we compare fs/read_write.c:do_readv_writev() to
fs/compat.c:compat_do_readv_writev().
This subtle difference between the compat and non-compat requirements
should probably be debated, as it seems to be error-prone. In fact,
there are two others sites that use this function in the Linux kernel,
and they both seem to get it wrong:
Now shifting our attention to fs/aio.c, we see that aio_setup_iocb()
also ends up calling compat_rw_copy_check_uvector() through
aio_setup_vectored_rw(). Unfortunately, the access_ok() check appears to
be missing. Same situation for
security/keys/compat.c:compat_keyctl_instantiate_key_iov().
I propose that we add the access_ok() check directly into
compat_rw_copy_check_uvector(), so callers don't have to worry about it,
and it therefore makes the compat call code similar to its non-compat
counterpart. Place the access_ok() check in the same location where
copy_from_user() can trigger a -EFAULT error in the non-compat code, so
the ABI behaviors are alike on both compat and non-compat.
While we are here, fix compat_do_readv_writev() so it checks for
compat_rw_copy_check_uvector() negative return values.
And also, fix a memory leak in compat_keyctl_instantiate_key_iov() error
handling.
There is a race in install_user_keyrings() that can cause a NULL pointer
dereference when called concurrently for the same user if the uid and
uid-session keyrings are not yet created. It might be possible for an
unprivileged user to trigger this by calling keyctl() from userspace in
parallel immediately after logging in.
Assume that we have two threads both executing lookup_user_key(), both
looking for KEY_SPEC_USER_SESSION_KEYRING.
THREAD A THREAD B
=============================== ===============================
==>call install_user_keyrings();
if (!cred->user->session_keyring)
==>call install_user_keyrings()
...
user->uid_keyring = uid_keyring;
if (user->uid_keyring)
return 0;
<==
key = cred->user->session_keyring [== NULL]
user->session_keyring = session_keyring;
atomic_inc(&key->usage); [oops]
At the point thread A dereferences cred->user->session_keyring, thread B
hasn't updated user->session_keyring yet, but thread A assumes it is
populated because install_user_keyrings() returned ok.
The race window is really small but can be exploited if, for example,
thread B is interrupted or preempted after initializing uid_keyring, but
before doing setting session_keyring.
This couldn't be reproduced on a stock kernel. However, after placing
systemtap probe on 'user->session_keyring = session_keyring;' that
introduced some delay, the kernel could be crashed reliably.
Fix this by checking both pointers before deciding whether to return.
Alternatively, the test could be done away with entirely as it is checked
inside the mutex - but since the mutex is global, that may not be the best
way.
Signed-off-by: David Howells <dhowells@redhat.com> Reported-by: Mateusz Guzik <mguzik@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Morris <james.l.morris@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
return > 0 in case of success, so they will cause smsc95xx_suspend()
to return > 0 and cause suspend failure.
The bug is introduced in commit 3b9f7d(smsc95xx: fix error handling
in suspend failure case).
Signed-off-by: Ming Lei <ming.lei@canonical.com> Cc: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fengguang Wu run kernel build test to platform-drivers-x86/linux-next git tree
on x86_64 architecture and found a warning that was introduced by 727651bf738b6b917335025d09323d0962eda114 commit:
drivers/platform/x86/acer-wmi.c: In function â\80\98WMID_set_capabilitiesâ\80\99:
drivers/platform/x86/acer-wmi.c:1211: warning: â\80\98devicesâ\80\99 may be used
uninitialized in this function
This patch fixes the above warning message.
Signed-off-by: Lee, Chun-Yi <jlee@suse.com> Cc: Carlos Corbacho <carlos@strangeworlds.co.uk> Cc: Matthew Garrett <mjg@redhat.com> Cc: Dmitry Torokhov <dtor@mail.ru> Cc: Corentin Chary <corentincj@iksaif.net> Cc: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com> Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Three errors resulting in kernel memory disclosure:
1/ The structures used for the netlink based crypto algorithm report API
are located on the stack. As snprintf() does not fill the remainder of
the buffer with null bytes, those stack bytes will be disclosed to users
of the API. Switch to strncpy() to fix this.
