This device is not using the proper demod IF. Instead of using the
IF macro, it is specifying a IF frequency. This doesn't work, as xc3028
needs to load an specific SCODE for the tuner. In this case, there's
no IF table for 5 MHz.
This patch protects the I2C buffer access in order to manage concurrent
access. This protection is done using mutex.
Furthermore, for the dib9000, if a pid filtering command is
received during the tuning, this pid filtering command is delayed to
avoid any concurrent access issue.
If the bus has been reset on resume, set the alternate setting to 0.
This should be the default value, but some devices crash or otherwise
misbehave if they don't receive a SET_INTERFACE request before any other
video control request.
Microdia's 0c45:6437 camera has been found to require this change or it
will stop sending video data after resume.
uvc_video.c]
Signed-off-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds checks for minimum and maximum pitch size to prevent
invalid settings which could otherwise crash the machine. Also the
alignment is done in a slightly more readable way.
As Laurent pointed out we must not use any information in the passed
var besides xoffset, yoffset and vmode as otherwise applications
might abuse it. Also use the aligned fix.line_length and not the
(possible) unaligned xres_virtual.
Following on Herton's patch "fb: avoid possible deadlock caused by
fb_set_suspend" which moves lock_fb_info() out of fb_set_suspend()
to its callers, correct sh-mobile's locking around call to
fb_set_suspend() and the same sort of deaklocks with console_lock()
due to order of taking the lock.
console_lock() must be taken while fb_info is already locked and fb_info
must be locked while calling fb_set_suspend().
A lock ordering issue can cause deadlocks: in framebuffer/console code,
all needed struct fb_info locks are taken before acquire_console_sem(),
in places which need to take console semaphore.
But fb_set_suspend is always called with console semaphore held, and
inside it we call lock_fb_info which gets the fb_info lock, inverse
locking order of what the rest of the code does. This causes a real
deadlock issue, when we write to state fb sysfs attribute (which calls
fb_set_suspend) while a framebuffer is being unregistered by
remove_conflicting_framebuffers, as can be shown by following show
blocked state trace on a test program which loads i915 and runs another
forked processes writing to state attribute:
fb-test2 which reproduces above is available on kernel.org bug #26232.
To solve this issue, avoid calling lock_fb_info inside fb_set_suspend,
and move it out to where needed (callers of fb_set_suspend must call
lock_fb_info before if needed). So far, the only place which needs to
call lock_fb_info is store_fbstate, all other places which calls
fb_set_suspend are suspend/resume hooks that should not need the lock as
they should be run only when processes are already frozen in
suspend/resume.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Sebastian Siewior <bigeasy@linutronix.de> Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Put sysfs attributes of ccwgroup devices in an attribute group to
ensure that these attributes are actually present when userspace
is notified via uevents.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The rcu page table free code uses a couple of bits in the page table
pointer passed to tlb_remove_table to discern the different page table
types. __tlb_remove_table extracts the type with an incorrect mask which
leads to memory leaks. The correct mask is ((FRAG_MASK << 4) | FRAG_MASK).
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
git commit 5e9a2692 "[S390] ptrace cleanup" introduced a regression
for the case when both a user PER set (e.g. a storage alteration trace) and
PTRACE_SINGLESTEP are active. The new code will overrule the user PER set
with a instruction-fetch PER set over the whole address space for ptrace
single stepping. The inferior process will be stopped after each instruction
with an instruction fetch event. Any other events that may have occurred
concurrently are not reported (e.g. storage alteration event) because the
control bits for them are not set. The solution is to merge the PER control
bits of the user PER set with the PER_EVENT_IFETCH control bit for
PTRACE_SINGLESTEP.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Susan Gao <sgao@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmico.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ak4535_reg should be 8bit, but cache table is defined as 16bit.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to the datasheet:
Format Control (05h)
BITS[3:2]
FMT[1:0] Audio data format selection
00 = right justified mode
01 = left justified mode
10 = I2S mode
11 = DSP mode
BIT[4] LRP Polarity selec for LRCLK/DSP mode select
0 = normal LRCLK poalrity/DSP mode A
1 = inverted LRCLK poarity/DSP mode B
For SND_SOC_DAIFMT_DSP_A, we should set 0x000C instead of 0x0003.
