Fast Channel Change across bands was enabled for
AR9462 recently, but this is causing baseband issues.
Disable it until this feature is tested well. Also,
remove the feature bit for AR9565 since it is
a single-band card and doesn't support this feature.
Cc: stable@vger.kernel.org Reported-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Accessing the current channel definition in mac80211
when processing RX packets is problematic because it
could have been updated when a scan is issued. Since a
channel change involves flushing the existing packets
in the RX queue before a chip-reset is done, they would
be processed using the wrong band/channel information.
To avoid this, use the current channel information
maintained in the driver.
Cc: stable@vger.kernel.org Reported-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bing Zhao [Wed, 8 Jan 2014 23:45:56 +0000 (15:45 -0800)]
mwifiex: fix potential buffer overflow in dt configuration
If cfgdata length exceeds the command buffer size we will end up
getting buffer overflow problem. Fix it by checking the buffer
size less the command header length.
Reviewed-by: Paul Stewart <pstew@chromium.org> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
As soon as skb is ready to be reaped, prefetch 1-st cache line.
This accelerates data access that is performed later, during the
packet classification by the driver and IP stack.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use hardware capabilities to limit IRQ generation to about 15 per msec
It corresponds to about 7 packets/IRQ when running iperf with default
parameters at 1.3Gbps
Do not enable this feature in the sniffer (monitor) mode, because
interrupt moderation cause timestamp accuracy deterioration.
For the sniffer flow, it is important to get precise timestamp.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Machek [Tue, 7 Jan 2014 12:13:28 +0000 (13:13 +0100)]
wl1251: fix NULL pointer dereference
wl1251: fix NULL pointer dereference
Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Reported-by: Felipe Contreras <felipe.contreras@gmail.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Gnedt [Tue, 7 Jan 2014 12:11:27 +0000 (13:11 +0100)]
wl1251: enforce changed hw encryption support on monitor state change
The firmware doesn't support per packet encryption selection, so disable hw
encryption support completely while a monitor interface is present to support
injection of packets (which shouldn't get encrypted by hw).
To enforce the changed hw encryption support force a disassociation on
non-monitor interfaces.
For disassociation a workaround using hw connection monitor is employed,
which temporary enables hw connection manager flag.
Signed-off-by: David Gnedt <david.gnedt@davizone.at> Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Gnedt [Tue, 7 Jan 2014 12:10:51 +0000 (13:10 +0100)]
wl1251: disable retry and ACK policy for injected packets
Set the retry limit to 0 and disable the ACK policy for injected packets.
Signed-off-by: David Gnedt <david.gnedt@davizone.at> Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Gnedt [Tue, 7 Jan 2014 12:10:14 +0000 (13:10 +0100)]
wl1251: enable tx path in monitor mode if necessary for packet injection
If necessary enable the tx path in monitor mode for packet injection using
the JOIN command with BSS_TYPE_STA_BSS and zero BSSID.
Signed-off-by: David Gnedt <david.gnedt@davizone.at> Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Gnedt [Tue, 7 Jan 2014 12:09:42 +0000 (13:09 +0100)]
wl1251: fix channel switching in monitor mode
Use the ENABLE_RX command for channel switching when no interface is present
(monitor mode only).
The advantage of ENABLE_RX is that it leaves the tx data path disabled in
firmware, whereas the usual JOIN command seems to transmit some frames at
firmware level.
Signed-off-by: David Gnedt <david.gnedt@davizone.at> Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Gnedt [Tue, 7 Jan 2014 12:09:06 +0000 (13:09 +0100)]
wl1251: disable power saving in monitor mode
Force power saving off while monitor interface is present.
Signed-off-by: David Gnedt <david.gnedt@davizone.at> Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Port multicast address filtering from wl1271 driver.
It sets up the hardware multicast address filter in configure_filter() with
addresses supplied through prepare_multicast().
Signed-off-by: David Gnedt <david.gnedt@davizone.at> Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Gnedt [Tue, 7 Jan 2014 12:07:52 +0000 (13:07 +0100)]
wl1251: configure hardware en-/decryption for monitor mode
Disable hardware encryption (DF_ENCRYPTION_DISABLE) and decryption
(DF_SNIFF_MODE_ENABLE) via wl1251_acx_feature_cfg while monitor interface is
present.