2/ crypto_report_one() does not initialize all field of struct
crypto_user_alg. Fix this to fix the heap info leak.
3/ For the module name we should copy only as many bytes as
module_name() returns -- not as much as the destination buffer could
hold. But the current code does not and therefore copies random data
from behind the end of the module name, as the module name is always
shorter than CRYPTO_MAX_ALG_NAME.
Also switch to use strncpy() to copy the algorithm's name and
driver_name. They are strings, after all.
Realtek card reader supports both SD and MS card. According to the
settings of rtsx MFD driver, SD host will be probed before MS host.
If we boot/reboot Linux with SD card inserted, the resetting flow of SD
card will succeed, and the following resetting flow of MS is sure to fail.
Then MS upper-level driver will ask rtsx driver to turn power off. This
request leads to the result that the following SD commands fail and SD card
can't be accessed again.
In this commit, Realtek's SD and MS host driver will check whether the card
that upper driver requesting is the one existing in the slot. If not, Realtek's
host driver will refuse the operation to make sure the exlusive accessing
at the same time.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Cc: Tim Gardner <rtg.canonical@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Schedule card detect work at the end of the ISR
2. Callback function ops->cd_deglitch may delay for a period of time.
It is not proper to call this callback when local irq disabled.
3. Card detect flow can't be executed in parallel with other card reader
operations, so it's better to be protected by mutex.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Cc: Tim Gardner <rtg.canonical@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The physical memory fixmapped for the pvclock clock_gettime vsyscall
was allocated, and thus is not a kernel symbol. __pa() is the proper
method to use in this case.
Fixes the crash below when booting a next-20130204+ smp guest on a
3.8-rc5+ KVM host.
I noticed we were getting lots of warnings with xfstest 83 because we have
reservations outstanding. This is because we moved the orphan add outside
of the truncate, but we don't actually cleanup our reservation if something
fails. This fixes the problem and I no longer see warnings. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave sent me a panic where we were doing the orphan cleanup and panic'ed
trying to release our reservation from the orphan block rsv. The reason for
this is because our orphan block rsv had been free'd out from underneath us
because the transaction commit found that there were no orphan inodes
according to its count and decided to free it. This is incorrect so make
sure we inc the orphan inodes count so the accounting is all done properly.
This would also cause the warning in the orphan commit code normally if you
had any orphans to cleanup as they would only decrement the orphan count so
you'd get a negative orphan count which could cause problems during runtime.
Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hid_output_raw_report() makes a direct call to usb_control_msg(). However,
some USB3 boards have shown that the usb device is not ready during the
.probe(). This blocks the entire usb device, and the paired mice, keyboards
are not functional. The dmesg output is the following:
[ 11.912287] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-2/input2
[ 11.912537] logitech-djreceiver 0003:046D:C52B.0003: logi_dj_probe:logi_dj_recv_query_paired_devices error:-32
[ 11.912636] logitech-djreceiver: probe of 0003:046D:C52B.0003 failed with error -32
Relying on the scheduled call to usbhid_submit_report() fixes the problem.
related bugs:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1072082
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1039143
https://bugzilla.redhat.com/show_bug.cgi?id=840391
https://bugzilla.kernel.org/show_bug.cgi?id=49781
Reported-and-tested-by: Bob Bowles <bobjohnbowles@gmail.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By historical accident we have been reading trying to set new->user_ns
from new->user_ns. Which is totally silly as new->user_ns is NULL (as
is every other field in new except session_keyring at that point).
The intent is clearly to copy all of the fields from old to new so copy
old->user_ns into into new->user_ns.
Reported-by: Dave Jones <davej@redhat.com> Tested-by: Dave Jones <davej@redhat.com> Acked-by: Serge Hallyn <serge.hallyn@canonical.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stricter validation was introduced with commit da27a24383b2b
("efivarfs: guid part of filenames are case-insensitive") and commit 47f531e8ba3b ("efivarfs: Validate filenames much more aggressively"),
which is necessary for the guid portion of efivarfs filenames, but we
don't need to be so strict with the first part, the variable name. The
UEFI specification doesn't impose any constraints on variable names
other than they be a NULL-terminated string.