For SND_SOC_DAIFMT_DSP_B, we should set 0x001C instead of 0x0013.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reported-by: Chris Paulson-Ellis <chris@edesix.com> Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For the !HAVE_ATOMIC_IOMAP case the stub functions did not call
pagefault_disable/_enable. The i915 driver relies on the map
actually being atomic, otherwise it can deadlock with it's own
pagefault handler in the gtt pwrite fastpath.
This is exercised by gem_mmap_gtt from the intel-gpu-toosl gem
testsuite.
v2: Chris Wilson noted the lack of an include.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38115 Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
nfsiostat was failing to find mounted filesystems on kernels after
2.6.38 because of changes to show_vfsstat() by commit c7f404b40a3665d9f4e9a927cc5c1ee0479ed8f9. This patch adds back the
"device" tag before the nfs server entry so scripts can parse the
mountstats file correctly.
- nfs4_file_downgrade() doesn't remove the BOTH access bit on
downgrade, so the server's idea of the stateid's access gets
out of sync with the client's. If we want to keep an O_RDWR
open in this case, we should do that in the file_put_access
logic rather than here.
- We forgot to convert v4 access to an open mode here.
This logic has proven too hard to get right. In the future we may
consider:
- reexamining the lock/openowner relationship (locks probably
don't really need to take their own references here).
- adding open upgrade/downgrade support to the vfs.
- removing the atomic operations. They're redundant as long as
this is all under some other lock.
Also, maybe some kind of additional static checking would help catch
O_/NFS4_SHARE_ACCESS confusion.
Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A client that wants to execute a file must be able to read it. Read
opens over nfs are therefore implicitly allowed for executable files
even when those files are not readable.
NFSv2/v3 get this right by using a passed-in NFSD_MAY_OWNER_OVERRIDE on
read requests, but NFSv4 has gotten this wrong ever since dc730e173785e29b297aa605786c94adaffe2544 "nfsd4: fix owner-override on
open", when we realized that the file owner shouldn't override
permissions on non-reclaim NFSv4 opens.
So we can't use NFSD_MAY_OWNER_OVERRIDE to tell nfsd_permission to allow
reads of executable files.
So, do the same thing we do whenever we encounter another weird NFS
permission nit: define yet another NFSD_MAY_* flag.
The industry's future standardization on 128-bit processors will be
motivated primarily by the need for integers with enough bits for all
the NFSD_MAY_* flags.
Reported-by: Leonardo Borda <leonardoborda@gmail.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The server is returning nfserr_resource for both permanent errors and
for errors (like allocation failures) that might be resolved by retrying
later. Save nfserr_resource for the former and use delay/jukebox for
the latter.
Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fan Yong <yong.fan@whamcloud.com> noticed setting
FMODE_32bithash wouldn't work with nfsd v4, as
nfsd4_readdir() checks for 32 bit cookies. However, according to RFC 3530
cookies have a 64 bit type and cookies are also defined as u64 in
'struct nfsd4_readdir'. So remove the test for >32-bit values.
Signed-off-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
nfs_find_and_lock_request will take a reference to the nfs_page and
will then put it if the req is already locked. It's possible though
that the reference will be the last one. That put then can kick off
a whole series of reference puts:
nfs_page
nfs_open_context
dentry
inode
If the inode ends up being deleted, then the VFS will call
truncate_inode_pages. That function will try to take the page lock, but
it was already locked when migrate_page was called. The code
deadlocks.
Fix this by simply refusing the migration request if PagePrivate is
already set, indicating that the page is already associated with an
active read or write request.