Signed-off-by: David Gnedt <david.gnedt@davizone.at> Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Gnedt [Tue, 7 Jan 2014 12:06:58 +0000 (13:06 +0100)]
wl1251: split RX and TX data path initialisation
Split up data path initialisation into RX and TX data path initialisation
functions. This change is required for channel switching in monitor mode.
Signed-off-by: David Gnedt <david.gnedt@davizone.at> Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Gnedt [Tue, 7 Jan 2014 12:06:24 +0000 (13:06 +0100)]
wl1251: implement hardware ARP filtering
Update hardware ARP filter configuration on BSS_CHANGED_ARP_FILTER
notification from mac80211.
Ported from wl1271 driver.
Signed-off-by: David Gnedt <david.gnedt@davizone.at> Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Gnedt [Tue, 7 Jan 2014 12:05:45 +0000 (13:05 +0100)]
wl1251: retry power save entry
Port of the power save entry retry code from wl1251 driver version included
in the Maemo Fremantle kernel.
This tries to enable power save mode up to 3 times before failing.
Signed-off-by: David Gnedt <david.gnedt@davizone.at> Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Gnedt [Tue, 7 Jan 2014 12:04:53 +0000 (13:04 +0100)]
wl1251: fix scan behaviour while not associated
With a dissasociated card I often encoutered very long scan delays.
My guess is that it has something to do with the cards DTIM handling and
another firmware bug mentioned in the TI WLAN driver, which is described as
the card may never end scanning if the channel is overloaded because it
can't send probe requests. I think the firmware somehow also tries to
receive DTIM messages when the BSSID is not set. Therefore most of the time
it waits for DTIM messages and can't do scanning work.
Anyway we can workaround this misbehaviour by setting the HIGH_PRIORITY
bit for scans in disassociated state.
Signed-off-by: David Gnedt <david.gnedt@davizone.at> Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the Bluetooth Low Energy Address type checking when
setting Universal/Local bit for the 6loWPAN network device or for the
peer device connection.
ADDR_LE_DEV_PUBLIC or ADDR_LE_DEV_RANDOM are the values allowed for
"src_type" and "dst_type" in the hci_conn struct. The Bluetooth link
type can be obtainned reading the "type" field in the same struct.
Bluetooth: Always wait for a connection on RFCOMM open()
This patch fixes two regressions introduced with the recent rfcomm tty
rework.
The current code uses the carrier_raised() method to wait for the
bluetooth connection when a process opens the tty.
However processes may open the port with the O_NONBLOCK flag or set the
CLOCAL termios flag: in these cases the open() syscall returns
immediately without waiting for the bluetooth connection to
complete.
This behaviour confuses userspace which expects an established bluetooth
connection.
The patch restores the old behaviour by waiting for the connection in
rfcomm_dev_activate() and removes carrier_raised() from the tty_port ops.
As a side effect the new code also fixes the case in which the rfcomm
tty device is created with the flag RFCOMM_REUSE_DLC: the old code
didn't call device_move() and ModemManager skipped the detection
probe. Now device_move() is always called inside rfcomm_dev_activate().
Bluetooth: Release RFCOMM port when the last user closes the TTY
This patch fixes a userspace regression introduced by the commit 29cd718b.
If the rfcomm device was created with the flag RFCOMM_RELEASE_ONHUP the
user space expects that the tty_port is released as soon as the last
process closes the tty.
The current code attempts to release the port in the function
rfcomm_dev_state_change(). However it won't get a reference to the
relevant tty to send a HUP: at that point the tty is already destroyed
and therefore NULL.
This patch fixes the regression by taking over the tty refcount in the
tty install method(). This way the tty_port is automatically released as
soon as the tty is destroyed.
