Chris Wilson [Wed, 22 Sep 2010 17:17:01 +0000 (18:17 +0100)]
drm/i915/crt: Use a DDC probe on 0xA0 before load-detect
The BIOS writer's guide suggests that a VGA connection will ACK a write
to address 0xA0 and that this should be used before doing legacy
load-detection. Considering the extreme cost of load-detection,
performing an extra DDC seems a risk worth taking.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Chris Wilson [Wed, 22 Sep 2010 09:54:48 +0000 (10:54 +0100)]
drm/i915: Don't offset the pin used for crt_ddc
Previously when converting the GMBUS pin to the GPIO reg, we would
offset the pin by one and then use the look-up table. Now that we first
try to use the GMBUS pin, we no longer need the offset and can use the
value from the VBIOS directly.
Reported-by: Carlos R. Mafra <crmafra2@gmail.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Chris Wilson [Tue, 21 Sep 2010 13:06:12 +0000 (14:06 +0100)]
drm/i915/lvds: Unlock the PP register when panel-fitting
As we do not wait for the panel to turn off when we need to adjust the
panel-fitting registers we also need to unlock the PLLs as with the
non-pfit update path.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Chris Wilson [Wed, 8 Sep 2010 15:30:16 +0000 (16:30 +0100)]
drm/i915: Drop crtc->fb pin on disable.
In order to handle disable_functions() where the framebuffer is
decoupled from the crtc we need to unpin the fb in order to prevent a
leak.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29857 Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Chris Wilson [Wed, 8 Sep 2010 08:45:11 +0000 (09:45 +0100)]
drm/i915: Disable output polling across suspend & resume
Suspending (especially hibernating) may take a finite amount of time,
during which a hotplug event may trigger and we will attempt to handle
it with inconsistent state. Disable hotplug polling around suspend and
resume.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30070 Reported-by: Rui Tiago Matos <tiagomatos@gmail.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Daniel Vetter [Sat, 11 Sep 2010 19:31:04 +0000 (21:31 +0200)]
intel-gtt: generic (insert|remove)_entries for i830
Well, not all too generic because it does not yet support dmar.
Add a new function check_flags to ensure that non-gem code does
not try to screw us over.
v2: Beautify i830_check_flags with an idea from Chris Wilson.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Daniel Vetter [Tue, 7 Sep 2010 20:41:04 +0000 (22:41 +0200)]
intel-gtt: introduce pte write function for i8xx/i915/i945
And put it to use in the gtt configuration code that writes
the scratch page addr in all gtt ptes. This makes intel_i830_configure
generic, hence rename it to intel_fake_agp_configure.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Daniel Vetter [Tue, 7 Sep 2010 20:11:15 +0000 (22:11 +0200)]
intel-gtt: initialize our own scratch page
The intel gtt fake agp driver is the only agp driver to use dma
address remapping. So it makes sense to fold this code back into the
only user (and thus reduce the reliance on the agp code).
This patch does the first step by initializing (and remapping) the
scratch page in a new function intel_gtt_setup_scratch_page.
Unfortunately intel_gtt_cleanup had to move to avoid a forward
declaration. The new scratch page is not yet used, though.
v2: Refactor out scratch page teardown. Suggested by Chris Wilson on
irc. This makes it clear what's going on and results in a nice
symmetry between setup and teardown.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Chris Wilson [Mon, 20 Sep 2010 16:36:15 +0000 (17:36 +0100)]
drm/i915: Track pinned objects
Keep a list of pinned objects and display it via debugfs. Now all
objects that exist in the GTT are always tracked on one of the
active, flushing, inactive or pinned lists.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Chris Wilson [Mon, 20 Sep 2010 10:40:50 +0000 (11:40 +0100)]
drm/i915: Track gpu fence usage
Track if the gpu requires the fence for the execution of a batch buffer
and so only wait upon the retirement of the object's last rendering
seqno if the fence is in use by the GPU.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
drm/i915: add a new BSD ring buffer for Sandybridge
This ring buffer is used for video decoding/encoding on Sandybridge.
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
drm/i915: add set_tail hook in struct intel_ring_buffer
This is prepared for video codec ring buffer on Sandybridge. It is
needed to read/write more than one register to move the tail pointer of
the video codec ring on Sandybridge.