We've had a customer test a backported version of this patch and
the preliminary results seem good.
Cc: Andrea Arcangeli <aarcange@redhat.com> Reported-by: Harshula Jayasuriya <harshula@redhat.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a mechanism to resume selected IRQs during syscore_resume
instead of dpm_resume_noirq.
Under Xen we need to resume IRQs associated with IPIs early enough
that the resched IPI is unmasked and we can therefore schedule
ourselves out of the stop_machine where the suspend/resume takes
place.
This issue was introduced by 676dc3cf5bc3 "xen: Use IRQF_FORCE_RESUME".
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com> Cc: xen-devel <xen-devel@lists.xensource.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Link: http://lkml.kernel.org/r/1318713254.11016.52.camel@dagon.hellion.org.uk Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The trace_pipe_raw handler holds a cached page from the time the file
is opened to the time it is closed. The cached page is used to handle
the case of the user space buffer being smaller than what was read from
the ring buffer. The left over buffer is held in the cache so that the
next read will continue where the data left off.
After EOF is returned (no more data in the buffer), the index of
the cached page is set to zero. If a user app reads the page again
after EOF, the check in the buffer will see that the cached page
is less than page size and will return the cached page again. This
will cause reading the trace_pipe_raw again after EOF to return
duplicate data, making the output look like the time went backwards
but instead data is just repeated.
The fix is to not reset the index right after all data is read
from the cache, but to reset it after all data is read and more
data exists in the ring buffer.
Reported-by: Jeremy Eder <jeder@redhat.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a small window of time between when a device fails and when
it is removed from the array. During this time we might still read
from it, but we won't write to it - so it is possible that we could
read stale data.
We didn't need the test of 'Faulty' before because the test on
In_sync is sufficient. Since we started allowing reads from the early
part of non-In_sync devices we need a test on Faulty too.
This is suitable for any kernel from 2.6.36 onwards, though the patch
might need a bit of tweaking in 3.0 and earlier.
These warnings (generally one per CPU) are a result of
initializing x86_cpu_to_logical_apicid while apic_default is
still in use, but the check in setup_local_APIC() being done
when apic_bigsmp was already used as an override in
default_setup_apic_routing():
Overriding APIC driver with bigsmp
Enabling APIC mode: Physflat. Using 5 I/O APICs
------------[ cut here ]------------
WARNING: at .../arch/x86/kernel/apic/apic.c:1239
...
CPU 1 irqstacks, hard=f1c9a000 soft=f1c9c000
Booting Node 0, Processors #1
smpboot cpu 1: start_ip = 9e000
Initializing CPU#1
------------[ cut here ]------------
WARNING: at .../arch/x86/kernel/apic/apic.c:1239
setup_local_APIC+0x137/0x46b() Hardware name: ...
CPU1 logical APIC ID: 2 != 8
...
Fix this (for the time being, i.e. until
x86_32_early_logical_apicid() will get removed again, as Tejun
says ought to be possible) by overriding the previously stored
values at the point where the APIC driver gets overridden.
v2: Move this and the pre-existing override logic into
arch/x86/kernel/apic/bigsmp_32.c.
The parameter's origin type is long. On an i386 architecture, it can
easily be larger than 0x80000000, causing this function to convert it
to a sign-extended u64 type.
Change the type to unsigned long so we get the correct result.
Signed-off-by: hank <pyu@redhat.com> Cc: John Stultz <john.stultz@linaro.org>
[ build fix ] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We were using incorrect max and min dwell times during forced passive
scans because we were still using the active scan states to scan
(passively) the channels that were not marked as passive.
Instead of doing passive scans in active states, we now skip active
states and scan for all channels in passive states.
were designed to allow timestamping in PHY devices. The first
function, called during the MAC driver's hard_xmit method, identifies
PTP protocol packets, clones them, and gives them to the PHY device
driver. The PHY driver may hold onto the packet and deliver it at a
later time using the second function, which adds the packet to the
socket's error queue.
