David S. Miller [Thu, 11 Jun 2015 05:49:49 +0000 (22:49 -0700)]
Merge tag 'mac80211-next-for-davem-2015-06-10' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For this round we mostly have fixes:
* mesh fixes from Alexis Green and Chun-Yeow Yeoh,
* a documentation fix from Jakub Kicinski,
* a missing channel release (from Michal Kazior),
* a fix for a signal strength reporting bug (from Sara Sharon),
* handle deauth while associating (myself),
* don't report mangled TX SKB back to userspace for status (myself),
* handle aggregation session timeouts properly in fast-xmit (myself)
However, there are also a few cleanups and one big change that
affects all drivers (and that required me to pull in your tree)
to change the mac80211 HW flags to use an unsigned long bitmap
so that we can extend them more easily - we're running out of
flags even with a cleanup to remove the two unused ones.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Smalley [Wed, 10 Jun 2015 12:44:59 +0000 (08:44 -0400)]
net/unix: support SCM_SECURITY for stream sockets
SCM_SECURITY was originally only implemented for datagram sockets,
not for stream sockets. However, SCM_CREDENTIALS is supported on
Unix stream sockets. For consistency, implement Unix stream support
for SCM_SECURITY as well. Also clean up the existing code and get
rid of the superfluous UNIXSID macro.
Motivated by https://bugzilla.redhat.com/show_bug.cgi?id=1224211,
where systemd was using SCM_CREDENTIALS and assumed wrongly that
SCM_SECURITY was also supported on Unix stream sockets.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov> Acked-by: Paul Moore <paul@paul-moore.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 10 Jun 2015 01:15:23 +0000 (18:15 -0700)]
Add support of Cavium Liquidio ethernet adapters
Following patch V8 adds support for Cavium Liquidio pci express
based 10Gig ethernet adapters.
1) Consolidated all debug macros to either call dev_* or
netdev_* macros directly, feedback from previous patch.
2) Changed soft commands to avoid crash when running
in interrupt context.
3) Fixed link status not reflecting correct status when NetworkManager
is running. Added MODULE_FIRMWARE declarations.
Following were the previous patches.
Patch V7:
1) Minor comments from v6 release regarding debug statements.
2) Fix for large multicast lists.
3) Fixed lockup issue if port initialization fails.
4) Enabled MSI by default.
https://patchwork.ozlabs.org/patch/464441/
Patch V6:
1) Addressed the uint64 vs u64 issue, feedback from previous patch.
2) Consolidated some receive processing routines.
3) Removed link status polling method.
https://patchwork.ozlabs.org/patch/459514/
Patch V5:
Based on the feedback from earlier patches with regards to
consolidation of common functions like device init, register
programming for cn66xx and cn68xx devices.
https://patchwork.ozlabs.org/patch/438979/
Patch V4:
Following were the changes based on the feedback from earlier patch:
1) Added mmiowb while synchronizing queue updates and other hw
interactions.
2) Statistics will now be incremented non-atomically per each ring.
liquidio_get_stats will add stats of each ring while reporting the
total statistics counts.
3) Modified liquidio_ioctl to return proper return codes.
4) Modified device naming to use standard Ethernet naming.
5) Global function names in the driver will have lio_/liquidio_/octeon_
prefix.
6) Ethtool related changes for:
Removed redundant stats and jiffies.
Use default ethtool handler of link status.
Speed setting will make use of ethtool_cmd_speed_set.
7) Added checks for pci_map_* return codes.
8) Check for signals while waiting in interruptible mode
https://patchwork.ozlabs.org/patch/435073/
Patch v3:
Implemented feedback from previous patch like:
Removed NAPI Config and DEBUG config options, added BQL and xmit_more
support.
https://patchwork.ozlabs.org/patch/422749/
Patch V2:
Implemented feedback from previous patch.
https://patchwork.ozlabs.org/patch/413539/
First Patch:
https://patchwork.ozlabs.org/patch/412946/
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com> Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com> Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com> Signed-off-by: Robert Richter <Robert.Richter@caviumnetworks.com> Signed-off-by: Aleksey Makarov <Aleksey.Makarov@caviumnetworks.com> Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 11 Jun 2015 05:14:14 +0000 (22:14 -0700)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-06-09
This series contains updates to ixgbe only.
The series adds additional support for x550 support, such as WoL and
auto-negotiation of flow control. Adds new PHY support (external PHY)
for x550, as well as the new methods/functions needed to support the new
PHY's. Fixed a bug found in code inspection, where a check was missed
when clearing counters for x550. Also fixed the init code flow for copper
x550 devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 11 Jun 2015 05:00:27 +0000 (22:00 -0700)]
Merge branch 'cxgb4-next'
Hariprasad Shenai says:
====================
Add cim_ma_la, cim_pif_la and tx_rate debugfs entry
This patch series adds the following.
Add debugfs entry to dump CIM MA logic analyzer and CIM PIF logic analyzer logs.
Also adds support to dump tx rate of the channels in the adapter
This patch series has been created against net-next tree and includes
patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge: make br_fdb_delete also check if the port matches
Before this patch the user-specified bridge port was ignored when
deleting an fdb entry and thus one could delete an entry that belonged
to any port.