As a consequence the check for RFCOMM_RELEASE_ONHUP flag in the hangup()
method is now redundant. Instead we have to be careful with the reference
counting in the rfcomm_release_dev() function.
brcmfmac: use custom destructor callback for all netdevice interfaces
The destructor for net devices was set to free_netdev() to get rid
of it and the private data. The private data refers to a brcmf_if
instance, but indirectly it also refers to brcmf_cfg80211_vif which
holds the wdev. This is freed as well by using a new custom destructor
called brcmf_cfg80211_free_netdev().
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: call brcmf_cfg80211_detach() after removal of interfaces
Instead of calling brcmf_cfg80211_detach() in brcmf_del_if() when
deleting the primary interface, call it in brcmf_detach() after
deleting all interfaces.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: move wiphy_unregister() call to brcmf_cfg80211_detach()
The wiphy_unregister() call was done in brcmf_free_vif() when the
last interface was being removed. This is not the obvious place to
do that. This patch moves it to the brcmf_cfg80211_detach(). This
removes the need to keep count of interfaces.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: inform cfg80211 when changing the CONNECTED state
Upon unload of the brcmfmac driver it gave a kernel warning because
cfg80211 still believed to be connected to an AP. The brcmfmac had
already transitioned to disconnected state during unload. This patch
adds informing cfg80211 about this transition. This will get rid of
warning from cfg80211 seen upon module unload:
brcmfmac: only disable clock when brcmf_sdio_bus_init() fails
The condition to disable the clock at the end of brcmf_sdio_bus_init()
was wrong as the bus state is updated by the calling function. Hence,
the clock was always disabled after brcmf_sdio_bus_init() which was
not the intended behaviour.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: enable watchdog when bus initialization is complete
Change condition in brcmf_sdio_wd_timer() function to program
watchdog only when in BRCMF_BUS_DATA state. This avoids watchdog
being active during initialization. During initialization the
SDIO save&restore capability is determined which affect the
bus sleep mechanism used in watchdog thread.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: correct detection of save&restore device capability
The detection of the save&restore capability in brcmf_sdio_sr_capable()
is only valid for certain chipsets. This patch should cover it for all
chipsets currently supported.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: correct reporting HT40 support in wiphy htcap
Using 'iw phy' only showed HT20 support in the HT capabilities info.
This patch determines support for HT40 using a firmware query that
is supposed to work for all supported devices.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: cleanup helper functions in sdio remove path
Two helper functions in the sdio remove path were very thin and
only used once. So its code is moved to the calling function.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Mon, 6 Jan 2014 11:40:38 +0000 (12:40 +0100)]
brcmfmac: Limit control message length from host to device.
An control request or set message length is restricted to
ETH frame length for the buffer from host to device. This
is limitation is imposed by the firmware.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Mon, 6 Jan 2014 11:40:37 +0000 (12:40 +0100)]
brcmfmac: Remove some obsolete definitions and variables.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johan Hedberg [Mon, 6 Jan 2014 16:27:02 +0000 (18:27 +0200)]
Bluetooth: Default to no security with L2CAP RAW sockets
L2CAP RAW sockets can be used for things which do not involve
establishing actual connection oriented L2CAP channels. One example of
such usage is the l2ping tool. The default security level for L2CAP
sockets is LOW, which implies that for SSP based connection
authentication is still requested (although with no MITM requirement),
which is not what we want (or need) for things like l2ping. Therefore,
default to one lower level, i.e. BT_SECURITY_SDP, for L2CAP RAW sockets
in order not to trigger unwanted authentication requests.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Mon, 6 Jan 2014 16:27:01 +0000 (18:27 +0200)]
Bluetooth: Fix NULL pointer dereference when disconnecting
When disconnecting it is possible that the l2cap_conn pointer is already
NULL when bt_6lowpan_del_conn() is entered. Looking at l2cap_conn_del
also verifies this as there's a NULL check there too. This patch adds
the missing NULL check without which the following bug may occur:
Marcel Holtmann [Fri, 3 Jan 2014 11:02:36 +0000 (03:02 -0800)]
Bluetooth: Deal with USB devices that are faking CSR vendor
There exists a set of Bluetooth USB devices that show up on the USB
bus as 0a12:0001 and identify themselves as devices from CSR. However
they are not. When sending Read Local Version command they now have
a split personality and say they are from Broadcom.
