David Woodhouse [Sat, 6 Oct 2007 18:44:12 +0000 (14:44 -0400)]
[MTD] [NAND] Fix PCI ident table for CAFÉ NAND controller.
It was only the very early prototypes which made the mistake of using
the same device ident for all three functions on the device -- don't
bother trying to express that in the PCI match table, since the tools
don't cope. We can check in the probe routine instead, just in case.
Also remember to terminate the table.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch make the OneNAND driver much less racy. It fixes
our "onenand_wait: read timeout!" heisenbugs. The reason of
these bugs was that the driver did not lock the chip when
accessing OTP, and it screwed up OneNAND state when the OTP
was read while JFFS2 was doing FS checking.
This patch also fixes other races I spotted:
1. BBT was not protected
2. Access to ecc_stats was not protected
Now the chip is locked when BBT is accessed.
To fix all of these I basically split all interface functions
on 'function()' and 'function_nolock()' parts.
I tested this patch on N800 hardware - it fixes our problems.
But I tested a little different version because our OneNAND
codebase is slightly out-of-date. But it should be OK.
This patch also includes the prin fixes I posted before.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
David Woodhouse [Sun, 23 Sep 2007 17:51:25 +0000 (18:51 +0100)]
[MTD] map driver for NOR flash on the Intel Vermilion Range chipset
The Vermilion Range Expansion Bus supports four chip selects, each of which
has 64MiB of address space. The 2nd BAR of the Expansion Bus PCI Device
is a 256MiB memory region containing the address spaces for all four of
the chip selects, with start addresses hardcoded on 64MiB boundaries.
This map driver only supports NOR flash on chip select 0. The buswidth
(either 8 bits or 16 bits) is determined by reading the Expansion Bus Timing
and Control Register for Chip Select 0 (EXP_TIMING_CS0).
Signed-off-by: Andy Lowe <alowe@mvista.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Andy Lowe [Fri, 12 Jan 2007 23:05:24 +0000 (18:05 -0500)]
[JFFS2] Fix unpoint length
Fix a couple of instances in JFFS2 where the unpoint() routine is
being called with the wrong length in cases where the point() routine
truncated a request.
Signed-off-by: Andy Lowe <alowe@mvista.com> Signed-off-by: Nicolas Pitre <nico@cam.org> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Andy Lowe [Fri, 12 Jan 2007 23:05:10 +0000 (18:05 -0500)]
[MTD] fix CFI point method for discontiguous maps
The CFI probe routine is capable of detecting flash banks consisting of
identical chips mapped to physically discontiguous addresses. (One
common way this can occur is if a flash bank is populated with chips of
less capacity than the hardware was designed to support.) The CFI
point() routine currently ignores any such gaps. This patch fixes
the CFI point() routine so that it truncates any request that would
span a gap.
Signed-off-by: Andy Lowe <alowe@mvista.com> Signed-off-by: Nicolas Pitre <nico@cam.org> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Todd Poynor [Mon, 7 Nov 2005 21:47:48 +0000 (21:47 +0000)]
[MTD] MAPS: Merge Lubbock and Mainstone drivers into common PXA2xx driver
Replace Lubbock and Mainstone board drivers with common PXA2xx driver,
convert to platform driver (corresponding platform device changes merged
to kernel.org for 2.6.15), add power management callbacks.
Signed-off-by: Todd Poynor <tpoynor@mvista.com> Signed-off-by: Nicolas Pitre <npitre@mvista.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Artem Bityutskiy [Tue, 28 Aug 2007 17:33:32 +0000 (20:33 +0300)]
[MTD] [NAND] nandsim: avoid deadlocking FS
Make nandsim use GFP_NOFS when allocating memory, because it might
be used by a file-system (e.g. UBIFS2) which means, if we are short
of memory, we may deadlock. Indee, UBIFS is holding a lock, writes
to the media, reaches this place in NANDsim, kmalloc does not find
the requested amount of RAM, calls memory shrinker, which decides
to writeback inodes, calls FS, and it deadlocks on the lock which
is already being held. Below is the UBIFS backtrace which
demonstrates that:
The deadlock is funny because it starts in pdflush/writeback,
and comes back to writeback, then deadlocks. It seems we should look
carefully for other places in UBI and MTD and use GFP_NOFS instead
of GFP_KERNEL.
Caught-by: Adrian Hunter <ext-adrian.hunter@nokia.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
David Woodhouse [Thu, 6 Sep 2007 08:40:21 +0000 (09:40 +0100)]
[MTD] Fix CFI build error when no map width or interleave supported
When building NOR flash support, you have compile-time options for the
bus width and the number of individual chips which are interleaved
together onto that bus. The code to deal with arbitrary geometry is a
bit convoluted, and people want to just configure it for the specific
hardware they have, to avoid the runtime overhead.