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
drm/i915: do not export the instances of struct intel_ring_buffer
Introduce intel_init_render_ring_buffer(), intel_init_bsd_ring_buffer
for ring initialization.
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Chris Wilson [Sun, 19 Sep 2010 11:38:26 +0000 (12:38 +0100)]
drm/i915: Clean up bo lists on all hung gpus
Previously we only tidied up the active bo lists for chipsets were we
would attempt to reset the GPU. However, this action is necessary for
the system to continue and reclaim the dead bo for all chipsets.
Pointed out, in passing, by Owain Ainsworth.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Chris Wilson [Sat, 18 Sep 2010 10:02:01 +0000 (11:02 +0100)]
drm/i915: Only emit a flush request on the active ring.
When flushing the GPU domains,we emit a flush on *both* rings, even
though they share a unified cache. Only emit the flush on the currently
active ring.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Chris Wilson [Sat, 18 Sep 2010 00:38:04 +0000 (01:38 +0100)]
drm/i915: Inline i915_gem_ring_retire_request()
Change the semantics to retire any buffer older than the current seqno
rather than repeatedly calling calling the function to retire the
buffer at the head of the list matching the request seqno.
Whilst this should have no semantic impact on the implementation, Daniel
was wondering if there was a bug where we might miss a retirement and so
end up with a continually growing active list.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Chris Wilson [Sat, 18 Sep 2010 07:08:06 +0000 (08:08 +0100)]
drm/i915: After a reset perform a forced modeset
On more recent chipsets, restoring the display is not as simple as
writing a few registers, so force a full modeset of the current
configuration in order to retrain the display link.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The graphics domains are listed as GRDOM in the documentation, and the
GDRST PCI config register (0xc0) is only valid on I965 and GM45. Newer
chips (like Sandy Bridge) have a different GDRST.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
drm/i915: Actually set the reset bit in i965_reset.
Previously, it was only being set if passed GDRST_FULL - but the only
caller passed GDRST_RENDER. So the hardware never actually reset.
The comments also did not match the code.
Instead, just set the reset bit regardless of what flags were passed.
The GPU now resets correctly on my GM45.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Dan Carpenter [Mon, 6 Sep 2010 12:32:30 +0000 (14:32 +0200)]
Staging: vt6655: fix buffer overflow
"param->u.wpa_associate.wpa_ie_len" comes from the user. We should
check it so that the copy_from_user() doesn't overflow the buffer.
Also further down in the function, we assume that if
"param->u.wpa_associate.wpa_ie_len" is set then "abyWPAIE[0]" is
initialized. To make that work, I changed the test here to say that if
"wpa_ie_len" is set then "wpa_ie" has to be a valid pointer or we return
-EINVAL.
Oddly, we only use the first element of the abyWPAIE[] array. So I
suspect there may be some other issues in this function.
The netfilter hook seems to be misused and may leak skbs in situations
when NF_HOOK returns NF_STOLEN. It may not filter everything as
expected. Also the ethernet bridge tables are not yet capable to
understand batman-adv packet correctly.
It was only added for testing purposes and can be removed again.
Mika Westerberg [Sat, 4 Sep 2010 07:23:23 +0000 (10:23 +0300)]
serial: amba-pl010: fix set_ldisc
Commit d87d9b7d1 ("tty: serial - fix tty referencing in set_ldisc") changed
set_ldisc to take ldisc number as parameter. This patch fixes AMBA PL010 driver
according the new prototype.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi> Cc: Alan Cox <alan@linux.intel.com> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The TIOCGICOUNT device ioctl in both mos7720.c and mos7840.c allows
unprivileged users to read uninitialized stack memory, because the
"reserved" member of the serial_icounter_struct struct declared on the
stack is not altered or zeroed before being copied back to the user.
This patch takes care of it.
Ming Lei [Mon, 6 Sep 2010 15:27:09 +0000 (23:27 +0800)]
USB: otg: twl4030: fix phy initialization(v1)
Commit 461c317705eca5cac09a360f488715927fd0a927(into 2.6.36-v3)
is put forward to power down phy if no usb cable is connected,
but does introduce the two issues below:
1), phy is not into work state if usb cable is connected
with PC during poweron, so musb device mode is not usable
in such case, follows the reasons:
-twl4030_phy_resume is not called, so
regulators are not enabled
i2c access are not enabled
usb mode not configurated
2), The kernel warings[1] of regulators 'unbalanced disables'
is caused if poweron without usb cable connected
with PC or b-device.