< HCI Command: Read Local Version Information (0x04|0x0001) plen 0
> HCI Event: Command Complete (0x0e) plen 12
Read Local Version Information (0x04|0x0001) ncmd 1
status 0x00
HCI Version: 2.0 (0x3) HCI Revision: 0x3000
LMP Version: 2.0 (0x3) LMP Subversion: 0x420b
Manufacturer: Broadcom Corporation (15)
The assumption is that they are neither CSR nor Broadcom based devices
and that they are designed and manufactured by someone else.
For the most parts they follow the Bluetooth HCI specification and
can be used as standard Bluetooth devices. However they have the
minor problem that the Delete Stored Link Key command is not working
as it should.
During the Bluetooth controller setup, this command is needed if
stored link keys are supported. For these devices it has to be
assumed that this is broken and so just set a quirk to clearly
indicate the behavior. After that the setup can just proceed.
Now the trick part is to detect these faulty devices since we do
not want to punish all CSR and all Broadcom devices. The original
devices do actually work according to the specification.
What is known so far is that these broken devices set the USB bcdDevice
revision information to 1.0 or less.
In case of CSR devices, the bcdDevice revision contains the firmware
build ID and that is normally a higher value. If the bcdDevice revision
is 1.0 or less, then an extra setup stage is checking if Read Local
Version returns CSR manufacturer information. If not then it will be
assumed that this is a broken device and the Delete Stored Link Key
command will be marked as broken.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Fri, 3 Jan 2014 11:02:35 +0000 (03:02 -0800)]
Bluetooth: Add quirk for disabling Delete Stored Link Key command
Some controller pretend they support the Delete Stored Link Key command,
but in reality they really don't support it.
< HCI Command: Delete Stored Link Key (0x03|0x0012) plen 7
bdaddr 00:00:00:00:00:00 all 1
> HCI Event: Command Complete (0x0e) plen 4
Delete Stored Link Key (0x03|0x0012) ncmd 1
status 0x11 deleted 0
Error: Unsupported Feature or Parameter Value
Not correctly supporting this command causes the controller setup to
fail and will make a device not work. However sending the command for
controller that handle stored link keys is important. This quirk
allows a driver to disable the command if it knows that this command
handling is broken.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Paul Gortmaker [Thu, 2 Jan 2014 23:58:32 +0000 (18:58 -0500)]
wireless: delete non-required instances of include <linux/init.h>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Thu, 2 Jan 2014 18:31:37 +0000 (19:31 +0100)]
ssb: fix sparse warnings in driver_chipcommon_sflash.c
CHECK drivers/ssb/driver_chipcommon_sflash.c
drivers/ssb/driver_chipcommon_sflash.c:40:11: warning: Using plain integer as NULL pointer
drivers/ssb/driver_chipcommon_sflash.c:58:11: warning: Using plain integer as NULL pointer
drivers/ssb/driver_chipcommon_sflash.c:69:11: warning: Using plain integer as NULL pointer
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Thu, 2 Jan 2014 18:31:36 +0000 (19:31 +0100)]
bcma: fix sparse warnings in driver_chipcommon_sflash.c
CHECK drivers/bcma/driver_chipcommon_sflash.c
drivers/bcma/driver_chipcommon_sflash.c:41:11: warning: Using plain integer as NULL pointer
drivers/bcma/driver_chipcommon_sflash.c:59:11: warning: Using plain integer as NULL pointer
drivers/bcma/driver_chipcommon_sflash.c:70:11: warning: Using plain integer as NULL pointer
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The maximum permissible values for noise floor in ETSI
and Japan domains have been updated with new EU
regulations for CCA detection. Adjust the values in the
driver accordingly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Mon, 30 Dec 2013 18:15:07 +0000 (19:15 +0100)]
carl9170: use ether_addr_equal_64bits
Ether_addr_equal_64bits is more efficient than ether_addr_equal, and can be
used when each argument is an array within a structure that contains at
least two bytes of data beyond the array.