Example (eth0 and eth1 are br0 ports):
bridge fdb add 00:11:22:33:44:55 dev eth0 master
bridge fdb del 00:11:22:33:44:55 dev eth1 master
(succeeds)
after the patch:
bridge fdb add 00:11:22:33:44:55 dev eth0 master
bridge fdb del 00:11:22:33:44:55 dev eth1 master
RTNETLINK answers: No such file or directory
Based on a patch by Wilson Kok.
Reported-by: Wilson Kok <wkok@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
this is a pull request of a two patches for net-next.
The first patch is by Tomas Krcka, he fixes the (currently unused)
register address for acceptance filters. Oliver Hartkopp contributes a
patch for the cangw, where an optional UID is added to reference
routing jobs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 2 Jun 2015 19:39:54 +0000 (21:39 +0200)]
mac80211: convert HW flags to unsigned long bitmap
As we're running out of hardware capability flags pretty quickly,
convert them to use the regular test_bit() style unsigned long
bitmaps.
This introduces a number of helper functions/macros to set and to
test the bits, along with new debugfs code.
The occurrences of an explicit __clear_bit() are intentional, the
drivers were never supposed to change their supported bits on the
fly. We should investigate changing this to be a per-frame flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Alexis Green [Tue, 9 Jun 2015 23:20:24 +0000 (16:20 -0700)]
mac80211: Fix a case of incorrect metric used when forwarding a PREQ
This patch fixes a bug in hwmp_preq_frame_process where the wrong metric
can be used when forwarding a PREQ. This happens because the code uses
the same metric variable to record the value of the metric to the source
of the PREQ and the value of the metric to the target of the PREQ.
This comes into play when both reply and forward are set which happens
when IEEE80211_PREQ_PROACTIVE_PREP_FLAG is set and when MP_F_DO | MP_F_RF
is set. The original code had a special case to handle the first case
but not the second.
The patch uses distinct variables for the two metrics which makes the
code flow much clearer and removes the need to restore the original
value of metric when forwarding.
Signed-off-by: Alexis Green <agreen@cococorp.com> CC: Jesse Jones <jjones@cococorp.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
David S. Miller [Wed, 10 Jun 2015 03:23:52 +0000 (20:23 -0700)]
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
Included changes:
- use common Jenkins hash instead of private implementation
- extend internal routing API
- properly re-arrange header files inclusion
- clarify precedence between '&' and '?'
- remove unused ethhdr variable in batadv_gw_dhcp_recipient_get()
- ensure per-VLAN structs are updated upon MAC change
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Don Skidmore [Wed, 10 Jun 2015 00:48:54 +0000 (17:48 -0700)]
ixgbe: Set lan_id before using I2C
We need to call the set_lan_id before accessing I2C and this wasn't
being done so this patch corrects that. Likewise we do the same for
QSFP just to be consistent.
In the X550 case this is even more important as with out it the mux
is not controlled properly.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Wed, 10 Jun 2015 00:44:58 +0000 (17:44 -0700)]
ixgbe: add link check for X550 copper
This patch adds ixgbe_check_link_t_X550em for checking copper PHY
link. We check that both the MAC and external PHY have link. This
is to avoid a false link up between the internal and external PHY
when the external PHY doesn't have link.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Wed, 10 Jun 2015 00:36:53 +0000 (17:36 -0700)]
ixgbe: fix X550 PHY function pointers
A subset of the X550 function pointers didn't have default methods. This
didn't cause any issue with previous X550 devices as they were all
redefined. However future devices will need these default values.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Wed, 10 Jun 2015 00:02:35 +0000 (17:02 -0700)]
ixgbe: fix X550 devices init flow
Reviewing the X550 copper init flow with the Si team resulted in a
new simplified flow. We no longer wait for the PHY FW initialization
complete bit to be set as this bit is only set once by the PHY at power
on and then cleared on the first read. So only the first instance of
running SW (or possibly MAC FW) needs to initialize the PHY.
The PHY initialization has been simplified and now only requires that
the PHY FW be un-stalled
low-power mode or enabled the transceiver
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Tue, 9 Jun 2015 23:59:04 +0000 (16:59 -0700)]
ixgbe: fix issue with sfp events with new X550 devices
Add checks for systems that don't have SFP's to avoid incorrectly
acting on interrupts that are falsely interpreted as SFP events.
We do this by updating the ixgbe_is_sfp to be aware of the
new X550 devices. This also includes a modified check generating
the EICR mask to be more forward-looking.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Tue, 9 Jun 2015 23:52:02 +0000 (16:52 -0700)]
ixgbe: add support for interrupts from X550 external PHY
This patch adds support for receiving interrupts from a external copper
PHY for the X550 part. This includes enabling, detection as well as
re-enablement.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Tue, 9 Jun 2015 23:36:23 +0000 (16:36 -0700)]
ixgbe: Add const string for overheat message
The over heat message is displayed for multiple reasons but the text is
cut-n-pasted for each of these cases. This patch pulls the text from the
same location. I noticed this as I am about to add another case.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Tue, 9 Jun 2015 23:26:44 +0000 (16:26 -0700)]
ixgbe: add X550 support for external PHY and forced 1G/10G support
This patch adds x550 external PHY interrupt and forced 1G/10G support.
This included enabling and handling LSC and thermal sensor interrupt.
ixgbe_handle_lasi() has been added for handling the interrupts received
over SDP0 from the external 10baseT PHY. ixgbe_enable_lasi_ext_t_x550em
and ixgbe_get_lasi_ext_t_x550em have been added to X550em to enable
mask and check interrupt flags for the external PHY.