The above commits caused a regression that resulted in users seeing
the following message,
$ sudo mount -v /sys/firmware/efi/efivars mount: Cannot allocate memory
whenever pstore EFI variables were present in the variable store,
since their variable names failed to pass the following check,
/* GUID should be right after the first '-' */
if (s - 1 != strchr(str, '-'))
as a typical pstore filename is of the form, dump-type0-10-1-<guid>.
The fix is trivial since the guid portion of the filename is GUID_LEN
bytes, we can use (len - GUID_LEN) to ensure the '-' character is
where we expect it to be.
(The bogus ENOMEM error value will be fixed in a separate patch.)
Reported-by: Joseph Yasi <joe.yasi@gmail.com> Tested-by: Joseph Yasi <joe.yasi@gmail.com> Reported-by: Lingzhu Xiang <lxiang@redhat.com> Cc: Josh Boyer <jwboyer@redhat.com> Cc: Jeremy Kerr <jk@ozlabs.org> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f4a46d1f46a8fece34edd2023e054072b02e110d introduced a bug where
the ifconfig stats would remain 0 for phylib devices. This is due to
tp->link_up flag never becoming true causing tg3_periodic_fetch_stats()
to return.
The link_up flag was being updated in tg3_test_and_report_link_chg()
after setting up the phy. This function however, is not called for
phylib devices since the driver does not do the phy setup.
This patch moves the link_up flag update into the common
tg3_link_report() function that gets called for phylib devices as well
for non phylib devices when the link state changes.
To avoid updating link_up twice, we replace tg3_carrier_...() calls that
are followed by tg3_link_report(), with netif_carrier_...(). We can then
remove the unused tg3_carrier_on() function.
Reported-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes redundant and unbalanced pci_disable_device() from
__e1000_shutdown(). pci_clear_master() is enough, device can go into
suspended state with elevated enable_cnt.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org> Cc: Bruce Allan <bruce.w.allan@intel.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Borislav Petkov <bp@suse.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some mlme work structs are not cancelled on disassociation
nor interface deletion, which leads to them running after
the memory has been freed
There is not a clean way to cancel these in the disassociation
logic because they must be canceled outside of the ifmgd->mtx
lock, so just cancel them in mgd_stop logic that tears down
the station.
This fixes the crashes we see in 3.7.9+. The crash stack
trace itself isn't so helpful, but this warning gives
more useful info:
WARNING: at /home/greearb/git/linux-3.7.dev.y/lib/debugobjects.c:261 debug_print_object+0x7c/0x8d()
ODEBUG: free active (active state 0) object type: work_struct hint: ieee80211_sta_monitor_work+0x0/0x14 [mac80211]
Modules linked in: [...]
Pid: 14743, comm: iw Tainted: G C O 3.7.9+ #11
Call Trace:
[<ffffffff81087ef8>] warn_slowpath_common+0x80/0x98
[<ffffffff81087fa4>] warn_slowpath_fmt+0x41/0x43
[<ffffffff812a2608>] debug_print_object+0x7c/0x8d
[<ffffffff812a2bca>] debug_check_no_obj_freed+0x95/0x1c3
[<ffffffff8114cc69>] slab_free_hook+0x70/0x79
[<ffffffff8114ea3e>] kfree+0x62/0xb7
[<ffffffff8149f465>] netdev_release+0x39/0x3e
[<ffffffff8136ad67>] device_release+0x52/0x8a
[<ffffffff812937db>] kobject_release+0x121/0x158
[<ffffffff81293612>] kobject_put+0x4c/0x50
[<ffffffff8148f0d7>] netdev_run_todo+0x25c/0x27e
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6133705494bb introduced a circular lock dependency because
posix_cpu_timers_exit() is called by release_task(), which is holding
a writer lock on tasklist_lock, and this can cause a deadlock since
kill_fasync() gets called with nonblocking_pool.lock taken.