The structures involved are:
ieee80211_hdr defined in include/linux/ieee80211.h,
ieee80211_bar defined in include/linux/ieee80211.h and
ath_common defined in drivers/net/wireless/ath/ath.h
This was done using Coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Mon, 30 Dec 2013 18:15:06 +0000 (19:15 +0100)]
at76c50x-usb: use ether_addr_equal_64bits
Ether_addr_equal_64bits is more efficient than ether_addr_equal, and can be
used when each argument is an array within a structure that contains at
least two bytes of data beyond the array.
The structures involved are:
at76_priv defined in drivers/net/wireless/at76c50x-usb.h and
ieee80211_mgmt defined in include/linux/ieee80211.h
This was done using Coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Mon, 30 Dec 2013 18:15:05 +0000 (19:15 +0100)]
ipw2x00: use ether_addr_equal_64bits
Ether_addr_equal_64bits is more efficient than ether_addr_equal, and can be
used when each argument is an array within a structure that contains at
least two bytes of data beyond the array.
The structure involved is
libipw_network defined in drivers/net/wireless/ipw2x00/libipw.h
This was done using Coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Mon, 30 Dec 2013 18:15:04 +0000 (19:15 +0100)]
ath9k: use ether_addr_equal_64bits
Ether_addr_equal_64bits is more efficient than ether_addr_equal, and can be
used when each argument is an array within a structure that contains at
least two bytes of data beyond the array.
The structures involved are:
ieee80211_hdr defined in include/linux/ieee80211.h
ath_common defined in drivers/net/wireless/ath/ath.h
This was done using Coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Mon, 30 Dec 2013 18:15:03 +0000 (19:15 +0100)]
iwlegacy: use ether_addr_equal_64bits
Ether_addr_equal_64bits is more efficient than ether_addr_equal, and can be
used when each argument is an array within a structure that contains at
least two bytes of data beyond the array.
The structures involved are:
ieee80211_hdr defined in include/linux/ieee80211.h,
il_priv defined in drivers/net/wireless/iwlegacy/common.h and
il_rxon_cmd defined in drivers/net/wireless/iwlegacy/commands.h
This was done using Coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Mon, 30 Dec 2013 18:15:02 +0000 (19:15 +0100)]
rtlwifi: use ether_addr_equal_64bits
Ether_addr_equal_64bits is more efficient than ether_addr_equal, and can be
used when each argument is an array within a structure that contains at
least two bytes of data beyond the array.
The structures involved are:
ieee80211_hdr defined in include/linux/ieee80211.h and
rtl_mac defined in drivers/net/wireless/rtlwifi/wifi.h
This was done using Coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Mon, 30 Dec 2013 18:15:01 +0000 (19:15 +0100)]
mwl8k: use ether_addr_equal_64bits
Ether_addr_equal_64bits is more efficient than ether_addr_equal, and can be
used when each argument is an array within a structure that contains at
least two bytes of data beyond the array.
The structures involved are:
ieee80211_hdr defined in include/linux/ieee80211.h and
mwl8k_priv defined in drivers/net/wireless/mwl8k.c
This was done using Coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Mon, 30 Dec 2013 18:14:59 +0000 (19:14 +0100)]
p54: use ether_addr_equal_64bits
Ether_addr_equal_64bits is more efficient than ether_addr_equal, and can be
used when each argument is an array within a structure that contains at
least two bytes of data beyond the array.
The structures involved are:
ieee80211_hdr defined in include/linux/ieee80211.h and
p54_common defined in drivers/net/wireless/p54/p54.h
This was done using Coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Mon, 30 Dec 2013 18:14:58 +0000 (19:14 +0100)]
ath5k: use ether_addr_equal_64bits
Ether_addr_equal_64bits is more efficient than ether_addr_equal, and can be
used when each argument is an array within a structure that contains at
least two bytes of data beyond the array.
The structures involved are:
ieee80211_mgmt defined in include/linux/ieee80211.h and
ath_common defined in drivers/net/wireless/ath/ath.h
This was done using Coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Mon, 30 Dec 2013 18:14:57 +0000 (19:14 +0100)]
rt2x00: use ether_addr_equal_64bits
Ether_addr_equal_64bits is more efficient than ether_addr_equal, and can be
used when each argument is an array within a structure that contains at
least two bytes of data beyond the array.