Selecting _none_ of the available options doesn't make any sense. You
should have at least one. This makes it build though, since people
persist in trying.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Jörn Engel [Wed, 29 Aug 2007 15:57:11 +0000 (17:57 +0200)]
[MTD] [NAND] Driver for Olympus MAUSB-10 and Fujifilm DPC-R1 card readers
Unlike most stuff on the market the chip inside these two allows raw
flash access and doesn't implement and FTL, leaving that functionality
to the device driver.
Raw flash access in a cheap USB cardreader! An MTD test device one can
attach to a PC! What a deal!
The command set of the chip is not documented, so information was
obtained from the existing mass-storage driver
(drivers/usb/storage/alauda.c), its documentation
(http://alauda.sourceforge.net/wikka.php?wakka=BulkCommandReference),
additional reverse engineering and comparison with a vendor driver for a
related chip
(http://www.ratocsystems.com/english/download/driver/linux/sma03u.html).
Signed-off-by: Joern Engel <joern@logfs.org> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Mel Gorman [Wed, 22 Aug 2007 21:02:05 +0000 (14:02 -0700)]
Apply memory policies to top two highest zones when highest zone is ZONE_MOVABLE
The NUMA layer only supports NUMA policies for the highest zone. When
ZONE_MOVABLE is configured with kernelcore=, the the highest zone becomes
ZONE_MOVABLE. The result is that policies are only applied to allocations
like anonymous pages and page cache allocated from ZONE_MOVABLE when the
zone is used.
This patch applies policies to the two highest zones when the highest zone
is ZONE_MOVABLE. As ZONE_MOVABLE consists of pages from the highest "real"
zone, it's always functionally equivalent.
The patch has been tested on a variety of machines both NUMA and non-NUMA
covering x86, x86_64 and ppc64. No abnormal results were seen in
kernbench, tbench, dbench or hackbench. It passes regression tests from
the numactl package with and without kernelcore= once numactl tests are
patched to wait for vmstat counters to update.
akpm: this is the nasty hack to fix NUMA mempolicies in the presence of
ZONE_MOVABLE and kernelcore= in 2.6.23. Christoph says "For .24 either merge
the mobility or get the other solution that Mel is working on. That solution
would only use a single zonelist per node and filter on the fly. That may
help performance and also help to make memory policies work better."
Signed-off-by: Mel Gorman <mel@csn.ul.ie> Acked-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Tested-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Acked-by: Christoph Lameter <clameter@sgi.com> Cc: Andi Kleen <ak@suse.de> Cc: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Wed, 22 Aug 2007 21:02:01 +0000 (14:02 -0700)]
newport_con warning fix
drivers/video/console/newport_con.c: In function `newport_console_init':
drivers/video/console/newport_con.c:743: warning: return makes integer from pointer without a cast
Although one wonders whether that should have been -ENODEV...
Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Wed, 22 Aug 2007 21:02:01 +0000 (14:02 -0700)]
selection.h: add tty_struct forward declaration
In file included from drivers/video/console/newport_con.c:16:
include/linux/selection.h:16: warning: "struct tty_struct" declared inside parameter list
include/linux/selection.h:16: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
xen-head.S does not come back to the data section, leaving the text section
as current section. It causes problems with a slightly enhanced DEBUG_RODATA
that supports CONFIG_HOTPLUG and bringing a CPU up after the text has been
marked read-only: reference to early_gdt_descr causes a page fault.
Updates:
- It should be using pushsection/popsection.
- Actually, the push/popsections around the ELFNOTEs are redundant; ELFNOTE()
does its own push/popsection to put things into the appropriate .note* section
anyway.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Acked-by: Jeremy Fitzhardinge <jeremy@xensource.com> Cc: Chris Wright <chrisw@sous-sol.org> Cc: Andi Kleen <ak@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 22 Aug 2007 21:01:58 +0000 (14:01 -0700)]
exec: kill unsafe BUG_ON(sig->count) checks
de_thread:
if (atomic_read(&oldsighand->count) <= 1)
BUG_ON(atomic_read(&sig->count) != 1);
This is not safe without the rmb() in between. The results of two
correctly ordered __exit_signal()->atomic_dec_and_test()'s could be seen
out of order on our CPU.
The same is true for the "thread_group_empty()" case, __unhash_process()'s
changes could be seen before atomic_dec_and_test(&sig->count).
On some platforms (including i386) atomic_read() doesn't provide even the
compiler barrier, in that case these checks are simply racy.
Remove these BUG_ON()'s. Alternatively, we can do something like
David Brownell [Wed, 22 Aug 2007 21:01:57 +0000 (14:01 -0700)]
rtc-max6902 minor fixes
Minor tweaks to rtc-max6902: make it hotplug correctly, and fix a few
space-before-tab whitespace botches. This driver has no current in-tree
users, so the hotplug fix changes the driver name.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Print a big fat warning and do what is necessary to continue if a node is
marked as up (meaning either node is online (upstream) or node has memory
(Andrew's tree)) but allocations from the node do not succeed.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olof Johansson [Wed, 22 Aug 2007 21:01:55 +0000 (14:01 -0700)]
serial: add pci ids for PA Semi PWRficient onchip uarts
Add PCI IDs for the onchip UARTs on PA Semi PWRficient.
