Antti Palosaari [Thu, 11 Dec 2014 18:44:51 +0000 (15:44 -0300)]
[media] cx23885: fix I2C scan printout
1) I2C slave addresses were printed so called 8-bit format. Use
standard 7-bit notation.
2) I2C slave address was printed with hex formatted without leading
zeros, which makes output one digit shorter in a case of address
fit to one hex digit. Use 4 char wide hex number with leading zeros
as usually used for I2C slave addresses.
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
[media] vb2-vmalloc: Protect DMA-specific code by #ifdef CONFIG_HAS_DMA
If NO_DMA=y:
drivers/built-in.o: In function `vb2_vmalloc_dmabuf_ops_detach':
videobuf2-vmalloc.c:(.text+0x6f11b0): undefined reference to `dma_unmap_sg'
drivers/built-in.o: In function `vb2_vmalloc_dmabuf_ops_map':
videobuf2-vmalloc.c:(.text+0x6f1266): undefined reference to `dma_unmap_sg'
videobuf2-vmalloc.c:(.text+0x6f1282): undefined reference to `dma_map_sg'
As we don't want to make the core VIDEOBUF2_VMALLOC depend on HAS_DMA
(it's v4l2 core code, and selected by a lot of drivers), stub out the
DMA support if HAS_DMA is not set.
James Hogan [Mon, 8 Dec 2014 16:17:07 +0000 (13:17 -0300)]
[media] rc-main: Re-apply filter for no-op protocol change
Since commit da6e162d6a46 ("[media] rc-core: simplify sysfs code"), when
the IR protocol is set using the sysfs interface to the same set of
protocols that are already set, store_protocols() does not refresh the
scancode filter with the new protocol, even if it has already called the
change_protocol() callback successfully. This results in the filter
being disabled in the hardware and not re-enabled until the filter is
set again using sysfs.
Fix in store_protocols() by still re-applying the filter whenever the
change_protocol() driver callback succeeded.
The problem can be reproduced with the img-ir driver by setting a
filter, and then setting the protocol to the same protocol that is
already set:
$ echo nec > protocols
$ echo 0xffff > filter_mask
$ echo nec > protocols
After this, messages which don't match the filter were still being
received.
[media] staging: media: lirc: lirc_zilog.c: keep consistency in dev functions
The previous patch switched some dev functions to move the string to a second
line. Doing this for all similar functions because it makes the driver easier
to read if all similar lines use the same criteria.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
checkpatch makes an exception to the 80-colum rule for quotes strings, and
Documentation/CodingStyle recommends not splitting quotes strings across lines
because it breaks the ability to grep for the string. Fixing these.
WARNING: quoted string split across lines
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sifan Naeem [Thu, 11 Dec 2014 20:06:23 +0000 (17:06 -0300)]
[media] rc: img-ir: pass toggle bit to the rc driver
Add toggle bit to struct img_ir_scancode_req so that protocols can
provide it to img_ir_handle_data(), and pass that toggle bit up to
rc_keydown instead of 0.
This is needed for the upcoming rc-5 and rc-6 patches.
Sifan Naeem [Thu, 11 Dec 2014 20:06:22 +0000 (17:06 -0300)]
[media] rc: img-ir: add scancode requests to a struct
The information being requested of hardware decode callbacks through
the img-ir-hw scancode API is mounting up, so combine it into a struct
which can be passed in with a single pointer rather than multiple
pointer arguments. This allows it to be extended more easily without
touching all the hardware decode callbacks.
Russell King [Sat, 20 Dec 2014 12:45:20 +0000 (09:45 -0300)]
[media] em28xx: ensure "closing" messages terminate with a newline
The lockdep splat addressed in a previous commit revealed that at
least one message in em28xx-input.c was missing a new line:
em28178 #0: Closing input extensionINFO: trying to register non-static key.
Further inspection shows several other messages also miss a new line.
These will be fixed in a subsequent patch.
Fixes: aa929ad783c0 ("[media] em28xx: print a message at disconnect") Cc: <stable@vger.kernel.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Russell King [Sat, 20 Dec 2014 12:45:15 +0000 (09:45 -0300)]
[media] em28xx: fix em28xx-input removal
Removing the em28xx-rc module results in the following lockdep splat,
which is caused by trying to call cancel_delayed_work_sync() on an
uninitialised delayed work. Fix this by ensuring we always initialise
the work.