Forced 1G/10G link speed is handled via ixgbe_mac_link_t_X550em.
ixgbe_seupt_mac_link_t_X550em sets up the internal PHY and external PHY
to either iXFI (10G) or KX (1G) based on the user selected auto
advertised link speed setting. Then sets up the external PHY auto
advertised link speed.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Tue, 9 Jun 2015 23:18:56 +0000 (16:18 -0700)]
ixgbe: Restore ESDP settings after MAC reset
The I2C mux control relies on the SDP setting in the ESDP register
so it is necessary to restore the value after a MAC reset. Combine
all this functionality in to a support function.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Tue, 9 Jun 2015 23:09:47 +0000 (16:09 -0700)]
ixgbe: Add a PHY power state method
This new method will control the PHY power state. You pass in the
state you wish to change to (ether on or off). For cases where this
method is not used the current PHY power state behavior is maintained.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Tue, 9 Jun 2015 23:00:17 +0000 (16:00 -0700)]
ixgbe: add support for WoL and autoneg FC for some X550 devices
These Device ID could support both WoL and autoneg flow control. In
the case of WoL this is indicated by the eeprom. This patch enables
these devices this support.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Wed, 10 Jun 2015 00:15:01 +0000 (17:15 -0700)]
ixgbe: add array of MAC type dependent values
Some of the register addresses and format where unfortunately changed
between MAC types. To get around this we add a const u32 *mvals pointer
to the ixgbe_hw struct to point to an array of mac-type-dependent
values. These can include register offsets, masks, whatever can be in
a u32. When the ixgbe_hw struct is initialized, a pointer to the
appropriate array must be set.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexis Green [Tue, 9 Jun 2015 20:00:43 +0000 (13:00 -0700)]
mac80211: Always check rates and capabilities in mesh mode
In mesh mode there is a race between establishing links and processing
rates and capabilities in beacons. This is very noticeable with slow
beacons (e.g. beacon intervals of 1s) and manifested for us as stations
using minstrel when minstrel_ht should be used. Fixed by changing
mesh_sta_info_init so that it always checks rates and such if it has not
already done so.
Signed-off-by: Alexis Green <agreen@cococorp.com> CC: Jesse Jones <jjones@cococorp.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Alexis Green [Fri, 5 Jun 2015 19:43:54 +0000 (12:43 -0700)]
mac80211: Fix incorrectly named last_hop_metric variable in mesh_rx_path_sel_frame
The last hop metric should refer to link cost (this is how
hwmp_route_info_get uses it for example). But in mesh_rx_path_sel_frame
we are not dealing with link cost but with the total cost to the origin
of a PREQ or PREP.
Signed-off-by: Alexis Green <agreen@cococorp.com> CC: Jesse Jones <jjones@cococorp.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sara Sharon [Wed, 3 Jun 2015 07:44:17 +0000 (10:44 +0300)]
mac80211: ignore invalid scan RSSI values
Channels in 2.4GHz band overlap, this means that if we
send a probe request on channel 1 and then move to channel
2, we will hear the probe response on channel 2. In this
case, the RSSI will be lower than if we had heard it on
the channel on which it was sent (1 in this case).
The scan result ignores those invalid values and the
station last signal should not be updated as well.
In case the scan determines the signal to be invalid turn on
the flag so the station last signal will not be updated with
the value and thus user space probing for NL80211_STA_INFO_SIGNAL
and NL80211_STA_INFO_SIGNAL_AVG will not get this invalid RSSI
value.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 3 Jun 2015 06:36:13 +0000 (08:36 +0200)]
mac80211: release channel on auth failure
There were a few rare cases when upon
authentication failure channel wasn't released.
This could cause stale pointers to remain in
chanctx assigned_vifs after interface removal and
trigger general protection fault later.
This could be triggered, e.g. on ath10k with the
following steps:
1. start an AP
2. create 2 extra vifs on ath10k host
3. connect vif1 to the AP
4. connect vif2 to the AP
(auth fails because ath10k firmware isn't able
to maintain 2 peers with colliding AP mac
addresses across vifs and consequently
refuses sta_info_insert() in
ieee80211_prep_connection())
5. remove the 2 extra vifs
6. goto step 2; at step 3 kernel was crashing:
Johannes Berg [Tue, 9 Jun 2015 14:45:08 +0000 (16:45 +0200)]
mac80211: handle aggregation session timeout on fast-xmit path
The conversion to the fast-xmit path lost proper aggregation session
timeout handling - the last_tx wasn't set on that path and the timer
would therefore incorrectly tear down the session periodically (with
those drivers/rate control algorithms that have a timeout.)
In case of iwlwifi, this was every 5 seconds and caused significant
throughput degradation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Tue, 9 Jun 2015 06:05:10 +0000 (08:05 +0200)]
can: cangw: introduce optional uid to reference created routing jobs
Similar to referencing iptables rules by their line number this UID allows to
reference created routing jobs, e.g. to alter configured data modifications.
The UID is an optional non-zero value which can be provided at routing job
creation time. When the UID is set the UID replaces the data modification
configuration as job identification attribute e.g. at job removal time.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tomas Krcka [Sat, 30 May 2015 09:42:57 +0000 (11:42 +0200)]
can: mcp251x: use correct register address for acceptance filters
This patch corrects addresses of acceptance filters. These registers are not in
use, but values should be correct. Tested with MCP2515 and am3352 and also
checked datasheets for MCP2515 and MCP2510.