Signed-off-by: Olof Johansson <olof@lixom.net> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ian Kent [Wed, 22 Aug 2007 21:01:54 +0000 (14:01 -0700)]
autofs4: deadlock during create
Due to inconsistent locking in the VFS between calls to lookup and
revalidate deadlock can occur in the automounter.
The inconsistency is that the directory inode mutex is held for both lookup
and revalidate calls when called via lookup_hash whereas it is held only
for lookup during a path walk. Consequently, if the mutex is held during a
call to revalidate autofs4 can't release the mutex to callback the daemon
as it can't know whether it owns the mutex.
This situation happens when a process tries to create a directory within an
automount and a second process also tries to create the same directory
between the lookup and the mkdir. Since the first process has dropped the
mutex for the daemon callback, the second process takes it during
revalidate leading to deadlock between the autofs daemon and the second
process when the daemon tries to create the mount point directory.
After spending quite a bit of time trying to resolve this on more than one
occassion, using rather complex and ulgy approaches, it turns out that just
delaying the hashing of the dentry until the create operation works fine.
Signed-off-by: Ian Kent <raven@themaw.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Dike [Wed, 22 Aug 2007 21:01:53 +0000 (14:01 -0700)]
uml: fix previous request size limit fix
The previous patch which limited the number of sectors in a single request
to a COWed device was correct in concept, but the limit was implemented in
the wrong place.
By putting it in ubd_add, it covered the cases where the COWing was
specified on the command line. However, when the command line only has the
COW file specified, the fact that it's a COW file isn't known until it's
opened, so the limit is missed in these cases.
This patch moves the sector limit from ubd_add to ubd_open_dev.
Signed-off-by: Jeff Dike <jdike@linux.intel.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Wed, 22 Aug 2007 21:01:53 +0000 (14:01 -0700)]
md: correctly update sysfs when a raid1 is reshaped
When a raid1 array is reshaped (number of drives changed), the list of devices
is compacted, so that slots for missing devices are filled with working
devices from later slots. This requires the "rd%d" symlinks in sysfs to be
updated.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Wed, 22 Aug 2007 21:01:52 +0000 (14:01 -0700)]
md: make sure a re-add after a restart honours bitmap when resyncing
Commit 1757128438d41670ded8bc3bc735325cc07dc8f9 was slightly bad. If an array
has a write-intent bitmap, and you remove a drive, then readd it, only the
changed parts should be resynced. However after the above commit, this only
works if the array has not been shut down and restarted.
This is because it sets 'fullsync' at little more often than it should. This
patch is more careful.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adam Litke [Wed, 22 Aug 2007 21:01:51 +0000 (14:01 -0700)]
Fix VM_FAULT flags conversion for hugetlb
It seems a simple mistake was made when converting follow_hugetlb_page()
over to the VM_FAULT flags bitmasks (in "mm: fault feedback #2", commit 83c54070ee1a2d05c89793884bea1a03f2851ed4).
By using the wrong bitmask, hugetlb_fault() failures are not being
recognized. This results in an infinite loop whenever follow_hugetlb_page
is involved in a failed fault.
Signed-off-by: Adam Litke <agl@us.ibm.com> Acked-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Siddha, Suresh B [Wed, 22 Aug 2007 21:01:49 +0000 (14:01 -0700)]
slab: skip calling cache_free_alien() when the platform is not numa capable
Skip calling cache_free_alien() when the platform is not numa capable.
This will avoid cache misses that happen while accessing slabp (which is
per page memory reference) to get nodeid. Instead use a global variable to
skip the call, which is mostly likely to be present in the cache.
This gives a 0.8% performance boost with the database oltp workload on a
quad-core SMP platform and by any means the number is not small :)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Acked-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 22 Aug 2007 21:01:48 +0000 (14:01 -0700)]
signalfd: make it group-wide, fix posix-timers scheduling
With this patch any thread can dequeue its own private signals via signalfd,
even if it was created by another sub-thread.
To do so, we pass "current" to dequeue_signal() if the caller is from the same
thread group. This also fixes the scheduling of posix timers broken by the
previous patch.
If the caller doesn't belong to this thread group, we can't handle __SI_TIMER
case properly anyway. Perhaps we should forbid the cross-process signalfd usage
and convert ctx->tsk to ctx->sighand.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Davide Libenzi <davidel@xmailserver.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Michael Kerrisk <mtk-manpages@gmx.net> Cc: Roland McGrath <roland@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 22 Aug 2007 21:01:42 +0000 (14:01 -0700)]
signalfd: fix interaction with posix-timers
dequeue_signal:
if (__SI_TIMER) {
spin_unlock(&tsk->sighand->siglock);
do_schedule_next_timer(info);
spin_lock(&tsk->sighand->siglock);
}
Unless tsk == curent, this is absolutely unsafe: nothing prevents tsk from
exiting. If signalfd was passed to another process, do_schedule_next_timer()
is just wrong.