Fixes: f52226099382 ("[media] em28xx: extend the support for device buttons") Cc: <stable@vger.kernel.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Benoit Parrot [Tue, 9 Dec 2014 19:43:44 +0000 (16:43 -0300)]
[media] media: platform: add VPFE capture driver support for AM437X
This patch adds Video Processing Front End (VPFE) driver for
AM437X family of devices
Driver supports the following:
- V4L2 API using MMAP buffer access based on videobuf2 api
- Asynchronous sensor/decoder sub device registration
- DT support
Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Darren Etheridge <detheridge@ti.com> Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
[hans.verkuil@cisco.com: swapped two lines to fix vpfe_release() & add pinctrl include] Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sakari Ailus [Fri, 3 Oct 2014 14:38:32 +0000 (11:38 -0300)]
[media] smiapp: Replace pll_flags quirk with more generic init quirk
The pll_flags quirk just returned the extra PLL flags the sensor required,
but the init quirk is far more versatile. It can be used to perform any
extra initialisation needed by the sensor, including allocating memory for
sensor specific struct and creating sensor specific new controls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sakari Ailus [Tue, 9 Dec 2014 16:48:58 +0000 (13:48 -0300)]
[media] smiapp: Separate late controls from the rest
The default values and limits for certain controls need the knowledge of
available media bus codes or link frequencies. Create such controls later
on, so that most of the initialisation of the sensor has already been done
when the init quirk is called.
[mchehab@osg.samsung.com: make checkpatch.pl happier] Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sakari Ailus [Tue, 9 Dec 2014 17:35:43 +0000 (14:35 -0300)]
[media] smiapp: Clean up smiapp_init_controls()
Clean up smiapp_init_controls() by adding newlines to appropriate places and
by removing superfluous error handling. The caller will clean up control
handlers in any case if the function fails.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sakari Ailus [Sun, 14 Sep 2014 21:53:06 +0000 (18:53 -0300)]
[media] smiapp: Fully probe the device in probe
In the case of platform data, ISPs that provide clocks to the sensor must
probe before the sensor does. Accessing the sensor does require the clocks,
and thus, probe cannot access the sensor in such a system.
This limitation does not exist in the case of the DT. Perform all
initialisation except Media entity initialisation, link creation and
sub-device registration in probe.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sakari Ailus [Sun, 14 Sep 2014 20:59:00 +0000 (17:59 -0300)]
[media] smiapp: Split sub-device initialisation off from the registered callback
The registered callback is called by the V4L2 async framework after the
bound callback. This allows separating the functionality in the registered
callback so that on DT based systems only sub-device registration is done
there.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sakari Ailus [Sat, 18 Oct 2014 09:11:19 +0000 (06:11 -0300)]
[media] smiapp: Remove FSF's address from the license header
Remove FSF's address information from the license header in the smiapp
driver and the smiapp-pll PLL calculator. This should no longer be needed,
and would be rendered outdated in case the FSF chooses to relocate its
office.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Timo Ahonen <timo.ahonen@nokia.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Aviv Greenberg [Wed, 3 Dec 2014 11:14:09 +0000 (08:14 -0300)]
[media] v4l: Add packed Bayer raw10 pixel formats
These formats are just like 10-bit raw bayer formats that exist already, but
the pixels are not padded to byte boundaries. Instead, the eight high order
bits of four consecutive pixels are stored in four bytes, followed by a byte
of two low order bits of each of the four pixels.
Signed-off-by: Aviv Greenberg <aviv.d.greenberg@intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sakari Ailus [Sun, 7 Dec 2014 22:56:38 +0000 (19:56 -0300)]
[media] DocBook: v4l: Fix raw bayer pixel format documentation wording
The documentation began with "The following four pixel formats"... but the
format definitions preceded this sentence. Replace it with "These four pixel
formats".