Signed-off-by: Tomas Krcka <tomas.krcka@nkgroup.cz> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
1) Fix stack allocation in s390 BPF JIT, from Michael Holzheu.
2) Disable LRO on openvswitch paths, from Jiri Benc.
3) UDP early demux doesn't handle multicast group membership properly,
fix from Shawn Bohrer.
4) Fix TX queue hang due to incorrect handling of mixed sized fragments
and linearlization in i40e driver, from Anjali Singhai Jain.
5) Cannot use disable_irq() in timer handler of AMD xgbe driver, from
Thomas Lendacky.
6) b2net driver improperly assumes pci_alloc_consistent() gives zero'd
out memory, use dma_zalloc_coherent(). From Sriharsha Basavapatna.
7) Fix use-after-free in MPLS and ipv6, from Robert Shearman.
8) Missing neif_napi_del() calls in cleanup paths of b44 driver, from
Hauke Mehrtens.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: replace last open coded skb_orphan_frags with function call
net: bcmgenet: power on MII block for all MII modes
ipv6: Fix protocol resubmission
ipv6: fix possible use after free of dev stats
b44: call netif_napi_del()
bridge: disable softirqs around br_fdb_update to avoid lockup
Revert "bridge: use _bh spinlock variant for br_fdb_update to avoid lockup"
mpls: fix possible use after free of device
be2net: Replace dma/pci_alloc_coherent() calls with dma_zalloc_coherent()
bridge: use _bh spinlock variant for br_fdb_update to avoid lockup
amd-xgbe: Use disable_irq_nosync from within timer function
rhashtable: add missing import <linux/export.h>
i40e: Make sure to be in VEB mode if SRIOV is enabled at probe
i40e: start up in VEPA mode by default
i40e/i40evf: Fix mixed size frags and linearization
ipv4/udp: Verify multicast group is ours in upd_v4_early_demux()
openvswitch: disable LRO
s390/bpf: fix bpf frame pointer setup
s390/bpf: fix stack allocation
Linus Torvalds [Mon, 8 Jun 2015 23:26:53 +0000 (16:26 -0700)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull last-minute virtio fix from Michael Tsirkin:
"This fixes a minor issue affecting multiqueue virtio net when user
keeps changing the number of active queues and CPUs are added and
removed by hotplug"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_pci: Clear stale cpumask when setting irq affinity
Dan Murphy [Mon, 8 Jun 2015 19:30:55 +0000 (14:30 -0500)]
net: phy: dp83867: Fix device tree entries
Fix the device tree entries to modify the '_' to '-'.
Also changes the names of the internal delay properties
from -int- to -internal- as the -int- appeared as a keyword.
Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
API compliance scanning with coccinelle flagged:
./drivers/atm/iphase.c:2621:4-20:
WARNING: timeout (50) seems HZ dependent
Numeric constants passed to schedule_timeout() make the effective
timeout HZ dependent which does not seem intended.
Fixed up by converting the constant to jiffies with msecs_to_jiffies()
As this driver was introduced in the early 2.3 series it is most
likely assuming HZ=100 so the constant 50 is converted to 500ms.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 8 Jun 2015 20:21:58 +0000 (13:21 -0700)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"About 10 days worth of small bug fixes, and the (hopefully) final
round fixes for from arm-soc land for the -rc cycle. Nothing special
to note, but here's a brief summary of fixes by SoC type:
- OMAP:
small set of misc DT fixes; boot fix for THUMB2 kernel
- mediatek:
PMIC fixes; DT fix for model name
- exynos:
wakeup interupt fixes for 3250
- mvebu:
revert mbus patch which broke DMA masters
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: am335x-boneblack: disable RTC-only sleep to avoid hardware damage
ARM: dts: AM35xx: fix system control module clocks
arm64: dts: mt8173-evb: fix model name
ARM: exynos: Fix wake-up interrupts for Exynos3250
ARM: dts: Fix n900 dts file to work around 4.1 touchscreen regression on n900
ARM: dts: Fix dm816x to use right compatible flag for MUSB
ARM: OMAP3: Fix booting with thumb2 kernel
Revert "bus: mvebu-mbus: make sure SDRAM CS for DMA don't overlap the MBus bridge window"
bus: mvebu-mbus: do not set WIN_CTRL_SYNCBARRIER on non io-coherent platforms.
ARM: mvebu: armada-xp-linksys-mamba: Disable internal RTC
soc: mediatek: Add compile dependency to pmic-wrapper
soc: mediatek: PMIC wrap: Fix register state machine handling
soc: mediatek: PMIC wrap: Fix clock rate handling
net: phy: bcm7xxx: update workaround to fix 100BaseT corner cases
Update the AFE_TX_CONFIG value to solve marginal rise/fall issues
observed when the link is operating in 100BaseT. This workaround applies
to GPHY revisions D0, E0 and newer.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: replace last open coded skb_orphan_frags with function call
Commit 70008aa50e92 ("skbuff: convert to skb_orphan_frags") replaced
open coded tests of SKBTX_DEV_ZEROCOPY and skb_copy_ubufs with calls
to helper function skb_orphan_frags. Apply that to the last remaining
open coded site.
Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bcmgenet: power on MII block for all MII modes
The RGMII block is currently only powered on when using RGMII or
RGMII_NO_ID, which is not correct when using the GENET interface in MII
or Reverse MII modes. We always need to power on the RGMII interface for
this block to properly work, regardless of the MII mode in which we
operate.