Add yet another "tsk == current" check into dequeue_signal().
This patch fixes an oopsable bug, but breaks the scheduling of posix timers
if the shared __SI_TIMER signal was fetched via signalfd attached to another
sub-thread. Mostly fixed by the next patch.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Davide Libenzi <davidel@xmailserver.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Michael Kerrisk <mtk-manpages@gmx.net> Cc: Roland McGrath <roland@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 22 Aug 2007 21:01:37 +0000 (14:01 -0700)]
posix-timers: fix creation race
sys_timer_create() sets ->it_process and unlocks ->siglock, then checks
tmr->it_sigev_notify to define if get_task_struct() is needed.
We already passed ->it_id to the caller, another thread can delete this timer
and free its memory in between.
As a minimal fix, move this code under ->siglock, sys_timer_delete() takes it
too before calling release_posix_timer(). A proper serialization would be to
take ->it_lock, we add a partly initialized timer on posix_timers_id, not
good.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
timer->it_process is checked in lock_timer() to prevent access to a
timer, which is on the way to be deleted, but the check happens after
idr_lock is dropped. This allows release_posix_timer() to delete the
timer before the lock code can check the timer:
Introduce CONFIG_CHECK_SIGNATURE to control inclusion of check_signature()
and avoid problems on platforms that don't have readb().
Let the few legacy (ISA || PCI || X86) drivers that need check_signature()
select CONFIG_CHECK_SIGNATURE.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Jeff Dike <jdike@addtoit.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Roman Zippel <zippel@linux-m68k.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
m68k/mac: Make mac_hid_mouse_emulate_buttons() declaration visible
m68k/mac: Make mac_hid_mouse_emulate_buttons() declaration visible
drivers/char/keyboard.c: In function 'kbd_keycode':
drivers/char/keyboard.c:1142: error: implicit declaration of function 'mac_hid_mouse_emulate_buttons'
The forward declaration of mac_hid_mouse_emulate_buttons() is not visible on
m68k because it's hidden in the middle of a big #ifdef block.
Move it to <linux/kbd_kern.h>, correct the type of the second parameter, and
include <linux/kbd_kern.h> where needed.
Roman Zippel [Wed, 22 Aug 2007 21:01:33 +0000 (14:01 -0700)]
m68k: Dont include RODATA into text segment
Don't include RODATA into text segment as it includes the kallsyms data and
can cause spurious link failures (layout differences can change the number of
symbols in kallsyms, i.e. when a symbol is equal to _etext it's not
included).
Signed-off-by: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Berg [Wed, 22 Aug 2007 21:01:31 +0000 (14:01 -0700)]
remove dead code in via-pmu68k
When suspend is ever implemented for pmu68k it really should follow the
generic pm_ops concept and not mirror the platform-specific /dev/pmu
device with ioctls on it. Hence, this patch removes the unused code there;
should the implementers need it they can look at via-pmu.c and/or the
history of the file.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Wed, 22 Aug 2007 21:01:28 +0000 (14:01 -0700)]
fix NULL pointer dereference in __vm_enough_memory()
The new exec code inserts an accounted vma into an mm struct which is not
current->mm. The existing memory check code has a hard coded assumption
that this does not happen as does the security code.
As the correct mm is known we pass the mm to the security method and the
helper function. A new security test is added for the case where we need
to pass the mm and the existing one is modified to pass current->mm to
avoid the need to change large amounts of code.
(Thanks to Tobias for fixing rejects and testing)
Signed-off-by: Alan Cox <alan@redhat.com> Cc: WU Fengguang <wfg@mail.ustc.edu.cn> Cc: James Morris <jmorris@redhat.com> Cc: Tobias Diedrich <ranma+kernel@tdiedrich.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Wed, 22 Aug 2007 21:01:27 +0000 (14:01 -0700)]
correct name for rtc-m41t80
The new rtc-m41t80 driver name doesn't match its module name, which
prevents it from properly hotplugging. Since it's new, no platforms yet
depend on that name ... so this patch fixes the driver name to match its
module name, rather than going the other way around with a MODULE_ALIAS().
NOTE: This sort of bug is a new thing to watch out for with new-style I2C
drivers; previously I2C couldn't hotplug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy Whitcroft [Wed, 22 Aug 2007 21:01:26 +0000 (14:01 -0700)]
synchronous lumpy reclaim: wait for page writeback when directly reclaiming contiguous areas
Lumpy reclaim works by selecting a lead page from the LRU list and then
selecting pages for reclaim from the order-aligned area of pages. In the
situation were all pages in that region are inactive and not referenced by any
process over time, it works well.