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
[media] VIDEO_CAFE_CCIC should select VIDEOBUF2_DMA_SG
If VIDEO_CAFE_CCIC=y, but VIDEOBUF2_DMA_SG=m:
drivers/built-in.o: In function `mcam_v4l_open':
mcam-core.c:(.text+0x1c2e81): undefined reference to `vb2_dma_sg_memops'
mcam-core.c:(.text+0x1c2eb0): undefined reference to `vb2_dma_sg_init_ctx'
drivers/built-in.o: In function `mcam_v4l_release':
mcam-core.c:(.text+0x1c34bf): undefined reference to `vb2_dma_sg_cleanup_ctx'
Hans Verkuil [Sat, 13 Dec 2014 11:53:00 +0000 (08:53 -0300)]
[media] s5k5baf: fix sparse warnings
drivers/media/i2c/s5k5baf.c:1796:33: warning: duplicate const
drivers/media/i2c/s5k5baf.c:379:24: warning: cast to restricted __le16
drivers/media/i2c/s5k5baf.c:437:11: warning: incorrect type in assignment (different base types)
drivers/media/i2c/s5k5baf.c:445:16: warning: incorrect type in return expression (different base types)
Hans Verkuil [Sat, 13 Dec 2014 11:52:57 +0000 (08:52 -0300)]
[media] m5mols: fix sparse warnings
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
The be16_to_cpu conversions in m5mols_get_version() are not needed since the
data is already using cpu endianness. This was never noticed since these
version fields are never used.
Hans Verkuil [Sat, 13 Dec 2014 11:52:56 +0000 (08:52 -0300)]
[media] hd29l2: fix sparse error and warnings
drivers/media/dvb-frontends/hd29l2.c:29:18: warning: Variable length array is used.
drivers/media/dvb-frontends/hd29l2.c:34:32: error: cannot size expression
drivers/media/dvb-frontends/hd29l2.c:125:5: warning: symbol 'hd29l2_rd_reg_mask' was not declared. Should it be static?
Variable length arrays are frowned upon, so replace with a fixed length and check
that there won't be a buffer overrun.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Sat, 13 Dec 2014 11:52:54 +0000 (08:52 -0300)]
[media] videobuf2-vmalloc: fix sparse warning
Fix this warning:
drivers/media/v4l2-core/videobuf2-vmalloc.c:98:28: warning: incorrect type in assignment (different address spaces)
drivers/media/v4l2-core/videobuf2-vmalloc.c:158:28: warning: incorrect type in argument 1 (different address spaces)
The warning is correct, but we have no other choice here to forcibly cast.
At least it is now explicit that such a cast is needed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Sat, 13 Dec 2014 11:52:52 +0000 (08:52 -0300)]
[media] budget-core: fix sparse warnings
Fixes these sparse warnings.
drivers/media/pci/ttpci/budget-core.c:250:17: warning: context imbalance in 'ttpci_budget_debiread' - different lock contexts for basic block
drivers/media/pci/ttpci/budget-core.c:289:17: warning: context imbalance in 'ttpci_budget_debiwrite' - different lock contexts for basic block
To be honest, the new code does look better than the old.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Mon, 1 Dec 2014 13:10:44 +0000 (10:10 -0300)]
[media] v4l2 core: improve debug flag handling
The old debug field is renamed to dev_debug to ensure that existing drivers
(including out-of-tree drivers) that try to use the old name will no longer
compile. A comment has also been added that makes it explicit that drivers
shouldn't use this field.
Additional bits have been added to the debug flag to be more fine-grained
when debugging, especially when dealing with streaming ioctls and read,
write and poll. You want to enable those explicitly to prevent flooding
the log when streaming unless you actually want to do that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It made motion event never appear in my installation.
That code is complicated, so I couldn't figure out quickly how to fix
it, so dropping it seems better to me.
Another justification is that anyway application would implement
"motion signal stabilization" if required, it is not necessarily kernel
driver's job.
Hans Verkuil [Fri, 12 Dec 2014 13:28:00 +0000 (10:28 -0300)]
[media] cx25821: remove video output support
The video output functionality never worked for this driver. Now remove the
creation of the output video nodes as well to prevent users from thinking
that video output is available, when it isn't.
To correctly implement this the video output should use vb2 as well, and
that requires rewriting the output DMA setup. But without hardware to test
I am not able to do that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Fri, 12 Dec 2014 13:27:56 +0000 (10:27 -0300)]
[media] btcx-risc: move to bt8xx
The btcx-risc module is no longer used by other drivers except for bttv.
So move it from common to bt8xx and make it part of the bttv driver instead
of as a separate module.