Fixes: aa09677cba423 ("net: bcmgenet: add MDIO routines") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Josh Hunt [Mon, 8 Jun 2015 16:00:59 +0000 (12:00 -0400)]
ipv6: Fix protocol resubmission
UDP encapsulation is broken on IPv6. This is because the logic to resubmit
the nexthdr is inverted, checking for a ret value > 0 instead of < 0. Also,
the resubmit label is in the wrong position since we already get the
nexthdr value when performing decapsulation. In addition the skb pull is no
longer necessary either.
This changes the return value check to look for < 0, using it for the
nexthdr on the next iteration, and moves the resubmit label to the proper
location.
With these changes the v6 code now matches what we do in the v4 ip input
code wrt resubmitting when decapsulating.
Signed-off-by: Josh Hunt <johunt@akamai.com> Acked-by: "Tom Herbert" <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Fri, 5 Jun 2015 17:51:54 +0000 (18:51 +0100)]
ipv6: fix possible use after free of dev stats
The memory pointed to by idev->stats.icmpv6msgdev,
idev->stats.icmpv6dev and idev->stats.ipv6 can each be used in an RCU
read context without taking a reference on idev. For example, through
IP6_*_STATS_* calls in ip6_rcv. These memory blocks are freed without
waiting for an RCU grace period to elapse. This could lead to the
memory being written to after it has been freed.
Fix this by using call_rcu to free the memory used for stats, as well
as idev after an RCU grace period has elapsed.
Signed-off-by: Robert Shearman <rshearma@brocade.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Kevin Hilman [Mon, 8 Jun 2015 17:31:34 +0000 (10:31 -0700)]
Merge tag 'omap-for-v4.1/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge omap fixes for v4.1, urgent fix to avoid potential hardware damage From Tony Lindgren:
Omap fixes for the -rc cycle, including a fix for potential hardware
breakage on BeagleBones:
- BeagleBones don't support RTC-only mode, it can cause hardware
damage if system-power-controller is specified without
ti,pmic-shutdown-controller
- Fix a recent regression to am3517 SoCs caused by the recent clock
move that was not noticed until now despite automated boot
testing
- Fix a regression for n900 touchscreen triggered by recent
recent input changes
- Fix compatible property for dm816x USB to avoid errors with
USB Ethernet
- Fix oops for omap3 when built with CONFIG_THUMB2_KERNEL
* tag 'omap-for-v4.1/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-boneblack: disable RTC-only sleep to avoid hardware damage
ARM: dts: AM35xx: fix system control module clocks
ARM: dts: Fix n900 dts file to work around 4.1 touchscreen regression on n900
ARM: dts: Fix dm816x to use right compatible flag for MUSB
ARM: OMAP3: Fix booting with thumb2 kernel
Linus Torvalds [Mon, 8 Jun 2015 16:37:23 +0000 (09:37 -0700)]
Merge git://git.infradead.org/intel-iommu
Pull Intel IOMMU fix from David Woodhouse:
"This fixes an oops when attempting to enable 1:1 passthrough mode for
devices on which VT-d translation was disabled anyway.
It's actually a long-standing bug but recent changes (commit 18436afdc11a: "iommu/vt-d: Allow RMRR on graphics devices too") have
made it much easier to trigger with 'iommu=pt intel_iommu=igfx_off' on
the command line"
* git://git.infradead.org/intel-iommu:
iommu/vt-d: Fix passthrough mode with translation-disabled devices
Linus Torvalds [Mon, 8 Jun 2015 15:47:08 +0000 (08:47 -0700)]
Merge branch 'for-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Two driver fixes. One is for an ahci_mvebu controller config bug and
the other fixes pata_octeon_cf build issue"
* 'for-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
pata_octeon_cf: fix broken build
ata: ahci_mvebu: Fix wrongly set base address for the MBus window setting
David S. Miller [Mon, 8 Jun 2015 07:50:49 +0000 (00:50 -0700)]
Merge branch 'phy-micrel'
Jaeden Amero says:
====================
net/phy: micrel: Center FLP timing at 16ms
In v2, we add an additional cleanup commit to make an array of strings
static const and to improve const correctness generally. We also no longer
unnecessarily initialize the result variable in
ksz9031_center_flp_timing().
In v3, we remove the unnecessary result variable from ksz9031_config_init()
introduced by a previous version of "net/phy: micrel: Center FLP timing at
16ms".
In v4, we modify the commit message of "net/phy: micrel: Center FLP timing
at 16ms" to replace the awkward quotation of the data sheet's programming
procedure with an explanation of why we program the FLP burst registers and
restart auto-negotiation where we do (config_init).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jaeden Amero [Fri, 5 Jun 2015 23:00:26 +0000 (18:00 -0500)]
net/phy: micrel: Center FLP timing at 16ms
Link failures have been observed when using the KSZ9031 with HP 1810-8G
and HP 1910-8G network switches. Center the FLP timing at 16ms to help
avoid intermittent link failures.
>From the KSZ9031RNX and KSZ9031MNX data sheets revision 2.2, section
"Auto-Negotiation Timing":
The KSZ9031[RNX or MNX] Fast Link Pulse (FLP) burst-to-burst
transmit timing for Auto-Negotiation defaults to 8ms. IEEE 802.3
Standard specifies this timing to be 16ms +/-8ms. Some PHY link
partners need to receive the FLP with 16ms centered timing;
otherwise, there can be intermittent link failures and long
link-up times.