As pointed out by Johannes, nothing prevents the socket from
disappearing while the cloned packet is sitting in the PHY driver
awaiting a timestamp. This patch fixes the issue by taking a reference
on the socket for each such packet. In addition, the comments
regarding the usage of these function are expanded to highlight the
rule that PHY drivers must use skb_complete_tx_timestamp() to release
the packet, in order to release the socket reference, too.
These functions first appeared in v2.6.36.
Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Richard Cochran <richard.cochran@omicron.at> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When I introduced in-kernel off-channel TX I
introduced a bug -- the work can't be canceled
again because the code clear the skb pointer.
Fix this by keeping track separately of whether
TX status has already been reported.
Reported-by: Jouni Malinen <j@w1.fi> Tested-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the PHY should disappear (for example, on an USB Ethernet MAC), then
the driver would leak any undelivered time stamp packets. This commit
fixes the issue by calling the appropriate functions to free any packets
left in the transmit and receive queues.
The driver first appeared in v3.0.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Renato Westphal noticed that since commit a2835763e130c343ace5320c20d33c281e7097b7
"rtnetlink: handle rtnl_link netlink notifications manually" was merged
we no longer send a netlink message when a networking device is moved
from one network namespace to another.
Fix this by adding the missing manual notification in dev_change_net_namespaces.
Since all network devices that are processed by dev_change_net_namspaces are
in the initialized state the complicated tests that guard the manual
rtmsg_ifinfo calls in rollback_registered and register_netdevice are
unnecessary and we can just perform a plain notification.
Tested-by: Renato Westphal <renatowestphal@gmail.com> Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With help from Tejun, the problem is found to be caused by 32bit PIO
mode, so introduce the quirk patch to disable 32bit PIO on SATA piix
for some Sandybridge CPT chipsets.
Seth also tested the patch on all five affected chipsets
(pci device ID: 0x1c00, 0x1c01, 0x1d00, 0x1e00, 0x1e01), and found
the patch does fix the problem.
Tested-by: Heasley, Seth <seth.heasley@intel.com> Cc: Alan Cox <alan@linux.intel.com> Signed-off-by: Ming Lei <ming.lei@canonical.com> Acked-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 420e3646 allowed the kernel to reduce the number of unnecessary
commit calls by skipping the commit when there are a large number of
outstanding pages.
However, the current test in nfs_commit_unstable_pages does not handle
the edge condition properly. When ncommit == 0, then that means that the
kernel doesn't need to do anything more for the inode. The current test
though in the WB_SYNC_NONE case will return true, and the inode will end
up being marked dirty. Once that happens the inode will never be clean
until there's a WB_SYNC_ALL flush.
Fix this by immediately returning from nfs_commit_unstable_pages when
ncommit == 0.
Mike noticed this problem initially in RHEL5 (2.6.18-based kernel) which
has a backported version of 420e3646. The inode cache there was growing
very large. The inode cache was unable to be shrunk since the inodes
were all marked dirty. Calling sync() would essentially "fix" the
problem -- the WB_SYNC_ALL flush would result in the inodes all being
marked clean.
What I'm not clear on is how big a problem this is in mainline kernels
as the writeback code there is very different. Either way, it seems
incorrect to re-mark the inode dirty in this case.
Reported-by: Mike McLean <mikem@redhat.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The reverted commit was rendered obsolete by a VFS fix: commit 5547e8aac6f71505d621a612de2fca0dd988b439 (writeback: Update dirty flags in
two steps). We now no longer need to worry about writeback_single_inode()
missing our marking the inode for COMMIT in 'do_writepages()' call.
Reverting this patch, fixes a performance regression in which the inode
would continuously get queued to the dirty list, causing the writeback
code to unnecessarily try to send a COMMIT.