In the situation where there is even light load on the system, the pages may
not free quickly. Out of a area of 1024 pages, maybe only 950 of them are
freed when the allocation attempt occurs because lumpy reclaim returned early.
This patch alters the behaviour of direct reclaim for large contiguous
blocks.
The first attempt to call shrink_page_list() is asynchronous but if it fails,
the pages are submitted a second time and the calling process waits for the IO
to complete. This may stall allocators waiting for contiguous memory but that
should be expected behaviour for high-order users. It is preferable behaviour
to potentially queueing unnecessary areas for IO. Note that kswapd will not
stall in this fashion.
[apw@shadowen.org: update to version 2]
[apw@shadowen.org: update to version 3] Signed-off-by: Mel Gorman <mel@csn.ul.ie> Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy Whitcroft [Wed, 22 Aug 2007 21:01:25 +0000 (14:01 -0700)]
synchronous lumpy reclaim: ensure we count pages transitioning inactive via clear_active_flags
As pointed out by Mel when reclaim is applied at higher orders a significant
amount of IO may be started. As this takes finite time to drain reclaim will
consider more areas than ultimatly needed to satisfy the request. This leads
to more reclaim than strictly required and reduced success rates.
I was able to confirm Mel's test results on systems locally. These show that
even under light load the success rates drop off far more than expected.
Testing with a modified version of his patch (which follows) I was able to
allocate almost all of ZONE_MOVABLE with a near idle system. I ran 5 test
passes sequentially following system boot (the system has 29 hugepages in
ZONE_MOVABLE):
2.6.23-rc1 11 8 6 7 7
sync_lumpy 28 28 29 29 26
These show that although hugely better than the near 0% success normally
expected we can only allocate about a 1/4 of the zone. Using synchronous
reclaim for these allocations we get close to 100% as expected.
I have also run our standard high order tests and these show no regressions in
allocation success rates at rest, and some significant improvements under
load.
This patch:
We are transitioning pages from active to inactive in clear_active_flags,
those need counting as PGDEACTIVATE vm events.
Signed-off-by: Andy Whitcroft <apw@shadowen.org> Acked-by: Mel Gorman <mel@csn.ul.ie> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Neuling [Wed, 22 Aug 2007 23:31:42 +0000 (09:31 +1000)]
Documentation: fix getdelays.c printf bug
Commit b663a79c191508f27cd885224b592a878c0ba0f6 ("taskstats: add
context-switch counters") incorrectly removed a comma from a printf
statement. This causes corruption in the output printing or a seg
fault.
Andrew Morton [Wed, 22 Aug 2007 21:01:20 +0000 (14:01 -0700)]
free_irq(): fix DEBUG_SHIRQ handling
If we're going to run the handler from free_irq() then we must do it with
local irq's disabled. Otherwise lockdep complains that the handler is taking
irq-safe spinlocks in a non-irq-safe fashion.
Cc: Ingo Molnar <mingo@elte.hu> Cc: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add blacklisting capability to serial_pci to avoid misdetection of serial ports
The serial_pci driver tries to guess serial ports on unknown devices based
on the PCI class (modem or serial). On certain softmodems (AC'97 modems)
this can lead to the recognition of non-existing serial ports.
This patch adds a blacklist of PCI IDs that are to be ignored by the driver.
[akpm@linux-foundation.org: cleanups] Signed-off-by: Christian Schmidt <schmidt@digadd.de> Cc: Bjorn Helgaas <bjorn.helgaas@hp.com> Cc: Russell King <rmk+lkml@arm.linux.org.uk> Cc: Yinghai Lu <yinghai.lu@sun.com> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Corey Minyard [Wed, 22 Aug 2007 21:01:18 +0000 (14:01 -0700)]
Serial 8250: handle saving the clear-on-read bits from the LSR and MSR
Reading the LSR clears the break, parity, frame error, and overrun bits in
the 8250 chip, but these are not being saved in all places that read the
LSR. Same goes for the MSR delta bits. Save the LSR bits off whenever the
lsr is read so they can be handled later in the receive routine. Save the
MSR bits to be handled in the modem status routine.
Also, clear the stored bits and clear the interrupt registers before
enabling interrupts, to avoid handling old values of the stored bits in the
interrupt routines.
[akpm@linux-foundation.org: clean up pre-existing code] Signed-off-by: Corey Minyard <minyard@acm.org> Cc: Russell King <rmk+lkml@arm.linux.org.uk> Cc: Yinghai Lu <yinghai.lu@sun.com> Cc: Bjorn Helgaas <bjorn.helgaas@hp.com> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Niels de Vos [Wed, 22 Aug 2007 21:01:14 +0000 (14:01 -0700)]
serial: add support for ITE 887x chips
Add support for the it887x-chips (PCI) manufactured by ITE.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com> Cc: Russell King <rmk@arm.linux.org.uk> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Woodhouse [Wed, 22 Aug 2007 21:01:11 +0000 (14:01 -0700)]
serial: don't optimise away baud rate changes when BOTHER is used
The uart_set_termios() function will bail out early without bothering to
touch the hardware, if it decides that nothing "relevant" has changed.