This module should never have been a common module since most of the code
has always been bttv specific.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Fri, 12 Dec 2014 13:27:55 +0000 (10:27 -0300)]
[media] cx231xx: remove btcx_riscmem reference
Remove this comment block, it's unused. This removes the btcx_riscmem
reference as well, since that will no longer be available to other
drivers except bttv.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Takanari Hayama [Thu, 27 Nov 2014 01:25:02 +0000 (22:25 -0300)]
[media] v4l: vsp1: Always enable virtual RPF when BRU is in use
Regardless of a number of inputs, we should always enable virtual RPF
when BRU is used. This allows the case when there's only one input to
BRU, and a size of the input is smaller than a size of an output of BRU.
William Manley [Mon, 8 Dec 2014 18:57:58 +0000 (15:57 -0300)]
[media] uvcvideo: Add GUID for BGR 8:8:8
The Magewell XI100DUSB-HDMI[1] video capture device reports the pixel
format "e436eb7d-524f-11ce-9f53-0020af0ba770". This is its GUID for
BGR 8:8:8.
The UVC 1.5 spec[2] only defines GUIDs for YUY2, NV12, M420 and I420.
This seems to be an extension documented in the Microsoft Windows Media
Format SDK[3] - or at least the Media Format SDK was the only hit that
Google gave when searching for the GUID. This Media Format SDK defines
this GUID as corresponding to `MEDIASUBTYPE_RGB24`. Note though, the
XI100DUSB outputs BGR e.g. byte-reversed. I don't know if its the
capture device in error or Microsoft mean BGR when they say RGB.
Lad, Prabhakar [Wed, 26 Nov 2014 23:25:44 +0000 (20:25 -0300)]
[media] media: usb: uvc: use vb2_ops_wait_prepare/finish helper
This patch drops driver specific wait_prepare() and wait_finish()
callbacks from vb2_ops and instead uses the the helpers
vb2_ops_wait_prepare/finish() provided by the vb2 core, the lock member
of the queue needs to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Laurent Pinchart [Tue, 28 Oct 2014 12:07:37 +0000 (09:07 -0300)]
[media] v4l: omap4iss: Stop started entities when pipeline start fails
If an entity can't be started when starting a pipeline we need to clean
up by stopping all entities that have been successfully started.
Otherwise the hardware and software states won't match, potentially
leading to crashes (for instance due to the CSI2 receiver receiving
interrupts with a NULL pipeline pointer).
[media] v4l: omap4iss: csi2: Perform real frame number propagation
Compute the pipeline frame number from the frame number sent by the
sensor instead of incrementing the frame number in software. This
improves dropped frames detection.
[media] v4l: omap4iss: Remove bogus frame number propagation
Frame number propagation tries to increase the robustness of the frame
number counter by using sources less likely to be missed than the end of
frame interrupts, such as hardware frame counters or start of frame
interrupts.
Increasing the frame number in the IPIPE ISIF and resizer end of frame
interrupt handlers is pointless as it doesn't bring any improvement.
Don't do it.
Hans Verkuil [Thu, 4 Dec 2014 09:54:52 +0000 (06:54 -0300)]
[media] v4l2 subdevs: replace get/set_crop by get/set_selection
The crop and selection pad ops are duplicates. Replace all uses of get/set_crop
by get/set_selection. This will make it possible to drop get/set_crop
altogether.
Prabhakar Lad [Wed, 26 Nov 2014 22:42:32 +0000 (19:42 -0300)]
[media] media: s5p-mfc: use vb2_ops_wait_prepare/finish helper
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Prabhakar Lad [Wed, 26 Nov 2014 22:42:30 +0000 (19:42 -0300)]
[media] media: s5p-tv: use vb2_ops_wait_prepare/finish helper
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Prabhakar Lad [Wed, 26 Nov 2014 22:42:28 +0000 (19:42 -0300)]
[media] media: sh_veu: use vb2_ops_wait_prepare/finish helper
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Prabhakar Lad [Wed, 26 Nov 2014 22:42:26 +0000 (19:42 -0300)]
[media] media: exynos-gsc: use vb2_ops_wait_prepare/finish helper
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Prabhakar Lad [Wed, 26 Nov 2014 22:42:25 +0000 (19:42 -0300)]
[media] media: ti-vpe: use vb2_ops_wait_prepare/finish helper
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Prabhakar Lad [Wed, 26 Nov 2014 22:42:24 +0000 (19:42 -0300)]
[media] media: s3c-camif: use vb2_ops_wait_prepare/finish helper
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Linus Torvalds [Sun, 21 Dec 2014 00:48:59 +0000 (16:48 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux
Pull ACCESS_ONCE cleanup preparation from Christian Borntraeger:
"kernel: Provide READ_ONCE and ASSIGN_ONCE
As discussed on LKML http://marc.info/?i=54611D86.4040306%40de.ibm.com
ACCESS_ONCE might fail with specific compilers for non-scalar
accesses.