Due to post-increment in condition of kmod_loop_msg in __request_module(),
the system log can be spammed by much more than 5 instances of the 'runaway
loop' message if the number of events triggering it makes the kmod_loop_msg
to overflow.
Fix that by making sure we never increment it past the threshold.
The min_brightness value of the sabi_config is incorrectly used in brightness
calculations. For the config where min_brightness = 1 and max_brightness = 8,
the user visible range should be 0 to 7 with hardware being set in the range
of 1 to 8. What is actually happening is that the user visible range is 0 to
8 with hardware being set in the range of -1 to 7.
This patch fixes the above issue as well as a miscalculation that would occur
in the case of min_brightness > 1.
Signed-off-by: Jason Stubbs <jasonbstubbs@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Matthew Garrett <mjg@redhat.com>
The caif code will register its own pernet_operations, and then register
a netdevice_notifier. Each time the netdevice_notifier is triggered,
it'll do some stuff... including a lookup of its own pernet stuff with
net_generic().
If the net_generic() call ever returns NULL, the caif code will BUG().
That doesn't seem *so* unreasonable, I suppose — it does seem like it
should never happen.
However, it *does* happen. When we clone a network namespace,
setup_net() runs through all the pernet_operations one at a time. It
gets to loopback before it gets to caif. And loopback_net_init()
registers a netdevice... while caif hasn't been initialised. So the caif
netdevice notifier triggers, and immediately goes BUG().
We could imagine a complex and overengineered solution to this generic
class of problems, but this patch takes the simple approach. It just
makes caif_device_notify() *not* go looking for its pernet data
structures if the device it's being notified about isn't a caif device
in the first place.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Acked-by: Sjur Brændeland <sjur.brandeland@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Propagate the baremetal git commit "swiotlb: fix wrong panic"
(fba99fa38b023224680308a482e12a0eca87e4e1) in the Xen-SWIOTLB version.
wherein swiotlb's map_page wrongly calls panic() when it can't find
a buffer fit for device's dma mask. It should return an error instead.
Devices with an odd dma mask (i.e. under 4G) like b44 network card hit
this bug (the system crashes):
With Xen changeset 23428 "libxl: Add 'e820_host' option to config file"
the E820 as seen from the host can now be passed into the guest.
This means that a PV guest can now:
- Use the correct PCI I/O gap. Before these patches, Linux guest would
boot up and would tell:
[ 0.000000] Allocating PCI resources starting at 40000000 (gap: 40000000:c0000000)
while in actuality the PCI I/O gap should have been:
[ 0.000000] Allocating PCI resources starting at b0000000 (gap: b0000000:4c000000)
- The PV domain with PCI devices was limited to 3GB. It now can be booted
with 4GB, 8GB, or whatever number you want. The PCI devices will now _not_ conflict
with System RAM. Meaning the drivers can load.
CC: Jesse Barnes <jbarnes@virtuousgeek.org> CC: linux-pci@vger.kernel.org
[v2: Made the string less broken up. Suggested by Joe Perches] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The stable@kernel.org email address has been replaced with the
stable@vger.kernel.org mailing list. Change the stable kernel rules to
reference the new list instead of the semi-defunct email alias.
PHY errors relevant for ANI are always tracked by hardware counters, the
bits that allow them to pass through the rx filter are independent of that.
Enabling PHY errors in the rx filter often creates lots of useless DMA traffic
and might be responsible for some of the rx dma stop failure warnings.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch fixes the assumption of maximum number of GPIO pins present
in AR9287/AR9300. this fix is essential as we might encounter some
functionality issues involved in accessing the status of GPIO pins which
are all incorrectly assumed to be not within the range of max_num_gpio
of AR9300/AR9287 chipsets
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was reported and tested by Martin Walter over at AVM GmbH Berlin.
This also applies to 3.0.1 so sendint to stable.