Unfortunately, its idea of "relevant" doesn't include c_[io]speed. So if
the baud rate bits are BOTHER and you just change the speed, the change
gets optimised away.
This patch makes it ignore the old Bfoo bits in c_cflag and just check
whether c_ispeed and c_ospeed have changed. Those integers are always set
appropriately for us by set_termios().
Signed-off-by: David Woodhouse <dwmw2@infradead.org> Acked-by: Alan Cox <alan@redhat.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lee Schermerhorn [Wed, 22 Aug 2007 21:01:06 +0000 (14:01 -0700)]
Document Linux Memory Policy
I couldn't find any memory policy documentation in the Documentation
directory, so here is my attempt to document it.
There's lots more that could be written about the internal design--including
data structures, functions, etc. However, if you agree that this is better
that the nothing that exists now, perhaps it could be merged. This will
provide a baseline for updates to document the many policy patches that are
currently being worked.
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: Christoph Lameter <clameter@sgi.com> Cc: Andi Kleen <ak@suse.de> Cc: Michael Kerrisk <mtk-manpages@gmx.net> Acked-by: Rob Landley <rob@landley.net> Acked-by: Mel Gorman <mel@csn.ul.ie> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kent Yoder [Wed, 22 Aug 2007 21:01:04 +0000 (14:01 -0700)]
tpmdd maintainers
Fix up the maintainers info in the tpm drivers. Kylene will be out for
some time, so copying the sourceforge list is the best way to get some
attention.
Cc: Marcel Selhorst <tpm@selhorst.net> Cc: Kylene Jo Hall <kjhall@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy Whitcroft [Wed, 22 Aug 2007 21:01:03 +0000 (14:01 -0700)]
sparsemem: ensure we initialise the node mapping for SPARSEMEM_STATIC
Booting SPARSEMEM on NUMA systems trips a BUG in page_alloc.c:
Initializing HighMem for node 0 (00038000:00100000)
Initializing HighMem for node 1 (00100000:001ffe00)
------------[ cut here ]------------
kernel BUG at /home/apw/git/linux-2.6/mm/page_alloc.c:456!
[...]
This occurs because the section to node id mapping is not being
setup correctly during init under SPARSEMEM_STATIC, leading to an
attempt to free pages from all nodes into the zones on node 0.
When the zone_table[] was removed in the following commit, a new
section to node mapping table was introduced:
That conversion inadvertantly only initialised the node mapping in
SPARSEMEM_EXTREME. Ensure we initialise the node mapping in
SPARSEMEM_STATIC.
[akpm@linux-foundation.org: make the stubs static inline] Signed-off-by: Andy Whitcroft <apw@shadowen.org> Cc: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ryusuke Konishi [Wed, 22 Aug 2007 21:01:02 +0000 (14:01 -0700)]
eCryptfs: fix lookup error for special files
When ecryptfs_lookup() is called against special files, eCryptfs generates
the following errors because it tries to treat them like regular eCryptfs
files.
Error opening lower file for lower_dentry [0xffff810233a6f150], lower_mnt [0xffff810235bb4c80], and flags [0x8000]
Error opening lower_file to read header region
Error attempting to read the [user.ecryptfs] xattr from the lower file; return value = [-95]
Valid metadata not found in header region or xattr region; treating file as unencrypted
For instance, the problem can be reproduced by the steps below.
# mkdir /root/crypt /mnt/crypt
# mount -t ecryptfs /root/crypt /mnt/crypt
# mknod /mnt/crypt/c0 c 0 0
# umount /mnt/crypt
# mount -t ecryptfs /root/crypt /mnt/crypt
# ls -l /mnt/crypt
This patch fixes it by adding a check similar to directories and
symlinks.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Acked-by: Michael Halcrow <mhalcrow@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] Add support for 1533 bridge to alim1535_wdt
[WATCHDOG] Add a 00-INDEX file to Documentation/watchdog/
[WATCHDOG] Eurotechwdt.c - clean-up comments
Linus Torvalds [Wed, 22 Aug 2007 18:13:22 +0000 (11:13 -0700)]
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC32]: Revert f642b263800e6e57c377d630be6d2a999683b579.
[SPARC64]: Need to clobber global reg vars in switch_to().
Linus Torvalds [Wed, 22 Aug 2007 18:13:00 +0000 (11:13 -0700)]
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IRDA] irda_nl_get_mode: always results in failure
[PPP]: Fix output buffer size in ppp_decompress_frame().
[IRDA]: Avoid a label defined but not used warning in irda_init()
[IPV6]: Fix kernel panic while send SCTP data with IP fragments
[SNAP]: Check packet length before reading
[DCCP]: Allocation in atomic context
Linus Torvalds [Wed, 22 Aug 2007 18:12:08 +0000 (11:12 -0700)]
Merge branch 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Change atomic_read/set to inline functions with barrier semantics.