The structures involved are:
ieee80211_bar defined in include/linux/ieee80211.h and
rt2x00_bar_list_entry defined in drivers/net/wireless/rt2x00/rt2x00.h.
This was done using Coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Sat, 28 Dec 2013 04:17:15 +0000 (09:47 +0530)]
ath9k: Fix interrupt statistics
Initialize "sync_cause" to zero since commit
"ath9k: move ath9k_debug_sync_cause out of ath9k_hw"
fills it conditionally based on ISR status.
Not doing this results in garbage values in debugfs.
Cc: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Tue, 24 Dec 2013 05:14:25 +0000 (10:44 +0530)]
ath9k: Remove RX Poll
This patch removes the convoluted and hacky method of
monitoring for connectivity. We rely on mac80211's connection
loss logic and doing it in the driver is not necessary.
The HW check for MAC/BB hangs is also simplified, there
is no need to have a separate work instance for it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Tue, 24 Dec 2013 05:14:23 +0000 (10:44 +0530)]
ath9k: Identify baseband watchdog signatures
A full HW reset is not required for all baseband watchdog
signatures. Some BB watchdog updates are benign and can
be discarded, some require re-programming of certain registers
and others require a chip reset.
This patch adds a routine to identify such signatures.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Tue, 24 Dec 2013 05:14:21 +0000 (10:44 +0530)]
ath9k: Fix PHY restart workaround
The PHY restart workaround that handles baseband hangs
for packets with unsupported rates is required only
for a HW bug in AR9300 v2.2. All the subsequent chips in
the AR9003 family do not require this driver fix since
it has been addressed in the HW.
Since the value of the AR_PHY_RESTART register is written
with the default initvals, make sure that PHY restart is
always disabled once this particular BB hang signaure has
been encountered.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Tue, 24 Dec 2013 05:14:20 +0000 (10:44 +0530)]
ath9k: Fix MAC HW hang check for AR9003
The current method of identifying MAC hangs is
convoluted and also, the signatures are wrong and
don't apply to all the chips in the AR9003 family.
Fix this by cleaning up the code and checking for
the correct hang signatures.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Tue, 24 Dec 2013 05:14:17 +0000 (10:44 +0530)]
ath9k: Fix max AMPDU size calculation
The maximum A-MPDU size is calculated in ath_tx_aggr_start(),
so there is no need to do it in node_attach() too. Also, make
sure that the correct size is calculated as described in
8.4.2.58.3.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Josh Triplett [Mon, 23 Dec 2013 21:55:03 +0000 (13:55 -0800)]
net: wireless: brcm80211: Drop debug version with build date/time
The kernel already has this information, and individual drivers
shouldn't duplicate that. This also eliminates the use of __DATE__ and
__TIME__, which make the build non-deterministic.
Signed-off-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wenliang Fan [Wed, 18 Dec 2013 05:56:12 +0000 (13:56 +0800)]
drivers/net/wireless/hostap: Integer overflow
The local variable 'value' comes from 'extra', a parameter of function
'prism2_ioctl_priv_prism2_param'. If a large number passed to 'value',
there would be an integer overflow in the following line:
local->passive_scan_timer.expires = jiffies +
local->passive_scan_interval * HZ
Signed-off-by: Wenliang Fan <fanwlexca@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ilan Peer [Mon, 23 Dec 2013 20:18:02 +0000 (22:18 +0200)]
iwlwifi: mvm: dynamically update tsf_id
Currently, the MAC context tsf_id assignment and the master/slave
relations are determined only when a new vif is added, as part
of the MAC context resource allocation. However, at this stage, the
beacon interval is not known, and thus could not be taken into account
in the master-slave algorithm.
To fix this, recalculate the MAC context tsf_id assignment,
just before the MAC context is activated, i.e., just before
a station VMAC is configured to associated and before an AP
VMAC is started.
Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
projects / karo-tx-linux.git / log