This patch fixes the two issues above:
-power down phy only if no usb cable is connected with PC
and b-device
-do phy initialization(via __twl4030_phy_resume) if usb cable
is connected with PC(vbus event) or another b-device(ID event) in
twl4030_usb_probe.
This patch also doesn't put VUSB3V1 LDO into active mode in
twl4030_usb_ldo_init until VBUS/ID change detected, so we can
save more power consumption than before.
This patch is verified OK on Beagle board either connected with
usb cable or not when poweron.
Signed-off-by: Ming Lei <tom.leiming@gmail.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Felipe Balbi <me@felipebalbi.com> Cc: Anand Gadiyar <gadiyar@ti.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb: musb_debugfs: don't use the struct file private_data field with seq_files
seq_files use the private_data field of a file struct for storing a seq_file structure,
data should be stored in seq_file's own private field (e.g. file->private_data->private)
Otherwise seq_release() will free the private data when the file is closed.
Chris Wilson [Mon, 20 Sep 2010 09:31:40 +0000 (10:31 +0100)]
drm/i915: Hold a reference to the object whilst unbinding the eviction list
During heavy aperture thrashing we may be forced to wait upon several active
objects during eviction. The active list may be the last reference to
these objects and so the action of waiting upon one of them may cause
another to be freed (and itself unbound). To prevent the object
disappearing underneath us, we need to acquire and hold a reference
whilst unbinding.
Reported-by: Shawn Starr <shawn.starr@rogers.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18902 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Al Viro [Mon, 20 Sep 2010 14:13:25 +0000 (15:13 +0100)]
frv: double syscall restarts, syscall restart in sigreturn()
We need to make sure that only the first do_signal() to be handled on
the way out syscall will bother with syscall restarts; additionally, the
check on the "signal has user handler" path had been wrong - compare
with restart prevention in sigreturn()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Mon, 20 Sep 2010 14:13:14 +0000 (15:13 +0100)]
frv: avoid infinite loop of SIGSEGV delivery
Use force_sigsegv() rather than force_sig(SIGSEGV, ...) as the former
resets the SEGV handler pointer which will kill the process, rather than
leaving it open to an infinite loop if the SEGV handler itself caused a
SEGV signal.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Mon, 20 Sep 2010 14:13:09 +0000 (15:13 +0100)]
frv: fix address verification holes in setup_frame/setup_rt_frame
a) sa_handler might be maliciously set to point to kernel memory;
blindly dereferencing it in FDPIC case is a Bad Idea(tm).
b) I'm not sure you need that set_fs(USER_DS) there at all, but if you
do, you'd better do it *before* checking the frame you've decided to
use with access_ok(), lest sigaltstack() becomes a convenient
roothole.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 4969c1192d15 ("mm: fix swapin race condition") is now agreed to
be incomplete. There's a race, not very much less likely than the
original race envisaged, in which it is further necessary to check that
the swapcache page's swap has not changed.
Here's the reasoning: cast in terms of reuse_swap_page(), but probably
could be reformulated to rely on try_to_free_swap() instead, or on
swapoff+swapon.
A, faults into do_swap_page(): does page1 = lookup_swap_cache(swap1) and
comes through the lock_page(page1).
B, a racing thread of the same process, faults on the same address: does
page1 = lookup_swap_cache(swap1) and now waits in lock_page(page1), but
for whatever reason is unlucky not to get the lock any time soon.
A carries on through do_swap_page(), a write fault, but cannot reuse the
swap page1 (another reference to swap1). Unlocks the page1 (but B
doesn't get it yet), does COW in do_wp_page(), page2 now in that pte.
C, perhaps the parent of A+B, comes in and write faults the same swap
page1 into its mm, reuse_swap_page() succeeds this time, swap1 is freed.
kswapd comes in after some time (B still unlucky) and swaps out some
pages from A+B and C: it allocates the original swap1 to page2 in A+B,
and some other swap2 to the original page1 now in C. But does not
immediately free page1 (actually it couldn't: B holds a reference),
leaving it in swap cache for now.
B at last gets the lock on page1, hooray! Is PageSwapCache(page1)? Yes.
Is pte_same(*page_table, orig_pte)? Yes, because page2 has now been
given the swap1 which page1 used to have. So B proceeds to insert page1
into A+B's page_table, though its content now belongs to C, quite
different from what A wrote there.