[S390] kprobes: fix instruction length calculation
[S390] hypfs: inode corruption due to missing locking
[S390] disassembler: fix b2 opcodes like srst, bsg, and others
[S390] vmur: fix reference counting for vmur device structure
[S390] vmur: fix diag14 exceptions with addresses > 2GB.
[S390] qdio: Refresh buffer states for IQDIO Asynchronous output queue
[S390] qdio: fix EQBS handling on CCQ96
[S390] cio: change confusing message in cmf.
[S390] cio: dont forget to set last slot to NULL in ccw_uevent().
Zachary Amsden [Wed, 22 Aug 2007 01:30:36 +0000 (18:30 -0700)]
Fix lazy mode vmalloc synchronization for paravirt
Touching vmalloc memory in the middle of a lazy mode update can generate
a kernel PDE update, which must be flushed immediately. The fix is to
leave lazy mode when doing a vmalloc sync.
Heiko Carstens [Wed, 22 Aug 2007 11:51:45 +0000 (13:51 +0200)]
[S390] Change atomic_read/set to inline functions with barrier semantics.
After doing some tests this seems to be the best variant for s390 and
should be correct as well. With gcc 4.2.1 we get the following kernel
image sizes using the default configuration:
atomic_t type volatile, atomic_read/set defines 5311824 bytes
atomic_t type int, atomic_read/set defines 5270864 bytes
atomic_t type int, atomic_read/set inline asm 5279056 bytes
atomic_t type int, atomic_read/set inline barrier 5270864 bytes
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Placing a kprobe on "bc" instruction (s390/s390x) can cause an oops.
The instruction length is encoded into the first two bits of the s390
instruction. Kprobe is incorrectly computing the instruction length.
The instruction length is used for determining what type of "fix-up" is
needed for conditional branch instruction. The problem can bee seen by
placing a kprobe on a "bc" instruction that will not branch. The
results is that Kprobe incorrectly computes the new instruction
pointer (psw.addr) after single stepping the instruction. The problem
is corrected with this patch.
Signed-off-by: David Wilder <dwilder@us.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Michael Holzheu [Wed, 22 Aug 2007 11:51:43 +0000 (13:51 +0200)]
[S390] hypfs: inode corruption due to missing locking
hypfs removes the whole hypfs directory tree and creates a new one, when a
process triggers an update by writing to the "update" attribute. When removing
and creating files, it is necessary to lock the inode of the parent directory
where the files live. Currently hypfs does not lock the parent inode, which
can lead to inode corruption. This patch:
* Introduces correct locking
* Fixes i_nlink reference counting for inodes, when creating directories
* Adds info printk, when hypfs filesystem has been mounted
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
[S390] disassembler: fix b2 opcodes like srst, bsg, and others
The instruction table for b2 opcodes was missing an opfrag value
for the cpya instruction. All instructions specified after cpya
were not considered by the disassembler. The fix is simple and
obvious - add the opfrag field to the cpya instruction.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Michael Holzheu [Wed, 22 Aug 2007 11:51:41 +0000 (13:51 +0200)]
[S390] vmur: fix reference counting for vmur device structure
When a vmur device is removed due to a detach of the device, currently the
ur device structure is freed. Unfortunately it can happen, that there is
still a user of the device structure, when the character device is open
during the detach process. To fix this, reference counting for the vmur
structure is introduced.
In addition to that, the online, offline, probe and remove functions are
serialized now using a global mutex.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Michael Holzheu [Wed, 22 Aug 2007 11:51:40 +0000 (13:51 +0200)]
[S390] vmur: fix diag14 exceptions with addresses > 2GB.
There are several s390 diagnose calls, which must be executed below the
2GB memory boundary. In order to enforce this, those diagnoses must be
compiled into the kernel. Currently diag 14 can be called within the
vmur kernel module from addresses above 2GB. This leads to specification
exceptions. This patch moves diag10, diag14 and diag210 into the new
diag.c file.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Klaus D. Wacker [Wed, 22 Aug 2007 11:51:39 +0000 (13:51 +0200)]
[S390] qdio: Refresh buffer states for IQDIO Asynchronous output queue
Hipersocket Multicast queue works asynchronously. When sending buffers,
the buffer state change may happen delayed. The tasklet for checking
changes in the outbound queue excluded IQDIO async queues from this
process. This created either a hang situation when the queue ran full,
or presented a hang situation a interface close time.
The tasklet processing is changed to include IQDIO async queues when
requesting buffer state refresh.
Signed-off-by: Klaus D. Wacker <kdwacker@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Klaus D. Wacker [Wed, 22 Aug 2007 11:51:38 +0000 (13:51 +0200)]
[S390] qdio: fix EQBS handling on CCQ96
QDIO returned from EQBS instruction in any case after return code
CCQ=96 was issued regardless whether buffer states for at least one
buffer were extracted or not.