Cc: s.kirste@avm.de Cc: d.friedel@avm.de Cc: Martin Walter <m.walter@avm.de> Cc: Peter Grabienski <pgrabien@qca.qualcomm.com> Tested-by: Martin Walter <m.walter@avm.de> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Do the magnitude/phase coeff correction only if the outlier
is detected. Updating wrong magnitude/phase coeff factor
impacts not only tx gain setting but also leads to poor
performance in congested networks. In the clear environment
the impact is very minimal because the outlier happens
very rarely according to the past experiment. It occured
less than once every 1000 calibrations.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Qualcomm ate up Atheros, all of the old e-mail addresses
no longer work and e-mails sent to it will bounce. Update
the addresses to the new shiny Qualcomm Atheros (QCA) ones.
Cc: stable@kernel.org Cc: netdev@vger.kernel.org Cc: jouni@qca.qualcomm.com Cc: yangjie@qca.qualcomm.com Cc: vthiagar@qca.qualcomm.com Cc: senthilb@qca.qualcomm.com Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
IDs found in the Windows driver's ZTEusbnet.inf file from the
ZTE MF100 drivers (O2 UK). Also fixes the ZTE MF626 device
since it really is distinct from the 4G Systems stick and
apparently needs the net interface blacklisted too, while
there's no indication (yet) that the 4G Systems stick does.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's cleaner than the array stuff, and we're about to add a bunch
more blacklist entries. Second, there are devices that need both
the sendsetup and the reserved interface blacklists, which the
current code can't accommodate.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some Stellaris evaluation kits have the JTAG/SWD FTDI chip onboard,
and some, like EK-LM3S9B90, come with a separate In-Circuit Debugger
Interface Board. The ICDI board can also be used stand-alone, for
other boards and chips than the kit it came with. The ICDI has both
old style 20-pin JTAG connector and new style JTAG/SWD 10-pin 1.27mm
pitch connector.
Tested with EK-LM3S9B90, where the BD-ICDI board is included.
Signed-off-by: Peter Stuge <peter@stuge.se> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add vendor and product ID for the SMART USB to serial adapter. These
were meant to be used with their SMART Board whiteboards, but can be
re-purposed for other tasks. Tested and working (at at least 9600 bps).
Signed-off-by: Eric Benoit <eric@ecks.ca> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new runtime PM code has shown that many webcams suffer
from a race condition that may crash them upon resume.
Runtime PM is especially prone to show the problem because
it retains power to the cameras at all times. However
system suspension may also crash the devices and retain
power to the devices.
The only way to solve this problem without races is in
usbcore with the RESET_RESUME quirk.
Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern points out that after spin_unlock(&ps->lock) there is no
guarantee that ps->pid won't be freed. Since kill_pid_info_as_uid() is
called after the spin_unlock(), the pid passed to it must be pinned.
In the usb printer class specific request get_device_id the value of
wIndex is (interface << 8 | altsetting) instead of just interface.
This enables the detection of some printers with libusb.
At least some OHCI hardware (such as the MCP89) fails to flag any change
in the host status register or the port status registers when receiving
a remote wakeup while in D3 state. This results in the controller being
resumed but no device state change being noticed, at which point the
controller is put back to sleep again. Since there doesn't seem to be any
reliable way to identify the state change, just unconditionally resume the
hub. It'll be put back to sleep in the near future anyway if there are no
active devices attached to it.