The PHY data sheet recommends configuring the FLP burst registers after
power-up/reset and immediately thereafter restarting auto-negotiation, so
we center the FLP timing at 16ms and then restart auto-negotiation in the
config_init for KSZ9031.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Firo Yang [Mon, 8 Jun 2015 03:54:51 +0000 (11:54 +0800)]
fib_trie: coding style: Use pointer after check
As Alexander Duyck pointed out that:
struct tnode {
...
struct key_vector kv[1];
}
The kv[1] member of struct tnode is an arry that refernced by
a null pointer will not crash the system, like this:
struct tnode *p = NULL;
struct key_vector *kv = p->kv;
As such p->kv doesn't actually dereference anything, it is simply a
means for getting the offset to the array from the pointer p.
This patch make the code more regular to avoid making people feel
odd when they look at the code.
Signed-off-by: Firo Yang <firogm@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Numeric constants passed to schedule_timeout_*() make the effective
timeout HZ dependent which does not seem to be the intent here.
Fixed up by converting the constant to jiffies with msecs_to_jiffies(),
passing 100ms (assuming HZ==100 in the original code).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
API compliance scanning with coccinelle flagged:
./drivers/net/wan/cosa.c:520:2-18: WARNING:
timeout (30) seems HZ dependent
Numeric constants passed to schedule_timeout() make the effective
timeout HZ dependent which makes little sense in a device probe.
Fixed up by converting the constant to jiffies with msecs_to_jiffies()
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Majd Dibbiny [Sun, 7 Jun 2015 12:44:23 +0000 (15:44 +0300)]
net/mlx5_core: Fix static checker warnings around system guid query flow
Fix static checker warnings in the flow of system guid query.
Fixes: 707c4602cda6 ('net/mlx5_core: Add new query HCA vport commands') Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bridge: disable softirqs around br_fdb_update to avoid lockup
br_fdb_update() can be called in process context in the following way:
br_fdb_add() -> __br_fdb_add() -> br_fdb_update() (if NTF_USE flag is set)
so we need to disable softirqs because there are softirq users of the
hash_lock. One easy way to reproduce this is to modify the bridge utility
to set NTF_USE, enable stp and then set maxageing to a low value so
br_fdb_cleanup() is called frequently and then just add new entries in
a loop. This happens because br_fdb_cleanup() is called from timer/softirq
context. The spin locks in br_fdb_update were _bh before commit f8ae737deea1
("[BRIDGE]: forwarding remove unneeded preempt and bh diasables")
and at the time that commit was correct because br_fdb_update() couldn't be
called from process context, but that changed after commit: 292d1398983f ("bridge: add NTF_USE support")
Using local_bh_disable/enable around br_fdb_update() allows us to keep
using the spin_lock/unlock in br_fdb_update for the fast-path.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Fixes: 292d1398983f ("bridge: add NTF_USE support") Signed-off-by: David S. Miller <davem@davemloft.net>
isdn/hisax: Convert use of __constant_cpu_to_le16 to cpu_to_le16
In big endian cases, macro cpu_to_le16 unfolds to __swab16 which
provides special case for constants. In little endian cases,
__constant_cpu_to_le16 and cpu_to_le16 expand directly to the
same expression. So, replace __constant_cpu_to_le16 with
cpu_to_le16 with the goal of getting rid of the definition of
__constant_cpu_to_le16 completely.
The semantic patch that performs this transformation is as follows:
@@expression x;@@
- __constant_cpu_to_le16(x)
+ cpu_to_le16(x)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Fri, 5 Jun 2015 17:54:45 +0000 (18:54 +0100)]
mpls: fix possible use after free of device
The mpls device is used in an RCU read context without a lock being
held. As the memory is freed without waiting for the RCU grace period
to elapse, the freed memory could still be in use.
Address this by using kfree_rcu to free the memory for the mpls device
after the RCU grace period has elapsed.
Fixes: 03c57747a702 ("mpls: Per-device MPLS state") Signed-off-by: Robert Shearman <rshearma@brocade.com> Acked-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 7 Jun 2015 23:56:10 +0000 (16:56 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"Eight fixes across arch/mips. Nothing stands particuarly out nor is
complicated but fixes keep coming in at a higher than comfortable
rate"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: KVM: Do not sign extend on unsigned MMIO load
MIPS: BPF: Fix stack pointer allocation
MIPS: Loongson-3: Fix a cpu-hotplug issue in loongson3_ipi_interrupt()
MIPS: Fix enabling of DEBUG_STACKOVERFLOW
MIPS: c-r4k: Fix typo in probe_scache()
MIPS: Avoid an FPE exception in FCSR mask probing
MIPS: ath79: Add a missing new line in log message
MIPS: ralink: Fix clearing the illegal access interrupt
be2net: Replace dma/pci_alloc_coherent() calls with dma_zalloc_coherent()
There are several places in the driver (all in control paths) where
coherent dma memory is being allocated using either dma_alloc_coherent()
or the deprecated pci_alloc_consistent(). All these calls should be
changed to use dma_zalloc_coherent() to avoid uninitialized fields in
data structures backed by this memory.