B ought to have checked that page1's swap was still swap1.
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: deal with multiple simultaneously pending signals
alpha: fix a 14 years old bug in sigreturn tracing
alpha: unb0rk sigsuspend() and rt_sigsuspend()
alpha: belated ERESTART_RESTARTBLOCK race fix
alpha: Shift perf event pending work earlier in timer interrupt
alpha: wire up fanotify and prlimit64 syscalls
alpha: kill big kernel lock
alpha: fix build breakage in asm/cacheflush.h
alpha: remove unnecessary cast from void* in assignment.
alpha: Use static const char * const where possible
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
dca: disable dca on IOAT ver.3.0 multiple-IOH platforms
netpoll: Disable IRQ around RCU dereference in netpoll_rx
sctp: Do not reset the packet during sctp_packet_config().
net/llc: storing negative error codes in unsigned short
MAINTAINERS: move atlx discussions to netdev
drivers/net/cxgb3/cxgb3_main.c: prevent reading uninitialized stack memory
drivers/net/eql.c: prevent reading uninitialized stack memory
drivers/net/usb/hso.c: prevent reading uninitialized memory
xfrm: dont assume rcu_read_lock in xfrm_output_one()
r8169: Handle rxfifo errors on 8168 chips
3c59x: Remove atomic context inside vortex_{set|get}_wol
tcp: Prevent overzealous packetization by SWS logic.
net: RPS needs to depend upon USE_GENERIC_SMP_HELPERS
phylib: fix PAL state machine restart on resume
net: use rcu_barrier() in rollback_registered_many
bonding: correctly process non-linear skbs
ipv4: enable getsockopt() for IP_NODEFRAG
ipv4: force_igmp_version ignored when a IGMPv3 query received
ppp: potential NULL dereference in ppp_mp_explode()
net/llc: make opt unsigned in llc_ui_setsockopt()
...
Jan Harkes [Sat, 18 Sep 2010 03:26:01 +0000 (23:26 -0400)]
Coda: mount hangs because of missed REQ_WRITE rename
Coda's REQ_* defines were renamed to avoid clashes with the block layer
(commit 4aeefdc69f7b: "coda: fixup clash with block layer REQ_*
defines").
However one was missed and response messages are no longer matched with
requests and waiting threads are no longer woken up. This patch fixes
this.
Signed-off-by: Jan Harkes <jaharkes@cs.cmu.edu>
[ Also fixed up whitespace while at it -Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sat, 18 Sep 2010 12:42:27 +0000 (08:42 -0400)]
alpha: deal with multiple simultaneously pending signals
Unlike the other targets, alpha sets _one_ sigframe and
buggers off until the next syscall/interrupt, even if
more signals are pending. It leads to quite a few unpleasant
inconsistencies, starting with SIGSEGV potentially arriving
not where it should and including e.g. mess with sigsuspend();
consider two pending signals blocked until sigsuspend()
unblocks them. We pick the first one; then, if we are hit
by interrupt while in the handler, we process the second one
as well. If we are not, and if no syscalls had been made,
we get out of the first handler and leave the second signal
pending; normally sigreturn() would've picked it anyway, but
here it starts with restoring the original mask and voila -
the second signal is blocked again. On everything else we
get both delivered consistently.
It's actually easy to fix; the only thing to watch out for
is prevention of double syscall restart. Fortunately, the
idea I've nicked from arm fix by rmk works just fine...
Testcase demonstrating the behaviour in question; on alpha
we get one or both flags set (usually one), on everything
else both are always set.
#include <signal.h>
#include <stdio.h>
int had1, had2;
void f1(int sig) { had1 = 1; }
void f2(int sig) { had2 = 1; }
main()
{
sigset_t set1, set2;
sigemptyset(&set1);
sigemptyset(&set2);
sigaddset(&set2, 1);
sigaddset(&set2, 2);
signal(1, f1);
signal(2, f2);
sigprocmask(SIG_SETMASK, &set2, NULL);
raise(1);
raise(2);
sigsuspend(&set1);
printf("had1:%d had2:%d\n", had1, had2);
}
Tested-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Matt Turner <mattst88@gmail.com>
Al Viro [Sat, 18 Sep 2010 12:41:16 +0000 (08:41 -0400)]
alpha: fix a 14 years old bug in sigreturn tracing
The way sigreturn() is implemented on alpha breaks PTRACE_SYSCALL,
all way back to 1.3.95 when alpha has grown PTRACE_SYSCALL support.