Here is a set of patches to tackle that problem.
The first patch introduce READ_ONCE and ASSIGN_ONCE. If the data
structure is larger than the machine word size memcpy is used and a
warning is emitted. The next patches fix up several in-tree users of
ACCESS_ONCE on non-scalar types.
This does not yet contain a patch that forces ACCESS_ONCE to work only
on scalar types. This is targetted for the next merge window as Linux
next already contains new offenders regarding ACCESS_ONCE vs.
non-scalar types"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux:
s390/kvm: REPLACE barrier fixup with READ_ONCE
arm/spinlock: Replace ACCESS_ONCE with READ_ONCE
arm64/spinlock: Replace ACCESS_ONCE READ_ONCE
mips/gup: Replace ACCESS_ONCE with READ_ONCE
x86/gup: Replace ACCESS_ONCE with READ_ONCE
x86/spinlock: Replace ACCESS_ONCE with READ_ONCE
mm: replace ACCESS_ONCE with READ_ONCE or barriers
kernel: Provide READ_ONCE and ASSIGN_ONCE
Linus Torvalds [Sun, 21 Dec 2014 00:42:36 +0000 (16:42 -0800)]
Merge tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux
Pull clk framework updates from Mike Turquette:
"This is much later than usual due to several last minute bugs that had
to be addressed. As usual the majority of changes are new drivers and
modifications to existing drivers. The core recieved many fixes along
with the groundwork for several large changes coming in the future
which will better parition clock providers from clock consumers"
* tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: samsung: Fix Exynos 5420 pinctrl setup and clock disable failure due to domain being gated
ARM: OMAP3: clock: fix boot breakage in legacy mode
ARM: OMAP2+: clock: fix DPLL code to use new determine rate APIs
clk: Really fix deadlock with mmap_sem
clk: mmp: fix sparse non static symbol warning
clk: Change clk_ops->determine_rate to return a clk_hw as the best parent
clk: change clk_debugfs_add_file to take a struct clk_hw
clk: Don't expose __clk_get_accuracy
clk: Don't try to use a struct clk* after it could have been freed
clk: Remove unused function __clk_get_prepare_count
clk: samsung: Fix double add of syscore ops after driver rebind
clk: samsung: exynos4: set parent of sclk_hdmiphy to hdmi
clk: samsung: exynos4415: Fix build with PM_SLEEP disabled
clk: samsung: remove unnecessary inclusion of header files from clk.h
clk: samsung: remove unnecessary CONFIG_OF from clk.c
clk: samsung: Spelling s/bwtween/between/
clk: rockchip: Add support for the mmc clock phases using the framework
clk: rockchip: add bindings for the mmc clocks
clk: rockchip: rk3288 export i2s0_clkout for use in DT
clk: rockchip: use clock ID for DMC (memory controller) on rk3288
...