Signed-off-by: Matthew Garrett <mjg@redhat.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch solves two things:
1) Enables autosense emulation code to correctly
interpret descriptor format sense data, and
2) Fixes a bug whereby the autosense emulation
code would overwrite descriptor format sense data
with SENSE KEY HARDWARE ERROR in fixed format, to
incorrectly look like this:
Oct 21 14:11:07 localhost kernel: sd 7:0:0:0: [sdc] Sense Key : Recovered Error [current] [descriptor]
Oct 21 14:11:07 localhost kernel: Descriptor sense data with sense descriptors (in hex):
Oct 21 14:11:07 localhost kernel: 72 01 04 1d 00 00 00 0e 09 0c 00 00 00 00 00 00
Oct 21 14:11:07 localhost kernel: 00 4f 00 c2 00 50
Oct 21 14:11:07 localhost kernel: sd 7:0:0:0: [sdc] ASC=0x4 ASCQ=0x1d
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Depending on the implementation of the hardware blinking function in
blink_set(), the led can support hardware blinking for some values of
delay_on and delay_off and fall-back to software blinking for some other
values.
Turning off the blink_timer unconditionally before starting to blink
make sure that a sequence like:
OFF
hardware blinking
software blinking
hardware blinking
does not leave the software blinking timer active.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Cc: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
epoll can acquire recursively acquire ep->mtx on multiple "struct
eventpoll"s at once in the case where one epoll fd is monitoring another
epoll fd. This is perfectly OK, since we're careful about the lock
ordering, but it causes spurious lockdep warnings. Annotate the recursion
using mutex_lock_nested, and add a comment explaining the nesting rules
for good measure.
Recent versions of systemd are triggering this, and it can also be
demonstrated with the following trivial test program:
--------------------8<--------------------
int main(void) {
int e1, e2;
struct epoll_event evt = {
.events = EPOLLIN
};
When compiling an i386_defconfig kernel with gcc-4.6.1-9.fc15.i686, I
noticed a warning about the asm operand for test_bit in kprobes'
can_boost. I discovered that this caused only the first long of
twobyte_is_boostable[] to be output.
Jakub filed and fixed gcc PR50571 to correct the warning and this output
issue. But to solve it for less current gcc, we can make kprobes'
twobyte_is_boostable[] non-const, and it won't be optimized out.
Before:
CC arch/x86/kernel/kprobes.o
In file included from include/linux/bitops.h:22:0,
from include/linux/kernel.h:17,
from [...]/arch/x86/include/asm/percpu.h:44,
from [...]/arch/x86/include/asm/current.h:5,
from [...]/arch/x86/include/asm/processor.h:15,
from [...]/arch/x86/include/asm/atomic.h:6,
from include/linux/atomic.h:4,
from include/linux/mutex.h:18,
from include/linux/notifier.h:13,
from include/linux/kprobes.h:34,
from arch/x86/kernel/kprobes.c:43:
[...]/arch/x86/include/asm/bitops.h: In function ‘can_boost.part.1’:
[...]/arch/x86/include/asm/bitops.h:319:2: warning: use of memory input
without lvalue in asm operand 1 is deprecated [enabled by default]
This is a workaround for a UV2 hub bug that affects the format of system
global addresses.
The GRU API for UV2 was inadvertently broken by a hardware change. The
format of the physical address used for TLB dropins and for addresses used
with instructions running in unmapped mode has changed. This change was
not documented and became apparent only when diags failed running on
system simulators.
For UV1, TLB and GRU instruction physical addresses are identical to
socket physical addresses (although high NASID bits must be OR'ed into the
address).
For UV2, socket physical addresses need to be converted. The NODE portion
of the physical address needs to be shifted so that the low bit is in bit
39 or bit 40, depending on an MMR value.
It is not yet clear if this bug will be fixed in a silicon respin. If it
is fixed, the hub revision will be incremented & the workaround disabled.
Signed-off-by: Jack Steiner <steiner@sgi.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: "H. Peter Anvin" <hpa@zytor.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a bug with the handling of REPORT TARGET PORT GROUPS
containing a smaller allocation length than the payload requires causing
memory writes beyond the end of the buffer. This patch checks for the
minimum 4 byte length for the response payload length, and also checks
upon each loop of T10_ALUA(su_dev)->tg_pt_gps_list to ensure the Target
port group and Target port descriptor list is able to fit into the
remaining allocation length.