What happens is direct return to ret_from_syscall, in order to bypass
mangling of a3 (error indicator) and prevent other mutilations of
registers (e.g. by syscall restart). That's fine, but... the entire
TIF_SYSCALL_TRACE codepath is kept separate on alpha and post-syscall
stopping/notifying the tracer is after the syscall. And the normal
path we are forcibly switching to doesn't have it.
So we end up with *one* stop in traced sigreturn() vs. two in other
syscalls. And yes, strace is visibly broken by that; try to strace
the following
#include <signal.h>
#include <stdio.h>
void f(int sig) {}
main()
{
signal(SIGHUP, f);
raise(SIGHUP);
write(1, "eeeek\n", 6);
}
and watch the show. The
close(1) = 405
in the end of strace output is coming from return value of write() (6 ==
__NR_close on alpha) and syscall number of exit_group() (__NR_exit_group ==
405 there).
The fix is fairly simple - the only thing we end up missing is the call
of syscall_trace() and we can tell whether we'd been called from the
SYSCALL_TRACE path by checking ra value. Since we are setting the
switch_stack up (that's what sys_sigreturn() does), we have the right
environment for calling syscall_trace() - just before we call
undo_switch_stack() and return. Since undo_switch_stack() will overwrite
s0 anyway, we can use it to store the result of "has it been called from
SYSCALL_TRACE path?" check. The same thing applies in rt_sigreturn().
Tested-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Matt Turner <mattst88@gmail.com>
Al Viro [Sat, 18 Sep 2010 12:40:07 +0000 (08:40 -0400)]
alpha: unb0rk sigsuspend() and rt_sigsuspend()
Old code used to set regs->r0 and regs->r19 to force the right
return value. Leaving that after switch to ERESTARTNOHAND
was a Bad Idea(tm), since now that screws the restart - if we
hit the case when get_signal_to_deliver() returns 0, we will
step back to syscall insn, with v0 set to EINTR and a3 to 1.
The latter won't matter, since EINTR is 4, aka __NR_write.
results on alpha in immediate message to stdout...
Fix is obvious; moreover, since we don't need regs anymore, we can
switch to normal prototypes for these guys and lose the wrappers.
Even better, rt_sigsuspend() is identical to generic version in
kernel/signal.c now.
Tested-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Matt Turner <mattst88@gmail.com>
Michael Cree [Sun, 19 Sep 2010 06:05:40 +0000 (02:05 -0400)]
alpha: Shift perf event pending work earlier in timer interrupt
Pending work from the performance event subsystem is executed in
the timer interrupt. This patch shifts the call to
perf_event_do_pending() before the call to update_process_times()
as the latter may call back into the perf event subsystem and it
is prudent to have the pending work executed first.
Signed-off-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Matt Turner <mattst88@gmail.com>
All uses of the BKL on alpha are totally bogus, nothing
is really protected by this. Remove the remaining users
so we don't have to mark alpha as 'depends on BKL'.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: linux-alpha@vger.kernel.org Signed-off-by: Matt Turner <mattst88@gmail.com>
Alpha SMP flush_icache_user_range() is implemented as an inline
function inside include/asm/cacheflush.h. It dereferences @current
but doesn't include linux/sched.h and thus causes build failure if
linux/sched.h wasn't included previously. Fix it by including the
needed header file explicitly.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Matt Turner <mattst88@gmail.com>
Chris Wilson [Tue, 20 Jul 2010 22:44:45 +0000 (15:44 -0700)]
drm/i915: use GMBUS to manage i2c links
Use the GMBUS interface rather than direct bit banging to grab the EDID
over DDC (and for other forms of auxiliary communication with external
display controllers). The hope is that this method will be much faster
and more reliable than bit banging for fetching EDIDs from buggy monitors
or through switches, though we still preserve the bit banging as a
fallback in case GMBUS fails.
Based on an original patch by Jesse Barnes.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
dca: disable dca on IOAT ver.3.0 multiple-IOH platforms
Direct Cache Access is not supported on IOAT ver.3.0 multiple-IOH platforms.
This patch blocks registering of dca providers when multiple IOH detected with IOAT ver.3.0.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log