There's no reason why kill_fasync() needs to be taken while the random
pool is locked, so move it out to fix this locking dependency.
sys_llseek should specify the high and low 32-bit seek values as "unsigned
int" but instead it specifies "unsigned long". Since compat syscall
arguments are always sign-extended on tile, this means that a seek value
of 0xffffffff will be incorrectly interpreted as a value of -1ULL.
To avoid the risk of breaking binary compatibility on architectures
that already use sys_llseek this way, we follow the same path as MIPS
and provide a wrapper override.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update proc_ns_follow_link to use nd_jump_link instead of just
manually updating nd.path.dentry.
This fixes the BUG_ON(nd->inode != parent->d_inode) reported by Dave
Jones and reproduced trivially with mkdir /proc/self/ns/uts/a.
Sigh it looks like the VFS change to require use of nd_jump_link
happend while proc_ns_follow_link was baking and since the common case
of proc_ns_follow_link continued to work without problems the need for
making this change was overlooked.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a value of a vmaster slave control is changed, the ctl change
notification is sometimes ignored. This happens when the master
control overrides, e.g. when the corresponding master control is
muted. The reason is that slave_put() returns the value of the actual
slave put callback, and it doesn't reflect the virtual slave value
change.
This patch fixes the function just to return 1 whenever a slave value
is changed.
Commit 9f9c9cbb6057 ("drivers/firmware/dmi_scan.c: fetch dmi version
from SMBIOS if it exists") hoisted the check for "_DMI_" into
dmi_scan_machine(), which means that we don't bother to check for
"_DMI_" at offset 16 in an SMBIOS entry. smbios_present() may also call
dmi_present() for an address where we found "_SM_", if it failed further
validation.
Check for "_DMI_" in smbios_present() before calling dmi_present().
[akpm@linux-foundation.org: fix build] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Reported-by: Tim McGrath <tmhikaru@gmail.com> Tested-by: Tim Mcgrath <tmhikaru@gmail.com> Cc: Zhenzhong Duan <zhenzhong.duan@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When MSG_COPY is set, a duplicate message must be allocated for the copy
before locking the queue. However, the copy could not be larger than was
sent which is limited to msg_ctlmax.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Acked-by: Stanislav Kinsbursky <skinsbursky@parallels.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need it to restore the ilk rc6 context, since the gpu wait no
requires interrupts. But in general having interrupts around should
help in code sanity, since more and more stuff is interrupt driven.
drm/i915: Rearrange code to only have a single method for waiting upon the ring
Like in the driver load code we need to make sure that hotplug
interrupts don't cause havoc with our modeset state, hence block them
with the existing infrastructure. Again we ignore races where we might
loose hotplug interrupts ...
Note that the driver load part of the regression has already been
fixed in
drm/i915: reorder setup sequence to have irqs for output setup
v2: Add a note to the commit message about which patch fixed the
driver load part of the regression. Stable kernels need to backport
both patches.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=54691 Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Reported-and-Tested-by: Ilya Tumaykin <itumaykin@gmail.com> Reviewed-by: Chris wilson <chris@chris-wilson.co.uk> (v1) Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise the new&shiny irq-driven gmbus and dp aux code won't work that
well. Noticed since the dp aux code doesn't have an automatic fallback
with a timeout (since the hw provides for that already).
v2: Simple move drm_irq_install before intel_modeset_gem_init, as
suggested by Ben Widawsky.
v3: Now that interrupts are enabled before all connectors are fully
set up, we might fall over serving a HPD interrupt while things are
still being set up. Instead of jumping through massive hoops and
complicating the code with a separate hpd irq enable step, simply
block out the hotplug work item from doing anything until things are
in place.
v4: Actually, we can enable hotplug processing only after the fbdev is
fully set up, since we call down into the fbdev from the hotplug work
functions. So stick the hpd enabling right next to the poll helper
initialization.
v5: We need to enable irqs before intel_modeset_init, since that
function sets up the outputs.
v6: Fixup cleanup sequence, too.
Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log