Reported-by: Joerg Roedel <jroedel@suse.de> Tested-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fugang Duan [Fri, 5 Jun 2015 09:22:08 +0000 (17:22 +0800)]
net: fec: ptp: correct the ENET_ATCOR value
The current driver adjust freq formula is:
fe * diff = ppb * pc
Note:
fe: ENET ref clock frequency in Hz
diff = inc_corr - inc: difference between default increment and correction increment
ppb: parts per billion adjustment from base
pc: correction period (in number of fe clock cycles)
The correction increment will be used after N cycles of regular increments,
not every N cycles (with N being the correction period). For example, set ENET_ATCOR=4,
INC=8, INC_CORR=9, there will be 4 increments of 8 (ENET_ATINC[INC]) , followed by 1
increment of 9 (ENET_ATINC[INC_CORR]).
So, the correct formula is:
fe * diff = ppb * (pc + 1)
For ENET_ATCOR, a value 0 disables the correction counter and no corrections occur.
So base on the origin formula, set pc = pc > 1 ? pc - 1 : pc.
Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wilson Kok [Fri, 5 Jun 2015 07:52:57 +0000 (00:52 -0700)]
bridge: use _bh spinlock variant for br_fdb_update to avoid lockup
br_fdb_update() can be called in process context in the following way:
br_fdb_add() -> __br_fdb_add() -> br_fdb_update() (if NTF_USE flag is set)
so we need to use spin_lock_bh because there are softirq users of the
hash_lock. One easy way to reproduce this is to modify the bridge utility
to set NTF_USE, enable stp and then set maxageing to a low value so
br_fdb_cleanup() is called frequently and then just add new entries in
a loop. This happens because br_fdb_cleanup() is called from timer/softirq
context. These locks were _bh before commit f8ae737deea1
("[BRIDGE]: forwarding remove unneeded preempt and bh diasables")
and at the time that commit was correct because br_fdb_update() couldn't be
called from process context, but that changed after commit: 292d1398983f ("bridge: add NTF_USE support")
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Fixes: 292d1398983f ("bridge: add NTF_USE support") Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Simek [Fri, 5 Jun 2015 08:49:17 +0000 (10:49 +0200)]
net: ll_temac: Remove sparse warnings
Remove sparse warnings:
drivers/net/ethernet/xilinx/ll_temac_main.c:65:16: warning: cast removes
address space of expression
drivers/net/ethernet/xilinx/ll_temac_main.c:70:9: warning: cast removes
address space of expression
drivers/net/ethernet/xilinx/ll_temac_main.c:127:16: warning: cast
removes address space of expression
drivers/net/ethernet/xilinx/ll_temac_main.c:137:9: warning: cast removes
address space of expression
drivers/net/ethernet/xilinx/ll_temac_main.c:409:3: warning: symbol
'temac_options' was not declared. Should it be static?
drivers/net/ethernet/xilinx/ll_temac_main.c:590:6: warning: symbol
'temac_adjust_link' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dump useful ring statistics along with interrupt status, software
maintained pointers and hardware registers to help troubleshoot TX queue
stalls.
When a timeout occurs, disable TX NAPI for the rings, dump their states
while interrupts are disabled, re-enable interrupts, NAPI and queue flow
control to help with the recovery.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 4 Jun 2015 23:10:09 +0000 (01:10 +0200)]
net: dsa: mv88e6xxx: Fix deadlock by double lock
ethtool -S on a DSA interface can deadlock for some switches because
the same lock is taken twice. Use the register read function which
expects the lock to be already held.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Fixes: 31888234b736 ("net: dsa: mv88e6xxx: Replace stats mutex with SMI mutex") Signed-off-by: David S. Miller <davem@davemloft.net>
batman-adv: change the MAC of each VLAN upon ndo_set_mac_address
The MAC address of the soft-interface is used to initialise
the "non-purge" TT entry of each existing VLAN. Therefore
when the user invokes ndo_set_mac_address() all the
"non-purge" TT entries have to be updated, not only the one
belonging to the non-tagged network.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Sven Eckelmann [Fri, 17 Apr 2015 17:40:28 +0000 (19:40 +0200)]
batman-adv: Add required includes to all files
The header files could not be build indepdent from each other. This is
happened because headers didn't include the files for things they've used.
This was problematic because the success of a build depended on the
knowledge about the right order of local includes.
Also source files were not including everything they've used explicitly.
Instead they required that transitive includes are always stable. This is
problematic because some transitive includes are not obvious, depend on
config settings and may not be stable in the future.
The order for include blocks are:
* primary headers (main.h and the *.h file of a *.c file)
* global linux headers
* required local headers
* extra forward declarations for pointers in function/struct declarations
The only exceptions are linux/bitops.h and linux/if_ether.h in packet.h.
This header file is shared with userspace applications like batctl and must
therefore build together with userspace applications. The header
linux/bitops.h is not part of the uapi headers and linux/if_ether.h
conflicts with the musl implementation of netinet/if_ether.h. The
maintainers rejected the use of __KERNEL__ preprocessor checks and thus
these two headers are only in main.h. All files using packet.h first have
to include main.h to work correctly.
Reported-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Sven Eckelmann [Sun, 1 Mar 2015 08:46:18 +0000 (09:46 +0100)]
batman-adv: Use common Jenkins Hash implementation
An unoptimized version of the Jenkins one-at-a-time hash function is used
and partially copied all over the code wherever an hashtable is used.
Instead the optimized version shared between the whole kernel should be
used to reduce code duplication and use better optimized code.
Only the DAT code must use the old implementation because it is used as
distributed hash function which has to be common for all nodes.