This caused FCP devices to hang when running under z/VM and having
QIOASSASIST=ON and having high I/O rates.
In order to fix this qdio return code processing of EQBS instruction
after CCQ=96 is changed that buffers are returned and if no buffers
where extracted the instruction is repeated at once.
Signed-off-by: Klaus D. Wacker <kdwacker@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cornelia Huck [Wed, 22 Aug 2007 11:51:37 +0000 (13:51 +0200)]
[S390] cio: change confusing message in cmf.
cmf currently prints a message that more than 4096 channels are not
allowed in basic mode - however, this can only be enforced if cmf was
a module (which is no longer possible). It makes much more sense to
not check the specified number of channels and just print a message if
the block for basic mode could not be allocated (which may happen for
any number of specified channels).
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Andrew Morton [Fri, 10 Aug 2007 21:01:31 +0000 (14:01 -0700)]
[MTD] mtdoops printk warning fixes
drivers/mtd/mtdoops.c: In function 'mtdoops_inc_counter':
drivers/mtd/mtdoops.c:109: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
drivers/mtd/mtdoops.c: In function 'mtdoops_console_sync':
drivers/mtd/mtdoops.c:277: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
someone buy Dave an x86_64 box.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Andrew Morton [Fri, 10 Aug 2007 21:01:30 +0000 (14:01 -0700)]
[JFFS2] fix printk warning in jffs2_block_check_erase()
fs/jffs2/erase.c: In function 'jffs2_block_check_erase':
fs/jffs2/erase.c:355: warning: format '%08x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
and
fs/jffs2/erase.c: In function 'jffs2_erase_pending_blocks':
fs/jffs2/erase.c:404: warning: 'bad_offset' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
David Woodhouse [Wed, 22 Aug 2007 11:39:19 +0000 (12:39 +0100)]
[JFFS2] Fix ACL vs. mode handling.
When POSIX ACL support was enabled, we weren't writing correct
legacy modes to the medium on inode creation, or when the ACL was set.
This meant that the permissions would be incorrect after the file system
was remounted.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Andy Whitcroft [Wed, 22 Aug 2007 04:23:39 +0000 (21:23 -0700)]
[IRDA] irda_nl_get_mode: always results in failure
It seems an extraneous trailing ';' has slipped in to the error handling for a
name registration failure causing the error path to trigger unconditionally.
Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[PPP]: Fix output buffer size in ppp_decompress_frame().
This patch addresses the issue with "osize too small" errors in mppe
encryption. The patch fixes the issue with wrong output buffer size
being passed to ppp decompression routine.
--------------------
As pointed out by Suresh Mahalingam, the issue addressed by
ppp-fix-osize-too-small-errors-when-decoding patch is not fully resolved yet.
The size of allocated output buffer is correct, however it size passed to
ppp->rcomp->decompress in ppp_generic.c if wrong. The patch fixes that.
--------------------
Signed-off-by: Konstantin Sharlaimov <konstantin.sharlaimov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Wed, 22 Aug 2007 03:59:08 +0000 (20:59 -0700)]
[IPV6]: Fix kernel panic while send SCTP data with IP fragments
If ICMP6 message with "Packet Too Big" is received after send SCTP DATA,
kernel panic will occur when SCTP DATA is send again.
This is because of a bad dest address when call to skb_copy_bits().
The messages sequence is like this:
Endpoint A Endpoint B
<------- SCTP DATA (size=1432)
ICMP6 message ------->
(Packet Too Big pmtu=1280)
<------- Resend SCTP DATA (size=1432)
------------kernel panic---------------
@@ -761,7 +762,7 @@ slow_path:
/*
* Copy a block of the IP datagram.
*/
- if (skb_copy_bits(skb, ptr, frag->h.raw, len))
+ if (skb_copy_bits(skb, ptr, skb_transport_header(skb),
len))
BUG();
left -= len;
====================
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Signed-off-by: David S. Miller <davem@davemloft.net>
The problem was that GFP_KERNEL was used; fixed by using gfp_any().
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Robin Getz [Wed, 22 Aug 2007 03:14:58 +0000 (23:14 -0400)]
fix - ensure we don't use bootconsoles after init has been released
Gerd Hoffmann pointed out that my patch from yesterday can lead
to a null pointer dereference if the kernel is booted with no
console, and no earlyprintk defined. This fixes that issue.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kumar Gala [Wed, 22 Aug 2007 00:15:31 +0000 (19:15 -0500)]
[POWERPC] Fix PCI Device ID for MPC8544/8533 processors
The initial user manuals for MPC8544/8533 had some issues with properly
documenting the device IDs for MPC8544/8533. These processors are almost
identical and both show up on the reference boards.
Fix up the quirks for PCIe support to handle MPC8533/E.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
projects / linux-beck.git / log