Linus Torvalds [Sat, 20 Dec 2014 21:52:52 +0000 (13:52 -0800)]
Merge branch 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull more i2c updates from Wolfram Sang:
"Included are two bugfixes needing some bigger refactoring (sh_mobile:
deferred probe with DMA, mv64xxx: fix offload support) and one
deprecated driver removal I thought would go in via ppc but I
misunderstood. It has a proper ack from BenH"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sh_mobile: fix uninitialized var when debug is enabled
macintosh: therm_pm72: delete deprecated driver
i2c: sh_mobile: I2C_SH_MOBILE should depend on HAS_DMA
i2c: sh_mobile: rework deferred probing
i2c: sh_mobile: refactor DMA setup
i2c: mv64xxx: rework offload support to fix several problems
i2c: mv64xxx: use BIT() macro for register value definitions
Linus Torvalds [Sat, 20 Dec 2014 21:42:57 +0000 (13:42 -0800)]
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI update from James Bottomley:
"This is a much shorter set of patches that were on the go but didn't
make it in to the early pull request for the merge window. It's
really a set of bug fixes plus some final cleanup work on the new tag
queue API"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
storvsc: ring buffer failures may result in I/O freeze
ipr: set scsi_level correctly for disk arrays
ipr: add support for async scanning to speed up boot
scsi_debug: fix missing "break;" in SDEBUG_UA_CAPACITY_CHANGED case
scsi_debug: take sdebug_host_list_lock when changing capacity
scsi_debug: improve driver description in Kconfig
scsi_debug: fix compare and write errors
qla2xxx: fix race in handling rport deletion during recovery causes panic
scsi: blacklist RSOC for Microsoft iSCSI target devices
scsi: fix random memory corruption with scsi-mq + T10 PI
Revert "[SCSI] mpt3sas: Remove phys on topology change"
Revert "[SCSI] mpt2sas: Remove phys on topology change."
esas2r: Correct typos of "validate" in a comment
fc: FCP_PTA_SIMPLE is 0
ibmvfc: remove unused tag variable
scsi: remove MSG_*_TAG defines
scsi: remove scsi_set_tag_type
scsi: remove scsi_get_tag_type
scsi: never drop to untagged mode during queue ramp down
scsi: remove ->change_queue_type method
Linus Torvalds [Sat, 20 Dec 2014 21:37:44 +0000 (13:37 -0800)]
Merge tag 'pm-config-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull CONFIG_PM_RUNTIME elimination from Rafael Wysocki:
"This removes the last few uses of CONFIG_PM_RUNTIME introduced
recently and makes that config option finally go away.
CONFIG_PM will be available directly from the menu now and also it
will be selected automatically if CONFIG_SUSPEND or CONFIG_HIBERNATION
is set"
* tag 'pm-config-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: Eliminate CONFIG_PM_RUNTIME
tty: 8250_omap: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound: sst-haswell-pcm: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
Linus Torvalds [Sat, 20 Dec 2014 21:33:03 +0000 (13:33 -0800)]
Merge branch 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull misc kbuild changes from Michal Marek:
"There are only a few things in the misc branch:
- Fix for bugon.cocci semantic patch
- Kdevelop4 files are .gitignored
- Put make binrpm-pkg on diet"
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scripts/package: binrpm-pkg do not create source and devel package
.gitignore: Add Kdevelop4 project files
bugon.cocci: fix Options at the macro
Linus Torvalds [Sat, 20 Dec 2014 21:31:14 +0000 (13:31 -0800)]
Merge branch 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild updates from Michal Marek:
"Here are the kbuild changes for v3.19-rc1:
- Cleanups and deduplication in the main Makefile and
scripts/Makefile.*
- Sort the output of *config targets in make help
- Old <linux/version.h> is always removed to avoid a surprise during
bisecting
- Warning fix in kconfig"
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: remove redundant -rR flag of hdr-inst
kbuild: Fix make help-<board series> on powerpc
kbuild: Automatically remove stale <linux/version.h> file
kconfig: Fix warning "‘jump’ may be used uninitialized"
Makefile: sort list of defconfig targets in make help output
kbuild: Remove duplicate $(cmd) definition in Makefile.clean
kbuild: collect shorthands into scripts/Kbuild.include
Linus Torvalds [Sat, 20 Dec 2014 02:19:19 +0000 (18:19 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs pile #3 from Al Viro:
"Assorted fixes and patches from the last cycle"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
[regression] chunk lost from bd9b51
vfs: make mounts and mountstats honor root dir like mountinfo does
vfs: cleanup show_mountinfo
init: fix read-write root mount
unfuck binfmt_misc.c (broken by commit e6084d4)
vm_area_operations: kill ->migrate()
new helper: iter_is_iovec()
move_extent_per_page(): get rid of unused w_flags
lustre: get rid of playing with ->fs
btrfs: filp_open() returns ERR_PTR() on failure, not NULL...
projects / karo-tx-linux.git / log