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
bpf: allow programs to write to certain skb fields
allow programs read/write skb->mark, tc_index fields and
((struct qdisc_skb_cb *)cb)->data.
mark and tc_index are generically useful in TC.
cb[0]-cb[4] are primarily used to pass arguments from one
program to another called via bpf_tail_call() which can
be seen in sockex3_kern.c example.
All fields of 'struct __sk_buff' are readable to socket and tc_cls_act progs.
mark, tc_index are writeable from tc_cls_act only.
cb[0]-cb[4] are writeable by both sockets and tc_cls_act.
Add verifier tests and improve sample code.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bpf: make programs see skb->data == L2 for ingress and egress
eBPF programs attached to ingress and egress qdiscs see inconsistent skb->data.
For ingress L2 header is already pulled, whereas for egress it's present.
This is known to program writers which are currently forced to use
BPF_LL_OFF workaround.
Since programs don't change skb internal pointers it is safe to do
pull/push right around invocation of the program and earlier taps and
later pt->func() will not be affected.
Multiple taps via packet_rcv(), tpacket_rcv() are doing the same trick
around run_filter/BPF_PROG_RUN even if skb_shared.
This fix finally allows programs to use optimized LD_ABS/IND instructions
without BPF_LL_OFF for higher performance.
tc ingress + cls_bpf + samples/bpf/tcbpf1_kern.o
w/o JIT w/JIT
before 20.5 23.6 Mpps
after 21.8 26.6 Mpps
Old programs with BPF_LL_OFF will still work as-is.
We can now undo most of the earlier workaround commit: a166151cbe33 ("bpf: fix bpf helpers to use skb->mac_header relative offsets")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
amd-xgbe: Use disable_irq_nosync from within timer function
Since the Tx timer function runs in softirq context the driver needs
to call disable_irq_nosync instead of a disable_irq.
Reported-by: Josh Stone <jistone@redhat.com> Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix:
drivers/net/wan/dscc4.c: In function 'dscc4_open':
drivers/net/wan/dscc4.c:1049:25: warning: variable 'ppriv' set but not used
[-Wunused-but-set-variable]
This has been in there unused since 1da177e4c3f (Linux-2.6.12-rc2) simply
remove it.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 7 Jun 2015 04:17:57 +0000 (21:17 -0700)]
inet: add IP_BIND_ADDRESS_NO_PORT to overcome bind(0) limitations
When an application needs to force a source IP on an active TCP socket
it has to use bind(IP, port=x).
As most applications do not want to deal with already used ports, x is
often set to 0, meaning the kernel is in charge to find an available
port.
But kernel does not know yet if this socket is going to be a listener or
be connected.
It has very limited choices (no full knowledge of final 4-tuple for a
connect())
With limited ephemeral port range (about 32K ports), it is very easy to
fill the space.
This patch adds a new SOL_IP socket option, asking kernel to ignore
the 0 port provided by application in bind(IP, port=0) and only
remember the given IP address.
The port will be automatically chosen at connect() time, in a way
that allows sharing a source port as long as the 4-tuples are unique.
This new feature is available for both IPv4 and IPv6 (Thanks Neal)
Tested:
Wrote a test program and checked its behavior on IPv4 and IPv6.
strace(1) shows sequences of bind(IP=127.0.0.2, port=0) followed by
connect().
Also getsockname() show that the port is still 0 right after bind()
but properly allocated after connect().
Linus Torvalds [Sun, 7 Jun 2015 05:37:45 +0000 (22:37 -0700)]
Merge tag 'driver-core-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two fixes for the driver core that resolve some reported
issues.
One is a regression from 4.0, the other a fixes a reported oops that
has been there since 3.19.
Both have been in linux-next for a while with no problems"
* tag 'driver-core-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers/base: cacheinfo: handle absence of caches
drivers: of/base: move of_init to driver_init
Linus Torvalds [Sun, 7 Jun 2015 05:33:08 +0000 (22:33 -0700)]
Merge tag 'staging-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO fixes from Greg KH:
"Here are some IIO driver fixes to resolve reported issues, some ozwpan
fixes for some reported CVE problems, and a rtl8712 driver fix for a
reported regression.
All have been in linux-next successfully"
* tag 'staging-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8712: fix stack dump
ozwpan: unchecked signed subtraction leads to DoS
ozwpan: divide-by-zero leading to panic
ozwpan: Use unsigned ints to prevent heap overflow
ozwpan: Use proper check to prevent heap overflow
iio: adc: twl6030-gpadc: Fix modalias
iio: adis16400: Fix burst transfer for adis16448
iio: adis16400: Fix burst mode
iio: adis16400: Compute the scan mask from channel indices
iio: adis16400: Use != channel indices for the two voltage channels
iio: adis16400: Report pressure channel scale
Linus Torvalds [Sun, 7 Jun 2015 05:14:23 +0000 (22:14 -0700)]
Merge tag 'tty-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a few TTY and Serial driver fixes for reported regressions
and crashes.
All of these have been in linux-next with no reported problems"
* tag 'tty-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
n_tty: Fix auditing support for cannonical mode
serial: 8250_omap: provide complete custom startup & shutdown callbacks
n_tty: Fix calculation of size in canon_copy_from_read_buf
serial: imx: Fix DMA handling for IDLE condition aborts
serial/amba-pl011: Unconditionally poll for FIFO space before each TX char
projects / karo-tx-linux.git / log