If the response payload exceeds the allocation length length, then rd_len
is still increments to indicate to the initiator that the payload has
been truncated.
Reported-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The purpose of this patch is to remove a section of "bad" code that
assigns the last DAC to ports E or F in order to support notebooks
with docking in earlier days, around ALSA 1.0.19 - 21. This is not
necessary now and actually breaks some configurations that use these
ports as other devices. This have been tested on several different
configurations to make sure that it is working for different combinations.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Besides being unnecessary, it is too small (currently truncates
responses to 60 bytes). The mid-layer will have already allocated a
sufficiently sized buffer, just kmap and copy into it directly.
Reported-by: Derick Marks <derick.w.marks@intel.com> Tested-by: Derick Marks <derick.w.marks@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During kdump testing I noticed timeouts when initialising each IPR
adapter. While the driver has logic to detect an adapter in an
indeterminate state, it wasn't triggering and each adapter went
through a 5 minute timeout before finally going operational.
Some analysis showed the needs_hard_reset flag wasn't getting set.
We can check the reset_devices kernel parameter which is set by
kdump and force a full reset. This fixes the problem.
Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch for megaraid_sas will fix a potential bad pointer access
in megasas_reset_timer(), when a MegaRAID 9265/9285 or 9360/9380 gets a
timeout. megasas_build_io_fusion() sets SCp.ptr to be a struct
megasas_cmd_fusion *, but then megasas_reset_timer() was casting SCp.ptr to be
a struct megasas_cmd *, then trying to access cmd->instance, which is invalid.
Just loading instance from scmd->device->host->hostdata in
megasas_reset_timer() fixes the issue.
Signed-off-by: Adam Radford <aradford@gmail.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 15bed0f2f added a quirk for the e823 Ricoh card reader to lower the
base frequency. However, the quirk first checks to see if the proprietary
MMC controller is disabled, and returns if so. On some devices, such as the
Lenovo X220, the MMC controller is already disabled by firmware it seems,
but the frequency change is still needed so sdhci-pci can talk to the cards.
Since the MMC controller is disabled, the frequency fixup was never being run
on these machines.
This moves the e823 check above the MMC controller check so that it always
gets run.
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=722509
f39b2dd9d ("mmc: core: Bus width testing needs to handle suspend/resume")
added code to only compare read-only ext_csd fields in bus width testing
code, yet it's comparing some fields that are never set.
The affected fields are ext_csd.raw_erased_mem_count and
ext_csd.raw_partition_support.
Signed-off-by: Andrei Warkentin <andrey.warkentin@gmail.com> Acked-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During a rescan operation mmc_attach(sd|mmc|sdio) functions are
called. The error handling in these function can trigger a detach
of the bus, which also meant a power off. This is not notified by
the rescan operation which then continues to the next attach function.
If a power off has been done, the framework must never send any
new commands to the host driver, without first doing a new power up.
This will most likely trigger any host driver to hang.
Moving power off out of detach and instead handle power off
separately when it is actually needed, solves the issue.
Commit 9b9fe724 accidentally used RADEON_GPIO_EN_* where
RADEON_GPIO_MASK_* was intended. This caused improper initialization
of I2C buses, mostly visible when setting i2c_algo_bit.bit_test=1.
Using the right constants fixes the problem.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Cc: Jerome Glisse <j.glisse@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When force == false, we don't do load detection in the connector
detect functions. Unforunately, we also return the previous
connector state so we never get disconnect events for DVI-I, DVI-A,
or VGA. Save whether we detected the monitor via load detection
previously and use that to determine whether we return the previous
state or not.
DVI-D and HDMI-A are digital only, so there's no need to
attempt analog load detect. Also, skip bail before the
!force check, or we fail to get a disconnect events.
The next patches in the series attempt to fix disconnect
events for connectors with analog support (DVI-I, HDMI-B,
DVI-A).
projects / karo-tx-linux.git / log